DETAILS OF MEASUREMENTS

Estimate Items
State Division
Branch Sub-Division
Name of Work : Annual comprehensive maintenance of Outreach OPD, Hospital and Residential complex at NCI
Jhajjar campus of AIIMS New Delhi (SH: II A/R & M/O and special repair work.)

SNo Item No Description Number Length Breadth Height Weight Qty

1.1 2.1.1 2.1 Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as
10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lif upto 1.5 m, as
directed by Engineer-in- Charge:
2.1.1 All kinds of soil
1 Approx 1 100 100
Total 100
Total (Rounded) 100.00 sqm
2.1 2.6.1 2.6 Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas
(exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of
excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge.
2.6.1 All kinds of soil
1 NCI Back side STP 1 370 0.3 0.45 2 99.9
Total 99.9
Total (Rounded) 99.90 cum
3 2.25 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers
not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50
and for all lif .
1 Approx. 1 1000 1000
Total 1000
Total (Rounded) 1,000.00 cum
4.1 2.28.1 2.28 Surface dressing of the ground including removing vegetation and in- equalities not exceeding 15 cm
deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.
2.28.1 All kinds of soil
1 Approx 1 1000 1000
Total 1000
Total (Rounded) 1,000.00 sqm
5 2.31 2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth
up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m
outside the periphery of the area cleared.
1 Approx 1 5000 5000
Total 5000
Total (Rounded) 5,000.00 sqm
6.1 4.1.2 4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering
and shuttering - All work up to plinth level :
4.1.2 1:1.5:3 (1 Cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate
20 mm nominal size derived from natural sources)
1 Approx 1 20 20
Total 20
Total (Rounded) 20.00 cum

6.2 4.1.3 4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering
and shuttering - All work up to plinth level :
4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20
mm nominal size derived from natural sources)
1 NCI Back side STP 1 370 0.23 0.075 2 12.76
2 Approx 1 17.24 17.24
Total 30
Total (Rounded) 30.00 cum

/2025 JAN 24 AR & MO WORK FOR AMC Page 1 of 36

SNo Item No Description Number Length Breadth Height Weight Qty

6.3 4.1.10 4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering
and shuttering - All work up to plinth level :
4.1.10 1:5:10 (1 cement : 5 coarse sand (zone-Ill) derived from natural sources : 10 graded stone
aggregate 40 mm nominal size derived from natural sources)
1 NCI Back side STP 1 370 0.3 0.1 2 22.2
2 Approx 1 7.8 7.8
Total 30
Total (Rounded) 30.00 cum
7.1 4.3.1 4.3 Centering and shuttering including strutting, propping etc. and removal of form work for:
4.3.1 Foundations, footings, bases for columns
1 Approx 1 50 50
Total 50
Total (Rounded) 50.00 sqm
7.2 4.3.3 4.3 Centering and shuttering including strutting, propping etc. and removal of form work for:
4.3.3 Columns, piers, abutments, pillars, posts and struts
1 Approx 1 20 20
Total 20
Total (Rounded) 20.00 sqm
8.1.1 4.20.1.4 4.20 Providing and laying in position ready mixed or site batched design mix cement concrete for plain
cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland
Pozzolana/ Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS:
9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing
strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost
of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of
concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be
payable separately. In case the cement content in design mix is more than 110% of the minimum specified
cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra
cement.
4.20.1 All works upto plinth level :
4.20.1.4 Concrete of M25 grade with minimum cement content of 300 kg /cum
1 Approx. 1 10 10
Total 10
Total (Rounded) 10.00 cum
8.2.1 4.20.2.2 4.20 Providing and laying in position ready mixed or site batched design mix cement concrete for plain
cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland
Pozzolana/ Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS:
9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing
strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost
of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of
concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be
payable separately. In case the cement content in design mix is more than 110% of the minimum specified
cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra
cement.
4.20.2 All works above plinth and upto floor V level
4.20.2.2 Concrete of M15 grade with minimum cement content of 240 kg /cum
1 Approx 1 10 10
Total 10
Total (Rounded) 10.00 cum

9.1 5.9.5 5.9 Centering and shuttering including strutting, propping etc. and removal of form for
5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers
1 NCI Back side STP 1 370 0.075 2 2 111
Total 111
Total (Rounded) 111.00 sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 2 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
10.1 5.22.6 5.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position
and binding all complete upto plinth level.
5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more.
1 Approx. 1 250 250
Total 250
Total (Rounded) 250.00 kg
11.1 6.1.2 6.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation
and plinth in:
6.1.2 Cement mortar 1:6(1 cement :6 coarse sand)
1 NCI Back side STP 1 370 0.23 0.6 2 102.12
Total 102.12
Total (Rounded) 102.12 cum
12.1 6.3.1 6.3 Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5
conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1
cement: 6 coarse sand) :
6.3.1 With F.P.S.(non modular) bricks
1 Approx 1 2 2
Total 2
Total (Rounded) 2.00 cum
13.1 6.28.1 6.28 Brick work with common burnt clay machine moulded modular bricks of class designation 12.5 in
exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in
cement mortar 1:6 (1 cement : 6 coarse sand).
6.28.1 From ground level upto plinth level
1 Approx 1 5 5
Total 5
Total (Rounded) 5.00 cum
14 6.44 6.44 Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular)
bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).
1 Approx 1 200 200
Total 200
Total (Rounded) 200.00 metre
15 8.19 8.19 Extra for stone work for wall lining on exterior walls of height more than 10 m from ground level for
every additional height of 3 m or part there of .
1 Approx. 1 30 30
Total 30
Total (Rounded) 30.00 sqm
16.1 8.20.1 8.20 Providing and fixing dry cladding upto 10 metre height with 30 mm thick gang saw cut stone with
machine cut edges of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with
the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural
drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall
be paid for separately).
8.20.1 Red sand stone - 30 mm thick gang saw cut stone
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 sqm
16.2 8.20.2 8.20 Providing and fixing dry cladding upto 10 metre height with 30 mm thick gang saw cut stone with
machine cut edges of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with
the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural
drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall
be paid for separately).
8.20.2 White sand stone - 30 mm thick gang saw cut stone
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 3 of 36

SNo Item No Description Number Length Breadth Height Weight Qty

17 8.21 8.21 Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with
machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube in the required
pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be
fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the
frame and embedded in brick wall with cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded
stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centring and
shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary
holes. Approved cramps/ pins etc. shall be welded to the frame work to support stone cladding, the steel
work will be given a priming coat of Zinc primer as approved by Engineer-in-charge and painted with two or
more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-charge for
approval before execution). The frame work shall be fixed in true horizontal & vertical lines/planes. (Only
structural steel frame work shall be measured for the purpose of payment, stainless steel cramps shall be paid
for separately and nothing extra shall be paid).
1 Approx. 1 120 120
Total 120
Total (Rounded) 120.00 kg
18 8.22 8.22 Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size,
adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gram), for dry stone
cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling
required holes etc complete as per direction of the Engineer-in-charge.
1 Approx. 1 200 200
Total 200
Total (Rounded) 200.00 each
19.1 8.28.1 8.28 Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1),
for plain lining / cladding with necessary screws, including priming coat on unexposed surface with:
8.28.1 Decorative veneer facings of approved manufacture
1 Approx 1 100 100
Total 100
Total (Rounded) 100.00 sqm
20.1 9.1.1 9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought
framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast
lugs or dash fastener shall be paid for separately).
9.1.1 Second class teak wood
1 Approx 1 2 2
Total 2
Total (Rounded) 2.00 cum
21.1 9.21.2 9.21 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative
type, core of block board construction with frame of 1st class hard wood and well matched commercial 3
ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:
9.21.2 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
1 Approx. 1 40 2.05 0.96 78.72
Total 78.72
Total (Rounded) 78.72 sqm
22.1 9.62.2 9.62 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete
(Copper oxidised as per IS 1378)
9.62.2 250x16 mm
1 Approx. 1 40 40
Total 40
Total (Rounded) 40.00 each

23.1 9.71.2 9.71 Providing and fixing IS: 12817 marked stainless steel butt hinges (heavy weight) with stainless steel
screws etc. complete :
9.71.2 100x60x2.50 mm
1 Approx. 1 40 3 120
Total 120

