Rajarambapu Institute Of Technology, Sakharale

DEPARTMENT OF MECHANICAL ENGINEERING [2011-2012] A SEMINAR REPORT ON

SOLAR WATER HEATING SYSTEM WITH PHASE CHANGE MATERIAL

SUBMITTED BY

Mr. Gaikwad Umesh Ashok

ROLL NO. 4850

ABSTRACT
The one of the most important part of a solar collector system is the solar tank. The solar collectors work daytime only, and its power depends on the weather. The hot water consumption in family houses is generally bigger in the evening and in the morning, so it is necessary to store the utilized energy. The collectors transform but not store the solar energy. The storage is necessary to accomplish in a heat-insulated tank, placed in tempered space. According the current architectural tendencies the boiler rooms are smaller, so the putting of the currently available solar tanks is very difficult. It is necessary to store the energy in a little space. The solution of the problem is the solar tank particularly filled with phase change material. This tank has smaller dimensions and bigger heat capacity than the conventional tanks. The other important advantage of a PCM solar tank is the possibility of the operating of the collectors at lower temperature. It could result a higher efficiency of the solar collector system. The storage system consists of two simultaneously functioning heat-absorbing units. One of them is a solar water heater and the other a heat storage unit consists of PCM. The solar water heater functions normally and supplies hot water during the day. The storage unit stores the heat in PCM.s during the day and supplies hot water during the night and overcast periods. The storage unit utilizes small cylinders made of filled with paraffin (PCM) as the heat storage medium and integrated with a solar collector to absorb solar energy. The performance of this PCM based thermal energy storage system is compared with conventional sensible heat storage system and the conclusions drawn from them are presented.

CONTENTS
1. Introduction 2. Phase change Materials 2.1 PCM in cooling & Heating 2.2 How it works 2.3 Applications 2.4 Advantages 3. Properties of PCM9 4. Classifications of PCM 4.1Organic phase change materials 4.1.1. Paraffins 4.1.2. Non-paraffins 4.2 Inorganic phase change materials 4.2.1. Salt hydrates. 4.2.2. Metallics 4.3 Eutectics. 5. Solar water heater with PCM 5.1 Solar Tanks13 6. Experimental set up14 7. Calculation of solidification 8. Experimental Result 9. Conclusion 10. References 15 16 19 20 11 11 11 11 11 12 13 10 10 6 7 7 7 8 8

1. INTRODUCTION
Energy is essential for the existence of human life and plays vital role in the progress of the nation. However the past few years have witnessed a rapid growth in global population putting a tremendous burden on energy resources .In the present scenario the importance of available energy cant be under Estimated. Also due to fast growth of the Indias economy. The countrys energy demand has grown to an average of 3.65% per annum over the past 30 years. So it has become a need to harness alternate and renewable energy sources. Today India has one of the highest potential for the effective use of renewable energy sources .The country has also invested heavily in recent years in renewable energy utilization. Solar energy being simple to use, clean, non polluting and inexhaustible has received wide spread attention in recent times. It provides well abundant energy source if utilized efficiently. But this energy is time dependent energy source with an intermittent character. Hence some form of thermal energy storage is necessary for more effective utilization of this energy source. Phase Change Material (PCM) is one of the techniques to store this thermal energy in the form of latent heat. Inorganic phase change materials (PCM) are hydrated salts that have large amount of heat energy stored in the form latent heat which is absorbed or released when materials changes state from liquid to solid or solid to liquid .The PCM retains its latent heat without any change in physical or chemical properties over thousands of cycles. This PCM has wide range of applications; one of them is in the solar water heater. One of the options is todevelop energy storage devices, which are as important as Developing new sources of energy.Energy storage not only reduces the mismatch between supplyand demand but also improves the performance and reliabilityof energy systems and plays an important role in conserving theenergy. It leads to saving of premium fuels and makes the system more cost effective by reducing the wastage of energyand capital cost.

