ROYCE 639 40 CANALI AM/SSB

SPECIFICATIONS ALIGNMENT INSTRUCTIONS

GENERAL 1. RECEIVER
1. Semiconductors : 22 Transistors, 2 FET, 10 IC's, 54 Diodes and 3 LED
2. Frequency Range : 26.965MHZ — 27.405MHZ 1)
Set the Mode Switch to AM, Volume Control at maximum, Squelch at minimum, Clarifier in
3. Modes of Operation : AM, Lower Sideband and Upper Sideband the center and the CB-PA Switch to CB.
4. Controls : Volume Control with power on-off switch 2) Set the SSG on Channel 19 and Channel Selector of the unit on Channel 19.
> Variable Squelch Control Then, connect the Power Supply and 8 ohms Dummy Load to the transceiver unit.
Mike Gain Control. 3) Feed the signal from the SSG and set the audio output for a peak reading by adjusting T-1, T-2,
RF Gain Control. T-3, and T-4.
: SWR/CAL Control. In this case be sure that antenna input should be less than 1nV at the AF standard output power.
: Mode Selector Switches Also, make sure that the audio on the oscilloscope is a sine wave.
: Clarifier Control 4) Set the antenna input at 1uV so that the antenna power may be more than 0.5. Watt at the
: Channel Selector Switch maximum volume of all channels.
Noise Blanker/ANL Switch. 5) Set the antenna input at 1,000uV so that the output power should be more than 3.0 watts at
Meter Select Switch. the maximum volume.
: CH-9 Priority Switch 6) Set the antenna input to 50,000uV and the low frequency output to 0.5 watt by volume con-
: Bright/Dim Switch trol. Then, decrease the antenna input until the low frequency output stays 10 dB lower. Be
: CB-PA Switch sure that the antenna input then should be less than 5yV.
5. Connectors and Jacks : Microphone Connector 7) Set the antenna input to 100uV and the meter indication to 9 by VR-2.
: Coaxial type Antenna Connector 8) Set the volume control and squelch control at maximum, and set the tight squelch by VR3 so
: Public Address Speaker Jack that the output from speaker is heard when the antenna input is increased upto 1,000uV.
External Speaker Jack 9) Set the antenna input to 0.7V and be sure that the low frequency output should be over 10 dB
: DC Power Jack more when the modulation of the SSG is tumed off at the normal output.
Speaker : 3-1/2 inches, 8 ohms 10) Set the Mode Switch to USB, Volume Control at maximum, Squelch at minimum and Clarifier
Microphone Dynamic Microphone (500 Ohms) in the center. Tune off the modulation of the SSG and remove the frequency by 1 KHz.
Power Supply 13.8VDC 11) Make sure that the maximum sensitivity should be less than 1pV.
CANO
Dimensions > 8° (W) x 1-1/8” (H) x 7-5/16”(D) Make sure of AGC like with AM.
10. Weight : 4LBS 07 02S 13) Set the antenna input to 0.2uV and keep the AF output to be over 10 dB lower when the
RECEIVER antenna input is turned off at the normal output.
SensitivityatS/N 10dB : AM..... 0.5uV SSB... <..0.2uV . TRANSMITTER
Selectivity > AM..... 5KHZ SSB..... 2.2KHZ
AGC Figure of Range : 80dB 1) Connection of test equipment.
Squelch Range ; > 0.5uV — 1000uV * Power supply at 13.8 VDC.
Audio Output Power : 3 Watts * Connect a Power meter, oscilloscope frequency counter, spectrum analyzer and P-P RF volt
Distortion at input 100uV : 6% meter to the RF output connector.
Audio Frequency Response : 300 — 2200HZ * Connect an AF oscillator and AF volt meter to the microphone connector.
Supurious Response More than 45dB supurious signal is required to produce the 2) Power adjustment.
same amount of audio output as the desired receive signal. * Set the mode switch to AM.
. IF Frequency : 9.785MHZ * Adjust T-5, 8, 9, L-12, and L-3 for the maximum point.
Po
SCNOAPWN>
com. Current Drain no audio : 500mA * Adjust L-4 for 3.6W output.
SSB TRANSMITTER * Adjust L-2 to increase 2nd harmonic.
1. RF Output Power 12 Watts PEP
3) Frequency-Make sure every channel stays within +800Hz.
2. Carrier Suppression : More than 40dB
4) Modulation Limiter Adjustment.
* Putin 1KHz and 20mV signal from AF oscillator and adjust VR7 for 90% modulation
3. Unwanted Sideband Suppression :; More than 50dB
4. Harmonic Suppression More than 60dB
5) Modulation capability.
5. Current Drain * Put in 1kHz signal by AF oscillator and get 90% modulation for the minus side. The plus side
: 850mA
should be over 80%.
AM TRANSMITTER 6) SSB.
1. RF Output Power : 4 Watts * Set the mode switch to USB.
2. Modulation Capability : More than 80% * Put in two-tone signal of 1KHz and 1.6KHz by two AF oscillators.
3. Harmonic Suppression : More than 60d8 7) ALC alignment.
4. Current Drain 1800mA * Adjust the two-tone signal of AF oscillator for 3 WW RF power output.
* Adjust VR-11 for 11 W PEP RF power output when the two-tone signal isincreased by 20 dB.
8) Carrier suppression.
* Cut off the two-tone signal and make sure the output level of the carrier is below —40 dB.
* Set the mode switch to LSB and do the same.
ROYCE 639
Q6 Q7
250456 2SC456