/2025 JAN 24 AR & MO WORK FOR AMC Page 4 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
Total (Rounded) 120.00 each
24 9.76 9.76 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of
lever handles of approved quality with necessary screws etc. complete.
1 Approx. 1 40 40
Total 40
Total (Rounded) 40.00 each
25.1 9.111.1 9.111 Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling
etc. with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood.
9.111.1 50x50 mm (base and height)
1 Approx 1 30 30
Total 30
Total (Rounded) 30.00 metre
26.1 9.114.1 9.114 Providing and fixing magnetic catcher of approved quality in cupboard/ ward robe shutters, including
fixing with necessary screws etc. complete.
9.114.1 Triple strip vertical type
1 Approx 1 50 50
Total 50
Total (Rounded) 50.00 each
26.2 9.114.2 9.114 Providing and fixing magnetic catcher of approved quality in cupboard/ ward robe shutters, including
fixing with necessary screws etc. complete.
9.114.2 Double strip (horizontal type)
1 Approx 1 50 50
Total 50
Total (Rounded) 50.00 each
27.1 9.127.2 9.127 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/
suede finish with high density protective surface layer and reverse side of adhesive bonding quality
conforming to IS : 2046 Type S, including cost of adhesive of approved quality.
9.127.2 1.0 mm thick
1 Door 1 50 2 2.05 0.96 196.8
2 For CupBoard 1 100 100
3 L.S 1 2.13 2.13
Total 298.93
Total (Rounded) 298.93 sqm
28.1 9.140.1 9.140 Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of
approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of
Engineer-in- charge (Frame work shall be paid for separately).
9.140.1 12 mm thick commercial ply conforming to IS : 1328 BWR type
1 Approx 1 100 100
Total 100
Total (Rounded) 100.00 sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 5 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
29.1 9.162A.1 9.162A Providing and fixing factory made ISI marked uninsulated metal fire rated doorset assembly for all
non egress application areas like shafts etc consisting of galvanized iron steel frame and double leaf shutter,
including necessary hardware accessories conforming to FD 120 UD classification of IS 3614 :2021 with fire
rating of 120 minutes integrity_ The door frame and shutter shall be made out of minimum 1.20 mm thick GI
Sheet with minimum 120 GSM Zinc coating as per IS. 277. The entire fire rated doorset assembly shall be
tested in unlatched condition as per IS 17518 (Part -1): 2022 Frame The frame shall be of minimum size 90
x 60 mm with grooved profile to take appropriate fire rated smoke seal, having mitred cut joints (self
tab/screwed assembled at site) and provided with appropriate reinforcement suitable for taking hardware
and flush fixing as per IS: 4351. The smoke seal material shall be of EPDM in accordance with / ASTM
E-84 of minimum size 10 mm x 4 mm, fixed within the inbuilt groove or stuck with adhesive on the entire
perimeter of the frame. The door frame shall be fixed in all four sides to masonry wall opening with
CSK/Flex headed fastener of minimum 8 mm dia size and minimum 80 mm long with 8mm dta polyamicle
sleeves @ 4 numbers at each on vertical sides (up to 2100 mm height) and 2 numbers each on top and
bottom sides. Door shutter: The double skin double leaf door shutter shall be consisting of minimum 46 mm
thick and having box like structure. slots cut and holes punched, for fixing hardwares with stifners as per IS:
16074 including resin bonded honey comb paper core infill material of density 5 kg/cum Integral astragals
to be provided on meeting styles of double leaf door, each on active and inactive leaf_ The door shutters
shall be mounted on the frame with SS 304 grade ball bearing butt hinges as per EN 1935:2002 or butt
hinges as per IS 12817 both, of minimum size 100x75x3 mm @ minimum 4 numbers hinges per door leaf
upto 2100 mm / 2400 mm height or as per test evidence, which ever is more, fixed with M6 25 screws. All
doors shall be factory prepared for receiving appropriate hardware and provided with necessary
reinforcement for hardware accessories. Accessories Hardware Fire doorset shall be provided with one
number fire rated SS304 grade shaft mortise dead lock, one number 50 mm to 80 mm Back Set with
minimum 20mm Square forend with alien key including SS304 dead strike plate conforming to IS
16015:2022 /EN 12209. Two numbers recessed flush pull handle (SS 304) of minimum size 40 mm x 120
mm. One number 300 mm long concealed lever action flush bolt (Dye-Cast Stainless Steel Finish) at bottom
with SS dust proof socket and one number minimum 300 mm long concealed flush bolt (Dye-Cast Stainless
Steel Finish) at top of inactive leaf of double door, as approved by the Engineer-in-charge. Finishing. Both
frame and door shutters shall be factory finished with polyester powder coating of minimum 50 microns
thick and shall have passed salt spray test as per IS:13871 of approved colour and shade all
complete as per manufacturer's specifications and as per direction of the Engineer-in-charge. Installation:
The hollow space in the door frame shall be filled / iniected with fire rated self extinguishing type
polyurethane foam (PUF) afer installation at site of work. Rate shall include for complete fire rated door
assembly supply and installation by the approoved manufacturer.
9.162A.1 Double leaf un-insulated fire rated door of FD 120 UD classification with 120 minutes integrity
only as per IS 3614:2021 for non egress application area like shafts etc.
1 Approx 1 10 10
Total 10
Total (Rounded) 10.00 sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 6 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
30.1 9.162B.1 9.162B Providing and fixing factory made 151 marked un-insulated metal fire rated doorset assembly for all
non egress application areas like shafts etc. consisting galvanized iron steel frame and single leaf
shutter including necessary hardware accessories conforming to FD 120 UD classification of IS 3614
:2021 with fire rating of 120 minutes integrity. The door frame and shutter shall be made out of minimum
1_20 mm thick GI Sheet with minimum 120 GSM Zinc coating as per IS: 277. The entire fire rated doorset
assembly shall be tested in unlatched condition as per IS 17518 (Part -1): 2022 Frame The frame shall be of
minimum size 90 x 60 mm with grooved profile to take appropriate fire rated smoke seal, having mitred cut
joints (self tab/screwed assembled at site) and provided with appropriate reinforcement suitable for taking
hardware and flush fixing as per IS: 4351. The smoke seal material shall be of EPDM tested in accordance
with ASTM 84 of minimum size 10x4 mm, fixed within the inbuilt groove or stuck with adhesive on the
entire perimeter of the frame. The door frame shall be fixed in all four sides to masonry wall opening with
CSK/Hex headed fasteners of minimum 8 mm dia size and minimum 80 mm long with 8mm dia polyamide
sleeves @ 4 number at each on vertical sides (up to 2100 mm height) and 2 numbers each on top and bottom
sides_ Door shutter: The double skin single leaf door shutter shall be consisting of minimum 46 mm thick
and having box like structure, slots cut and holes punched, for fixing of hardwares with stiffeners as per IS:
16074 including Resin bonded honey comb paper core iMill material of density 5 kg/cum. The door shutter
shall be mounted on the frame with SS 304 grade ball bearing butt hinges as per EN 1935 : 2002 or butt
hinges as per IS 12817 both, of minimum size 100x75x3 mm @ minimum 4 numbers up to 2100 mm / 2400
mm height or as per test evidence, which ever is more, fixed with M6 25 screws. All doors shall be factory
prepared for receiving appropriate hardware and provided with necessary reinforcement for hardware
accessories. Hardware Accessories : Fire doorset assembly shall be provided with one number fire rated SS
304 shaft mortise dead lock, one number 50-80 mm Back Set with minimum 20 mm Square forend with
alien key including S5304 dead strike plate conforming to IS:. 16015:2022/EN 12209, one number
recessed flush pull handle (SS304) of minimum size 40 mm x 120 mm, as approved by Engineer-in-Charge.
Finishing: Both frame and door shutters shall be factory finished with polyester powder coating of minimum
50 microns thick and shall. have passed salt spray test as per IS.13871 of approved colour and shade
all complete as per manufacturers specifications and as per direction of the Engineer-in-charge.
Installation: The hollow space in the door frame shall be filled 1 injected with fire rated self extinguishing
type polyurethane foam (PUF) after installation at site of work. The rate shall be inclusive of complete fire
rated door assembly, supply and installatIon by the approved manufacturer.
9.162B.1 Single leaf un-insulated metal fire rated door and frame of FO 120 UD with 120 minutes integrity
only as per IS 3614:2021 - For non egress application like area shafts etc.
1 Approx 1 10 10
Total 10
Total (Rounded) 10.00 sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 7 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
31.1 9.162C.1 9.162C Providing and fixing factory made IS! marked un-insulated metal fire rated doorset assembly for all
egress applications areas like utility rooms and service areas consisting of galvanized iron steel frame and
double leaf shutter including necessary hardware accessories, conforming to FD 120 UD classification of IS
3614 :2021 with fire rating of 120 minutes integrity. The door frame and shutter shall be made out of
minimum 1.20 mm thick GI Sheet with minimum 120 GSM Zinc coating as per IS: 277. The entire fire rated
doorset assembly shall be tested in unlatched condition as per IS 17518 (Part - 1): 2022 Frame , The frame
shall be of minimum size 90 x 60 mm with grooved profile to take appropriate fire rated smoke seal, having
mitred cut joints (self tab/screwed assembled at site) and provided with appropriate reinforcement suitable
for taking hardware and flush fixing as per IS: 4351. The smoke seal material shall be of EPDM tested in
accordance with ASTM E- 84 of minimum size 10x4 mm, fixed within the inbuilt groove or stuck with
adhesive on the entire perimeter of the frame. The door frame shall be fixed in all three sides to masonry
wall opening with CSKJHex headed fasteners of minimum 8 mm dia size and minimum 80 mm long with
8mm dia polyamide sleeves @ 5 numbers at each on vertical side and 3 numbers on top side. Door shutter:
The double skin double leaf door shutter shall be consisting of minimum 46 mm thick and having box like
structure, slots cut and holes punched for fixing of hardware with stifener as per IS 16074 including Resin
bonded honey comb paper core infill material of density 5 kg/cum. Each door leaf shall be provided with
vision panel, having maximum area of 0.12 sqm, of 120 minute fire rated minimum 6 mm thick clear
borosilicate glass pane fixed with clip-on arrangement and fire rated ceramic tape having minimum size
13x2mm to be fixed all around the glass on both the sides. Integral astragals to be provided for double leaf
doors on the meeting style each on both active and inactive leaf. The door shutters shall be mounted on the
frame with SS 304 grade ball bearing butt hinges as per EN 1935 : 2002 or butt hinges as per IS 12817 both,
of minimum size 100x75x3 mm @ 5 numbers hinges per door leaf upto 2400 mm height or as per test
evidence. which ever is more, fixed with M6 25 screws. All doors shall be factory prepared for receiving
appropriate hardware and provided with necessary reinforcement for hardware accessories. Hardware
Accessories: Fire doorset shall provided with one number fire rated SS 304 grade Mortise dead lock, 50-80
mm Back Set, minimum 20 mm Square forend with alien key Escutcheon of Stainless Steel, and 65/70 mm
cylinder with both side key conforming to IS: 16015:2022/EN12209, two pair of D type Pull handle of SS
304 grade of minimum 22 mm dia Centre to centre distance of 300 mm back to back fixing with spindle, one
number 300 mm long Concealed lever action flush bolt (Dye-Cast Stainless Steel Finish) at bottom with SS
dust proof socket and one number 600 mm long Concealed lever action flush bolt (Dye-Cast Stainless Steel
Finish) on top of inactive leaf of double door. Two number fire rated surface mounted heavy duty door closer
of size EN 3-5 with standard arm, of desired finish conforming to IS 3564/EN 1154. Finishing: Both frame
and door shutters shall be factory finished with polyester powder coating of minimum 50 microns thick and
shall have passed salt spray test as per IS:13871 of approved colour and shade all complete as per
manufacturer's specifications and as per direction of the Engineer-in-charge. Installation: The hollow space
in the door frame shall be filled / injected with fire rated self extinguishing type polyurethane foam (PUF)
after installation at site of work. The rate shall be inclusive of complete fire rated door assembly, supply and
installation by the approved manufacturer.
9.162C.1 Double leaf un-insulated metal fire rated doorset of FD 120 UD classification with 120 minutes
integrity only as per IS 3614:2021 - For egress application like utility room and service area etc.
1 Approx 1 10 10
Total 10
Total (Rounded) 10.00 sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 8 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
32.1 9.162D.1 9.162D Providing and fixing factory made ISI marked un-insulated metal fire rated doorset assembly, for all
egress applications areas like utility rooms and service areas etc , consisting of galvanized iron steel frame
and single leaf shutter including necessary hardware accessories conforming to FD 120 UD classification of
IS. 3614:2021 with fire rating of 120 minutes integrity. The door frame and shutter shad be made out of
minimum 1.20 mm thick GI Sheet with minimum 120 GSM Zinc coating as per IS: 277_ The entire fire rated
doorset assembly shall be tested in unlatched condition as per IS 17518 (Part - 1). 2022 Frame : The frame
shall be of minimum size 90 x 60 mm with grooved profile to take appropriate fire rated smoke seal, having
mitred cut joints (self tab/screwed assembled at site and provided with appropriate reinforcement suitable
for taking hardware and flush fixing as per IS. 4351. The smoke seal material shall be of EPDM tested in
accordance with ASTIVI E- 84 of minimum 10 x 4 mm, fixed within the inbuilt groove or stuck with
adhesive on the entire perimeter of the frame. The door frame shall be fixed in all three sides to masonry
wall opening with CSK/Hex headed fasteners of minimum 8 mm dia size and minimum 80 mm long with
8mm die polyamide sleeves @ 5 numbers at each on vertical side and 2 numbers on top side Door shutter:
The double skinned single leaf door shutters shall be consisting of minimum 46 mm thick and having box
like structure, slots cut and holes punched, for fixing of hardwares with stiffners as per IS: 16074 including
resin bonded honey comb paper core infill material of density 5 kg/curn. Door leaf shall be provided with
vision panel, having maximum area of 0.12 sqm. of 120 minute fire rated minimum 6 mm thick clear
borosilicate glass pane fixed with clip-on arrangement and fire rated ceramic tape having minimum size 13x2
mm to be fixed all around the glass on both the sides. The door shutter shall be mounted on the frame with
SS 304 grade ball bearing butt hinges as per EN 1935 : 2002 or butt hinges as per IS 12817, of minimum
size 100x75x3 mm @ 5 numbers hinges upto 2400rnm height or as per test evidence, whichever is more,
fixed with M6 25 screws. All doors shall be factory prepared for receiving appropriate hardware and
provided with necessary reinforcement for hardware accessories. Accessories Hardware : Fire doorset shall
be provided with one number fire rated SS 304 grade mortise dead lock, 50-80 mm backset with minimum
20 mm square forend with alien key including Escutcheon of stainless steel (SS304) with 65/70 mm cylinder
both side key conforming to EN:12209 / IS 16015:2022, one pair of D type pull handle of stainless steel
(5S304) of minimum 22 mm dia centre to centre distance of 300 mm back to back fixing with spindle, one
number 120 minutes fire rated surface mounted heavy duty door closer of size EN 3-5 with standard arm of
desired finish conforming to IS: 3564/EN1154 Finishing: Both frame and door shutters shall be factory
finished with polyester powder coating of minimum 50 microns thick and shall have passed salt spray test
as per IS!13871 of approved colour and shade all complete as per manufacturer's specifications and
as per direction of the Engineer-in-charge. Installation: The hollow space in the door frame shall be filled /
injected with fire rated self extinguishing type polyurethane foam (PUF) after installation at site of work. The
rate shall be inclusive of complete fire rated door assembly, supply and installation by the approved
manufacturer.
9.162D.1 Single leaf un-insulated metal fire rated doorset of FD 120 UD classification with 120 minutes
integrity as per IS 3614.2021 For non egress applications like utility room and service area etc
1 Approx 1 10 10
Total 10
Total (Rounded) 10.00 sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 9 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
33.1 9.162E.1 9.162E Providing and fixing factory made ISI marked partially insulated metal fire rated doorset assembly,
for staircase / exit pathway and refuge areas al)plications, consisting of galvanized iron steel frame and
single leaf shutter including necessary hardware accessories, conforming to FD 120 PI classification of IS
3614 .2021 with fire rating of 120 minutes integrity and 30 minutes insulation. The door frame and shutter
shall be made out of minimum 1.20 mm thick GI Sheet with minimum 120 GSM Zinc coating as per IS: 277.
The entire fire rated doorset assembly shall be tested in latched condition as per IS 17518 (Part -1): 2022
Frame: The farme shall be of minimum size 90 x 60 mm with grooved profile to take appropriate fire rated
smoke seal, having mitred cut joint (self tab/screwed assembled at site) and provided with appropriate
reinforcement suitable for taking hardware and flush fixing as per IS 4351. The smoke seal material shall be
of EPDM tested in accordane with ASTM E-84 of minimum size 10x 4mm, fixed within the inbuilt groove
or stuck with adhesive on the entire perimeter of the frame. The door frame shall be fixed to the three sides
to masonary wall opening with CSK/Hex headed fastner of minimum 8 mm dia size and minimum 80mm
long with 8mm dia Polyamide sleeves @ 5 numbers at each on vertical sides and 2 numbers on horizontal
top side_ Door shutter: The double skinned single leaf partially insulated fire rated door shutters shall be
consisting of minimum 50 mm thick and having box like structure, slots cut and holes punched, for fixing of
hardwares with stiffners as per IS: 16074 including resin bonded mineral wool / ceremic wool infill material
of minimum density 96 kg/cum. Door leaf shall be provided with vision panel, having maximum area of
0_06 sqm, of 120 minute fire rated minimum 6 mm thick clear borosilicate glass pane fixed with clip-on
arrangement and fire rated ceramic tape having minimum size 13x2 mm to be fixed all around the glass on
both the sides The intumescent seal of minimum size 15x1.5 mm or of size as per test evidence shall be
fixed on all the three edges of the door leaf. The door shutter shall be mounted on the frame with SS 304
grade ball bearing butt hinges as per EN 1935 : 2002 or butt hinges as per IS 12817, of minimum size
100x75x3 mm @ 5 numbers hinges upto 2400mm height or as per test evidence, whichever is more, fixed
with M6 25 screws. All doors shall be factory prepared for receiving appropriate hardware and provided
with necessary reinforcement for hardware accessories. Hardware Accessories: Fire doorset assembly shall
be provided with one number of Single point Panic push bar (cross bar) device of desired finish as per EN
1125 and one number external trim including half cylinder of 42mm long with one side key as per EN 1125.
One number heavy duty door closer of size EN 3-5 with standard arm, of desired finish (suitable upto 1250
mm door width) conforming to IS 3564/EN 1154. Finishing. Both frame and door shutters shall be factory
finished with polyester powder coating of minimum 50 microns thick and shall have passed salt spray test
as per IS:13871 of approved colour and shade all complete as per manufacturer's specifications and
as per direction of the Engineer-in-charge. installation. The hollow space in the door frame shall be filled /
injected with fire rated self extinguishing type polyurethane foam (PUF) after installation at site of work_
The rate shall be inclusive of complete fire rated door assembly, supply and installation by the approved
manufacturer
9.162E.1 Single leaf Partially Insulated metal fire rated doorset of FD 120 PI classification with 120 minutes
integrity and 30 minutes insulation as per IS 3614:2021 - For Staircase/ Exit pathway! Refuge area etc.
1 Approx 1 10 10
Total 10
Total (Rounded) 10.00 sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 10 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
34.1 9.162F.1 9.162F Providing and fixing factory made ISI marked partially insulated metal fire rated doorset assembly,
for staircase / exit pathway and refuge areas applications, consisting of galvanized iron steel frame and
double leaf shutter including necessary hardware accessories conforming to FD 120 PI classification of IS
3614 :2021 with fire rating of 120 minutes integrity and 30 minutes insulation. The door frame and shutter
shall be made out of minimum 1 20 mm thick GI Sheet with minimum 120 GSM Zinc coating as per IS:
277. The entire fire rated doorset assembly shall be tested in latched condition as per IS 17518 (Part -1):
2022 Frame The frame shall be of minimum size 90 x 60 mm with grooved profile to take appropriate fre
rated smoke seal, having mitred cut joint (self tab/screwed assembled at site) and provided with appropriate
reinforcement suitable for taking hardware and flush fixing as per IS 4351. The smoke seal material shall be
of EPDM tested in accordane with ASTM E-84 of minimum size 10 x 4mm, fixed within the inbuilt groove
or stuck with adhesive on the entire perimeter of the frame The door frame shall be fixed to the three sides
to masonary wall opening with CSK/Hex headed fastner of minimum 8 mm dia size and minimum 80mm
long hot dip galvanized with 8mm dia Polyamide sleeves @ 5 number at each on vertical sides and 3 number
on top side. Door shutter The double skinned double leaf partially insulated door shutters shall be consisting
of minimum 50 mm thickness and having box like structure, slots cut and holes punched. for fxing of
hardwares with stiffners as per IS: 16074 including resin bonded mineral wool / ceremic wool nfill material
of minimum density 96 kg/cum. Each door leaf shall be provided with vision panel, having maximum area of
0.06 sqm, of 120 minute fire rated minimum 6 mm thick clear borosilicate glass pane fixed with clip-on
arrangement and fire rated ceramic tape having minimum size 13x2 mm to be fixed all around the glass on
both the sides. The intumescent seal of minimum size 15x1,5 mm or of size as per test evidence shall be
fixed on all the three edges of the door leaves. Integral astragals to be provided for double leaf door on the
meeting style each on active and inactive leaf. The door shutters shall be mounted on the frame with SS 304
grade ball bearing butt hinges as per EN 1935 : 2002 or butt hinges as per IS 12817, of minimum size
100x75x3 mm @ 5 numbers hinges upto 2400mm height or as per test evidence, whichever is more, fixed
with M6 25 screws. All doors shall be factory prepared for receiving appropriate hardware and provided
with necessary reinforcement for hardware accessories. Accessories Hardware Fire doorset assembly shall be
provided with one number of single point panic push bar (cross bar) for active leaf and one number double
point panic push bar (cross bar) with bottom strike of desired finish with verticle shoot bolts on top and
bottom for inacitvie leaf of double leaf door as per EN 1125, one number external trim with half cylinder 42
mm long with one side key as per EN 1125, two number heavy duty door closers of size EN 3-5 with
standard arm with of desired finish (suitable for 1250 mm wide door leaf) conforming to IS 3564 / EN 1154,
and one number surface mounted door coordinator for sequencing of closing. Finishing: Both frame and
door shutters shall be factory finished with polyester powder coating of minimum 50 microns thick and shall
have passed salt spray test as per IS:13871 of approved colour and shade all complete as per
manufacturer's specifications and as per direction of the Engineer-in-charge. Installation: The hollow space
in the door frame shall be filled / injected with fire rated self extinguishing type polyurethane foam (PUF)
after installation at site of work. The rate shall be inclusive of complete fire rated door assembly, supply and
installation by the approved manufacturer.
9.162F.1 Double leaf partially Insulated metal fire rated doorset of PD 120 PI classification with 120
minutes integrity and 30 minutes insulation as per IS 3614:2021 for Staircase/ Exit pathway / Refuge area
etc
1 Approx 1 10 10
Total 10
Total (Rounded) 10.00 sqm
35.1 9.165.2 9.165 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with
necessary screws etc all complete.
9.165.2 100mm
1 Approx 1 50 50
Total 50
Total (Rounded) 50.00 each
36 10.2 10.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including
cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
1 Approx. 1 500 500
Total 500
Total (Rounded) 500.00 kg

