MC-Injekt 2300 top
Flexible Sealing
Injection Resin
Product Properties
• Very low-viscous, polyurethane-based elastomer resin
• Very good injection properties
• High reactivity
• Controlled pore formation with limited increase in volume
• High flexibility, watertight
• Fulfils UBA-guideline for sealing in contact with drinking water
• Declaration of Performance according to EN 1504-5: U(D1) W(1) (1/2/3/4) (6/35)
Areas of Application
• Flexible sealing and filling of cracks, joints and voids in building construction, underground and
engineering structures under dry, water-bearing and high-pressure water-bearing conditions
• Injection works according to EN 1504
• Injection hoses
• Sealing of potable water structures
• Subsequent horizontal barrier and vertical barrier against rising moisture in masonry
• REACh-assessed exposure scenarios: long-term water contact (crack), periodical inhalation, application
Application
Preparation 2 % related to component A). The catalyst has to
Before injection, the structure, the leaking areas, be added in component A before the two compo-
respectively, have to be inspected according to nents are mixed.
technical standards and regulations, and, injection
concept is to be prepared. Injection
The injection can be executed with the injection
Mixing pump MC-I 510 (1-component pump) or MC-I 700
MC-Injekt 2300 top consists of two components, (2-component pump).
component A and component B. They have to be
mixed according to the recommended ratio using In case of high pressurized water where the accel-
slowly rotating stirrers until the mixture is homo- erated reactivity with MC-KAT 23 is not sufficient
geneous. Before processing, the mixed reactive enough, the elastomer foam MC-Injekt 2033 must
resin has to be repotted into a clean empty con- be pre-injected, so that MC-Injekt 2300 top can
tainer or a container in which only mixed resin of not be washed out before curing. For the injection
the same quality was stored. Repotting is fulfilled MC-Injektionspacker (high-pressure bore packer)
when the resin is poured into the reservoir of an are recommended.
injection pump and re-mixed thoroughly.
Work with MC-Injekt 2300 top must be stopped if
When using a 2-component pump, the two compo- the temperature of the structure drops below
nents are mixed in the mixing head of the pump. + 6 °C. Detailed information on application can be
Premixing is not necessary. found in MC Method Statements for MC-Injekt
2300 top.
The application time depends on the quantity of
the mixed material and the ambient temperature. Machine Cleaning
Within the application time all tools can be clea-
Acceleration of Reactivity ned with MC-Verdünnung PU (MC-Thinner PU).
The reaction of the resin can be accelerated by Partially or completely cured material can only be
adding the catalyst MC-KAT 23 (addition of up to removed mechanically.
햲
MC-Bauchemie • Am Kruppwald 1-8 • 46238 Bottrop • Tel. +49 (0) 20 41-101 10 • Fax: +49 (0) 20 41-101 188
[email protected] • www.mc-bauchemie.de
Technical Data for MC-Injekt 2300 top
Characteristic Unit Value* Comments
Mixing ratio p. b. w. 100 : 111 component A : component B
p. b. v. 1:1 component A : component B
Density kg/dm3 approx. 1.04 DIN 53 479
Viscosity mPa·s approx. 55 DIN EN ISO 3219
Surface tension mN/m approx. 34.651 Krüss Processor Tensiometer K100
Expansion in crack % > 11 - 17 DIN EN 12618-2
Maximum expansion % approx. 100 DIN 53 455
Adhesive tensile strength N/mm² approx. 0.6 DIN EN 12618-1, dry/wet concrete
Expansion ratio with water - approx. 1.04 DIN EN 14406
Glass transition temperature °C approx. - 34 DIN EN 12614
Application time Minutes approx. 35 DIN EN 1504-5
Application temperature °C + 6 to + 35 air, substrate and material
temperature
* All technical values relate to 20 °C and 50 % relative humidity.
Product Characteristics for MC-Injekt 2300 top
Cleaning agent MC-Verdünnung PU (MC-Thinner PU)
Under no circumstances water or water-based cleaning agents
should be used.
Colour Light brown
Delivery Box of 6 x 1 l pack, canister of 10 l and 20 l for each component
MC-KAT 23 in a box of five 400 ml aluminium bottles
Storage Can be stored in original sealed packages at temperatures between
+ 5 °C and + 25 °C in dry conditions for at least 1 year. The same
requirements are valid for transport.
Disposal Packs must be emptied completely.
Safety Advice
Please take notice of the safety information and advice given on the packaging labels and safety data
sheets. GISCODE: PU40
Note: The information on this data sheet is based on our experiences and correct to the best of our knowledge. It is, however, not binding. It has to
be adjusted to the individual structure, application purpose and especially to local conditions. Our data refers to the accepted engineering rules,
which have to be observed during application. This provided we are liable for the correctness of this data within the scope of our terms and conditi-
ons of sale-delivery-and-service. Recommendations of our employees which differ from the data contained in our information sheets are only binding
if given in written form. The accepted engineering rules must be observed at all times.
Edition 02/17. Some technical changes have been made to this print medium. Older editions are invalid and may not be used anymore. If a techni-
cally revised new edition is issued, this edition becomes invalid.
햳
MC-Bauchemie • Am Kruppwald 1-8 • 46238 Bottrop • Tel. +49 (0) 20 41-101 10 • Fax: +49 (0) 20 41-101 188
[email protected] • www.mc-bauchemie.de
