ANSI, CLT & CLB

CHEMICAL PROCESS PUMPS

CONTENTS

ANSI

Application 2

Design & Construction 2

Materials of Construction 3

Model Description 3

Interchangeability Guide 4

Sectional Drawings & Parts List 5

Construction Details 7

Pump Dimensions 8

Tombstone Curves 9

CLT

Application 10

Design & Construction 10

Materials of Construction 10

Model Description 10

Sectional Drawings & Parts List 11

Pump Dimensions 12

Tombstone Curves 14

CLB

Application 15

Design & Construction 15

Materials of Construction 15

Model Description 16

Sectional Drawings 16

Sectional Drawings & Parts List 17

Pump Dimensions 18-20

Tombstone Curves 21

1
 ANSI
HEAVY-DUTY PROCESS PUMPS

APPLICATION
• Chemical
• Petrochemical
• Pulp & Paper
• Primary metals
• Pharmaceutical
• Textile
• Food

RA Pump Minimum Maximum Minimum Maximum Maximum

Range Flow (m3/h) Flow (m3/h) Head (m) Head (m) Temperature

ANSI 2 900 3 140 260˚C

DESIGN & CONSTRUCTION

• Single stage end suction centrifugal pump with is inherent in full shroud designs. It is matched to
fully open impeller allowing it to handle solids up casing for high efficiency and enables excellent
to 25mm. passage for solids.

• Back pull out feature allows for the removal of the • The open vane design has large smoothly
entire rotating assembly without disturbing the contoured flow passages, which minimize NPSH
suction and discharge pipe work. requirements.

• The volute casing has horizontal suction and • Wear adjustment within the bearing assembly
vertical discharge flanges. design allows for hydraulic performance to be
maintained by an external impeller adjustment, thus
• Available in a wide range of materials (including giving extended maintenance intervals on the pump.
special alloys)
Stuffing Box Cover
This pump offers a wide variety of features: • The Cover can be supplied with a jacket for cooling
the stuffing box chamber in high temperature
Casing services.
• Axial suction and radial vertical discharge,
foot supported for maximum resistance to pipe • The jacket can also be used for heating viscous or
misalignment and distortion. high freezing point liquids.

• 150lb flanges as standard and for heavy duty • It is equipped with a Quench Gland and the gland
applications 300lb flanges are optional (ANSI B16.5). follower is split for easy removal. Tapped openings
to lantern ring permit “in and out” sealing and
• Gauge and drain plug openings are supplied when external flush of lubrication as required.
specified.
• Stuffing box is completely machined for mechanical
Impeller seal installation, either originally or as a field
• The impeller is fully open with partial shrouds for conversion.
maximum vane support without the high thrust that
2
 ANSI
HEAVY-DUTY PROCESS PUMPS

• Internal, external, double- or balanced seals, with Other construction materials available for
any required gland, restricting bushing and specialised applications:
flushing lines furnished to meet individual sealing CD4MCu: Cast Chrome - Nickel Alloy
needs. - ASTM A 890 CD4MCU
GA-20: Cast Alloy 20 ASTM A 743 CN7M
Frame Adapter Monel: Cast Monel ASTM A 494 M35-1
• Contains non-sparking rotating deflectors, and Nickel: Cast Nickel ASTM A 494 CZ100
in-board bearing oil seal. Hast-C: Cast Hast-C ASTM A 494 CW12MW
Hast-B: Cast Hast-B ASTM A 494 N12MV
• Adapter may be piped to drain. Model ANSI 343 WCB: Cast Steel ASTM A216-03 WCB
adapter on 6” diameter sizes is cast integral with
bearing frame.
MODEL DESCRIPTION
Bearing Frame
• Heavy-duty cast-iron construction with large oil ANSI 3 x 4 - 13 S S M
reservoir and water jacket.
Sealing Arrangement
• The Oil level is monitored by sight glass. Oil seals Impeller Material
on each end and oil breather fully protect oil from Volute Material
contamination while allowing for expansion and Normal Impeller
contraction of air caused by ambient temperature Suction Flange
change (bearing isolators – optional). Discharge Flange
Pump type
Shaft
• Designed for 0,05mm maximum deflection at
stuffing box face. All bearing and packing surfaces
are factory machined to high tolerances.

Shaft Sleeve
• Renewable shaft sleeve is fitted with one end free
to expand with temperature variations while Teflon
O-ring prevents leakage under the sleeve.

Bearings
• Inboard bearing single row, deep groove is pressed
on shaft and is free to float axially in frame-carrier.

• Outboard bearing is double row, deep groove

angular contact shouldered and locked onto shaft
in the bearing housing enabling it to carry any
radial and unbalanced thrust loads.

MATERIALS OF CONSTRUCTION
Shaft: 316 Stainless steel
Impeller: 316 Stainless steel
Volute: 316 Stainless steel
Bearing Bracket: Cast iron
Frame Adaptor: Cast iron
Stuffing Box: 316 Stainless steel
Shaft Sleeve: 316 Stainless steel

3
 ANSI
HEAVY-DUTY PROCESS PUMPS

INTERCHANGEABILITY GUIDE
Casing Cover volute - nominal impeller delivery
Shaft and branch bearing
Bearing Frame Shaft unit bracket
size
Assembly Adapter Stuffing box Impeller Casing ID

1 x 1½ - 6

ANSI
343
1½ x 3 - 6
22mm Shaft
Max.kW - 30

2x3-6

1 x 1½ - 8
ANSI
343
22mm Shaft
Max.kW - 30 1½ x 3 - 8

2x3-8

ANSI
495
3x4-8
45mm Shaft
Max.kW - 91

3 x 4 -8G

1 x 2 - 10

1½ x 3 - 10

ANSI
495
2 x 3 - 10
45mm Shaft
Max.kW - 91

3 x 4 - 10

4 x 6 - 10

1½ x 3 - 13

ANSI 2 x 3 - 13
495

45mm Shaft
Max.kW - 91
3 x 4 - 13

4 x 6 - 13

6 x 8 - 13

8 x 10 - 13

ANSI
708
6 x 8 - 15
60mm Shaft
Max.kW - 110

8 x 10 - 15

8 x 10 - 15G

4
 ANSI
HEAVY-DUTY PROCESS PUMPS

SECTIONAL DRAWING
HEAVY-DUTY DESIGN FEATURES FOR TOTAL RANGE OF PROCESS SERVICE
13 1 2
MODEL ANSI 708/495
228 A 113 A 122 123 210 370 B 353 108 355 107 370

100
361 A 351
126 122 A 184 A
496 370 H
101
370 C
105
106
134 A

4
12112 A
136
332 A

11
5
370 D

Optional Jacketed Stuffing Box.

