CFP-16
Conventional Fire Alarm Control Panel
Conventional Fire Systems
GENERAL
The Notifier CFP-16 conventional fire control panel is designed
to be used as a component of a fire alarm control system.
The CFP-16 system is suitable for small to medium sized
buildings and is fully compliant with the New Zealand standard
NZS4512:2010 and New Zealand building code.
The standard panel is equipped with 8 Zones but may be
extended to 16 Zones by the addition of an 8 Zone expansion
module.
The CFP-16 is extremely flexible and can be programmed to
meet the demands of a wide variety of building types.
The CFP-16 panel is compatible with the Notifier range of
conventional heat detectors, manual call points and System
Sensor smoke detectors plus a variety of other conventional
fire detection products.
Initiating Device Circuits (Zones)
FEATURES
• 8 or 16 zone interface circuits
• 8 Zones - expandable to 16 Zones
• Compatible with SYSTEM SENSOR 100 series devices
• 2 x 40 character LCD display providing a simple user
(refer to CFP-16 manual for complete list of compatible
friendly interface
devices)
• 24 character plain English zone descriptor
• Smart menu driven display for clear annunciation, Notification Applicance Circuits (NACs)
simple interrogation, configuration and control
• Flexible full featured programmability • Three independently programmable output circuits
• Each zone can be configured for a range of different • All circuits are power-limited and supervised by 4k7
device type functions Ohm End of Line (EOL) resistor.
• Each output can be programmed for different functional • Up to 1A power per NAC
and cause & effect requirements
• Compact 5.6 or 11 Amp system power supply and Auxiliary Outputs
charger
• Inbuilt programmable Occupant Warning System 30, • Three independently programmable relay outputs,
60 or 120 Watts preconfigured for Alarm, Fault (normally energized)
• Optional 8 way programmable relay modules and Disable.
• Optional OWS control, display and microphone module • Auxiliary power output (internal only).
• Front or Rear service options • One Door Holder output circuit, fused at 3A.
• Two cabinet sizes 650 mm and 900 mm
• ACM-ZM - LED Zone mimic interface module NOTE: The total power requirement of the FACP and any additional
• Remote slim LED mimic options (425mm or 900mm) NAC and Auxiliary outputs must not exceed the capacity of the
installed power supply system.
DOC-02-141:rev C - Page 1 of 2
PRODUCT LINE INFORMATION Electrical Specifications
FG-32-001 - CFP-16/650-8Z-PS5: CFP-16 Base Panel 650mm cab, 8 AC Power: NPS-5 fitted: 240vac, 0.8A, 50Hz. NPS-11 fitted: 240vac,
Zone, 5A PSU (Including: EBCO switches, Door switch and ACM-ZM 1.5A, 50Hz. Input Fuse: M205 8.0A, 250V.
8 Zone mimic interface Module)
Current Draw: Quiescent: 100mA, Defect: 110mA, Alarm: 240mA (for
FG-32-002 - CFP-16/900-8Z-PS5: CFP-16 Base Panel 900mm cab, 8 8 zone panel)
Zone, 5A PSU (Including: EBCO switches, Door switch and ACM-ZM
8 Zone mimic interface Module) Battery: Two 12V Sealed lead Acid batteries. Battery charger capacity:
7AH-85AH (CAB650 and CAB900 enclosures hold maximum of two
FG-32-003 - CFP-16/650-8Z-PS11: CFP-16 Base Panel 650mm cab, 33AH batteries)
8 Zone, 11A PSU (Including: EBCO switches, Door switch and ACM-
ZM 8 Zone mimic interface Module) Initiating Device Circuits: Power-limited, supervised circuit. End-of-
Line Resistor: 4k7 ohm, ½ watt.
FG-32-004 - CFP-16/900-8Z-PS11: CFP-16 Base Panel 900mm cab,
8 Zone, 11A PSU (Including: EBCO switches, Door switch and ACM- Notification Appliance Circuits: Power-limited, supervised circuit.
ZM 8 Zone mimic interface Module) Maximum current per circuit: 1.0A. End-of-Line Resistor: 4k7 ohm,
½ watt.
FG-72-021 - NZ Acrylic (FS) kit: inc Annun.Plates CAB650 (CFP-16)
Programmable Relays: Contact Rating: 1.0A @ 30V DC (resistive)
FG-72-022 - NZ Acrylic (FS) kit: inc Annun.Plates CAB900 (CFP-16)
Door Holder Output: Powered output protected by automotive fuse.
FG-72-026 - CAB650 Rear Service Mimic Surround Kit Rating: 3.0A @ 30V DC (resistive)
FG-72-027 - CAB900 Rear Service Mimic Surround Kit Auxiliary Power (internal only): 24VDC power limited output for
auxiliary devices installed within enclosure.
ASY-01-039 - ZEM-8: Eight zone expansion module; to expand from
Cabinet Specifications
8 to 16 zones
CAB650: 650mm(h) x 450mm(w) x 190mm(d)
ASY-02-022 - ACM-8RA: Relay module which provides eight
individually configurable (C/NO/NC) relay contacts.
CAB900: 900mm(h) x 450mm(w) x 190mm(d)
ASY-01-026 - AEM-ZM: IFS-721 8 zone mimic expansion card
CAB650/BB: 300mm(h) x 450mm(w) x 190mm(d)
ASY-01-048 - SGD: SGD interface to suit CFP-16NZ
Material: 1.2mm Zinc Sealed Steel
ASY-01-043 - ANP: Annuciator name plate
All cabinets are powder-coated charcoal texture. Dulux code: 88351
For further variants please contact your nearest Notifier Sales Office. Temperature And Humidity
This system has been certified for operation at 0o to 55oC and at a
SPECIFICATIONS relative humidity 10% to 93%
System Capacity
AGENCY LISTINGS AND APPROVALS
• Initiating device circuits (zones) . . . . . . . . 8 or 16
• ACM-ZM . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Certified to NZS4512:2010
• ACM-8RA . . . . . . . . . . . . . . . . . . . . . . . . . 28 FPA Register # NI/102
• Expansion modules (total) . . . . . . . . . . . . 32
This document is not intended for installation purposes. We try to
For more information please contact your
keep our product information up-to-date and accurate. We cannot
nearest Notifier Office or Distributor
cover all specific applications or anticipate all requirements. All
specifications are subject to change without notice.
www.notifier.com.au | www.notifier.co.nz
ISO9001
FS 520324
© 2014 Honeywell Ltd
ENGINEERING & MANUFACTURING
QUALITY SYSTEMS
DOC-02-141:rev C - Page 2 of 2