2. PHASE CHANGE MATERIAL

These materials can store energy by the melting at a constant temperature. No material has all the optimal characteristics for a PCM, and the selection of a PCM for a given application requires careful consideration of the properties of various substances. Over 20,000 compounds and/or mixtures have been considered in PCM, including singlecomponentsystems, congruent mixtures, eutectics and peritectics. The isothermal operating characteristics (i.e. charging/discharging heat at a nearly constant temperature) during the solidification and melting processes, which is desirable forefficient operation of thermal systems. One of the most important aspects during the selecting of the material is the conformable melting point and the high latent heat of fusion. The choice of the substances used largely depends upon the temperature level of the application . Residential, commercial and industrial buildings often have hot water requirements at around 60 C and bathing, laundry and cleaning operations in the domestic sector generally need it at about 50 C [4]. The right melting point enables that the phase changing comes off during every usage cycle. Thereby the latent heat could be fullyutilized. According to the required temperature of the domestic hot water the meltingpoint should be between 40 and 50 C. Out of accordance with the conventional solar tanks the temperature of the accumulation of heat is constant. Storage systems using these heat accumulator materials can store the energy from the solar collector at lower temperature level, too in winter. The stored energy can be used for pre-heating the cold incoming water 2.1 PCMs in Cooling and Heating Based on the temperature requirement, a suitable PCM is selected. PCM quantity is determined by the time of back up required and the total heat being generated / required inthe system (external and internal) during the backup duration. PCM can be encapsulated in anyconvenient encapsulation and it can be reused multiple times.

2.2 How it works For human comfort or to increase the efficiency of a system, temperature maintenance is veryimportant. The ambient temperature of a place tends to increase due to the heat from the outside ordue to the heat produced in-house. To capture the excess heat some equipments like

chillers,refrigerated air, etc. are being used. This heat can also be captured by energy storage device. PCM isa good energy storage material, which absorbs such excess heat. This excess heats melts the PCM. This character of the PCM does not allow the temperature of the product to increase until the PCMmelts completely. Thus for a particular period of time (until the PCM melts completely) we canmaintain the temperature.Similarly when a heat source is being used for human comfort like solar water heater, a material likePCM that has high energy storage capacity (latent heat) than water (specific heat) can be used toincrease the storage capacity in the same volume.

2.3 Applications Energy saving in Telecommunication shelters while using natural energy Increasing life of Telecom equipment Reduce air-conditioning cost in building industry Increase hot water efficiency in solar water heaters Capture waste heat in boiler industry Cold storage/cold chain applications for horticulture Bio-Pharmaceuticals and vaccine transport Food / Poultry / Meat transport at specific temperatures Thermal wear for adverse climatic conditions Can be used as a room heater, same device / trolley can also be used as a cooler in summer Backup for room warmers / fireplace and so on

2.4 Advantages of PCMs Very High Latent Heat Can be tailor made for specific temperature requirements Easy handling and can be encapsulated in a variety of mediums Cheap and high stability over long periods of time Stable performance over repeated phase change cycles Limited / No supercooling Low / No flammability 6

 Non toxic Charge overnight & use during day as a cooler or charge in the daytime and use in the night time as a warmer. It comes longer than oil radiator heaters The room heaters can be switched off in the night time PCM can be used for 2 to 3 hrs PCM can be encapsulated in any form as per the customers requirement

3. PROPERTIES OF PCM Phase change materials (PCM) are Latent heat storagematerials. The thermal energy transfer occurs when a materialchanges from solid to liquid, or liquid to solid.

3.1. Thermal properties

(i) Suitable phase-transition temperature. (ii) High latent heat of transition. (iii) Good heat transfer.

Selecting a PCM for a particular application, the operatingtemperature of the heating or cooling should be matched to thetransition temperature of the PCM. The latent heat should be ashigh as possible, especially on a volumetric basis, to minimizethe physical size of the heat store. High thermal conductivitywould assist the charging and discharging of the energy storage.

3.2. Physical properties

(i) Favorable phase equilibrium. (ii) High density. (iii) Small volume change. (iv) Low vapor pressure. Phase stability during freezing melting would help towardssetting heat storage and high density is desirable to allow asmaller size of storage container. Small volume changes on phase transformation and small vapor pressure at operatingtemperatures to reduce the containment problem. 7

3.3. Chemical properties

(i) Long-term chemical stability. (ii) Compatibility with materials of construction. (iii) No toxicity. (iv) No fire hazard.

PCM can suffer from degradation by loss of water ofhydration, chemical decomposition or incompatibility withmaterials of construction. PCMs should be non-toxic, nonflammable and non-explosive for safety.

3.4. Economics

(i) Abundant. (ii) Available. (iii) Cost effective.

