Processing Data Sheet Ultramid ®
B3GM35 bk 30564
11/2018 PA6-(GF15+M25)
Product description
A glass-fibre and mineral reinforced injection moulding grade for industrial articles having medium rigidity and high
dimensional stability, used e.g. for engine covers, handles, mountings, etc.
Physical form and storage
The product is supplied dry and ready to use in moisture-proof packaging. The material is in the form of cylindrical or flat
pellets. Its bulk density is about 0,7 g/cm³. Standard packs are the special 25 kg bag and the 1000 kg bulk container
(octagonal IBC=intermediate bulk container made from corrugated board with a liner bag). Subject to agreement other
forms of packaging and shipment in tankers by road or rail are also possible. All containers are tightly sealed and should
be opened only immediately prior to processing. To ensure that the perfectly dry material delivered cannot absorb moisture
from the air the containers must be stored in dry rooms and always carefully sealed again after some of the material has
been withdrawn. Ultramid® can be stored for a longer period of time in dry, well vented rooms without any change to
properties. After longer storage times (> 3 months for IBC or > 2 years for bags) or if material from previously opened
containers is used, drying is recommended to remove absorbed moisture. Containers stored in cold rooms should be
allowed to equalise to normal temperature so that no condensation forms on the pellets.
Product safety
In case processing is done under conditions as recommended (cf. processing data sheet) melts are thermally stable and
do not generate hazards by molecular degradation or the evolution of gases and vapors. Like all thermoplastic polymers
the product decomposes on exposure to excessive thermal load, e.g. when it is overheated or as a result of cleaning by
burning off. Further information is available from the safety data sheet.
Note
The data contained in this publication are based on our current knowledge and experience. In view of the many factors
that may affect processing and application of our product, these data do not relieve processors from carrying out their own
investigations and tests; neither do these data imply any guarantee of certain properties, nor the suitability of the product
for a specific purpose. Any descriptions, drawings, photographs, data, proportions, weights etc. given herein may change
without prior information and do not constitute the agreed contractual quality of the product. It is the responsibility of the
recipient of our products to ensure that any proprietary rights and existing laws and legislation are observed.
In order to check the availability of products please contact us or our sales agency.
BASF SE
67056 Ludwigshafen, Germany
Ultramid ® B3GM35 bk 30564
Processing Data Sheet
Test method Unit Values
Properties
Polymer abbreviation - - PA6-(GF15+M25)
Density ISO 1183 kg/m³ 1480
Melt volume rate MVR 275 °C/5 kg ISO 1133 cm³/10min 40
Drying
Moisture, max. - % 0.15
Moisture, optimal 1) - % 0.03 - 0.06
Dryer temperature 2) - °C 80
Drying time 3) - h 4
Injection molding
Melt temperature range - °C 270 - 290
Melt temperature, optimal - °C 280
Mold temperature range - °C 80 - 90
Mold temperature, optimal - °C 80
Residence time, max. - min 10
Machine Settings
Temperature hopper throat - °C 80
Cylinder temperature 1 (feed zone) - °C 260
Cylinder temperature 2 (compression) - °C 270
Cylinder temperature 3 (metering-zone, in front of the screw) - °C 280
Cylinder temperature 4 (nozzle) - °C 280
Peripheral screw speed - m/s ≤ 0.3
Shrinkage
Processing shrinkage, constrained, longitudinal (TM = 280 °C, TW = 80 °C) 4) - % 0.4
Footnotes
1) Excessive drying of the granules may lead to an increase of melt viscosity during processing.
2) Dry air dryer; drying time is dependent on the inital moisture content of the granules, drying temperature and the dew point of the dried air.
3) In case of improper storage (e.g. open packages) drying time may have to be extended.
4) Model housing with central sprue, measures of the base: 107 x 47 x 1.5 mm.
BASF SE
67056 Ludwigshafen, Germany
