LCDWIKI 3.

5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

3.5inch 8&16BIT Module MRB3511

User Manual

www.lcdwiki.com 1 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

Product Description

The product is a 3.5-inch TFT LCD display module with capacitive touch screen. It

has 480x320 resolution, supports 16BIT RGB 65K color display, and the internal driver IC

is ILI9488, which uses 8-bit or 16-bit parallel port communication. The module includes

LCD display, capacitive touch screen and PCB backplane. It can be plugged into the TFT

LCD slot of the STM32 series development board or used on the C51 platform.

Product Features

 3.5-inch color screen, support 16BIT RGB 65K color display, display rich colors

 320x480 resolution for clear display

 Support 8-bit or 16-bit parallel data bus mode switching, fast transfer speed

 Supports ALIENTEK STM32 Mini, Elite, WarShip, Explorer, and Apollo development

boards direct plug-in use

 Support for capacitive touch function

 Provides a rich sample program for STM32 and C51 platforms

 Military-grade process standards, long-term stable work

 Provide underlying driver technical support

Product Parameters

Name Description

Display Color 16BIT RGB 65K color

SKU MRB3511

Screen Size 3.5(inch)

Screen Type TFT

Driver IC ILI9488

Resolution 480*320 (Pixel)

Module Interface 8Bit or 16Bit parallel interface

www.lcdwiki.com 2 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

Active Area 48.96x73.44 (mm)

Touch Screen Type Capacitive touch screen

Touch IC GT911

Module PCB Size 56.41x97.60 (mm)

Operating Temperature -10℃~60℃

Storage Temperature -20℃~70℃

Operating Voltage 3.3V / 5V

Power Consumption TBD

Product Weight(Including packaging) 57g

Interface Description

Picture1. Module rear view

www.lcdwiki.com 3 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

Picture2. Module Pin silk screen picture

NOTE:
1. The module hardware supports 8-bit and 16-bit parallel port data bus mode

switching (shown in red box in Picture 1), as follows:

A. Solder R16 with 0Ω resistor or short circuit directly, and disconnect R8:

Select 16-bit parallel port data bus mode, use DB0~DB15 data pins(default)

B. Solder R8 with 0Ω resistor or short circuit directly, and disconnect R16:

Select 8-bit parallel port data bus mode, use DB0~DB7 data pins

Important Note:
1. The following pin numbers 1~34 are the pin number of Module pin with PCB

backplane of our company. If you purchase a bare screen, please refer to the

pin definition of the bare screen specification, refer to the wiring according to

the signal type instead of directly Wire according to the following module pin

numbers. For example: CS is 1 pin on our module. It may be x pin on different

size bare screen.

2. About VCC supply voltage: If you buy a module with PCB backplane, VCC/VDD

power supply can be connected to 5V or 3.3V (module has integrated ultra low

dropout 5V to 3V circuit), but it is recommended to connect 3.3V, because

www.lcdwiki.com 4 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

connecting 5V will lead to circuit Increased heat generation, affecting module

life; if you buy a bare screen LCD, remember to only connect 3.3V.

3. About the backlight voltage: The module with the PCB backplane has

integrated triode backlight control circuit, which only needs to input the high

level of the BL pin or the PWM wave to illuminate the backlight. If you are

buying a bare screen, the LEDAx is connected to 3.0V-3.3V and the LEDKx is

grounded.

Number Module Pin Pin Description

1 CS LCD reset control pin( low level enable)

LCD register / data selection control pin
2 RS
(high level: register, low level: data)
3 WR LCD write control pin
4 RD LCD read control pin
5 RST LCD reset control pin( low level reset)

6 DB0
7 DB1
8 DB2
9 DB3
LCD data bus low 8-bit pin
10 DB4
11 DB5
12 DB6
13 DB7
14 DB8
15 DB9
16 DB10

17 DB11 LCD data bus high 8-bit pin(When using the 8-bit
parallel port data bus mode, the upper 8-bit pin is
18 DB12
not used.)
19 DB13

20 DB14
21 DB15

www.lcdwiki.com 5 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

22 GND Module power ground pin

23 BL LCD backlight control pin(High level light)

24 VDD Module power positive pin (module has

integrated voltage regulator IC, so the power
25 VDD supply can be connected to 5V or 3.3V)

26 GND
Module power ground pin
27 GND

LCD backlight power positive pin (default shared

28 NC onboard backlight power supply, this pin can not be
connected)
29 NC Not defined, no need to use
30 SDA Capacitive touch screen IIC bus data pin
Capacitive touch screen interrupt detection pin
31 INT
(low level when a touch occurs)
32 NC Not defined, no need to use
Capacitive touch screen IC reset control pin (low
33 CRST
level reset)
34 SCL Capacitive touch screen IIC bus clock pin

Hardware Configuration

The LCD module hardware circuit comprises five parts: an LCD display control circuit, a

power control circuit, a data bus mode selection control circuit, a touch screen control

circuit and a backlight control circuit.

