PISTON P UMPS FOR TRUCKS

FIXED DISPLACEMENT

VARIABLE DISPLACEMENT
2 Contents

XPi series

The DIN range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

XAi - SAE series

The SAE range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
FIXED Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DISPLACEMENT
PUMPS Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

PA - PAC series

The range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Performances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

TXV series

The range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Why use a variable displacement pump ? . . . . . . . . . . . . . . . . . . . 23
How does it work ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
VARIABLE Pressure-flow "Load Sensing" control . . . . . . . . . . . . . . . . . . . . . . 25
DISPLACEMENT Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
PUMPS Performances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
TXV 130 with through shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
TXVA - SAE series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
TXV with constant torque control . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Installation and start-up recommendations . . . . . . . 42
Shaft sealing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
The complete LEDUC product range . . . . . . . . . . . . . 46
 Piston pumps specially designed for truck hydraulics 3

XPi
▪ Models from 12 to 130 cc/rev

XPi series
▪ 380 bar continuous working pressure
▪ 420 bar peak pressure
▪ Automatic adjustment to desired direction of rotation
▪ For use on DIN-mount PTO

XAi - SAE
▪ Models from 18 to 63 cc/rev

XAi - SAE series

▪ SAE version of XPi bent axis piston pumps
▪ 380 bar continuous working pressure
▪ 420 bar peak pressure
▪ Automatic adjustment to desired direction of rotation
▪ For use on SAE-mount PTO

PA - PAC
▪ Single flow models from 25 to 114 cc/rev

PA - PAC series
▪ Twin flow models from 2x25 to 2x75 cc/rev
▪ Model with two different displacements
▪ 400 bar continuous working pressure
▪ 500 bar peak pressure
▪ Dual direction of rotation
▪ For use on DIN-mount PTO

TXV
▪ Variable displacement pumps with Load-Sensing control
▪ Displacement from 40 to 150 cc/rev
TXV series

▪ Maximum operating pressure up to 420 bar depending on model

▪ For use on DIN-mount PTO

▪ For use on SAE-mount PTO

TXVA - S A E ▪ Models available : 75 and 92 cc/rev

TXV
▪ Models from 40 to 150 cc/rev
w i t h Constant Torque ▪ TXV130 with constant torque control - with through shaft version
4 XPi - Presentation

XPi series
the intelligent pump
fixed displacement bent axis design

The compact size envelope of XPi pumps, together with their technology,
means they can be installed in environments with little space available,
and be used at relatively high rotating speeds .

A D VA N TA G E S

► Pump automatically sets to required direction of rotation

► Mounting and start-up, easier than ever !

CHARACTERISTICS
 7 pistons
 Innovative plate - barrel synchronisation
 use of materials with high mechanical resistance
 reinforced sealing

 10 models :
 from 12 to 130 cc/rev
 380 bar continuous working pressure
 420 bar peak pressure
 max . speed from 1750 to 3150 rpm
 Characteristics - XPi 5

Maximum Weight Overhang torque

Maximum Max. torque
intermittent peak
Pump Displac. continuous Max speed(1) absorbed at

XPi series
pressure without with without with
reference pressure 380 bar(2)
< 5 seconds inlet fitting inlet fitting 2ʺ inlet fitting inlet fitting 2ʺ
(cc/rev) (bar) (bar) (rpm) (N.m) (kg) (kg) (N.m) (N.m)
XPi 12 0523820 12 380 420 3150 76 9 .2 9 .65 8 .74 9 .17

XPi 18 0523810 18 380 420 2900 114 9 .25 9 .7 8 .79 9 .21

XPi 25 0523800 25 380 420 2750 159 9 .3 9 .75 8 .84 9 .26

XPi 32 0523790 32 380 420 2700 204 11 .1 11 .55 11 .1 11 .55

XPi 41 0523780 41 380 420 2550 261 11 .15 11 .6 11 .15 11 .6

XPi 50 0523770 50 .3 380 420 2450 318 11 .2 11 .65 11 .76 12 .23

XPi 63 0523760 63 380 420 2300 401 11 .25 11 .7 11 .81 12 .28

XPi 80 0523640 80 .4 380 420 2150 509 14 .85 15 .3 17 .82 18 .36

XPi 108 0523750 108 .3 380 420 1900 687 14 .95 15 .4 17 .94 18 .48

XPi 130 0523730 129 .8 380 420 1750 827 15 .35 15 .8 18 .73 19 .28

(1) At absolute pressure 1 bar, ISO VG46 fluid at 25°C.

(2) Maximum torque given with a mechanical efficiency at 95%.

Clockwise (CW) Counter-clockwise (CCW)

DUAL DIRECTION OF ROTATION:
this intelligent pump can operate
in either direction of rotation .
Fit the inlet fitting on required side, depending Inlet
on the direction of rotation of the PTO,
and the pump will set itself accordingly . Outlet

When the PTO turns When the PTO turns

counter-clockwise, the pump clockwise, the pump has to
has to turn clockwise. turn counter-clockwise.
6 XPi - Dimensions

+ 0.2
55 - 0.4 A F
Splined shaft: 8-32-36 80
7 E
DIN ISO 14 - NF 22.131 40
14.5
(DIN 5462)
M12x1.75-6H
25.95 ±0,1

40
Ø 80 - 0.013

80
40°
1.9 ±0.1 Ø 12.75 (4x)

C
37.9 +- 0.2
0.4

D
G3/8
"

B
G

VIEW G

Additionnal bore
H on the shaft
G on request. 18.2 ± 0.05

Ø 8,15 ± 0.05
Shaft bored
through

Pump reference A B C D E F G H

XPi 12 0523820 196 .7 177 .8 77 .1 103 .9 85 .7 108 G 3/4" 54

XPi 18 0523810 196 .7 177 .8 77 .1 103 .9 85 .7 108 G 3/4" 54
XPi 25 0523800 196 .7 177 .8 77 .1 103 .9 85 .7 108 G 3/4" 54
XPi 32 0523790 202 .8 184 82 .3 109 .1 85 .7 108 G 3/4" 54
XPi 41 0523780 202 .8 184 82 .3 109 .1 85 .7 108 G 3/4" 54
XPi 50 0523770 214 .4 195 .6 92 118 .9 85 .7 108 G 3/4" 54
XPi 63 0523760 214 .4 195 .6 92 118 .9 85 .7 108 G 3/4" 54
XPi 80 0523640 241 .7 220 .9 103 .5 133 .3 97 .4 123 G 1" 60
XPi 108 0523750 241 .7 222 .5 104 .8 133 .3 97 .4 123 G 1" 60
XPi 130 0523730 244 224 .8 106 .7 135 .2 97 .4 123 G 1" 60
Dimensions in mm .
 Performance - XPi 7

► Torque absorbed as a function of pump output pressure

(with a mechanical efficiency considered at 95%)
Torque (N.m)
900

XPi series
800 XPi 130

700 XPi 108 Cyl x ∆P

C=
XPi 80 62 .8 x ŋmeca
600
XPi 63 With:
500
XPi 50 C = Torque in N .m

400 Cyl = Displacement in cc/rev

XPi 41
∆P = Differential pressure in bar
XPi 32
300 ŋmeca = Mechanical efficiency
XPi 25
200
XPi 18
100
XPi 12

0
0 50 100 150 200 250 300 350 400 Pressure (bar)

► Flow as a function of rotating speed

Q (l/min)
250

XPi 130
Cyl x N x ŋvol
200 XPi 108 Q=
1000
XPi 80

XPi 63 With:
150
XPi 50 Q = Flow in l/min
XPi 41 N = Speed in rpm
100 XPi 32 ŋvol = Volumetric efficiency
XPi 25 Cyl = Displacement in cc/rev
XPi 18
50
XPi 12

0
0 500 1000 1500 2000 2500 3000 3500 4000 N (rpm)

These graphs are the results of testwork done in HYDRO LEDUC R&D laboratory, on a specific test bench
with a mineral hydraulic fluid ISO VG46 at 25°C (~100 cSt) - disregarding the volumetric efficiency.

► Volumetric efficiency
% Efficiency at 1000 rpm
100

90 Pressure
0 100 200 300 350 (bar)
8 XPi - Accessories

I N L ET F I T TIN GS F OR X Pi P U MPS
See recommendations of the hosing dimensions on page 40.
For high speeds, please consult .
All XPi pumps are supplied with their inlet fitting.
Please specify required fitting from the choice below when ordering.

4 5 ° elb o w fittin gs kit 9 0 ° e lb o w f it t in g s k it

xA

xA

E
E
F

Reference Ø hose ØA E F Reference Ø hose ØA E F

0519370 1 1/2" 39 .1 91 .7 46 .7 0521740 1 1/2" 39 .1 58 .6 79 .5
0519373 42 43 91 .7 46 .7 0521741 2" 51 .8 64 .9 80 .2
0519374 1 3/4" 46 91 .7 46 .7 0521742 2 1/2" 64 .5 71 .3 87 .5
0519371 2" 51 .8 108 .4 54 .4 Dimensions in mm .
0519372 2 1/2" 64 .5 125 .2 62 .2
Dimensions in mm .

DE FL E C TO R TO P R OT E C T S H A F T SEALS
This deflector ensures the protection of the pump shaft seals.
In particular, it protects the pump from projections of dirt from the road in cardan drive installations.