Shaft Sleeve is Standard. 168 A

412 A
370 F
184

241
10
469 B 333A
9
418 8 7 6

Available on all Model ANSI Pumps

6 4 5 3

DESCRIPTION DESCRIPTION DESCRIPTION

1 MAXIMUM SEALING FLEXIBILITY 5 POSITIVE LIQUID SEALING AT IMPELLER 10 OIL LUBRICATION STANDARD
• Choice of packed gland or mechanical seal. • Teflon “O” Ring in controlled compression protects • Rugged bearing housing vent . Grease lubrication
• Any make - inside or outside - single, double threaded area against corrosion. optional.
and balanced. • Metal contact between shaft and impeller transmits • Large cooling jacket assures lower bearing
torque and assures perfect alignment. temperature on high temperature services.
2 HEAVY WALLED CASING
• Oil return drains under bearings assure uniform oil
• To resist pipe loads and corrosion 6 CASING DRAIN OPTIONAL
circulation through bearings.
• 150 pound flanges standard
• 300 pound flanges optional 11 CONTINUOUS HIGH PERFORMANCE
7 POSITIVE SEALING AT CASING JOINT Maintained by external impeller adjustment – simple
3 RENEWABLE SHAFT SLEEVE STANDARD • With fully confined gasket. and fast with open end wrench . no shimming required.
• Simplifies maintenance - Renew sealing surface • Alignment fit protected from liquid.
without shaft and bearing disassembly 12 HIGH THRUST CAPABILITY
8 ACCURATE MACHINED FITS MEAN POSITIVE With double row thrust bearing and shaft lock nut.
• Teflon “O” Ring protects shaft against liquid contact ALIGNMENT
Minimum shaft end play for effective stuffing box
JACKET STUFFED BOX OPTIONAL • Accurate alignment of impeller to casing provides
sealing. Bearings sized for 2 year minimum life.
• For cooling packing or seal in temp. to 2600C. maximum hydraulic efficiency.
• Concentricity of shaft to stuffing box bore assures
4 SEMI OPEN IMPELLER low sealing maintenance. 13 BEARING HOUSING
• With expeller vanes, smoothly contoured for slurry Sealed to prevent contamination from corrosive
handling and to meet low NPSH requirements. 9 HEAVY-DUTY SHAFT atmosphere, leakage and wash – down.
• Original clearance maintained by external adjustment. • Designed for tough services. Maximum: 0.05mm Double-lip seals are provided as standard for extended
deflection at stuffing box face at maximum load. service life.
• Renewable shaft sleeve standard. Bearing isolators may be provided as an option.

5
 ANSI
HEAVY-DUTY PROCESS PUMPS

SECTIONAL DRAWING
MODEL ANSI 343 496 361 A 113 A 168 A 119 A 123 184 412 A 351

100

370 C 101

112 A

136

503
332 A

134 A

370 D

Assembly View of 1x1½-8 & 1½x3-8

228 A 333 A 122 210 353 355 370 H 370 107 105 106

PARTS LIST
Per Pump

Per Pump
No. Reqd.

No. Reqd.
Number

Number

Part Description Materials Part Description Materials

Item

Item

105 1 Lantern Ring 316SS 261 1 Gasket - Adapter to Stuffing Box Valumoid
106 1 Set Stuf fing Box Packing P.T.F.E 332A 1 Oil Seal - Coupling End Buna Rubber
107 1 Gland Follower 316SS 333A 1 Oil Seal - Inboard End Buna Rubber
108 1 Frame Adaptor Cast Iron 351 1 Gasket - Casing Valumoid
109A 1 Bearing End Cover - Coupling End Cast Iron 353 2 Gland Stud 316SS
112A 1 Ball Bearing - Outboard End Steel 355 2 Gland Stud Nut 304SS
113A 1 Bearing Frame Breather Non Metallic 360C 1 Gasket - Brg. End Cover to Brg. Housing Valumoid
119A 1 Bearing End Cover - Inboard Steel 260D 1 Gasket - Bearing Frame to Adapter Valumoid
122 1 Pump Shaft (Less Sleeve) 316SS 361A 1 Circlip Steel
122A 1 Pump Shaft (With Sleeve) 316SS 370 4-24 Cap Screw - Frame/Adaptor to Casing 304SS
123 1 Deflector Glass Reinforced Nylon 370B 4 Cap Screw - Adapt./Adapt. Ring to Frame Steel
126* 1 Shaf t Sleeve 316SS 370C 3-4 Tap Bolt - Bearing Housing Steel
134A 1 Bearing Housing Cast Iron 370D 3-4 Tap Bolt - w/Lock Nut - Impeller Adjust. Steel
136 1 Bearing Locknut Steel 370F 1-2 Cap Screw - Frame Foot Steel
168A 1 Ball Bearing - Inboard Steel 370H 2 Stud Nut - Cover to Adapter 304SS
184 1 Stuffing Box Cover - Standard 316SS 371D 8 Cap Screw Steel
184A 1 Stuffing Box Cover - Water Jacketed 316SS 412A 1 “O” Ring - Impeller Teflon
210 1 Gland Packing Valumoid 418 2-3 Tap Bolt - Jacking Steel
228A 1 Bearing Frame Cast Iron 469 2 Dowel Pin - Frame to Adapter Steel
241 1 Bearing Frame Foot Cast Iron 496 1 “O” Ring - Bearing Housing Buna Rubber
Slight Glass (Not Shown) Polycarbonate 503 1 Adapter Ring Cast Iron

6
 ANSI
HEAVY-DUTY PROCESS PUMPS

CONSTRUCTION DETAILS
POWER END ANSI 343 ANSI 495 ANSI 708
AT IMPELLER 19 mm 25 mm 38 mm
SHAFT IN STUFFING BOX (WITH SLEEVE) 1.375" 1.75" 2"
DIAMETERS SLEEVE OUTSIDE DIAMETER 1.375" 1.75" 2.5"
BETWEEN BEARINGS 38 mm 54 mm 79 mm
AT COUPLING 24 mm 32 mm 60 mm
BEARINGS RADIAL TYPE 207-S TYPE 309-S TYPE 313-S
COUPLING END (DOUBLE ROW) 5306 mm 5309 mm 5313 mm
BEARING SPAN 105 mm 171 mm 235 mm
SHAFT OVERHANG 156 mm 213 mm 253 mm
BORE 50.8 mm 63.5 mm 86 mm
DEPTH 54 mm 67 mm 76 mm
STUFFING BOX
PACKING SIZE 8 X 8 mm 10 X 10 mm 11 X 11 mm
NO OF RINGS 5 5 5
WITDH OF LANTERN RING 11 mm 16 mm 16 mm
DISTANCE - END OF BOX TO NEAREST OBSTRUCTION 55 mm 76 mm 74 mm

ANSI 343 ANSI 495 ANSI 708

8 x 10-15G
1½ x 3-13

8 x 10-13

8 x 10-15
1½ x 3-10
PUMP END
1 x 1 -8

1 x 1 -8
1 x 1 -6

3 x 4-8G
1 x 3-6

1 x 2-10

2 x 3-10

3 x 4-10

4 x 6-10

2 x 3-13

3 x 4-13

4 x 6-13

6 x 3-13

6 x 8-15
2 x 3-6

2 x 3-8

3 x 4-8

MAIMUM DIAMETER SOLIDS 8 11 9 8 11 12 28 17 11 5 9 15 25 5 9 15 25 17 25 20 28 20

3500 R/MIN 3 6,2 7 6 7,8 8,6 - 15 7,2 8,6 9,8 15 - 10 16 35 - - - - - -
SHAFT DEFLECTION
1750 R/MIN 0,8 1,6 1,8 1,5 2 2,2 7 4,1 1,9 2,2 2,5 4,1 17 2,6 4,6 12 17 8 15 10 - 30
LOAD FACTOR (M)
1150 R/MIN 0,3 0,7 0,8 0,7 0,9 1 3 1,8 0,8 1 1,1 1,7 6,8 1,2 1,9 5 6,8 3,6 6,7 4,5 12 14
MAXIMUM CASING THICKNESS 9,5 11 12,7 39 41 12,7 39
CASING CORROSION ALLOWANCE 3 3 3
WORKING PRESSURE SEE PRESSURE - TEMPERATURE CHART
TEST PRESSURE 150 % pf WORKING PRESSURE AT 20˚C
MAXIMUM LIQUID TEMPERATURE* 175 ˚C
MAXIMUM LIQUID TEMPERATURE** 260 ˚C
UNIT MASS SEE DIMENSIONS

