Total Losses in Power Distribution and

Transmission Lines (1)

Total Losses in Power Distribution and Transmission Lines (on photo: Power sunset over
Kampala City, Uganda)

Introduction
Power generated in power stations pass through large and complex networks like transformers,
overhead lines, cables and other equipment and reaches at the end users. It is fact that the unit of
electric energy generated by Power Station does not match with the units distributed to the
consumers. Some percentage of the units is lost in the distribution network.

This difference in the generated and distributed units is known as Transmission and
Distribution loss. Transmission and Distribution loss are the amounts that are not paid for by
users.
T&D Losses = (Energy Input to feeder(Kwh) – Billed Energy to Consumer(Kwh)) / Energy
Input kwh x 100

Distribution Sector considered as the weakest link in the entire power sector. Transmission
Losses is approximate 17% while Distribution Losses is approximate 50%.

There are two types of Transmission and Distribution Losses:

1. Technical Losses
2. Non Technical Losses (Commercial Losses)

1. Technical Losses

The technical losses are due to energy dissipated in the conductors, equipment used for
transmission line, transformer, subtransmission line and distribution line and magnetic losses in
transformers.

Technical losses are normally 22.5%, and directly depend on the network characteristics and the
mode of operation.

The major amount of losses in a power system is in primary and secondary distribution lines.
While transmission and sub-transmission lines account for only about 30% of the total losses.
Therefore the primary and secondary distribution systems must be properly planned to ensure
within limits.

 The unexpected load increase was reflected in the increase of technical losses above the
normal level
 Losses are inherent to the distribution of electricity and cannot be eliminated.

There are two Type of Technical Losses.

1. Permanent / Fixed Technical losses

 Fixed losses do not vary according to current. These losses take the form of heat and
noise and occur as long as a transformer is energized
 Between 1/4 and 1/3 of technical losses on distribution networks are fixed losses. Fixed
losses on a network can be influenced in the ways set out below
 Corona Losses
 Leakage Current Losses
 Dielectric Losses
 Open-circuit Losses
 Losses caused by continuous load of measuring elements
  Losses caused by continuous load of control elements

2. Variable Technical losses

Variable losses vary with the amount of electricity distributed and are, more precisely,
proportional to the square of the current. Consequently, a 1% increase in current leads to an
increase in losses of more than 1%.

 Between 2/3 and 3/4 of technical (or physical) losses on distribution networks are
variable Losses.
 By increasing the cross sectional area of lines and cables for a given load, losses will fall.
This leads to a direct trade-off between cost of losses and cost of capital expenditure. It
has been suggested that optimal average utilization rate on a distribution network that
considers the cost of losses in its design could be as low as 30 per cent.
 Joule losses in lines in each voltage level
 Impedance losses
 Losses caused by contact resistance.

Main Reasons for Technical Losses

1. Lengthy Distribution lines

In practically 11 KV and 415 volts lines, in rural areas are extended over long distances to feed
loads scattered over large areas. Thus the primary and secondary distributions lines in rural areas
are largely radial laid usually extend over long distances.

This results in high line resistance and therefore high I2R losses in the line.

 Haphazard growths of sub-transmission and distribution system in to new areas.

2. Inadequate Size of Conductors of Distribution lines

The size of the conductors should be selected on the basis of KVA x KM capacity of standard
conductor for a required voltage regulation, but rural loads are usually scattered and generally
fed by radial feeders. The conductor size of these feeders should be adequate.

3. Installation of Distribution transformers away from load centers

Distribution Transformers are not located at Load center on the Secondary Distribution System.

In most of case Distribution Transformers are not located centrally with respect to consumers.
Consequently, the farthest consumers obtain an extremity low voltage even though a good
voltage levels maintained at the transformers secondary.
This again leads to higher line losses. (The reason for the line losses increasing as a result of
decreased voltage at the consumers end therefore in order to reduce the voltage drop in the line
to the farthest consumers, the distribution transformer should be located at the load center to
keep voltage drop within permissible limits.)

4. Low Power Factor of Primary and secondary distribution system

In most LT distribution circuits normally the Power Factor ranges from 0.65 to 0.75. A low
Power Factor contributes towards high distribution losses.

For a given load, if the Power Factor is low, the current drawn in high And the losses
proportional to square of the current will be more. Thus, line losses owing to the poor PF can be
reduced by improving the Power Factor.

This can be done by application of shunt capacitors.

 Shunt capacitors can be connected either in secondary side (11 KV side) of the 33/11 KV
power transformers or at various point of Distribution Line.
 The optimum rating of capacitor banks for a distribution system is 2/3rd of the average
KVAR requirement of that distribution system.
 The vantage point is at 2/3rd the length of the main distributor from the transformer.
 A more appropriate manner of improving this PF of the distribution system and thereby
reduce the line losses is to connect capacitors across the terminals of the consumers
having inductive loads.
 By connecting the capacitors across individual loads, the line loss is reduced from 4 to
9% depending upon the extent of PF improvement.

