High Quality

Starter and Alarm Systems

We sincerely appreciate you purchasing our
vehicle starter and alarm systems. Our starter and
alarm systems are produced with strict quality control
and international standards, and includes a series of
test including; extreme temperature, shocks, vibration
and dropping. As a result, we are certain that you will
be completely satisfied with our products.

Please read this manual carefully prior to using your new

system. Please keep this manual accessible for future use.
 [Remote Outside Name]

Window
RESET
LCD Displays

Button I
Button II Charger
Button III Connector

Hook

▶ LF Module ▶Start Button (E6-B only)

▶Antenna Module

[Accessories]

▶Cigar Jack Connetor ▶Computer USB Connector

 Safety Information
※Please take these safety precautions.
1. Please read our Limited Warranty and Disclaimer
information located at the back of this manual prior to
using.
2. It is not recommended installing this systen into a
convertible vehicle with a manual transmission.
3. We are not responsible for any injury or other liability
resulting from the wrongful use of this system
4. When using remote start, place the gear in the Parked
or Neutral position, and set the Emergency brake or
Foot brake
5. In manual transmission vehicles; Do Not remote start
in any position other than Neutral. We are not
responsible for any damages or consequence
resulting from this.
6.The transmitting (TX) and receiving (RX) varies
depends on the radio signal environment. Range and
response time will vary.
7. In the unlikely event of a defective product, do not
open, repair or modify the system. Ask the seller for
repair or replacement.
8. We shall not be responsible for any theft or damage to
your vehicle, since this is a subsidiary and convenient
system only.
9. Please note that some functions described in this
manual are optional functions and may not be
available on this model.
CONTENTS

Greeting
Remote Outside Name
Safety Information
LCD Displays……………………………………………………… 6
Remote Button Functions………………………………………… 8

[Ⅰ]
1. Lock/Unlock (Arm/Disarm)………………………………… 9
1-1 Door Lock (Arm)……………………………………………… 9
1-2 Door Unlock (Disarm)………………………………………… 10
2. Auxiliary Output (Optional Installation)…………………… 10
2-1 Aux1…………………………………………………………… 10
2-2 Aux2…………………………………………………………… 10
3. Query Function …………………………………………… 11
4. Valet………………………………………………………… 11
5. Vibration (On/Off) ………………………………………… 12
6. Panic Mode………………………………………………… 12
7. Remote Start……………………………………………… 13
7-3 Emergency Brake(Option setting) ………………………… 13
7-4 Preventing Remote Start for your safety …………………… 14
7-5 Diagnose problems with auto start………………………… 14
8. Start Button (E6-B Only)………………………………………… 15
8-1 Ignition ON…………………………………………………… 15
8-2 Ignition OFF…………………………………………………… 15
8-3 OFF → ACC → ON → OFF………………………………… 16
9. Power (On/Off)……………………………………………… 16
10. Trunk Open……………………………………………… 16
10-1 Trunk Open………………………………………………… 16
10-2 Trunk sensing (option setting)……………………………… 17

[Ⅱ]
1. Easy fuction ON/OF……………………………………… 17
2. Passive……………………………………………………… 18
 2-1 Auto Arming…………………………………………………… 18
2-2 Manual Arming……………………………………………… 19
3. Driving Door Lock (Ignition Lock)………………………… 19
4. Mute………………………………………………………… 20
5. Reservation start (On/Off) ………………………………… 20
6. Turbo………………………………………………………… 20
6-2 Start button model …………………………………………… 21
7. Shock sensor by-pass …………………………………… 22
8. Smart Door………………………………………………… 22
9. Current Time Change……………………………………… 23
10. Reserved Time Change ………………………………… 24

[EASY Option Setup ]………………………………………… 24

[ Others ]
1.Real Time Remote Paging Functions…………………… 25
1-1 Owner Call Mode…………………………………………… 26
1-2 Shock Sensing Report Mode ……………………………… 26
1-3 Theft Report Mode …………………………………………… 26
2. Adjusting the sensitivity of shock sensor ………………… 26
3. Reservation Mode(For Manual Transmission Vehicle)…… 27
3-1 What is 'Reservation mode'?………………………………… 27
3-2 Automatic Reservation Mode(Default Setting)……………… 28
3-3 Manual Reservation Mode (Option setting)………………… 28
4. Easy Door Lock(Option)…………………………………… 28
4-2 How to input the 4 digit password…………………………… 29
4-3 Door Lock/Unlock…………………………………………… 29
4-4 LED Display…………………………………………………… 30
5. Parking Timer / Car temperature check / Car Voltage chek …… 31
6. Charging time alert ………………………………………… 31
7. Reset……………………………………………………… 31
[LCD displays]

CAUTION
Use of this system is for car start and alarm purpose only.
Since this system is a precise instrument that is fragile and
susceptible to damage from external shock, do not drop the unit, and
keep it away from children. Do not keep the remote near excessive
humidity or water, as it is not water proof.