LCD display control circuit for controlling the pins of the LCD, including control pins and

data transfer pins.

Power control circuit for stabilizing the supply voltage and selecting the external supply

voltage

Data bus mode selection control circuit for selecting 8-bit or 16-bit data bus mode.

Capacitive touch screen control circuit is used to control touch screen interrupt acquisition,

data sampling, AD conversion, data transmission, etc.

A backlight control circuit is used to control the brightness of the backlight.

www.lcdwiki.com 6 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

working principle

1. Introduction to ITI9488 Controller

The ITI488 controller supports a maximum resolution of 320*480 and has a

345600-byte GRAM. It also supports 8-bit, 9-bit, 16-bit, 18-bit and 24-bit parallel port data

buses. It also supports 3-wire and 4-wire SPI serial ports. Since the supported resolution

is relatively large and the amount of data transmitted is large, the parallel port

transmission is adopted, and the transmission speed is fast. ITI9488 also supports 65K,

262K and 16.7M RGB color display, display color is very rich, while supporting rotating

display and scroll display and video playback, display in a variety of ways.

The ITI9488 controller uses 16bit (RGB565) to control a pixel display, so it can

display up to 65K colors per pixel. The pixel address setting is performed in the order of

rows and columns, and the incrementing and decreasing direction is determined by the

scanning mode. The ITI9488 display method is performed by setting the address and then

setting the color value.

2. Introduction to parallel port communication

The parallel port communication write mode timing is as shown below:

www.lcdwiki.com 7 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

The timing of the parallel port communication read mode is shown in the figure below:

CSX is a chip select signal for enabling and disabling parallel port communication,

active low

RESX is an external reset signal, active low

D/CX is the data or command selection signal, 1-write data or command parameters,

0-write command

WRX is a write data control signal

RDX is a read data control signal

D[X:0] is a parallel port data bit, which has four types: 8-bit, 9-bit, 16-bit, and 18-bit.

When performing a write operation, on the basis of the reset, first set the data or

command selection signal, then pull the chip select signal low, then input the content

to be written from the host, and then pull the write data control signal low. When

pulled high, data is written to the LCD control IC on the rising edge of the write control

signal. Finally, the chip select signal is pulled high and a data write operation is

completed.

www.lcdwiki.com 8 / 26 Rev1.0
 LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

When entering the read operation, on the basis of the reset, first pull the chip

select signal low, then pull the data or command select signal high, then pull the read

data control signal low, and then read the data from the LCD control IC. And then The

read data control signal is pulled high, and the data is read out on the rising edge of

the read data control signal. Finally, the chip select signal is pulled high, and a data

read operation is completed.

Instructions for use

1. STM32 instructions
Wiring instructions:

See the interface description for pin assignments.

Note:
1. This module can be directly inserted into the TFTLCD slot of the

punctual atom development board, no manual wiring is required.

2. The following internal plug-in pins of the corresponding MCU refer to the

MCU pins directly connected to the TFTLCD slot inside the development

board, only for reference.

MiniSTM32 development board TFTLCD socket in-line instructions

Corresponding Corresponding to STM32F103RCT6
Number Module Pin
TFTLCD socket pin microcontroller internal connection pin
1 CS CS PC9
2 RS RS PC8
3 WR WR PC7
4 RD RD PC6
5 RST RST PC4
6 DB0 D0 PB0
7 DB1 D1 PB1
8 DB2 D2 PB2
9 DB3 D3 PB3
10 DB4 D4 PB4

www.lcdwiki.com 9 / 26 Rev1.0
 LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

11 DB5 D5 PB5
12 DB6 D6 PB6
13 DB7 D7 PB7
14 DB8 D8 PB8
15 DB9 D9 PB9
16 DB10 D10 PB10
17 DB11 D11 PB11
18 DB12 D12 PB12
19 DB13 D13 PB13
20 DB14 D14 PB14
21 DB15 D15 PB15
22 GND GND GND
23 BL BL PC10
24 VDD 3.3 3.3V
25 VDD 3.3 3.3V
26 GND GND GND
27 GND GND GND
28 NC Not used 5V
29 NC Not used PC2
30 SDA MOSI PC3
31 INT PEN PC1
32 NC Not used NC
33 CRST TCS PC13
34 SCL CLK PC0

