DETAILED ESTIMATE FOR WIRE FENCING

Based on Rajasthan RUIDP ISOR 2023

Sl SOR Description No. L B H/D Qty Unit
.
1 4.10' Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms,
including getting out the excavated

4.10.1 In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc.

4.10.1.1 Depth upto 1.5 m 4 0.6 0.6 1 1.44 cum

Providing 1.20 metre high fencing with angle iron posts 50 mm x 50 mm x 6 mm at 3 metre center to center
with 0.40 metre embedded in M15 grade cement concrete, corner, end and every 10th post to be strutted,
1 200 200 mtr
provided with welded steel wire fabric of 75 mm x 50 mm mesh or 75 mm x 25 mm mesh and fixed to iron
2 10.19 posts by flat iron 50 x 5 mm and bolts etc. complete in all respects including all material, labour.

3 Providing and laying in position cement concrete of specified grade excluding the cost of centring and
21.1 shuttering -
All work upto plinth level

21.1.7 1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size). 4 0.6 0.6 0.15 0.22 Cum

4 24.1 Brick work with FPS bricks of class designation 75 in foundationand plinth in:

24.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 4 0.6 0.6 1 1.44 Cum

5 24.5.2 Brick work with FPS bricks of class designation 75 in superstructure above plinth level upto two stories in all
4 0.45 0.45 1.5 1.22 Cum
shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

6 32.1.1 Cement plastering including T&P, scaffolding, material and complete labpour, including cost of water, curing,
racking of joints etc. with 12 mm cement plaster of mix :
1:6 (1 cement : 6 fine/ coarse sand) 4 1.8 1.5 10.8 Sqm

1 4.3 Earth work in excavation in soil unsuitable for road construction such as marshy soil including
pumping
out water, removal of the same and disposal with all lift and lead upto 1 km as per MoRT&H 1 311 7.5 0.2 466.5 cum
specification clause 301.

Providing, laying, spreading and compacting of granular sub-base by providing close graded
Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site,
spreading in uniform layers with motor grader on prepared surface and compacting with vibratory
1 311 7.5 0.15 349.88 cum
power roller to achieve the desired density, complete as per MoRT&H
specification clause - 401 including all material, labour, machinery, lighting, guarding and
2 7.1.1 maintenance of diversion. Grading
 Providing, laying, spreading (with paver finisher only) and compacting wet mix macadam (WMM)
base course comprising of graded stone aggregate and granular material conforming to MORT&H
specifications (Table 400-II) in layers of equal compacted thickness each consolidated, including
premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed aterial
1 311 6.5 0.1 202.15 Cum
by tippers to site, laying in uniform layers in base course on a well prepared sub-base/ base course
and compacting with power vibratory-roller to achieve the desired density complete as per oRT&H
specification clause - 406 including all material, labour, machinery, lighting, guarding and
3 7.6 maintenance of diversion.

Providing and applying tack coat on the prepared surface with bitumen emulsion as per IS: 8887 and
approved quality @ 0.2 kg/sqm with the help of spray set fitted on bitumen Container (boiler) fter 1 311 5.5 1710.5 Sqm 8
Sl. SOR Description No. L B H/D Qty Unit
5 8.3 approved quality @ 0.2 kg/sqm with the help of spray set fitted on bitumen Container (boiler) fter 1 311 5.5 1710.5 Sqm
cleaning the surface with brooms or soft brushes and finally dusting with old gunny bags and
compressed

Providing and laying 30-45 mm compacted thickness Bituminous Concrete as per design mix (approved
by Engineer) on prepared surface with specified grade stone aggregate as per Table - 500-18 with
bitumen for wearing course including loading of aggregate with F.E. loader and hot mixing of stone
aggregate and bitumen (including Cost of anti stripping compound Minimum 1% in Lime/Cement as per
design wherever required) in computerised hot mix plant, transporting the mixed material by tippers to
paver and laying with paver finisher fitted with electronic sensing device (as per clause 5043.5) to the
required level and grade and compacting by power rollers and vibratory rollers or 150 to 250 KN
pneumatic tyred roller with TP = 0.7 Mpa, to achieve the desired density complete as per clause 509 of
MoRT&H specification including all material, labour, machinery, lighting, guarding and maintenance of
diversion but excluding primer/tack coat.
6 8.10 '
7 8.10.1 Grade-II with Bitumen VG-grade 30 @ 6% (percent by weight of total mix) 1 311 5.5 0.05 85.53 cum