LCD Icon LCD Function

Transmitted

Transmitting

Reservation mode
(Manual transmission only)

Door Lock (Arm)

Door Unlock (Disarm)

6 / USER'S GUIDE
LCD Icon LCD Function

Panic Mode

Vibration On/Off

Trunk open

Door open

Shock

Timer

Remote Start

Valet

Passive

Turbo

Clock

Driving door lock(Ignition Lock)

Battery Meter

Smart Door

7
8 / USER'S GUIDE
* 0.5 sec. : Press the button for 0.5 second.
* 2 seconds(-) : Press the button for 2 seconds till it operates at
your vehicle
* + : Press 2 buttons simultaneously.

[Ⅰ]
1. Lock/Unlock (Arm/Disarm)

1-1 Door Lock (Arm)

You can lock and arm your
vehicle by pressing button
for 0.5 second. The siren chirps
and the parking lights flash
once each, Also, the sidemirror
is being folded.(Optional
installation)

: Once

(E6-B Only)

Note
The remote chirps 7 times, and blinks icon on the remote
to warn that the battery of your vehicle discharges, if you lock

9
 the doors while the tail lights are turned on during arming.
1-2 Door Unlock (Disarm)
You can open and disarm your
vehicle by pressing button
for 0.5 second.
The siren chirps and the parking
light flash twice each.
Also, the sidemirror is being
unfolded (Optional installation).
The numbers of remote chirps
: Twice and parking light flashes indicate
the status of your vehicle while
parking (Alarm models only).
- Two chirps and two parking light flashes indicates there
were no problems while parking.
- Four chirps and four parking light flashes on the remote
indicates there has been an alarm during the arming stage.

2. Auxiliary Output (Optional Installation)

This mode is used to control (on/off) one of the various
functions on your vehicle (such as convertible, sunroof, car
audio, window and etc.)

2-1 Aux1
It operates by pressing for 0.5 second and then do it
again within 3 seconds to open sunroof etc. To close, please
do the same process once again.

2-2 Aux2

10/ USER'S GUIDE

 It operates by pressing for 0.5 second and then do it
again within 3 seconds to open sunroof etc. To close, please
do the same process once again.

3. Query Function
Query function allows you to check the statues of your
vehicle including car battery voltage, car temperature and
parking timer (it indicates how many minutes and hours
have passed after the system is armed). By pressing button
IV for 0.5 second, it shows the parking timer and then either
car temperatureorcarbattery voltage (theother one appears
as the same button job is repeated).
The icon and chirping sounds indicates the statues. If you
are within transmitting distance to receive the signal for
shock, theft and easy call function, you will receive the
response shown on the table.
Response
Status Remote Siren from
the vehicle
Engine Running, Armed Be, bip Be×4 Chirp×3
Enging is Not Running, Armed Bip Be×4 Chirp
Enging is running, Disarmed Be, bip×2 Be×4 Chirp×4
Engine is not running, Disarmed Bip×2 Be×4 Chirp×2

4. Valet

11
 Press button ( + )
simultaneously for 0.5 second to
enter this mode.
The 2 features operating in valet
mode are Door lock / unlock by
pressing button and Query
function by pressing button (
+ ). (All the other
functions do not operate temporarily.)
Valet mode is useful when loaning your vehicle or having it
serviced (example, car wash, parking lot and auto repair
shop).
Press button ( + ) simultaneously for 0.5 second again
to exit.

Note
If you want to use this mode manually, insert the key into the
ignition and rotate it(press the start button in E6-B model) 4
times between ON & OFF for 4 times within 10 seconds.

5. Vibration (On/Off)
Press button ( + ) for 0.5 second(Vibration on), and
press button ( + ) for 0.5 second again to turn it off.

6. Panic Mode
Press and hold button for 2 seconds to activate this mode.
Your vehicle will lock the doors if unlocked, the siren will

12/ USER'S GUIDE

 activate, and the parking lights will flash for 90 seconds. This
function is used for warning under emergency situations,
when you feel you are in danger.
Press and hold button for 2 seconds to deactivate.