Reference: DEF 054111

BY-PA S S VA LV E F OR X Pi P U MP S

For XPi pump applications where the pump is driven by a continuous running PTO (PTO which cannot be disengaged), this solution allows
the continuous running of the pump:
▪ without creating problems of fluid overheating;
▪ without affecting pump service life;
▪ with no modifications necessary to the hydraulic circuit of the equipment.

 By-pass fitted on the back of the XPi pump.

Drain
Reference Pump Voltage Connector
BP63-0517931 XPi12 to XPi63 24 V HIRSCHMANN
BP63-P001835 XPi12 to XPi63 24 V DEUTSCH DT04-2P
BP80-0522140 XPi80 to XPi130 24 V HIRSCHMANN
BP80-P001840 XPi80 to XPi130 24 V DEUTSCH DT04-2P
By-pass valve
BP63-0521180 XPi12 to XPi63 12 V HIRSCHMANN
BP80-0522235 XPi80 to XPi130 12 V HIRSCHMANN
 Accessories - XPi 9

► How does it work ?

Application
The by-pass valve is a 24 Volts solenoid valve . M T
circuit
When not activated, it enables pump output to link up to pump inlet .

XPi series
When it is activated, the pump operates normally (output flow).

A drain line has to be installed between the By-Pass valve and the hydraulic tank of the vehicule to ensure sufficient oil circulation and a good
cooling into the pump . In any case, the connection to the tank must be done below the oil level .

► XPi overhang torque with by-pass

Weight Overhang torque

Pump
reference without with inlet without with inlet
inlet fitting fitting 2" inlet fitting fitting 2"
(kg) (kg) (N.m) (N.m)
XPi 12 12 .8 13 .25 16 .32 16 .90
XPi 18 12 .85 13 .3 16 .39 16 .96
XPi 25 12 .9 13 .35 16 .44 17 .02
XPi 32 14 .7 15 .15 18 .98 19 .56
XPi 41 14 .75 15 .2 19 .04 19 .62
XPi 50 14 .8 15 .25 20 .05 20 .67
XPi 63 14 .85 15 .3 20 .12 20 .73
XPi 80 18 .45 18 .9 27 .16 27 .82
XPi 108 18 .55 19 27 .31 27 .97
XPi 130 18 .95 19 .4 28 .16 28 .93

► Dimensions with by-pass valve

Pump reference A B C D E F G H J
XPi 12 / 18 / 25 289 .35 223 .04 202 .19 132 .20 114 .72 97 .58 3/4" 54 108
XPi 32 / 41 295 .5 229 208 .3 137 .3 120 .1 102 .7 3/4" 54 108
XPi 50 / 63 307 .1 240 .4 220 147 .1 129 .7 112 .5 3/4" 54 108
XPi 80 / 108 334 269 246 .7 157 .8 143 .9 124 .8 1" 60 123
XPi 130 336 .3 271 .3 249 159 .7 145 .8 126 .7 1" 60 123 .5
Dimensions in mm .

A
B
C

Drain G 1/4'' (T)

to be connected to the tank
D
E
F

G
H
118
J
10 XAi SAE version - Presentation

XAi series
the intelligent pump - SAE version
fixed displacement bent axis design

The compact size envelope of XAi pumps, together with their technology, means
they can be installed in environments with little space available,
and be used at relatively high rotating speeds .

A D VA N TA G E S

► Pump automatically sets to required direction of rotation

► Mounting and start-up, easier than ever !

CHARACTERISTICS
 10 models :
 7 pistons
 from 18 to 63 cc/rev (1.1 to 3.84 cu.in/rev)
 original idea for plate - barrel synchronisation
 380 bar (5511 psi) continuous working pressure
 use of materials with high mechanical resistance
 420 bar (6092 psi) peak pressure
 reinforced sealing
 maximum speed from 2300 to 2650 rpm

4 bolt
flange models
2 bolt
flange models
 Characteristics - XAi SAE version 11

► 2 bolt flange - SAE J744

Maximum Max. torque Weight Overhang torque
Maximum
Pump peak absorbed at
Displac. continuous Max speed(1)
reference pressure 5511 psi without with inlet without with inlet
pressure
< 5 seconds (380 bar)(2) inlet fitting fitting 2" inlet fitting fitting 2"
Cu.in/rev
psi (bar) psi (bar) rpm lbf ft (N.m) lbs (kg) lbs (kg) lbf ft (N.m) lbf ft (N.m)
(cc/rev)
XAi 18 0524085 1 .1 (18) 5511 (380) 6092 (420) 2400 84 (114) 22 .15 (10 .5) 23 .14 (10 .5) 7 .04 (9 .54) 7 .35 (9 .97)

XAi 25 0524095 1 .52 (25) 5511 (380) 6092 (420) 2650 117 (159) 22 .38 (10 .15) 23 .36 (10 .6) 7 .11 (9 .64) 7 .43 (10 .07)

XAi 32 0524105 1 .95 (32) 5511 (380) 6092 (420) 2600 150 (204) 26 .34 (11 .95) 27 .67 (12 .4) 8 .81 (11 .95) 9 .15 (12 .4)

XAi 41 0524115 2 .5 (41) 5511 (380) 6092 (420) 2550 192 (261) 26 .45 (12) 27 .45 (12 .45) 8 .85 (12) 9 .18 (12 .45)

(1) At absolute pressure 14,50 psi (1 bar), ISO VG46 fluid at 25°C.
(2) Maximum torque given with a mechanical efficiency at 95%.

► 4 bolt flange - SAE J744

XAi - SAE series

Maximum Max. torque Weight Overhang torque
Maximum
Pump peak (1) absorbed at
Displac. continuous Max speed
reference pressure 5511 psi without with inlet without with inlet
pressure
< 5 seconds (380 bar)(2) inlet fitting fitting inlet fitting fitting
Cu.in/rev
psi (bar) psi (bar) rpm lbf ft (N.m) lbs (kg) lbs (kg) lbf ft (N.m) lbf ft (N.m)
(cc/rev)
XAi 18 0524080 1 .1 (18) 5511 (380) 6092 (420) 2400 84 (114) 22 .59 (10 .25) 23 .59 (10 .7) 7 .18 (9 .73) 7 .49 (10 .16)

XAi 25 0524090 1 .52 (25) 5511 (380) 6092 (420) 2650 117 (159) 22 .71 (10 .3) 23 .70 (10 .75) 7 .19 (9 .75) 7 .53 (10 .21)

XAi 32 0524100 1 .95 (32) 5511 (380) 6092 (420) 2600 150 (204) 26 .68 (12 .1) 27 .67 (12 .55) 8 .92 (12 .1) 9 .26 (12 .55)

XAi 41 0524110 2 .5 (41) 5511 (380) 6092 (420) 2550 192 (261) 26 .78 (12 .15) 27 .78 (12 .6) 8 .96 (12 .15) 9 .29 (12 .6)
XAi 50 0524360 3 .07 (50 .3) 5511 (380) 6092 (420) 2450 234 (318) 26 .89 (12 .2) 27 .89 (12 .65) 9 .45 (12 .81) 9 .80 (13 .28)
XAi 50 0524365
XAi 63 0524125 3 .84 (63) 5511 (380) 6092 (420) 2300 295 (401) 27 .01 (12 .25) 28 (12 .7) 9 .49 (12 .86) 9 .83 (13 .33)

(1) At absolute pressure 14,50 psi (1 bar), ISO VG46 fluid at 25°C.
(2) Maximum torque given with a mechanical efficiency at 95%.

DUAL DIRECTION OF ROTATION:

this intelligent pump can operate
Clockwise (CW) Counter-clockwise (CCW)
in either direction of rotation .
Fit the inlet fitting on required side, depending
on the direction of rotation of the PTO,
and the pump will set itself accordingly .
Inlet

Outlet

When the PTO turns When the PTO turns

counter-clockwise, the pump clockwise, the pump has to
has to turn clockwise. turn counter-clockwise.
12 XAi SAE version - Dimensions

1.62 (41.3) A
4.67 (118.5) 6.85 (174)
0.38 (9.65)
3.53 (89.8) 5.75 (146)
Splined shaft SAE B 7/8" 0.63 (16)
13T 16/32DP

M8x1.25-6H M8 x 1.25-6H
0.0008 (Ø101.6)

4.67 (118.5)
3.53 (89.8)
4.00 -0.0000

2x Ø 0.56
40°

( 14.3)
0.79 (20)
D 4x Ø 0.56
C ( 14.3)
1.31 ±0.01 (33.3)
0.31 (7.9)
9/16
"-18
UNF
-2B

B
4.27 (108.5) 4.27 (108.5)
1.81 (46) A
Splined shaft SAE BB 1" 0.38 (9.65)
15T 16/32DP SAE B 4 bolts (SAE J744) SAE B 2 bolts (SAE J744)
2.1
F 3(
54
0.0008 (Ø101.6)

)
4.00 -0.0000

1.08 (27.5)

F
1.50 ±0.01 (38.1)
0.31 (7.9) View from A

► SAE B - 2 bolt mounting configurations (SAE J744)

Pump type A B C D F Shaft

XAi 18 0524085 7 .76 (197 .2) 6 .79 (172 .5) 4 .08 (103 .7) 2 .87 (73) 1 1/16"-12 UNF-2B SAE B 7/8" 13T-16/32DP

XAi 25 0524095 7 .76 (197 .2) 6 .79 (172 .5) 4 .08 (103 .7) 2 .87 (73) 1 1/16"-12 UNF-2B SAE B 7/8" 13T-16/32DP

XAi 32 0524105 8 (203 .2) 7 .03 (178 .5) 4 .28 (108 .7) 3 .03 (77) 1 1/16"-12 UNF-2B SAE B 7/8" 13T-16/32DP

XAi 41 0524115 8 (203 .2) 7 .03 (178 .5) 4 .28 (108 .7) 3 .03 (77) 1 1/16"-12 UNF-2B SAE B 7/8" 13T-16/32DP

► SAE B - 4 bolt mounting configurations (SAE J744)