Construction of subgrade and earthen shoulders with approved material obtained from borrow area with
all lifts & leads, transporting to site, spreading, grading to required slope and compacted in layers not
exceeding 200mm thickness at OMC, with vibratory roller of 80- 100 KN static weight or more to attain
2 311 1 0.075 46.65 cum
a density 97% maximum dry density to meet requirement of table No. 300-2 as per MoRT&H

8 4.6 specification clause 305. (Lead taken upto 5 km)

Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of
bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal
1 4.1
of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following
depths, below natural ground / Road top level.
4.10.1
In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc.
 4.10.1.1 Depth upto 1.5 m 1 250 0.43 0.45 48.38 Cum
Providing and laying in position cement concrete of specified grade excluding the cost of centring and
2 21.1
shuttering - All work upto plinth level
21.1.7 1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size). 1 250 0.43 0.1 10.75 Cum
3 24.1 Brick work with FPS bricks of class designation 75 in foundationand plinth in:
24.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) 2 250 0.115 0.115 6.61 Cum
Cement plastering including T&P, scaffolding, material and complete labour, including cost of water, curing,
4 32.1.
racking of joints etc. with 12 mm cement plaster of mix :
32.1.1 1:4 (1 cement : 4 fine/ coarse sand)
Side Wall 2 250 0.47 232.5 Sqm
Sl. SOR Description No. L B H/D Qty Unit

Constructing masonry Chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar
1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160 mm bottom
diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4
graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5
fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1
cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard
design :
5 34.31
34.31.1 With F.P.S. bricks 2 2 Each

Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of
bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal
of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following
1 4.10' depths, below natural ground / Road top level.
4.10.1
In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc.
4.10.1.1 Depth upto 1.5 m 8 0.9 0.9 1.2 7.78 cum
2 21.1.5 Providing and laying in position cement concrete of specified grade excluding the cost of centring and
shuttering - All work upto plinth level : 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 8 1.1 1.1 0.1 0.97 Cum
mm nominal size).
3 23.3.3 M-25 Grade Concrete (1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) -
3.12 Cum
As per design mix)
Base 8 1 1 0.3 2.4 Cum
Column 8 0.3 0.3 1 0.72 Cum
Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position
4 23.19.6
and binding all complete. Thermo-Mechanically Treated bars.
306.15 kg

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including
8 29.2
cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:
1136.52 kg
 Column 122x61x4.5 8 2.7 12 259.2
Rafter 122x61x4.5 4 5.5 12 264
Trasverse Member 50x50x2.9 2 15 4.25 127.5
Purline Member 50x50x2.9 6 15 4.25 382.5
10 % Extra For Plate and Bolts 103.32
Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J
or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet
washers filled with white lead and including a coat of approved steel primer and two coats of approved
paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces)
excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever
9 31.1 required.
31.1.3 0.63 mm thick with zinc coating not less than 275gm/m² 1 15 5.5 82.5 Sqm
Sl. SOR Description No. L B H/D Qty Unit
Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of
bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal
1 4.10'
of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following
depths, below natural ground / Road top level.
4.10.1
In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc.
4.10.1.1 Depth upto 1.5 m 24 cum
Colummn Base 20 1 1 1.2 24
Providing and laying in position cement concrete of specified grade excluding the cost of centring and
2 21.1.5 shuttering - All work upto plinth level : 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 2 Cum
mm nominal size).
Colummn Base 20 1 1 0.1 2
M-25 Grade Concrete (1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) -
3 23.3.3 5.72 Cum
As per design mix)
Base 20 0.75 0.75 0.3 3.38 Cum
Column 20 0.3 0.3 1.3 2.34 Cum
Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position
4 23.19.6
and binding all complete. Thermo-Mechanically Treated bars.
560.78 kg

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including
5 29.2
cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:
8340.56 kg

