USER MANUAL
WIRELESS HEADSET
AIRLINK 3085 IA
Characteristics
Up to 8 simultaneous connexions
NRR 26 dB / SNR : 32 dB
Advanced Ergonomics
Can be wirelessly connected to Airlink 3085IA
base
Certifications
EN352-1:2002 ; EN352-6 :2002 AS/NZS : Class 5 SLC80 : 30dB 1974
f(Hz) 63 125 125 500 1000 2000 4000 8000
Mf(dB) 19.2 18.4 23.1 32.4 37.3 34.1 41.5 38.2
Sf(dB) 4.3 2.6 2.3 2.8 2.9 2.6 3.0 2.8
APV(dB) 14.9 15.8 20.8 29.6 34.4 31.5 38.5 35.4
H = 34dB, M = 30dB, L=23dB, SNR = 32dB, NRR = 26 dB
Noise Reduction Federal law prohibits removal of LABEL REQUIRED BY U.S EPA REGULATION 40
Rating (NRR) this label before purchase CFR part 211, subpart B
GLOBAL-SYS,
26 dB WH443 XXXX
Bonneuil-sur-Marne, France
Radio
Frequency range : 1870 - 1930 MHz (adjusted according to local regulation)
Transmit power : EU:23 dBm; US/JPN:21dBm
Receive sensitivity : -93 -92 -89 dBm
Modulation : GFSK 1.152 Mbaud
Modulation depth : DECT GFSK bandwidth = 20 dB < 1,728 MHz
Range : Up to 300 meters
Audio Environment
Bandwidth : 150 Hz to 6500Hz at -3 dB Temperature : -20°C to +60°C
IP protection level : IP54
Battery Dimension and weight
Battery type: 650mAh 4.2V LI-Po Dimension : 180x180x100mm
Globalsys Alkaline/NIMH Weight : 565g
Battery life: Up to 6 h with lithium battery
Up to 12h with AA battery 1
Warnings
The noise reduction will be adversely affected by
anything that impairs the seal of the earmuff cushions
against the head, ie. : hair above ears, thick spectacle
frames, balaclavas,... we recommend to remove them to
get the best protection.
The reported attenuation will be obtained only if the protector is in good condition and
worn as directed.
Some chemicals may have a negative effect on this product. It’s recommended to ask
the manufacturer for more information.
The adaptation of hygienic protections on the ear cups can affect the acoustic
performance of the headset.
The output of the audio circuit of this noise protector may exceed the daily limit of the
sound level.
Remember that wearing hearing protectors can reduce noises such as screaming
warning, alarms or other important signals. The user must pay attention to its
surroundings.
Guidelines
Adjustments and maintenance should be done according to manufacturer
instructions.
Headset must be worn permanently in a noisy environment.
The Airlink 3085IA wireless headset can deteriorate with use, it is therefore advised
to inspect them at regular intervals in order to detect any cracks or leaks, for
example .
This headset is equipped with an audio-electric input device. The user should verify
that it works properly before using it. If the user notices a distortion or a defect,
he/she should refer to the manufacturer's instructions.
Product description
The Globalsys Airlink 3085IA wireless headset is designed to protect against harmful
noise and to communicate with an aircraft wirelessly trough an AirLink base station.
This user information is applicable for all versions.
To ensure you get the best comfort, fit and function out of the product, it is
important to read the instructions carefully and save them for future reference.
Please refer to the attenuation table for further details on noise reduction.
Make sure to choose the correct product for your application.
Note :
This headset is only designed for on ground applications and not for use in the aircraft
flightdeck
2
Approvals
The Airlink 3085IA wireless headset meets the Essential Health and Safety
Requirements as laid out in Annex II of the PPEregulation (EU) 2016/425. CE marking
is in accordance with EN352-1:2002 and EN352- 6:2002. This headset is approved and
also monitored acc. to module C2 by PZT (NB1974), GmbH Bismarckstr. 264B, 26389
Wilhelmshaven, Germany.
EU declaration of conformity can be accessed on Globalsys website :
https://global-sys.com/ assets/documents/certifications/eu.pdf
This product conforms to FCC Part 15 standards (CFR 47 FCC PART 15). Compliance
with FCC regulations ensures that this device has been tested and meets the limits
for Class B digital devices.
Storage
When the hearing protector is not in use, store it in such a way that the headband is
not stretched and the cushions are not compressed. Keep the hearing protectors dry
and clean, store them at normal room temperature and do not place them in direct
sunlight.