Pump type A B C D F Shaft

XAi 18 0524080 7 .76 (197 .2) 6 .79 (172 .5) 4 .08 (103 .7) 2 .87 (73) 1 1/16"-12 UNF-2B SAE B 7/8" 13T-16/32DP

XAi 25 0524090 7 .76 (197 .2) 6 .79 (172 .5) 4 .08 (103 .7) 2 .87 (73) 1 1/16"-12 UNF-2B SAE B 7/8" 13T-16/32DP

XAi 32 0524100 8 (203 .2) 7 .02 (178 .5) 4 .28 (108 .7) 3 .03 (77) 1 1/16"-12 UNF-2B SAE B 7/8" 13T-16/32DP

XAi 41 0524110 8 (203 .2) 7 .02 (178 .5) 4 .28 (108 .7) 3 .03 (77) 1 1/16"-12 UNF-2B SAE B 7/8" 13T-16/32DP

XAi 50 0524360 8 .45 (214 .7) 7 .48 (190) 4 .65 (118 .2) 3 .4 (86 .5) 1 1/16"-12 UNF-2B SAE B 7/8" 13T-16/32DP

XAi 50 0524365 8 .45 (214 .7) 7 .48 (190) 4 .65 (118 .2) 3 .4 (86 .5) 1 1/16"-12 UNF-2B SAE BB 1" 15T-16/32DP

XAi 63 0524125 8 .45 (214 .7) 7 .48 (190) 4 .65 (118 .2) 3 .4 (86 .5) 1 1/16"-12 UNF-2B SAE BB 1" 15T-16/32DP

Dimensions in inches (mm) .

 Performance - XAi SAE version 13

► Torque absorbed as a function of pump output pressure

(with a mechanical efficiency considered at 95%)
Torque (lbf ft)

350 Cyl x ∆P
C=
62 .8 x ŋmeca
300 XAi 63
With:
XAi 50
250 C = Torque in N .m
XAi 41 Cyl = Displacement in cc/rev
200
∆P = Differential pressure in bar
XAi 32
150 ŋmeca = Mechanical efficiency
XAi 25
100
XAi 18

50

XAi - SAE series

0
0 1000 2000 3000 4000 5000 6000 Pressure (psi)

► Flow as a function of rotating speed

Q (gallons/min)
40
XAi 63 Cyl x N x ŋvol
Q=
35 1000
XAi 50
30 With:
XAi 41 Q = Flow in l/min
25
N = Speed in rpm
XAi 32
20 ŋvol = Volumetric efficiency
XAi 25 Cyl = Displacement in cc/rev
15

10 XAi 18

0
0 500 1000 1500 2000 2500 3000 3500 N (rpm)

These graphs are the results of testwork done in HYDRO LEDUC R&D laboratory, on a specific test bench
with a mineral hydraulic fluid ISO VG46 at 25°C (~100 cSt) - disregarding the volumetric efficiency.

► Volumetric efficiency
% Efficiency at 1000 rpm
100

90 Pressure
0 100 200 300 350 (bar)
14 XAi SAE version - Accessories

I NL ET F I T T I N GS F OR X Ai P U MP S
See recommendations of the hosing dimensions on page 40.
For high speeds, please consult .
All XAi pumps are supplied with their inlet fitting.
Please specify required fitting from the choice below when ordering.

4 5 ° e lb o w fittin gs kit 9 0 ° e lb o w f it t in g s k it

xA

xA

E
E
F

Reference Ø hose ØA E F Reference Ø hose ØA E F

0519370 1 1/2" 39 .1 91 .7 46 .7 0521740 1 1/2" 39 .1 58 .6 79 .5
0519373 42 43 91 .7 46 .7 0521741 2" 51 .8 64 .9 80 .2
0519374 1 3/4" 46 91 .7 46 .7 0521742 2 1/2" 64 .5 71 .3 87 .5
0519371 2" 51 .8 108 .4 54 .4 Dimensions in mm .
0519372 2 1/2" 64 .5 125 .2 62 .2
Dimensions in mm .

BY-PA S S VA LV E F OR X A i P U MP S

For XAi pump applications where the pump is driven by a continuous running PTO (PTO which cannot be disengaged), this solution allows
the continuous running of the pump:
▪ without creating problems of fluid overheating;
▪ without affecting pump service life;
▪ with no modifications necessary to the hydraulic circuit of the equipment.
Drain

 By-pass fitted on the back of the XAi pump.

Part number Pump Voltage Connector

BPA63-0521715 XAi 18 to XAi 63 24 V HIRSCHMANN

By-pass valve

► How does it work ?

Application
The by-pass valve is a solenoid valve (12 or 24 Volts) . M T
circuit
When not activated, it enables pump output to link up to pump inlet .
When it is activated, the pump operates normally (output flow).

A drain line has to be installed between the By-Pass valve and the hydraulic tank of the vehicule to ensure sufficient oil circulation
and a good cooling into the pump . In any case, the connection to the tank must be done below the oil level .
 Accessories - XAi SAE version 15

► XA i overhang torque with by-pass

2 b o lt fl an g e - S A E J744
Weight Overhang torque
Pump
reference without with without with
inlet fitting inlet fitting 2" inlet fitting inlet fitting 2"
lbs (kg) lbs (kg) lbf ft (N.m) llbf ft (N.m)
XAi 18 - 2 bolts 28 .33 (12 .85) 29 .32 (13 .30) 9 .87 (13 .38) 12 .51 (16 .96)
XAi 25 - 2 bolts 28 .44 (12 .90) 29 .43 (13 .35) 12 .13 (16 .45) 12 .55 (17 .02)
XAi 32 - 2 bolts 32 .41 (14 .70) 33 .40 (15 .15) 14 (18 .98) 14 .43 (19 .56)
XAi 41 - 2 bolts 32 .52 (14 .75) 33 .51 (15 .20) 10 .36 (14 .04) 14 .47 (19 .62)

4 b o lt fl an g e - S A E J744

XAi - SAE series

Weight Overhang torque
Pump
reference without with without with
inlet fitting inlet fitting 2" inlet fitting inlet fitting 2"
lbs (kg) lbs (kg) lbf ft (N.m) lbf ft (N.m)
XAi 18 - 4 bolts 28 .77 (13 .05) 29 .76 (13 .50) 12 .27 (16 .64) 12 .69 (17 .21)
XAi 25 - 4 bolts 28 .77 (13 .05) 29 .76 (13 .50) 12 .27 (16 .64) 12 .69 (17 .21)
XAi 32 - 4 bolts 32 .74 (14 .85) 33 .73 (15 .30) 14 .14 (19 .17) 14 .57 (19 .75)
XAi 41 - 4 bolts 32 .85 (14 .90) 33 .84 (15 .35) 14 .19 (19 .24) 14 .62 (19 .82)
XAi 50 - 4 bolts 32 .63 (14 .80) 33 .62 (15 .25) 14 .79 (20 .05) 15 .24 (20 .66)
XAi 63 - 4 bolts 32 .74 (14 .85) 33 .73 (15 .30) 14 .84 (20 .12) 15 .29 (20 .73)

► Dimensions with by-pass valve

Pump reference A B C D E F G H J
XAi 18 / 25 11 .43 (290 .4) 8 .81 (223 .9) 8 .00 (203 .2) 5 .20 (132 .1) 4 .53 (115) 3 .84 (97 .6) 1 1/16"- 16UNF - 2B 2 .13 (54) 4 .25 (108)
XAi 32 / 41 11 .67 (296 .5) 9 .06 (230) 8 .24 (209 .2) 5 .41 (137 .3) 4 .73 (120 .1) 4 .04 (102 .7) 1 1/16"- 16UNF - 2B 2 .13 (54) 4 .25 (108)
XAi 50 / 63 12 .13 (308 .2) 9 .52 (241 .7) 8 .70 (221) 5 .79 (147) 5 .11 (129 .9) 4 .43 (112 .5) 1 1/16"- 16UNF - 2B 2 .13 (54) 4 .25 (108)

A
D

Drain G1/4" (T)

E
F

C
H B
J
4.65 (118)

Dimensions in inches (mm) .

16 PA | PA C - P r e s e n t a t i o n

PA | PAC series
piston pumps
fixed displacement in-line design

A D VA N TA G E S

► Of unique design, the PA and PAC pumps offer a robust solution with long service life for high
pressure requirements in truck hydraulics.

► Relatively insensitive to contamination, these pumps are particularly well suited to

the harshest environments.

► The design means the pumps can rotate either clockwise or counter-clockwise
without any user intervention.

► Like all truck pumps designed by HYDRO LEDUC, this range is fitted with the
latest innovation in terms of sealing:

 Front of pump fitted with two shaft seals: externally, a seal capable of resisting the high temperatures
of the gearbox, and internally, a seal adapted to the hydraulic requirements.

 A transparent flexible tube fitted between the two seals, to protect these seals from dirt from the road,
and from high pressure water jet during washing of vehicle etc...
 C h a r a c t e r i s t i c s - PA | PA C 17

The PA, PAC pump series comprises two ranges, all designed for truck
applications at working pressures up to 5800 psi (400 bar) continuous and
7252 psi (500 bar) peak.