Column 63X63X3.6 20 2.4 6.51 312.48

Bottem Cord 63X63X3.2 10 9 5.85 526.5
Top Cord 63X63X3.2 10 9.22 5.85 539.34
Trasverse Member 75X75X4.9 2 45 10.3 927
Inclined Member 40.0X40.0X3.2 10 1 3.49 34.9
 VerticleMember 40.0X40.0X3.2 12 0.43 3.49 18.01
Purline Member 75X75X4.9 11 45 10.3 5098.5
Base Plate 200x200x10 20 3.14 62.8
Cap Plate 200x200x10 20 3.14 62.8
10 % Extra For stiffner, Bolts & waste 758.23
Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J
or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet
washers filled with white lead and including a coat of approved steel primer and two coats of approved
paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces)
excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever
6 31.1 required.
31.1.1 1.00 mm thick with zinc coating not less than 275gm/m² 2 45 4.6 414.88 Sqm
1 24.1 Brick work with FPS bricks of class designation 75 in foundationand plinth in:
Sl. SOR Description No. L B H/D Qty Unit
24.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand) 1 250 0.23 0.6 34.5 Cum
2 32.1.1 Cement plastering including T&P, scaffolding, material and complete labpour, including cost of water,
curing, racking of joints etc. with 12 mm cement plaster of mix :
32.1.1.1 1:6 (1 cement : 6 fine/ coarse sand) 1 250 0.3 75 Sqm
Earth filling with available surplus soil excavated from foundations and taken only from outside of
3 4.13 building plinth in layers not exceeding 20cm in depth, consolidating each deposited layer including 192 Cum
ramming and watering and consolidation with lead up to 50 m and lift upto 1.5 m.
Tipping Area 1 10 15 0.1 15
MRF 1 15 32 0.1 48
Refining Area 1 5 15 0.1 7.5
Composting Pad 1 45 27 0.1 121.5
4 30.35 Random rubble dry stone Kharanja (soling) under floor. 192 Cum
Tipping Area 1 10 15 0.1 15
MRF 1 15 32 0.1 48
Refining Area 1 5 15 0.1 7.5
Composting Pad 1 45 27 0.1 121.5
Providing and laying in position cement concrete of specified grade excluding the cost of centring and
5 21.1
shuttering - All work upto plinth level :
21.1.2 1:1½:3 (1 Cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size). 151.5 Cum
Tipping Area 1 10 15 0.15 22.5
Refining Area 1 5 15 0.1 7.5
Composting Pad 1 45 27 0.1 121.5
M-25 Grade Concrete (1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) -
6 23.3.3 72 Cum
 As per design mix)
MRF 1 15 32 0.15 72 Cum
7 24.5.2 Brick work with FPS bricks of class designation 75 in superstructure above plinth level upto two stories
122.03 Cum
in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)
Outer Wall 1 100 4.4 0.23 101.2
Partition Wall 1 1 20.27 3 0.115 6.99
Partition Wall 2 1 40.1 3 0.115 13.83
8 32.1.1 Cement plastering including T&P, scaffolding, material and complete labpour, including cost of water,
curing, racking of joints etc. with 12 mm cement plaster of mix :
1:6 (1 cement : 6 fine/ coarse sand) 1279.11 Sqm
Outer Wall 2 100 4.515 903
2 20.3 3.115 126.28
2 40.1 3.115 249.82
9 32.15 Providing and applying plaster of paris putty of 2 mm thickness over 1279.11 Sqm
Sl. SOR Description No. L B H/D Qty Unit
Earth work in excavation in open area, STP, WTP, Pumping station with mechanical means including
dressing of sides and ramming of bottoms, including getting out the excavated material, disposal of
excavated material lead upto 1000m at suitable site as per as per drawing and as per direction of
1 4.9.1.1 Engineer. (Measurements for payment to be done as per standard drawings).
4.9.1 In all kind of soil
4.9.1.1 Upto 3.0 m depth 1 8 8 0.3 19.2 Cum
2 39.47 Providing & laying synthetic clay liner in excavated trench. 1 8 8 64 Sqm

Earth filling with available surplus soil excavated from foundations and taken only from outside of
3 4.13 building plinth in layers not exceeding 20cm in depth, consolidating each deposited layer including 1 8 8 0.3 19.2 Cum
ramming and watering and consolidation with lead up to 50 m and lift upto 1.5 m.

Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms,
including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus
excavated material at a lead upto 50m suitable site as per direction of Engineer for following depths, below
natural ground / Road top level.
1 4.10 '
4.10.1
In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc.

4.10.1.1 Depth upto 1.5 m 20 1.7 1.7 1.5 86.7 cum

Providing and laying in position cement concrete of specified grade excluding the cost of centring and
3 21.1.5 shuttering - All work upto plinth level : 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm 20 1.7 1.7 0.1 5.78 Cum
nominal size).
M-25 Grade Concrete (1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) -As
4 23.3.3
per design mix)
52.11 Cum
 Base 20 1.5 1.5 0.45 20.25 Cum
Column 20 0.3 0.3 6.6 11.88 Cum
Plinth Beam 1 0.3 0.3 94 8.46 Cum
Mid Beam 1 0.3 0.3 64 5.76 Cum
Top Beam 1 0.3 0.3 64 5.76 Cum
Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position and
5 23.19.6
binding all complete. Thermo-Mechanically Treated bars.
4090.64 kg

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting,
10 29.2
hoisting, fixing in position and applying a priming coat of approved steel primer all complete:
11329.56 kg