4. CLASSIFICATION OF PCM

Fig. 1 Classification of PCM (1)

4.1 Organic phase change materials Organic materials are further described as paraffin and nonparaffins.Organic materials include congruent melting meansmelt and freeze repeatedly without phase segregation and

consequent degradation of their latent heat of fusion, selfnucleation means they crystallize with little or no supercoolingand usually non-corrosiveness. 4.1.1. Paraffins

Paraffin is safe, reliable, predictable, less expensive and non-corrosive. The paraffins are waxes at room-temperature. These are hydrocarbons. Increasing thenumber of C-atoms increases the melting point too. The normal paraffins of typeCnH2n+2 are a family of saturated hydrocarbons with very similar properties. Paraffinsbetween C5 and C15 are liquids, and the rest are waxy solids. Paraffin wax is the mostcommonly used commercial organic heat storage PCM . Paraffin waxes are cheap and have moderate thermal energy storage density but low thermal conductivity and, hence, require large surface area

4.1.2. Non-paraffin The non-paraffin organic are the most numerous of the phasechange materials with highly varied properties. Each of thesematerials will have its own properties unlike the paraffins,which have very similar properties. This is the largest categoryof candidates materials for phase change storage. 4.2 Inorganic phase change materials 4.2.1 Salt hydrates Salt hydrates may be regarded as alloys of inorganic saltsand water forming a typical crystalline solid of general formulaAB_nH2O. The solidliquid transformation of salt hydrates isactually a dehydration of hydration of the salt, although thisprocess resembles melting or freezing thermodynamically.

4.2.2 Metallics This category includes the low melting metals and metaleutectics. These metallics have not yet been seriouslyconsidered for PCM technology because of weight penalties.

4.3 Eutectics A eutectic is a minimum-melting composition of two ormore components, each of which melts and freeze congruentlyforming a mixture of the component crystals during crystallization

5. Solar water heater with PCM

Now a days importance of solar water heater system has been increased, but many people are unaware of the new techniquesthat, these solar water heaters can be used at evening or in winter season.PCM can be used in solar water heater, to increase its efficiency based on the following principle. During day time, the raised hot water which absorbs the energy from the Sun will be stored in a tank.

Fig. 2 PCM in solar water heating system (5) When the tank is partially filled by PCM, the PCM will start to melt by absorbing the energy heat fromhot water. The PCM can also be wrapped over the tank by using a PCM jacket. Thus the PCMcan be charged during the day time. In the evening, in the absence of solar energy, theTemperature of the Hot water reduces by loss of heat to the environment. When the temperature goes below 580C, HS58 (type of PCM) will start to freeze. During its freezing, it will give up the heat to the water, and maintain the waters temperature at not less than 58 0C. This increases the efficiency of the solar water heater by allowing availability of hot water at nights.

10

5.1 Solar tanks The PCM tanks have two groups by the construction: PCM tanks with inner core, (fig. 3) PCM tanks with inner balls. (fig. 4)

The benefit of the tanks supplied with the inner core is the easy putting of the phase change material. The disadvantage of the inner core is the small surface. The phase change materials have small coefficient of thermal conductivity, so if the core has too big diameter the process of the melting and the solidification will be slow by the thicker and thicker solid layer on the inner surface of the core.

In the other type of the tanks the balls are filled with the phase change material. The diameter of the balls is very small for the diameter of the tank. The balls are not fixed tothe tank. It results a bigger heat exchange surface area between the water and the phase change material. The biggest disadvantage of this construction is the requirement special devices for making, filling and closing of the balls.

Fig. 3 Balls to encapsulate PCM (5)

Fig. 4 Arrangement of the tubes filled with

paraffin and the solar heat exchanger (2)

6. EXPERIMENTAL SET UP The schematic of the experimental set-up is shown in Figure 5. It consists of the cylindrical TES tank, which holds the tubes with PCM, solar flat plate collector, flow meter, temperature indicator and a circulating pump. The photographic view of the experimental set-up is shown 11

in Figure 5. The stainless steel TES tank has a capacity of 48 liters, capable of supplying water for a family of four, with an internal diameter of 360mm and a height of 460mm. The tank has 25 tubes filled with PCM with 60mm outer diameter. Tank contains two plenum chambers on the top and the bottom of the tank and a flow distributor is provided on the top of the tank to maintain a uniform flow. The tank is insulated with 50mm of glass wool and is provided with an aluminum cladding. It is considered that, on an average, the family would require 60 liters of heated water for their daily needs. This energy is stored as a mixture of sensible and latent heat of PCM, and sensible heat of water within the TES tank. We assume that the PCM store two-thirds of the energy while the remaining is stored as sensible heat of water. In the case of PCM less system, the same TES tank is used without having PCM shells.