*WITHOUT COOLING
**WITH COOLING

PRESSURE - TEMPERATURE RATINGS PRESSURE - TEMPERATURE RATINGS

WITH 300 POUND ANSI FLANGES WITH 150 POUND ANSI FLANGES
-200 -100 0 100 200 300˚C -200 -100 0 100 200 300˚C
300
D, E, F, J Curve Material ASTM Designation
200
A A Ducktile Iron A395
B 316SS A744-CF-8M
C GA-20 A744-CN-7M
B
250 D Hast-B A494-N-12M-2
E Hast-C A494-CW-12M-2
F CD4MCu A744-CD-4MCu
3000 1500 G Monel A744-M-35
C H Nickel A744-CZ-100
400 200
C A K

DE
H F G
300 150
B G 2000 1000
C B

D
E A H
200 F 100
G
H
1000 500

100 50

0 0 0 0
-400 -200 0 200 400 600˚F -200 0 200 100 600˚F
TEMPERATURE TEMPERATURE

7
 ANSI
HEAVY-DUTY PROCESS PUMPS

DIMENSIONS
A F Z

h2

h1

Y E E

DIMENSIONS DETERMINED BY PUMP

Nominal Nominal Shaft KEY- Pump
MODEL PUMP SIZE Discharge Suction h2 F A h1 Z Dia. WAY Mass
Size in “ Size in “ at Cplg. kg

1 X 11/2-6 1 11/2 165 343 102 133 184 76 100 24 8X7 39

11/2 X 3-6 11/2 3 165 343 102 133 184 76 100 24 8X7 42
ANSI 2 X 3-6 2 3 165 343 102 133 184 76 100 24 8X7 44
343 1 X 11/2-8 1 11/2 165 343 102 133 184 76 85 24 8X7 46
11/2 X 3-8 11/2 3 165 343 102 133 184 76 85 24 8X7 49
2 X 3-8 2 3 241 495 102 210 318 124 85 32 10X8 91
3 X 4-8 3 4 279 495 102 210 318 124 85 32 10X8 100
3 X 4-8G 3 4 279 495 102 210 318 124 85 32 10X8 100
1 X 2-10 1 2 216 495 102 210 318 124 110 32 10X8 91
11/2 X 3-10 11/2 3 216 495 102 210 318 124 110 32 10X8 100
ANSI 2 X 3-10 2 3 241 495 102 210 318 124 110 32 10X8 105
495 3 X 4-10 3 4 279 495 102 254 318 124 110 32 10X8 120
4 X 6-10 4 6 343 495 102 254 318 124 110 32 10X8 139
11/2 X 3-13 11/2 3 267 495 102 254 318 124 95 32 10X8 112
2 X 3-13 2 3 292 495 102 254 318 124 95 32 10X8 125
3 X 4-13 3 4 318 495 102 254 318 124 95 32 10X8 150
4 X 6-13 4 6 343 495 102 254 318 124 95 32 10X8 185
6 X 8-13 6 8 406 708 152 368 476 203 133 79 23X8 254
ANSI 8 X 10-13 8 10 457 708 152 368 476 203 133 79 23X8 304
708 6 X 8-15 4 8 457 708 152 368 476 203 133 79 23X8 277
8 X 10-15 4 10 483 708 152 368 476 203 133 79 23X8 336
8 X 10-15G 4 10 483 708 152 368 476 203 133 79 23X8 322
Flanges are drilled to ANSI B16.5 flange dimensions.

TAPPED OPENING INDICATES ITEMS FURNISHED STANDARD

TAP SIZE
PUPOSE NO OF TAPS
ANSI 343 ANSI 495 ANSI 708
LANTERN RING CONNECTOR 2 1/4 " 3/8 " 3/8 "
FRAME ADAPTER DRAIN 1 SLOT 1" 1"
CASING DRAIN (WITH ASBESTOS GASKET) 1 13/8 " 13/8 " 13/8 "
ALTERNATE CASING DRAIN 1 1/2 " 1/2 " 1/2 "
BEARING FRAME CONTROL 4• 1/2 " 1/2 " 1/2 "
DISCHARGE GAUGE CONNECTION 1 1/4 " 3/8 " 3/8 " R/MIN
MODEL 3560 2900 1780 1450 1180 880
SUCTION GAUGE CONNECTION 1 1/4 " 3/8 " 3/8 "
ANSI 343 30,0 24,4 14,9 12,1 9,9 7,4
STUFFING BOX CIRCULATING LINE 1 1/4 " 3/8 " 3/8 "
ANSI 495 91,0 74,0 45,5 37,1 30,2 22,5
QUENCH GLAND CONNECTION 2 1/4 " 1/4 " 1/4 " ANSI 708 - - 186,4 152,1 123,8 92,5
• 4 x 6 - 10 & 4 x 6 - 13 have no tap, 3 x 4 - 13 have 1/4” tap.
8
 ANSI
HEAVY-DUTY PROCESS PUMPS

TOMBSTONE CURVES

1450 rpm
Pg. no.
50 Size*

6x
8-1 1x1½-6 2 24
5
40 8x
10- 1x1½-8 3 25
15
G
8x 1½x3-6 4 26
3x 10-
4 -1 15
3 1½x3-8 5 27
2x
11/2 3 -1
30 x3 3 8x 1½x3-10 6 28
-13 10-
13 1½x3-13 7 29
HEAD [m]

6x
8-1
3 1x2-10 8 30
4x
1x 6-1 2x3-6 9 31
20 2-1 2x 3x 3
0 3-1 4 -1
1 1/
2
0 0 2x3-8 10 32
x
3-
2x 10 2x3-10 11 33
10 1x
11/ 3-
8 3x 4x
2x3-13 12 34
2-
8 11
3x 4- 6-1
2/
x
3-
8 4- 8 0
8G 3x4-8G 13 35
1
x
1 1/
2-
6 3x4-8 14 36
11/2 x 3-6 2 x 3-6
3x4-10 15 37
3x4-13 16
4x6-10 17
4x6-13 18
10 20 40 60 80 100 150 200 300 400 500 600 800 1000
6x8-13 19
FLOW RATE [m3/h] 6x8-15 20
8x10-13 21
8x10-15G 22
2900 rpm
8x10-15 23
150

11/2 x 3-13 2 x 3-13

100
90
1 x 2-10
80 11 3 x 4-13
2/ x
3- 2 x 3-10
70
HEAD [m]

10
3 x 4-10
60 2x
3-8
50 1x 11/2-8
3 x 4-8
40 3 x 4-8G
11/2 x 3-8
30
1 1/
2x
20 3-6
1x 11/2-6 2 x 3-6
10 BEST EFFICIENCY POINT SHOWN

0 10 20 40 60 80 100 150 200 250

FLOW RATE [m3/h]

* FOR INDIVIDUAL PUMP PERFORMANCE CURVES, REFER TO OUR ANSI CURVES BOOK.