7. Remote Start
7-1
 ress and hold button
P , for 2
seconds, the remote chirps and
the parking lights flash once
each.
If it fails, the system
automatically repeats remote
start a maximum of 3 times.
When the vehicle starts,
: Once appears on the transmitter and
the remaining engine running
time is displayed on the remote.
The default setting of the engine running time is 15
minutes. You can change it to 25 minutes by using optional
settings.

7-2
Open the door, insert the key, and turn it to ON position
after remote start, If you want to stop the auto starting,
press the foot brake.

7-3 Emergency Brake(Option setting)

13
 Manual transmission vehicles need Reservation mode to
remote start, in this case, the emergency brake must be ON.

7-4 Preventing Remote Start for your safety

The following cases prevent your vehicle from auto
starting for your safety.
① If trunk is open
② If hood is open (Exept for E6-B)
③ If emergency brake is off (for manual transmission
vehicles only)
④ If panic mode is activated
⑤ If valet mode is activated (Refer to ‘Valet’)

7-5 Diagnose problems with auto start

If there is a problem in auto start, you will hear 3 chirps
and the cause for the error will be indicated by the number
of chirps and the parking lights flash within 3 seconds,
when you try the remote start (Refer to the table).
Vehicle Remote
Number of Reason
chirps or Park Cause of error of fail
light Flash
1 Engine on Start
2 Key On Start
3 Door open Door
4 Trunk open Trunk
5 Foot brake on Foot brake
6 Hood open (Exept for E6-B) Hood
Reservation Off
7 Reservation
(Manual transmission)

14/ USER'S GUIDE

8. Start Button (E6-B Only)
Push button Ignition ON/OFF

8-1 Ignition ON
While pressing the foot brake on,
press start button for 1 secound.
Also, the parking brake (Auto
transmission) or the emergency
brake (manual transmission) should
be on at this stage. You will see the
engine get started and on the button,
it has the red colored light on (Stop).
Once you release the parking brake (Auto transmission) or
emergency brake (manual transmission) to drive, the red
colored light is off.

8-2 Ignition OFF

① While pressing the foot brake on,
press start button for 1 secound.
Also, the parking brake (Auto
transmission) or the emergency
brake (manual transmission)
should be on at this stage. you will
see the engine is off and the button
gets the light on (Start).
② In case you are not able to stop the engine due to the
problem from the parking brake (Auto transmision) or
the emergency brake (manual transmission), press start
button for 4 seconds while pressing the foot brake on.
Then the engine will stop.

15
 Note
When the parking brake (Auto transmission) or the emergency
brake (Manual transmission) is broken, check whethen the red
colored light is on (Stop). And then press the start button for about
4 seconds (while foot brake on) to start, until you confirm the
engine is running.
If you want to stop the engine while you are outside of your vehicle,
1) check the red colored light is on ‘stop’, 2) open the door and
press the button II for 2 seconds.

8-3 OFF → ACC → ON → OFF

① ACC : While not pressing the foot brake on, press the start
button on time, the button gets the light on ACC, which
enables you use the air-conditioning and car audio etc.
② ON : If you press one more while not pressing the foot
brake on, the button gets the light on OFF.
③ To stop the engine by force : If you are not able to stop the
engine by pressing button, please open and close the car
door 7times during 12 seconds. Then the engine will stop.

9. Power (On/Off)
When remote is not in use for a long time, press button
for 5 seconds to turn it off. To turn back on, press button
for 5 seconds once again.

10. Trunk Open

10-1 Trunk Open

16/ USER'S GUIDE

 Press and hold button for 2
seconds to open the trunk.
Parking lights will flash twice
and the siren will chirp twice.

: Twice

10-2 Trunk sensing (option setting)

While your trunk is open, you cannot lock the doors (or
arm the vehicle.

[Ⅱ]
1. Easy fuction ON/OFF
You can make function ON/OFF easily by looking at icons
on display.
Press the button ( + ) for 2 seconds, then each function
icon takes turns appearing, along with Arabic number that
indicates which button to be pressed and how long.
(For example, 1 = for 0.5 sec, 1- = for 2 sec , 12 = (
+ ) for 0.5sec. 12- = ( + ) for 2sec). If you press
designated button while certain icon (function) is pressed
as indicated in the list, the function change is set up.