PA - PAC
Series
 PA pumps
ƒ single flow from 25 to 114 cc/rev
ƒ twin-flow from 2x50 to 2x75 cc/rev
ƒ two different flows: 75-40 cc/rev
 PA C pumps
Series offering the most compact size envelope :
ƒ single flow from 40 to 80 cc/rev
ƒ twin-flow from 2x25 to 2x40 cc/rev
18 PA | PA C - D i m e n s i o n s

55 A
G
B C

Splined shaft: 8-32-36

DIN ISO 14 - NF 22.131 12
(DIN 5462) 9

M12x1,75-6H

E
D

80
F
D
80
J (Inlet) K (Outlet) 98

Displacement Max. torque

Overhang
(cc/rev) Weight Max. speed absorbed
Pump reference A B C D E F G J K torque
(kg) (rpm) at 400 bar (1)
(N.m)
(N.m)

► S i n gle flow
PA 25 0511510 25 - 261 102 126 47 78 64 107 G 1 1/2" G 3/4" 15 17 2200 177
PA 32 0511515 34 - 261 102 126 47 78 64 107 G 1 1/2" G 3/4" 15 17 2000 240
PA 40 0511520 43 - 261 102 126 47 78 64 107 G 1 1/2" G 3/4" 15 17 1750 304
PA 50 0511525 50 - 261 102 126 47 78 64 107 G 1 1/2" G 3/4" 15 17 1650 354
PA 100 0511565 104 - 290 123 138 .8 69 90 69 124 G 2" G 3/4" 23 .5 31 .5 1400 736
PA 114 0511570 114 - 290 123 138 .8 69 90 69 124 G 2" G 3/4" 23 .5 31 .5 1350 807

PAC 40 0511460 40 - 226 94 .9 103 .3 62 73 .2 54 98 G 1 1/2" G 3/4" 12 .5 12 .6 1800 283

PAC 50 0511465 50 - 226 94 .9 103 .3 62 73 .2 54 98 G 1 1/2" G 3/4" 12 .5 12 .6 1650 354
PAC 65 0511490 65 - 243 102 .5 112 .8 63 78 65 107 G 1 1/2" G 3/4" 16 17 .6 1500 460
PAC 80 0511705 78 - 247 102 .5 116 .3 63 78 65 107 G 1 1/2" G 3/4" 17 21 .3 1350 552

► Twin-flow - 2 x 3 pi st ons
PA 2 x 50 0511555 52 52 290 123 138 .8 69 90 69 124 G 2" G 3/4" 23 .5 31 .5 1400 736(2)
PA 2 x 57 0511560 57 57 290 123 138 .8 69 90 69 124 G 2" G 3/4" 23 .5 31 .5 1350 807(2)
PA 2 x 75 0516100 75 75 302 126 147 .8 72 .5 90 72 .5 135 G 2" G 3/4" 26 .8 38 .7 1350 1062(2)

PA 75-40 0516810 75 40 302 126 147 .8 72 .5 90 72 .5 135 G 2" G 3/4" 27 .4 38 .7 1350 807(2)

PAC 2 x 25 0511480 25 25 243 102 .5 112 .8 63 78 65 107 G 1 1/2" G 3/4" 16 17 .6 1750 354(2)
PAC 2 x 32 0511485 32 32 243 102 .5 112 .8 63 78 65 107 G 1 1/2" G 3/4" 16 17 .6 1500 460(2)
PAC 2 x 40 0511710 39 39 247 102 .5 116 .3 63 78 65 107 G 1 1/2" G 3/4" 17 21 .3 1350 552(2)

(1) Maximum torque given with a mechanical efficiency at 90%.

(2) Maximum torque for the two pressure ports at 400 bar .

Dimensions in mm .
 P e r f o r m a n c e - PA | PA C 19

► Torque absorbed as a function of pump output pressure

(with a mechanical efficiency considered at 90%)

S i n gle flo w m odels

PA s e r i e s PA C s e r i e s
Single flow models PA Single flow models PAC
600
900
800 500 PAC 80
PA114
700 PAC 65
PA100 400

Torque (Nm)
600 PAC 50
Torque (Nm)

500 PA50 300 PAC 40

400 PA40 200
300 PA32
100
200 PA25
100 0
0 50 100 150 200 250 300 350 400 450
0
0 50 100 150 200 250 300 350 400 450 Pressure (bar)
Pressure (bar)

Tw i n - fl ow m od els
PA s e r i e s PA C s e r i e s
Twin flow models PA Twin flow models PAC
1200
600
1000
PA 2x75

PA - PAC
500
Torque (Nm)

Series
800 PA 75-40
400
Torque (Nm)

600 PA 2x57
PA 2x50 300 PAC2x40
400
PAC2x32
200 200
PAC2x25
0 100
0 50 100 150 200 250 300 350 400 450
Pressure (bar) 0
0 50 100 150 200 250 300 350 400 450
Pressure (bar)

► Calculation of power to be supplied to the shaft as a function of flow and pressure

P = Hydraulic power in kW
∆P x Q
P= Q = Flow in l/min
600 x ŋglobal
ŋglobal = Volumetric efficiency + mechanical efficiency
Ca lc u la tio n of t or que t o det er m i ne P TO ,
a s a fu n c tio n o f t he di s pl ac em ent and t he pr es su r e C = Torque in N .m
Cyl = Displacement in cc/rev
Cyl x ∆P
C = 62 .8 x ŋ ∆P = Differential pressure at the pump terminals, in bar
meca
ŋmeca = Mechanical efficiency
20 PA | PA C - P e r f o r m a n c e

► Flow as a function of rotating speed

S i n gle flo w m odels

PA s e r i e s PA C s e r i e s
Single flow models PA Single flow models PAC
180 120
160 PA 114 PAC 80
100
140 PA 100 PAC 65
120 80 PAC 50
PA 50

Q (l/min)
Q (l/min)

100
PA 40 60 PAC 40
80
60 PA 32 40
40 PA 25
20
20
0 0
0 500 1000 1500 2000 0 500 1000 1500 2000 2500
N (rpm) N (rpm)

Tw i n - fl ow m od els
PA s e r i e s PA C s e r i e s
Twin flow models PA Twin flow models PAC
250 120

200 100

150 80
PAC 2x40
Q (l/min)

Q (l/min)

PA2x75
60 PAC 2x32
100 PA75-40
PA2x57 40 PAC 2x25
50 PA2x50
20
0
0 500 1000 1500 2000 0
0 500 1000 1500 2000
N (rpm)
N (rpm)

► Calculation of the flow

Cyl x N x ŋvol
Q=
1000
Avec :
Q = Flow in l/min
Cyl = Displacement in cc/rev
N = Speed in rpm
ŋvol = Volumetric efficiency

► Volumetric efficiency
These graphs are the results of testwork done in HYDRO LEDUC
% Efficiency at 1000 rpm
R&D laboratory, on a specific test bench with a mineral hydraulic 100
fluid ISO VG46 at 25°C (~100 cSt) - disregarding the volumetric
efficiency.

90 Pressure
0 100 200 300 350 (bar)
 A c c e s s o r i e s - PA | PA C 21

I NLET F I T T I N GS F OR PA | PA C P UMPS
See recommendations of the hosing dimensions on page 40.
For high speeds, please consult .

9 0 ° elb o w fittin gs, swivel F

Reference A ØB C D E F

ØB
240131 G 1 1/2" 40 60 17 61 77
E
240133 G 1 1/2" 50 60 17 65 82
C
D
240135 G 2" 50 70 17 65 82
ØA
Dimensions in mm .

S t r a i g h t fi tti ng s
Reference A ØB C D E
ØB

240182 G 1 1/2" 40 55 16 52

240067 G 1 1/2" 48 55 16 64 E

240066 G 1 1/2" 60 65 16 67 D C

ØA
240186 G 1 1/2" 63 .5 65 16 67

240183 G 2" 50 65 16 52

PA - PAC
Series
240170 G 2" 60 65 16 70

240201 G 1 1/2" 76 .2 80 16 87

Dimensions in mm .

DEF L E C TO R TO P R OT E C T S H A F T SEALS
This deflector ensures the protection of the pump shaft seals.
In particular, it protects the pump from projections of dirt from the road in cardan drive installations.

Reference: DEF 054111

Deflector Splines 8-32-36
H NF E 22-131
CARDAN PLATE- DIN 90 and DIN 100
The cardan plate enables the pump shaft to be connected to a cardan shaft
ØG
ØC
ØA
ØB

with interface as on drawing on the right .

Note: the maximum admissible torque is limited by the drive shaft.
The deflector is supplied with the cardan plate.
D E
LEDUC F
Type ØA ØB C D E F ØG H
code DIN 90 4 holes Ø8.5 on Ø74.5
DIN 90 056315 90 47 43 2 10 62 55 15
DIN 100 4 holes Ø10.5 on Ø84
Dimensions in mm.
DIN 100 0519040 100 57 43 2 10 64 55 15
22 TXV - Presentation

TXV series
pumps with
Load Sensing control
variable displacement piston pumps

A D VA N TA G E S

► TXV series pumps are variable displacement with pressure-flow control – called Load Sensing.
They self-regulate to give just the flow required for each movement.

► Specifically designed for the needs of the truck hydraulics market, TXV pumps are particularly
well adapted for applications in:
▪ loader cranes,
▪ forestry cranes,
▪ refuse vehicles,
▪ salt spreaders, snow and ice equipment,
▪ construction equipment vehicles.