9
 CLT
MEDIUM-DUTY CENTRIFUGAL CHEMICAL PUMPS TO EN ISO 22858 (DIN 24256)

APPLICATION
• Pharmaceutical
• Food and Beverage
• Air Conditioning
• Paints and Inks
• Steel Manufacturing
• Chemical Industry

Maximum
RA Pump Minimum Maximum Minimum Maximum Maximum
Temperature
Range Flow (m3/h) Flow (m3/h) Head (m) Head (m) Temperature

160˚C
CLT 2 1050 3 140 180˚C

DESIGN & CONSTRUCTION

• Single stage, end-suction and of modular design with • Shaft is supported by sealed for life deep groove
a high interchangeability of parts. ball bearings, allowing for a maintenance free life cycle.

• Suitable for pumping clean liquids and highly • Bearing assemblies from our EN 733, NT-Range are
aggressive chemicals. utilized allowing a high interchangeability of spares.

• Excellent hydraulic performance with low N.P.S.H

required values. MATERIALS OF CONSTRUCTION
• The suction flange is horizontal and the discharge is Pump shaft: Grade 316 Stainless steel
vertical. Volute casing: Grade 316 Stainless steel
Impeller: Grade 316 Stainless steel
• Standard flanges conform to DIN 2543 PN16. Gland plate/seal plate: Grade 316 Stainless steel
Bearing assembly: Cast Iron
• The wet end components of the pump (Volute,
Impeller and Seal or Gland Plate) are supplied
standard in high grade Cast Stainless Steel for long MODEL DESCRIPTION
life.
CLT 32-200 S S M
• They have overhung impellers, hydraulic balance is
effected by balance holes in the impeller. Standard Sealing Arrangement
construction is with soft packed stuffing box or single, Impeller Material
unbalanced mechanical seal. Volute Material
Nominal Impeller Diameter in mm
• The entire range offers a high interchangeability, Discharge Size in mm
thus reducing spares stock holding. Pump type

• Back pull out feature for ease of maintenance,

allowing the volute casing to remain connected to
the pipework when removing the rotating assembly.
10
 CLT
MEDIUM-DUTY CENTRIFUGAL CHEMICAL PUMPS TO EN ISO 22858 (DIN 24256)

SECTIONAL DRAWING
458.1 908.1 461.1 970.1 920.1 560.1 902.1 452.1 557
411.2

PM2 903.2 PM3

400.4

400.1 360.2

161.1 932.2

230.1 940.2

930.1

922.2

940.1

102.1 400.2 509.1 908.1

400.1 908.2

470.1 Design with

intermediate ring

903.1 411.1 507.1 361.1 914.4 360.1 330.1 321.1 932.1 321.2 183.1 901.1 914.4 210.1

FD LO

361.1 360 400.4 557 551.7 321.1 330 932.2 321.1 400.4 360 551.3 932.1 361.1

361.1 400.4 557 321.1 932.1 551.3 932.2 321.1 551.3 400.4 932.1 361.1

DRIVE DRIVE
END END
NT 530 NT 585

PARTS LIST
VOLUTE CASING 102.1 DISTANCE WASHER 551.1 GL AND 452.1
GL AND/SEALPL ATE 161.1 DISTANCE WASHER 551.2 L ANTERN RING 458.1
SUPPORT FOOT 183.1 WAVE WASHER 557.0 PACKING RING 461.1
SHAFT 210.1 HEXAGON SCREW 901.1 MECHANICAL SEAL 470.1
IMPELLER 230.1 STUD BOLT 902.1 FLINGER RING 507.1
GROOVE BALL BEARING 321.1 SCREW PLUG 903.1 MATCHING RING 509.1
GROOVE BALL BEARING 321.2 SCREW PLUG 903.2 SPRING WASHER 930.2
BEARING BRACKET 330.1 SET SCREW 908.1 CIRCLIP 932.1
BEARING COVER 360.1 SET SCREW 908.2 CIRCLIP 932.2
BEARING COVER 360.2 SOCKET HEAD CAP SCREW 914.4 KEY 940.1
OIL SEAL 361.1 HEX. NUT. 920.1 KEY 940.2
GASKET 400.1 IMPELLER NUT 922.2 CUP SPRING 950.2
GASKET 400.2 SPRING RING 930.1 NAME PL ATE 970.1
GASKET 400.4

11
 CLT
MEDIUM-DUTY CENTRIFUGAL CHEMICAL PUMPS TO EN ISO 22858 (DIN 24256)

DIMENSIONS

a f x b1 b2

PM2 bf
PM3 DNd
bf

Key acc. to
DIN 6885
t u

d
c

s
d
m2 LO BI e
FD
m1 n2

w n1

kf Arrangement
CONNECTIONS
4 holes
B1 Flushing - Inlet Special
FD Fluid Drainage Special
LO Leakage - Outlet G 3/8
PM2 Pressure Measurement Special
PM3 Pressure Measurement Special
m3

Arrangement Flanges acc. to

d 2f 8 holes DIN 2543/PN16
DNs Df bf kf d2f
DNd Holes
25 115 18 85 4 14
kf Arrangement 32 140 18 100 4 18
12 holes 40 150 18 110 4 18
50 165 20 125 4 18
65 185 18 145 4 18
80 200 20 160 8 18
100 220 20 180 8 18
125 250 22 210 8 18
150 285 22 240 8 22
Arrangement 200 340 24 295 12 22
d 2f 250 405 26 355 12 26
16 holes