Fig. 5.Experimental Set Up (5) 1. Solar flat plate collector; 2. Pump; 3 & 4.Flow control valves; 5. Flow meter; 6. TES tank; 7. PCM capsules; 8. Temperatureindicator; TP&Tf . Temperature sensors

12

Fig. 6 Photographic View of Experimental Set- up (5)

7. CALCULATION OF SOLIDIFICATION The main problem of the operating of the PCM tanks is the low coefficient of thermal Conductivityof the phase change material. During the discharging of the tank the PCM solidifies to the inner surface of the tube. The thermal flux will be decreased by thethermal insulating effect of the thicker and thicker solid PCM layer. I have calculatedthe required time of the solidification of the paraffin.The equation of the thermal conductivity in tubes with two layers (layer 1 is the solidphase of the paraffin, layer 2 is the wall of the tube)

PCM - coefficient of thermal conductivity of the paraffin w - coefficient of thermal conductivity of the tube d1 - inner diameter of the solid paraffin layer on the inner surface of the tube d2 - inner diameter of the tube

13

d3 - outer diameter of the tube tw1 - temperature of the phase change tw3 - temperature of the outer surface of the tube

During the solidification the value of d1 decreases from d2 to 0. The tw3-tw1 temperature difference depends on the temperature of the water in the tank. With the equation we can calculate the required time of the solidification.

The next diagram shows thedecrease of the r1=d1/2 inner radius of the solid phase in function of time. Theparameters are according to 60 mm tube diameter, 1 mm wall thickness, the PCM is paraffin, the material of the tube is stainless steel. The difference between the phasechange temperature and the temperature of the outer wall of the tube is 2 C

8. EXPERIMENTAL RESULTS
The lower difference between the temperature of the collector and the outer air results higher collector efficiency. The fig. 7 shows the irradiation and outer air temperature in a summer day.

14

Fig. 7 Irradiation, energy yield and air temperature in a typical summer day (2)

The paraffin has smaller specific heat capacity than the water, so it results higher temperature in the PCM-tank, than the conventional solar tank in a summer day:

15

Fig. 8 Comparing the temperature in a conventional solar tank and a PCM-tank with Paraffin (2) The fig.8 shows the result of a calculation of a PCM-tank with 70 kg water around the tubes and 170 kg paraffin in the tubes. We used for the calculation theefficiency characteristic of our own-designed experimental flat collectors.

The temperature of the PCM-tank is higher than the conventional because of the lower heat capacity of the PCM, so the collectors has to operate at higher temperature, and the efficiency is lower because of the heat loss from the collector to the air. If our goal is the higher efficiency we have to choose another PCM with lower melting point. The melting point of the Glaubers salt (Na2SO4 10H2O) is 32 C , and the latent heat is 250,9 kJ/(kgK). The heat capacity is 0,894 kJ/(kgK). The next figure shows the calculation for the same day with Glaubers salt:

16

Fig. 9 Comparing the temperature in a conventional solar tank and a PCM-tank with salt (2) System efficiency is defined as the ratio of the amount of energy stored by the tank to the heat energy available from the solar radiation.

Fig. 10Comparison of System Efficiency (5) It is observed from the fig10that the efficiency of the system without PCM is fluctuating over various periods of time, while the efficiency of the system with PCM is constant over the phase transition temperature and that it also shows a higher efficiency. Hence the system with PCM is more efficient.

17

9. CONCLUSION
The thermal behavior of the systems is investigated experimentally for various operating conditions. The effects of charging times, energy storage, time of solidification of PCM and efficiency of the systems are studied. These characteristics of both the systems are compared. At last it is concluded that : The cost of the manufacturing of the tank is lower than the conventional tanks in trade with the same heat capacity and the space demand is much lower too. The other advantage of the PCM tank is the constant temperature during the heat accumulation. This constant temperature could be lower, it depends on the type of the PCM. The lower temperature of the heat accumulation permits the higher efficiency of the collectors atlow external temperature. Hence thesystems with PCM are viable option for solar heat energy storage. Possessing considerableadvantages over the systems without PCM, it can be used as an alternative to current domestic sensible solar water heating technologies.

18

10. REFERENCES 1. Atul Sharma, V. V. Tyagi, C.R. Chen and D. Buddhi, Review on thermal energy storage with pase change materials & applications. 2. Istvan Peter Szabo, Design of an experimental phase change material solar tank.

3. Atul Sharma, Ashu Sharma, Nirdesh Pradhan and Biswarup Kumar, Performance evaluation of a solar water heater having built in lantent heat storage unit. 4. Phase change Material in heating and cooling applications. 5. C. V. Papade & N. M. Morkhane, Solar water heating system with phase change material.

19

20