Maintenance
Clean and disinfect the cups, ear pads and inserts with mild soap and water only.
This product may be adversely affected by certain chemical substances. Further
information should be sought from the manufacturer. Hearing protectors and ear
pads in particular may deteriorate with use and should be examined at frequent
intervals for cracking and leakage, for example at the start of every working shift.
Equipment lifetime depends of environment, type of usage and correct use.
Exposure to extreme weather conditions can impact on headset lifetime, ie.
prolonged exposure to the sun or contaminants in the environment.
Range
Depending upon environment (obstacles…) the range is up to 300 meters (line of
sight).
Materials
Headband : Acetal
Lid : ABS
Spring lid, height adjustment socket, bluetooth button : TPE
Fixation and microphone arm : polyamide
Ear pads and foam : polyuréthane
3
Hygiene kit
TALK
Foam kit (Ref. 33#371)
Left and Right ear pads Microphone Foam x2 internal foam
Ref. 13#37IL & 13#37IR Ref. 03_024 x2 external foam
x2 earpad foam
The cushions and inserts are replaceable. Always replace worn or damaged parts.
Remove the ear pads by pulling it Replace the old internal foam and
straight out. insert with new ones from the
hygiene kit.
Use only hygiene kits from the manufacturer, consisting of one pair of ear pads, one
pair of foam and one microphone foam. A replacement of the hygiene kitis
recommanded for at least twice a year for standard use to ensure that the noise
attenuation performances are maintained. The fitting of hygiene covers to internal
foams may affect the acoustic performance of the hearing protectors. For order
reference, please refer to spare parts list above.
Over the head S M L
earmuffs size 135/122 145/130 150/135
4
Overview
Airlink 3085IA headset
Right side
LED “STATUS”
Volume buttons
ON/OFF button
Charging connector
“MODE” button
Left side
Battery cover
Switch “PTT”
Microphone
5
General fitting instructions
Before following the fitting instructions below, brush excess hair aside and remove any ear
jewellery that could affect acoustic seal. The cushions should form a snug fit against the
head with no interference of the seal by any objects, e.g. respirator headbands or
spectacles arms, and that the cups completely enclose the ears.
1- Make sure to put the headband the right LEFT RIGHT
way round.
The inside of the headband is marked with a letter
L on the left hand side and a letter R on the right
hand side. Ensure that the headband is
positioned correctly.
2- Adjusting the headset
With the headband over the head, adjust the
height of the cups by sliding them up or down, so
they completely enclose the ears.
3- Adjusting the microphone
TALK
Ensure microphone is well orientated.
“TALK” inscription must be turned to mouth side.
System structure
A plug & play base can connect up to 8 wireless headsets or mobiles.
6
Headset functions
ON / OFF Adjust microphone Using microphone
Long press middle Adjust the microphone Upper position : VOX
button to turn ON or to 1 cm from your Middle position : OFF
OFF. mouth. Lower position : PTT
Remove batteries Volume
Replace batteries by opening the You can adjust the audio volume by
black hood with your thumb. Remove pressing "+" or "-" buttons on the
batteries by pulling the tape. headset.
Batteries autonomy Wired charge
Led flash red : headset is charging
Battery ok Low battery Led is Green : headset is charged
A voice prompt will indicate “Low battery” Led off : no charging
frequently if the battery is too low. Charge the battery with an USB-C cable.
LED can be desactivable with a computer (for Night vision mode) 7
Pairing (only first time)
LED signal
Turn on both unit and
wait about 10s. If LEDs
flash, there is no
communication
established.
Pairing activation
Press ON/OFF button
twice on each devices.
LED will start flashing
fast.
Pairing connection
If LED does not flash
both for the base and
the headset :
communication is
established.
Pairing failure Options
If a red light flash for a short time, To select options press lateral button until
connection has failed. If pairing fails : the voice prompt indicates :
1. Check that the headset is not 0.Volume 3.Night vision
already connected. 1.VOX 4.Bluetooth
2. Verify that the headset and base 2.Noise reduction 5. Long range
unit are in a pairing process. Press volume buttons to deactivate or
3. Restart the process. reactivate the selected options
8
Notes
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
For more info
www.Global-sys.com
9
GLOBALSYS
2 bis, avenue des coquelicots, 94380, Bonneuil-Sur-Marne
Phone : +331 43 99 42 17
Mail : [email protected]
Website : www.global-sys.com