12
 CLT
MEDIUM-DUTY CENTRIFUGAL CHEMICAL PUMPS TO EN ISO 22858 (DIN 24256)

DIMENSIONS

Suction Pressure Pump Dimensions Foot Dimensions Shaft End

Flange Flange Extension Corresponds
Bolts Dimension acc. to DIN 748 to DIN 24255
Size
DNs DNd a f b1 b2 h1 h2 b c c1 e m1 m2 m3 n1 n2 n3 n4 w s x d l t u
25-160 40 25 80 360 128 128 132 160 50 15 4 28 100 70 45 240 10 160 110 260 M12 100 24 50 27 8
25-200 40 25 80 360 132 132 160 180 50 15 4 28 100 70 45 240 190 160 110 260 M12 100 24 50 27 8
32-160 50 32 80 360 130 130 132 160 50 15 4 28 100 70 45 240 190 160 110 260 M12 100 24 50 27 8 •
32-200 50 32 80 360 130 135 160 180 50 15 4 28 100 70 45 240 190 160 110 260 M12 100 24 50 27 8 •
32-250 50 32 100 470 170 170 180 225 65 15 4 28 125 95 45 320 250 160 110 340 M12 100 32 80 35 10
40-160 65 40 80 360 130 130 132 160 50 15 4 28 100 70 45 240 190 160 110 260 M12 100 24 50 27 8 •
40-200 65 40 100 360 130 140 160 180 50 15 4 28 100 70 45 265 212 160 110 260 M12 100 24 50 27 8 •
40-250 65 40 100 470 170 170 180 225 65 15 4 28 125 95 45 320 250 160 110 340 M12 100 32 80 35 10
40-315 65 40 125 470 200 200 200 250 65 20 4 28 125 95 45 345 280 160 110 340 M12 100 32 80 35 10
50-160 80 50 100 360 130 130 160 180 50 15 4 28 100 70 45 265 212 160 110 260 M12 100 24 50 27 8
50-200 80 50 100 360 135 150 160 200 50 15 4 28 100 70 45 265 212 160 110 260 M12 100 24 50 27 8
50-250 80 50 125 470 170 170 180 225 65 15 4 28 125 95 45 320 250 160 110 340 M12 100 32 80 35 10
50-315 80 50 125 470 200 200 225 280 65 20 6 30 125 95 47 345 280 160 110 340 M12 100 32 80 35 10
65-160 100 65 100 360 130 155 160 200 65 15 4 28 125 95 45 280 212 160 110 260 M12 100 24 50 27 8
65-200 100 65 100 470 170 170 180 225 65 15 4 28 125 95 45 320 250 160 110 340 M12 140 32 80 35 10
65-250 100 65 125 470 170 190 200 250 80 18 4 28 160 120 45 360 280 160 110 340 M16 140 32 80 35 10
65-315 100 65 125 530 200 230 225 280 80 20 6 31 160 120 47 460 315 160 110 370 M16 140 42 110 45 12
80-160 125 80 125 360 145 180 180 225 65 15 4 28 125 95 45 320 250 160 110 260 M12 140 24 50 27 8
80-200 125 80 125 470 170 190 180 250 65 18 4 28 125 95 45 345 280 160 110 340 M12 140 32 80 35 10
80-250 125 80 125 470 185 210 225 280 80 18 6 30 160 120 47 400 315 160 110 340 M16 140 32 80 35 10
80-315 125 80 125 530 210 255 250 315 80 20 6 31 160 120 47 400 315 160 110 370 M16 140 42 110 45 12
80-400 125 80 125 530 245 260 280 355 80 20 6 31 160 120 47 435 355 160 110 370 M16 140 42 110 45 12
100-200 125 100 125 470 170 205 200 280 80 18 4 28 160 120 45 360 280 160 110 340 M16 140 32 80 35 10 •
100-250 125 100 140 530 200 230 225 280 80 20 6 31 160 120 47 400 315 160 110 370 M16 140 42 110 45 12
100-315 125 100 140 530 210 260 250 315 80 20 6 31 160 120 47 400 315 160 110 370 M16 140 42 110 45 12
100-400 125 100 140 530 250 295 280 355 100 20 6 31 200 150 47 500 400 160 110 370 M20 140 42 110 45 12 •
125-250 150 125 140 530 210 260 250 355 80 20 6 31 160 120 47 400 315 160 110 370 M16 140 42 110 45 12
125-315 150 125 140 530 215 255 280 355 100 20 6 31 200 150 47 500 400 160 110 370 M20 140 42 110 45 12 •
125-400 150 125 140 530 265 320 315 400 100 20 6 31 200 150 47 500 400 160 110 370 M20 140 42 110 45 12 •
150-250 200 150 160 530 225 285 280 375 100 20 6 31 200 150 47 500 400 160 110 370 M20 180 42 110 45 12
150-315 200 150 160 585 265 280 315 400 100 22 10 42 200 150 65 550 450 250 200 410 M20 180 60 105 64 18
150-400 200 150 160 585 300 330 315 450 100 22 10 42 200 150 65 550 450 250 200 410 M20 180 60 105 64 18
150-500 200 150 180 585 320 380 375 500 100 25 10 42 200 150 65 550 450 250 200 410 M20 180 60 105 64 18
200-250 200 200 180 530 265 340 355 425 100 27 6 31 200 150 47 550 450 160 110 370 M20 180 42 110 45 12
200-315 250 200 200 585 275 350 355 450 100 27 10 42 200 150 65 550 450 250 200 410 M20 180 60 105 64 18
200-400 250 200 180 585 315 370 355 500 100 30 10 42 200 150 65 550 450 250 200 410 M20 180 60 105 64 18
200-500 250 200 200 585 360 440 425 560 100 25 10 42 200 150 65 660 560 250 200 410 M20 180 60 105 64 18
250-315 300 250 250 585 315 445 400 560 130 30 10 42 260 190 65 690 560 250 200 410 M24 180 60 105 64 18

Dimensions in mm.

13
 CLT
MEDIUM-DUTY CENTRIFUGAL CHEMICAL PUMPS TO EN ISO 22858 (DIN 24256)

TOMBSTONE CURVES
100
1450 rpm
20
Pg. no.
80 15
0- 0-
5 Size*
50 00
0
60
80 10 12 15 20
- 40 0- 5- 0-
40 0- 25-160 3 42
0 40 400 0 40
40 0 0 25-200 4 43
40
-3
50
80 12 32-160 5 44
30 -3 65 10 5 15 20
15 15 -3 - 31 0- -3 0
15 5 31 15 -3 0-
31 25 32-200 6 45
5 15
50 5 0-
32 40 -2 65 31 32-250 7 46
-2 50 -2 80 5
20 -2 50 50 -2
50 50 12
20 40-160 8 47
15 0-
HEAD [m]

5 0 25
10 -2
50 -2
50
0 40-200 9 48
0-
32 40 50 250 40-250 10 49
25 -2 -2 -2 10
- 00 00 6
10
20
0
00 5- 80
-2 20 0- 40-315 11 50
20
25 32 0 00 0
-1 40 50-160 12 51
8 -1 60 -1 50
60 60
-1 65- 50-200 13 52
60 16 80
6 0 -1
60 50-250 14 53
50-315 15 54
4 65-160 16 55
65-200 17 56
3
65-250 18 57
65-315 19 58
2
3 4 6 8 10 20 30 40 60 80 100 200 300 400 600 800 1000 2000 80-160 20 59
FLOW RATE [m3/h]
80-200 21 60
80-250 22 61
160 80-315 23 62
2900 rpm
80-400 24
100-200 25 63
100-250 26 64
100
50 100-315 27 65
32 40 -2
-2 -2 50
80 50 50 65 80 100-400 28
-2 -2
50 50 125-250 29
10
0-
60 25
0
125-315 30
HEAD [m]

40 50
-2 10 125-400 31
-2 00 0-
00 20
25
65
-2 80 0 150-250 32
-2 32 00 -2
40 00 -2 00 150-315 33
00

50 150-400 34
32 40 -1 65
30 -1 60 -1
25
-1
60 60 60 150-500 35
-1
60 200-250 36
200-315 37
20 80 200-400 38
-1
60
200-500 39
250-315 40
250-400 41

10
2 3 4 6 8 10 20 30 40 60 3
80 100 200 300 400
FLOW RATE [m3/h]

* FOR INDIVIDUAL PUMP PERFORMANCE CURVES, REFER TO OUR CLT & CLB CURVES BOOK.