Bottem Cord 100X100X6 16 7.62 16.7 2036.33

Top Cord 100X100X6 16 7.62 16.7 2036.33
Bracings Member 100X100X6 24 6.09 16.7 2440.47
Inclined Member 100X100X6 20 1.16 16.7 387.44
VerticleMember 100X100X6 21 0.75 16.7 263.03
Sl. SOR Description No. L B H/D Qty Unit
Purline Member 100X100X6 14 32 7 3136
10 % Extra For Plate, Bolts waste 1029.96
Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with
polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I.
limpet washers

or with G.I. limpet washers filled with white lead and including a coat of approved
steel primer and two coats of approved paint on overlapping of sheets complete upto
any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins,
rafters and trusses and including cutting to size and shape wherever required.
13 31.1
31.1.1 1.00 mm thick with zinc coating not less than 275gm/m² 2 32 7.6 487.74 Sqm

Earth work in excavation in open area, STP, WTP, Pumping station with mechanical means
including dressing of sides and ramming of bottoms, including getting out the excavated
material, disposal of excavated material lead upto 1000m at suitable site as per as per drawing
and as per direction of Engineer. (Measurements for payment to
1 4.9.1.1
4.9.1 In all kind of soil
4.9.1.1 Upto 3.0 m depth 1 3 3 2 18 Cum
2 21.1 Providing and laying in position cement concrete of specified grade excluding the cost of centring and
shuttering - All work
upto plinth level :
 21.1.5 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). 1 3 3 0.1 0.9 Cum
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth
and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto two stories
2 3 3 0.1 1.8 Cum
excluding cost of centring, shuttering, finishing and reinforcement : 1:1½:3 (1 cement : 1½ coarse sand :
3 23.2.2 3 graded stone aggregate 20 mm nominal size )
Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position
4 23.19.6
and binding all complete. Thermo-Mechanically Treated bars.
105.98 kg

5 24.5.2 Brick work with FPS bricks of class designation 75 in superstructure above plinth level upto two stories
1 12 0.23 2 5.52 Cum
in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)
Cement plastering including T&P, scaffolding, material and complete labpour, including cost of water,
6 32.1.1
curing, racking of joints etc. with 12 mm cement plaster of mix :
1:6 (1 cement : 6 fine/ coarse sand) 9 Sqm
Side 1 3 3 9
8 32.9 Neat cement punning 1 5 5 25 Sqm
Sl. SOR Description No. L B H/D Qty Unit
9 29.2
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including
5 kg
cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:

Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming
of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation
and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of
Engineer for following depths, below natural ground / Road top level.
1 4.1
4.10.1 In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil,
kankar, etc.
4.10.1.1 Depth upto 1.5 m 1 14 0.9 1.2 15.12 Cum
Providing and laying in position cement concrete of specified grade excluding the cost of
3 21.1
centring and shuttering - All work upto plinth level
21.1.7
1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size). 1.26 Cum

F1 1 14 0.9 0.1 1.26 Cum

4 24.1 Brick work with FPS bricks of class designation 75 in foundationand plinth in:
24.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand) 9.63 Cum
Step 1 1 14 0.75 0.45 4.73 Cum
Step 2 1 14 0.6 0.45 3.78 Cum
Step 3 1 14 0.4 0.2 1.12 Cum
 Earth filling with available surplus soil excavated from foundations and taken only from
outside of building plinth in layers not exceeding 20cm in depth, consolidating each deposited
5 4.13 12.24 Cum
layer including ramming and watering and consolidation with lead up to 50 m and lift upto 1.5
m.

Centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre
6 22.1
above plinth level including strutting, propping etc. and removal of form for

22.1.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. 16.8 Sqm
Lintel Beam 1 14 0.6 8.4 Sqm
Plinth Beam 1 14 0.6 8.4 Sqm
Centring and shuttering with plywood or steel sheet upto two stories or height upto 7.5 metre above
7 22.1
plinth level including strutting, propping etc. and removal of form for
22.1.3 Suspended floors, roofs, landings, balconies and access platform. 13.2 Sqm
Slab 1 1 4 3 12
Projection 2 2 0.3 1.2
Sl. SOR Description No. L B H/D Qty Unit
Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings,
8 23.3 balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto two
stories excluding the cost of centring, shuttering, finishing and reinforcement:
23.3.2 M-20 Grade Concrete (1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal
3.88 Cum
size) -As per design mix)
Lintel Beam 1 14 0.3 0.23 0.97 Cum
Plinth Beam 1 14 0.3 0.3 1.26 Cum
Slab 1 4 3 0.125 1.5 Cum
Projection 2 2 0.3 0.125 0.15 Cum
Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position
9 23.19.6
and binding all complete. Thermo-Mechanically Treated bars.
304.27 kg