/2025 JAN 24 AR & MO WORK FOR AMC Page 11 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
37.1 10.16.1 10.16 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including
cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding
and bolted with special shaped washers etc. complete.
10.16.1 Hot finished welded type tubes
1 Approx. 1 2500 2500
Total 2500
Total (Rounded) 2,500.00 kg
38.1 10.27.1 10.27 Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia
double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia
polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of
Engineer-in-charge.
10.27.1 10 x 60 mm
1 Approx 1 50 50
Total 50
Total (Rounded) 50.00 each
38.2 10.27.2 10.27 Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia
double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia
polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of
Engineer-in-charge.
10.27.2 10 x 80 mm
1 Approx 1 50 50
Total 50
Total (Rounded) 50.00 each
38.3 10.27.3 10.27 Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia
double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia
polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of
Engineer-in-charge.
10.27.3 10 x 120 mm
1 Approx 1 50 50
Total 50
Total (Rounded) 50.00 each
39.1 10.29.1 10.29 Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3
mm and nuts & bolts complete.
10.29.1 Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides
1 Approx 1 50 50
Total 50
Total (Rounded) 50.00 sqm
39.2 10.29.2 10.29 Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3
mm and nuts & bolts complete.
10.29.2 Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides
1 Approx 1 50 50
Total 50
Total (Rounded) 50.00 sqm
41.1 11.26.1 11.26 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement
slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with
base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :
11.26.1 25 mm thick
1 Approx 1 30 30
Total 30
Total (Rounded) 30.00 sqm
42 11.27 11.27 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average)
thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment
to match the shade of the slabs, including rubbing and polishing complete.
1 Approx 1 20 20

