Code Description Explanation and Recommended Procedure
F0 E2 Over suds
F0 E3 Overload
F0 E4 Spin Limited by
Water
Temperature
F0 E5 Off Balance Load
F0 E7 Load Detected
When Running
Clean Washer
Cycle
F0 E8 Water Ring
F0 E9 Off Balance
Pause
F1 E1 Main Control
(ACU) Fault
F2 E1 HMI Stuck Button
F2 E2 HMI
Disconnected
F3 E2 Pressure System
Fault
F5 Lid
E1 Switch
Fault –
Lid id
Open
F5 Lid
E3 Lock
Will
Not
Unlock
F5 E3 means 2 things, cannot unlock or lock. Steps to fix are above or below this line depending on the issue
Lid
Lock
Will
not
Lock
F5 Lid Not Opened
E4 Between Cycles
F6 Communication
E1 Error: HMI
cannot Hear
ACU
F7 Tachometer
E1 missing or
Wrong Signal
F7 Basket Engaged
E3 During Wash
F7 Basked Re-
E4 Engagement
Failure
F7 Motor Circuit
E6 Open
F7 Motor Unable to
E7 Reach Target
RPM
F8 Long Fill
E1
F8 Overflow or Flood
E3 Condition
F8 Water Hazard
E6
F9 Drain Pump
E1 System problem –
Long Drain
Code Diagram
How to read these codes
Reference video: https://www.youtube.com/watch?v=oJ2YfKGWhqM
If LOCK light is lit up (the LED), this means that anything that is lit up within the set of LEDs titled
[Sense – Soak – Wash – Done] is an F code
Example of an F code. This is an F code because the Lid Lock LED is lit along the other codes mentioned before
If LOCK light is NOT lit up (the LED), this means that anything that is lit up within the set of LEDs
titled [Sense – Soak – Wash – Done] is an E code
Example of an E code. This is an E code because the Lid Lock LED is lit along the other codes mentioned before
Using this key diagram, we can give the codes number values
Reading the LED lights, if they are on, that means the value of that
light is 1. If it is off, then it is 0. So reading this example here, the code is
Sense – Soak – Wash – Done
0 - 1 - 0 - 0
so the code is 0100.
This code here is an F code of 0 – 1 – 1 – 1 This code here is an E code of 0 – 1 – 0 – 0
Looking at the diagram or putting this into a Using the calculator from the left side, we know this
calculator, we get 7. So F7 is the code. Is a 4. So the code is E4.
One Last Thing
Found this on the internet, might be useful for entering service mode
Bottom row of buttons from left to right are key 1 2 3 and 4. The key above 4 is 5 and above that is 6.
TO ENTER SERVICE MODE
1. Be sure the washer is in standby mode (plugged in with all LEDs off).
2. Follow the steps below within 8 seconds: • Press and Release the Key 1 • Press and Release the
Key 2 • Press and Release the Key 3 • Repeat this 3 button sequence 2 more times.
3. If there is no recent error occurred. Upon entering service mode successfully, all LEDs will flash
twice, in case of no previous error stored and then turn OFF.
4. If there is a recent error code saved in the system, all LEDs will flash once and then error code
will be automatically shown before entering any other service mode sub-menu. If no error
codes are saved, then progress bar LED (Sense, Soak, Wash, Done) will blink twice.
UI test Press Key 1, Auto Test Press Key 2 then 5. Auto test does Water valve on/off, Drain Pump on/off,
shifter/motor agitation test, lid lock/spin test in that order. During a test key 2 goes to the next test key 1 to
previous test.