14
 CLB
MONOBLOCK CENTRIFUGAL CHEMICAL PUMPS TO EN ISO 22858 (DIN 24256)

APPLICATION
• Pharmaceutical
• Food and Beverage
• Air Conditioning
• Paints and Inks
• Steel Manufacturing
• Chemical Industry

RA Pump Minimum Maximum Minimum Maximum Maximum

Range Flow (m3/h) Flow (m3/h) Head (m) Head (m) Temperature

CLB 2 450 3 140 180˚C

DESIGN & CONSTRUCTION

• Closed couple single stage, end-suction and of shaft, therefore the pump runs off the motor
modular design with a high interchangeability of bearings and does not utilize its own bearing
parts. assembly.

• They are suitable for pumping clean liquids and • The volute casing is attached to the motor by
highly aggressive chemicals. means of a pump to motor bracket.

• Excellent hydraulic performance with low N.P.S.H • Offers a space saving option.
required values.
• More economical, cost saving.
• The suction flange is horizontal and the discharge is
vertical as standard however the volute may be
rotated on certain sizes. MATERIALS OF CONSTRUCTION
• Flanges conform to DIN 2543 PN16. Pump Shaft: Stainless Steel (316)
Volute Casing: 316 Stainless Steel*
• The wet end components of the pump (Volute, Impeller: Stainless Steel*
Impeller and Seal or Gland Plate) are supplied Shaft Sealing: Gland Packed or Mechanical
standard in high grade Cast Stainless Steel for Seal* to suit application
long life. Motor Bearings: Grease lubricated ball bearings

• They have overhung impellers, hydraulic balance is * Special alloys available to meet specific application.
effected by balance holes in the impeller. Standard
construction is with soft packed stuffing box or single, Motor
unbalanced mechanical seal. Standard I.E.C flange mounted or foot and flange
mounted three phase, 380 or 525 volt totally enclosed
• The entire range offers a high interchangeability, fan cooled motors are used, with either cast iron or
thus reducing spares stock holding. aluminum bodies. Non standard motors can be
supplied upon request.
• Stub shaft design which is attached onto the motor

15
 CLB
MONOBLOCK CENTRIFUGAL CHEMICAL PUMPS TO EN ISO 22858 (DIN 24256)

MODEL DESCRIPTION
CLB 50-160/5,5/2 S S M

Sealing Arrangement
Impeller Material
Volute Material
Motor speed 2 pole or 4 pole
Motor kW
Nominal Impeller diameter in mm
Discharge diameter in mm
Monoblock Design

SECTIONAL DRAWING
SINGLE-STAGE PUMP MECHANICAL SEAL
161.2 330
102 230 400.2 470.1 332
211

903

411 102.2

400.2

SINGLE UNBALANCED
MECHANICAL SEAL

940.1
230.1

920.1 220

GLAND PACKED
933
345
102 330
346 332 902 920.2

914.1
411

400.2
903

102.1
903 161.1 WITH LANTERN RING
& INTERNAL FLUSH
411
461

211

452

458 A A

16
 CLB
MONOBLOCK CENTRIFUGAL CHEMICAL PUMPS TO EN ISO 22858 (DIN 24256)

SECTIONAL DRAWINGS & PARTS LIST

PARTS LIST

DESCRIPTION PART NO. DESCRIPTION PART NO. DESCRIPTION PART NO.

VOLUTE CASING CLB (WITH FEET) 102.1 ADAPTOR PL ATE 348.1 PLUG 903
VOLUTE CASING CLB (WITHOUT FEET) 102.2 ADAPTOR PL ATE 348.2 SET SCREW 914.1
GL AND PL ATE 161.1 GASKET 400.2 SET SCREW 914.5
SEAL PL ATE 161.2 WASHER 4 11 COUNTERSUNK CAP SCREW 914.6
STUB SHAFT 25-160 220.1 GL AND 452 CAP SCREW 914.8
STUB SHAFT 360 & 470 220.2 L ANTERN RING 458 CAP SCREW 917.7
DRIVE COUPLING 223 GL AND PACKING RING 461 IMPELLER NUT - HEX 920.1
IMPELLER 230.1 MECHANICAL SEAL 470.1 NUT - HEX 920.2
BRACKET - PUMP/MOTOR (WITHOUT FOOT) 345 MOTOR 801 SPRING WASHER 933
BRACKET - PUMP/MOTOR (WITH FOOT) 346 STUD 902

POWER/MOTOR END

SHAFT SIZE 25-160 SHAFT SIZE 360 & 470

801

801 914.8
940.1 220.2 223
940.1 220.1 914.8

345 345
914.7
914.5 346
914.5

PUMP/MOTOR BRACKET MOTOR ADAPTOR PLATES

SIZE 25-160, 360/4, 360/11 & 470/22 FRAME D90S & D90L MOTORS

345 801
}
345
346
914.5

801

348.1

PUMP MOTOR FRAME D100L, D112M, D160M,

D160L, D180M - D180L MOTORS

161
914.5

400.2
345
346 }
102 914.6
904.1
801
914.5

348.2

17
 MONOBLOCK CENTRIFUGAL CHEMICAL PUMPS TO EN ISO 22858 (DIN 24256)

L x L x
b3 a b3 a
b1 b2 IDd b1 b2 IDd
A A bt
M1 M1
M2 M2
B B
s b p m2 m2 r s b p m2 m2 r
n2 m1 n2 m1
n1 n1
ARRANGEMENT TYPE: 3 ARRANGEMENT TYPE: 4
470/22F 530/1F/2F
CLB

L x
b3 a L x
b1 b2 IDd b3 a
b1 b2 IDd
M1 A
bt A
M1 bt
M2 M2
B
B
DIMENSIONS
s b p m2
s b p m2 r
n2 m1
n1 n2 m1
n1
ARRANGEMENT TYPE: 1 ARRANGEMENT TYPE: 2
360/4 360/IIF

18
 CLB
MONOBLOCK CENTRIFUGAL CHEMICAL PUMPS TO EN ISO 22858 (DIN 24256)

DIMENSIONS

Dismantling Space

Gauge Connection
Motor frame Size

Discharge Flange

Mass kg Approx.
Suction Flange

Drainage Hole
Arrangement

Prining Hole
Bracket

Motor
Pump

Bolts
Pole
CLB kW IDs IDd a b1 b2 ±b3 h1 h2 ±L b c m1 m2 r n1 n2 p S X A B M1/M2 Kg
25-160 25-160 1 0.55 D80 4 40 25 80 100 108 155 112 160 437 50 15 100 70 - 220 190 45 15 60 R1/4” R1/4” R1/4” 29
0.22 D90L 2

