E: [email protected].

uk

RETURN TO HOMEPAGE

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE

SECTION S
SOIL

For the implementation of civil engineering structures, the

engineers must base their calculations according to the soil
properties.
This section analyses a soil sample to evaluate its charac-
teristics, by providing a complete range of testing equipment
for: sampling, preparation, classification, consolidation, shear
strength, triaxial, compaction, penetration, bearing capacity,
permeability, density, geotechnical and chemical tests, in
compliance with the EN, ASTM, BS and the most known Inter-
national Standards.

TECNOTEST
MATERIAL TESTING EQUIPMENT

In early 2017 Matest has acquired Tecnotest.

The famous elephant has always been appreciated from the
construction material industry for the quality and the stiffness
of its products, with a special focus on the geotechnical range.
We are happy to have Tecnotest now part of our group.

Tel: +44 (0) 1442 402770

 E: [email protected]

460 RETURN TO HOMEPAGE

SECTION S | SOIL

S050
LIGHTWEIGHT DYNAMIC PENETROMETER
STANDARD: DIN 4094
Used to establish the thickness of different strata, when testing
compaction works and to determine the relative density of fills and
naturally deposited non-cohesive soils.
In general if the ground is not too compact, penetration tests can be
carried of about 8 to 12 metres.
The penetrometer set, huosed in carrying case, consists of:
10 kg drop rammer, 500 mm fall and anvil,
11 sounding rod Ø 22 mm x 1 m lenght complete with threaded
collar and guiding rod
Grooved rod to extract samples
2 drive point 90°, 5 cm² and 10 cm² surface
Lifting device for sounding rod, accessories
Dimensions: 1080x360x220 mm
Weight: 72 kg approx

S051
DYNAMIC CONE PENETROMETER (DCP) S050
TRL = TRANSPORT RESEARCH LABORATORY, UK. S057
STANDARD: ASTM D 6951-03 FIELD INSPECTION POCKET VANE TESTER
This portable hand operated equipment is designed to obtain a STANDARD: ASTM D 2573
direct and rapid in-situ evaluation of the structural strength of road
Used to determine the shear strength of undrained (CU) cohesive
pavement layers constructed with unbound materials.
soft soils, to firm non-fissured soils on site.
The DPC Penetrometer results can be compared with CBR
The instrument consists of a T-handle cylindrical body where a
(California Bearing Ratio) as per sperimental Kleyn 1982 studies.
torsional spring is housed, and three interchangeable vanes of
The test is performed with continuous penetrations at approx.
different sizes, used depending to the expected strength of the soil
800 mm depth with max. depth of 2 m by using extension rods.
to be tested.
The equipment housed in carrying case, consists of:
The vane is inserted into the soil for 60 mm approx., and the max.
- Drop sliding hammer 8 kg weight, falling height of 575 mm
torque value is measured on a collar attached to the shaft.
- Impact anvil with driving rod
Measuring range: 0 - 240 kPa
- Penetration rod with conical 60° point and Ø 20 mm
The unit, all stainless steel made, is supplied calibrated with
- Bar wrench, spanners, accessories.
calibration certificate and conversion table and complete
Dimensions: 1210x340x190 mm with three vanes dimensions (diameter x height) 16x32, 20x40,
Weight: 29 kg approx 25.4x50.8 mm, extension rod 500 mm long, tools, carrying case.
Dimensions: 500x300x100 mm
ACCESSORIES | SPARE Weight: 4 kg approx.
S051-10 Drop Sliding Hammer 4.6 kg weight.
S051-12 Extension rod, 400 mm long ACCESSORY | SPARE
S051-11 Spare Penetration conical point 60°
S057-01 Extension rod, 500 mm long

S057

S051

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 461

SECTION S | SOIL

S051-01

S052KIT S051-01
SOIL PROSPECTING KIT MACKINTOSH PROSPECTING KIT
STANDARDS: ASTM D420, D1452 | AASHATO T86 This equipment, manufactured by Matest, is particularly useful for
This equipment, manufactured by Matest, comprises different initial site investigation work in remote areas. The kit is capable
augers, sampler and tools for soil investigations; the whole housed boring to a depth 10 - 12 mtrs depending on ground conditions.
in a wooden carrying case. The use of specially designed extension rod couplers reduces bore-
The kit consists of: hole friction to a minimum, permitting easy operation to considera-
S092-01 Auger head Ø 80 mm ble depth.
S093-01 Auger head Ø 100 mm Equipment consists of:
S094-01 Auger head Ø 150 mm - 12 boring rods 1 mtr long with 12 couplers
S052-01 Dutch soil auger head, Edelman type, Ø 150 mm - 2 pipe wrench and 1 tap wrench
S052-02 Gravel auger head Ø 50 mm - Core tube adaptor and clay core tube
S092ASTA Extension rod 1 m long with “T” handle - Driving head and clearing rod
S095 n° 5 extension rods, 1 m long - Long and short driving point
S053 Soil sampler Ø 38 mm complete with stainless steel - Auger tool and standard core tube
sample tube Ø 38x230 mm, jarring link, “T” handle. - Lifting/driving tool and hammer
S053-04 n° 5 Stainless steel sample tubes Ø 38x230mm - Die nut and hand tap
S052-03 Plastic cap ends for sample tubes All equipment supplied in a strong wooden box
Ø 38x230mm (12 pieces) Dimensions: 1050x260x120 mm
S054 Hand extruder for sample tube Ø 38x230 mm Weight: 35 kg approx.
S052-04 Stillson wrenches (2 pieces)
S052-05 Wooden carrying case.
Dimensions: 1140x490x360 mm
Total weight: 50 kg approx.

S052 KIT

Tel: +44 (0) 1442 402770

 E: [email protected]

462 RETURN TO HOMEPAGE

SECTION S | SOIL

HAND AUGERS
STANDARDS: ASTM D 420, D 1452 | AASHTO T86, T202
Designed for soil investigations and explorations, and to obtain
representative samples.
Complete with “T” handle, and rod 1 m long.
Made of special galvanized steel.

S095

S094 KIT
S093 KIT
S092 KIT

Models Description Weight kg

S092 KIT Hand Auger, Ø 80 mm x 1 m long 4
S093 KIT Hand Auger, Ø 100 mm x 1 m long 5
S094 KIT Hand Auger, Ø 150 mm x 1 m long 6
S095 Extension rod for above 1 m long
complete with coupling device 2

AUGER POWER HEAD TO OBTAIN DISTURBED SOIL

SAMPLES.
Supplied without augers, to be ordered separately
(see accessories).

MODELS

S096
AUGER POWER HEAD
Motor capacity 2 HP, two strokes,
without speed inverter.
Fitted with two handwheels, to be S097
used just by one operator.
S097
Drilling holes up to Ø 200 mm
and max. depth of 1000 mm AUGER POWER HEAD
It does not accept extension rods. Motor capacity 6 HP, two strokes, equipped with speed inverter to
Supplied without augers facilitate the extraction of the augers.
(see accessories) Fitted with two handwheels, to be used by two operators.
Supplied without augers (see accessories)
Weight: 10 kg approx.
Weight: 30 kg approx.

ACCESSORIES

S097-01 AUGER Ø 60 mm x 1 m long

S097-02 AUGER Ø 80 mm x 1 m long
S097-03 AUGER Ø 100 mm x 1 m long
S097-04 AUGER Ø 150 mm x 1 m long
S097-05 AUGER Ø 200 mm x 1 m long
S096
S097-06 EXTENSION ROD 1 m long

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 463

SECTION S | SOIL

SURFACE SOIL SAMPLERS

Used to take field standard core samples of compacted fill or
undisturbed soils and to evaluate density of compaction samples as
the ground surface.
The set consists of a drop hammer sliding on the drive rod and
falling on the drive head where the sampling tube is hold.
Steel made, galvanized against corrosion.

MODELS

S084 KIT
SURFACE SOIL SAMPLER 73 MM ID
STANDARDS: ASTM D2937 | CNR no. 22
Sampling tube is 73 mm inside diameter by 66 mm high.
Drop hammer is 5 kg
Total weight: 10 kg approx.

SPARE

S084-01 Sampling tube 73 mm diameter by 66 mm high.

S083 KIT
SURFACE SOIL SAMPLER 100 MM ID
STANDARD: BS 1377:9 S053-04 S054
S053
The sampling tube (core cutter) is driven into the soil by
using the rammer dropping on the driving dolly.
The sampled specimen is trimmed weighed and dried; S084 KIT
the density and the moisture content % is calculated.
Manufactured of plated steel.
The S083KIT includes:
S083-01 Driving rammer for Ø 100 mm core cutter.
Weight 7.5 kg
S083-02 Driving dolly for Ø 100 mm core cutter.
Weight 1 kg
S083-03 Core cutter (sampling tube) Ø 100 mm
by 130 mm length. Weight: 1 kg S083 KIT
Total weight: 9.5 kg approx.
S053
WATER LEVEL INDICATORS SOIL SAMPLER Ø 38 MM
Used to obtain indisturbed soil samples of Ø 11/2” (38 mm)
Utilized to measure the water level in boreholes, wells and any open The sampler is formed by:
underground structures. A light and audible signal are activated T handle with extension rod, 900 mm long
when the probe touches water. Jarring link 3/4”
Battery operated, the cable is marked at cm. intervals, drum Stainless sample tube Ø 11/2” x 9” (38x230 mm).
mounted and the stainless steel tip has diameter of 10 mm
Weight: 7 kg
Weight: 6 kg approx.

ACCESSORY

S054 HAND EXTRUDER used to extrude the soil specimens

Ø 11/2” from the sample tube.
Models Cable length
S061 50 m
S061-01 100 m SPARE
S061
S061-02 200 m S053-04 Stainless sample tube Ø 11/2” x 9”

Tel: +44 (0) 1442 402770

 E: [email protected]

464 RETURN TO HOMEPAGE

SECTION S | SOIL

POCKET PENETROMETERS AND SHEAR VANE DEVICES

STANDARDS: ASTM D 2573-94 | AASHTO T202

S068
S065 S066

S071 S076
S070
S076-01 S075

S071
MODELS
POCKET PENETROMETER
S065 Identical to mod. S070, but having a range of 0 - 16 kgf/cm².
DIAL POCKET PENETROMETER Suitable for very compacted soils.
For the classification of cohesive soft soils in terms of consistency, Weight: 800 g.
shear strength and approximate unconfined compression strength.
Direct value read in kgf/cm² on the graduated dial. S075
Range 0 - 6 kgf/cm² (0-588 kPa). Peak hold feature; zero setting by POCKET SHEAR VANE DEVICE RANGE: 0-1 KG/CM²
push button. Plunger Ø 6.35 mm Designed for the rapid determination in the field or in the laboratory
Weight: 300 g of shear strength of cohesive soils. The dial indicates directly the
shearing strength in kg/cm2.
S066 Complete with interchangeable stainless steel vane,
DIAL POCKET PENETROMETER 10x20 mm (Ø x height)
Identical to mod. S065 but with dial range 1-14 kg f/cm² Weight: 300 g.
(0-1373 kPa), suitable for medium and hard soil. Plunger Ø 6.35 mm
S076
S068 POCKET SHEAR VANE DEVICE RANGE: 0-2 KG/CM²
GEOPOCKET DIAL PENETROMETER Identical to mod. S075 but dial range 0-2 kg/cm².
Designed for a quick determination of the foundation soils, from
clay to sandy soils.
It indicates:
SPARE
- The angle of internal friction (sandy soils)
- The cohesion “c” (clay soils) and the approx. S076-01 Stainless steel vane 10x20 mm (Ø by height) for S075
Unconfined Compressive Strength. and S076 devices.
Peak hold feature; zero setting by push button.
Dual scale: 0-6 kgf/cm² (0-588 kPa) A106 MELTING POT, to melt wax and to cover soil samples
0-11 kgf/cm² (0-1079 kPa) keeping them to the original humidity.
Complete with 5 plungers Ø 6.4 - 10 - 15 - 20 - 25 mm See section “A” p. 00
Weight: 400 g

S070
STANDARD POCKET PENETROMETER
Designed for the rapid determination of soil consistency, shear
strength and approximate Unconfined Compression Strength. Scale
range 0-4.5 kgf/cm² with direct reading strength values.
Plunger Ø 6.35 mm
Weight: 300 g

A106

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 465

SECTION S | SOIL

S086 S088-10
LOAD RING PENETROMETER MOISTURE CONDITION VALUE (MCV)
Used to determine the bearing strength, compaction degree of AND CHALK CRUSHING VALUE (CCV)
subgrades, and also for determining the static penetration resist- STANDARDS: EN 13286-46 | BS 1377:4 (TRL approved)
ance of soil. This apparatus is used to measure the minimum comparative effort
Supplied complete with “T” handle, proving ring 100 kgf (1 kN) with required to produce near full compaction of a soil, and the rate at
maximum load pointer and calibration chart, extension rod 500 mm which a sample of chalk lumps are crushed.
long graduated every 100 mm, removable cone point 30° with The unit can be used to classify chalk as a fill material with satu-
1 sq. in. top area. rated moisture content.
Cadmium plated against corrosion. The apparatus comprises a robust frame where a rammer falls,
Weight: 5 kg approx. mould, scale, counter, accessories.
Weight: 60 kg approx.

S086

S088
PROCTOR PENETROMETER
STANDARD: ASTM D 1558
Used to determine in field the moisture-penetration resistance
relationship of fine grained soils.
Spring load scale 0-40 kg, subdiv. 1 kg, with direct max. value
reading in kg on the sliding rod.
Complete with 9 interchangeable stainless steel needles diameter:
4.52 - 5.23 - 6.40 - 9.07 - 12.83 - 16.54 - 20.22 - 24.79 - 28.55 mm, S088-10
accessories, carrying case.
Chromed finishing. LABORATORY SAMPLE MIXERS
Suitable to mix granular materials like soils and bituminous mix-
Weight: 5 kg approx.
tures, by using a whisk beater, as prescribed by EN, BS Spec.

MODELS

E095+B028-03 MIXER, 5 LITRE CAPACITY, complete with whisk

beater
B027+B027-03 MIXER, 20 LITRE CAPACITY, complete with whisk
beater
Technical details:
see p. 00, 00

S088
E095 + B028-03

Tel: +44 (0) 1442 402770

 E: [email protected]

466 RETURN TO HOMEPAGE

SECTION S | SOIL

S058
NUCLEAR MOISTURE DENSITY GAUGE
STANDARDS: ASTM D6938, D2950, C1040 | AASHTO T310
This product is used to measure moisture density of the construc-
tion material from surface to 300 mm of depth. This device can
measure and display wet density and dry density, percent moisture,
moisture content and other necessary engineering parameters
related to density and moisture content of materials.
Software features include self-test, special calibration, asphalt
thinlayer mode and built in diagnostics tests to help users identify
problems and solve them in the field.

Specifications:
- Density measurement range: 1120 to 2720 kg/m³
- Moisture measurement range: 0 to 640 kg/m³
- Precision at 2000 kg/m³, 150 mm - Depth: ± 3.5 kg/m³
- Moisture precision at 240 kg/m³: ± 4.42 kg/m³
Gauge dimensions: 580x310x220 mm
Weight: 14 kg approx.

ACCESSORIES for S058

S058
S058-11 S060
NUCLEAR GAUGE VALIDATOR AND CALIBRATION DEVICE NUCLEAR MOISTURE DENSITY GAUGE
STANDARDS: ASTM D6938, D2950 | AASHTO T310 STANDARDS: ASTM D6938, D2950, C1040 | AASHTO T310
This lightweight block may be used in the field to check the cali- It provides a rapid method of on-site determination of moisture
bration accuracy of the gauge and re-calibrate all model gauges, if density content of soils, aggregates and asphaltic concrete.
necessary. The software for determination of calibration constant is The microprocessor displays all functions directly.
user friendly and communicates directly with the gauge for down- Wet and dry density, moisture percent, moisture content, percent
load of constants. The block is constructed for the rugged construc- compaction for both soils and asphaltic concrete, void ratio and
tion industry with 1/8” Aluminum exterior with powder coat paint percent air voids.
and it is internally lined with shielding and composite compound in Surce is 300 mm with index rods for direct transmission depths in
secured enclosure. 50 mm increments. Stores up to 320 field tests, transferable to PC
For calibration, the user requires a PC with Windows® operating or printer.
system.
Gage dimensions: 400x220x140 mm
Dimensions: 480x460x300 mm Shipping weight: 14 kg approx.
Weight: 38 kg approx.

S058-12 SOFTWARE to be used with the validator for calibrations.

S058-11 S060

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 467

SECTION S | SOIL

S050-10 S059
ELECTRICAL DENSITY GAUGE GEOGAUGE-NON NUCLEAR GAUGE FOR SITE
STANDARD: ASTM D7698 SOIL COMPACTION CONTROL
This Electrical Density Moisture Gauge is a “nuclear-free” alternative YOUNG MODULUS
for determining the moisture and density of compacted soils used STANDARD: ASTM D6758
in road beds and foundations. This portable, battery powered unit is Technical features:
capable of being used anywhere without the concerns and regula-
Stiffness 3 to 70 MN/m
tions associated with nuclear safety. Its user-friendly step-by-step
Young’s Modulus 26 to 610 Mpa
menu guides the user through each step of the testing procedure to
Measure Depth from 230 to 310 mm.
established curves for the material being tested.
Measure Duration 75 seconds
Easy-to-use the Gauge can be used as a construction aid to monitor
Power Six D-Cell Batteries
day-to-day compaction operations by providing performance and
(500 to 1500 measurements)
measurement results highly comparable to those achieved with
Dimensions with case 470x420x330 mm
traditional methods, including the nuclear gauge and/or sand-cone
Weight 15 kg
and oven moisture test combination.
When conducting a test, the instrument measures and displays the
results for wet and dry density, gravimetric moisture content and
percent compaction.
Advantages:
It does not require a highly-trained technician.
It does not require special handling for shipping or the regulatory
compliance for hazardous materials.
It is easy-to-learn and easy-to-use with its step-by-step menu.
Lightweight and easily transportable.
It is accurate and repeatable with results that mirror known
testing methods.
Dry density accuracy: within 3% of standard tests.
Moisture density accuracy: within 2% of standard tests.
The Gauge includes: Console/Case, 4-tapered 6” darts, hammer,
soil sensor and cables, dart template, temperature probe, battery
charger, field verifier, safety glasses.
Dimensions: 533x432x203 mm
Shipping Weight: 16 kg approx.
S059

This is the only hand portable gauge available to provide the

required simplicity, quickness and precision to directly measure and
monitor the in-place engineering properties and do so at construc-
tion speed. The device applies a constant load vibrating force to the
soil’s surface and measures the resulting displacement.
This dynamic technology simulates actual in-use conditions.
One instrument to link design specifications with compaction in 75
seconds for enhanced QC/QA.
Applications include subgrade, subbase, base monitoring the
strength gain of lime, cement, fly-ash and polymer stabilised mate-
rials, monitoring the re-compacting of asphalt and cold in-place
recycling to peak properties to prevent wasted effort and damaging
over-compaction. The device compliments and provides alternative
S050-10 to resilient modulus, Falling Weight Deflectometer, field California
Bearing Ratio, plate load test, dynamic cone penetrometer and
other measures of strength, stiffness, modulus and deflection.

ACCESSORIES

S059-01 INFRARED INTERFACE AND SERIAL PORT ADAPTER with

Software Template (PC only).
S059-02 VERIFIER MASS (verifies the non nuclear gauge operation).

Tel: +44 (0) 1442 402770

 E: [email protected]

468 RETURN TO HOMEPAGE

SECTION S | SOIL

S078-01

S077

S077 S079
EARTH RESISTIVITY METER SEISMOGRAPH, THREE CHANNELS
STANDARDS: ASTM G57 | BS 1377:3 Applications:
Used for ground water researches even to great depths, gravel - Depth determination of bedrock.
deposit evaluation, geological surveys for the construction of roads, - Determination of elastic-dynamic properties of surface deposits.
pipelines etc., study and prevention of landslides. - Foundation studies.
- Preliminary investigations for the realization of important works.
The system consists of:
- Cost estimation for excavation.
Resisitivity measuring instrument with Software
- Evaluation of elastic-dynamic modules of materials.
Dimensions: 210x170x90 mm - Downhole survey with tridimensional borehole geophone.
Weight: 2 kg - Microseismics.
The seismograph is supplied complete with set of accessories to
2 potential copper electrodes perform seismic refraction tests.
2 current electrodes This seismograph can perform also Downhole and Crosshole
2 cable reels with 300 m of cable measurements by adding suitable kit of devices (optional accesso-
2 cable reels with 100 m of cable ries on request).
2 hammers, set of standard accessories
Dimensions: 210x170x90 mm
Weight: 2 kg approx.

ACCESSORY

S078-01 RECHARGEABLE ACCUMULATOR, TWO PIECES

Energy source for geoelectrical surveys (in alternative to
dry batteries or generators).
Dimensions: 35x25x24 cm
Weight: 6 kg approx.

