Installation and configuration manual
With Voltronic
Pytes Lithium Battery
E-BOX Series
With Voltronic Axpert King Inverter
CONTENTS
1.BOM List ................................................................................ 3
2.Communication Cable ........................................................... 4
3.How to Install ......................................................................... 5
4.Power Cable Connection ........................................................ 6
Step.1 ..................................................................................................... 6
Step.2 ..................................................................................................... 6
Step.3 ..................................................................................................... 6
5.Communication Cable Connection ........................................ 7
Step.1 ..................................................................................................... 7
Step.2 ..................................................................................................... 8
6.Set the DIP Switch................................................................. 9
7.Start Up the System ............................................................ 10
8.Change the Battery Setting of The Inverter ...................... 10
9.Warning Message 61. How to Reset It ................................ 11
2
1.BOM List
Before installation, you should prepare following items as shown in
Graph 1.
Item Remarks Quantity
Conductor cross-section: 50 mm²to
95 mm²
Cable diameters: 14 mm to 25 mm Depends on the number of
Power Cable
Only copper cables may be used. batteries and the
(DC)
The DC cables must be sized for the connection method
maximum battery voltage and the
maximum battery current.
RS485 communicationTerminal
RJ45 Cable (RJ45 port) follow RS485 protocol, to 1
output batteries information.
PC (Personal
Self-Provide. 1
Computer)
Depends on the number of
Battery 48100R / 48100C / 4850 batteries and the
connection method
Inverter Voltronic Axpert King 1
Graph 1.
3
2. Communication Cable
RJ45 Port cable configuration for BMS and Inverter is shown in Pic 2.1.
and Pic 2.2.
Pic 2.1
Pic 2.2
4
3. How to Install
Install the system as shown in Flow Chart 1.
Communication cable
Power cable connection
connection
Start up the system Set the DIP switch
change the battery
Check the battery SOC
setting of the inverter
System monitoring
Flow Chart 1.
CAUTION: If you want to get more inverter-related settings, please refer to
the inverter user manual first.
5
4. Power Cable Connection
Step.1
Before connecting all wirings, please take off bottom cover by
removing two screws as shown Pic 4.1.
Pic 4.1
Step.2
Connect the red and black cables to the inverter DC connector as
shown in Pic 4.2.
BATTERY+
BATTERY-
Pic 4.2
Step.3
At the other end of the cable, connect to the battery as shown Pic 4.3.
6
（Ensure that the battery power switch is off）
Pic 4.3
5. Communication Cable Connection
Step.1: Wire Set Up
a): Prepare one cable, one clamp and one scissor as shown in Pic
5.1.1.
Pic 5.1.1
b): Cut the cable skin at both ends to expose the wires as shown in Pic
5.1.2.
Pic 5.1.2
7
c): Arrange wires sequence according to the Appendix C V1.0.4.
d): Check the battery wire sequence
e): Insert battery wire lines and inverter wire lines respectively into
crystal heads.
f): Clamp two crystal heads tightly and take them out as shown in Pic
5.1.3.
Pic 5.1.3
Step.2: Cable Connection
Connect one end of the cable to the inverter communication port as
shown in Pic 5.2.1. Make sure which communication port to use.
8
RS485
Pic 5.2.1
Connect the other end of the cable to the battery communication port
as shown in Pic 5.2.2 (Ensure the correct sequence of wires inside the
communication cable).
Pic 5.2.2
6. Set the DIP Switch
Set the 1st dip-switch up and the rest of the switches down. Only the
master battery requires the dip switches adjusted (Up, Down, Down, Down)
as shown in Pic 6.1
9
Pic 6.1
7. Start Up the System
Start up the inverters and batteries.
8. Change the Battery Setting of The Inverter
※CAUTION: If you want more details about the batteries settings，
please check the operating manual of inverters.
You have to navigate to menu 05 (press enter button for 3 seconds to
enter the menu) of the off grid inverter and select the option PYL. When
you find PYL press enter and then return to the main menu (press return
button to top left corner of the LCD) as shown in Pic 8.1 and Pic 8.2
10
Pic 8.1
Pic 8.2
END
11