/2025 JAN 24 AR & MO WORK FOR AMC Page 12 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
Total 20
Total (Rounded) 20.00 sqm
43.1 11.41.2 11.41 Providing and laying vitrified floor tiles in diferent sizes (thickness to be specified by the
manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all
colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey
cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc.,
complete.
11.41.2 Size of Tile 600x600 mm
1 Approx. 1 250 250
Total 250
Total (Rounded) 250.00 sqm
45.1 11.56.1 11.56 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well
as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone
slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with
cement slurry and pointing with white cement slurry admixed with pigment of matching shade including
rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.
11.56.1 Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent
1 Approx 1 30 30
Total 30
Total (Rounded) 30.00 sqm

46.1 12.45.1 12.45 Providing and fixing false ceiling at all heights including providing and fixing of frame work made of
special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both
side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges
of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5
mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50
mm of required length with nuts & bolts of required size and other end of angle hanger fixed with
intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the
ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5
mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with
connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing
perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of
ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws
@ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help
of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of
tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with
jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable
for board, all as per manufacturer's specification and also including the cost of making openings for light
fittings, grills, difusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per
drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :
12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with
BIS certification marks)
1 Approx. 1 1000 1000
Total 1000
Total (Rounded) 1,000.00 sqm
47 12.50 12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as
approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm
thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240
mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns.
Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and
should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be
fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch
in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including
cutting to size and shape wherever required.
1 Approx 1 300 300
Total 300
Total (Rounded) 300.00 sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 13 of 36

SNo Item No Description Number Length Breadth Height Weight Qty

48.1 12.51.1 12.51 Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness
0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc
coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of
the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
12.51.1 Ridges plain (500- 600mm)
1 Approx 1 20 20
Total 20
Total (Rounded) 20.00 metre
48.2 12.51.2 12.51 Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness
0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc
coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of
the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
12.51.2 Flashings/ Aprons.( Upto 600 mm)
1 Approx 1 40 40
Total 40
Total (Rounded) 40.00 metre

48.3 12.51.6 12.51 Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness
0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc
coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of
the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
12.51.6 Gutter (600 mm over all girth)
1 Approx 1 20 20
Total 20
Total (Rounded) 20.00 metre
49.1 12.52.3 12.52 Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true
horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized
@ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get
required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm
center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long
spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross
"T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at
middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and
laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for
services like difusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended
from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50
mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8
mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections
shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as
directed by Engineer-in-charge.
12.52.3 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of
Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white
0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side
with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to
the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.
1 Approx. 1 500 500
Total 500
Total (Rounded) 500.00 sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 14 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
49.2 12.52.4 12.52 Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true
horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized
@ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get
required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm
center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long
spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross
"T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at
middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and
laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for
services like difusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended
from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50
mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8
mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections
shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as
directed by Engineer-in-charge.
12.52.4 12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre
conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with
center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side,
having an NRC (Noise Reduction Coeficient) of 0.79
1 Approx. 1 1000 1000
Total 1000
Total (Rounded) 1,000.00 sqm

50 12.53 12.53 Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate
false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter
locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both
side) consisting of main 'T' runner suitably spaced at joints to get required length and of size 24x38 mm
made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross "T" of size 24x28
mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main'T' at 600 mm centre to
centre to form a grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24 x28 mm made
of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of
size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of
size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre
to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges
calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services
like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main 'T' runners to be
suspended from ceiling using al. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and
50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8
mm, spaced at 1200 mm centre to centre along main 'T'. Bottom exposed with 24 mm of all T-sections shall
be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by
Engineer-in-Charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No
deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium
silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection >85%, non- combustible as per
B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.
1 Approx. 1 500 500
Total 500
Total (Rounded) 500.00 sqm
51.1 13.1.1 13.1 12 mm cement plaster of mix:
13.1.1 1:4(1 cement: 4 fine sand)
1 NCI Back side STP 1 370 0.83 2 614.2
Total 614.2
Total (Rounded) 614.20 sqm
52.1 13.2.1 13.2 15 mm cement plaster on the rough side of single or half brick wall of mix:
13.2.1 1:4(1 cement: 4 fine sand)
1 Approx 1 300 300
Total 300
Total (Rounded) 300.00 sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 15 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
53.1 13.3.1 13.3 20 mm cement plaster of mix:
13.3.1 1:4(1 cement: 4 fine sand)
1 Approx 1 100 100
Total 100
Total (Rounded) 100.00 sqm
54.1 13.16.1 13.16 6 mm cement plaster of mix:
13.16.1 1:3(1 cement :3 fine sand)
1 Approx 1 100 100
Total 100
Total (Rounded) 100.00 sqm
55.1 13.19.1 13.19 Rough cast plaster upto 10 m height above ground level with a mixture of sand and gravel or crushed
stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, under
layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1
cement: 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement.
13.19.1 Ordinary cement finish using ordinary cement
1 Approx 1 500 500
Total 500
Total (Rounded) 500.00 sqm
56.1 13.33.1 13.33 Pointing on stone work with cement mortar 1:3 (1 cement: 3 fine sand) :
13.33.1 Flush/ Ruled pointing
1 NCI Back side STP 1 100 100
Total 100
Total (Rounded) 100.00 sqm
57.1 13.44.1 13.44 Finishing walls with water proofing cement paint of required shade:
13.44.1 New work (Two or more coats applied @ 3.84 kg/10 sqm)
1 NCI Back side STP 1 370 6 2220
Total 2220
Total (Rounded) 2,220.00 sqm
59 13.72 13.72 Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers,
under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching
tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement
plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all
around as per approved pattern, including scrubbing and washing the top layer with brushes and water to
expose the stone chippings ,complete as per specification and direction of Engineer-in-charge (payment for
providing grooves shall be made separately).
1 Approx 1 500 500
Total 500
Total (Rounded) 500.00 sqm