S079

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 469

SECTION S | SOIL

S132N S135 ACIDITY TEST KIT OF WATER to evaluate the potential cor-
COLOR STANDARD GLASS SCALE rosive. The set comprises different graduated containers,
reagents, syringe, pipette, instructions.
ORGANIC IMPURITIES IN SOILS
STANDARDS: ASTM C40-11 method | AASHTO T21 S136 CHLORIDE TEST KIT OF WATER. The set comprises
For the determination of the Organic impurities in soils and fine different reagents, graduated containers, pipette, syringe,
aggregates. instructions.
The chart has 5 glass reference scales.
S137 HARDNESS TEST KIT OF WATER, for calcium and magne-
sium percentage determination.
The set comprises different reagents and graduated
containers, syringe, pipette, instructions.

S137-01 ALKALINITY TEST KIT to determine the total alkalinity of

water.

S138 ORGANIC MATTER TEST SET

Formed by different bottles, reagents and accessories to
S132-02 perform about 50 tests for each of the soil factors on the
S132-01
S132-03 following tests:
S132N
pH - pH Nitrate - Ammonia - Nitrate Nitrogen etc.

S132-01 GRADUATED IMPURITIES TEST BOTTLE, stoppered, pyrex

glass, 500 ml - ASTM C40
S132-02 GRADUATED IMPURITIES TEST BOTTLE, stoppered, pyrex
glass, 500 ml, marked at 130 and 200 ml - UNI 8020-14
S132-03 GRADUATED IMPURITIES TEST BOTTLE, stoppered, pyrex
glass, 1000 ml - ASTM C40
V300-24 SODIUM HYDROXIDE, pack of 1000 g

S133N
MUNSELL SOIL COLOUR CHART
Colour matching charts for soil identification. S137-01
The set consists of 7 constant hue charts with 196 colours, plus
two tropical soil colour charts.

S133N

S138

S136

S135
S137

Tel: +44 (0) 1442 402770

 E: [email protected]

470 RETURN TO HOMEPAGE

SECTION S | SOIL

UNIVERSAL SAMPLE EXTRUDERS

STANDARDS: EN 13286-2, 13286-47 | ASTM D698, D1587, D1883 | BS 598, 1377:4, 1924:2
S111
MOTORISED HYDRAULIC EXTRUDER
Used for a smooth and rapid extrusion of soil samples from tubes also of thin walls with minimum disturbance. The unit extrudes samples from
Ø 35 up to 150 mm (external diameter 160 mm) with max. stroke of 900 mm.
The hydraulic piston is equipped of speed adjuster and can be stopped in any excursion’s position.
Max. load: 70 kN (7000 kg)
The extruded sample is held in place by a receiving table adjustable in height and easily lowered along side the machine to save space.
Complete with adaptors (ring + tamper) to extrude samples having diameter
38.1 (11/2”), 83, 100 mm.
Power supply: 230V 1ph 50Hz 1300W
Dimensions (working position): 2741x635x1200 mm
Weight: 160 kg approx.
S114
UNIVERSAL EXTRUDER
Used to extrude samples having diameter 4”,
6”, 100 mm, 150 mm. It can therefore extrude
CBR, Marshall and Proctor specimens.
The extruder is actuated by a 50 kN hydraulic
jack, having ram travel of 190 mm + 170 mm
screw.
Supplied complete with adaptors S111
Dimensions: Ø 300x500 mm
Weight: 32 kg approx. S112
SCREW EXTRUDER - HAND OPERATED
S114
NEW The unit extrudes samples from Ø 35 to 101.6 mm with max. stroke
S110 of 650 mm. Supplied complete with adaptors to extrude samples
VERTICAL SOIL EXTRUDER, HAND OPERATED having diameter 38.1 (11/2”), 83, 100 mm, supporting bench,
The extruder is actuated by a 60kN hydraulic jack, ram travel 480 mm. sample receiving table both adjustable in height and lowerable.
It accepts standard U4 tubes and samples from 35 to 152 mm
diameter. Dimensions: 1700x700x1200 mm
Dimensions: 350x320x1150 mm Weight: 90 kg approx.
Weight: 50 kg

ACCESSORIES

S110-01 ADAPTOR for extruding 38, 100, 150 mm, 4”, 6” samples
S110-02 ADAPTOR for extruding 38 mm diameter samples only
S110-03 SAMPLE TUBE U100 (U4), Ø 106x457.2 mm
S110-04 TAMPER to extrude the sample from S110-03 tube

S112

ADAPTORS (ring and tamper) for S111 and S112 Extruders:

Code Diameter
S113-10 38.1 mm ( 1 1/2”) (spare)
S113-11 50.8 mm (2”)
S113-12 76.2 mm (3”)
S113-13 101.6 mm (4”)
S113-14 83 mm (spare)
S113-15 100 mm (spare)
S110 S113-16 35 mm
with accessories S113-17 150 mm (only for mod. S111)

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 471

SECTION S | SOIL

S118
SOIL DIE CUTTER | SAMPLER
Used to compress loose soils to prepare samples, and to hollow punch (cut) and extrude soil
specimens for consolidation, shear, triaxial, unconfined tests.
The sampler is used with the hollow punches S122 to S122-20 and tampers S123 to S123-16
Upper plate diameter is 120 mm and max. vertical daylight is 470 mm
Dimensions: 500x300x900 mm
Weight: 30 kg approx.

HOLLOW PUNCHES AND TAMPERS

Used to prepare soil samples and to fit them into the relevant cells to perform triaxial, consoli-
dation, shear, unconfined tests.
The punch has thin walls with cutting rim, and the tamper expels the specimen from the
hollow punch by inserting it directly into the cell without disturbing the same.

Cell Dimensions Height Hollow Punch Tamper

Consolidation Ø 50.47 20 mm S122 S123
Consolidation Ø 63.50 20 mm S122-19 S123-05
Consolidation Ø 71.40 20 mm S122-01 S123-01
Consolidation Ø 75.00 20 mm S122-17 S123-04
S118 with punches and tampers
Consolidation Ø 79.80 20 mm S122-02 S123-02
Consolidation Ø 112.80 25 mm S122-03 S123-03 S120
SOIL LATHE
Designed to reduce by trimming the diameter
Consolid. Permeab. Ø 50.47 20 mm S122-04 S123 of a soil sample unitil reaching the desired
Consolid. Permeab. Ø 63.50 20 mm S122-20 S123-05 diameter size by using a wire saw. The lathe
Consolid. Permeab. Ø 71.40 20 mm S122-05 S123-01 is hand-operated, the height is adjustable up
to 230 mm, and it accepts samples from
Consolid. Permeab. Ø 75.00 20 mm S122-18 S123-04
Ø 38 to 110 mm.
Consolid. Permeab. Ø 79.80 20 mm S122-06 S123-02 Supplied complete with three sets of platens
Consolid. Permeab. Ø 112.80 25 mm S122-07 S123-03 for samples Ø 38-50,47-60 mm, wire saw
and 6 blades.
Dimensions: Ø 460x720 mm
Shear Ø 50 23 mm S122-08 S123-08
Weight: 20 kg approx.
Shear Ø 60 23 mm S122-09 S123-09
Shear Ø 63.5 23 mm S122-21 S123-17
Shear Ø 100 23 mm S122-10 S123-10
Shear 60x60 23 mm S122-11 S123-11
Shear 100x100 23 mm S122-12 S123-12

Triaxial + Unconf. Ø 38 76 mm S122-13 S123-13

Triaxial Ø 50 100 mm S122-14 S123-14
Triaxial Ø 70 140 mm S122-15 S123-15
Triaxial Ø 100 200 mm S122-16 S123-16

S124
S120
V112-01
ACCESSORY
V113
S125 S120-01 UPPER TRIMMING PLATEN
V112-01 PORCELAIN MORTAR Ø 125 by 65 mm complete with porcelain pestle.
V113 PESTLE, rubber headed. available from Ø 38 to 110 mm
S124 WIRE SAW for trimming soil specimens. Complete with six blades. When ordering please specify
S125 TRIMMING KNIFE to prepare samples. required diameter.

Tel: +44 (0) 1442 402770

 E: [email protected]

472 RETURN TO HOMEPAGE

SECTION S | SOIL

S140 B073-01
ION EXCHANGE DEVICE MAGNETIC STIRRER/HEATER
SULPHATE CONTENT DETERMINATION For titration and stirring of liquid and semi-solid materials.
STANDARD: BS 1377:3 Plate Ø 150 mm.
This device is used to know the sulphate content of ground water Variable speed and temperature
and water soil extracts. by electronic regulators.
Consisting of a ion exchange glass tube 400 mm long, connector Supplied complete with magnetic
and bottom flask 500 ml capacity. teflon coated follower.
The unit is assembled on a stand. Power supply:
Dimensions: 190x110x600 mm 230V 1ph 50-60Hz 700W
Weight: 5 kg approx.

ACCESSORY

V300-30 Ion exchange resin, 500 g

B073-01

pH METERS, DIGITAL
STANDARDS: ASTM D1067 | BS 1377:3

V215
pH METER, POCKET
Battery operated, with replaceable electrode
Range: 0.00 to 14.00 pH - Resolution 0.01 pH
Manual 2 points calibration.
Power supply: standard battery, 3000 hours use.
Supplied complete with: electrode, batteries,
5+5 kit of pH 4 and 7 calibration solutions
V300-30 Weight: 70 g
S140 V215
V215-01N
CHLORIDE CONTENT, RAPID METHOD pH/mv/°C METER, PORTABLE, WATERPROOF
STANDARDS: BS 812:117 | BS 1377:3 Range pH: 0.00 to 14.00 - Resolut. 0.01 pH
Used to estimate the chloride content of aqueous solutions in sand mV: ± 1999 - Resolut. 0.1mV - 1mV
and fine aggregates. Temperature: 0 to 100°C
Manual 2 points calibration.
A019-01 QUANTAB Chloride Titrator Strips, type 1175, range
Automatic temperature compensation.
0.005% to 0.1% (30 to 600 ppm) Na Cl. Pack fo 40 strips.
Power supply: 9V battery, 100 hours use.
A019-02 QUANTAB Chloride Titrator Strips, type 1176, range Supplied complete with: electrode, temperature probe, battery,
0+05% to 1% (300 to 6000 ppm) Na Cl. Pack of 40 strips. calibration solutions, case.
Weight: 180 g
SULPHATE CONTENT, RAPID METHOD
STANDARD: BS 1377:3
Used to determine the sulphate ions in aqueous solutions of sand
and fine aggregates.
A019-03 SULPHATE TEST STRIPS, detection range 200 to
1600 mg/l. Pack of 100 strips.

V215-01N
A019-02
A019-01 A019-03 Note: Complete range of pH meters at p. 000

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 473

SECTION S | SOIL

A028
UNIVERSAL CARBIDE METER
STANDARDS: BS 6576 | AASHTO T217 | ASTM D4944
For the rapid and accurate determination of moisture content in soil
sand, gravel, aggregates etc, based on the calcium carbide method.
It is possible to vary the sample weight from 3 to 100 g achieving a
moisture range 50% (3g) - 7.5% (20g) - 1.5% (100g).
The bottle is calibrated and equipped with a surface thermometer.
The glass ampoule containing the calcium carbide is broken when
the bottle is closed and shaken, granting better accuracy to the test.
The instrument comprises the testing bottle with manometer, small
balance, 25 ampoules of reagent, accessories, case.
Dimensions: 520x340x140 mm
Weight: 6 kg approx.

A117 + A116-11 + A116-12 + C279-02

A117
END-OVER-END SHAKER
PARTICLE DENSITY OF SOILS
STANDARD: BS 1377:2
Used to determine the particle density of soils containing up to 10%
A028 of particles retained on a 37.5 mm sieve.
It rotates two gas jars at approx. 50 rpm to satisfy BS Standard.
Note: Other carbide meter models: see p. 00 The shaker is equipped with an original friction device conforming
the unit to CE Safety Directive.
Supplied without gas jars to be ordered separately
SPARE
Power supply: 230V 50Hz 1ph 150W
A028-11 Carbide Ampoules (pack of 100) Dimensions: 550x430x500 mm
Weight: 20 kg approx.

V023-01 A028-11
MOISTURE DETERMINATION BALANCE
160 g capacity x 0.001/0.01 g sensitivity with tare up to 10 g.
Samples are dried by a infrared lamp with adjustable heat control.
A built-in-timer 0-61 min. switches off the heater at the end of the
drying cycle which is signaled by a bell. Moisture loss percentage
and residual mass are read directly
A116-12
from the lighted scale.
A116-11
Power supply: 230V 1ph 50-60Hz
ACCESSORIES

A116-11 GAS JAR to determine the specific gravity of soils.

Complete with glass cover.
Diameter 75 mm by 300 mm height
Weight: 1.3 kg
A116-12 RUBBER BUNG for the gas jar A116-11
C279-02 SEPARATE CONTROL PANEL, complete with ON/OFF
V023-01 switch, timer, fuse, electric protections.

Tel: +44 (0) 1442 402770

 E: [email protected]

474 RETURN TO HOMEPAGE

SECTION S | SOIL

S155 KIT ACCESSORIES

PARTICLE SIZE ANALYSIS OF SOILS
HYDROMETER METHOD V172-02 SOIL HYDROMETER 152H, range -5 to 60 g/l
STANDARDS: ASTM D422 / AASHTO T88 (alternative to mod. V172)
This complete set is used to determine the quantitative size distri- S155-02 BUNG, rubber, for the cylinder S155-01
bution of very fine particle in soils such as clay and silt. S155-08 COOLING COIL for S155-09S
S155-11 NOMOGRAPHIC CHART, for stoke's law determination.
S155 KIT The complete set comprises: S156 STIRRER, manual, for cylinders 1000 ml capacity
S155-01 Hydrometer jar, 1000 ml capacity (6 pieces) mod. S155-01
V172 Soil hydrometer, 151H, range 0.995 to 1.038 g/ml C306-03 SEPARATE CONTROL PANEL, complete with on/off
with div. 0.001 switch and electric protections, to get S155-09 heater to
S155-04 Glass tank, dimensions: 600x300x380 mm CE Safety Directive.
S155-09 Heater, professional type, complete with thermostat,
cooling coil, water circulating unit.
230V 1ph 50-60Hz 1000W
S155-10 Thermometer, range 0 - 50 °C, subdiv. 0.5 °C.
V104-03 Beaker, pyrex, 250 ml capacity C306-03
V300-23 Sodium Hexametaphosphate, 1000 g
S156-01 KIT High speed stirrer, 10.000 rpm, complete with cup,
ACCESSORIES according to NF P94-057 Standard
paddle, anti-splash baffle, for dispersing soil particles
in water. 230V 1ph 50-60Hz S155-03 HYDROMETER JAR, 2500 ml capacity,
Total weight: 60 kg approx. 85 ± 5 mm Ø, graduated at 500, 1500, 2000 ml.
ALTERNATIVE: S156-03 STIRRER MANUAL, 600 mm long for cylinders
2500 ml capacity, mod. S155-03.
S155S KIT
V172-03 SOIL HYDROMETER 0.995 to 1030 g/ml.
PARTICLE SIZE ANALYSIS OF SOIL
Same as S155 KIT but:
S155-09S HEATER is simple type, complete with thermostat and SPARES for S156-01 KIT Stirrer
water circulating unit but without cooling coil
(see accessories S155-08). 230V 1ph 50-60Hz S156-11 Anti-splash baffle
S156-12 Paddle
S156-13 Cup (beaker)

S155S KIT

S156-11
S156-13
S156-12

S156-03
S155 KIT S156-01 KIT S156

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 475

SECTION S | SOIL

S143 KIT S157 KIT

PARTICLE SIZE DISTRIBUTION PIPETTE METHOD METHYLENE BLUE TEST SET
STANDARD: BS 1377.2 CLAY CONTENT IN FINE AGGREGATES
This equipment is used to determine the quantitative size distribu- STANDARDS: EN 933-9 | NF P94-068 | UNI 8520-15 | UNE 83180
tion of very fine particle in soils, like clay and silt. Utilized to determine the clay content in the fine portions of
aggregates. The set comprises:
The complete set comprises:
S157-01 Electric stirrer adjustable from 400 to 700 rpm, com-
S144 Andreasen pipette, 25 ml capacity, for an accurate extrac-
plete with Ø 70 mm propeller. 230V 1ph 50-60Hz
tion of the quantities of soil in suspension for analysis.
S157-06 Support base for stirrer
S144-01 Pipette stand, to accurately raise and lower the pipette S157-02 Burette 50 x 0.1 ml with stopcock
with no transmission of vibration to not disturb the S157-07 Support base for burette
sample suspension. Weight: 10 kg S157-08 Pan 200x150x80 mm
S144-02 Sedimentation cylinder, 500 ml capacity S157-03 Filter paper Ø 90 mm (pack of 100)
S144-03 Rubber bung for cylinder S157-04 Glass rod Ø 8x300 mm
S157-05 2000 ml capacity plastic beaker
S144-04 Evaporating dish, glass, Ø 90 by 50 mm height.
V300-28 Methylene blue, 100 g
V172-03 Soil hydrometer, long stem, 0.995 to 1030 g/ml. V300-29 Kaolinite, 500 g
S155-04 Glass tank, dimensions: 600x300x380 mm. Total Weight: 10 kg approx.
S155-09 Heater, professional type, complete with thermostat,
cooling coil, circulation unit. Note: each item can be ordered separately.
Alternative: S155-095 simple type, see p. 000
S157-10 AUTOMATIC DISPENSER, 0-10 ml x 0.1 ml grad.
S155-10 Thermometer, range 0 - 50 °C, subd. 0.5 °C.
Capacity 1000 ml (alternative to S157-02+S157-07)
Total weight: 40 kg approx.
Note: each item can be ordered separately.

ACCESSORIES

S144-10 ANDREASEN PIPETTE, capacity: 10 ml

C306-03 CONTROL PANEL, complete with on/off switch and electric
protections, to get S155-09 heater to CE Safety Directive.
A117 END-OVER-END SHAKER. Technical details: see p. 00

S143 KIT

S144 S157-10

C306-03
S144-01

S155-09 S157 KIT

S157-20
S155-04 AUTOMATIC METHYLENE BLUE TESTER
This instrument determines automatically the quantity of clay in sand.
It grants accurate and repeatable test results, saving a lot of time
(approx. 30 minutes each test). The apparatus is composed of:
precision pump, colorimeter, con-
S144-02 trol unit, filters, liquids, powder,
accessories.
To perform the test S157-01
and S157-06 devices are also
needed.
Power supply: 230V 1ph 50Hz
V172-03 Dimensions: 300x400x350 mm
S144-03 S144-04 Weight: 10 kg approx. S157-20

Tel: +44 (0) 1442 402770

 E: [email protected]

476 RETURN TO HOMEPAGE

SECTION S | SOIL

S158 KIT
SAND EQUIVALENT TEST SET S158-20 KIT
STANDARDS: ASTM D2419 | AASHTO T176
SAND EQUIVALENT TEST SET
This complete set comprises: STANDARDS: EN 933-8 | NF XP18-598 | CNR N.27
S158-01N Plexiglass measuring cylinder engraved at 100 and UNI 8520-15 | UNE 83131
380 mm, with transparent adhesive label, graduated in This complete set comprises:
mm and inch (5 pieces)
S158-03N Plexiglass measuring cylinder engraved at 100 and
S158-02 Rubber stopper for cylinder (2 pieces) 380 mm (5 pieces)
V176-02 Graduated rule 500 mm, stainless steel S158-02 Rubber stopper for cylinder (2 pieces)
V136-01 Funnel, wide mouth V176-02 Graduated rule 500 mm, stainless steel
S158-04N Measuring can 85 ml capacity V136-01 Funnel, wide mouth
V121 Plastic bottle, 5 litre capacity S158-05 Measuring can 200 ml capacity
S158-06 Irrigator tube with stopcock and syphon assembly V121 Plastic bottle, 5 litre capacity
S158-07N Weighted foot assembly for sand level S158-10 Irrigator tube with stopcock and syphon assembly
A052-44 Sieve, Ø 200 mm, opening 4.75 mm S158-13 Weighted foot assembly for sand level
S158-09 Concentrated stock solution, 1000 ml A052-37 Sieve, Ø 200 mm, opening 2 mm
V170 Stop watch, digital S158-09 Concentrated stock solution, 1000 ml
S158-11 Clamp stand set to hold the syphon assembly with bottle V170 Stop watch, digital
S158-12 Portable carrying case, dimensions: 550x250x400 mm S158-11 Clamp stand set to hold the syphon assembly with bottle
Total Weight: 18 kg approx. S158-12 Portable carrying case, dimensions: 550x250x400 mm
Total Weight: 18 kg approx.

S158-20 KIT

ACCESSORY
S158 KIT
S158-08 METALLIC FUNNEL, conforming to
EN 933-8 / NF XP18-598
UNI 8520/15 Specifications.