25-200 360/4 1 0.55 D80 4 40 25 80 132 132 145 160 180 509 50 15 100 70 - 240 190 45 15 80 R1/4” R1/4” R1/4” 33
0.75 35
1.1 D90S 522 38
2.2 D90L 2 165 594 47
3 D100L 190 611 54
32-160 360/4 1 0.55 D80 4 50 32 80 123 123 145 132 160 592 50 15 100 70 - 240 190 45 15 80 R1/4” R1/4” R1/4” 34
0.75 35
3 D100L 2 165 594 49
4 D112M 190 56
360/11 2 5.5 D132S 218 232 671 50 100 330 145 40 248 220 404 15 65
7.5 75
32-200 360/4 1 0.75 D80 4 50 32 80 124 130 145 160 180 494 50 15 100 70 - 240 190 45 15 80 R1/4” R1/4” R1/4” 40
1.1 155 522 44
360/4 1 3 100L 2 218 232 671 50 100 330 145 40 248 220 404 15
4 112M
360/11 2 5.5 D132S 70
7.5 80
32-250 470/22 3 7.5 132S 2 65 40 80 123 123 145 132 160 777 50 100 330 145 - 248 220 45 15 80 R1/4” R1/4” R1/4” 40
11 D160M
15 671
18.5 D160L 650
40-160 360/4 1 0.55 D80 4 65 40 80 123 123 145 132 160 494 50 15 100 70 - 240 190 45 15 80 R1/4” R1/4” R1/4” 40
0.75 D90S 155 42
1.1 D90L 547 4
360/4 2 3 100L 2 218 232 50 100 330 145 40 248 220 15 70
4 112M 80
360/11 5.5 132S 256 260 817 65 100 400 300 50 308 250 322 15 105
7.5
40-200 360/4 1 0.55 D80S 4 65 40 100 125 135 155 160 180 542 50 15 100 70 - 265 212 65 15 80 R1/4” R1/4” R1/4” 49
0.75 567 52
1.1 D90S 165 614 59
1.5 D90L
360/4 1 4 D112M 2 218 691 50 100 330 145 40 248 220 424 12 80
360/11 5.5 D132S 90
2 11 D160M 256 260 837 65 100 400 300 50 308 250 342 16 110
15 125
40-250 470/22 3 5.5 D132S 4 65 40 100 150 156 155 160 225 837 50 15 125 95 - 320 250 53 12 80 R1/4” R1/4” R1/4” 56
11 D160M 2 65
15 256 260 65 100 400 300 50 308 250 16 115
18.5 D160L 125
22 D180M 883 388 145
30 D200L
40-315 470/22 3 5.5 D132S 4 65 50 100 125 130 145 160 180 560 50 15 100 70 - 265 212 65 12 80 R1/4” R1/4” R1/4” 41
50-160 360/4 1 0.55 D80 4 80 50 100 125 130 145 160 180 560 50 15 100 70 - 265 212 45 14 80 R1/4” R1/4” R1/4” 41
0.75 625 45
1.1 D90S 48
1.5 D90L
360/4 1 4 D112M 2 218 232 691 50 100 330 145 40 248 220 424 12 70
5.5 D132S 80
360/11 2 7.5 D132S 256 260 837 65 400 300 50 308 250 342 16 105
11 D160M
15
50-200 360/4 1 1.1 D90S 4 65 50 100 133 145 155 160 200 567 50 15 100 70 - 265 212 65 15 80 R1/4” R1/4” R1/4” 59
1.5 D90L
2.2 D100L
3 49
360/4 1 7.5 D132S 2 218 232 691 50 100 330 145 40 248 220 424 12 95
11 D160M 260 400 300 50 308 250 115
360/11 2 15 256 65 130
18.5 D160L 145
50-250 470/22 3 5.5 D132S 4 65 50 100 156 169 165 180 225 616 65 15 125 95 - 320 250 53 12 80 R1/4” R1/4” R1/4” 69
470/22 3 15 D132S 2 218 260 839 65 100 400 300 50 308 250 344 16 130
18.5 D160L 150
22 D180M 276
80 80 450 350 349 279 215
30 D200L 1008 292 280 500 400 386 320 372 285
37 1008 305
50-315 470/22 3 5.5 D132S 4 65 50 100 156 169 165 180 225 1008 65 15 125 95 - 320 250 53 12 80 R1/4” R1/4” R1/4” 69
3 7.5 D132M 260 839 65 100 400 300 50 308 250 344 16 130
470/22 3 30 D200L 2 276 80 80 450 350 349 279 215
37 292 280 1008 500 400 386 320 372 285
45 D225SM
55 D250SM
65-160 360/4 1 0.55 D80 4 80 65 100 133 162 145 160 200 65 15 125 95 - 280 212 53 12 80 R1/4” R1/4” R1/4” 48
0.75 155 52
1.1 D90S 55
1.5 D90L 165 614 62
2.2 D100L 218 232 691 50 100 330 145 40 248 220 424 12 80
360/4 1 4 D90L 2 260 110
5.5 D132S
360/11 2 7.5
11 D160M
15 D160M

19
 CLB
MONOBLOCK CENTRIFUGAL CHEMICAL PUMPS TO EN ISO 22858 (DIN 24256)

DIMENSIONS

Dismantling Space

Gauge Connection
Motor frame Size

Discharge Flange

Mass kg Approx.
Suction Flange

Drainage Hole
Arrangement

Prining Hole
Bracket

Motor
Pump

Bolts
Pole
NB kW IDs IDd a b1 b2 ±b3 h1 h2 ±L b c m1 m2 r n1 n2 p S X A B M1/M2 Kg