60.1 13.73.1 13.73 Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern
using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of
panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge :
13.73.1 15 mm wide and 15 mm deep groove
1 Approx 1 500 500
Total 500
Total (Rounded) 500.00 metre
61.1 14.1.1 14.1 Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including
cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls
complete, including disposal of rubbish to the dumping ground, all complete as per direction of
Engineer-in-Charge.
14.1.1 With cement mortar 1:4 (1 cement : 4 fine sand)
1 Approx 1 200 200
Total 200
Total (Rounded) 200.00 sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 16 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
62 14.72 14.72 Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story
height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup &
lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding
for working platform etc. and maintaining it in a serviceable condition for the required duration as approved
and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with
the building etc wherever required for inspection of work at required locations with essential safety features
for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of
the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of
duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction
for scaffolding in the existing item to be done.
1 Approx. 1 1200 1200
Total 1200
Total (Rounded) 1,200.00 sqm
63.1 14.89.1 14.89 Providing and fixing APP (Atactic Polypropylene Polymer) modified prefabricated five layer 2
mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of
bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrance manufacture of density at
25°C, 0.87 - 0.89 kg/ litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be
laid using Butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and
chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse
direction at 23°C as 350/300 N/ 5 cm. Tear strength in longitudinal and transverse direction as 60/80N.
Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in
accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised
applicator of the manufacture of membrane.
14.89.1 2 mm (for corrugated roof sheets)
1 Approx. 1 500 500
Total 500
Total (Rounded) 500.00 sqm
64 14.92 14.92 Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness
1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as
per manufactures recommendation.
1 Approx. 1 200 200
Total 200
Total (Rounded) 200.00 sqm
65.1 15.2.1 15.2 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50
metres lead as per direction of Engineer - in - charge.
15.2.1 Nominal concrete 1:3:6 or richer mix (including equivalent design mix)
1 Approx 1 10 10
Total 10
Total (Rounded) 10.00 cum
66.1 15.7.4 15.7 Demolishing brick work manually/ by mechanical means including stacking of serviceable material
and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.
15.7.4 In cement mortar
1 Approx 1 10 10
Total 10
Total (Rounded) 10.00 cum
67.1 15.12.1 15.12 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats,
architrave, holdfasts etc. complete and stacking within 50 metres lead :
15.12.1 Of area 3 sq. metres and below
1 Approx 1 10 10
Total 10
Total (Rounded) 10.00 each
68.1 15.13.1 15.13 Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within
50 metres lead :
15.13.1 Of area 3 sq. metres and below
1 Approx 1 10 10

/2025 JAN 24 AR & MO WORK FOR AMC Page 17 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
Total 10
Total (Rounded) 10.00 each
69.1 15.17.1 15.17 Dismantling steel work in single sections including dismembering and stacking within 50 metres lead
in:
15.17.1 R.S. Joists
1 Approx 1 200 200
Total 200
Total (Rounded) 200.00 kg
69.2 15.17.2 15.17 Dismantling steel work in single sections including dismembering and stacking within 50 metres lead
in:
15.17.2 Channels, angles, tees and flats
1 Approx 1 200 200
Total 200
Total (Rounded) 200.00 kg
70 15.18 15.18 Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset
plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.
1 Approx 1 500 500
Total 500
Total (Rounded) 500.00 kg
71 15.19 15.19 Dismantling steel work manually/ by mechanical means in built up sections without dismembering and
stacking within 50 metres lead as per direction of Engineer-in-charge.
1 Approx 1 500 500
Total 500
Total (Rounded) 500.00 kg
72.1 15.23.1 15.23 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50
metres lead.
15.23.1 For thickness of tiles 10 mm to 25 mm
1 Approx 1 100 100
Total 100
Total (Rounded) 100.00 sqm

73 15.25 15.25 Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and
disposal of unserviceable material within 50 metres lead.
1 Approx 1 50 50
Total 50
Total (Rounded) 50.00 sqm
74.1 15.28.1 15.28 Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50
metres lead of :
15.28.1 G.S. Sheet
1 Approx 1 100 100
Total 100
Total (Rounded) 100.00 sqm
75.1 15.34.1 15.34 Dismantling and stacking within 50 metres lead, fencing posts or struts including all earth work and
dismantling of concrete etc. in base of :
15.34.1 T’ or ‘L’ iron or pipe
1 Approx 1 200 200
Total 200
Total (Rounded) 200.00 each
76 15.36 15.36 Dismantling barbed wire or flexible wire rope in fencing including making rolls and stacking within 50
metres lead.
1 Approx 1 50 50
Total 50
Total (Rounded) 50.00 kg

/2025 JAN 24 AR & MO WORK FOR AMC Page 18 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
77.1 16.3.9 16.3 Supplying and stacking at site.
16.3.9 Good earth
1 NCI Back side STP 1 370 4.01 0.45 667.66
2 Approx 1 332.34 332.34
Total 1000
Total (Rounded) 1,000.00 cum
78 16.11 16.11 Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete.
1 NCI Back side STP 1 100 100
Total 100
Total (Rounded) 100.00 sqm
79.1 16.13.1 16.13 Cutting road and making good the same including supply of extra quantities of materials i.e.
aggregate, moorum screening, red bajri and labour required.
16.13.1 Bituminous portion
1 Approx 1 10 10
Total 10
Total (Rounded) 10.00 cum
80.1 16.18.1 16.18 Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every
15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only
and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire
weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn
buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately).
Payment to be made per metre cost of total length of barbed wire used.
16.18.1 With G.I. barbed wire
1 Approx 1 100 100
Total 100
Total (Rounded) 100.00 metre
81 16.53 16.53 Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre
openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with
existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed
wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed
wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed
tape(R.B.T.) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq. mm with tape (0.52 mm
thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)
1 Approx. 1 300 300
Total 300
Total (Rounded) 300.00 metre
82 16.68 16.68 Providing and laying 60 mm thick faciory made cement concrete interlocking paver block of M
-30 grade made by block making machine with strong vibratory compaction, of approved size, design &
shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand,
filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.
1 Approx. 1 2000 2000
Total 2000
Total (Rounded) 2,000.00 sqm
83 16.69 16.69 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete
in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse
sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to
more than 5 mm), including making drainage opening wherever required complete etc. as per direction of
Engineer- in-charge (length of finished kerb edging shall be measured to calculate volume for payment).
(Precast C.C. kerb stone shall be approved by Engineer-in-charge).
1 Approx. 1 440 0.3 0.15 19.8
Total 19.8
Total (Rounded) 19.80 cum

/2025 JAN 24 AR & MO WORK FOR AMC Page 19 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
84.1 16.86.1 16.86 Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished
machine cut granite stone of required size and shape of approved shade, colour and texture in footpath,
flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath,
flooring in road side plazas and similar locations, laid over 20 mm thick base of cement mortar 1:4 (1cement
: 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch
ups etc. complete as per direction of Engineer-in-Charge.
16.86.1 With granite stone of area less than 0.50 sqm.
1 Approx. 1 120 120
Total 120
Total (Rounded) 120.00 sqm
85.1 18.6.9 18.6 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801
UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply,
including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling &
testing of joints complete as per direction of Engineer-in-Charge. External work
18.6.9 PN - 10 Pipe, 110 mm OD (SDR-11)
1 Approx. 1 24 24
Total 24
Total (Rounded) 24.00 metre
86 18.48 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701
marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and
overflow pipes but without fittings and the base support for tank.
1 Approx. 6 10000 60000
Total 60000
Total (Rounded) 60,000.00 per
litre
87.1 18.70.1 18.70 Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including
testing of joints and the cost of rubber gasket :
18.70.1 100 mm dia pipes
1 Approx. 1 24 24
Total 24
Total (Rounded) 24.00 joint
87.2 18.70.2 18.70 Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including
testing of joints and the cost of rubber gasket :
18.70.2 150 mm dia pipes
1 Approx. 1 24 24
Total 24
Total (Rounded) 24.00 joint
88.1 18.86.1 18.86 Providing and fixing Stainless Steel pipe and fitting of grade AISI 304 as per JIS standard 3448
complete with press type fitting (fitting shall be paid for separately) including fixing of the pipe with clamps
at 1.00m spacing and also including cutting of chases and making good the walls including testing of joints
complete as per direction of Engineer -in-charge. (The pipe length inserted in the fitting shall not be
measured for payment) Internal work - Concealed Pipe
18.86.1 15.88 mm outer dia Pipe.
1 Approx. 1 30 30
Total 30
Total (Rounded) 30.00 metre
89.1 18.87.1 18.87 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Coupling/Socket
18.87.1 For 15.88 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each

/2025 JAN 24 AR & MO WORK FOR AMC Page 20 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
89.2 18.87.3 18.87 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Coupling/Socket
18.87.3 For 28.58 mm outer dia pipe
1 Approx. 1 20 20
Total 20
Total (Rounded) 20.00 each
89.3 18.87.4 18.87 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Coupling/Socket
18.87.4 For 34.00 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
89.4 18.87.5 18.87 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Coupling/Socket
18.87.5 For 42.70 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
90.1 18.88.1 18.88 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to
JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per dirction of Engineer-in-charge. Reducer
18.88.1 For 22.22 mm x 15.88 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
91.1 18.89.1 18.89 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Slip Coupling/ Socket
18.89.1 For 15.88 mm outer dia pipe
1 Approx. 1 20 20
Total 20
Total (Rounded) 20.00 each
91.2 18.89.3 18.89 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Slip Coupling/ Socket
18.89.3 For 28.58 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
91.3 18.89.4 18.89 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Slip Coupling/ Socket
18.89.4 For 34.00 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each

/2025 JAN 24 AR & MO WORK FOR AMC Page 21 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
91.4 18.89.5 18.89 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Slip Coupling/ Socket
18.89.5 For 42.70 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
92.1 18.90.1 18.90 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Elbow 90°
18.90.1 For 15.88 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
92.2 18.90.3 18.90 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Elbow 90°
18.90.3 For 28.58 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
92.3 18.90.4 18.90 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Elbow 90°
18.90.4 For 34.00 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
92.4 18.90.5 18.90 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Elbow 90°
18.90.5 For 42.70 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each

93.1 18.91.1 18.91 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Reducing Elbow 90°
18.91.1 For22.22 mm x 15.88 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
94.1 18.92.1 18.92 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Equal Tee
18.92.1 For 15.88 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
94.2 18.92.3 18.92 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Equal Tee
18.92.3 For 28.58 mm outer dia pipe
1 Approx. 1 15 15