Note: each item can be ordered separately. S158-08

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 477

SECTION S | SOIL

S159 KIT S159-01 KIT

SAND EQUIVALENT TEST SET (SIMPLE) SAND EQUIVALENT TEST SET (SIMPLE)
STANDARDS: ASTM D2419 | AASHTO T176 STANDARDS: EN 933-8 / NF XP18-598 / UNI 8520-15
CNR N.27 / UNE 83131
The set comprises:
The set comprises:
S158-01N Plexiglass measuring cylinder engraved at 100 and
S158-03N Plexiglass measuring cylinder engraved at 100
380 mm, with transparent adhesive label, graduated
and 380 mm (4 pieces)
in mm and inch (4 pieces)
S158-02 Rubber stopper for cylinder (2 pieces)
S158-02 Rubber stopper for cylinder (2 pieces)
V176-02 Graduated rule 500 mm, stainless steel
V176-02 Graduated rule 500 mm, stainless steel
V136-01 Funnel, wide mouth
V136-01 Funnel, wide mouth
S158-05 Measuring can 200 ml capacity
S158-04N Measuring can 85 ml capacity
V121 Plastic bottle 5 litre capacity
V121 Plastic bottle 5 litre capacity
S158-10 Irrigator tube with stopcock and syphon assembly
S158-06 Irrigator tube with stopcock and syphon assembly
S158-13 Weighted foot assembly for sand level
S158-07N Weighted foot assembly for sand level
S158-09 Concentrated stock solution, 1000 ml
S158-09 Concentrated stock solution, 1000 ml
Total Weight: 5 kg approx.
Total Weight: 5 kg approx.

S159-11
S159-11

S159 KIT S159-01 KIT

ACCESSORY ACCESSORY

S159-11 CARRING CASE, PLASTIC, housing the sand equivalent set S158-08 METALLIC FUNNEL, conforming to
mod. S159 KIT or S159-01 KIT except the bottle V121 EN 933-8 | NF XP18-598 | UNI 8520/15 Specifications.

MEASURING CYLINDERS
Available Models :
S158-01N
STANDARDS: ASTM D2419 | AASHTO T176
PLEXIGLASS MEASURING CYLINDER, engraved at 100 and 380 mm,
with transparent adhesive label graduated in mm and inches.
AS ALTERNATIVE:
S158-01GN
STANDARDS: ASTM D2419 | AASHTO T176
PLEXIGLASS MEASURING CYLINDER, engraved at 100 and 380 mm
with additional engraved scale from 0 to 380 mm
S158-03N S158-08
S158-03N S158-01GN S158-01N
STANDARDS: EN 933-8 | NF XP18-598
PLEXIGLASS MEASURING CYLINDER, engraved at 100 and 380 mm Note: each item can be ordered separately.

Tel: +44 (0) 1442 402770

 E: [email protected]

478 RETURN TO HOMEPAGE

SECTION S | SOIL

S160 N S160-01 N
MOTORIZED SAND EQUIVALENT SHAKER MOTORIZED SAND EQUIVALENT SHAKER
STANDARDS: EN 933-8 | ASTM D2419 | AASHTO T176 Same as S160N, but equipped with steel Security Cabinet, con-
NF XP18-598 | UNE 83131 | CNR N.27 forming to CE Safety Directive. When opening cabinet’s door during
UNI 8520-15 shaker working, a microswitch automatically stops the machine.
The unit provides a constant uniform shaking with automatic cycle
test. Oscillating excursion is 203 mm at 175...180 adjustable
strokes/min. rate. Complete with digital timer that automatically
stops the shaker at the end of the test. It cannot be sold in CE
markets without security cabinet (see model S160-01 N)
Power supply: 230V 1ph 50Hz 250W
Dimensions: 700x360x350 mm
Weight: 30 kg approx.

S160-01N + S158-03 + S158-02

S160N + S158-03 + S158-02

S161
SAND EQUIVALENT SHAKER HAND OPERATED
STANDARDS: EN 933-8 | ASTM D2419 | NF XP18-598
AASHTO T176 | UNI 8520-15 | UNE 83131
Hand operated working through handwheel.
Complete with mechanical strokes counter.
Dimensions: 700x350x420 mm approx.
S161
Weight: 20 kg approx.

ASSESSMENT OF FINES:
GRADING OF FILLERS
STAMDARD: EN 933-10
A058-05N
AIL JET SIEVE SHAKER
Suitable for sieving powder and dry grain
products up to 5 microns.
Technical details: see p. 00

A058-05N

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 479

SECTION S | SOIL

SPECIFIC GRAVITY OF SOILS DESICCATORS BOROSILICATE GLASS

Complete with perforated porcelain plate.
E136
WATER BATH, DIGITAL
Without vacuum With vacuum
STANDARD: BS 1377:2
A035 Ø 200 mm A039 Ø 200 mm
For the determination of particle density, pyknometer method,
according to BS 1377:2 Specifications, and for general laboratory A036 Ø 250 mm A040 Ø 250 mm
purposes. A036-01 Ø 300 mm A040-01 Ø 300 mm
All stainless steel made, with wool insulation and water circulation
electric stirrer, the bath ensures an uniform and constant temperature.
Complete with digital thermostat and dual safety thermostat with ACCESSORY
higher thermic threshold ensuring safe working conditions.
A cooling device to be connected to the water net is used when V300-15 DESICCATORS SALTS Silica gel box 1000 g
room temperature exceeds the requested one.
Capacity: 40 litres
Temperature range: ambient to 60 °C, accuracy ± 0.5 °C
Internal dimensions: 510x350x230 mm
Overall dimensions: 680x420x420 mm
Power supply: 230V 1ph 50Hz 1200W
Weight: 28 kg approx.

A039 A035

V202
ASPIRATOR PUMP
To be connected to the water net with a minimum
pressure of 0.7 kg/cmq, it produces a moderate
vacuum pressure.
Weight: 100 g
E136

V202
SPECIFIC GRAVITY BOTTLE, GAY LUSSAC TYPE S147
STANDARDS: BS 1377:2 | ASTM D854 | AASHTO T100
NF P18-054, NF P94-054
CONE PYKNOMETER
STANDARDS: EN 1097-6 | BS 1377:2
Pyrex glass made, complete with capillary tube stopper, these
bottles are used to determine the specific gravity and density of fine Used for the determination of specific
soils and filler in fine aggregates. gravity and water absorption of sands
and fine aggregates.
Models Capacity Glass jar with aluminium cone and
V108 25 ml rubber seal.
Capacity: 1 kg
V108-01 50 ml
V108-02 100 ml
V108-03 250 ml S147

S148
SAND ABSORPTION CONE
AND TAMPER
STANDARDS: EN 1097-6 | BS 812
Used to determine the specific gravity
and water absorption of fine aggregates.
Weight: 500 g approx.

V108-01 V108-02 S148

Tel: +44 (0) 1442 402770

 E: [email protected]

480 RETURN TO HOMEPAGE

SECTION S | SOIL

S170-01
S170

S170-05

LIQUID LIMIT CASAGRANDE METHOD

Used to evaluate the relationship between the moisture percentage
of a soil sample and the number of blows required to close a groove
made into the soil and therefore to determine when a clay soil
S172 S172-01
changes from a plastic to a liquid state.
The unit comprises a removable brass cup which through a cam
device drops on a bakelite base (or hard rubber base). Supplied ACCESSORIES
complete with drops counter, but without grooving tool which has
S173-02 ROUGH BRASS CUP, with central smooth band 10 mm
to be ordered separately.
wide, as requested by NF P94-051 Standard, used for
The instrument is available in two versions:
soils having low plasticity
- hand operated through crank (left or right side)
S173-03 GROOVING TOOL, to UNI 10014 - AASHTO T89 Spec.
- motor operated at 120 drops/min speed, ensuring better
S173-04 GROOVING TOOL, to ASTM D 4318 Specifications
uniformity and accuracy
S173-04P GROOVING TOOL, hard plastic made. Pack of 10 pcs.
MODELS Standard: ASTM D 4318
S173-05 GROOVING TOOL, to NF P94-051-1 Specifications
S170 S173-06 GROOVING TOOL, to BS 1377:2 Specification
LIQUID LIMIT DEVICE S173-06P GROOVING TOOL, hard plastic made. Pack of 10 pcs.
Hand operated with left side crank and hard rubber base. Standard: BS 1377:2
STANDARDS: ASTM D4318 | AASHTO T89 | UNI 10014
comparable to: BS 1377:2 | UNE 7377
Weight: 3 kg approx.
S170-05
LIQUID LIMIT DEVICE S173-04P
Hand operated.
Same as mod. S170, but with right side crank.
S170-01
LIQUID LIMIT DEVICE
Hand operated with bakelite base, chromed cup.
STANDARD: NF P94-051-1
S172
LIQUID LIMIT DEVICE
Motor operated with hard rubber base.
STANDARDS: ASTM D4318 | AASHTO T89 | UNI 10014
S173-01...S173-08
comparable to: BS 1377:2 | UNE 7377
Power supply: 230V 1ph 50Hz SPARES
Weight: 4.5 kg approx.
S173-01 Brass cup. (ASTM, BS, UNI, UNE, AASHTO).
S172-01 S173-07 Chromed cup (NF P94-051-1).
LIQUID LIMIT DEVICE S173-08 Coupling piece between cup and device, hand operated
STANDARD: NF P94-051 models.
Motor operated with bakelite base, chromed cup. S173-09 Coupling piece between cup and device, motor operated
Power supply: 230V 1ph 50Hz models.

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 481

SECTION S | SOIL

S175
SHRINKAGE LIMIT
STANDARDS: ASTM D 427 | AASHTO T 92 | UNI 10014
UNE 103-108 | NF XP94-060-1 | BS 1377:2
Used to determine the maximum moisture content at which the soil
does not shrink after drying the sample.
Complete with carrying case.
The set comprises:
V122-04 Shrinkage dish, Ø 45x12,7 mm (2 pieces)
V122-03 Crystallizing dish, Ø 57x32 mm
S175-03 Shrinkage prong plate, made from plexiglass material
with three metal prongs
S175-04 Glass evaporating dish, Ø 120 mm flat bottom
V100-01 Graduated cylinder 25 ml capacity
V192 Flexible spatula, 100 mm blade
S178
Case dimensions: 390x300x100 mm
Weight: 2 kg approx.

Note: each item can be ordered separately. S178

PLASTIC LIMIT
STANDARDS: ASTM D4318 | AASHTO T90 | BS 1377:2
UNI 10014 | UNE 103-104 | NF P94-051
The plastic limit determines the lowest moisture content of a soil, by
wich a sample can be rolled into threads Ø 3 mm without breaking
the same neither longitudinally or transversely.
The set complete with carrying case comprises:
S178-01 Glass plate 300x250x10 mm
S178-02 Rod caliper Ø 3 mm
V114-03 Mixing porcelain dish Ø 120 mm
V192 Flexible spatula, 100 mm blade
V122 Aluminium moisture tins Ø 55x35 mm (Q.ty 6)
Case dimensions: 400x340x100 mm
Weight: 5 kg approx.

Note: each item can be ordered separately.

S175 ACCESSORIES

S178-06 GLASS PLATE 105x50 mm graduated each 10 mm with

brass spacer 5 mm to measure the diameter of the soil
sample to 3 mm ± 0.5 according to NF P94-051
S179 GLASS PLATE 500x500x10 mm

S176

S176
LINEAR SHRINKAGE
STANDARD: BS 1377:2
Mould to produce a specimen of 140 mm long x 12.5 mm radius.
This test covers the determination of linear shrinkage of soils and
indicates the plastic properties of soils with a low clay content. S179
S178-06
Weight: 500 g approx.

Tel: +44 (0) 1442 402770

 E: [email protected]

482 RETURN TO HOMEPAGE

SECTION S | SOIL

CONE PENETROMETER METHOD FOR:

LIQUID LIMIT DETERMINATION

STANDARDS: CEN ISO/TS 17892-12 | BS 1377:2 | NF P94-052-1
The test is based on the relationship between the moisture content at which clay soils pass from a plastic to a liquid state.
This value is obtained from the penetration capacity of the standard cone allowed to free fall into the sample for a period of 5 seconds.
SHEAR STRENGTH DETERMINATION
STANDARD: CEN ISO/TS 17892-06
The cone penetrometer is also suitable to measure the shear undrained strength of undisturbed and reconstituted soil samples as per
CEN ISO/TS 17892-06 Standard.

B057-02

S166 KIT

S165 KIT

MODELS

S165 KIT S166 KIT

CONE DIAL PENETROMETER SEMIAUTOMATIC CONE DIAL PENETROMETER
The cone penetrometer consists of: Basically structured as mod. S165KIT, but equipped with a magnetic
- Aluminium base with levelling screws and spirit level. controller device with electronic digital programmable timer that
- Chromed vertical rod with micrometric vertical displacement automatically releases the plunger head and ensures free falling of
device. the cone during the 5-seconds test.
- Dial gauge 150 mm diameter, graduated in 360°, division 0.1 mm Supplied complete.
- Slider, brass made, with free fall, stop and release push button,
Power supply: 230V 1ph 50-60Hz 200W
automatic zero set.
Dimensions: 220x280x410 mm
- Stainless steel penetration test cone 35 mm long, 30° angle
Weight: 15 kg approx.
- Weight 20 g
- Two brass cups Ø 55x35 mm and 70x45 mm
Dimensions: 220x170x410 mm
Weight: 13 kg approx.

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 483

SECTION S | SOIL

B057-02

S165-02 KIT
S165-01 KIT
S165-01 KIT ACCESSORIES for S165 KIT, S166 KIT, S165-01 KIT, S165-02 KIT
CONE DIGITAL PENETROMETER
The cone penetrometer consists of: S166-03 TEST GAUGE, to check the condition of the cone point
- Aluminium base with levelling screws and spirit level. 30° angle.
- Chromed vertical rod with micrometric vertical displacement B057-02 MIRROR, to facilitate the height adjustment of the cone.
device. S166-04 TEST CONE 60° angle and 60 g weight (liquid limit and
- Digital readout of the penetration values. shear strength tests).
- Readings in mm and inch, with 0.1 mm resolution. LCD 5 digits
display, with zero set in any position. S166-05 TEST GAUGE, to check the condition of the cone point
Power: 1.5V battery. 60° angle.
- Slider, brass made, with free fall, stop and release push button, S166-06 WEIGHT, 320g to be added to the cone 30° angle, to get
automatic zero set. a total weight of 400 g (shear strength test).
- Stainless steel penetration test cone 35 mm long, 30° angle. V122-08 SAMPLE CUP, aluminum, Ø 55 mm by 40 mm deep, to
- Weight 20 g meet BS 1377:2 Specification
- Two brass cups Ø 55x35 mm and 70x45 mm
Dimensions: 220x170x410 mm
SPARES for S165 KIT, S166 KIT, S165-01 KIT, S165-02 KIT
Weight: 13 kg approx.
S166-01 Test cone 35 mm long and 30° angle.
S166-02 Weight 20 g to be added to the cone 30° angle, to get
S165-02 KIT
a total weight of 100 g
SEMIAUTOMATIC CONE DIGITAL PENETROMETER
V122-05 Brass cup Ø 55x35 mm
Basically structured as mod. S165-01 KIT, but equipped with a
V122-06 Brass cup Ø 70x45 mm
magnetic controller device with electronic digital programmable V122-06
timer that automatically releases the plunger head and ensures free V122-05
falling of the cone during the 5-seconds test. S166-06
Supplied complete. S166-02
Power supply: 230V 1ph 50-60Hz 200W
Dimensions: 220x280x410 mm
Weight: 15 kg approx. S166-04
S166-01 S166-03
S166-05

Tel: +44 (0) 1442 402770

 E: [email protected]

484 RETURN TO HOMEPAGE

SECTION S | SOIL

PROCTOR TEST MOISTURE-DENSITY RELATIONSHIP

STANDARDS: EN 13286-2 | ASTM D558, D698, D1557 | AASHTO T99, T134, T180 | BS 1377:4, 1924:2
CNR N° 69 | NF P94-078, P94-093, P98-231-1 | DIN 18127

PROCTOR MOULDS
Used for determining the relationship between the moisture content and density of compacted soils. Steel made, complete with mould body,
collar and base; plated against corrosion. Different proctor mould models are available according to the various international Standards in use.

Models Description Standards Int. diameter Body height Volume Weight

Proctor Mould mm mm ml kg
S185 Standard ASTM | AASHTO | NF | CNR 101.6 116.4 944 4.5

S186 Modified ASTM | AASHTO | CNR 152.4 116.4 2124 10

S189 Split Standard ASTM | AASHTO | NF | CNR 101.6 116.4 944 5

S190 Split Modified ASTM | AASHTO | CNR 152.4 116.4 2124 10

S190-01 Modified NF 152 152 2758 10

S191 Standard BS 105 115.5 1000 5

S194 Standard EN 13286:2 comparable to DIN 100 ± 1 120 ± 1 942 9

S194-01 Modified EN 13286:2 comparable to DIN 150 ± 1 120 ± 1 2120 13

S194-03 Split Standard EN 13286:2 comparable to DIN 100 ± 1 120 ± 1 942 7.5

S194-04 Split Modified EN 13286:2 comparable to DIN 150 ± 1 120 ± 1 2120 12.5

S194-02 Large Size EN 13286:2 comparable to DIN 250 ± 1 200 ± 1 9817 32

Note:
Annex “A” of EN 13286-2:2010 (E) Standard, allows alternative moulds such as: S185, S186, S189, S190, S190-01, S191, that have cheaper
prices. It is intended that these alternatives will be deleted at the next EN revision.

S194-02

S194-01

S185...S191
S194
S194-04

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 485

SECTION S | SOIL

PROCTOR RAMMERS
Used to compact the soil sample into the mould. The spherical hand knob is from bakelite with metal screw and protection ring nut; guide
sleeve with vent holes. The rammers are steel made, plated against corrosion, available in different models according to the various International
Standards in use. In alternative to the rammers the automatic compactor mod. S199 (see p. 000) can be used.

Models Description Standards Diameter Fall Rammer Total

mm height weight weight
mm kg kg
S187 Standard ASTM | AASHTO 50.8 304.8 2.495 5
Proctor rammer CNR | NF
S187-01 Standard EN 13286:2 50 ± 0.5 305 ± 3 2.5 ± 0.02 5
Proctor rammer comparable to BS
S188 Modified ASTM | AASHTO 50.8 457.2 4.536 8
Proctor rammer CNR | NF
S188-01 Modified EN 13286:2 50 ± 0.5 457 ± 3 4.5 ± 0.04 8
Proctor rammer comparable to BS
S188-02 Proctor rammer EN 13286:2 125 ± 0.5 600 ± 3 15 ± 0.04 23
Large Size

STEEL PLATE (COMPACTION DISK)

STANDARDS: EN 13286:2 | DIN 18127
Used to compact the EN moulds, it is supplied complete with
T handle, plated against corrosion.

MODELS S188-02

S194-09
PLATE, Ø 99.5 mm thickness 10 mm
S194-10
PLATE, Ø 149.5 mm thickness 10 mm
S194-11
PLATE, Ø 249.5 mm thickness 20 mm

S188-01

S194-11

S194-10

S194-09 S187

CUTTING COLLAR
Coupled to the Proctor mould body, it gets easier the soil sampling

MODELS

S185-01 Diameter 4” S114

S200-09 Diameter 6”
S114
UNIVERSAL EXTRUDER for moulds Ø 100, 150 mm; 4”, 6”
S200-09 Technical details at p. 000

Tel: +44 (0) 1442 402770

 E: [email protected]

486 RETURN TO HOMEPAGE

SECTION S | SOIL

S199
AUTOMATIC, PROGRAMMABLE PROCTOR | CBR COMPACTOR
WITH MICROPROCESSOR HIGH PERFORMANCE
STANDARDS: EN 13286-47 | ASTM D698, D1557, D1883
AASHTO T99, T180, T193 | BS 1377:4, 1990, 1994
NF P94-093, P94-066 | DIN 18127
UNE 7365, 7255, 103-501-94 | CNR UNI 10009
CNR N. 29, 69 | DUTCH RAW | AS 1289 and most
International Standards.

Designed to compact Proctor and CBR specimens, it ensures an

extremely uniform compaction degree, granting reliable and repeat-
able test results.

The microprocessor software allows to select and perform different

compaction cycles in a fully automatic system, by strictly meeting
the mentioned International Standards.

The blows are automatically distributed as requested by the

selected Standard, with turntable rotation and rammer displacement
through photoelectric cell sensors and microprocessor. Top quality
components and high accuracy mechanical workings grant very
long life also under intensive utilisations.

The digital control panel is separate from the machine and it can be
fixed to the wall or mounted on a bench.
The high resolution graphic display (blue negative) 320x240 pixels
visualizes selected Standard, total number of blows, effected and
remaining ones to end the test, and execution of each layer.