Elite STM32 development board TFTLCD socket in-line instructions

Corresponding Corresponding to STM32F103ZET6
Number Module Pin
TFTLCD socket pin microcontroller internal connection pin

1 CS CS PG12
2 RS RS PG0
3 WR WR PD5

www.lcdwiki.com 10 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

4 RD RD PD4
5 RST RST reset pin
6 DB0 D0 PD14
7 DB1 D1 PD15
8 DB2 D2 PD0
9 DB3 D3 PD1
10 DB4 D4 PE7
11 DB5 D5 PE8
12 DB6 D6 PE9
13 DB7 D7 PE10
14 DB8 D8 PE11
15 DB9 D9 PE12
16 DB10 D10 PE13
17 DB11 D11 PE14
18 DB12 D12 PE15
19 DB13 D13 PD8
20 DB14 D14 PD9
21 DB15 D15 PD10
22 GND GND GND
23 BL BL PB0
24 VDD VDD 3.3V
25 VDD VDD 3.3V
26 GND GND GND
27 GND GND GND
28 NC Not used 5V
29 NC Not used PB2
30 SDA MOSI PF9
31 INT PEN PF10
32 NC Not used NC
33 CRST TCS PF11
34 SCL CLK PB1

www.lcdwiki.com 11 / 26 Rev1.0
 LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

WarShip STM32 development board TFTLCD socket in-line

instructions
Corresponding to STM32F103ZET6
Corresponding
Number Module Pin microcontroller internal connection pin
TFTLCD socket pin
V2 V3

1 CS CS PG12
2 RS RS PG0
3 WR WR PD5
4 RD RD PD4
5 RST RST reset pin
6 DB0 D0 PD14
7 DB1 D1 PD15
8 DB2 D2 PD0
9 DB3 D3 PD1
10 DB4 D4 PE7
11 DB5 D5 PE8
12 DB6 D6 PE9
13 DB7 D7 PE10
14 DB8 D8 PE11
15 DB9 D9 PE12
16 DB10 D10 PE13
17 DB11 D11 PE14
18 DB12 D12 PE15
19 DB13 D13 PD8
20 DB14 D14 PD9
21 DB15 D15 PD10
22 GND GND GND
23 BL BL PB0
24 VDD VDD 3.3V
25 VDD VDD 3.3V
26 GND GND GND
27 GND GND GND
28 NC Not used 5V

www.lcdwiki.com 12 / 26 Rev1.0
 LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

29 NC Not used PF8 PB2

30 SDA MOSI PF9
31 INT PEN PF10
32 NC Not used NC
33 CRST TCS PB2 PF11
34 SCL CLK PB1

Explorer STM32F4 development board TFTLCD socket in-line

instructions
Corresponding Corresponding to STM32F407ZGT6
Number Module Pin
TFTLCD socket pin microcontroller internal connection pin
1 CS CS PG12
2 RS RS PF12
3 WR WR PD5
4 RD RD PD4
5 RST RST reset pin
6 DB0 D0 PD14
7 DB1 D1 PD15
8 DB2 D2 PD0
9 DB3 D3 PD1
10 DB4 D4 PE7
11 DB5 D5 PE8
12 DB6 D6 PE9
13 DB7 D7 PE10
14 DB8 D8 PE11
15 DB9 D9 PE12
16 DB10 D10 PE13
17 DB11 D11 PE14
18 DB12 D12 PE15
19 DB13 D13 PD8
20 DB14 D14 PD9
21 DB15 D15 PD10

www.lcdwiki.com 13 / 26 Rev1.0
 LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

22 GND GND GND

23 BL BL PB15
24 VDD VDD 3.3V
25 VDD VDD 3.3V
26 GND GND GND
27 GND GND GND

28 NC Not used 5V

29 NC Not used PB2

30 SDA MOSI PF11
31 INT PEN PB1
32 NC Not used NC
33 CRST TCS PC13
34 SCL CLK PB0

Apollo STM32F4/F7 development board TFTLCD socket in-line

instructions
Corresponding to STM32F429IGT6、
Corresponding
Number Module Pin STM32F767IGT6、STM32H743IIT6
TFTLCD socket pin
microcontroller internal connection pin
1 CS CS PD7