/2025 JAN 24 AR & MO WORK FOR AMC Page 22 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
Total 15
Total (Rounded) 15.00 each
94.3 18.92.4 18.92 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Equal Tee
18.92.4 For 34.00 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
94.4 18.92.5 18.92 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Equal Tee
18.92.5 For 42.70 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
95.1 18.93.1 18.93 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Reducing Tee
18.93.1 For 22.22 mm x 15.88 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
96.1 18.94.1 18.94 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Male Thread Tee
18.94.1 For 15.88 mm outer dia x 15 mm nominal dia threaded
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
97.1 18.95.1 18.95 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Female Thread Tee
18.95.1 For 15.88 mm outer dia x15 mm nominal dia threaded
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
98.1 18.96.1 18.96 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Female Thread Connector/ Adapter
18.96.1 For 15.88 mm outer dia x 15 mm nominal dia threaded
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
99.1 18.97.1 18.97 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Male Thread Connector/ Adapter
18.97.1 For 15.88 mm outer dia x 15 mm nominal dia threaded
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each

/2025 JAN 24 AR & MO WORK FOR AMC Page 23 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
100.1 18.98.1 18.98 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Valve Connector
18.98.1 For 15.88 mm outer dia x 15 mm nominal dia threaded
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
101.1 18.99.1 18.99 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Female Threaded Elbow 90°
18.99.1 For 15.88 mm outer dia x 15 mm nominal dia threaded
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
102.1 18.100.1 18.100 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Male Threaded Elbow 90°
18.100.1 For 15.88 mm outer dia x 15 mm nominal dia threaded
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
103.1 18.101.1 18.101 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Cap
18.101.1 For 15.88 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
104.1 18.102.1 18.102 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming
to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of
required dia as per direction of Engineer-in-charge. Pipe Bridge
18.102.1 For 15.88 mm outer dia pipe
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each

105.1 18.103.1 18.103 Providing and fixing required Stainless Steel Fitting of press fit design of grade 316L as per IS :
6911:2017 and conforming to EN-10312 standard with V-profile and with O-ring sealing gasket of EPDM
material of required dia as per direction of Engineer-in-charge. Male Union
18.103.1 For 15 mm outer dia X 1/2” nominal dia threaded
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
106.1 19.17.1 19.17 Replacement of M.S. foot rests in manholes including dismantling concrete blocks and fixing with
20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm
nominal size):
19.17.1 With 20x20 mm square bar
1 Approx. 1 25 25
Total 25
Total (Rounded) 25.00 each
107.1 19.18.1 19.18 Supplying and fixing C.I. cover without frame for manholes :
19.18.1 455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg
1 Approx. 1 25 25
Total 25
Total (Rounded) 25.00 each

/2025 JAN 24 AR & MO WORK FOR AMC Page 24 of 36

SNo Item No Description Number Length Breadth Height Weight Qty

108.1.1 19.19.1.1 19.19 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and
approved quality
19.19.1 L D- 2.5
19.19.1.1 Rectangular shape 600x450 mm internal dimensions
1 Approx. 1 25 25
Total 25
Total (Rounded) 25.00 each
108.1.2 19.19.1.3 19.19 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and
approved quality
19.19.1 L D- 2.5
19.19.1.3 Circular shape 450 mm internal diameter
1 Approx. 1 15 15
Total 15
Total (Rounded) 15.00 each
109.1 19.21.2 19.21 Making connection of drain or sewer line with existing manhole including breaking into and making
good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate
20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand),
finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :
19.21.2 For pipes 250 to 300 mm diameter
1 Approx. 1 4 4
Total 4
Total (Rounded) 4.00 each
109.2 19.21.3 19.21 Making connection of drain or sewer line with existing manhole including breaking into and making
good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate
20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand),
finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :
19.21.3 For pipes 350 to 450 mm diameter
1 Approx. 1 4 4
Total 4
Total (Rounded) 4.00 each
110.1 19.36.1 19.36 Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C. pipes including collars/spigot
jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing
of joints etc. complete
19.36.1 450 mm dia RCC pipes.
1 Approx. 15 3 45
Total 45
Total (Rounded) 45.00 metre
111.1.1 21.1.1.2 21.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built
up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:
733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps
at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium
sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including
cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete
as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners
to be paid for separately) :
21.1.1 For fixed portion
21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron)
1 Approx. 1 300 300
Total 300
Total (Rounded) 300.00 kg

/2025 JAN 24 AR & MO WORK FOR AMC Page 25 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
111.2.1 21.1.2.2 21.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built
up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:
733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps
at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium
sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including
cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete
as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners
to be paid for separately) :
21.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and
making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene
gasket required (Fittings shall be paid for separately)
21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron)
1 Approx. 1 100 100
Total 100
Total (Rounded) 100.00 kg
112.1 21.2.2 21.2 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood
particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows
shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural
drawings and directions of engineer-in-charge.
21.2.2 Pre-laminated particle board with decorative lamination on both sides
1 Approx. 1 50 50
Total 50
Total (Rounded) 50.00 sqm
113.1 21.3.2 21.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with
EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of
engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):
21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
1 Approx. 1 50 50
Total 50
Total (Rounded) 50.00 sqm
114.1 21.4.1 21.4 Providing and fixing double action hydraulic floor spring of approved brand and manufacture
conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and
door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and
making good the same matching to the existing floor finishing and cover plates with brass pivot and single
piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer- in-charge.
21.4.1 With stainless steel cover plate minimum 1.25 mm thickness
1 Approx. 1 30 30
Total 30
Total (Rounded) 30.00 each
115.1 21.11.2 21.11 Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved
quality with necessary stainless steel screws etc. to the side hung windows as per direction of
Engineer-in-charge complete.
21.11.2 255 X 19 mm
1 Approx. 1 80 80
Total 80
Total (Rounded) 80.00 each
116.1 21.19.1 21.19 Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/
Ceramic/ Gypsum work by providing weather/ structural non sag elastomeric PU sealant over backer rod of
approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to
ASTM C920, DIN 18540-F & ISO 11600
21.19.1 Upto 5 mm depth and 5 mm width
1 Approx. 1 500 500
Total 500
Total (Rounded) 500.00 metre

/2025 JAN 24 AR & MO WORK FOR AMC Page 26 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
116.2 21.19.2 21.19 Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/
Ceramic/ Gypsum work by providing weather/ structural non sag elastomeric PU sealant over backer rod of
approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to
ASTM C920, DIN 18540-F & ISO 11600
21.19.2 Upto 10 mm depth and 10 mm width
1 Approx. 1 500 500
Total 500
Total (Rounded) 500.00 metre
116.3 21.19.3 21.19 Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/
Ceramic/ Gypsum work by providing weather/ structural non sag elastomeric PU sealant over backer rod of
approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to
ASTM C920, DIN 18540-F & ISO 11600
21.19.3 Upto 20 mm depth and 20 mm width
1 Approx. 1 500 500
Total 500
Total (Rounded) 500.00 metre
117 23.5 23.5 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in
the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
1 Approx. 1 20 20
Total 20
Total (Rounded) 20.00 cum

/2025 JAN 24 AR & MO WORK FOR AMC Page 27 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
118 25.2 25.2 Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system
of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all
heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the
specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times
design wind pressure without any failure), including functional design of the aluminum sections for fixing
glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws,
toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-
cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage
and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised
/ Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3
Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the
RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/
bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316,
of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural
silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of
required bite size in a clean and controlled factory / work shop environment, including double sided spacer
tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved
sealant design, within and all around the perimeter for holding glass. (d) Providing and fixing in position
flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site
conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make
it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to
make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at
bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This
item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid,
installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling
temporary structures and services, cranes or cradles etc. as described above and as specified. The item
includes the cost of getting all the structural and functional design including shop drawings checked by a
structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups
at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on
the assembled working structural glazing as specified, cleaning and protection till the handing over of the
building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all
the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item
description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge.
Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section
capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be
paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the
actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm.
up to two decimal places. Note:-2. The following performance test are to be conducted on structural
glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by
NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science &
Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the
necessity of testing on the basis of cost of the work, cost of the test and importance of the work.
Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or any
other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per
ISO/IEC 17025 1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to
+300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr 2. Static Water
Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml. 3.
Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto
2000 ml 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times
design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm 5.
Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test, Tests to
be conducted on site. 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto
2000 ml
1 Approx. 1 100 100
Total 100
Total (Rounded) 100.00 sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 28 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
119 25.3 25.3 Providing, assembling and supplying vision glass panels (IGUs) comprising of
hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as
required and specified, comprising of an outer heat strengthened float glass 6 mm thick, of approved colour
and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat
strengthned clear float glass 6 mm thick, spacer tube 12 mm wide, dessicants, including primary seal and
secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the
Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-
in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing
of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of
glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant)
provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6 mm thick substrate
with reflective soft coating on face # 2, + 12 mm Airgap + 6 mm Heat Strengthened clear Glass of approved
make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to
15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2
degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per
the site requirement.
1 Approx. 1 100 100
Total 100
Total (Rounded) 100.00 sqm
120 25.4 25.4 Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site
all accessories and hardwares for the openable panels as specified and of the approved make such as heavy
duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles,
buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per
the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-
in-Charge.
1 Approx. 1 25 25
Total 25
Total (Rounded) 25.00 sqm
121.1 26.35.3 26.35 Providing and injecting approved grout in proportion recommended by the manufacturer into
cracks/honey-comb area of concrete/masonry by suitable gun/pump at required pressure including cutting of
nipples after curing etc. complete as per directions of Engineer-in-Charge. (The payment shall be made on
the basis of actual weight of approved grout injected.)
26.35.3 Epoxy injection grout in concrete/RCC work of approved make
1 Approx. 1 200 200
Total 200
Total (Rounded) 200.00 kg
122 50.501 50.501 Providing and fixing signages of required size and shape made of 1.00 mm thick stainless steel sheet
including engraving and painting in enamel paint of letters and indication etc as per site requirement with
necessary brass screw & gitty / hanging brackets whichever is required etc. all complete as per the direction
of EIC.
1 Approx. 1 5 30 10 1500
Total 1500
Total (Rounded) 1,500.00 Sqcm
123 50.502 50.502 Providing and Fixing 1mm thick Stainless steel (Grade 304). with brass coating single side including
engraving and painting in enamel paint of letters and indication etc as per site requirement with necessary
brass screw & gitty / hanging brackets whichever is required etc. all complete as per the direction of EIC.
1 Approx. 1 14 30 12 5040
2 1 1
Total 5041
Total (Rounded) 5,041.00 Sqcm
124 50.503 50.503 Job work for repairing and refixing of HDPE & PPR Pipe Line of 110 mm Dia. with Tee joint
including HDPE Pipe Pe100 DN110 PN08, HDPE Tee, Elbow, Reducer, DN110, HDPE Long Neck Pipe
End DN110, MS Flange BS 10 Table D DN110, Gaskit, Nut Bolt Washer, Hiring Machine, Excavation of
Earth and other labour charges etc. all complete as per site requirement and direction of EIC.
1 Approx. 1 20 20

