Technical Data Sheet
Approved 33222;33223 1,2 33222 epoxy ^(ValidationDate) 1
Marathon 1000 GF
Product description
This is a two component polyamine cured epoxy coating. It is a high build, solvent free, glass flake reinforced
product. It has very good impact and abrasion resistance. Suitable for environments with very high corrosivity,
such as areas in the splash or tidal zone. Can be used as primer, mid coat, finish coat or as single coat system in
atmospheric and immersed environments. Suitable for properly prepared carbon steel substrates.
Typical use
Protective:
Suitable for structural steel and piping to be exposed to corrosive environments up to very high and immersed.
Recommended for offshore environments, refineries, power plants, bridges, buildings, mining equipment and
general structural steel. Specially suited in areas where high mechanical strength is required, such as splash or
tidal zones.
Can be used as a non-slip deck system in combination with appropriate Anti-Skid aggregate and finish coat.
Compatible with cathodic protection systems.
Other
Approvals and certificates
Pre-qualified in accordance with NORSOK M-501 in selected systems
Additional certificates and approvals may be available on request.
Colours
selected range of colours
Product data
Property Test/Standard Description
Solids by volume ISO 3233 98 ± 2 %
Flash point ISO 3679 Method 1 100 °C
Density calculated 1.4 kg/l
Region Regulation Test Standard VOC Value
US CARB(SCM)2020 / SCAQMD rule 1113 Calculated 47 g/l
Hong Kong Air Pollution Control (VOC) Regulation Calculated 47 g/l
EU European Paint Directive 2004/42/CE Calculated 47 g/l
EU IED Industrial Emission Directive 2010/75/EU Calculated 47 g/l
Korea Korea Clean Air Conservation Act KS M ISO 11890-1 67 g/l
China GB 30981-2020 Limit of harmful GB/T 34682-2017 8.3 18 g/l
substances of industrial protective coatings
Date of issue: 28 February 2025 Page: 1/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Marathon 1000 GF
The provided data is typical for factory produced products, subject to slight variation depending on colour.
Film thickness per coat
Typical recommended specification range
Dry film thickness 500 - 1000 μm
Wet film thickness 510 - 1020 μm
Theoretical spreading rate 2 - 1 m²/l
When used on horizontal areas as part of a deck coating system the maximum DFT is 2000 μm.
Surface preparation
Surface preparation summary table
Surface preparation
Substrate Minimum Recommended
Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1)
Shop primed steel Clean, dry and undamaged approved Sweep blasted or alternatively blasted
shop primer to Sa 2 (ISO 8501-1) of at least 70 %
of the surface.
Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating coating
Application
Application methods
The product can be applied by
Spray: Use airless spray, or two component heated airless spray equipment.
Brush: Recommended for stripe coating and small areas. Care must be taken to achieve the
specified dry film thickness.
Date of issue: 28 February 2025 Page: 2/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Marathon 1000 GF
Product mixing ratio (by volume)
Marathon 1000 GF Comp A 3 part(s)
Marathon 1000 GF Comp B 1 part(s)
Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17
Thinning max.: 5 %
Thinning is not normally required. Consult the local representative for advice during application in extreme
conditions. Do not thin more than allowed by local environmental legislation.
Note: Korean VOC regulation "Korea Clean Air Conservation Act" and its corresponding thinning limit will prevail
over recommended thinning volumes.
Guiding data for airless spray
Nozzle tip (inch/1000): 21-31
Pressure at nozzle (minimum): 210 bar/3000 psi
Heavy duty nozzles to be used.
Pump capacity: 2.2 l/min - 4.8 l/min
Drying and Curing time
Substrate temperature 5 °C 10 °C 15 °C 23 °C 40 °C
Surface (touch) dry 21 h 14 h 10 h 7 h 3 h
Walk-on-dry 32 h 19 h 16 h 9 h 4 h
Dry to over coat, minimum 32 h 19 h 16 h 9 h 4 h
Dried/cured for immersion 14 d 10 d 10 d 7 d 3 d
Dried/cured for service 14 d 10 d 10 d 7 d 3 d
For maximum overcoating intervals, refer to the Application Guide (AG) for this product.
Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.
Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.
Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.
Dry to over coat, minimum: The recommended shortest time before the next coat can be applied.
Dried/cured for immersion: Minimum time before the coating can be permanently immersed in sea water.
Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.
Date of issue: 28 February 2025 Page: 3/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Marathon 1000 GF
Induction time and Pot life
Paint temperature 23 °C
Pot life 45 min
Reduced at higher temperatures, and with increased mixing volumes.
Heat resistance
Temperature
Continuous Peak
Dry, atmospheric 120 °C -
Immersed, sea water 50 °C 60 °C
Peak temperature duration max. 1 hour.
The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.
Note that the coating will be resistant to various immersion temperatures depending on the specific chemical
and whether immersion is constant or intermittent. Heat resistance is influenced by the total coating system. If
used as part of a system, ensure all coatings in the system have similar heat resistance.
Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.
Previous coat: epoxy, zinc rich epoxy, inorganic zinc silicate
Subsequent coat: polyurethane, polysiloxane, epoxy, vinyl epoxy
Packaging (typical)
Volume Size of containers
(litres) (litres)
Marathon 1000 GF Comp A 13.5 20
Marathon 1000 GF Comp B 4.5 5
The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.
Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool,
well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed.
Handle with care.
Date of issue: 28 February 2025 Page: 4/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Marathon 1000 GF
Shelf life at 23 °C
Marathon 1000 GF Comp A 12 month(s)
Marathon 1000 GF Comp B 12 month(s)
In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.
Environmental Documentation
This product can contribute to Green Building Standard credits. Please refer to Jotun.com for more information
or contact your local Jotun representative.
Environmental Product Declaration (EPD) is available at www.epd-norge.no
Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.
Health and safety
Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.
Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products and epoxy based products used as a finish coat may chalk when exposed to
sunlight and weathering.
Colour and gloss retention on topcoats/finish coats may vary depending on type of colour, exposure
environment such as temperature, UV intensity etc., application quality and generic type of paint. Contact your
local Jotun office for further information.
Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.
Date of issue: 28 February 2025 Page: 5/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