The compactor is easy to use, friendly menu driven, versatile, of

simple and practical maintenance.
S199 with mould
and rammer
The user can select and memorize up to 10 personalized test
cycles, that can be later on modified or replaced by other ones.
This is a very important function, because it allows to update the
Compactor to new Standards, or any Standard not included in the
microprocessor, or for research purposes. NEEDED ACCESSORIES

The original lift system of the rammer can be selected at 12” or 18”, S199-06 STANDARD RAMMER Ø 50 ± 0.2 mm
or at 300 or 450 mm, granting a correct and constant fall height. and 2500 ± 10 g weight
Rammer drop speed: 1 blow each 2 seconds. S199-07 MODIFIED RAMMER Ø 50 ± 0.2 mm
and 4535 ± 5 g weight
The compactor accepts moulds having Ø 4” and 6”, 100 and Conforming to: EN 13286-47 | BS 1377:4 | DIN 18127
150 mm, both Matest made or from other producers, thanks to its UNE 7255, 7365, 103-501-94 Standards.
universal mould fixing system. OR:
S199-08 STANDARD RAMMER Ø 50.8 ± 0.13 mm
The machine is supplied without rammers to be ordered separately and 2491,25 ± 1.25 g weight
and selected according to the desired Standard (rammers are inter- S199-09 MODIFIED RAMMER Ø 50.8 ± 0.13 mm
changeable). and 4537 ± 3 g weight
Not sellable in CE markets Conforming to: ASTM D558, D559, D698, D1557, D1883
(see accessory: safety guards mod S199-11) NF P94-066/93 | CNR UNI 10009
Power supply: 230V 1ph 50Hz 500W CNR N. 69 | ASHTO T99, T180, T193
Dimensions: 610x470xh1710 mm OR:
Weight: 165 kg approx. S199-13 STANDARD RAMMER, Ø 50 ± 0.4 mm
and 2700 ± 10 g weight
S199-14 STANDARD RAMMER, Ø 50 ± 0.4 mm
S199-07
and 4900 ± 10 g weight
S199-06 Conforming to: AS 1289 (Australian) Standard.

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 487

SECTION S | SOIL

AUTOMATIC PROCTOR | CBR COMPACTOR

TECNOTEST MODEL
A selector switch enables the operator to choose type of compaction
required (circular blow pattern for 4” or 100mm specimen moulds
and double concentric circles for 6” or 150 mm specimen moulds).
The number of blows is preset on the electronic microprocessor-based
control panel.
The machine is designed for long-term operation and has built-in
safety features (to CE Standards) to prevent it from being operated
without the unbreakable transparent safety guard.
Thanks to its compact height design, the compactor is recommended
for mobile laboratories.
Power supply: 230V 1ph 50Hz
Dimensions: 1760x590x400 mm
Test screen Weight: 260 kg approx.

ACCESSORIES MODELS

S199-11 SAFETY GUARDS to CE Directive. S199T AUTOMATIC COMPACTOR

If the door is opened when the Compactor is working, it STANDARDS: ASTM D698, D1557, D1883 | CNR N. 69 | CNR UNI 10009
stops automatically. Complete with rammer diameter 2” and interchangeable weights of
As alternative: 5.5 and 10 lbs. Height of rammer drop adjustable: 12” or 18”

S199-12 SOUNDPROOF SECURITY CABINET, steel made with S199T1 AUTOMATIC COMPACTOR
microswitch, complying to CE Safety Directive, lined with STANDARD: EN 13286-2
sound-proofing material for noise reduction. If the door Complete with rammer diameter 50 mm and interchangeable
is opened while the Compactor is working, it automati- weights of 2.5 and 4.5 kg
cally stops. Height of rammer drop adjustable: 305 or 457 mm
Dimensions: 740x730x1900 mm S199T2 AUTOMATIC COMPACTOR
Weight: 80 kg approx. STANDARDS: BS 1377, 1924
Complete with rammer diameter 50 mm and interchangeable
SPARES weights of 2.5 and 4.5 kg
Height of rammer drop adjustable: 300 or 450 mm
S198-22 Calibrated rod holding the rammer.
S198-23 Kit of two devices fixing the mould to the table.
NEW

S199 + S199-12 with accessories S199T

Tel: +44 (0) 1442 402770

 E: [email protected]

488 RETURN TO HOMEPAGE

SECTION S | SOIL

CALIFORNIA BEARING RATIO - CBR

STANDARDS: EN 13286-47 | EN 13286-4 | ASTM D1883 | AASHTO T193 | CNR UNI 10009 | UNE 103-502
NF P94-078, P94-093, P98-231-1 | BS 1377:4, 1924:2
This method has been developed by the California State Highway Department, and is now accepted by almost all the International Standards in
force. The test is aimed to the evaluation of the bearing capacity of soil for flexible pavement design in road construction. The compaction test
can be performed both with the manual rammers and the automatic compactor mod. S199.

S201-05

S200-01... CBR SET TO ASTM, AASHTO, CNR/UNI, UNE STANDARDS

S201... CBR SET TO NF STANDARDS

S202... CBR SET TO BS, EN 13286-4 STANDARDS

The CBR equipment, steel

made and plated against
corrosion is available in
different versions according
to the various Standards in
force.

S203... CBR SET TO EN 13286-47 STANDARD S114

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 489

SECTION S | SOIL

Description Standards
CALIFORNIA BEARING RATIO ASTM D1883 EN NF P94-078 EN 13286-4
Ordering info CNR UNI 1009 13286-47 NF P94-093 BS 1377:4
UNE 103-502 NFP98-231-1 BS 1924:2
AASHTO T193
CBR mould complete with collar and perforated base:
Ø 6” (152.4 mm) x 7” (177.8 mm) height S200-01
Ø. 150 mm x 120 mm height S203
Ø 152 mm x 152 mm height S201
Ø 152 mm x 127 mm height S202
Split CBR mould with collar and peforated base:
Ø 6” (152.4 mm) x 7” (177.8 mm) height S200-13
Ø 150 mm x 120 mm height S203-01
Ø 152 mm x 152 mm height S201-01
Solid base plate for CBR mould S200-12 S194-15 S202-03 S202-03
Perforated base plate for CBR mould S200-10 S194-14 S202-10 S202-10
Filter screen, stainless steel Ø 149 mm
mesh 0.150 mm (ASTM n° 100) S200-02 S200-02 S200-02 S200-02
Spacer disc with “T” handle:
Ø 5 15/16” (150.8 mm) x 2.416” (61.4 mm) height S200-03
Ø 149.5 mm x 36 mm height S194-21
Ø 151 mm x 25.4 mm height S201-02
Ø 151 mm x 36 mm height S201-06
Ø 150 mm x 50 mm height S202-07
Perforated (sweel) plate with adjustable stem S200-04 S194-23 S200-04 S200-04
Plein swell plate S194-24
Tripod (dial gauge support) S200-05 S194-26 S200-05 S200-05
Dial gauge10 mm range, 0.01 mm subd. S376 S376
Dial gauge 25 mm range, 0.01 mm subd. S377 S377
Annular surcharge weight 2270 g S200-07
Annular surcharge weight 2300 g S200-07
Annular surcharge weight 2000 g S202-08 S202-08
Slotted surcharge weight 2270 g S200-08
Split surcharge weight 2300 g S201-04
Split surcharge weight 2000 g S202-09 S202-09
Cutting edge S200-09 S200-09 S200-09
Compaction rammer:
Ø 50.8 mm fall height 457.2 mm, weight 4.54 kg. S188
Ø 50 mm fall height 457.2 mm, weight 4.54 kg. S188-01 S188-01 S188-01
Straight edge 300x30x3 mm S200-11 S200-11 S200-11 S200-11
Straight edge, cutting rim, 300x30x3 mm S200-06 S200-06 S200-06 S200-06
Filter paper Ø 150 mm (pack of 100) S200-14 S200-14 S200-14 S200-14
Soaking tank 600x400x400 mm S201-05 S201-05 S201-05 S201-05
Universal extruder (see p. 000) S114 S114 S114 S114

Tel: +44 (0) 1442 402770

 E: [email protected]

490 RETURN TO HOMEPAGE

SECTION S | SOIL

S196N
CLEGG HAMMER - IMPACT SOIL TEST
STANDARD: ASTM D5874-02
High quality genuine Clegg Impact Soil Tester manufactured under
license to Dr. Clegg Pty Ltd (the original inventors).
This apparatus is used to obtain an indication of the degree of
compaction of soil. Recorded valves can be directly correlated to the
CBR test method. User can quickly enable/disable the readout unit
to calculate the 4th drop %CBR following Dr. Clegg’s revised and
updated equation with inter-drop CIV check TREND algorithm.

MAIN FEATURES

Well-proven and stable components.

Easy to use, no set-up is required.
S196N
Back lit highly readable alpha numeric display.
Optionally fitted Bluetooth with PC Software to allow
data transfer of CIV, %CBR, time and data of up to
10000 drop tests.

Lightweight and sturdy aluminum framed transit and storage case

is provided. S197-01N
Dimensions: 710x130x130 mm
Weight: 6.2 kg approx.
S197-12

S197N
VIBRATING COMPACTION HAMMER
STANDARDS: EN 12697-9, 12697-10, 12697-32, 13286-4
BS 1377:4 | BS 1924:2
It provides an alternative method for the compaction of soil samples B097-12
S200-01 B097-11
in the determination of dry density/moisture content relation (called
Proctor), unconfined compressive strength of stabilized soils and
CBR tests. This hammer is also used for the compaction of asphalt
in the percentage refusal density (see p. 00) and for compacting
concrete cube or beam samples.
Supplied without tampers and support frame which must be ordered
separately.
S197N
Power supply: 230V 1ph 50-60Hz 930W
Dimensions: 105x430x270 mm
Weight: 7 kg approx.

ACCESSORIES

S197-01N SUPPORTING FRAME for vibrating hammer.

The sliding mass has a total weight (including hammer
and tamping foot) of 37 kg as requested by EN Spec.
Steel made, plated against corrosion.
Dimensions: 500x320x1100 mm COMPRESSIVE STRENGTH OF UNBOUND, HYDRAULICALLY BOUND
Weight: 75 kg approx. AND SOIL-CEMENT MIXTURES
STANDARDS: EN 13286-41, EN 12390-4
B097-11 SMALL TAMPING FOOT, 102 mm diameter.
Complete with shank. A compression machine with suitable measuring range (0-250/500
kN) is used for compression tests on soil-cement cylindrical mixture
B097-12 CBR AND PROCTOR LARGE TAMPING FOOT, specimens. The cement (see p. 000) or concrete (see p. 000...000)
146 mm diameter. Complete with shank. machines are suitable to perform this test.

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 491

SECTION S | SOIL

STRENGTH OF STABILIZED SOIL DETERMINATION

STANDARDS: EN 13286-53 | NF P94-100 | NF P98-230-2 | BS 1924 :2
Used to prepare specimens bound with cementitious binders or aggregate mixes for determination of the Unconfined compressive strength of
fine and medium grained soils. Made of plated steel.

MODELS

S195-01 Mould Ø 50 by 122 mm to obtain specimen dia. 50x50 S195-22 Collecting cylinder Ø 106 by 210 mm
mm high of fine and medium grained soil (NF)
S195-11 Set of 2 displacing collars Ø 50 by 5 mm
S195-02 Mould Ø 50 by 172 mm to obtain specimen dia. 50x100
mm high of fine and medium (EN, BS) and of coarse S195-06 Set of 2 displacing collars Ø 50 by 6 mm
grained soil (NF)
S195-12 Set of 2 displacing collars Ø 50 by 8.33 mm
S195-15 Mould Ø 100 by 242 mm to obtain specimen dia.
100x100 mm high of coarse grained soil (EN, BS) S195-23 Set of 2 displacing collars Ø 50 by 10 mm

S195-20 Mould Ø 100 by 342 mm to obtain specimen diameter S195-07 Set of 2 displacing collars Ø 50 by 12.5 mm
100x200 mm high of coarse grained soil (EN, BS)
S195-24 Set of 2 displacing collars Ø 50 by 16.66 mm
S195-03 Base and upper piston Ø 50 by 36 mm
S195-08 Set of 2 displacing collars Ø 50 by 25 mm
S195-16 Base and upper piston Ø 100 by 71 mm
S195-13 Set of 2 displacing collars Ø 100 by 10 mm
S195-04 Penetration and demoulding piston Ø 50 by 125 mm
S195-14 Set of 2 displacing collars Ø 100 by 16.66 mm
S195-05 Penetration and demoulding piston Ø 50 by 175 mm
S195-25 Set of 2 displacing collars Ø 100 by 20 mm
S195-17 Penetration and demoulding piston Ø 100 by 245 mm
S195-19 Set of 2 displacing collars Ø 100 by 25 mm
S195-21 Penetration and demoulding piston Ø 100 by 345 mm
S195-27 Set of 12 displacing collars Ø 100 by 33.33 mm
S195-09 Collecting cylinder Ø 56 by 60 mm
S195-28 Set of 2 displacing collars Ø 100 by 50 mm
S195-10 Collecting cylinder Ø 56 by 110 mm

S195-18 Collecting cylinder Ø 106 by 110 mm

S195-01...S195-28

Tel: +44 (0) 1442 402770

 E: [email protected]

492 RETURN TO HOMEPAGE

SECTION S | SOIL

S131 KIT S210 KIT

UNCONFINED COMPRESSION TESTER CBR LOADING MACHINE
STANDARDS: ASTM D2166 | AASHTO T208 | BS 1377:7 HAND OPERATED, FIELD MODEL
This hand-operated tester, utilized both on site and in laboratory, STANDARDS: EN 13286-47 | ASTM D1883 | AASHTO T193
applies the load by a handwheel and strength is read on a proving BS 1377:4 | NF P94-078 | CNR UNI 10009
ring 200 kg. capacity.
The load is applied through a mechanical jack with handwheel.
The apparatus can test samples up to Ø 80 mm x 200 mm height .
The upper beam can be adjusted in height.
The S131KIT tester comprises:
The S210KIT machine comprises:
S221 Conversion frame
S221 Conversion frame
S221-01 Mechanical jack 50 kN capacity
S221-01 Mechanical jack 50 kN
S370-02 Load ring 2 kN capacity capacity
S131-11 Upper+lower compression platens with accessories S370-10 Load ring 50 kN capacity
S376 Dial gauge 10x0.01 mm S212-01 CBR penetration piston
S212-03 Dial gauge holder S376 Dial gauge 10x0.01 mm
Dimensions: 380x460x1380 mm S212-03 Dial gauge holder
Weight: 68 kg approx.
Dimensions: 420x370x1180 mm
Weight: 65 kg approx.

S210 KIT
Note:
The machines described in this page include some common com-
ponent (like for ex. the mechanical jack mod. S221-01).
It is therefore possible to combine these components for different
machines, with some economical advantage.

S131 KIT
S220 KIT
FIELD CBR TEST SET
STANDARDS: BS 1377:9 , 1924:2 | ASTM D4429
CNR UNI 10009
Used to determine quickly and efficiently the bearing capacity of
soils on road constructions, foundations, road subgrades etc.
The S220 KIT tester comprises:
S221-01 Mechanical jack 50 kN capacity
S370-09 Load ring 40 kN capacity
S212-01 CBR penetration piston
S377 Dial gauge 25x0.01 mm
S212-03 Dial gauge holder
S220-01 Datum bar 1400 mm long; slotted surcharge
weights 4.5 and 9 kg and annular 4.5 kg; set of
extension rods: 2x100 mm, 1x300, 600, 1000 mm;
accessories; wooden carrying case.
Weight: 70 kg approx. S220 KIT

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 493

SECTION S | SOIL

CALIFORNIA BEARING RATIO TESTING MACHINES - CBR

STANDARDS: EN 13286-47 | ASTM D1883 | BS 1377-4 | AASHTO T193 | CNR UNI 10009 | NF P94-078
Used to load the penetration piston into the soil sample at a constant rate of 1.27 mm/min, and to measure the applied loads and piston’s
penetrations at determined intervals.
Matest proposes a wide range of machines: hand operated, motorized, dual speed, universal multispeed; load measurement by load ring, or by
electric load cell and digital unit with X/Y graphic recorder of load/penetration through RS 232 port to PC.

S209 KIT S211 KIT

CBR LOADING MACHINE CBR LOADING MACHINE, 50 KN
HAND OPERATED, LABORATORY MODEL MOTORIZED SPEED RATE: 1.27 MM/MIN
Load is applied through a meckanical jack and handwheel. Load is applied through a screw jack driven by an electric motor at
Upper beam can be adjusted in height. a costant penetration rate of 1.27 mm/min (ASTM, BS, EN Spec.)
Foreseen of fast approach device of the base plate. achieved by a built in gear box and assured also under load.
The S209KIT CBR machine comprises: Upper beam can be adjusted in height.
S209-01 CBR laboratory frame Foreseen of fast approach device of the base plate and electric end
of stroke switches of the load plate to save the machine from wrong
S212-01 CBR penetration piston
manipulations.
S370-10 Load ring 50 kN capacity
The S211KIT CBR machine comprises:
S376 Dial gauge 10x0.01 mm
S211-10 CBR motorized frame
S212-03 Dial gauge holder
S212-01 CBR penetration piston
Dimensions: 430x380x1180 mm S370-10 Load ring 50 kN capacity
Weight: 80 kg approx.
S376 Dial gauge 10x0.01 mm
S212-03 Dial gauge holder
Power supply: 230V 1ph 50Hz 750W
Dimensions: 430x380x1180 mm
Weight: 98 kg approx.

S209 KIT

ACCESSORIES

S210-02 CBR RATE INDICATOR

Used to apply the correct rate of
1.27 mm/min penetration to hand
operated CBR machine S209 KIT.
Power supply: 230V 1ph 50Hz
S211 KIT

S210-02 S374-01 ELECTRIC DEVICE FOR AUTOMATIC STOP of the CBR

S374 BRAKE DEVICE, it holds the max. applied load on the dial machine when reaching the max. capacity load.
gauge of the load ring, with manual zero setting. To prevent any overload damage this device is mounted
Suitable for S209 KIT and S211 KIT machines. on the proving ring of the S211 KIT machine.

Tel: +44 (0) 1442 402770

 E: [email protected]

494 RETURN TO HOMEPAGE

SECTION S | SOIL

S212N S213-05N
UNIVERSAL MULTISPEED LOAD FRAME 50 KN CBR/MARSHALL 3 SPEEDS FRAME 50 KN
DIGITAL, TOUCH-SCREEN The frame is provided of three fix speed ranges, easily selectable by
This motorized machine with electronic digital touch-screen con- a frequency changer (inverter) activated by an electric switch:
trolled by microprocessor, is suitable to perform all the tests where 1.00 mm/min. for CBR tests (Australian and old BS Standards)
the requested speed rate is within: 1.27 mm/min. for CBR tests
0.05 to 63 mm/min with max. load of 50 kN 50.8 mm/min for Marshall tests.
It can therefore perform: Upper beam can be adjusted in height.
- Unconfined test with rate of 0.635 mm/min. Foreseen of electric end of stroke switch of the load plate to save
- CBR test with rate of 1.27 and 1 mm/min. the machine from wrong manipulations.
- Marshall test with rate of 50.8 mm/min. Supplied without load ring and
- Splitting tensile test on Marshall specimens. accessories which have to be
- Quick Triaxial (with trixial cell and suitable accessories) ordered separately.
The speed rate is infinitely variable, easily and promptly selected. Power supply:
Graphic display ¼ VGA color Touch-Screen. 230V 1ph 50-60Hz 750W
Time/date and language selection (English, French, German, Span- Dimensions:
ish, Italian, Polish). 450x400x1200 mm
Symbols of pushbuttons functions. Weight: 130 kg approx.
Foreseen of electric end of stroke switch of the load
plate to save the machine from wrong manipulations.
Upper beam can be adjusted in height.
Supplied without load ring and accessories which
have to be ordered separately.
Power supply: 230V 1ph 50-60Hz 750W
Dimensions: 480x450x1400 mm
Weight: 140 kg approx.
NEW
S213-05N
with accessories for CBR test

ACCESSORIES for S212N

and S213-05N frames
CBR test
S212-01 Penetration piston
S370-10S Load ring 50kN with electric stop safety device
S374 Brake device to hold max. load
S376 Dial gauge 10x0.01 mm
S212-03 Dial gauge holder
MARSHALL test
S212-05 Load piston
B046N Stability mould
B047 Flow meter
B047-01 Dial gauge for flow meter
S370-08S Load ring 30kN with electric stop safety device
S374 Brake device to hold max. load
UNCONFINED test
S212-08N Upper + lower compression plates, Ø 100 mm
+ distance piece with rod
S212-03 Dial gauge holder
S376 Dial gauge 10x0.01 mm
S370-02S Load ring 2kN with electric stop safety device
S212N with accessories for CBR test S374 Brake device to hold max. load

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 495

SECTION S | SOIL

MULTIFUNCTION TESTING FRAMES

CBR
THREE SPEEDS
UNIVERSAL MULTISPEED
COMBINED WITH “CYBER-PLUS EVOLUTION”, COMPUTERIZED TOUCH-SCREEN DIGITAL DISPLAY SYSTEM

TECHNICAL SPECIFICATIONS
The frame is the same as for the previous load frames (mod. S211 KIT to S213-05N), but the load is measured by an electric 50kN cell with
high precision strain transducers. The deformation (flow) is measured by a displacement transducer 50 mm stroke and ± 0.1% indipendent
linearity.
The “CYBER-PLUS EVOLUTION” computerized multichannel digital display system (technical details: see mod. B044N-SET at p. 000, Hardware
technical details at p. 00), measures and displays at the same time the load (stability) in kN and the deformation (flow) in mm with pick hold fea-
tures and possibility to print certificates and graphics directly on a laser printer via USB or to transfer them to PC via Ethernet.