/2025 JAN 24 AR & MO WORK FOR AMC Page 29 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
Total 20
Total (Rounded) 20.00 Each
Job
125 50.504 50.504 Job work for repairing and refixing of HDPE & PPR Pipe Line of 160 mm Dia. with Tee joint
including HDPE Pipe Pe100 DN160 PN10, HDPE Tee, Elbow, Reducer, DN160, HDPE Long Neck Pipe
End DN160, MS Flange BS 10 Table D DN160, Gaskit, Nut Bolt Washer, Hiring Machine, Excavation of
Earth and other labour charges etc. all complete as per site requirement and direction of EIC.
1 Approx. 1 10 10
Total 10
Total (Rounded) 10.00 Each
Job
126 50.505 50.505 Job work for repairing and refixing of HDPE & PPR Pipe without Tee joint including HDPE Socket,
Elbow ,Hiring Machine,Excavation of Earth and other labour charges etc. all complete as per site
requirement and direction of EIC.
1 Approx. 1 20 20
Total 20
Total (Rounded) 20.00 Each
Job
127 50.506 50.506 Replacement of worn out and damaged 12.5 mm thick tapered edge gypsum plain board conforming
to IS 2095- (part -1) 2011 (bard with BIS Certification marks) including repair and re-fixing of existing
frame of gypsum false ceiling by providing horizontal member / vertical suspenders, G.I wire, channel,
angle, nut & bolts, connecting clips, soffit cleat, all drive screw, hold fastener, and finishing to a flush finish
of tapered and square edges of the board by joint filler/ finisher/ tape roll, two coats of primer suitable for
board, all as per manufacturer's specification and also including the cost of making openings for light
fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per
requirement, specification and direction of the Engineer in Charge. ( Make :- Gyoroc , Saint Gobain, Hilux,
USG Boral)
1 Approx. 1 100 100
Total 100
Total (Rounded) 100.00 Sqm
128 50.507 50.507 Replacement of worn out and damaged 15 mm thick densified tegular edged eco friendly light weight
calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level,
including repair and re-fixing of existing frame of false ceiling by providing horizontal member / vertical
suspenders, G.I wire, channel, angle, nut & bolts, connecting clips, soffit cleat, all drive screw, hold fastener
and also including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke
detectors etc. wherever required etc. all complete as per requirement, specification and direction of the
Engineer in Charge. ( Make :- Gyoroc , Saint Gobain, Hilux, USG Boral)
1 Approx. 1 100 100
Total 100
Total (Rounded) 100.00 Sqm
129 50.508 50.508 Replacement of worn out and damaged 12.5mm thick square edge PVC Laminated Gypsum Tile of
size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I
and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized
polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps
the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a
completely sealed Unit including repair and re-fixing of existing frame of false ceiling by providing
horizontal member / vertical suspenders, G.I wire, channel, angle, nut & bolts, connecting clips, soffit cleat,
all drive screw, hold fastener and also including, cutting/ making opening for services like diffusers, grills,
light fittings, fixtures, smoke detectors etc. wherever required etc. all complete as per requirement,
specification and direction of the Engineer in Charge.( Make :- Gyoroc , Saint Gobain, Hilux, USG Boral)
1 Approx. 1 100 100
Total 100
Total (Rounded) 100.00 Sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 30 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
130 50.509 50.509 Replacement of worn out and damaged 12.5 mm thick fully Perforated Gypsum Board tile made
from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation
of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30mm, backed with non
woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin
bonded glass wool backing including repair and re-fixing of existing frame of false ceiling by providing
horizontal member / vertical suspenders, G.I wire, channel, angle, nut & bolts, connecting clips, soffit cleat,
all drive screw, hold fastener and also including, cutting/ making opening for services like diffusers, grills,
light fittings, fixtures, smoke detectors etc. wherever required etc. all complete as per requirement,
specification and direction of the Engineer in Charge. ( Make :- Gyoroc , Saint Gobain, Hilux, USG Boral)
1 Approx. 1 100 100
Total 100
Total (Rounded) 100.00 Sqm
131 50.510 50.510 Replacement of worn out and damaged 8 mm thick calcium silicate board made with Calcareous &
Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable
crystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of
size 595x595 mm, having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick rock wool of 48
kg /cum backing. including repair and re-fixing of existing frame of false ceiling by providing horizontal
member / vertical suspenders, G.I wire, channel, angle, nut & bolts, connecting clips, soffit cleat, all drive
screw, hold fastener and also including, cutting/ making opening for services like diffusers, grills, light
fittings, fixtures, smoke detectors etc. wherever required etc. all complete as per requirement, specification
and direction of the Engineer in Charge. ( Make :- Gyoroc , Saint Gobain, Hilux, USG Boral)
1 Approx. 1 100 100
Total 100
Total (Rounded) 100.00 Sqm
132 50.511 50.511 Job work for running JCB along with Driver and fuel etc all complete as per the direction of EIC.
1 Approx. 1 100 100
Total 100
Total (Rounded) 100.00 Per
Hour
133 50.512 50.512 Designing, Fabrication and Installation of transparent Acrylic sheet for informative display/notice
signages for hanging with roof /celling or stud for fixing on wall surface of required size & shap with the
provision of two layers transparent acrylic sheet of 3mm and 8mm thick with multicolor double digital
printing for for matter/picture on one sheet i/c laser machine cut hole including Hanging brackets/ Stainless
steel arrangement ( 6mm dia. Stainless steel rod ) or Stud for fixing on wall surface where ever is required
for fixing the signages board on all surface etc. all complete as per site requirement and sample approved by
EIC. (Make for acrylic sheet: - Euro Plast, Astariglas)
1 Approx. 1 30000 30000
Total 30000
Total (Rounded) 30,000.00 Sqcm
134 50.513 50.513 Designing, Fabrication and Installation of transparent Acrylic sheet for informative display/notice
signages for Hanging with roof /ceiling or Stud for fixing on wall surface of required size & shape with the
provision of two layers transparent acrylic sheet of 3mm thick with multicolor Double digital printing for
matter/Picture on one sheet i/c Laser machine cutting, edging and polishing on all exposed edges and Laser
machine cut hole including Hanging brackets/ Stainless steel arrangement ( 6mm dia. Stainless steel rod ) or
Stud for fixing on wall surface where ever is required for fixing the signages board on all surface etc. all
complete as per site requirement and sample approved by EIC. (Make for acrylic sheet: - Euro Plast,
Astariglas)
1 Approx. 1 30000 30000
Total
Total (Rounded) Sqcm

/2025 JAN 24 AR & MO WORK FOR AMC Page 31 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
135 50.514 50.514 Designing, Fabrication and Installation of transparent Acrylic sheet for informative display/notice
signages for Hanging with roof /ceiling or Stud for fixing on wall surface of required size & shape with the
provision of two layers transparent acrylic sheet of 5-6mm thick with multicolor Double digital printing for
matter/Picture on two sheet i/c Laser machine cutting, edging and polishing on all exposed edges and Laser
machine cut hole including Hanging brackets/ Stainless steel arrangement ( 6mm dia. Stainless steel rod ) or
S.S L hanging signages bracket for fixing on wall surface where ever is required for fixing the signages
board on all surface and both sheet should be covered from the pariphery by the stainless steel/ aluminium U
channel etc. all complete as per site requirement and sample approved by EIC. (Make for acrylic sheet: -
Euro Plast, Astariglas)
1 Approx. 1 100000 100000
Total 100000
Total (Rounded) 100,000.00 Sqcm
136 50.515 50.515 Providing and fixing wooden batten of 100x20mm for hanging C.P Coat hook with iron screws, plugs
and priming coat on surface of 2nd class teak wood etc. all complete as per direction of Engineer in charge.
1 Approx. 1 30 30
Total 30
Total (Rounded) 30.00 Metre
137 50.516 50.516 Cutting holes by cutting machine up to 15 cm Dia in R.C.C. floors 15-30cm thickness and roofs for
passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1
cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to
make it leak proof etc. all complete as per the direction of EIC.
1 Approx. 1 5 5
Total 5
Total (Rounded) 5.00 Each
138 50.517 50.517 Removing of honey bee hives from the various height of buildings at NCI Hospital complex etc.
compete as per the direction of EIC.(Note: - All safety measure to be taken while removing the honey bee
hives from the outer side of building where accessibility is not available. including Bucket, Cloth for
cleaning honey bee, weight machine, Safety equipment, Ladder, Rope etc. all will be arranged by the
contractor.)
1 Approx. 1 50 50
Total 50
Total (Rounded) 50.00 Each

139 50.518 50.518 Credit for taking away of extracted honey from the bee hives etc complete as per the Direction of
EIC.
1 Approx. 1 50 2 100
Total 100
Total (Rounded) 100.00 Kg
140 50.519 50.519 Removing of wasp hives from the various height of buildings at NCI Hospital complex etc. compete
as per the direction of EIC. (Note: - All safety measure to be taken while removing the wasp hives from the
outer side of building where accessibility is not available. including Safety equipment, Ladder, Rope etc. all
will be arranged by the contractor.)
1 Hospital Complex 1 100 100
2 Residential Complex 1 100 100
Total 200
Total (Rounded) 200.00 Each
141 50.520 50.520 Removing and refixing Stainless steel new CYS lock set with both side operative key 60mm with
handles of Hardwyn make - saver series CYs Falcon size 200mm of approved quality as per manufacture
specification for 35 mm flush door, with necessary screws etc. all complete as per direction of Engineer- in
charge.
1 Approx. 1 20 20
Total 20
Total (Rounded) 20.00 Each
142 50.521 50.521 Providing and Fixing 10mm table top glass including edge moulding ect complete as per the
direction of EIC.(Make:-Saint Gobain , Modi )