17
 ① for 0.5 seconds Passive

② for 0.5 seconds Mute

③ for 0.5 seconds Turbo

④ for 2 seconds Ignition Lock

Reservation
⑤ for 2 seconds Start
⑥ for 2 seconds Shock sensor

⑦ ( + ) Smart door
for 0.5 seconds

⑧ ( + ) Current Time
for 2 seconds

⑨ ( + ) Reserve Time
for 2 seconds

2. Passive
2-1 Auto Arming
① You c an ac t ivate t his
function by pressing button
( + ) simultaneously
for 2 seconds and then press
button for 0.5 second.
Then, Icon appears on the
LCD and this system rearms
automatically.
 he doors lock and rearm 30 seconds after the engines is
②T
turned off and the doors are closed.

18/ USER'S GUIDE

  uring auto start mode, The doors lock and rearm 30
③D
seconds after the doors are closed.
During Valet mode, auto arming mode is not activated.

2-2 Manual Arming

The Icon disappears on LCD and doors are locked and
unlocked by remote only, if you press button ( + )
simultaneously for 2 seconds and then press button
for 0.5 second.
The doors automatically lock and arm, if you don't open
the doors more than 1 minute after you disarm by remote.

3. Driving Door Lock (Ignition Lock)

Press button ( + )
simultaneously for 2 seconds
and then press button for
0.5 second to enter this mode.
Then, this mode operates with
display of Icon on LCD.
This programmable option
e n abl e s you r ve h i c l e t o
automatically lock the doors in 30 seconds after the vehicle
has been started with a key while all the doors are closed.
On the contrary, the vehicle will automatically unlock the
doors upon pulling the key out from the ignition.
Please press button ( + ) simultaneously for 2 seconds
and then press button for 0.5 second again to exit.

19
4. Mute
Press button ( + )
simultaneously for 2 seconds
and then press button for
0.5 second. to enter this mode,
and then all the Icons displayed
on LCD disappear and the
siren does not operate. The
siren, however, operates in
other modes ((example) Panic, Shock, Theft) even in Valet
mode.
In this mode, Siren does not operate during arming and
disarming only.
If you press button ( + ) simultaneously for 2 seconds
and then press button for 0.5 second again, all the Icons
will appear again with siren operate.

5. Reservation start (On/Off)

Press the button ( + ) for 2
seconds and release and then
press for 2 seconds. Then
icon appears on the screen.
From then on, the vehicle start
automatically at reserved time
in every 24 hours.

6. Turbo

20/ USER'S GUIDE

6-1

Press ( + ) for 2 seconds

and release, the press the button
for 0.5 second and release.
In this mode, engine continues
to run for a selected time of 30
seconds or 2 minutes (you can
change the setting in option
menu).
This is very useful for turbo charged vehicles to cool down
the mechanical components after driving.
To exit, follow the same procedure above again.

6-2 Start button model

In the mode, engine continues to run for a selected time of
30 seconds or 2 minutes (you can change the setting in
option menu).
① Please follow the step on the remote as above.
② While the engine is running, activate the parking brake
(auto transmission) or the emergency brake (manual
transmission)
③ While pressing the foot brake on, press start button for 1
second and then release. The remote chirps and the
parking lights flash once each(for from the key box).
④ The engine keeps running and the start button's LED
rotates diagonally.
⑤ Open the door and close
⑥ T he engine additionally runs for 30 seconds (or 2
minutes, changed in option)

21
7. Shock sensor by-pass
7-1
Press button ( + )
simultaneously for 2 seconds and
release, and then continuously
press the button for 2
seconds to deactivate the shock
sensor.
You can find the Icon on
LCD to confirm this mode.
This function can be used, when you do not want it.
example) when you sleep in the vehicle, when baby sleeps in
the vehicle, when you let your pet stay in the vehicle.

7-2
Press button ( + ) simultaneously for 2 seconds and
release, and then continuously press the button for 2
seconds to activate the shock sensor.
The Icon on LCD disappers to confirm this.
If your vehicle is shocked whele your vehicle is armes and
the engine is turned off, your vehicle chirps and sends signal
to your remote with the blinking icon on LCD.

8. Smart Door
Press button ( + ) for 2 seconds and release. And then
continuously press the button ( + ) for 0.5 second.
then icon appers on the LCD. To please do the same

22/ USER'S GUIDE

 process again.
The doors are unlocked when
the car owner with the remote
approaches the vehicle and
locks the vehicle after 10
seconds when the car owner
with the remote is far enough
away from the vehicle.
* T his function is unavailable
when the door is open or the
vehicle is running.