AVAILABLE MODELS

S216 KIT S214-05N KIT

CBR DIGITAL COMPUTERIZED MACHINE CBR/MARSHALL 3 SPEEDS LOAD FRAME
SPEED RATE: 1.27 mm/min DIGITAL, COMPUTERIZED
Technical details of the frame: see mod. S211 KIT, p. 000 The frame is provided of three fix speed ranges, easily selectable by
SUPPLIED COMPLETE except the software (see next page mod. S218N). an electric switch:
1.00 mm/min. for CBR tests (Australian and old BS Standards)
1.27 mm/min. for CBR tests
50.8 mm/min for Marshall tests.
Technical details of the frame: see mod. S213-05N, p. 000
Supplied complete with “Cyber-Plus Evolution” system, load cell and
displacement transducer, but without accessories and Software for
CBR and Marshall tests, to be ordered separately (see accessories
at next page).

NEW

S216 KIT + CBR mould

S214-05N KIT + MARSHALL accessories

Tel: +44 (0) 1442 402770

 E: [email protected]

496 RETURN TO HOMEPAGE

SECTION S | SOIL

S215A
UNIVERSAL MULTISPEED LOAD FRAME
DIGITAL, TOUCH-SCREEN, COMPUTERIZED
Comprising:
S212N Universal multispeed load frame 50 kN, touch-screen. Technical spec.: see p. 000
S212A Acquisition and data processing system up to 8 analogical/digital channels for load cells and transducers. Graphic and numbers
visualization, processing and printing of the test results.
Technical spec.: see B044N Cyber-plus 8 Evolution Touch-Screen, next page.
S337-34 Load Cell 50 kN capacity, complete with cable and connector.
S336-14 Linear Displacement Transducer 50 mm stroke, complete with cable and connector.
S305-05 Mounting device of the coupling pliers.
S335-15 Coupling pliers to hold the transducer.
Supplied without accessories for CBR, Marshall, Unconfined tests
and Software, to be ordered separately (see accessories).

The Universal Multispeed tester, is the ideal solution to perform the

following tests :

CBR (California Bearing Ratio)

UNCONFINED COMPRESSION
QUICK TRIAXIAL
MARSHALL

Detail of 8 channels

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 497

SECTION S | SOIL

S215A with CBR accessories

ACCESSORIES for the 3 speeds and the multispeed load SOFTWARES for the frames combined with
frames, mod. S214-05N KIT and S215A to perform “Cyber-Plus Evolution” System
CBR tests S218N SOFTWARE UTM2 Licence for CBR Test
S212-01 PENETRATION PISTON STANDARDS: EN 13286-47 | CNR UNI 10009 | ASTM D1883
BS 1377 | NF P94-078 | AASHTO T193
MARSHALL tests
S212-05 LOAD PISTON S218-01N SOFTWARE UTM2 Licence for UNCONFINED test
B046N STABILITY MOULD, cast aluminium alloy STANDARDS: ASTM D4123 | EN 12697-12, 12697-23
B043-01N SOFTWARE UTM2 Licence for MARSHALL test
UNCONFINED test
STANDARDS: EN 12697-34 | ASTM D1559, D5581, D6926
S212-08N UPPER + LOWER COMPRESSION PLATES,
Ø 100 mm + distance piece with rod B043-02N SOFTWARE UTM2 Licence for TENSILE SPLITTING test
STANDARDS: EN 12697-23 | ASTM D6931
QUICK TRIAXIAL TEST (only with S215A frame)
Description and technical details of Software UTM2: see p. 00
S337-31 STRAIN LOAD CELL 2.5 kN capacity
S205-11 LOADING PISTON WITH BALL
S305 TRIAXIAL CELL + accessories
S218-02N SOFTWARE for quick triaxial test
STANDARDS: ASTM D2850 | BS 1377

Tel: +44 (0) 1442 402770

 E: [email protected]

498 RETURN TO HOMEPAGE

SECTION S | SOIL

B044N-SET MAIN FEATURES

CYBER-PLUS 8 EVOLUTION TOUCH-SCREEN
Developed for the implementation and upgrading of any type of Acquisition and data processing system up to 8
existing machines (even not manufactured by Matest) applicable to: analogical/digital channels.
- Marshall mechanical load frame mod. B042 KIT.
Remote control through PC and UTM2 software.
- CBR/Marshall 3 speeds load frame mod. S213-05N.
Graphic display 1/4 VGA color Touch-Screen.
- CBR loading machine motorized mod. S211 KIT.
Instant display of load and deformation.
Suitable to perform the following tests:
Automatic correction of the axis origin and automatic
- MARSHALL: EN 12697-34 | ASTM D6926, D5581, D1559
calculation of all the results.
CNR N. 30 | NF P98-251-2 | BS 598 :107
AASHTO T245 Safety switch-off at max reached load and/or
- INDIRECT TENSILE TEST: EN 12697-23, EN 12697-12 deformation.
ASTM D6931 | AASHTO T283
- DETERMINATION OF THE WATER SENSIBILITY OF BITUMINOUS
SPECIMENS: EN 12697-12
- CBR TEST: EN 13286-47 | CNR | UNI 10009 | AASHTO T193
ASTM D1883 | BS 1377:4 | NF P94-078.
- UNCONFINED TEST: ASTM D4123 | EN 12967-12, 12697-23
CNR N° 34

B044N SET

HARDWARE SPECIFICATIONS - Visualization of date and time.

- 8 indipendent channels available for the load cells or potentiomet- - Semi-automatic configuration and calibration of all transducers
rics transducers for load, or displacement measurements; connected.
- Stabilized power supply of the analogical channels: - 20 steps lining that can be set by the enduser.
5 Vcc and 3 Vcc;
- Automatic correction of the axis origin for CBR/Marshall tests.
- Analogue input: ± 20 mV and ± 5 V;
- Setting of all the parameters for test: alarms, zero threshold, end-
- Nominal resolution: 24 bit; test percentage, calculation parameters.
- Acquisition up to 200 readings for each channel; - Time/date and language selection (Italian, English, French,
- Safety discrete On/off output; German, Spanish, Polish).
- Graphic display ¼ VGA colour Touch-Screen; - Unlimited file for each type of test
- Time and calendar system. - Symbols of pushbuttons functions
- Informative messages (planning alarms, load cell and strain trans-
FIRMWARE SPECIFICATIONS ducer setting, etc.)
- Instant visualization of the load measured by an extensometric - Printing of the results on the incorporated thermal graphic printer
cell. (accessory C127N). Transfer and management via Ethernet of the
- Instant visualization of the deformation measured by 4 linear filed data or real-time.
displacement transducers. Hardware technical details: see p. 00
- Visualization of the graphic of the test.

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 499

SECTION S | SOIL

B044N-SET is composed of: B043-02N

B044N SOFTWARE UTM2 (Universal Testing Machine 2)
CYBER-PLUS 8 EVOLUTION Licence for INDIRECT TENSILE STRENGTH
Unit for data acquisition. STANDARDS: EN 12697-23 | ASTM D6931
Power supply: 230V 1F 50-60Hz.

S337-34
LOAD CELL
50kN capacity, with high precision strain transducers, complete
with cable and connector.

S336-14
LINEAR DISPLACEMENT TRANSDUCER
50 mm stroke, independent linearity ± 0.1% complete with cable
and connector.

All necessary accessories for fixing the load cell and transducer to
the test machine, are provided.
The system is calibrated ready to use and COMPLETE with a cali-
bration certificate.
Every item can be ordered separately.

ACCESSORIES

B043-01N
SOFTWARE UTM2 (Universal Testing Machine 2)
Licence for MARSHALL test
Data processing program for “X-Y STABILITY/FLOW”
STANDARDS: EN 12697-34 | ASTM D6926, D5581, D1559
BS 598:107 | NF P98-251-2

S218N
SOFTWARE UTM2 (Universal Testing Machine 2)
Licence for CBR Test
STANDARDS: EN 13286-47 | UNI CNR 10009 | ASTM D1883
BS 1377 | NF P94-078 | AASHTO T193
S218-01N
SOFTWARE UTM2 (Universal Testing Machine 2)
Licence for UNCONFINED Test
STANDARDS: EN 12697-12, 12697-23 | ASTM D4123

Description and technical details of Software UTM2: see p. 00

H009-01
PERSONAL COMPUTER, complete with LCD monitor 22”, keyboard,
mouse, connection cables, installation and setting up of the pur-
chased software.

C128
LASER PRINTER for test certificate and graphics printing with direct
connection to CYBER-PLUS 8.

Tel: +44 (0) 1442 402770

 E: [email protected]

500 RETURN TO HOMEPAGE

SECTION S | SOIL

S205N
UNITRONIC 50 KN NEW
UNIVERSAL MULTIPURPOSE TOUCHSCREEN COMPRESSION/FLEXURAL AND TENSILE FRAME FOR:
COMPRESSION / FLEXURAL TESTS, 50 kN MAX. CAPACITY LOAD
TENSILE TESTS, 25 kN MAX. CAPACITY LOAD (option mod. S205-05N)

With automatic load or displacement/deformation control, for

testing:
SOIL:
CBR (California Bearing Ratio)
UNCONFINED COMPRESSION
QUICK TRIAXIAL
ASPHALT:
MARSHALL
SPLITTING TENSILE
DIRECT SHEAR (Leutner) on the connection between bituminous
strata
AUTO SCB
CONCRETE:
FLEXURE ON BEAMS AND TILES
CEMENT:
FLEXURE on 40x40x160 mm specimens
COMPRESSION on cubes 40, 50, 70 mm
TENSILE on mortar briquettes (option mod. S205-05N)
METAL, PLASTIC, WIRES, ROPES, TEXTILES, PAPERS ETC.
TENSILE TESTS, 25kN max capacity load (option mod. S205-05N)
CLAY BLOCKS:
PUNCHING
ROCK AND STONES:
UNIAXIAL SPLITTING TENSILE

S205N / S205-05N with load cell

TECHNICAL FEATURES:
By using suitable devices, Unitronic tester, within the limits of its max. 50 kN capacity for compression/flexural and 25 kN for tensile (see model
S205-05N), performs compression, flexural, splitting tensile and direct tensile tests, with automatic load or displacement/deformation control.
The load is applied by a mechanical jack that is driven by a motor brushless with closed loop through optic encoder and controlled by a
microprocessor. Stroke electric end switches are applied to the load piston to save the machine from accidental handlings.
The two crossheads foresee couplings to fix the different test devices (see accessories). The stress is measured by an electric load cell; the
measurement and the displacement control of the crosshead is achieved by the electronic device incorporated into the machine.

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 501

SECTION S | SOIL

FIRMWARE TECHNICAL SPECIFICATIONS

Electronic control unit “Cyber-plus Evolution” with Touch-Screen Maximum compression capacity: 50kN
colour display, that runs like a standard PC based on Windows Maximum tensile capacity: 25kN (model S205-05N)
operating system for the management and analysis of the data,
Adjustable testing speed from 0.01 to 51mm/minute
test results, graphs.
Adjustable pace rate from 1 to 15000N/sec.
The Touch-Screen icon interface allows an easy set up of the
parameters and immediate execution of the test. Max. ram travel: 100 mm
The machine can be connected to a PC for remote test execution Daylight between columns: 380 mm
through suitable Software; the machine can in any case perform Max. vertical daylight: 850 mm
the tests without any external PC, because of the “Cyber-Plus” Unitronic 50 kN is supplied without accessories and software
grants performances like a PC. to perform the specific tests that must be ordered separetely (see
Direct connection to Intranet (connection to a LAN network) and accessories at next pages)
Internet to establish a remote communication and receive an
Power supply: 230V 1ph 50-60Hz 1500W
immediate diagnostic analysis from Matest technicians, or for
Dimensions: 500x450x1450 mm
updates of the software.
Weight: 130 Kg approx.
Unlimited memory storage with: 2 USB ports, 1 SD card slot.
RJ45 network connection
Possibility to select different languages.
Hardware technical details: see p. 00

UNITRONIC screen examples: CBR test UNITRONIC screen examples: main screen

S205-05N
UNITRONIC COMPRESSION | TENSILE

The Unitronic frame S205N is modified and improved to perform also tensile tests with max. capacity of 25 kN.

Note: this modification is possible only in MATEST factory.

Tel: +44 (0) 1442 402770

 E: [email protected]

502 RETURN TO HOMEPAGE

SECTION S | SOIL

S205N UNITRONIC 50 KN CAN PERFORM THE FOLLOWING TESTS:

CBR TEST MARSHALL TEST CEMENT COMPRESSION CONCRETE FLEXURE

QUICK TRIAXIAL SPLITTING TENSILE CEMENT FLEXURE CLAY BLOCKS PUNCHING

UNCONFINED COMPRESSION DIRECT SHEAR (LEUTNER) TENSILE TEST ON MORTAR TILE FLEXURE
BRIQUETTES

UNIAXIAL ROCK SPLITTING AUTOMATIC SCB SYSTEM TRANSVERSE / DEFORMATION TENSILE TEST ON METALS,
TENSILE TEST ON ADHESIVE PLASTIC, WIRES, TEXTILES ETC.

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 503

SECTION S | SOIL

S205N | S205-05N UNITRONIC, SPECIFIC APPLICATIONS

CBR: CALIFORNIA BEARING RATIO TEST UNCONFINED COMPRESSION TEST

STANDARDS: STANDARDS:
EN 13286 -47 ASTM D2166
ASTM D1883 BS 1377:7
BS 1377:4 AASHTO T208
AASHTO T193
NF P94-078 Test development with
CNR UNI 10009 displacement control.

Test development with

displacement control.

S205N Unitronic 50 kN S205N Unitronic 50 kN

S337-34 Strain gauge load cell, 50 kN capacity S337-31 Strain gauge load cell 2.5 kN capacity.
S337-51 Calibration process of load cell / Unitronic S337-51 Calibration process of load cell / Unitronic
S212-01 Penetration piston S212-08N Upper and lower compression platens Ø 100 mm with
S218N Software for CBR test accessories
S218-01N Software for Unconfined Compression test

S218N Software CBR test S218-01N Software unconfined test

QUICK TRIAXIAL TEST UNIAXIAL SPLITTING TENSILE TEST OF ROCK CORE SPECIMENS

STANDARDS: STANDARD:
ASTM D2850 ASTM D3667
BS 1377
Test development with
Test development with displacement control.
displacement control.

S205N Unitronic 50 kN S205N Unitronic 50 kN

S337-31 Strain gauge load cell 2.5 kN capacity S337-34 Strain gauge load cell 50 kN capacity
S337-51 Calibration process of load cell / Unitronic S337-51 Calibration process of load cell / Unitronic
S205-11 Loading piston with ball S212-05 Loading piston
S305 Triaxial cell with accessories E171 Compression device
S218-02N Software for QUICK TRIXIAL test

Tel: +44 (0) 1442 402770

 E: [email protected]

504 RETURN TO HOMEPAGE

SECTION S | SOIL

MARSHALL STABILITY TEST

STANDARDS:
EN 12697-34
ASTM D1559
D5581, D6926
AASHTO T245
BS 598 :107
NF P98-251-2

Test development with

displacement control.

File Marshall test

S205N Unitronic 50 kN
S337-34 Strain gauge load cell, 50 kN capacity
S337-51 Calibration process of load cell / Unitronic
S212-05 Loading piston
B046N Stability mould
B043-01N Software for Marshall test

SPLITTING TENSILE TEST

STANDARDS:
EN 12697-23,12
ASTM D6931
AASHTO T283 B043-01N Software Marshall test
CNR 134

Test development with

displacement control.

DIRECT SHEAR (LEUTNER) BETWEEN BITUMINOUS STRATA

STANDARD:
S205N Unitronic 50 kN ALP A StB T4
S337-34 Strain gauge load cell, 50 kN capacity
S337-51 Calibration process of load cell / Unitronic Test development with
S212-05 Loading piston displacement control.
B047-02 Splitting tensile device for samples Ø 4” and 6”
B047-04 Set of TWO displacement transducers with accessories
B043-02N Software for Splitting Tensile test

S205N Unitronic 50 kN
S337-34 Strain gauge load cell 50 kN capacity
S337-51 Calibration process of load cell / Unitronic
S212-05 Loading piston
B047-10 LEUTNER testing head for specimens Ø 150 mm
B047-11 Spacers for Ø 100 mm specimens with Leutner head
B043-03N Software for Marshall and Leutner tests

Direct shear test (LEUTNER) on the connection between bituminous

strata, carried out on asphalt cylinder specimens Ø 150 mm or
S043-02N Software splitting tensile test
100 mm obtained from road cores or on laboratory made specimens.

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 505

SECTION S | SOIL

AUTO SCB SEMI-CIRCULAR BEND

STANDARDS: B045-13 Loading piston

EN 12697-44 S336-15 Transducer type "B" travel: 10 mm
AASHTO TP124 B045-14 Coupling hardware
ASTM D8044 S335-15 Universal coupling pliers for transd./dial
B043-05N Software for auto-scb test

Test development with AASHTO TP124 | ASTM D8044

displacement control. B208 SCB frame
B254-02 Springs
B254-10 Roller support
S337-31(*) Load cell 2,5 kn capacity
B045-13 Loading piston
S336-15 Transducer type "b" travel: 10 mm
EN 12697-44 B045-14 Coupling hardware
B250-01 Basic indirect tensile (idt) jig, for 100-150 mm diameter S335-15 Universal coupling pliers for transd./dial
B254-01 Scb jig (requires basic idt jig) B043-05N Software for auto-scb test
B254-51 Pair of scb wear plates
S337-34 Load cell 50 kn capacity Note: for more details see p. 000.

COMPRESSION TEST ON MORTAR SPECIMENS (50KN MAX. LOAD) FLEXURAL TESTS ON MORTAR PRISM 40X40X160 MM

STANDARDS: STANDARDS:
EN 196-1 EN 196-1
EN ISO 679 ASTM C348
ASTM C109, C349 NF P15-451
NF P15-451 DIN 1164
BS 3892 EN ISO 679
DIN 1164
Test development with
Test development with displacement control.
displacement control.

S205N Unitronic 50 kN S205N Unitronic 50 kN

S337-34 Strain gauge load cell 50 kN capacity S337-32 Strain gauge load cell 10 kN capacity
S337-51 Calibration process of load cell / Unitronic S337-51 Calibration process of load cell / Unitronic
S212-05 Loading piston S212-05 Loading piston
E170 Compression device on portion of 40x40x160 mm E172-01 Flexure EN device for 40x40x160 mm specimens
specimens (available also to ASTM, see p. 000)
E163N Software for compression tests E164N Software for flexural tests

E163N Software for mortar compression E164N Software for mortar flexure

Tel: +44 (0) 1442 402770

 E: [email protected]

506 RETURN TO HOMEPAGE

SECTION S | SOIL

TENSILE TEST ON MORTAR BRIQUETTES “8” SHAPED TRANSVERSE/DEFORMATION TEST ON ADHESIVES FOR TILES

STANDARDS: STANDARD:
ASTM C190, C307 EN 12002
AASHTO T132
Test development with
Test development with load displacement control.
control.

S205-05N Unitronic Compression 50 kN / Tensile 25 kN S205N Unitronic 50 kN

S337-32 Tensile/Compression strain load cell 10kN capacity S205-14 Strain gauge load cell 500 N capacity
S337-51 Calibration process of load cell / Unitronic S337-51 Calibration process of load cell / Unitronic
S205-07 Tensile jaws “8” shaped for mortar briquette S205-13 Flexure device with lower bearers and upper loading
S205-08N Software for tensile test piston
E111 Briquette mould (see p. 000)

TWO POINT FLEXURAL AND TRANSVERSE TESTS PUNCHING TEST ON CLAY BLOCKS
ON CONCRETE BEAMS AND BENDING TEST METHOD
ON GLASS-FIBRE REINFORCED CONCRETE STANDARDS:
EN 15037-2, -3
STANDARDS: UNI 9730-3
EN 12390-5
EN 1170-4 Test development with
ASTM C78, C293 load control.