► Extremely compact in size to allow direct flange-mounting on vehicle engine or gearbox PTOs.

► TXV pumps are available in 11 models with maximum displacement from 40 to 150 cc/rev.

Maximum pressure is up to 420 bar depending on model.

 Va r i a b l e d i s p l a c e m e n t - T X V 23

Why use a variable

displacement pump?

► Installing a TXV variable displacement pump will transform your hydraulic equipment.
Slow or rapid movements are done with precision, due to the constant adjustment of pump flow rate.

► The pump incorporates a load sensing device to control flow and maximum pressure.
This control device is piloted by a proportional valve which informs the pump of the flow needed for the
different circuits supplied by the pump, independently of pressure.

2 Quick 3 Slow
and precise

1 Slow
and precise

1&3
For slow and precise movements, the pump adjusts its flow to whatever Q
the user needs, whilst also controlling maximum circuit pressure .
TXV series

Oil heating and lamination, and noise level, are considerably reduced
compared to a fixed displacement pump.
Time
The motor driving the pump only provides the power actually
needed by the equipment, thus ensuring:
 longer service life of that equipment;
 significant gains in energy consumption;
 and overall a more environmentally friendly solution .
The proportional movement of
the control lever is perfectly
reproduced by the pump.
2
For rapid movements, the pump supplies the
required flow virtually instantaneously.
24 TXV - How does it work ?

► TXV variable displacement pumps are of axial piston design with 11 pistons, thus ensuring optimal regularity
of flow and a low noise level.

► The displacement of the pump is proportional to the stroke of the pistons .

Displacement – and thus flow - is varied by changing the angle α of the swashplate (Fig .1) .

► To change displacement from maximum to zero (complete flow cancellation),

the swashplate angle goes from α max (Fig . 1) to α min (=0) (Fig . 2) .

Figure 1 - Maximum displacement Figure 2 - zero displacement

Swashplate Bleed screw

Swashplate
Bleed screw
α max

► Setting the servo pump .

Max . pump output pressure (PC)

Standby pressure
setting Direct return to tank
(drain)

Pump pilot
pressure line (LS)
Pressure-flow regulation: "Load Sensing" - TXV 25

Spool ► Zero flow (standby)

LS line Stand-by spring
The proportional valve is closed .
The pressure in the P line increases until it reaches the value at which
the standby spring is set .
P line
Cancellation piston Under the pressure in the P line, the spool moves and oil flow supplies
the setting piston which moves the swashplate into vertical position
Swashplate (angle α =0): no flow, but standby pressure is maintained.The pump
stays in standby mode .

► Full flow
LS line The proportional valve is fully open, allowing passage of pump flow .
The pressure in the LS line is the same as in the P line .
Hydraulic pressure is the same on either side of the spool .
P line The standby spring holds the spool in its closed position .
The cancellation piston is not supplied with oil .
The swashplate is at maximum angle α: the pump is at full
displacement .

► Flow control
LS Line
As soon as the proportional valve tends to reduce the flow
requested by the user, the pressure drop created allows the pump
displacement setting piston to be piloted .
P line This setting piston automatically adjusts pump displacement to match
the order given by the proportional valve .

► Zero flow (maximum pressure)

TXV series

This is the case for example of a cylinder which arrives at a mechanical

LS line stop . The proportional valve is still open .
The pressure of the cylinder at a mechanical stop is sensed by the
P line pump pressure relief valve which opens at the set pressure (PC) .
This allows the pump displacement setting piston to be supplied and
the pump sets itself to a displacement just sufficient to maintain the
circuit pressure .
26 TXV - Characteristics

TXV pumps are available in 11 models from 40 to 150 cc/rev maximum displacement.

Max. peak
Max.speed
Pump Direction Maximum Max. opera- pressure Torque at Max.speed Overhang
at full displa- Weight
reference of rotation displac.(1) ting pressure (intermittent: 300 bar(2) in stand-by torque(4)
cement(3)
5%)
(cc/rev) (bar) (bar) (N.m) rpm rpm (kg) (N.m)

► S tandar d pum p r a nge

0512950 CW
TXV 40 40 400 420 225 3000 3000 26 34
0512955 CCW
0512500 CW
TXV 60 60 400 420 335 2600 3000 26 34
0512505 CCW
0512510 CW
TXV 75 75 400 420 420 2000 3000 26 34
0512515 CCW
0512520 CW
TXV 92 92 400 420 515 1900 3000 26 34
0512525 CCW
0515700 CW
TXV 120 120 380 400 675 2100 3000 26 34
0515705 CCW
0515300 CW
TXV 130 130 365 380 730 2100 3000 28,2 38,6
0515515 CCW
0518600 CW
TXV 150 150 310 330 840 2000 3000 28,2 38,6
0518605 CCW

► With thr ough shaf t *

0518700 CW
TXV 130 130 365 380 730 1900 3000 31,1 47,4
0518705 CCW
* For TXV 130 through shaft available with max displacement set at : 60-65-75-85-95-100-110 - other specific set (on request)
(1) TXV pumps can be set for smaller maximum displacements (see page 41) .
(2) For a mechanical efficiency at 85%.
(3) Higher speed - at full displacement - possible depending on flow required : please contact us.
Viscosity affects maximum possible rotating speed . If viscosity > 400 cSt, please contact us to obtain corresponding speed possibilities .
(4) Value of the overhang torque of the only pump .

► Calculation of power to be supplied to the shaft as a function of flow and pressure

With:
∆P x Q
P= P = Hydraulic power in kW
600 x ŋglobal ∆P = Differential pressure in bar
Q = Flow in l/min
Ca lc u la tio n o f t or que t o det er m i ne P TO ,
C = Torque in N .m
as a fu n c tio n o f th e di s pl ac em ent and t he pr es s ur e
Cyl = Displacement in cc/rev
Cyl x ∆P ŋmeca = Mechanical efficiency
C=
62 .8 x ŋmeca ŋglobal = Mechanical efficiency + volumetric efficiency

► Ideal installation ► Force on pump shaft

Fr : Acceptable max. radial force = 3000 N Fr

Return to the tank Fa : Acceptable axial force = 1600 N. = =

Drain line Fa
Inlet line Application Splined shaft: 8-32-36
Outlet line
circuit DIN ISO 14 - NF 22.131
Pilot line
 Performance - TXV 27

► Torque absorbed as a function of pump output pressure (with a mechanical efficiency considered at 85%)
Torque (N.m)
900

850

800

750

700

650

600

550
TXV40

500 TXV60

450 TXV75

400 TXV92

350 TXV120

300 TXV130*
250 TXV150
200 * TXV with through shaft

150

100

50

0
0 50 100 150 200 250 300 350 400 Pressure (bar)

► Flow as a function of rotating speed

300

250 TXV40

TXV60

200 TXV75
Q (l/min)

TXV92

150 TXV120

*TXV130

100
TXV150

*TXV 130 with through shaft

50 limited at 1900 rpm.

0
0 500 1000 1500 2000 2500 3000

N (rpm)
Flow as a function of speed, with pump in maximum displacement position and oil level in tank above the pump .
TXV series

These graphs are the results of testwork done in HYDRO LEDUC R&D laboratory, on a specific test bench
with a mineral hydraulic fluid ISO VG46 at 25°C (~100 cSt) - disregarding the volumetric efficiency.

► Volumetric efficiency
Efficiency at 1500 rpm
%
100

90
0 100 200 300 360
Pressure (bar)
28 TXV 40 to 120 - Dimensions

TXV 4 0 TO 1 2 0
331.1
125
276
80
Drain G1/2’’
Max. pressure setting (PC) connected to tank 40

stand-by pressure
55.1 setting
LS G1/4"
9

Splined shaft: 8-32-36

DIN ISO 14 - NF 22.131
(DIN 5462)
M12x1.75-6H

247.8
F

40
80 f7

80
194
12.75 (4x)

Connection
for pressure gauge G1/4’’

Dimensions in mm .

View from F View from F

► TXV connect ions

M10x1.5-6H (2x)
Pump Outlet Inlet A B Depth 15 mm to
attach support device Outlet Inlet
reference (Ø) (Ø) (mm) (mm) 6.45

TXV 40 to 92 G 3/4" 15 19
29
25

G 1"1/2

25 A
G 1"
A

TXV 120 6 23 .57

29
6.45

Inlet Outlet

Connection for
pressure gauge G1/4" 28
28
B 36 36 B

CW CCW

► Support device

In cases where it is necessary to use a support device (overhang

torque) for the pump, this must be fixed to the same part which the
pump is mounted on .

► Mass and position of centre of gravity

Overhang
L Weight *Support device
Pump type torque
(mm) (kg)
(N.m)
TXV 40 to 92 130 26 34
Centre of gravity
TXV 120 130 26 34
Screw M10
TXV 130 and TXV 150 128 28 .2 38 .6
M
TXV 130 with through shaft 152 .6 31 .1 47 .4

* This support has to be designed to avoid strain on the pump flange.

 Dimensions - TXV 130-150 29

TXV 1 3 0 - 1 5 0

321.1 127
266 80
Drain G1/2" 40
Maximum pressure setting to be connected to tank

Standby pressure setting LS G1/4"

55.1
9

Splined shaft: 8-32-36

DIN ISO 14 - NF 22.131
(DIN 5462)
M12x1,75-6H

277

40
F
Ø 80 f7

219

80
Ø 12,75 (4x)

Connection for
pressure gauge G1/4"

Dimensions in mm .