10 30.35 Random rubble dry stone Kharanja (soling) under floor. 1 3.5 2.5 0.1 0.9 Cum
11 21.1 Providing and laying in position cement concrete of specified grade excluding the cost of centring and
shuttering - All work upto plinth level
21.1.7 1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size). 1 3.5 2.5 0.1 0.9 Cum
Providing and fixing 1st quality ceramic glazed vitrified tiles of colour standard white, grey, ivory, fume,
red brown, light green, light blue, and other light shades with water absorption less than or equal to
0.08% confirming to IS : 13753 & IS : 15622 in floor, steps etc laid on bed on neat cement slurry
finished with flush pointing in the white cement mixed with pigment to match the shade of the tile
12 27.18 complete (excluding the cost of cement plaster on wall and pillar)
27.18.1 Size 600mm x 600mm 8.99 Sqm
 Flooring 1 1 3.5 2.5 8.99 Sqm
Skrting 1 14 0.075 1.05 Sqm
Brick work with FPS bricks of class designation 75 in superstructure above plinth level upto two stories
13 24.5.2
in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)
8.62 Cum

Parapet wall 1 14 0.3 0.23 0.97 Cum

Wall 1 14 2.8 0.23 9.02 Cum
Deduction
Door D1 1 1.8 2.1 0.23 0.87 Cum
Window W1 2 0.9 1.2 0.23 0.5 Cum
Cement plastering including T&P, scaffolding, material and complete labpour, including cost of water,
14 32.1.1
curing, racking of joints etc. with 12 mm cement plaster of mix :
1:6 (1 cement : 6 fine/ coarse sand) 31.86 Sqm
Inner wall 1 14 2.7 37.8 Sqm
Deduction
Door D1 1 1.8 2.1 3.78 Sqm
Window W1 2 0.9 1.2 2.16 Sqm
Sl. SOR Description No. L B H/D Qty Unit
Cement plastering including T&P, scaffolding, material and complete labour, including cost of water,
curing, racking of joints etc. with 6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a
15 32.8
floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C.
1 4 3 12 Sqm
slabs and beams.
16 32.3 Cement plastering including T&P, scaffolding, material and complete labour, including cost of water,
curing, racking of joints etc. with 20 mm cement plaster of mix :
32.3.3 1:6 (1 cement : 6 fine/ coarse sand) 58.46 Sqm
Parapet wall 2 14 0.3 8.4 Sqm
Wall 1 14 4 56 Sqm
17 32.15 Providing and applying plaster of paris putty of 2 mm thickness over 102.32 Sqm
18 32.32 plastered surface to prepare the surface even and smooth Applying one coat of cement primer of
approved brand and manufacture on wall surface :
32.32.1 Cement primer. 102.32 Sqm
19 32.31
Distempering with 1st quality acrylic washable distemper (ready mixed) of approved manufacturer and
of required shade and colour complete. as per manufacturer's specification. .
32.31.1 Two or more coats on new work 102.32 Sqm
20 31.62. Grading roof for water proofing treatment with water proofing compound
31.62.1
Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 1 4 3 0.1 1.2 Cum

21 31.21 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm
and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard
 design :
31.21.1 In 75x75mm deep chase 1 14 14 mtr
Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with
water proofing cement compound consisting of applying : a) after surface preparation, first layer of
slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. b)
laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibr cloth
should not be less than 10 cm. c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289
kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm.
This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment
will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. d) fourth and final
layer of brick tiling with cement mortar (which will be paid for separately For the purpose of
measurement the entire treated surface will be measured. 1 4 3 12 Sqm
22 38.6
Sl. SOR Description No. L B H/D Qty Unit
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built
up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to
IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold
fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required
PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed
mechanically wherever required including cleat angle, Aluminium snap beading for lazing / panelling,
C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of
23 37.1 Engineer-in-charge. (Glazing and panelling to be paid for separately) :
37.1.1 For fixed portion.
37.1.1.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum
75 kg
anodic coating of grade AC 15)
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with
24 37.3. PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of
engineerincharge . (Cost of aluminium snap beading shall be paid in basic item) :
37.3.1 With float glass panes of 4.0 mm thickness 5.94 sqm
Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315
marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with
25 37.4.
brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of
Engineer-in-charge.
37.4.1 With stainless steel cover plate 3 Each
26 32.50.
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :
32.50.1. Two or more coats on new work 5.94 Sqm
Total