Test development with load

control for concrete beams
and displacement control
for bending test on
glass-fibre reinforce
cement.
S205N Unitronic 50 kN
S337-32 Strain gauge load cell 10 kN capacity
S205N Unitronic 50 kN S337-51 Calibration process of load cell / Unitronic
S337-34 Strain gauge load cell 50 kN capacity C093-11 Flexural punching device
S337-51 Calibration process of load cell / Unitronic S205-15 Holding beam for the punching device
S205-16 Two-point bending device to test glass-fibre reinforced C109-16N Software for punching test on clay blocks
cement. Rollers dimensions: Ø 40 by 310 mm long.
Lower rollers adjustable from 110 to 310 mm.
Upper rollers adjustable from 45 to 120 mm.
Weight: 20 kg approx
C109-11N Software for flexure tests on concrete beams

C109-11N Flexure: Outline of test data C109-16N

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 507

SECTION S | SOIL

MARSHALL STABILITY TEST

STANDARDS:
EN 12390-5, 491, 538
ASTM C78, C293
BS 1881:118

Test development with

load control.

S205N Unitronic 50 kN
S337-34 Strain gauge load cell, 50 kN capacity
S337-51 Calibration process of load cell / Unitronic
S205-18 Flexure device for centre point loading to test clay tiles and con-
crete beams dimensions 100x100x400(500) mm. Consisting of
lower beam with two bearers (one articulated) adjustable from
110 to 310 mm, and upper central articulated bearer fixed to the
load cell.Bearer dimensions: Ø 40 mm by 310mm long.
Weight: 20 kg approx C109-11N Software for flexural test on concrete beam
C109-11N Software for flexure tests

TENSILE TESTS ON METALS, PLASTICS, WIRES, TEXTILES ETC.

STANDARDS:
ASTM D2166
BS 1377:7
AASHTO T208

Test development with

load control.

S205-05NUnitronic Compression 50 kN / Tensile 25 kN

S337-36 Tensile strain load cell 25 kN capacity
S337-51 Calibration process of load cell / Unitronic
H005-11 Tensile heads (upper and lower)
S205-09 Coupling for tensile heads installation
H005-21 Flat seizing grips for flat specimens 1 - 10 mm thickness
by 25 mm max. width and round specimens Ø 3-5 mm
H005-31 “V” shape seizing grips for round specimens Ø 5-12 mm
H014-06 to H014-10 Extensometer, electronic, for tensile
deformation strength tests. (See p. 000)
H009N Software for visualisation in real time of load/ H009N
deformation, graphic, test certificate etc

At p. 000 you will find devices to test plastics, wires, ropes, flexural and bending tests and various models of extensometers. On request it is also
possible to equip the Unitronic frame S205-05N with devices for tensile tests of different materials, within the 25kN max. capacity load.

Note: Needed accessories listed above, are common for different tests. We recommend to check them when ordering, to avoid duplications.

Tel: +44 (0) 1442 402770

 E: [email protected]

508 RETURN TO HOMEPAGE

SECTION S | SOIL

S206N
UNITRONIC 200 KN
UNIVERSAL MULTIPURPOSE TOUCHSCREEN
COMPRESSION/FLEXURAL AND TENSILE FRAME FOR:
COMPRESSION / FLEXURAL TESTS, 200 kN MAX. CAPACITY LOAD
TENSILE TESTS, 50 kN MAX. CAPACITY LOAD

With automatic load or displacement/deformation control, for

testing:
SOIL:
CBR (California Bearing Ratio)
ASPHALT:
DURIEZ
MARSHALL
SPLITTING TENSILE
DIRECT SHEAR (Leutner) on the connection between bituminous
strata
CONCRETE:
FLEXURE ON BEAMS AND TILES
CEMENT:
FLEXURE on 40x40x160 mm specimens
COMPRESSION on cubes 40, 50, 70 mm
METAL, PLASTIC, WIRES, ROPES, TEXTILES, PAPERS ETC.
TENSILE TESTS, 50kN max capacity load
CLAY BLOCKS:
PUNCHING
ROCK AND STONES:
UNIAXIAL SPLITTING TENSILE

S206N

TECHNICAL FEATURES:
By using suitable devices, Unitronic tester, within the limits of its max. 200 kN capacity for compression/flexural and 50 kN for tensile, performs
compression, flexural, splitting tensile and direct tensile tests, with automatic load or displacement/deformation control.
The load is applied by a mechanical jack that is driven by a motor brushless with closed loop through optic encoder and controlled by a
microprocessor. Stroke electric end switches are applied to the load piston to save the machine from accidental handlings.
The two crossheads foresee couplings to fix the different test devices (see accessories). The stress is measured by an electric load cell; the
measurement and the displacement control of the crosshead is achieved by the electronic device incorporated into the machine.

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 509

SECTION S | SOIL

FIRMWARE SPECIFICATIONS OF THE FRAME

Electronic control unit “Cyber-plus Evolution” with Touch-Screen Max. load: 200 kN Compression; 50 kN tensile.
colour display, that runs like a standard PC based on Windows Max. vertical daylight: 900 mm (without accessories)
operating system for the management and analysis of the data,
Max. vertical daylight with compression platens: 800 mm
test results, graphs.
Compression platens diameter: 216 mm (upper platen on seat ball)
The Touch-Screen icon interface allows an easy set up of the
parameters and immediate execution of the test. Distance between columns: 650 mm
The machine can be connected to a PC for remote test execution Crosshead travel: ± 200 mm (400 mm total)
through suitable Software; the machine can in any case perform Testing speed range: from 0.01 to 100 mm/min
the tests without any external PC, because of the “Cyber-Plus” Load rate: from 1 N/s to 5 kN/s
grants performances like a PC.
Displacement resolution: 0.01 mm with accuracy better than 0.2%
Direct connection to Intranet (connection to a LAN network) and
Machine Class: 1
Internet to establish a remote communication and receive an
immediate diagnostic analysis from Matest technicians, or for The Unitronic 200 kN is supplied complete with:
updates of the software. Electric load cell 200 kN capacity, crosshead displacement device,
upper with seat ball and lower compression platens.
Unlimited memory storage with: 2 USB ports, 1 SD card slot.
Are not included: accessories and software for specific tests that
RJ45 network connection must be ordered separately (see accessories).
Possibility to select different languages. Note: The machine can be equipped with intermediate load
Hardware technical details: see p. 00 cells to the max. capacity of the machine, to satisfy
specific test requirements.
Power supply: 230V 1ph 50-60Hz 850W
Dimensions: 950x560x2400 mm
Weight: 820 kg approx.

UNITRONIC screen examples: CBR test CBR test result S206-21N Software for Duriez test

B043-01N Software Marshall test C109-11N Software for flexural File Marshall test
test on concrete beam

Tel: +44 (0) 1442 402770

 E: [email protected]

510 RETURN TO HOMEPAGE

SECTION S | SOIL

S206N UNITRONIC 200 KN CAN PERFORM THE FOLLOWING TESTS:

CBR TEST MARSHALL TEST CEMENT COMPRESSION CONCRETE FLEXURE

DURIEZ SPLITTING TENSILE BITUMEN CEMENT FLEXURE CLAY BLOCKS PUNCHING

UNCONFINED COMPRESSION DIRECT SHEAR (LEUTNER) SPLITTING TENSILE TILE FLEXURE

BLOCK PAVERS

UNIAXIAL ROCK SPLITTING AUTOMATIC SCB SYSTEM SPLITTING TENSILE TENSILE TEST ON METALS,
TENSILE CONCRETE CYLINDERS PLASTIC, WIRES, TEXTILES ETC.

Note: S206N UNITRONIC 200 kN can perform many other different test (like for ex.: quick triaxial, unconfined, etc.) by utilizing suitable
accessories and electric load cells.

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 511

SECTION S | SOIL

S206N UNITRONIC 200 KN, CAN PERFORM THE FOLLOWING TESTS:

CBR: CALIFORNIA BEARING RATIO TEST DIRECT SHEAR (LEUTNER) BETWEEN BITUMINOUS STRATA

STANDARDS: EN 13286 -47 | ASTM D1883 | BS 1377:4 STANDARD: ALP A StB t.4
S337-34
AASHTO T193 | NF P94-078 | CNR UNI 10009
Direct shear test (LEUTNER)
on the connection between
S212-05
bituminous strata, carried
out on asphalt cylinder
specimens Ø 150 mm or
100 mm obtained from road
cores or on laboratory made
specimens.
CBR Mould

S206N Unitronic 200 kN

S337-34 Strain gauge load cell 50 kN capacity B047-10 + B047-11
S337-51 Calibration process of load cell / Unitronic S206N Unitronic 200 kN
S206-31 Flange/connector of the load cell S337-34 S337-34 Strain gauge load cell 50 kN capacity
S212-01 Loading piston S337-51 Calibration process of load cell / Unitronic
S218N Software for CBR test (p. 00) S206-31 Flange/connector of the load cell S337-34
S212-05 Loading piston
B047-10 LEUTNER testing head for specimens Ø 150 mm
DURIEZ TEST ON 80 AND 120 MM DIAMETER SAMPLES B047-11 Spacers for Ø 100 mm specimens with Leutner head
B043-03N Software for Leutner and Marshall tests (p. 000).
STANDARD: NF P98-251/1, NF P98-251/4

SPLITTING TENSILE TEST

STANDARDS: EN 12697-23, 12 | ASTM D6931 | AASHTO T283

CNR 134

B095-01

S206N Unitronic 200 kN

B096-01 Duriez set Ø 80 mm (p. 000)
B095-01 Duriez set Ø 120 mm (p. 000)
S206-21N Software for Duriez test (p. 000)
B047-02 + B047-04
S206N Unitronic 200 kN
S337-34 Strain gauge load cell 50 kN capacity
MARSHALL STABILITY TEST
S337-51 Calibration process of load cell / Unitronic
S206-31 Flange/connector of the load cell S337-34
STANDARDS: EN 12697-34 | ASTM D1559, D5581, D6926
S212-05 Loading piston
AASHTO T245 | BS 598:107 | NF P98-251-2
B047-02 Splitting tensile device for samples Ø 4” and 6” (p. 000)
B047-04 Set of TWO displacement transducers
with accessories (p. 000)
B043-02N Software for Splitting Tensile test (p. 00)

B046N

S206N Unitronic 200 kN

S337-34 Strain gauge load cell 50 kN capacity
S337-51 Calibration process of load cell / Unitronic
S206-31 Flange/connector of the load cell S337-34
S212-05 Loading piston
B046N Stability mould
B043-01N Software for Marshall test (p. 000) B043-01N Software Marshall test

Tel: +44 (0) 1442 402770

 E: [email protected]

512 RETURN TO HOMEPAGE

SECTION S | SOIL

FLEXURAL TEST ON CONCRETE BEAMS FLEXURAL TEST WITH CENTRE POINT ON CONCRETE BEAMS
AND CLAY TILES
STANDARDS: EN 12390-5 | ASTM C78, C293 | AASHTO T97
NF P18-407 | BS 1881:118 | UNE 83305 STANDARDS: EN 12390-5 | ASTM C78, C293 | BS 1881:118
S206N Unitronic 200 kN
S205-18 Flexure device with centre point loading to test clay tiles
and concrete beams dimensions 100x100x400(500) mm
Consisting of lower beam with two bearers
(one articulated) adjustable from 100 to 315 mm, and
upper central articulated bearer fixed to the load cell.
S206N Unitronic 200 kN C106 Weight: 20kg approx.
C106 Flexure device (p. 000) S337-34 Strain gauge load cell 50 kN capacity
C109-11N Software for flexural tests on concrete beams. (p. 00) (to replace the 200 kN load cell)
S206-31 Flange/connector of the load cell S337-34
C109-11N Software for flexural tests on concrete beams (p. 00)
TWO POINT FLEXURAL AND TRANSVERSE TESTS ON CONCRETE
BEAMS AND BENDING TEST METHOD ON GLASS-FIBRE
REINFORCED CONCRETE

STANDARDS: EN 1170-4, EN 12390-5 | ASTM C78, C293

S206N Unitronic 200 kN
S337-34 Strain gauge load cell 50kN capacity
S337-51 Calibration process of load cell / Unitronic
S205-16 Four-point bending device to test glass-fibre reinforced
concrete.
Rollers dimensions: Ø 40 by 310 mm long
Lower rollers adjustable from 110 to 310 mm
Upper rollers adjustable from 45 to 120 mm
Weight: 20 kg approx. S205-18
S206-31 Flange/Connector of the load cell S337-34
C109-11N Software for flexure tests on concrete beams (p.00) SPLITTING TENSILE TEST ON CONCRETE CYLINDERS

STANDARDS: EN 12390-6 | ASTM C496 | NF P18-408 | BS 1881:117

C100-01 + C101-01
S206N Unitronic 200 kN
C101-01 Splitting tensile test device (technical details and other
devices: p. 000)
C100-01 Packing strips for the device C101-01
S205-16 C109-12N Software for splitting tensile test. (p. 00)

SPLITTING TENSILE TEST ON CONCRETE CUBES AND BLOCK

PAVERS

STANDARDS: EN 1338 | EN 12390-6

C100-02 + C103
S206N Unitronic 200 kN
C103 Splitting tensile test device (p. 000)
C109-11N Software for flexural test on concrete beam C100-02 Packing strips for the device C103
C109-12N Software for Splitting tensile test (p. 00)

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 513

SECTION S | SOIL

PUNCHING TEST ON CLAY BLOCKS TENSILE TESTS ON METALS, PLASTICS, WIRES, TEXTILES ETC.

STANDARDS: EN 15037-2, 15037-3 | UNI 9730-3 STANDARDS: ASTM D2166 | BS 1377:7 | AASHTO T208
S337-32

C093-11

H005-11

H014-06

S205-11
S206N Unitronic 200 kN
C093-11 Punching device for clay block for flooring tests
S205-15 Holding beam for the device
S337-32 Strain gauge load cell 10 kN capacity
S206-32 Flange/Connector for the load cell S337-32
S337-51 Calibration process of load cell / Unitronic
C109-16N Software for the punching test (p. 00) S206N Unitronic 200 kN
H005-11 Tensile heads, upper and lower (p. 000).
Daylight between heads: min. 50 mm / max. 420 mm
COMPRESSION TEST ON MORTAR SPECIMENS S206-33 Flange/connector of the tensile heads H005-11
H005-21 Flat seizing grip for flat specimens 1-10 mm thickness
STANDARDS: EN 196-1 | ASTM C109, C349 | NF P15-451 by 25 mm max. width, and round specimens Ø 3-5 mm
EN ISO 679 | DIN 1164 H005-31 “V” shape seizing grips for round specimens Ø 5-12 mm

E170
S206N Unitronic 200 kN
E170 Compression device on portions of 40x40x160 mm
specimens
(devices for different specimens described at p. 000)
E163N Software for the compression test (p. 00)

FLEXURAL TEST ON MORTAR PRISMS 40X40X160 MM

H009N Practical example of a saving test graph where the user
can select which traces have to be shown, modify the scales or
STANDARDS: EN 196-1 | ASTM C348 | NF P15-451
personalize the colors and give a new name to the axis upgrading.
DIN 1164 | EN ISO 679

OPTIONAL ACCESSORIES

H014 Extensometer, electronic, for tensile deformation

strength tests (p. 000)
H009N Software for load/deformation, graphs, test certificate
E172-01 Technical specifications: see p. 000 where there are also listed
S206N Unitronic 200 kN
devices to test plastics, wires, ropes, flexural and bending tests and
E172-01 Flexure device for 40x40x160 mm specimens
various models of extensometers.
(available also device to ASTM, see p. 000)
S337-32 Strain gauge load cell 10 kN capacity
S206-32 Flange/connector of the load cell S337-32 Note: Accessories for specific tests listed above, are common
S337-51 Calibration process of load cell / Unitronic for different tests. We recommend to check them when
S164N Software for the flexural test (p. 00) ordering, to avoid duplications.

Tel: +44 (0) 1442 402770

 E: [email protected]

514 RETURN TO HOMEPAGE

SECTION S | SOIL

PLATE BEARING TEST

STANDARDS: ASTM D1194, D1195, D1196 | BS 1377:9 | CNR N° 92 and 146 | UNE 7391 | Comparable to DIN 18134
This test is performed for the determination of the bearing capacity of a soil in-situ on road constructions, foundations, road subgrades, airport
and highway pavements.
A wide range of plate bearing test equipment is available, together with many accessories according to the different Standards and specific
end-user needs.
The hand pumps 100 kN and 200 kN capacity are “Enerpac Made” and all models have double speed, ensuring fast approach.

AVAILABLE MODELS

S222 KIT S222D KIT

PLATE BEARING TEST EQUIPMENT 100 KN PLATE BEARING TEST EQUIPMENT 100KN
CAPACITY - 1 DIAL GAUGE MODEL CAPACITY - 1 DIGITAL GAUGE MODEL
ANALOGUE MEASURING SYSTEM WITH DIAL MANOMETER DIGITAL MEASURING SYSTEM WITH DIGITAL MANOMETER
STANDARD: CNR N° 146, method “A” Same composition of S222KIT except:
Consisting of: S222-02D Digital pressure manometer 0 - 100 kN
S222-01 Hydraulic jack 100 kN capacity, complete with hand with 10N resolution, instead of the analogue gauge
pump, rubber pipe with fast connector, set of extension S222-02.
rods of different lengths, carrying case.
S222-02 Analogue pressure gauge 0-100 kN, div. 0.5 kN S222-02D | S225-02D
S226-05 Load plate Ø 300 mm DIGITAL PRESSURE MANOMETER
S226-12 Device for centre dial gauge measure, with spherical
seat. The applied load is measured by a high precision electric load cell
S222-03 Datum bar assembly, 2.5 m long, telescopic, alumin- with digital display, granting accurate readings also at low loads.
ium made, adjustable in height, complete with base - 65.000 divisions
supports, plumb and spirit level. Packed separayely. - 10N resolution
S377 Dial gauge 25x0.01 mm - linearity: 0.05%
S226-16 Articulated dial gauge support with adjustment device. - hysteresis: 0.03%
- repeatability: 0.02%
Weight: 60 kg approx. - display: LCD with high visibility
- display height: 16 mm
- battery operated, 12 months life

S222-02D | S225-02D

S222-02D
S223-01 | S223-02 S225-02D

S222 KIT

ACCESSORY for S222 KIT and S223 KIT

S223-01 PRESSURE GAUGE, range 0 - 50 kN, div. 0.25 kN with

large dial Ø 200 mm, complete with fast connector,
used for accurate readings at low loads, as for ex.
pre-load of 0.5 kg/cmq.

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 515

SECTION S | SOIL

S223 KIT
PLATE BEARING TEST EQUIPMENT 100 KN CAPACITY - 3 DIAL GAUGES MODEL
ANALOGUE MEASURING SYSTEM WITH DIAL MANOMETER
STANDARDS: CNR N° 146, method “B” | BS 1377:9
Consisting of:
S222-01 Hydraulic jack 100 kN capacity, complete with hand pump, rubber pipe with fast connector, set of extension rods of different lengths,
carrying case.
S222-02 Analogue pressure gauge 0-100 kN, div. 0.5 kN.
S226-13 Upper spherical seat.
S226-05 Load plate Ø 300 mm
S226-06 Intermediate plate Ø 160 mm
S222-03 Datum bar assembly, 2.5 m long, telescopic, aluminium made, adjustable in height, complete with base supports, plumb and spirit
level. Packed separayely.
(Alternative solutions: S223-03 “Y” measuring system, Swiss method. See p. 000).
S377 n° 3 dial gauges 25x0.01 mm
S226-16 n° 3 articulated dial gauge supports with adjustment device.
Weight: 60 kg approx.

S223 KIT

S223D KIT
PLATE BEARING TEST EQUIPMENT 100 KN CAPACITY - 3 DIAL GAUGES MODEL
DIGITAL MEASURING SYSTEM WITH DIGITAL MANOMETER
Same composition of S223KIT except:
S222-02D Digital pressure manometer 0 - 100 kN with 10N resolution, instead of the analogue gauge S222-02.

S223D KIT

Tel: +44 (0) 1442 402770

 E: [email protected]

516 RETURN TO HOMEPAGE

SECTION S | SOIL

S225 KIT
PLATE BEARING TEST EQUIPMENT 200 KN CAPACITY - 3 DIAL GAUGES MODEL
ANALOGUE MEASURING SYSTEM WITH DIAL MANOMETER
STANDARDS: CNR N° 146, method “B” | BS 1377:9, and using loading plates (accessory) dia. 450, 600, 760 mm, it meets also:
ASTM D1195, D1196 | CNR N. 92
Consisting of:
S225-01 Hydraulic jack 200 kN capacity, complete with hand pump, rubber pipe with fast connector, set of extension rods of different lengths,
carrying case.
S225-02 Analogue pressure gauge 0-200 kN, div. 1 kN.
S226-13 Upper spherical seat.
S226-05 Load plate Ø 300 mm
S226-06 Intermediate plate Ø 160 mm
S222-03 Datum bar assembly, 2.5 m long, telescopic, aluminium made, adjustable in height, complete with base supports, plumb and spirit
level. Packed separayely. (Alternative solutions: S223-03 “Y” measuring system, Swiss method. See p. 000).
S377 n° 3 dial gauges 25x0.01 mm
S226-16 n° 3 articulated dial gauge supports with adjustment device.
Weight: 70 kg approx.