5. Bad Workmanship

Bad Workmanship contributes significantly role towards increasing distribution losses.

Joints are a source of power loss. Therefore the number of joints should be kept to a minimum.
Proper jointing techniques should be used to ensure firm connections.

Connections to the transformer bushing-stem, drop out fuse, isolator, and LT switch etc. should
be periodically inspected and proper pressure maintained to avoid sparking and heating of
contacts.

Replacement of deteriorated wires and services should also be made timely to avoid any cause of
leaking and loss of power.

6. Feeder Phase Current and Load Balancing>

One of the easiest loss savings of the distribution system is balancing current along three-
phase circuits.
Feeder phase balancing also tends to balance voltage drop among phases giving three-phase
customers less voltage unbalance. Amperage magnitude at the substation doesn’t guarantee load
is balanced throughout the feeder length.

Feeder phase unbalance may vary during the day and with different seasons. Feeders are
usually considered “balanced” when phase current magnitudes are within 10.Similarly, balancing
load among distribution feeders will also lower losses assuming similar conductor resistance.
This may require installing additional switches between feeders to allow for appropriate load
transfer.

Bifurcation of feeders according to Voltage regulation and Load.

7. Load Factor Effect on Losses

Power consumption of customer varies throughout the day and over seasons.

Residential customers generally draw their highest power demand in the evening hours. Same
commercial customer load generally peak in the early afternoon. Because current level (hence,
load) is the primary driver in distribution power losses, keeping power consumption more level
throughout the day will lower peak power loss and overall energy losses.

Load variation is Called load factor and It varies from 0 to 1.

Load Factor = Average load in a specified time period / peak load during that time period.

For example, for 30 days month (720 hours) peak Load of the feeder is 10 MW. If the feeder
supplied a total energy of 5,000 MWH, the load factor for that month is (5,000 MWh)/ (10MW x
720) =0.69.

Lower power and energy losses are reduced by raising the load factor, which, evens out feeder
demand variation throughout the feeder.

The load factor has been increase by offering customers “time-of-use” rates. Companies use
pricing power to influence consumers to shift electric-intensive activities during off-peak times
(such as, electric water and space heating, air conditioning, irrigating, and pool filter pumping).

With financial incentives, some electric customers are also allowing utilities to interrupt large
electric loads remotely through radio frequency or power line carrier during periods of peak use.
Utilities can try to design in higher load factors by running the same feeders through residential
and commercial areas.

8. Transformer Sizing and Selection

Advertisement
Distribution transformers use copper conductor windings to induce a magnetic field into a grain-
oriented silicon steel core. Therefore, transformers have both load losses and no-load core
losses.

Transformer copper losses vary with load based on the resistive power loss equation (P loss =
I2R). For some utilities, economic transformer loading means loading distribution transformers to
capacity-or slightly above capacity for a short time-in an effort to minimize capital costs and still
maintain long transformer life.

However, since peak generation is usually the most expensive, total cost of ownership (TCO)
studies should take into account the cost of peak transformer losses. Increasing distribution
transformer capacity during peak by one size will often result in lower total peak power
dissipation-more so if it is overloaded.

Transformer no-load excitation loss (iron loss) occurs from a changing magnetic field in the
transformer core whenever it is energized. Core loss varies slightly with voltage but is essentially
considered constant. Fixed iron loss depends on transformer core design and steel lamination
molecular structure. Improved manufacturing of steel cores and introducing amorphous metals
(such as metallic glass) have reduced core losses.

9. Balancing 3 phase loads

Balancing 3-phase loads periodically throughout a network can reduce losses significantly. It can
be done relatively easily on overhead networks and consequently offers considerable scope for
cost effective loss reduction, given suitable incentives.

10. Switching off transformers

One method of reducing fixed losses is to switch off transformers in periods of low demand. If
two transformers of a certain size are required at a substation during peak periods, only one
might be required during times of low demand so that the other transformer might be switched
off in order to reduce fixed losses.

This will produce some offsetting increase in variable losses and might affect security and
quality of supply as well as the operational condition of the transformer itself. However, these
trade-offs will not be explored and optimized unless the cost of losses are taken into account.

11. Other Reasons for Technical Losses

 Unequal load distribution among three phases in L.T system causing high neutral
currents.
 leaking and loss of power
 Over loading of lines.
 Abnormal operating conditions at which power and distribution transformers are
operated
 Low voltages at consumer terminals causing higher drawl of currents by inductive loads.
 Poor quality of equipment used in agricultural pumping in rural areas, cooler air-
conditioners and industrial loads in urban areas.