CI4A, 145 ,146, 1467,150,153 157,158

Cue 0”
C149 164220

+
13.6V
 (Jue
—yh—

te’
ec rf
ie
——

3 8 | oo
A {| zaw
q54
ieee
COMPRESSOR

oven? | eoereeee
© 13.8V DC
||
l
{
l

Bieceet
are

Lg
J
}
,
|
I
MOD.

DET.
OET.

jSS8

Q18
BALANCED

QtS |

AMC
SSB

SS
Icé6
1C4
0S

> >
L_. re ox
| | 2|
s FI a I celle ie |
g) 1 |3 ee
fis See a
oS)
«
| | fs ! ne bt dla
f) ig | ! a
Q5

g rok | ! | Fite |
te)
C2,3_

~
Ro 0

|
Te | t ;
|
|
|

|
|
|
oo eae ‘ l l 4
sls Po ow g)38 | | ! ja ne
| ze 6! CO a OoBe | | | en |
lel fetid
| |
f
| £2 |
eo | ir] | | |
a
SCHEMA A BLOCCHI

a ‘7
|

a ae eT yen
a|

een J
Sa}
--©ig9f
a

Ww
fey
u |

|
|
I
: Q
x | 3! precslssiseedess J ' Oo .| |
Si| 1| ||
|
5
WwW
| lg g |
°
9.78MHz

re |
: |RB <| Z
Z
be || |
| 7 ig f | 1 |
: ! 3
O
:
'
Si,
a Se ee
ol
ti4
|
a
|
! | | 3 5
ig | « |
|
3 |
3
a
!| 4| |
tl
ue
rd fe | \«
ua
es | o> acece 4
|
| | | |
see + seen | 1 |
by 1
Fr) J Is”
i a
qi ee ean
| « | |
Q3

35 ae
[
ote S | |
i ae ; 8 ; |
i
a
a.
a
ta a 4aa a
te |7
cr te
mee
“
ryeoe
|
FE
a
Lig [ett oo
BLANKER
NOISE

= | |
Tae: aL. ae
|
1c}

z | |
w w
x
Ee
)
: l| o a
= i (asa A va 3 | |2] | 3
Sok rz | =) 5)
X
| |
| oe |
Ae deb
|ee
JCapa
ae
ee
to
See
i
: ie la fe Oe 28 :
|
| !
on
L_| $
a
ne

NY,
ad
a evi eee
. | |
r | 34 | |
a
ce
alla
Raae
|us)
 =oO r.o)
AST Aa /

2SA 67

2SA 67 ”
co
29 2oS
OO | m
2 oOo; e Oo]
We ee
© | ~~ } ——{ N
0 | é -
é é
fo] ‘a eo Nw
2 OQ}; ar = —
ie
N
ee
-
N a B x<
aes os
fee) s
~ eats -= — -_
re) «6 + ~ e =>
a aeMe a be | Maan ge asia
sor : ° °
~ olin ak
foe} oe) C4
es Bs e
~ e s
o;es .
N —)
a ~
=
Sioloao x
S2;e7rs
xl ke oO
fee a ~ olo
Pee aria
Ve (V
om

& pi oO
i olo
os ~ Rae Bra
”
QUELCH

QUELCH
O SQUELCH
O SQUELCH
CARTA DELLE TENSIONI

H8D1210

[e|sla |3/8/2/8/3/3/3/a[ala[=/s|sisisis
[elsls o2)3/5/8/2/3/3/3)8[3[s[ale/2/2/3
[els|s <|3/8/8/8/3/3/3[3[s[afa/sizfsis\
[s/s/s! e/s/8/als/slalal=/3/3/ais/sis/s\
[els[s °/3/3/3/8/8[3/3/3/2/3[s[aiaisia\
[s/s/s eiINNals/s[a[e[als/a[aiaisis/a
eee BBBRSA
EBB REEIN
ENN
[8 [2/8 [8N[22 INNA
Pe AAAAAAAAN
[EDSTE
— PINAAAAAAAAANEAAN
E872: EIWAAAANAAAAAANEAAN