++ port security ++
in switch
interface fastethernet 0/4
switchport mode access
switchport port - security
go to your connected 0/4 pc and copy mac address
switchport port-security maximum 1
switchport port - security mac-address ...... paste mac address where (....)
switchport port - security violation shutdown
switchport port mac-address sticky
switchport port mac-address sticky ..... paste mac address where (....)
sh spanning-tree interface fastethetrnet 0/4 to show
fir sh spanning-tree wala command aur iska proof ka ss dedena
C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(25r)FX, RELEASE SOFTWARE (fc4)
Cisco WS-C2960-24TT (RC32300) processor (revision C0) with 21039K bytes of memory.
2960-24TT starting...
Base ethernet MAC Address: 0060.5C36.DBD0
Xmodem file system is available.
Initializing Flash...
flashfs[0]: 1 files, 0 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 64016384
flashfs[0]: Bytes used: 4670455
flashfs[0]: Bytes available: 59345929
flashfs[0]: flashfs fsck took 1 seconds.
...done Initializing Flash.
Boot Sector Filesystem (bs:) installed, fsid: 3
Parameter Block Filesystem (pb:) installed, fsid: 4
Loading "flash:/2960-lanbasek9-mz.150-2.SE4.bin"...
########################################################################## [OK]
Smart Init is enabled
smart init is sizing iomem
TYPE MEMORY_REQ
TOTAL: 0x00000000
Rounded IOMEM up to: 0Mb.
Using 6 percent iomem. [0Mb/512Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 15.0(2)SE4, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 26-Jun-13 02:49 by mnguyen
Initializing flashfs...
fsck: Disable shadow buffering due to heap fragmentation.
flashfs[2]: 2 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 32514048
flashfs[2]: Bytes used: 11952128
flashfs[2]: Bytes available: 20561920
flashfs[2]: flashfs fsck took 2 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.
Checking for Bootloader upgrade..
Boot Loader upgrade not required (Stage 2)
POST: CPU MIC register Tests : Begin
POST: CPU MIC register Tests : End, Status Passed
POST: PortASIC Memory Tests : Begin
POST: PortASIC Memory Tests : End, Status Passed
POST: CPU MIC interface Loopback Tests : Begin
POST: CPU MIC interface Loopback Tests : End, Status Passed
POST: PortASIC RingLoopback Tests : Begin
POST: PortASIC RingLoopback Tests : End, Status Passed
POST: PortASIC CAM Subsystem Tests : Begin
POST: PortASIC CAM Subsystem Tests : End, Status Passed
POST: PortASIC Port Loopback Tests : Begin
POST: PortASIC Port Loopback Tests : End, Status Passed
Waiting for Port download...Complete
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco WS-C2960-24TT-L (PowerPC405) processor (revision B0) with 65536K bytes of
memory.
Processor board ID FOC1010X104
Last reset from power-on
1 Virtual Ethernet interface
24 FastEthernet interfaces
2 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
64K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 00:60:5C:36:DB:D0
Motherboard assembly number : 73-10390-03
Power supply part number : 341-0097-02
Motherboard serial number : FOC10093R12
Power supply serial number : AZS1007032H
Model revision number : B0
Motherboard revision number : B0
Model number : WS-C2960-24TT-L
System serial number : FOC1010X104
Top Assembly Part Number : 800-27221-02
Top Assembly Revision Number : A0
Version ID : V02
CLEI Code Number : COM3L00BRA
Hardware Board Revision Number : 0x01
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 26 WS-C2960-24TT-L 15.0(2)SE4 C2960-LANBASEK9-M
Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 15.0(2)SE4, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 26-Jun-13 02:49 by mnguyen
Press RETURN to get started!
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to
up
%LINK-5-CHANGED: Interface FastEthernet0/2, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to
up
%LINK-5-CHANGED: Interface FastEthernet0/3, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to
up
Switch>enable
Switch#
Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface FastEthernet0/1
Switch(config-if)#swi
Switch(config-if)#switchport mod
Switch(config-if)#switchport mode acc
Switch(config-if)#switchport mode access
Switch(config-if)#swi
Switch(config-if)#switchport por
Switch(config-if)#switchport port-security max
Switch(config-if)#switchport port-security maximum 1
Switch(config-if)#sw
Switch(config-if)#switchport por
Switch(config-if)#switchport port-security mac
Switch(config-if)#switchport port-security mac-address 000C.858A.9783
Switch(config-if)#swi
Switch(config-if)#switchport po
Switch(config-if)#switchport port-security v
Switch(config-if)#switchport port-security violation s
Switch(config-if)#switchport port-security violation shutdown
Switch(config-if)#switchport port-security mac-address 000C.858A.9783
Found duplicate mac-address 000c.858a.9783.
Switch(config-if)#sw
Switch(config-if)#switchport po
Switch(config-if)#switchport port-security ma
Switch(config-if)#switchport port-security mac
Switch(config-if)#switchport port-security mac-address st
Switch(config-if)#switchport port-security mac-address sticky 000C.858A.9783
Sticky mac is not enabled.
Switch(config-if)#sh spa
Switch(config-if)#sh spann
Switch(config-if)#exit
Switch(config)#sh s
Switch(config)#sh spa
Switch(config)#sh spann
Switch(config)#ecit
^
% Invalid input detected at '^' marker.
Switch(config)#exit
Switch#
%SYS-5-CONFIG_I: Configured from console by console
s
% Ambiguous command: "s"
Switch#sh sp
Switch#sh spanning-tree inter
Switch#sh spanning-tree interface fas
Switch#sh spanning-tree interface fastEthernet 0/1
Vlan Role Sts Cost Prio.Nbr Type
---------------- ---- --- --------- -------- --------------------------------
VLAN0001 Desg FWD 19 128.1 P2p
Switch#
Switch#
Switch#
Switch#