View from F View from F

► TXV130 and 150 connections

M10x1.5-6H (2x)
Depth 15 mm to
attach support device
Pump Outlet Inlet A B
reference (Ø) (Ø) (mm) (mm) Outlet
50

TXV 130 and TXV 150

G 1" G 1"1/2 29,4 37
TXV 130 with through shaft
50

Inlet

Connection for
pressure gauge G1/4"
A B
32

CW CCW

► Support device
TXV series

In cases where it is necessary to use a support device (overhang

torque) for the pump, this must be fixed to the same part which the
pump is mounted on .
► Mass and position of centre of gravity
Overhang
L Weight
Pump type torque
(mm) (kg)
(N.m)
TXV 130 et TXV 150 128 28,2 38,6
TXV 130 arbre traversant 152,6 31,1 47,4
30 TXV 130 with through shaft - Dimensions

TXV 1 3 0 T H R OU GH S H A F T P U MP
The TXV 130 pump exists in a “through shaft” version .

With side porting for inlet and output, this “through shaft” TXV 130 configuration means any LEDUC TXV pump, or fixed displacement XPi
or PA pump, can be mounted on the back .
The maximum displacement of the “through shaft” TXV 130 can be factory set, on request, between 60 and 110 cc/rev on request.
It is important to check that maximum torque to be transmitted by the shaft of the “through shaft” TXV 130 does not exceed 900 N .m .
A closing plate must be used when using the pump alone (see page 37) .

Connection for
pressure gauge G1/4"

27
M10x1.5-6H (2x)
Depth 15mm
15 to attach support device

382.6
327.5
Drain G1/2" to be Interface to mount TXV, XPi, PA pumps
Maximum pressure setting connected to tank
(splines 8-32-36 DIN ISO 14 - NF E 22.131)

Standby pressure setting

55.1
9

Splined shaft: 8-32-36

DIN ISO 14 - NF 22.131
(DIN 5462)
281.5
Ø 80 f7

E F
228

57.1

Connection for Splined hub: 8-32-36

pressure gauge G1/4" DIN ISO 14 - NF 22.131

127
80 80
40 40

LS G1/4"

Outlet G1"
Interface to mount
TXV, XPi, PA pumps
M12x1.75-6H
40
80

Ø 12.75 (4x)

View from E View from F

(Shaft side) (Hub side)
Dimensions in mm . Inlet G1 1/2"
 Dimensions - TXV 130 with through shaft 31

TXV 1 3 0 T H R OU GH S H A F T P U MP
View from F (see p.30)

Outlet G1" Inlet G1 1/2"

Inlet G1 1/2" Outlet G1"

CW CCW

► Support device
The support device for the pump must be fixed to the same part which the pump is mounted on (see diagram below) and has to be designed
to avoid strain on the pump flange.

Support device

C C

Example of two TXV pumps. Example of TXV with a PA pump. TXV series

Maximum torque transferable by the shaft

of the pump driven by the PTO:

C = 900 N .m
C

That is, the sum of torque for both pumps must be < 900 N .m .

Example of TXV with a XPi pump.

Please consult our Technical Department for advice regarding your installations .
32 T X VA S A E v e r s i o n - C h a r a c t e r i s t i c s

TXVA series
variable displacement
piston pumps
SAE version
► Characteristics
Max.
Max. peak
Maximum Torque at speed at
Max. pressure Max. speed Overhang
Direc- operating 300 bar full Weight
Pump displacement(1) (intermittent: in stand-by torque(4)
tion of pressure (4350 psi)(2) displace-
ref. 5%)
rotation ment(3)

cu.in/rev (cc/rev) psi (bar) psi (bar) lbf ft (N.m) rpm rpm lbs (kg) lbf ft (N.m)

TXVA CC
4 .60 (75) 5800 (400) 6090 (420) 310 (420) 2000 3000 64 (29) 26 (35 .2)
75 CCW
TXVA CC
5 .60 (92) 5500 (380) 5800 (400) 380 (515) 1900 3000 64 (29) 26 (35 .2)
92 CCW
(1) TXV pumps can be set for smaller maximum displacements (see page 39) .
(2) For a mechanical efficiency at 85%.
(3) Higher speed - at full displacement - possible depending on flow required : please contact us.
(4) Value of the overhang torque of the only pump .

► Configurator for TXVA pumps

To obtain order code for your pump, fill in the
parameters (, , , , , ) TXVA ... ... ... ... . . . . . .
depending on the options required,
      
using the table below .

 TXVA pump
 Displacement 75 92 ...
Clockwise rotation (CW) R
 Direction of rotation
Counterclockwise rotation (CCW) L
SAE C - 2 bolts C1
 Flange
SAE C - 4 bolts C2
Splined
14T 12/24 DP - SAE C S1
SAE J744
 Shaft end
Keyed
Ø1 1/4" UNF 2A - SAE C K1
SAE J744

UNF Inlet : 1 7/8" 12UN 2B

U1
Threaded Outlet : 1 1/16" 12UN 2B
 Ports
Inlet : G1 1/2"
BSP
G1
Threaded Outlet : G 3/4"
Constant Pressure PC

 Control types Flow-Pressure Regulator LS

Closure Plate PF
 P e r f o r m a n c e a n d d i m e n s i o n s - T X VA S A E v e r s i o n 33

► Torque absorbed as a function of ► Flow

pump output pressure (with a mechanical
efficiency considered at 85%)
Torque (lbf ft) Q (gal/min)
500 50

450 45

40
400
35
350
30
300 TXVA 75
25
TXVA 75 TXVA 92
250 20
TXVA 92
200 15

150 10

5
100
0
50 0 500 1000 1500 2000 N (rpm)

0
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000
Pressure (psi)

► Dimensions

2.19 (55.5) 10.91 (277)

1.30 (33) 3.78 (95.95) 8.386 (213) 5.75 (146)
Max.pressure setting 7.126 (181) 4.51 (114.5)

0.51 (13) Standby

S1 pressure setting C1 C2
0.5 (12.7)
Drain G3/8"
Splined shaft SAE J744
5.88 (149.32)

14T 12/24DP
3.76 (95.5)

M8x1.25-6H
Ø 5.00 (Ø126.97)

4.51 (114.5)
5.75 (146)
2 x Ø 0.79 (Ø 20)
3.88 (98.5)

1.10 (28)

4 x Ø 0.56 (Ø 14.3)

1.87 (47.63) 0.31 (7.87) Drain G3/8"

SAE C - 2 bolts (SAE J744) SAE C - 4 bolts (SAE J744)

U1/G1 U1/G1
4.92 (125) 4.92 (125)
2.20 (55.9)
0.51 (13)
K1 0.5 (12.7) R L

Keyed shaft Ø1 1/4" SAE J744

TXV series

U1 : 1-1/16''-12UN-2B 2x 3/8"-16UNC-2B U1 : 1-1/16''-12UN-2B

G1 : G3/4'' depth 0.59 (15)
1.14 (29)

G1 : G3/4''
0.98 (25)

0.59 (15)
0.25 (6.45)
1.38 (35.16)
Ø 5.00 (Ø 126.97)

0.25 (6.45)
0.31 (7.94)

0.59 (15)
Ø 1.25 (Ø 31.73)

0.98 (25)
1.14 (29)

U1 : 1-7/8''-12UN-2B 2x 3/8"-16UNC-2B
G1 : G1-1/2’’ depth 0.59 (15) U1 : 1-7/8''-12UN-2B
1.89 (48) 0.31 (7.87) G1 : G1-1/2’’

0.75 (19) 0.75 (19)

1.10 (28) 1.10 (28)
1.42 (36) 1.42 (36)

Dimensions in inches (mm) .

34 T X VA S A E Ve r s i o n - C o n t r o l s

PC | Co n stan t P ressure
The constant pressure regulator maintains the pressure within a hydraulic receiver. As soon as the set pressure is reached, the pump's flow
adjusts automatically to match the receiver's consumption. This arrangement prevents overheating and power consumption for all pressure
maintenance applications .
Examples:
IMPORTANT::
IMPORTANT
• Hydraulic press Without
Sansfurther specifications
précision in the order:
autre à la commande :
• Compression molds PC
PCréglée
set atà100
100bar .
bar .

• Manufacturing of bonded composites

Installation Safety Limiter

Flow Q
P

PC

Service
pressure P

T (drain G1/2'')
 T X VA S A E Ve r s i o n - C o n t r o l s 35

LS | Fl ow- Pr essure Regulator IMPORTANT::

IMPORTANT
Without
Sansfurther specifications
précision in the order:
autre à la commande :
► Control of Q and P (LS: "Load-Sensing") PCset
PC réglée à 100
at 100 bar,Stand-by
bar, Stand-byat
à 30
30bar .
bar .
This regulation (LS) allows continuous control of the flow and maximum discharge pressure of the pump. With this arrangement, it is easy to
envision all possible combinations:
• High flow and low pressure,
• High pressure and low flow.