S225 KIT

S222-02D | S225-02D

S225D KIT B103-10

PLATE BEARING TEST EQUIPMENT 200 KN BEARING PLATE 600 MM Ø CAST ALUMINIUM
CAPACITY - 3 DIAL GAUGES MODEL STANDARD: NF P94-117-1
DIGITAL MEASURING SYSTEM WITH DIGITAL MANOMETER Used to determine the static deformation of flexible road pavement
Same composition of S225KIT except: and with the plate bearing equipment.
S225-02D Digital pressure manometer 0 - 200 kN with 10N Technical details: see p. 000
resolution, instead of the analogue gauge S225-02.

ACCESSORY for S225 KIT

S223-02 PRESSURE GAUGE, range 0 - 50 kN, div. 0.25 kN with

large dial Ø 200 mm, complete with fast connector,
used for accurate readings at low loads, as for ex.
pre-load of 0.5 kg/cmq. B103-10

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 517

SECTION S | SOIL

S226 KIT
PLATE BEARING TEST EQUIPMENT 500 KN CAPACITY - 3 DIAL GAUGES MODEL
ANALOGUE MEASURING SYSTEM WITH DIAL MANOMETER
STANDARDS: CNR N° 146, method “B” | BS 1377:9, and using loading plates (accessory) Ø 450, 600, 760 mm, it meets also:
ASTM D1195, D1196 | CNR N. 92
Consisting of:
S227-02 Hydraulic jack 500 kN capacity, complete with hand pump, spherical seat, rubber pipe with fast connector, set of extension rods of
different lengths, carrying case.
S227-03 Analogue pressure gauge 0-500 kN, div. 2 kN.
S226-05 Load plate Ø 300 mm
S226-06 Intermediate plate Ø 160 mm
S222-03 Datum bar assembly, 2.5 m long, telescopic, aluminium made, adjustable in height, complete with base supports, plumb and spirit
level. Packed separayely. (Alternative solutions: S223-03 “Y” measuring system, Swiss method. See p. 000).
S377 n° 3 dial gauges 25x0.01 mm
S226-16 n° 3 articulated dial gauge supports with adjustment device.
Weight: 110 kg approx.

S226 KIT

S226D KIT
PLATE BEARING TEST EQUIPMENT 500 KN CAPACITY - 3 DIAL GAUGES MODEL
DIGITAL MEASURING SYSTEM WITH DIGITAL MANOMETER
STANDARDS: CNR N° 146, method “B” | BS 1377:9, and using loading plates (accessory) Ø 450, 600, 760 mm, it meets also:
ASTM D1195, D1196 | CNR N. 92
Same composition of S226 KIT except for:
S227-03D Digital pressure manometer 0 - 500 kN with 20N resolution, instead of the analogue gauge S227-03.

S226D KIT

Tel: +44 (0) 1442 402770

 E: [email protected]

518 RETURN TO HOMEPAGE

SECTION S | SOIL

S224 KIT
DIGITAL PLATE BEARING TEST EQUIPMENT 100 KN CAPACITY
3 LINEAR DISPLACEMENT TRANSDUCERS AND CYBER-PLUS DATA ACQUISITION SYSTEM
STANDARDS: CNR N° 146, method “B” | BS 1377:9
Consisting of:
S222-01 Hydraulic jack 100 kN capacity, complete with hand pump, rubber pipe with fast connector, set of extension rods of different
lengths, carrying case.
S226-13 Upper spherical seat.
C116-09S Pressure transducer, connected to the pump.
C405-15N Cyber-Plus Evolution “Touch Screen” for data acquisition, visualization, processing and storing, directly connected to PC or printer.
Technical details: see p. 000
S224-21N Software for test data processing.
S226-05 Load plate Ø 300 mm
S226-06 Intermediate plate Ø 160 mm
S222-03 Datum bar assembly, 2.5 m long, telescopic, aluminium made, adjustable in height, complete with base supports, plumb and spirit
level. Packed separayely. (Alternative solutions: S223-03 “Y” measuring system, Swiss method. See p. 000).
S336-14 n° 3 linear displacement transducers, 50 mm travel.
S336-31 n° 3 Extension cables for transducer, 5 m long.
S226-16 n° 3 articulated transducer supports with adjustment device.
S335-15 n° 3 universal coupling pliers for transducers.
Weight: 60 kg approx.

S224-01 KIT
DIGITAL PLATE BEARING TEST EQUIPMENT 200 KN CAPACITY
3 LINEAR DISPLACEMENT TRANSDUCERS AND CYBER-PLUS DATA ACQUISITION SYSTEM
STANDARDS: CNR N° 146, method “B” | BS 1377:9, and using loading plates (accessory) Ø 450, 600, 760 mm, it meets also:
ASTM D1195, D1196 | CNR N. 92
Consisting of:
S225-01 Hydraulic jack 200 kN capacity, complete with hand pump, rubber pipe with fast connector, set of extension rods of different
lengths, carrying case.
S226-13 Upper spherical seat.
C116-09S Pressure transducer, connected to the pump.
C405-15N Cyber-Plus Evolution “Touch Screen” for data acquisition, visualization, processing and storing, directly connected to PC or printer.
Technical details: see p. 000
S224-21N Software for test data processing.
S226-05 Load plate Ø 300 mm
S226-06 Intermediate plate Ø 160 mm
S222-03 Datum bar assembly, 2.5 m long, telescopic, aluminium made, adjustable in height, complete with base supports, plumb and spirit
level. Packed separayely. (Alternative solutions: S223-03 “Y” measuring system, Swiss method. See p. 000).
S336-14 n° 3 linear displacement transducers, 50 mm travel.
S336-31 n° 3 Extension cables for transducer, 5 m long.
S226-16 n° 3 articulated transducer supports with adjustment device.
S335-15 n° 3 universal coupling pliers for transducers.
Weight: 70 kg approx.

S224-01 KIT
(similar to S224 KIT and S224-02 KIT)

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 519

SECTION S | SOIL

S224-02 KIT
DIGITAL PLATE BEARING TEST EQUIPMENT 500 KN CAPACITY
3 LINEAR DISPLACEMENT TRANSDUCERS AND CYBER-PLUS DATA ACQUISITION SYSTEM
STANDARDS: CNR N° 146, method “B” | BS 1377:9, and using loading plates (accessory) Ø 450, 600, 760 mm, it meets also:
ASTM D1195, D1196 | CNR N. 92
Consisting of:
S227-02 Hydraulic jack 500 kN capacity, complete with hand pump, spherical seat, rubber pipe with fast connector, set of extension rods of
different lengths, carrying case.
C116-09S Pressure transducer, connected to the pump.
C405-15N Cyber-Plus 8 Evolution “Touch Screen” for data acquisition, visualization, processing and storing, directly connected to PC or printer.
Technical details: see p. 000
S224-21N Software for test data processing
S226-05 Load plate Ø 300 mm
S226-06 Intermediate plate Ø 160 mm
S222-03 Datum bar assembly, 2.5 m long, telescopic, aluminium made, adjustable in height, complete with base supports, plumb and spirit
level. Packed separayely. (Alternative solution: S223-03 “Y” measuring system, Swiss method).
S336-14 n° 3 linear displacement transducers, 50 mm travel.
S336-31 n° 3 Extension cables for transducer, 5 m long.
S226-16 n° 3 articulated transducer supports with adjustment device.
S335-15 n° 3 universal coupling pliers for transducers.
Weight: 110 kg approx.

ACCESSORIES

S226-01 LOADING PLATE Ø 450 mm

S226-02 LOADING PLATE Ø 600 mm S226-01 + S226-02 + S226-03
S226-03 LOADING PLATE Ø 760 mm
S226-09 SET OF TELESCOPIC EXTENSION RODS, aluminium
made, to be connected to the datum bar mod. S222-03
(2.5 m long) to obtain a max. adjustable lenght of 5.5 m
as requsted by ASTM, CNR Specifications

S223-03
S226-09 + S222-03
“Y” MEASURING SYSTEM - SWISS METHOD
STANDARD: SNV 70312
Aluminium alloy made, lightweight and very easy to use, it may be
used as alternative solution to the datum bar assembly mod. S222-03.
This system is applicable to the plate bearing equipment with 3 dial
gauge or 3 displacement transducers.
Weight: kg 7 approx.
BENKELMAN BEAM APPARATUS
STANDARDS: NF P94-117-1 | NF P98-200/2 | AASHTO:T256
Utilized in conjunction with the plate bearing test equipment, to
determine the static deformation of road pavements EV1 - EV2 and
Westergard. See section “B” Bitumen, mod. B100 p. 000

S223-03 + S226-16

S226-50
OFFICIAL ACCREDIA CALIBRATION CERTIFICATE B100 B102
(equivalent UKAS, ENAC, DAKKS, SAS, COFRAC etc.) of the applied
load for the Bearing Test Equipment from mod. S222KIT to mod.
S226KIT (p. 000 to 000) and for Field CBR/Unconfined test equip-
ment mod. S131KIT, S210KIT, S220KIT (see p. 000).
The calibration is carried out only at Matest factory.

Tel: +44 (0) 1442 402770

 E: [email protected]

520 RETURN TO HOMEPAGE

SECTION S | SOIL

C405-15N
CYBER-PLUS TOUCH SCREEN
DATA ACQUISITION AND PROCESSING SYSTEM
8 Channels acquisition and processing data system, 24 bit resolution.
Electronic advanced technology, colour touch screen 1/4 VGA,
high graphic performances, the unit automatically performs test
and data processing. A certificate can be printed through a printer
(optional) directly connected to the unit through the USB port
The Cyber-Plus is equipped with slots for external pendrive or SD
card infinite memory supports, it can be directly connected to a PC.
Contained in a practical and sturdy watertight carrying case, can be
powered from an electrical network 90-270 V or use the internal
battery and charger granting one full day on-site use.
Hardware technical details: see p. 00

S337-51
Calibration process between one displacement transducer and the
data acquisition system C405-15N

AS AN ALTERNATIVE:

C405-15N

S336-47 AVAILABLE MODELS

S336-41 S336-43 S336-45
S336-43 Gauge block, nominal length 10 mm
GAUGE BLOCKS. Grade 1 S336-45 Gauge block, nominal length 25 mm
Used to calibrate the linear displacement transducers. S336-47 Gauge block, nominal length 50 mm

Graph of end test Test results

Test execution Test results graph

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 521

SECTION S | SOIL

S228N
DYNAMIC PLATE LOAD TEST
LIGHT WEIGHT DEFLECTOMETER
STANDARDS: ASTM E 2835-11 | TP BF-StB part B 8.3 | ZTV E-StB 2017 | RIL 836 | RVS 08.03.04 (Austria)
Used in earthwork and road construction to determine the soil bearing capacity and the compaction quality of soils and non cohesive subbases,
as well as for soil improvement applications. The test method is suited for coarse-grain and mixed-grain soil having maximum grain size of 63
mm. The test method may be used to determine the dynamic modulus of deformation of soil in the range Evd = 15...70 MN/m².

ADVANTAGES over the static plate load tester:

- Immediate evaluation of each measurement
- Only 2 minutes per measurement point
- Time and cost-saving
- No need for construction plant as kentledge
- Easy to handle by one person
- Ability to test in inaccessible locations
Being easy to handle and providing immediate measuring results,
the Light Weight Deflectometer is additionally suited for monitoring
intra-company operations. It facilitates quick decisions for continu-
ing construction work at the site.
SPECIFICATIONS:
- Measuring instrument - small, portable and precise
- Intuitive menu navigation with 10 selectable languages
- Variable text input and pre-loading pulses
- Three settlement values shown during test
- Settlement mean value and Evd modulus automatically calculated
- Drop weight: 10 kg (extendable to 15 kg)
- Measure range: Evd 15-70 MN/m² (extendable to 105 MN/m²)
S228-13
- Measure depth: 600 mm
- Load plate Ø 300 mm
- SD card for storage of 10.000 data tests
- Up to 1.500 tests with just one set of batteries (4xR6)
- High quality zinc plated galvanization of metallic parts, against
corrosion
The tester is supplied complete with loading unit, load plate, meas-
uring instrument with SD card and instructions (in weatherproof full
leather carrying case)
Total Weight: 30 kg approx.

S228-14

ACCESSORIES S228N

S228-05 DROP WEIGHT of 15 kg.

Measuring range of 70-105 MN/m².
S228-10 PROTOCOL SOFTWARE. Add information about the
measuring point and use the confortable user interface
for issuing and easy-view archiving of representative
A4-protocols.
S228-11 THERMAL PRINTER in case (with power battery, power
supply and connection cable)
S228-12 INTEGRATED GPS SYSTEM. To proof the exact
coordinates of the measuring point.
S228-13 TRANSPORT CART. For long distances at the site.
S228-14 MAGNETIC STAND. For proper positioning of loading unit.
S228-15 TRANSPORT BOX. For safe transport and storage.
S228-06 WI-FI SD CARD. Fast data transfer to mobile, phone,
tablet or PC. Free mobile apps for both Android and iOS. S228-15

Tel: +44 (0) 1442 402770

 E: [email protected]

522 RETURN TO HOMEPAGE

SECTION S | SOIL

RELATIVE DENSITY OF COHESIONLESS SOIL

VIBRATING TABLE METHOD
The relative density set is proposed in two versions according to EN or ASTM Specifications:

S238N KIT S238-01N KIT

RELATIVE DENSITY OF COHESIONLESS SOILS RELATIVE DENSITY OF COHESIONLESS SOILS
STANDARD: EN 13286-5 STANDARDS: ASTM D4253, D4254
This test covers the determination of the maximum dry density and The method is applicable for the determination of the relative den-
the water content (humidity/density ratio) of cohesionless mixtures sity of cohesionless soil where impact compaction will not produce
where the max density by the impact method is lower than the a well defined moisture/density relationship curve.
vibratory method. The maximum density of the impact test is normally less than the
The method is applicable to materials containing up to 12% fines vibratory method.
(< 0.063 mm) by mass and max. particle size is 80 mm. The set is composed of:
The test is performed to road construction mixtures.
S238-10 Vibrating electromagnetic table, as above described.
The set is composed of: Power supply: 230V 1ph 50-60Hz
S238-10 Vibrating electromagnetic table, dimensions 762x762 mm, S238-11N Relative density mould 0,5 cu. ft. capacity with
vibration frequency 3600 rpm, amplitude range: 0.05 to accessories.
0.64 mm, max. load capacity 250 kg, complete with sep- S238-13N Relative density mould 0,1 cu. ft. capacity with
arate control panel. accessories.
Power supply: 230V 1ph 50-60Hz S238-14N Surcharge weight and base with handle to ASTM for
the 0.5 cu. ft. mould.
S238-11EN Relative density mould 14 liters capacity with S238-15N Surcharge weight and base with handle to ASTM for
accessories. the 0.1 cu. ft. mould.
S238-12 Surcharge weight and base with handle to EN S238-16 Relative density gauge measuring set.
for the 14 liters mould.
Total weight: 310 kg approx.
Total weight: 290 kg approx.

S238N KIT

S238-01N KIT

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 523

SECTION S | SOIL

S230 KIT
ASTM | AASHTO BALLOON DENSITY APPARATUS
1600 ML CAPACITY
STANDARDS: ASTM D2167 | AASHTO T205 | CNR N° 22
Used to determine the in-sity density of fine graded compacted or
bonded soil. The apparatus is placed over the hole excavated in the
soil, and water is pumped into a rubber balloon and forced into the
hole. The amount of water displaced into the ballon is measured
from the graduation of the scale.
The instrument consists of a graduated
plexiglass cylinder 1600 ml capacity
housed within an aluminium alloy casting,
a rubber pump with stop valve, a density
plate and 12 rubber balloons.
Dimensions: 340x340x700 mm
Weight: 6 kg approx.

S232 KIT S233 KIT

SPARE

S230-01 Rubber balloons, pack of 12

S233 KIT
NF BALLOON DENSITY APPARATUS
6000 ML CAPACITY
Identical to mod. S232 KIT, but with capacity of 6 litres.
Weight: 15 kg approx.

SPARE

S233-01 Reinforced rubber membrane, pack of 6

ACCESSORIES

S230 KIT Used for levelling, digging, collecting and maintaining the soil
samples:
S232 KIT S240-01 SCRAPER to level the V198 CHISEL 300 mm long
NF BALLOON DENSITY APPARATUS ground x 25 mm wide
S240-02 METAL DIBBER TOOL V186 DENSITY SPOON, big
3000 ML CAPACITY
STANDARD: NF P94-061-2 S240-05 METAL POINTED ROD sized
V195 RUBBER MALLET V188 TROWEL, 100x200 mm
Used to determine the in-situ density of fine graded compacted or
Ø 50 mm V183 ALUMINIUM SCOOP
bonded soil, this unit has the same test system of mod. S230 KIT,
but with a capacity of 3000 ml as requested by French Specification. V193 STEEL HAMMER 300 g 325 cc
A hand-driven piston forces the water into the rubber membrane. A V194 STEEL HAMMER 2 kg V125-03 TINNED CAN
dial gauge measures the water pressure so to execute all the test at V199 DENSITY PICK 5 litre cap.
the same pressure.
An index engraved on the stem of the piston measures the volume
of water filling the hole.
The unit is supplied complete with 6 reinforced rubber membranes,
4 locking clamps, base plate, accessories.
Dimensions: 360x360x700 mm
Weight: 10 kg approx.

SPARE
S240-01...V199
S232-01 Reinforced rubber membrane, pack of 6

Tel: +44 (0) 1442 402770

 E: [email protected]

524 RETURN TO HOMEPAGE

SECTION S | SOIL

FIELD DENSITY SAND REPLACEMENT METHOD

STANDARDS: ASTM D1556 | AASHTO T191 | NF P94-061-3 | CNR N° 22 | UNE 7371

Used to determine the in-situ density of fine graned compacted soil The kit consists of:
and to verify the degree of compaction. Metal double cone assembly with valve, galvanized for rust
The test consists in digging a hole into the ground and then collect, protection.
dry and weight the sampled soil.
The hole is now filled with dry sand from the cone container and the Metal base with rimmed centre hole for cone housing, galvanized.
volume of sand recorded. Two plastic jar, 5 litre capacity. (One jar only 15 litre capacity
Three versions are available Ø 4” 6.5” 12” each one suitable for complete of cone fixing device for S231 KIT version)
different grain sized.
The S231KIT model Ø 12” is recommended for coarse grained soil
and gravel (over 38 mm diameter). The calibrating container is an accessory, to be ordered separately.

S231-01

NEW

S234-13

S234-01

S234-10 KIT S234 KIT S231 KIT

Model Diameter Double cone Metal base Jar plastic Dimensions Weight Calibrating container
inch / mm with valve with hole mm kg (optional accessory)
S234-10 KIT 4” (101.6 mm) S234-11 S234-12 V121 (2) 190x190x500 2.300 S234-13
S234 KIT 6.5” (165.1 mm) S234-05 S234-06 V121 (2) 305x305x600 3.350 S234-01
S231 KIT 12” (304.8 mm) S231-05 S231-06 S231-11 (1) 620x620x920 13.600 S231-01

Note: all parts can be purchased individually.

ACCESSORIES

S235 STANDARD SAND for density tests, passing 600 micron

and retained on 300 micron. ASTM, AASHTO, BS.
Bag of 50 kg.
S235-01 STANDARD SAND, passing 0.4 mm and retained on
2 mm. CNR N° 22. Bag of 50 kg S235

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 525

SECTION S | SOIL

BS SAND REPLACEMENT APPARATUS

STANDARDS: BS 1377:9, BS 1924:2
Used to determine the in-situ density of fine graned compacted soil.
The apparatus consists of: sand pouring cylinder with shutter made of cast aluminium and accurately machined, upper cylinder, metal tray with
fixed centre hole for cone housing.
The cylinder is available with 100, 150 and 200 mm diameter (Ø 200 mm is recommended for coarse grained soil and gravel).

S236 KIT...S237 KIT

Available Ø Pouring cylinder, shutter Metal tray with Optional accessory: Weight of the
Models mm and upper cylinder centre hole Calibrating container complete KIT
S236 KIT 100 Consisting of: S236-05 S236-06 S236-07 kg 10.800
S236-01 KIT 150 Consisting of: S236-10 S236-11 S236-12 kg 14.150
S237 KIT 200 Consisting of: S237-05 S237-06 S237-07 kg. 22.600

S244
PINHOLE TEST EQUIPMENT
DISPERSIBILITY DETERMINATION
STANDARDS: ASTM D4647 | BS 1377:5
Utilized to evaluate the erosion on soil samples having high degree
of sodium content, the Pinhole apparatus reproduces the water
flowing in a cavity obtained from a soil specimen.
The apparatus consists of a cylindrical container equipped at its
ends of water inlet/outlet connectors, tube with graduated scale,
base support with rod.
Weight: 4 kg approx.

