Mar.
2019
UMEGUARD SX No. 6166G
（UG SX）
UMEGUARD SX, surface tolerant paint, is a epoxy type paint.
It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc.
and chemical resistance to water, salt water and crude oil.
TECHNICAL DATA
Type Epoxy paint
RecommendedUse Inside and outside of accommodation space, void space, cofferdam, engine room,
pipe line, other steel structures, etc.
Information Mixing Ratio : Base : Hardener = 85 : 15 [by volume]
Color : White, Black, Grey, etc
Flash Point : Base = 23.5, Hardener = 19.0 [˚C]
Density : 1.34 [g/mL] (ISO:2811)
Volume solids (VS) : 57(+/-2) [volume %] (ISO:3233)
VOC : 432 [g/L] (Method24)
Coverage(Theoretical): 0.132 - 0.351 [L/m2]
Film Thickness : WET 132 - 351 [microns]
DRY 75 - 200 [microns]
o o o o
5 C 10 C 20 C 30 C
Drying Time Set-to-touch 4.5hrs. 3.5hrs. 2.5hrs. 1.5hrs.
Hard Dry 44hrs. 27hrs. 17hrs. 12hrs.
Painting Interval Min 44hrs. 27hrs. 17hrs. 12hrs.
Max * - - - -
Pot Life 24hrs. 14hrs. 8hrs. 5hrs.
Condition Method of Application : Airless spray, Brush, Roller
of Weather : Temperature:Minimum 5 ˚C, Humidity:Maximum 85 %RH, Dew
Application Point +Minimum 3 degC
For Airless Spray : Viscosity : 1.5 - 2.0Pa･s
Tip No. : (GRACO)419 - 623
Paint Output Pressure: 14.7 - 17.7[MPa]
Spray Speed : 60 - 80[cm/sec]
Thinner : EPOXY THINNER A,
Thinning: 0 - 15 % by Volume
Preceding Coats : NZ PRIMER S, CERABOND 2000, EPICON ZINC RICH PRIMER B-2
Subsequent Coats : EPICON FINISH HB，ACRI 700 FINISH ST, etc
Packaging Two pack product
Notes *: Kindly consult with CMP sales office.
1.In case that thick film application is required, please apply N6, N7 or Red brown color
product.
2.Ventilation shall be maintained from coating application until the completion of curing in order
to remove residue of solvents and promote curing.
3.Agitate Base with a power agitator until it is turned homogeneous, and then combine entire
contents of Hardener with Base and mix thoroughly with power agitator.
4.Excessive thinning results in reduced sag resistance and paint film property.
5.*If there is a possibility that the painted surface will be in direct sunlight, the succeeding
coat should be applied, as soon as possible after the minimum painting interval.
6.In common with all epoxy coatings, UMEGUARD SX will show chalking and fading on
exposure to UV light.
7.Density, VS and VOC are measured from product samples without thinning. Values may vary
depending on color, manufacturing process, local regulations, etc.
This product should be used only by professional applicators. Consult the current Chugoku Marine Paints Safety Data Sheets. Follow all local
or national health, safety and environmental regulations. Observe all safety labels on packaging and containers. Take precautions against
possible risks of fire or explosions as well as protection of the environment. Apply only at ventilated areas. Handle with care.
This data sheet contains the best and latest of our knowledge on the date of issue on our laboratory test in Japan and practical application
experience, and subject to change without notice. Since the paints are used under unexpected circumstances in some cases, guarantee can
not be given except on the quality of those paints themselves.
