Starting Formulation
SF 1018
Gray Enamel
EPON™ Resin 1001-CX-75 / EPIKURE™ Curing Agent 3115-X-70
Formula Material Supplier Pounds Gallons
Part A
Ti-Pure R-610 Du Pont Company 100.0 2.86
Lampblack 8.0 0.54
Bentone 38 Rheox, Inc. 2.0 0.13
Imperial Anti-Flooding (IAF) RLM Industries, Inc. 3.0 0.14
Compound X-2280
EPON Resin 1001-CX-75 Westlake Epoxy 323.0 36.00
SYN-U-TEX™ 402 Amino Resin Shell Chemical Company 12.9 1.50
Butyl OXITOL™ Glycol Ether Shell Chemical Company 37.5 5.00
Xylene 27.4 3.83
Total Part A 513.8 50.00
Part B
EPIKURE Curing Agent 3115-X-70 Westlake Epoxy 185.5 23.80
2-Propoxyethanol 37.5 5.00
Xylene 152.0 21.20
Total Part B 375.0 50.00
Total Part A & B 888.8 100.00
Mixing Instructions
Pounds Gallons
Part A 513.8 50.00
Part B 375.0 50.00
Part A + B 888.8 100.00
Typical Formulation Table 1 / Formulation Properties
Properties
Units Value
Application Brush or Spray
Generated: May 15, 2024
Issue Date:
Revision:
® and ™ Licensed trademarks of Westlake Inc.
DISCLAIMER
The information provided herein was believed by Westlake. (“Westlake”) to be accurate at the time of preparation or prepared from sources believed to be reliable, but it is the responsibility of
the user to investigate and understand other pertinent sources of information, to comply with all laws and procedures applicable to the safe handling and use of the product and to determine
the suitability of the product for its intended use. All products supplied by Westlake are subject to Westlake’s terms and conditions of sale. WESTLAKE MAKES NO WARRANTY, EXPRESS OR
IMPLIED, CONCERNING THE PRODUCT OR THE MERCHANTABILITY OR FITNESS THEREOF FOR ANY PURPOSE OR CONCERNING THE ACCURACY OF ANY INFORMATION
PROVIDED BY WESTLAKE, except that the product shall conform to Westlake’s specifications. Nothing contained herein constitutes an offer for the sale of any product.
Page 1 of 2
Allow 1 hour induction prior to application and 48 hours before recoating
Cure Schedule Room Temperature cure
Weight per gallon lb/gal 8.88
Total weight solids % 55.4
Vehicle solids % 49.0
Pigment volume concentration (PVC) % 8.2
Volatile Organic Compound (VOC) lb/gal 3.95
g/L 475
Viscosity @ 25°C
Part A KU 84
Part B KU 12 sec
Part A & B KU 62
Storage Recommendations regarding storage conditions can be obtained by visiting our web site
at www.westlakeepoxy.com
General Information
These are starting formulations and are not proven in the user’s particular application but are simply meant to demonstrate the efficacy of the
products and to assist in the development of the user’s own formulation. It is the user’s responsibility to fully-test and qualify the formulation,
along with the ingredients, methods, applications or equipment identified herein (“Information”), by the user’s knowledgeable formulator or
scientist, and to determine the appropriate use conditions and legal restrictions, prior to use of any Information.
Safety, Storage & Handling
Please refer to the MSDS for the most current Safety and Handling information.
Exposure to these materials should be minimized and avoided, if feasible, through the observance of proper precautions, use of appropriate
engineering controls and proper personal protective clothing and equipment, and adherence to proper handling procedures. None of these
materials should be used, stored, or transported until the handling precautions and recommendations as stated in the Material Safety Data Sheet
(MSDS) for these and all other products being used are understood by all persons who will work with them. Questions and requests for
information on Westlake Epoxy products should be directed to your Westlake Epoxy sales representative, or the nearest Westlake Epoxy sales
office. Information and MSDSs on non-Westlake Epoxy products should be obtained from the respective manufacturer.
Contact Information
For product prices, availability, or order placement, please contact customer service:
www.westlakeepoxy.com/Contacts/
For literature and technical assistance, visit our website at:www.westlakeepoxy.com
Generated: May 15, 2024
Issue Date:
Revision:
® and ™ Licensed trademarks of Westlake Inc.
DISCLAIMER
The information provided herein was believed by Westlake. (“Westlake”) to be accurate at the time of preparation or prepared from sources believed to be reliable, but it is the responsibility of
the user to investigate and understand other pertinent sources of information, to comply with all laws and procedures applicable to the safe handling and use of the product and to determine
the suitability of the product for its intended use. All products supplied by Westlake are subject to Westlake’s terms and conditions of sale. WESTLAKE MAKES NO WARRANTY, EXPRESS OR
IMPLIED, CONCERNING THE PRODUCT OR THE MERCHANTABILITY OR FITNESS THEREOF FOR ANY PURPOSE OR CONCERNING THE ACCURACY OF ANY INFORMATION
PROVIDED BY WESTLAKE, except that the product shall conform to Westlake’s specifications. Nothing contained herein constitutes an offer for the sale of any product.
Page 2 of 2