/2025 JAN 24 AR & MO WORK FOR AMC Page 32 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
1 Approx. 1 10 1.5 0.75 11.25
Total 11.25
Total (Rounded) 11.25 Sqm
143 50.522 50.522 Providing and Fixing Sun Control film of 72% Sun light control of as per sample approved Quality in
the existing glass, panes of window and cleaning of glass etc. all complete as per the direction of EIC.
1 Approx. 1 20 1.6 1.6 51.2
2 -1 1.2 -1.2
Total 50
Total (Rounded) 50.00 Sqm
144 50.523 50.523 Providing and fixing self adhesive retro tape of double layer for signages with digital printing with
lemination over the sheet of required size i/c all types of letters and indications etc. all complete as per the
Direction of EIC.
1 Approx. 1 10 1.2 1.2 14.4
2 1 0.6 0.6
Total 15
Total (Rounded) 15.00 Sqm
145 50.524 50.524 Providing and Fixing Glow sign Board of reqd size with flex ( snow white ) including designing and
multicolour solvent printing of approved matter etc. all complete as per the direction of EIC.
1 Approx. 1 100 100
Total 100
Total (Rounded) 100.00 Sqm
146 50.525 50.525 Providing and fixing 75mm thick foam of sleep well or feather touch foam of density 40 in required
size and shape in seats etc. all complete i/c cutting and making good as per the Direction of EIC.
1 Approx. 10 1.2 0.46 5.52
Total 5.52
Total (Rounded) 5.52 Sqm
147 50.526 50.526 Providing and fixing leatherite sheet of Sheela, Talwar or National or equivalent make including
stitching as desired in required size and shape in quality back etc. all complete as per the Direction of EIC.
1 Approx. 10 1.3 1.01 13.13
Total 13.13
Total (Rounded) 13.13 Sqm
148 50.527 50.527 Job work for repair of 150mm /100 mm Dia. Ductile iron main water supply i/c Clamp, Mechanical
joint, Tie bars, loose collor , nut and bolt etc. all complete as per site requirement and direction of EIC.
1 Approx. 1 5 5
Total 5
Total (Rounded) 5.00 Each
Job
149 50.528 50.528 Providing and fixing roller blinds of approved colour shade and design i/c aluminium channel folding
and felting mechanism chains etc. complete at all elves as per direction of engineer in charge.(Vista make :
-Gray 004)
1 Approx. 1 10 1.6 1.6 25.6
Total 25.6
Total (Rounded) 25.60 Sqm
150 50.529 50.529 Providing & laying gang saw cut 18 mm thick, mirror polished, prepolished machine cut granite
stone of required size and shape of approved shade, color and texture over the S.S frame, floor with
Adhesive chemical etc. all complete as per the sample approved and direction of EIC. ( S white Granite
stone)
1 Approx. 1 30 30
Total 30
Total (Rounded) 30.00 Sqm

/2025 JAN 24 AR & MO WORK FOR AMC Page 33 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
151 50.530 50.530 Providing and fixing 3mm thick ACP (Aluminum Composite panel having 0.25mm thick aluminum
foil/sheet on both side) sheet over existing MS frame for signages base etc. as per requirement and fixing
with necessary self thread screw, rivets, tapes, plug and gitties, Hanging brackets where ever is required etc.
all completed as per direction of EIC.
1 Approx. 1 100 100
Total 100
Total (Rounded) 100.00 Sqm
152 50.531 50.531 Fabrication and placing/ fixing stainless steel ( Grade 304 ) S.S Table/ Setty/ barricade/ signages post
frames and railing post made of Hollow tube, channels, plates , chain link etc. including argon welding
,grinding, buffing , polishing and making curvature (wherever required) with necessary stainless steel nuts
and bolts etc. all complete as per direction of EIC. ( for payment purpose only weight of stainless steel
(Grade 304 members shall be considered .) (Make: Jindal S.S ltd, RINL) ( Note:- Argon welding will done
only)
1 Approx. 1 2500 2500
Total 2500
Total (Rounded) 2,500.00 Kg
153 50.532 50.532 Providing and filling the pot holes with ready mix specialized instantaneous road maintenance
bitumen concrete compound “Torch Tar or SHELMAC PR or Bitumax PR” or equivalent duly packed in
25Kg bag comprising necessary ingredients as per manufacturer’s specifications including laying ,
spreading and compacting ready mixed bitumen compound to specified location and area of any size and
also including loading and unloading , cleaning, removing of loose material and diversion of traffic etc.
complete & disposal of malba as per direction of Engineer-in-Charge.
1 Approx. 1 500 500
Total 500
Total (Rounded) 500.00 Kg
154 50.533 50.533 Providing and fixing 2.00mm thick powder coated aluminium sheet with coating of 60 to 65 mm
microns, compatible to bend at the angle of 90 degree of approved colour or shade (one or more colour in
combination )with suitable fixing arrangement /screws (screws should not be visible i.e to be covered under
layer of silicon or as directed by EIC) including cutting of aluminium sheet for electrical fittings, filling gaps
(5 mm to 25 mm )between adjoining aluminium sheets with silicon of approved colour and make etc. all
complete as per the dirtection of EIC.
1 Approx. 4 6 6 144
2 1 56 56
Total 200
Total (Rounded) 200.00 Sqm
155 50.534 50.534 Job work for repairing and refixing of damaged M.S door including M.S angle, plate, hinges, fastener
etc. for repairing of door stacking of useful material near the site and disposal of unserviceable material from
the site with all lead and lifts and repairing brick wall, plaster, putty, painting work etc. all complete as per
the requirement at site and the direction of EIC. (Note: - All safety measures to be taken while repairing and
refixing where accessibility is not available including ladder, rope, etc. all will be arranged by the
contractor.)
1 Approx. 1 5 5
Total 5
Total (Rounded) 5.00 Each
Job
156 50.535 50.535 Providing and fixing Push cock arrangement for existing hand free portable washbasin at various
location etc all complete as per the direction of EIC.
1 Approx. 1 12 2 24
Total 24
Total (Rounded) 24.00 Each
157 50.536 50.536 Providing and fixing GI wire arrangement alongwith Pedal for existing hand free portable washbasin
at various location etc all complete as per the direction of EIC.
1 Approx. 1 12 2 24
Total
Total (Rounded) Each

/2025 JAN 24 AR & MO WORK FOR AMC Page 34 of 36

SNo Item No Description Number Length Breadth Height Weight Qty

158 50.537 50.537 Clearing grass and removal of the rubbish up to a distance of 2 Km outside the periphery of the area
cleared.
1 NCI Back side STP 1 200 15 3000
Total 3000
Total (Rounded) 3,000.00 Sqm
159 50.538 50.538 Providing and fixing stainless steel ( Grade 304 ) S.S wall guard corner made by pressing S.S sheet
on molding machine including making hole buffing , polishing and making curvature (wherever required)
and fixing with necessary stainless steel stud, nuts and bolts etc. all complete as per direction of EIC. (For
payment purpose only weight of stainless steel (Grade 304 members shall be considered only.) (Make: Jindal
S.S ltd, RINL)
1 For lift corner 1 38 1.2 0.2 15.7 143.18
2 L.S 1 356.82 356.82
Total 500
Total (Rounded) 500.00 Kg
160 50.539 50.539 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/
suede finish with high density protective surface layer and reverse side of adhesive bonding quality
conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 0.80 mm thick
1 Approx. 1 100 100
Total 100
Total (Rounded) 100.00 Sqm
161 50.540 50.540 Providing and fixing ISI marked plywood of 18 mm thick in Almirahs, cupboards, table computer
tables, racks and setties etc with necessary nails screws and adhesive i/c the cost of wooden gola / beading of
size 18x3 mm / 40x5mm on cut / tape on exposed edges i/c polishing the gola/margin with french spirit
polish two or more coats complete as per the direction of engineer in charge.
1 Approx. 1 100 100
Total 100
Total (Rounded) 100.00 Sqm
162 50.541 50.541 Repairing and replacement of damage parts of Roca Urinal sensor R9T3020N060TW-
Sentronicurinal Solenoid valve W/O body including all applicable taxes, service charge, carriage etc. all
complete as per requirement and direction of EIC.
1 Appprox 1 150 150
Total 150
Total (Rounded) 150.00 Each
163 50.542 50.542 Repairing and replacement of damage parts of Roca Urinal sensor R9T1010N070ATW-
Sentncurinal- Solf valve PKG KIT30X30X5MM including all applicable taxes, service charge, carriage etc.
all complete as per requirement and direction of EIC.
1 Approx 1 150 150
Total 150
Total (Rounded) 150.00 Each
164 50.543 50.543 Repairing and replacement of damage parts of Roca Urinal sensor R9T3100N010ATW- Sentronic
urinal -Sensor unit including all applicable taxes, service charge, carriage etc. all complete as per
requirement and direction of EIC.
1 Approx 1 150 150
Total 150
Total (Rounded) 150.00 Each
165 50.544 50.544 Repairing and replacement of damage parts of Roca Urinal sensor R9T3010N000BTW- Sentronic
urinal DC- battery assembly including all applicable taxes, service charge, carriage etc. all complete as per
requirement and direction of EIC.
1 Approx 1 150 150
Total 150
Total (Rounded) 150.00 Each

/2025 JAN 24 AR & MO WORK FOR AMC Page 35 of 36

SNo Item No Description Number Length Breadth Height Weight Qty
166 50.545 50.545 Repairing and replacement of damage parts of Roca Urinal sensor R9TWSS02040N000B- Euret
front plate including all applicable taxes, service charge, carriage etc. all complete as per requirement and
direction of EIC. (Spare part will be paid separately)
1 Approx 1 150 150
Total 150
Total (Rounded) 150.00 Each

ER. DEEPAK YADAV (JE/C) ER. SUNIL KUMAR MEHRA (AE/C) ER. SUNIL KUMAR (EE/C)

/2025 JAN 24 AR & MO WORK FOR AMC Page 36 of 36