Proportional valve
LS
Flow Q

P
A

Stand-by
PC

Service
LS Pressure P
(U1: 9/16''-18UNF-2B
G1: G1/4'')
T drain: (U1: 9/16''-18UNF-2B
G1: G1/2'')

TXV series
36 TXV pumps range with constant torque control

A D VA N TA G E S O F T H E C O N S TA N T T O R Q U E R E G U L AT I O N
► TXV pumps with constant torque control which ensures regulation to maintain Pressure X Flow = Constant

► Control device available for the entire range of TXV pumps from 40 to 150 cc/rev., including the TXV130 model
with through shaft
► Maximum torque between 90 and 700 Nm depending on models
► Torque/power adjustment screw

► Characteristics
Max. peak Max. speed Max. speed
Max. Max. Max.
pressure at full Overhang
Direction displace- operating torque in stand-by Weight
Pump Reference (1) (intermittent displace- torque
ment pressure range(3) mode
of rotation 5%) ment(2)
(cc) (bar) (bar) (daN.m) (rpm) (rpm) (kg) (N.m)
P002685 CW
TXV 40 40 400 420 9 to 43 .5 3000 3000 25 .8 34
P002686 CCW
P002673 CW
TXV 60 60 400 420 9 to 43 .5 2600 3000 25 .8 34
P002674 CCW
P002683 CW
TXV 75 75 400 420 9 to 43 .5 2000 3000 25 .8 34
P002684 CCW
P002681 CW
TXV 92 92 400 420 9 to 43 .5 1900 3000 25 .8 34
P002682 CCW
P002441 CW
TXV 120 120 380 400 12 to 56 .5 2100 3000 25 .8 34
P002442 CCW
P002763 CW
TXV 130 130 365 380 13 to 60 .5 2100 3000 28 38 .6
P002764 CCW
P002765 CW
TXV 150 150 310 330 15 to 70 2000 3000 28 .2 38 .6
P002766 CCW
TXV 130 P002741 CW
(through shaft 130 365 380 13 to 60 .5 1900 3000 31 .1 47 .4
version) P002743 CCW
(1) The pumps can be set for a lower maximum displacement .
(2) Higher speed possible - at full displacement - depending on flow required : please contact Customer Service.
(3) Required torque setting to be specified on order.

► Torque and flow as a function of pressure : ► Constant torque control device :

Example with a maximum torque set at 340 Nm

250
350 LS
300 200 P
250
A
Torque (Nm)

150
Flow (l/min)

200

150 100

Torque
100
Flow
50
50
T
0 0
0 50 100 150 200 250 300 350 400

Pressure (bar)
 Dimensions 37

► Standard pumps dimensions :

TXV40 to 120 TXV130 and 150

321,1
331,10
266
276
194
204
Torque Stand-by pressure Max. pressure Torque Stand-by pressure Max. pressure
setting adjustment setting (PC) LS G1/4" Drain G1/2" setting adjustment setting (PC) LS G1/4" Drain G1/2"

55,1

55,1
9

262,30
Ø 80 f7

227
284
219
247,8
194

Splined shaft 8-32-36

Splined shaft 8-32-36 DIN ISO 14-NF 22.131
DIN ISO 14-NF 22.131 (DIN 5462)
(DIN 5462)

Pressure gauge
connection G1/4" 127 Pressure gauge
connectionG1/4"
80
125
40
80
40

M12x1.75-6H
M12x1.75-6H

40
40

80
80

Ø12,75 (4x)

Ø12,75 (4x)

► TXV130 model with through shaft :

382,6

327,5

255,5 127

80 80
Standby pressure Maximum pressure Drain G1/2"
Torque setting setting setting (PC) LS G1/4" to be connected to tank 40 40

55,1 Interface to mount TXV, XPi, PA pumps

(splines 8-32-36 DIN ISO 14 - NF E 22.131)
Interface to mount
9
TXV, XPi, PA pumps Outlet G1"

Splined shaft: 8-32-36

DIN ISO 14 - NF 22.131
(DIN 5462)

M12x1.75-6H
292,5

E F
40
281,5

40
80 f7

80
80
228

TXV series

12,75 (4x)
.
57,1

Inlet G1 1/2"
View from E View from F
(Shaft side) (Hub side)
Connection for
Splined hub: 8-32-36
pressure gauge G1/4" DIN ISO 14 - NF 22.131

Dimensions in mm .
38 TXV - Accessories

I NL ET F I T T I N GS F OR T X V P U MP S ( opt ional)
See recommendations of the hosing dimensions on page 40.
For high speeds, please consult .

9 0 ° e lb o w fittin gs, swivel

Reference A ØB C D E F Pump type
F
240131 G 1 1/2" 40 60 17 61 77 TXV
240133 G 1 1/2" 50 60 17 65 82 TXV

ØB
E
St r a i gh t fi tti ng s
Reference A ØB C D E Pump type C
D
240182 G 1 1/2" 40 55 16 52 TXV
ØA
240067 G 1 1/2" 48 55 16 64 TXV
240066 G 1 1/2" 60 65 16 67 TXV ØB

240186 G 1 1/2" 63 .5 65 16 67 TXV

240201* G 1 1/2" 76 .2 80 16 87 TXV
E
*Except for TXV130 model with through shaft .

Dimensions in mm . D C

ØA
 TXV - Accessories 39

LS adapter with integrated filter | LEDUC CODE

Filter fitting for LS line connection

Kit reference LS dimension Type of pump
0525567 G1/4″ TXV
C001144 9/16-18 UNF TXVA (SAE)

► Technical characteritics

▪ It protects the LS regulator against contamination coming from the circuit.

▪ Filter can be removed for maintenance.
▪ Filtration: 150 microns.

► Drawings for both versions of the kit ( dimensions in mm):

0525567 Filter C001144

Seal

9/16-18 UNF
9/16-18 UNF
G 1/4″

G 1/4″

29.50 29.57

SE A L + F I LT E R | L E D U C C OD E K000028
The LS filter protects the TXV's Load Sensing valve against contaminations
coming from the hydraulic circuit .
Mounted as standard on all TXV pumps .

KI T C L O S I N G P L AT E + S E A L | L EDUC CODE P001512

FOR TXV 130 THROUGH SHAFT

TXV series

Deflector
CARDAN PLATE - DIN 90 and DIN 100 Splines 8-32-36
NF E 22-131
H
The cardan plate enables the pump shaft to be connected to a cardan shaft
with interface as on drawing on the right .
Note: the maximum admissible torque is limited by the drive shaft.
ØG
ØC
ØA
ØB

The deflector is supplied with the cardan plate.

LEDUC
Type ØA ØB C D E F ØG H D E
code F
DIN 90 056315 90 47 43 2 10 62 55 15
DIN 90 4 holes Ø8.5 on Ø74.5
DIN 100 0519040 100 57 43 2 10 64 55 15
DIN 100 4 holes Ø10.5 on Ø84
Dimensions in mm.
40 Accessories for TXV pumps

FCV - F L U I D VA LV E C IR C U L AT ION | LEDUC CODE: 0524940

The fluid circulation (FCV) is designed for applications where the hydraulic variable displacement pump
is used in standby mode for a long period of time, for example engine PTO, to protect the pump against overheating .

► Technical characteristics

• The valve flow varies between 20 and 22 l/min for a ∆P at 30 bar.

• Maximum pressure is 420 bar .
• The closing pressure is 2 bar min . and 7 bar max .

► Dimensions

A
37 max.* 91.50
45

L 15.5 P

51.50
51.50

56

32

56
LS

G1/4"
8.50

15 33
15
A 57
G1/4" 30

* This lenght varies depending on the setting of L ( see bottom of this page).

► Schematics

Proportional valve

P
LS = LS signal
LS P = Pressure
T = drain
T

Circulation valve

► Setting of the control pressure

Setting of the control pressure LS as a function of L
7
6,5
Control pressure LS (bar)*

6 L
P
5,5
5
4,5 LS
4
3,5
3 T
2,5
2
15 16 17 18 19 20 21 L (mm)

*With a pressure in T line of 0 bar.

 Settings - TXV 41

MAXIMUM DISPLACEMENT SETTING SCREW

TXV 40-120
X
The TXV pumps from 40 to 150 cc/rev are made as standard to be able
to use a setting screw:
▪ Reference : 0518386 for TXV 40 to 120 pumps
▪ Reference : 0523899 for the TXV 130* and TXV 150*
*Except TXV through shaft.
  
The pump displacement can thus be adjusted to exactly what is needed.

► How to set maximum displacement TXV 130-150

Unscrew  completely, loosen nut  and screw  to obtain dimension X on graph below, X
and the corresponding displacement (see figure).

▪ For TXV 150 : 1 turn of the screw changes the displacement by 7.5 cc.
▪ For TXV 130 : 1 turn of the screw changes the displacement by 6.5 cc.
▪ For TXV 120: 1 turn of the screw changes the displacement by 9 cc.
  
▪ For TXV 92 to TXV 40: 1 turn of the screw changes the displacement by 8 cc.

TXV pump | Maximum displacement setting

150
TXV 150 and TXV 150
140
TXV 130 and TXV 130
Displacement of the pump (cc/rev)

130 TXV 120

TXV 92
120

110

100

90

80

70

60

50

40

30
24 26 28 30 32 34 36 38 40 42 44 46 48 50
Dimensions X (mm)

SE TT I N G O F T H E R E GU L AT ION

► Stand-by

TXV pumps are supplied as standard with standby pressure set at 30 bar .
Sérieseries
TXV

On request, this standby pressure can be set between 25 and 60 bar .

► Maximum pressure
TXV

Cancellation pressure PC of the pump must be the same as the maximum working pressure of your installation . This PC pressure should be
specified in the order. If no PC setting is specified, pumps will be supplied with PC set at 100 bar.

► Relief valve in the entry plate of proportional valve

Must be set 25 to 30 bar higher than the chosen PC pressure .

► Response time
Response time of TXV pumps, from zero flow up to full flow, can be adapted.

