ELECTRICAL CIRCUITS-2 (AC)

Lecture 2: Resonance (Part B)

1 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
 It is seen from the expression of the resonance
frequency that the resonance in a circuit can be
achieved by:

• At resonance I, VR
• When L=0, XL=0, VL=0 and VC are maximum.
• I, VR and VC are not zero.

• Lsr is value of inductance when resonance is occurred.

• Lm is value of inductance when voltage drop across
the inductor is maximum.
• VL is maximum after the resonance. When L=Lm,the
voltage across the inductor is maximum i.e. VL =VLmax.
• The value of Lm is obtained by setting:

2 Sadia Yasmin: [[email protected]]; Room # D0619

11/10/2022
• When C=0, XC=infinite, VC=supply voltage
• I, VR and VL are zero.

• At resonance I, VR and VL are maximum.

• Csr is value of Capacitance when resonance is occurred.

• Cm is value of capacitance when voltage drop across

the capacitor is maximum.
• VC is maximum before the resonance. It is assumed
that when C=Cm the voltage across the capacitor is
maximum i.e. VC =VCmax.
• The value of Cm is obtained by setting:

3 Sadia Yasmin: [[email protected]]; Room # D0619

11/10/2022
 • When f=0, XL =0, XC=infinite, VC=supply voltage and I, VR and VL are zero

• At resonance I, VR are maximum.

• VC are maximum before resonance.
• VL are maximum after resonance
• fvc is value of frequency when voltage drop across the capacitor is
maximum.
• fvl is value of frequency when voltage drop across the inductor is
maximum.
. The value of ωvl is obtained by setting:

. The value of ωvl is obtained by setting:

4 Sadia Yasmin: [[email protected]]; Room # D0619

11/10/2022
As inductor (L) is varied to produce resonance in a series circuit containing R=100 ohms, XC = 200 ohms, and
f=60 Hz, (i) find the value of inductance and the voltage drop across inductor (L) at resonance, and (ii) find the
voltage drop across the inductor (L) and the value of inductance when the drop across inductor (L) is a
maximum if 1000 V are impressed.

5 Sadia Yasmin: [[email protected]]; Room # D0619

11/10/2022
If the impressed voltage on a series circuit containing 100 ohms resistance, 100 ohms inductive reactance at 60
cycles, and a variable capacitance is 500 V, (i) find the value of capacitance and the voltage drop across
capacitor (C) at resonance, and (ii) find the voltage drop across the capacitor (C) and the value of capacitance
when the drop across capacitor (C) is maximum.

6 Sadia Yasmin: [[email protected]]; Room # D0619

11/10/2022
A series RLC circuit with resistance of 10 Ω, inductance of 0.1 H, and capacitance of 50 µF is supplied voltage
source of 50 V. Find resonant frequency and the frequencies at which maximum voltage appears across L and C.

Two impedances Z1 = 20 + j10 and Z2 = 10 - j30 are connected in parallel and this combination is connected in
series with Z3 = 30 + jX. Find whether inductor or capacitor is required which reactance is X to pass a specified
frequency.
Since Zp is capacitive, an
inductor is required to pass a
specified frequency. Now the
total impedance is given by:

For resonance, the imaginary part of total impedance should be zero that
means:
7
Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
8
Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
 Practical Parallel Resonance Circuit

Practical inductor and capacitor cannot behave as • RL presents the power loss in a practical inductor.
ideal inductor and capacitor because some power is • RC presents the power loss in a practical capacitor.
consumed by a practical inductor due to the wire of
coil and capacitor due to dielectric material.

9 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022

 Again,

and

10 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022

 Again,

11 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022

12 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
To make the supply voltage and current are in phase, the imaginary part of admittance must be zero that
means:

The frequency will be real if any one

of the following condition is
satisfied:

13 Sadia Yasmin: [[email protected]]; Room # D0619

14 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
15 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
16 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
17 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
 A parallel combination of inductor and capacitor can work as band
eliminator or rejector, suppressor or wave trap . A wave trap is connected
in series with antenna and receiver as shown in the following figure .

18 11/10/2022
19 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
20 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
21 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
Design the following circuit as shown in the following figure to
pass any wave of 45 kHz and block 15 kHz wave. Find the value
of L1 . By choosing the maximum inductance, what type of
reactance (inductive or capacitive) must be placed in series with
the source? Calculate the value of L0 or C0 which is required to
put.

To block 15 kHz wave, the parallel resonance

circuit is used. Thus at 15 kHz, To pass 45 kHz wave the series resonance circuit is used.
Thus at 45 kHz,

At resonance: 𝑩𝑳 = 𝑩𝑪

The parallel impedance is capacitive thus inductor (L0) is required.

For maximum inductance,
The dynamic impedance at 45 kHz will be:

22
 (Capacitor and Supply Voltage and Frequency are Fixed)

By considering the supply voltage V

as a reference, the vector of
capacitive branch IC (which is fixed)
can be drawn as following figure.

• Let, L=∞, then XL = ∞ (open-circuit), thus

• Let, L=0 then XL =0 (short-circuit), thus inductive branch current is zero that means:
inductive branch current is given by:

23
• If XL =RL then the current and angle • By changing the value of L and draw the vector of IL it look
of inductor branch current are: like as following Figure:

• By connecting the all end points of vectors of IL it will make a

semicircle which diameter is V/RL and radius is V/2RL . This
semicircle is called the locus (or path) of IL .

24 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022

• In order to draw the locus of total Three cases is possible here.
current I=IC+IL , first draw a parallel
line reference at the end point of IC
vector.

• Now just shift the locus of IL at the end

of IC vector. The new semicircle
represents the locus of I.

25
Inductor and Supply Voltage and Frequency are Fixed

26 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022

27 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
28 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
29 11/10/2022
30 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
31 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022
 REFERENCES

[1] Chapter V, Russell M Kerchner, George F Corcoran,

Alternating-Current Circuits, Fourth Edition

[2] PROFESSOR DR. ABDUL MANNAN SIR’S SLIDE

32 Sadia Yasmin: [[email protected]]; Room # D0619 11/10/2022