2 RS RS PD13
3 WR WR PD5
4 RD RD PD4
5 RST RST reset pin

6 DB0 D0 PD14
7 DB1 D1 PD15
8 DB2 D2 PD0
9 DB3 D3 PD1
10 DB4 D4 PE7
11 DB5 D5 PE8
12 DB6 D6 PE9
13 DB7 D7 PE10

www.lcdwiki.com 14 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

14 DB8 D8 PE11
15 DB9 D9 PE12
16 DB10 D10 PE13
17 DB11 D11 PE14
18 DB12 D12 PE15
19 DB13 D13 PD8
20 DB14 D14 PD9
21 DB15 D15 PD10
22 GND GND GND
23 BL BL PB5
24 VDD VDD 3.3V
25 VDD VDD 3.3V
26 GND GND GND
27 GND GND GND
28 NC Not used 5V
29 NC Not used PG3

30 SDA MOSI PI3

31 INT PEN PH7

32 NC Not used NC
33 CRST TCS PI8
34 SCL CLK PH6

Operating Steps：

A. Connect the LCD module(As shown in Picture 1) and the STM32 MCU according

to the above wiring instructions, and power on;

B. Select the C51 test program to be tested, as shown below:

(Please refer to the test program documentation for the test program description.

If you need to use patch, please refer to the patch documentation in the

STM32_Demo_patch directory.)

www.lcdwiki.com 15 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

C. Open the selected test program project, compile and download;

detailed description of the STM32 test program compilation and download can be

found in the following document:

http://www.lcdwiki.com/res/PublicFile/STM32_Keil_Use_Illustration_EN.pdf

D. If the LCD module displays characters and graphics normally, the program runs

successfully；

2. C51 instructions
Wiring instructions:

See the interface description for pin assignments.

Note:
1. Since the input and output levels of the GPIO of the STC12C5A60S2

www.lcdwiki.com 16 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

microcontroller are 5V, the capacitive touch IC cannot work normally (only

1.8~3.3V can be accepted). If you want to use the capacitive touch

function, you need to connect to the level conversion module;

2. Since the STC89C52RC microcontroller does not have a push-pull output

function, the backlight control pin needs to be connected to a 3.3V power

supply to be properly lit.

3. Since the STC89C52RC microcontroller's Flash capacity is too small (less

than 25KB), the program with touch function cannot be downloaded, so

the touch screen does not need wiring.

STC12C5A60S2 microcontroller test program wiring instructions

Corresponding to STC12 development board
Number Module Pin
wiring pin
1 CS P13

2 RS P12
3 WR P11
4 RD P10
5 RST P33
6 DB0 P00
7 DB1 P01
8 DB2 P02
9 DB3 P03
10 DB4 P04
11 DB5 P05
12 DB6 P06
13 DB7 P07
14 DB8 P20
15 DB9 P21
16 DB10 P22
17 DB11 P23
18 DB12 P24

www.lcdwiki.com 17 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

19 DB13 P25
20 DB14 P26
21 DB15 P27
22 GND GND
23 BL P32
24 VDD 3.3V/5V
25 VDD 3.3V/5V
26 GND GND
27 GND GND
28 NC No need to connect
29 NC No need to connect
30 SDA P34
31 INT P40
32 NC No need to connect
33 CRST P37
34 SCL P36

STC89C52RC microcontroller test program wiring instructions

Corresponding to STC89 development board
Number Module Pin
wiring pin
1 CS P13
2 RS P12
3 WR P11
4 RD P10
5 RST P14
6 DB0 P30
7 DB1 P31
8 DB2 P32
9 DB3 P33
10 DB4 P34
11 DB5 P35
12 DB6 P36

www.lcdwiki.com 18 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

13 DB7 P37
14 DB8 P20
15 DB9 P21
16 DB10 P22
17 DB11 P23
18 DB12 P24
19 DB13 P25
20 DB14 P26
21 DB15 P27
22 GND GND
23 BL 3.3V
24 VDD 3.3V/5V
25 VDD 3.3V/5V
26 GND GND
27 GND GND
28 NC No need to connect
29 NC No need to connect
30 SDA No need to connect
31 INT No need to connect
32 NC No need to connect
33 CRST No need to connect
34 SCL No need to connect

Operating Steps：

A. Connect the LCD module (As shown in Picture 1)and the C51 MCU according to

the above wiring instructions, and power on;

B. Select the C51 test program to be tested, as shown below:

(Test program description please refer to the test program description document

in the test package)

www.lcdwiki.com 19 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

C. Open the selected test program project, compile and download;

detailed description of the C51 test program compilation and download can be

found in the following document:

http://www.lcdwiki.com/res/PublicFile/C51_Keil%26stc-isp_Use_Illustration_EN.pdf

D. If the LCD module displays characters and graphics normally, the program runs

successfully；

Software Description

1. Code Architecture
A. C51 and STM32 code architecture description

The code architecture is shown below:

Sample code

Test code GUI code LCD code main Platform code

IIC code GT911 touch Key code Led code

control code

The Demo API code for the main program runtime is included in the test code;

LCD initialization and related bin parallel port write data operations are included in the

LCD code;

Drawing points, lines, graphics, and Chinese and English character display related

operations are included in the GUI code;

The main function implements the application to run;

www.lcdwiki.com 20 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

Platform code varies by platform;

The IIC code is used by the capacitive touch IC GT911, including IIC initialization,

data writing and reading, etc;

GT911 touch control code includes touch detection, touch command transmission

and touch data reading, etc.