65-200 470/22 3 11 D60M 2 80 65 100 148 170 155 180 225 567 65 15 155 95 - 320 250 53 12 80 R1/4” R1/4” R1/4” 58
15 165 65
18.5 D160L 256 260 837 65 100 400 300 50 308 250 342 16 115
22 D180M 130
30 D200L 145
65-250 470/22 3 5.5 D132S 4 80 65 100 164 184 218 232 250 730 50 100 330 145 40 248 220 463 12 100 R3/8” R3/8” R3/8” 125
7.5 D132M 768 16 135
11 D160M
22 D180M
30 D200L
37
45 D225SM
65-315 360/4 4 7.5 D132S 4 100 80 125 136 170 155 180 225 450 65 15 125 95 - 320 250 78 12 80 R1/4” R1/4” R1/4” 54
11 D160M
15 D160L
80-160 360/4 1 0.75 D80 4 100 80 125 136 170 155 180 225 450 65 15 125 95 - 320 250 78 12 80 R1/4” R1/4” R1/4” 54
1.1 D90S 57
1.5 165 567 64
2.2 D100L 592 67
3 639
360/4 1 7.5 D132M 2 218 232 716 50 100 330 145 40 248 220 449 12 90
11 D160M 256 260 862 65 400 300 50 308 250 367 16 115
360/11 15 D160M 125
18.5 D160L 906 411 145
22 D180M 276 928 80 80 450 350 349 279 363 210
80-200 470/22 3 5.5 D132S 4 100 80 125 163 188 218 232 250 755 50 100 330 145 40 248 220 488 12 100 R3/8” R3/8” R3/8” 125
470/22 3 18.5 D160L 2 256 945 65 400 300 50 308 250 450 210
22 D180M 276 967 80 80 450 350 349 279 402 245
30 D200L 292 280 1070 500 400 386 320 434 315
80-250 470/22F 2 5.5 D132S 4 100 80 125 182 208 218 232 280 755 50 100 330 145 40 248 220 488 12 100 R3/8” R3/8” R3/8” 135
7.5 D132M 793 145
11 D160M 256 901 65 400 300 50 308 250 406 16 165
30 D200L 2 180
37 945 450 200
45 D225SM 1264
55 D250SM 1300
75
80-315 470/22F 2 7.5 D132M 4 100 80 125 210 231 256 260 315 887 80 80 400 300 50 308 250 392 16 100 R3/8” R3/8” R3/8” 180
11 D160M 931 436 190
15 D160L 276 953 450 350 349 279 388 270
18.5
80-400 530/1F 4 11 D160M 4 125 100 140 256 272 256 360 919 78 200 520 210 50 490 420 373 16 185
15 D160L 205
18.5 D180M 276 985 180 570 235 520 450 361 225
22 D180L 1023 257
30 D200L 292 1110 160 600 250 560 490 391 325
100-200 470/22F 2 5.5 D132S 4 125 100 125 165 203 218 201 280 755 50 100 330 145 50 248 220 488 12 120 R3/8” R3/8” R3/8” 140
7.5 D132M 793 150
18.5 D160L 2 945 450 220
22 D180M 276 280 967 80 80 450 350 349 279 402 250
30 D200L 292 300 1070 500 400 386 320 434 320
37 340
45 D225S 366 370 1120 550 490 30 436 360 406 475
100/250 530/1F 2 11 D132M 4 125 100 140 189 224 218 232 280 808 50 100 330 145 50 248 220 503 12 120 R3/8” R3/8” R3/8” 145
15 D160M 256 260 946 65 400 300 308 250 421 16 175
18.5 160L 366 305 1135 18 80 550 490 30 436 360 475
37 D200L 349 350 1242 110 100 520 210 50 506 460 591 24 640
45 D225SM 1300 420 735
55 D250SM 1450
75
100/315 530/1F 2 11 D160M 4 125 100 140 220 250 256 260 315 946 65 100 400 300 50 308 250 451 16 120 R3/8” R3/8” R3/8” 205
15 276 968 80 80 450 350 349 279 390 280
18.5 D160L 1006 441 295
100-400 530/1F 4 18.5 D160L 4 125 100 140 256 272 276 360 355 1049 78 180 570 235 50 520 450 387 16 120 R3/8” R3/8” R3/8” 290
22 D180M 292 1136 160 600 250 560 490 417 16 350
30 D200L 366 360 1224 78 135 470 185 50 620 550 577 24 355
37 480
125-250 530/1F 4 11 D160M 4 150 125 140 212 255 256 260 355 916 65 100 400 300 50 386 320 421 16 120 R3/8” R3/8” R3/8” 190
15 960 465 205
18.5 D160L 276 982 80 80 450 350 349 279 417 280
125-315 530/1F 4 15 D160M 4 50 125 140 226 252 276 360 355 1011 78 180 570 235 50 520 450 387 16 120 R3/8” R3/8” R3/8” 290
18.5 D160L 1049 300
22 D180M 292 1136 160 600 250 560 490 417 375
30 D200L 366 360 1224 78 135 470 185 50 360 550 577 24 362
150-250 530/1F 4 11 D160M 4 200 150 160 231 283 256 360 375 1009 78 200 520 210 50 490 420 419 16 120 R3/8” R3/8” R3/8” 220
15 276 1031 180 570 235 520 450 407 295
18.5 D160L 1069 320
22 D180M 292 1156 160 600 250 560 490 437 385
30 D200L
37
150-315 530/1F 4 22 D180M 4 200 150 160 239 271 276 360 400 1069 78 180 570 235 50 520 450 407 16 120 R3/8” R3/8” R3/8” 320
30 D200L 292 1156 160 600 250 560 490 437 373
37 366 360 1244 78 135 470 185 50 620 550 597 24 375
45 D225SM 592
55 D250SM
150-400 530/2F 4 37 D225M 4 200 150 160 277 305 366 360 1244 78 135 470 185 50 620 550 597 24 120 395
45 600
55 D250M 349 1403 80 1010 52 210 690 620 604 694
75 520 865
90 280M 488 1435 80 600 250 730 660 646 1200
200-250 530/1F 4 22 D180L 4 200 200 180 262 330 276 360 425 1089 78 180 570 235 50 520 450 427 16 120 R3/8” R3/8” R3/8” 340
20 30 D200L 292 1176 160 600 250 560 490 457 392
530/2F 4 37 D225M 4 366 360 1264 78 135 470 185 50 620 550 617 24 384
 CLB
MONOBLOCK CENTRIFUGAL CHEMICAL PUMPS TO EN ISO 22858 (DIN 24256)

TOMBSTONE CURVES
100
1450 rpm
Pg. no.
80
Size*
60
80 10 12 15
-4 0- 5- 0- 25-160 3 42
00 40 40 40
0 0 0
40 25-200 4 43
40 50 32-160 5 44
-3 -3 80 10 12
30 15 65 -3 5- 15
15 -3 0- 31 0-
15 15 31 5 31 32-200 6 45
5 5
50
32 40 -2 65
80
32-250 7 46
20 -2 -2 50 -2
50 50 50 -2
50 40-160 8 47
HEAD [m]

12 15
5- 0-
10 25
0
25 40-200 9 48
0- 0
32 50 25
25 -2 40 -2 1 0 40-250 10 49
-2
-2
00
00 00 00 6
5- 80 20 00-
10 2 -2 0 40-315 11 50
32 00 00
25 -1 40
8 -1 60 -1 50
50-160 12 51
60 60
-1 65-
60 16 80 50-200 13 52
6 0 -1
60 50-250 14 53
50-315 15 54
4
65-160 16 55
3 65-200 17 56
65-250 18 57
2 65-315 19 58
3 4 6 8 10 20 30 40 60 80 100 200 300 400 600 800 1000 2000 80-160 20 59
FLOW RATE [m3/h]
80-200 21 60
80-250 22 61
160
2900 rpm
80-315 23 62
80-400 24
100-200 25 63

100
100-250 26 64
50 100-315 27 65
32 40 -2
-2 -2 50
80 50 50 65
-2 80 100-400 28
50 -2
50
10
125-250 29
60 0-
25
0 125-315 30
40 50 10 125-400 31
-2 -2 0-
00 00
HEAD [m]

65 20
25 -2 80 0 150-250 32
-2 32 00 -2
40 00 -2 00
00 150-315 33
50 65 150-400 34
32 40 -1 -1
30 -1 -1 60 60
25 60 60 150-500 35
-1
60
200-250 36
200-315 37
20 80
-1 200-400 38
60
200-500 39
250-315 40
250-400 41

10
2 3 4 6 8 10 20 30 40 60 3
80 100 200 300 400
FLOW RATE [m3/h]

* FOR INDIVIDUAL PUMP PERFORMANCE CURVES, REFER TO OUR CLT & CLB CURVES BOOK.
21
 Mariska Jolanda Free
Internal Sales
STRYKER MASCHINENBAU SYSTEME (PTY) LTD
Montenique Court Unit 23
42 Montrose Avenue, Randburg, 2162
Johannesburg, South Africa
VAT. nr: 4200319392
Phone: +27 69 297 3071 / +27 68 626 8490
[email protected]