9. Current Time Change

① When you press the button (
+ ) for 2 seconds and
release and then continuously
press the button ( + )
for 2 seconds and release, the
current time flashes and
ready to change.
② If you press for 0.5
second, the hour changes
③ If you press for 0.5 second, the minute changes
④ After you adjust the current time, please press the button
for 0.5second and release (or press ( + ) for 2
seconds and release), with the melody from the remote,
the setup is completed.
* If you want to get out of setup mode, stay for 7 seconds
while the current time blinks.

23
10. Reserved Time Change
① When you press the button (
+ ) for 2 seconds and release
andthencontinuouslypressthe
button ( + ) for 2 seconds
and release, the current time
flashes and ready to change.
② I f you press for 0.5
second, the hour changes
③ If you press for 0.5 second, the minute changes
④ After you adjust the current time, please press the button
for 0.5secound and release (or press ( + ) for 2
seconds and release), with the melody from the remote, the
setup is completed.
* If you want to get out of setup mode, stay for 7 seconds while
the current time blinks.

[ EASY Option Setup ]

You can make the opton change easily by looking at icons on
display.
① Press the button ( + ) for 2 seconds and then release.
The siren chirps and the parking light flashes once.
Button Option Button Icon

0 Time Start Time 15 Min ↔ 25 Min

24/ USER'S GUIDE

 Button Option Button Icon

1 Time Turbo Time 30 Sec ↔ 2 Min

2 Times Siren Time 30 Sec ↔ 60 Sec

Preheating 4 Sec → 7 Sec → 10 Sec →
3 Times
Time 15 Sec → 4 Sec
Low battery OFF → 11.5V → 12.0V →
4 Times
start (option) 11.5V → OFF

② Press the button for 0.5 second and then release to

move to another option
③ Press the button for 0.5 second and then release to
change the option setting
④ Press the button for 2 seconds and release to save the
change. The siren chirps and the parking lights flash once
if the change is saved safely.

[ Others ]

1. Real Time Remote Paging Functions

Owner Call, Theft report and Shock Sensing report
whenever one of these is triggered, it is reported to the
remote with beeps and flashing icons on LCD.
In particular, Theft is reported with continuous beeps and
with one of the icons such as door,trunk and hood in
consideration that you didn't hear the beeps.

25
 1-1 Owner Call Mode
This mode allows other people to call you by knocking 2
times on the front window of the vehicle.
You can recognize this call by 4 times of bell sound.
If you press button ( + ) for 0.5 second to confirm it,
your vehicle flashes the parking lights once.

1-2 Shock Sensing Report Mode

This function reports to your remote that your shock sensor
on the vehicle has been triggered during the arming mode.
When the shock sensor is triggered, your remote makes
warning sounds until you press button to stop the
warning.

1-3 Theft Report Mode

The system recognizes any theft, and activates alarm when
doors open by force or with the key while the vehicle is
armed.
Siren chirps and remote warns continually in theft mode.
The siren in your vehicle operates even in silent siren mode
and chirps for 30 seconds. The duration can be changed to
60 seconds on the optional setting.
Press button to confirm and stop the report and siren.

2. Adjusting the sensitivity of shock sensor

Please ask your installer for the location of your shock
sensor. You can adjust the sensitivity of the shock sensor by
turning the knob on the shock sensor. Turn the knob on the

26/ USER'S GUIDE

 shock sensor clockwise for higher sensitivity and counter
clockwise for lower sensitivity.

Note
Do not turn the knob with excessive force, or beyond its limit.
Shock sensor is fragile.

3. Reservation mode(For Manual Transmission Vehicle)

3-1 What is 'Reservation mode'?
In order to remote-start your manual transmission vehicle,
you must first set up reservation mode before leaving your
vehicle. The purpose of leaving the transmission gear in the
neutral position is to prevent your vehicle from moving
forward while remote starting. You should set reservation
mode each time you turn off your vehicle.
1) Important requirements to activate Reservation mode :
① The transmission must be in neutral position
② All doors must be closed
③D  o not set the reservation mode with passengers or pets
inside the vehicle
2) Remote Start does not operate without setting Reservation
mode. If you press and hold button to remote start
your vehicle without setting the Reservation mode, remote
chirps 3 times and parking lights flash 3 times. Parking

27
 lights will flash 7 times more to let you know that it failed to
remote start.