For further information or advice, please contact our Customer Service Department .
42 Installation and start-up recommendations

OPTIMIZE THE SERVICE LIFE

OF YOUR LEDUC PUMP
► Tank ► Hosing

Generally, hydraulic pumps perform better when the tank is above the The supply line should be dimensioned to ensure fluid speed between
pump . LEDUC pumps can also operate with oil level beneath the pump . 0.5 and 0.8 m/second.
Choose as direct a supply line as possible, avoiding sharp bends .
For further information on such installations, please contact our
Technical Department .
Q = Flow (l/min)
Correct inlet conditions are between 0 .8 to 2 bar absolute pressure . 300 d = Ø inner diameter v = fluid speed
of inlet line (m/s)
200 (mm)
The tank should preferably have a separation between inlet side and
return. This avoids fluid emulsion and the introduction of air into the
0,4
150

Suction
0,5
70
hydraulic circuit . 100 60
90 50
80
70
Ensure also that the suction is not from the very bottom of the tank, 60
40 1,0

30
so as to protect the pump from any deposits (particles) . 50
1,5
25
40
20 2,0

Return
30
15 2,5
3,0
20
Filling filter and venting 10 4,0
9
Clogging indicator 15 8 5,0

Outlet
7
Return filter 6,0
6 7,0
10
Max. level 5 8,0

RETURN 4
Min. level
6
Drain return

Plunging return
► Filtration
The service life of the pumps is highly dependent on the quality of the
hydraulic fluid and level of cleanliness.
Suction raised to prevent
suction of contamination in Separating plate
the bottom of tank Return / Inlet
Opening for oil passage
We recommend the following minimum cleanliness:
(the farther as possible from return)
Ball valve with low ∆P
PUMP INLET

▪ Cleanliness class 9 according to NAS1638;

▪ Cleanliness class 6 according to SAE;
▪ Cleanliness class 20/18/15 according to ISO/DIS 4406.

0.8 bar min. absolute We recommend using of a return filter of 20 µm absolute maximum.
2 bar max.
► Drain pressure
It is essential to drain the pump, to avoid excessive pressures on the
shaft seal . Maximum acceptable internal pressure depends on pump
rotating speed .
Ensure that the working pressure in the housing does not exceed 2
bar, whatever the pump rotation speed and the viscosity of the fluid .
Other operating may be possible; please consult our Technical
Department .
 43

► Preparation of the pump ► Drive and assembly recommendations

Before start-up, the pumps should be filled with clean hydraulic oil. If cardan shaft drive: check the quality and correct installation of the
(minimum 50%). cardan shaft .

For PTO mount applications, be careful to respect the tightening

recommendations in terms of pump onto PTO and PTO onto vehicle
gearbox. (according to the PTO manufacturer's specifications).
If the mounting on the PTO is not lubricated, grease the splines with
graphite grease (example Molycote G rapide) .

LEDUC pumps are not designed to withstand any axial or radial load
on the pump shaft . Check your installation conforms to this require-
ment .

► Elastic support device

For pumps with a greater overhang torque than that accepted by the
PTO, it is recommended to use an elastic support device to support
the weight of the pump .
This support has to be designed to
avoid strain on the pump flange .

► Fluid

Use a mineral hydraulic oil type HLVP according to DIN 51502 (or HV
according to ISO 11158) with viscosity between 10 and 400 cSt .
It is in this viscosity range that the pump keeps its volumetric
characteristics .
We do not sell the elastic support.
The optimal viscosity range is between 20 and 30 cSt . It must be suitable for the environment of the pump assembly.
A maximum viscosity of 1000 cSt is accepted when starting up at low
speed and without pressure . ► Start-up

If you wish to use other fluids, please consult our Customer Service ▪ Open the supply valve if there is one.
Department . ▪ Check the valve is in “back to tank” position.
Maximum temperature of fluid in the pump should not exceed 80°C. ▪ Start up at low speed, or by successive starts/stops.
Fluid viscosities as a function of temperature ▪ Let the pump run for one to two minutes, and check that the flow
10000 is regular .
▪ Check the pump is running correctly, with neither vibrations nor a
1000 normal noise .
mm2/s or cSt

▪ After several hours of operation, check the tightening torque of the

pump on the PTO according to the PTO manufacturer's specifications.
100

► Maintenance

20 Some regular checks are necessary, namely:

Viscosity

▪ tightening of pump to PTO;

12
10 ▪ cleanliness of fluid;
9
8 ▪ state of filter.
7
6
5
4

3.0

-40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110120 130140

Temperature °C
44 Shaft sealing

LEDUC pumps designed for truck hydraulics are all fitted with
reinforced sealing comprising:

►two radial seals :

• an outer seal adapted to the needs of PTOs and gearboxes;
• an inner seal adapted to the hydraulic requirement .

► an original protection of the pump shaft seals :

This is a flexible transparent tube which avoids any entry of
contaminants between the two seals, and guarantees high pressure
water jet cleaning of vehicle will not damage the sealing area. It also
allows air vent of the chamber between the two seals .

WARNING : if you notice any trace of oil in the tube, the tightness
of PTO-pump should be checked immediately .

RECOMMENDATIONS FOR ATTACHING THE PROTECTIVE TUBE

 
 Make a siphon with the tube so as to avoid any  Avoid attaching the tube to any parts which may move,
introduction of dirt from road, and water or damp from this could lead to it being damaged or torn off .
high pressure washing of vehicle .
 Avoid any pinching or folds in the tube when fixing
 Put the end of the tube downwards, or in a place sheltered from it in place .
any projections.
 Make sure the end of the tube is not blocked .
 Fix the tube in place using a collar/clip.

i INFORMATION

HYDRO LEDUC stresses that on non-sealed PTO installations it is the Example of tube attachment
hydraulic pump which ensures the sealing of the vehicle gearbox .

This is why HYDRO LEDUC offers tried and tested solutions approved
by vehicle manufacturers .

Note in particular the pump - PTO sealing has to be done via the seal
C002510 supplied with the pump .
NOTES
46 The LEDUC range

PUMPS FOR MOBILE

PISTON PUMPS & INDUSTRIAL HYDRAULIC
FOR TRUCKS A P P L I C AT I O N S MOTORS

M/MA
MSI
X Pi/XAi T X VA
TXV
Va r i a b l e
M o to r

W/ WA
PA/PAC/PAD

HYDRO LEDUC offers 3 ranges of piston The W series consists of fixed displacement Axial Piston Motors with Constant and
pumps perfectly suited for truck applications, pumps, and the TXVA series consists of Variable Displacement
mountable on power take-off . variable displacement pumps . These pumps
are capable of operating at high pressures ƒ Models from 5 to 180 cc/rev
while occupying minimal space . ƒ DIN and SAE Versions
ƒ Fixed displacement from 12 to 130 cm³/rev ƒ Constant Displacement, Motors without
ƒ Fixed displacement, dual flow, from 2x25 to Leak Oil Connection Special Version .
2x75 cm³/rev ► W Series (ISO) and WA Series
ƒ Variable displacement, with LS (load (SAE)*
sensing) control, from 40 to 150 cm³/rev.
ƒ Fixed displacements from 5 to 180 cm³/
rev
ƒ Flanges according to ISO 3019/2 or
SAE standards
ƒ Shafts according to DIN or SAE
standards

► TXVA Series

ƒ Variable displacements up to 92 cm³/

rev
ƒ SAE shafts and flanges

* For the SAE version, please contact our

Customer Service .
 47

Complete catalog: www.hydroleduc.com

H Y D R O P N E U M AT I C A C -
C U M U L AT O R S MICROHYDRAULIC

Our development team

takes care of your individual
requirements .

In close collaboration with

the decision-makers in
your organization, we work
together with you to develop
Diaphragm, Bladder, Bladder-Diaphragm, and A specific field of application for Hydro Leduc’s solutions according to your
Piston Accumulators in spherical and cylindrical expertise .
designs . specifications.
ƒ Axial and radial piston pumps with
ƒ Storage capacities from 0 .02 to 50 liters constant and variable displacement .
ƒ Operating pressures up to 400 bar ƒ Axial piston micro-hydraulic motors .
ƒ Accessories for operating hydraulic ƒ Micro-hydraulic components (electric
pressure accumulators . drives, valves, control devices, etc) .
ƒ HYDRO LEDUC offers a
comprehensive range of reliable
solutions for extreme applications and
compact spaces .

µ
 A passion for hydraulics

HYDRO LEDUC SAS

Head Office & Factory
BP 9 F-54122 AZERAILLES
FRANCE
Tel. +33 (0)3 83 76 77 40

HYDRO LEDUC GmbH

Am Ziegelplatz 20
D-77746 SCHUTTERWALD
DEUTSCHLAND
Tel. +49 (0) 781-9482590
Fax + 49 (0) 781-9482592

HYDRO LEDUC AB
Betongvägen 11
461 38 TROLLHÄTTAN
SWEDEN
Tel. + 46 (0) 520 10 820

HYDRO LEDUC BV
Ericssonstraat 2
5121 ML RIJEN
THE NETHERLANDS
Tel. +31 161 747816

HYDRO LEDUC N.A. Inc.

Grand Parkway Industrial Park
23549 Clay Road
KATY, TX 77493
USA
Tel. +1 281 679 9654

make it simple
HYDRO LEDUC
SAS with capital of 4 065 000 €
EORI FR31902742100019
RC Nancy B 319 027 421
www.hydroleduc.com
[email protected]

EN_TRUCK PUMPS_20250703