DS-3E1105P-EI/M

4 Port Fast Ethernet Smart PoE Switch

Smart managed switches are developed by Hikvision, featuring easy management and maintenance. You can easily deploy,
monitor and expand your surveillance system anytime and anywhere with our software platforms. You can view the network
topology, monitor the health of the network and receive device alarms in real time, which greatly reduces the cost of
network operation and maintenance.

 4 × 10/100 Mbps PoE port,1 × 10/100 Mbps RJ45 port

 Total PoE Power Budget 45W
 Support 802.1Q VLAN
 Support PoE watchdog to detect and restart the cameras that do not respond
 Support STP/RSTP Loop prevention
 Support cable detection to locate failure
 Up to 300 m Long Range PoE Transmission
 6 kV Surge Protection

Specification
General
Shell Metal material, fan-free design
Net Weight 0.26 kg (0.573 lb)
Gross Weight 0.75 kg (1.65 lb)
Dimensions (W × H × D) 121.1 mm × 27.6 mm × 83.1 mm (4.77'' × 1.09'' × 3.27'')
Operating Temperature 0 °C to 40 °C (32 °F to 104 °F)
Storage Temperature -40 °C to 85 °C (-40 °F to 185 °F)
Operating Humidity 5% to 95% (no condensation)
Relative Humidity 5% to 95% (no condensation)
Power Supply 54 V DC, 0.92 A
Installation Mode Desk-Mounted,Wall-Mounted
Max. Power Consumption 50 W
Power Consumption in Idle 5W
Surge Protection 6 kV
Network Parameters
Ports 4 × 10/100 Mbps PoE port,1 × 10/100 Mbps RJ45 port
MAC Address Table 2K
Switching Capacity 1.2 Gbps
Packet Forwarding Rate 0.89 Mpps
Internal Cache 768 Kbits
PoE Power Supply
PoE Standard IEEE 802.3af,IEEE 802.3at
PoE Power Pin 8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
PoE Port PoE: Ports 1 to 4
Max. Port Power 30 W
PoE Power Budget 45 W
Software Function
Ports 1 to 4: port isolation mode to improve network security
Port Isolation Ports in an isolation group cannot communicate with each other, but they can
communicate with ports outside the isolation group.
PoE Watchdog Ports 1 to 4: auto detect and restart the cameras that do not respond.
Link aggregation is used to aggregate multiple physical ports to form a logical port for
load balancing, bandwidth expansion, and port protection.
Link Aggregation
Support static link aggregation.
Support 1 aggregation group.
Loop prevention is used to prevent the switching network from forming loops, which
will seriously affect network communication. Disabled by default.
Loop Prevention
Support 802.1D STP.
Suppport 802.1w RSTP.
VLAN is used for network scale planning and network health improvement.
Support 802.1Q.
VLAN Configurable VLAN ID from 1-4094.
Support Trunk, Access port mode.
Support Max. 32 VLAN.
 Ports 1 to 4: up to 300 m.
Long Range
Long range performance may vary depend on camera model or cable condition.
Support one-click activation and remote management via Hik-Partner Pro. Functions
supported:
1. Display the port rate.
2. Display the port bandwidth utilization rate.
3. Display the PoE power usage.
HPP
4. Display topology information.
5. Display the alarm status.
6. Restart ports and devices.
7. Enable port long-rage mode.
8. Remotely upgrade the device.
System Maintenance Support remote management via Hik-Partner Pro.
Ports 1 to 2: data on VIP ports is preferentially forwarded when bandwidth resources
VIP Port
are insufficient.
Approval
CE-EMC (EN 55032: 2015+A11: 2020, EN IEC 61000-3-2: 2019, EN 61000-3-3: 2013+A1:
EMC
2019, EN 50130-4: 2011+A1: 2014, EN 55035: 2017+A11: 2020)
CB (AMD1:2009, AMD2:2013, IEC 62368-1: 2014 (Second Edition), CE-LVD (EN
Safety
62368-1: 2014+A11: 2017)
Chemistry CE-RoHS (2011/65/EU),WEEE (2012/19/EU),Reach (Regulation (EC) No.1907/2006)


Available Model
DS-3E1105P-EI/M
DS-3E1105P-EI/M V2


Typical Application

Physical Interface
Front Panel

Rear Panel

No. Indicator/Port Description

 Solid on: The switch is powered on normally.
① PWR Indicator
 Unlit: No power supply is connected or power supply is abnormal.
 Solid on/Flashing: The output power of the switch is about to reach or has reached the
upper limit. The power supply may be abnormal if more devices are connected.
PoE-MAX
②  Unlit: The switch does not supply power to a powered device (PD), or supplies power to a
Indicator
PD normally and its output power does not reach the upper limit.（About 5 seconds after the
output power of the switch returns to normal, the PoE-MAX indicator will be unlit.）
 Solid on: The port is connected.
LINK/ACT
③  Flashing: The port is transmitting data.
Indicator
 Unlit: The port is disconnected or connection is abnormal.
 Solid on: The switch supplies power to a PD normally.
④ PoE Indicator
 Unlit: The switch is disconnected from a PD or power supply is abnormal.
10/100 Mbps PoE
⑤ Used for connection to a PD via a network cable.
RJ45 Port
10/100 Mbps RJ45
⑥ Used for connection to another device via a network cable.
Port
⑦ Reset Button Used for restoring all the configurations of the switch to the default settings.
Grounding
⑧ Used for connection to the grounding cable to protect the switch from lightning.
Terminal
⑨ Power Supply Use the attached power cord and power adapter to connect the switch to a socket.

Dimension