Note
RESERVATION MODE IS NECESSARY FOR YOUR OWN
SAFETY.

3-2 Automatic Reservation Mode (Default Setting)

How to set Automatic Reservation mode:
① Place the transmission in neutral position before you
turn the engine off
② Activate emergency brake
③ Press the start button for 1 secound, the engine will
keep running. Also the start button’s LED rotates
diagonally.
④ Exit the vehicle and close all doors
⑤ The engine will automatically turn off and reservation
mode is completed
The reservation mode is, however, cancelled if doors are
open or valet mode is activated. Once cancelled, you have
to start your vehicle with the manual key and repeat the
step 1 to 5 to restore the Reservation mode.

3-3 M
 anual Reservation Mode (Optional setting)
Please follow the steps ①~⑤ above press the button
for 2 seconds, open and close the door. The next step is
same as the rest.

4. Easy Door Lock (option)

28/ USER'S GUIDE

4-1
The door can be locked or unlocked
without remote or the vehicle key. If
the 4 digit password is inputted, it
arms or disarms the vehicle.
10 blue LEDs display various
functions: such as arming,
disarming, valet mode, and
emergency status. If anyone knocks twice on the LEDs on the
windshield, remote receives the call signal (optional Owner
call mode).

4-2 How to input the 4 digit password

①T urn the engine off, and place the car key to the ON
position. Open the door and wait until the light moves
from number 1 LED.
②N umber 1 LED will be on for 2 seconds and OFF, and it
will repeat on each number from 2 to 0.
③ If you knock once while your desired number LED
lights up, LED will flash and repeat step 2 above.
④Y ou have to repeat the step 2 and 3 for 3 more times to
enter a 4 digit password.
For Example, if your desired password is 2, 3, 4, and 5,
then wait until number 2 LED lights up and gently knock
on the sensor. After this, number 1 LED will light up and
continuously move to next number, and knock on the
sensor when number 3 LED lights up. Repeat this process
for number 4 and 5 to finish enter your password.

4-3 D
 oor Lock / Unlock

29
 ① Wait, the light moves from number
1 LED during lock, unlock or valet
mode.
② Number 1 LED will be on for 2
seconds and off, number 2 led will
be on 2 seconds and off, and it will
continuously move around to 0.
③ Knock on the sensor once on your first digit of your
password, light will flash once more to confirm the
recognition.
④ Repeat the step 3 for your second, third and forth number
of your password.
⑤ After your forth password, vehicle will lock (if it was
unlocked), or unlock (if it was locked).
During Valet mode, doors can lock or unlock only.
In case that the incorrect passwords are inputted more than 5
times, Easy Door Lock will not be functional for 20 minutes.

4-4 L
 ED Display
① D uring Arming: From (9) to (3), the 5 LEDs will
sequentially flash five times left to right, and right to left
(9-0-1-2-3-2-1-0-9-0). After that, LEDs will be on for 2
seconds each from number 1 to 0, and you can enter your
password, while each LED is on for 2 seconds.
② If alarm was triggered during the arming mode, LED will
flash rapidly in sequence above after the siren duration.
③ D uring the siren duration, all LED will flash
simultaneously
④ During disarming: (0) Led will flash five times every 3
seconds.
⑤ During Valet mode: (0) Led flashes every 10 seconds.

30/ USER'S GUIDE

5. Parking Timer / Car temperature check / Car
Voltage chek
If you press the button ( + ) for 0.5 second, appears by
turn parking timer, car temperature & car battery voltage.

6. Charging time alert

: Normal working
: The display is 50% dimmer
: Button vibration not available
: Button vibration not available
: No reception from car. Transmitting from remote is
okay
The display is 75% dimmer
Battery shortage warning
7. Reset
RESET Press the reset hole with sharp
needle for 0.5 second when the
remote shows some problem.

1141 Budapest, Fogarasi út 77. 1095 Budapest, Mester u. 34.

Tel.: *220-7940, 220-7814, 220-7959, Tel.: *218-5542, 215-9771, 215-7550,
220-8881, 364-3428 Fax: 220-7940 216-7017, 216-7018 Fax: 218-5542
Mobil: 30 531-5454, 30 939-9989 Mobil: 30 940-1970, 20 949-2688

www.delton.hu
E-mail: [email protected] Web: www.delton.hu