The key processing related code is included in the key code (the C51 platform does

not have a button processing code);

The code related to the led configuration operation is included in the led code(the

C51 platform does not have a led processing code);

2. GPIO definition description

A. STM32 test program GPIO definition description

The GPIO definition of the LCD screen of the STM32 test program is placed in the

lcd.h file, which is defined in two ways:

1) STM32F103RCT6 microcontroller test program uses IO analog mode (it does

not support FSMC bus)

2) Other STM32 MCU test programs use FSMC bus mode

STM32F103RCT6 MCU IO analog test program LCD screen GPIO definition as

shown below:

FSMC test program lcd screen GPIO is defined as shown below (take

STM32F103ZET6 microcontroller FSMC test program as an example):

www.lcdwiki.com 21 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

The STM32 touch screen related GPIO definition consists of two parts: IIC's GPIO

definition and screen interrupt and reset GPIO definition.

The IIC GPIO definition is placed in the gtiic.h file as shown below (take the

STM32F103ZET6 microcontroller FSMC test program as an example):

The interrupt of the screen and the reset GPIO definition are placed in GT911.h, as

shown in the following figure (take the STM32F103ZET6 microcontroller FSMC test

program as an example):

www.lcdwiki.com 22 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

B. C51 test program GPIO definition description

C51 test program lcd screen GPIO definition is placed in the lcd.h file, as shown

below(Taking the STC12C5A60S2 microcontroller test program as an example):

Parallel pin definition needs to select the whole set of GPIO port groups, such as P0,

P2, etc., so that when transferring data, the operation is convenient.Other pins can be

defined as any free GPIO.

The C51 touch screen related GPIO definition consists of two parts: IIC's GPIO

definition and screen interrupt and reset GPIO definition.

The IIC GPIO definition is placed in the gtiic.h file as shown below (take the

STC12C5A60S2 microcontroller test program as an example):

The interrupt of the screen and the reset GPIO definition are placed in GT911.h, as

shown in the following figure (take the STC12C5A60S2 microcontroller test program

as an example):

www.lcdwiki.com 23 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

The GPIO definition of the touch screen can be modified and can be defined as any

other free GPIO.

If the microcontroller does not have a P4 GPIO group, penirq can be defined as other

GPIOs.

3. Parallel port communication code implementation

A. STM32 test program parallel port communication code implementation

The STM32 test program parallel port communication code is placed in the LCD.c file,

which is implemented in two ways:

1) STM32F103RCT6 microcontroller test program uses IO analog mode (it does

not support FSMC bus)

2) Other STM32 MCU test programs use FSMC bus mode

The IO simulation test program is implemented as shown below:

The FSMC test program is implemented as shown below:

www.lcdwiki.com 24 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

Both 8- and 16-bit command writes and 8- and 16-bit data writes and reads are

implemented.

B. C51 test program parallel port communication code implementation

The relevant code is implemented in the LCD.c file as shown below:

Implemented 8-bit and 16-bit commands and 8-bit and 16-bit data write and read.

www.lcdwiki.com 25 / 26 Rev1.0
LCDWIKI 3.5inch 8&16BIT Module MRB3511 User Manual CR2019-MI4701

Common software

This set of test examples requires the display of Chinese and English, symbols and

pictures, so the modulo software is used. There are two types of modulo software:

Image2Lcd and PCtoLCD2002. Here is only the setting of the modulo software for the test

program.

The PCtoLCD2002 modulo software settings are as follows:

Dot matrix format select Dark code

the modulo mode select the progressive mode

Take the model to choose the direction (high position first)

Output number system selects hexadecimal number

Custom format selection C51 format

The specific setting method is as follows:

http://www.lcdwiki.com/Chinese_and_English_display_modulo_settings

Image2Lcd modulo software settings are shown below:

The Image2Lcd software needs to be set to horizontal, left to right, top to bottom,

and low position to the front scan mode.

www.lcdwiki.com 26 / 26 Rev1.0