LCD-X1 manual panel use instructions-2022 latest version

一、 Appearance size and material

Product shell is ABS, liquid crystal transparent window is imported high
hardness acrylic, hardness value is equivalent to tempered glass.

Look-up view Top view

Side view, the conversion ring 22.2, 25.4, 28.6mm is optional

二、 Operating voltage and wiring mode

1. Operating voltage: DC24V, 36V, 48V, 52V, 60V (instrument selection and
setting), and other voltages can be customized.

2、mode of connection:
1
Note: the leads of some products use waterproof connector,
and the user cannot see the lead color in the harness.

3. function declaration:
1. Display function
Speed display, power driving gear display, power quantity indication, fault prompt, total
mileage, single mileage, headlight display, single driving time display
2. Control and setting functions
Power switch control, headlight switch control, 6 Km/h point movement control, wheel
Diameter setting, maximum speed setting, idle automatic hibernation time setting, backlight
brightness setting, voltage level setting, etc
3. Communication protocol: UART
All contents of the display screen (full display in boot 1S)

Display content introduction

3.1 Headlights, USB charging prompt, brake status prompt,

3.2 Battery display BATTERY (BMS support)

3.3 Multi-function display area

2
 Total mileage ODO, single mileage TRIP, digital voltage Pow, single ride time Time, metric
mileage Km, British system mileage Mile;

3.4 Power-assist gear

Range 0-9 can display, 6km boost and cruise control display;

3.5 Speed display area

Maximum speed MAX, average speed AVG
Unit of MPH, KM / H
The instrument calculates the true speed based on the wheel diameter and the signal data

3.6 Vehicle status, and the significance of the fault code

Significance of the vehicle status code:
Status State meaning remarks
code
(decimal
system)
0 whack
1 continue to have
2 stop a vehicle by applying the brake
3 Power sensor failure (ride sign) This is not
going to happen
4 6KM / H Cruise
5 Real-time cruise
6 Battery under pressure
7 Motor failure
8 Turn the fault
9 Controller fault
10 Communication reception failure
11 Communication send fault
12 A BMS communication failure
13 Headlight fault

3.7. Settings
P01: backlight brightness, 1 the darkest, 3 the brightest;
P02: Mileage unit, 0: KM; 1: MILE;
P03: Voltage level: 24V, 36V, 48V, default 36V;
P04: Sleep time: 0, no sleep; other numbers are sleep time, range: 1-60; per unit
minute;
P05: Power gear: 0,3 gear mode: 1,2V, 2 gear, 3V, 3,4V;
1,5 mode: 1,2V, 2,2.5V, 3,3V,4 gear, 3.5V, 5 gear, 4V;
P06: Wheel diameter: unit, inch; precision: 0.1;
P07: Number of speed measuring magnetic steel: range: 1-100;

3
 P08: Speed limit: range 0-100 km/h, 100 indicates no speed limit,
1. Non-communication state (instrument control): turn off PWM
output when the speed is greater than the speed set; when the
speed is less than the set speed, automatically open PWM output
and the driving speed is ± 1 km/h; (for power speed limit only, no
speed limit not)
2. Communication status (Controller Control): Drive speed is
maintained at the set point,
Error: ± 1 km/h; (transfer speed limit)
Note: The value here is based on km. When the unit setting is converted
from km to mile, the speed value of the display interface will be
automatically converted to the correct mile value, but the speed limit value
data set at this menu under the mile interface is not converted, which is
inconsistent with the actual displayed mile speed limit value;
P09: zero start, non-zero start setting, 0: zero start; 1: Non-zero start;
P10: Drive mode setting 0: Power drive (how much power output by power
gear, the switch is invalid).
1: Electric drive (the power gear is invalid by the
knob drive).
2: Both power drive and electric drive coexist
(electric drive zero start state).
P11: Power assist sensitivity setting range: 1-24;
P12: Power to start the strength setting range: 0-5;
P13: power magnetic steel disk type set 5,8,12 grain magnetic steel three types
P14: The controller flow limit value sets the default 12A range: 1-20A
P15: The function has not been yet opened
P16: ODO zero clearance setting long press the key for 5 seconds ODO zero
clearance
P17:0: Non-enable cruise, 1: enable cruise; automatic cruise is optional (valid for
Protocol 2 only)
P18: Display speed ratio adjustment range: 50%~150%,
P19:0 gear enabling level, 0: including 0 gear, 1: excluding 0 gear
P20:0:2 Agreement 1:5S Agreement 2: standby 3: standby

4.Button Introductions

4.1 During riding, need change PAS/Speed grades, shortly press

4.2 During riding, need change data in Multi-function Area, shortly press ;

4
Long press , could switch status between MODE and ON/OFF;
Long press as a compound button, is mainly used for parameter setting, which could reduce
misoperation due to complicated operation.
(No compound button with short-time press, because it’s difficult to operate.)

4.3 Specific operation explanations

4.3.1 Change PAS grade
Suppose it’s PAS mode now,

shortly press , PAS grade +1

shortly press , PAS grade -1

4.3.2 Shift the speed display

Long press + , to shift the way of speed display

4.3.3 ON/OFF 6KM/H cruising, ON/OFF Headlight, Reset ODO

When e-bike stops, long press to enter 6KM/H cruising mode. Stop
pressing to exit the cruise mode;

Long press to turn ON/OFF Headlight;

At P16, long press for 5s to reset ODO.

4.3.4 ON/OFF the screen

Long press to turn ON/OFF the screen.

4.3.5 Change data in multi-function Area

Shortly press to change data.

4.3.5 Parameters setting

Long press + to start setting parameters, such as wheel

size(inch), background luminance… (Refer to P01-P20)

On the setting interface, shortly press , or to plus/minus

value. Parameters would be shining after modifying, choose the ones you prefer,
5
 a. Long press to save the value, the shining would stop.

b. Shortly press to shift to the next parameter, and to save current values
at the same time.

c. Press + to exit setting parameters and to save values. If

not press these buttons, it would exit and save parameters modified automatically 10s
later.
Note: Due to the upgrade of the company's product, the display content of the
product part you get will be different from the instructions, but it will not
affect your normal use.