ACCESSORIES

S245-04 CONSTANT LEVEL TANK. Details and picture:

see p. 000
S244
V230-02 TUBING, inside Ø 8 mm, 5 m long

Tel: +44 (0) 1442 402770

 E: [email protected]

526 RETURN TO HOMEPAGE

SECTION S | SOIL

CONSTANT HEAD PERMEAMETERS FALLING HEAD PERMEAMETER

STANDARDS: BS 1377:5 | ASTM D2434 | AASHTO T215 STANDARD: CEN ISO/TS 17892-11
Used to determine the permeability of granular, gravel and sand Used to determine the permeability of fine-grained soils such as
soils. The specimen is formed in an acrylic permeability cell, and clay-like or silty soils. The specimen is confined within the per-
water is passed through it from a constant level tank. meameter which is connected to the manometer tube filled with
The permeability cell has pressure points at different levels which water. The sample must be completely satured with water before
are connected to the manometer tubes fixed on a stand with gradu- the test, and the operator will check the rate of fall of the water in
ated scale. Two constant head permeability cells are available: the tube passing through the test specimen.
75 mm and 114 mm diameter. The set consists of:
S246-01
Permeameter stand with three manometer tubes each Ø 3, 4 and 6
mm for the different degrees of permeability, soaking reservoir with
S245-03 cock, tubing and connectors.
Dimensions: 1700x220x50 mm
Weight: 10 kg approx.

S252
COMPACTION PERMEAMETER
Ø 4” complete
(technical details: see next page)

S245-02 ALTERNATIVE:
S253
S245-04 COMPACTION PERMEAMETER
Ø 6” complete.

S245-01

S246-01
S245-01
CONSTANT HEAD PERMEABILITY CELL Ø 75 MM
with three pressure take-off points.
Formed by an acrylic plexiglass body held between two aluminium
anodized end plates. S252
Weight: 3 kg approx.

S245-02 ACCESSORIES for Compaction Permeameters Ø 4”

CONSTANT HEAD PERMEABILITY CELL Ø 114 MM
S252-01 PLEIN BASE and COLLAR Ø 4” for compaction tests.
with six pressure take-off points and an additional six blanked-off
S252-02 MOULD BODY Ø 4” with two lateral water inlet/outlet.
pressure points. Formed by an acrylic plexiglass body held between
two aluminium anodized end plates. When using this cell, two
manometer tube stands mod. S245-03 are required.
ACCESSORIES for Compaction Permeameters Ø 6”
Weight: 7 kg approx.
S253-01 PLEIN BASE and COLLAR Ø 6” for compaction tests.
S245-03 S253-02 MOULD BODY Ø 6” with two lateral water inlet/outlet.
MANOMETER TUBES AND STAND, comprising three tubes of con-
stant bore, graduated scale, tubing and connectors.
Dimensions: 210x50x1160 mm ACCESSORIES
Weight: 5 kg approx.
S355 DE-AIRING TANK 20 litre capacity made from acrylic
S245-04 plexiglass (see p. 000)
CONSTANT LEVEL TANK, made from acrylic plexiglass, wall mount- S355-01 WATER TRAP to collect the water condensation.
ing. The inlet, outlet and overflow pipes can be adjusted for height V203 PORTABLE VACUUM PUMP, 230V 1ph 50Hz
within the tank. V230-03 RUBBER TUBING for vacuum, 3 m long.
Weight: 3 kg approx. S325 NYLON TUBING, 20 m

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 527

SECTION S | SOIL

S248
PERMEAMETER STAND 4 CELL CAPACITY
FOR CONSTANT AND FALLING HEAD TESTS
This 4 cells capacity stand is designed to perform both constant
head and falling head permeability tests on compacted granular soil
samples.
The stand consists of a metal frame with water tank adjustable in
height between 1350 and 3450 mm for constant head tests. Sup-
plied complete with tubes, graduated rules, piping, connectors and
cocks; but without permeameters to be ordered separately.
The stand can hold up to 4 permeameters having Ø 4” or 6” to
perform different types of tests at the same time.
Dimensions: 1050x900x2000/3850 mm
Weight: 75 kg approx.

COMPACTION PERMEAMETERS
STANDARD: CEN ISO/TS 17892-11
Used for determining permeability to water of soil gravel, clay, sand
samples. Supplied complete with clamped upper and lower plate
giving the possibility to perform permeability tests also on com-
pacted samples, water inlet with valve, water outlet, two perforated
upper and lower plates, two stainless steel screens.
Stell made, galvanized against corrosion.

S253

S248 + Permeameters

S253 disassembled
S253-02
MODELS

S252
COMPACTION PERMEAMETER Ø 4” complete. Weight: 8 kg approx.

ACCESSORIES for S252

S252-01 PLEIN BASE and COLLAR for compaction test before the S253-01
permeability test
S252-02 MOULD BODY with two lateral water inlet/outlet for test S252-02
with piezometric measurement S252-01

S253 COMPACTION PERMEAMETER Ø 6” complete. ACCESSORIES

Weight: 16 kg approx.
CUTTING COLLAR, coupled to the
ACCESSORIES for S253 Permeameter body, it gets easier
the soil sampling.
S253-01 PLEIN BASE and COLLAR for compaction test before the
MODELS
permeability test
S253-02 MOULD BODY with two lateral water inlet/outlet for test S185-01 Ø 4” cutting collar
with piezometric measurement S200-09 Ø 6” cutting collar S200-09

Tel: +44 (0) 1442 402770

 E: [email protected]

528 RETURN TO HOMEPAGE

SECTION S | SOIL

CONSOLIDATION TEST
STANDARDS: ASTM D2435, D3877, D4546 | BS 1377:5
AASHTO T216 | XP P94 090-1, P94-091
UNE 103-405, 103-602
The one-dimensional consolidation test of a soil sample enables
to ascertain the settlement characteristic over a given period of S260
time. The soil specimen under test is axially loaded and laterally with cell and dial gauge
contained.
Loads are applied with progressive increases and the settlement
values are read on a dial gauge or on a digital display (through a
displacement transducer).
Two different oedometer models are proposed:
S260 Front loading oedometer with dial gauge or digital data
acquisition system.
S262N Edotronic, pneumatic, fully automatic touch-screen
consolidation apparatus (see next pages).
S260
FRONT LOADING OEDOMETER
CONSOLIDATION APPARATUS
Rigidly manufactured from aluminium alloy casting to provide a high
degree of accuracy with any frame distorsion under load. The load
bridge group is supported in high accuracy self-aligning seat balls.
The beam provides three loading ratio: 9:1 10:1 11:1 and the
beam assembly is fitted with an adjustable counterbalance
weight.
Maximun load: 170 kg of slotted weights, corresponding
to 1870 kg using the beam ratio 11:1
The oedometer accepts cells up to 100 cm²
Supplied complete with rod holding the weights and
coupling block holding the dial gauge or transducer.
Supplied without: consolidation cell, weights, dial gauge
(or transducer), holding bench which have to be ordered
separately.
S336-11
Weight: 25 kg approx.

ACCESSORIES

S376 DIAL GAUGE 10 mm

travel x 0.01 mm subdiv.
for vertical displacements. S334
or:
S375-01 DIAL GAUGE 12 mm
travel x 0.002 mm subdiv.
S260 with cell and S334 Cyber-Plus 8 Evolution

S334
CYBER-PLUS 8 EVOLUTION
Alternative solution:
8 channels acquisition and processing data system (expandable to
S336-11 LINEAR VERTICAL DISPLACEMENT TRANSDUCER, 16 channels) colour “Touch Screen” display, it automatically per-
10 mm travel forms test and data processing. Directly connected to PC via USB, it
S336-30 EXTENSION CABLE 2 metres long, or: prints the test certificate. Equipped with slots for external Pendrive
S336-31 EXTENSION CABLE 5 meters long, or: or SD Card infinite memory supports.
S336-32 EXTENSION CABLE 10 meters long Technical details: see p. 000, Hardware details at p. 00

S337-51 S260-05N
CALIBRATION process of the displacement transducer to the data Software OedoLab Reports - MATEST MADE
acquisition unit of the oedometer. Technical Data: see p. 000

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 529

SECTION S | SOIL

CONSOLIDATION CELLS - FIXED RING

Made from brass, with specimen holding fixed ring having cutting rim so as to be utilized also to sample undisturbed specimens.
Accurately manufactured these cells are supplied complete with loading piston, couple of porous stones and plexiglass transparent water jacket.

Model Specimen Specimen Specimen Spare Specimen Spare couple

diameter mm area cm² thickness mm cutting ring mm tamper of porous stones
S268 50.47 20 20 S122 S123 S274 KIT
S268-05 63.5 31.67 20 S122-19 S123-05 S274-10 KIT
S268-01 71.40 40 20 S122-01 S123-01 S274-01 KIT
S268-04 75.00 44.16 20 S122-17 S123-04 S274-09 KIT
S268-02 79.80 50 20 S122-02 S123-02 S274-02 KIT
S268-03* 112.80 100 25 S122-03 S123-03 S274-03 KIT
* The consolidation cell Ø 112.8 mm is made from aluminium.

S268-03

S268 disassembled S268 S268-01

CONSOLIDATION CELLS - PERMEABILITY ATTACHMENT

Made from brass, similar in manufacture to the fixed ring cells, they are also provided of a pipe connector with cock and graduated glass
burette 10 ml capacity allowing to perform permeability tests.

Model Specimen Specimen Specimen Hollow Specimen Spare couple of

Ø mm area cm² thickness mm punch tamper porous stones
S272 50.47 20 20 S122-04 S123 S274-04 KIT
S272-05 63.5 31.67 20 S122-20 S123-05 S274-11 KIT
S272-01 71.40 40 20 S122-05 S123-01 S274-05 KIT
S272-04 75.00 44.16 20 S122-18 S123-04 S274-08 KIT
S272-02 79.80 50 20 S122-06 S123-02 S274-06 KIT
S272-03* 112.80 100 25 S122-07 S123-03 S274-07 KIT

* The consolidation cell Ø 112.8 mm is made from aluminium.

S275
PERMEABILITY ATTACHMENT
Complete with stand, clamps and hose it is connected to the cells mod. S272 to S272-05.
Recommended for soil samples having great value of permeability.
Burette has 50 ml capacity and subdiv. 0.1 ml.
Weight: 5 kg approx.

S122 S123

S376
S274 KIT S272 disassembled S272 S272 + S275

Tel: +44 (0) 1442 402770

 E: [email protected]

530 RETURN TO HOMEPAGE

SECTION S | SOIL

OEDOMETER: ACCESSORIES

SLOTTED WEIGHTS
Steel made, painted against corrosion (mod. E066-02 brass made).

Available slotted weights:

Model Weight Model Weight
E066-02 100 g S273-07 4 kg
S273-06 250 g S273-02 5 kg
S273-05 500 g S273-08 8 kg
S273-04 1 kg S273-01 10 kg
S273-03 2 kg

KIT OF SLOTTED WEIGHTS

S273 KIT S273-01 KIT S273-02 KIT

S273-01 = 4x10 kg S273-08 = 7x8 kg S273-01 = 6x10 kg
S273-02 = 1x5 kg S273-07 = 1x4 kg S273-02 = 3x5 kg
S273-03 = 2x2 kg S273-03 = 1x2 kg S273-03 = 1x2 kg
S273-04 = 1x1 kg S273-04 = 1x1 kg S273-04 = 1x1 kg
S273-05 = 1x500 g S273-05 = 3x500 g
S273-06 = 2x250 g S273-06 = 2x250 g
TOTAL: 50 kg TOTAL: 64 kg TOTAL: 80 kg

HOLDING BENCH, made from sturdy structural painted steel,

complete with locking bolts and nuts.
S265 BENCH HOLDING one apparatus
S265-01 BENCH HOLDING three apparatuses

GAUGE BLOCKS
GRADE 1 S265
Used to calibrate the linear displacement transducers.

AVAILABLE MODELS SPARES

S336-41 GAUGE BLOCK, nominal S335-15 Universal coupling pliers for dial gauge/transducer.
length 5 mm It accepts all Matest displacement transducers and dial
S336-43 GAUGE BLOCK, nominal gauges (Ø from 8 to 20 mm)
length 10 mm S260-13 Mounting device between the universal coupling pliers
S335-15 and the consolidation apparatus to fix the trans-
ducer/dial gauge for the vertical displacement.
S336-43
S336-41

S336-30 S260-13
S335-15
S260-05N
Data import from
the CyberPlus S336-11

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 531

SECTION S | SOIL

S260-05N
SOFTWARE OEDOLAB REPORTS
STANDARDS: ASTM D2435-80 | XP P94-090-1 | BS 1377:5
OedoLab Reports is the new informatic tool which allows geotechnical laboratories to process data and to view the results obtained from oedo-
metric tests.

Used in conjunction with Cyber-Plus S334, the new features of this

software allow the users to:
- Create a test file from data entered manually or imported
- Create a project to perform calculations according to the
selected standard
- Integrate test files (from OedoLab Connect or manually entered)
to a project
- Elaborate, customize and print their test reports which can be
read without the need of a specific software.

The program can be used in a very simple and intuitive way. A dedi-
cated window allows the user to import data from a specific location
(for instance, from the Cyberplus through USB or SD card).
OedoLab Reports provides the user with a simple and flexible
graphical interface giving the possibility to view, edit and print all the
parameters involved in the oedometric tests. S260-05N Data feeding/acquisition

The input information for each stress level is the following:

- Settlements in mm.
- Time in min.

The Software allows also to enter information related to the

soil sample, among which:
- Extraction method.
- Blue value.
- Attemberg’s limits.
- Soil classification according to AASHTO/USCS/GTR.
- Particle size analysis.

Laboratory coefficients of:

- Consolidation – root method.
- Void ratio. S260-05N Test data visualization
- Water content.
- Densities.
- Compressibility.

CHARTS:
- Settlements (mm) / Time (min).
- Void ratio (%) / Applied pressure (kPa).
- Passing (%) / Opening (mm).

PC specification:
- Operating system: Windows XP or more recent

S260-05N Results preview

Tel: +44 (0) 1442 402770

 E: [email protected]

532 RETURN TO HOMEPAGE

SECTION S | SOIL

BUYER’S GUIDE FOR ONE STANDARD CONSOLIDATION SYSTEM AND ONE AUTOMATIC CONSOLIDATION
DATA ACQUISITION/PROCESSING SYSTEM.

S260
with accessories

S334

S265-01

Configuration for one standard Oedometer apparatus Model

Front loading oedometer S260
Oedometer bench (for one or three oedometers) S265 / S265-01
Dial gauge S376 / S375-01
Consolidation cell, fixed ring S268 / S268-05
Spare cutting ring (to combine to the consolidation cell) S122 / S122-19
Specimen tamper (to combine to the consolidation cell) S123 / S123-05
Spare porous stones (to combine to the consolidation cell) S274 / S274-10
Set of slotted weights S273 / S273-10

Permeability measurement:
Permeability consolidation cell S272 / S272-05
Permeability attachment (50 ml burette) S275
Hollow punch (to combine to the consolidation cell) S122-04 / S122-20
Spare porous stones (to combine to the consolidation cell) S274-04 / S274-11

Configuration for one Oedometer apparatus with electronic measurement and data acquisition/processing: Model
Oedometer with accessories as listed in the standard configuration (without the dial gauge S376),
and also:
Cyber-Plus 8 Evolution, 8 channels (expandable to 16 channels) automatic data acquisition/processing S334
Displacement transducer (in quantities as the oedometers) S336-11
Extension cable (in quantities as the transducers) S336-30 / S336-32
Software OedoLab Reports - Matest made S260-05N
Gauge blocks to calibrate the transducers S336-41 / S336-43
or:
Transducer / 0edometer calibration process S337-51

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 533

SECTION S | SOIL

MODULARITY TEST OPTION

S262-12N Modularity View

Oedolab Connect S262-12N allows automatic data acquisition and control for each oedometer configured into the dedicated Pneumatic Oedom-
eter control settings window (see above image).
This way, up to 24 units can be connected to the same PC by using an Ethernet network (accessories at pag. 000 of the catalogue), providing
modern geotechnical laboratories with a powerful tool to control single or multiple units at choice.

ACCESSORIES

S334-11 Network connection RS45 cable

S334-12 Switch to connect from 2 to 7 Cyber-plus units to the Ethernet Network

Tel: +44 (0) 1442 402770

 E: [email protected]

534 RETURN TO HOMEPAGE

SECTION S | SOIL

S262N
EDOTRONIC
AUTOMATIC CONSOLIDATION APPARATUS (OEDOMETER)
TOUCH SCREEN HIGH PERFORMANCE
STANDARD: ASTM D2435-80 | CEN - ISO - TS 17892-5 | BS 1377:5
This automatic consolidation system, ideal for modern and efficient laboratories, has been created to eliminate or reduce to the absolute mini-
mum any forms of manual intervention, which the oedometer test requires. This therefore results in greater efficiency and cost effectiveness.
This appliance is extremely simple and easy to use.

Frame Specifications:
Edotronic, equipped with two coaxial cylinders, provides a precise
and timely weight positioning with two ranges of measurement:
0 – 1499 (N) Newton
1500 – 15000 (N) Newton
Input of compressed air (filtered): Max. 10 Bar
Resolution: 1 Newton
Precision: 0.5%...1%
Maximum load: 15 kN (with 10 Bar input)
There is no need of weights as the cylinder and pneumatic piston
take it to the desired weight in real time.
Weight application and removal are carried out automatically in the
test sequences.
The load value is measured by a pressure transducer which is built
in the regulation valve.
An additional high precision load cell will detect the effective load
value and perform precise control through a closed loop system,
granting repeatability and accuracy.

Firmware:
- Electronic control unit Cyber-plus Evolution with “Touch-Screen”
color graphic display ¼ VGA, that runs like a standard PC based
on Windows operating system, for the management of the data.
- The Touch-Screen icon interface allows an easy set-up of all the
parameters and prompt execution of the test. Read value results
are immediate and of extreme accuracy.
- On request the machine can perform the tests without any exter-
nal PC, because of the “Cyber-Plus” grants performances like a
PC.
- Direct connection to Intranet (connection to a LAN network) and
Internet to establish a remote communication and receive an S262N with accessories
immediate diagnosis from Matest technicians, or for upgrades of
the Firmware.
- Unlimited memory storage with: 2 USB ports, 1 SD card. ACCESSORIES
- Simple, rapid linearisation and calibration procedure.
- The appliance comes completely equipped with the relevant S262-12N SOFTWARE OEDOLAB CONNECT – MATEST MADE
software. Technical Data: see next page
- Possibility to select different languages. V207 LABORATORY COMPRESSOR, tank capacity 50 litres,
- Hardware technical details: see p. 00 nominal pressure 10 Bar.
The following are not included: software oedolab connect, consol- S262-11 AIR FILTER, auto-draining, it reduces up to one micron,
idation cell, transducer, compressor, filter, that have to be ordered complete with discharge.
separately (see accessories). S336-11 LINEAR DISPLACEMENT-DEFORMATION TRANSDUCER,
Power supply: 230V 1ph 50/60Hz accurate and versatile.
Dimensions: 290x450xh 610 mm Transducer 10 mm travel.
Weight: 30 kg approx. Indipendent linearity < 0.3%
S337-51 Calibration process of the linear displacement trans-
ducer combined with the Edotronic.
S268 | S272-05 CONSOLIDATION CELLS, diffferent models:
see p. 000

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 535

SECTION S | SOIL

S262-12N
SOFTWARE OEDOLAB CONNECT
STANDARD: ASTM D2435-80 | XP P094-090-1 | BS 1377:5
To be used with the Edotronic mod. S262
OedoLab Connect is an extension of the OedoLab Reports S262-05N software, specifically designed to guide the user through
the entire consolidation test.
This software allows automatic data acquisition and to save the results in a specific file.
Thus, the file obtained can be then added to a project created with OedoLab Reports, providing the users not only with the same features given
by the S262-05N but also with new ones.
OedoLab Connect can be connected to one or more pneumatic oedometers, allowing automatic data acquistion and control during the test.
Each oedometer is controlled by the PC via network connection.
OedoLab Connect provides the user with a simple and flexible graphical interface. A dedicated window allows to select the oedometer the user
wants to work with.
Once a consolidation step is completed, the software automatically shifts to the next level; hence re-performing all the control and acquisition
operations needed to complete the test. Furthermore, by setting test parameters which are included in the Software and dedicated to the loading
sequences control (minimum speed of settlement and swelling threshold), the user is also able to program the test and save a lot of time then.
PC specification:
Operating system: Windows XP or more recent.
Supplied complete with connection cable.

S262-12N Test view S262-12N Control settings

S262-12N Acquisition settings S262-12N Information about the test

Tel: +44 (0) 1442 402770

 E: [email protected]

536 RETURN TO HOMEPAGE

SECTION S | SOIL

DIRECT / RESIDUAL SHEAR TEST APPARATUS, DIGITAL TOUCH-SCREEN

STANDARDS: ASTM D3080 | BS 1377:7 | NF P94-071-1, NF P094-071-2 | AASHTO T235 | CEN-ISO-TS 17892-10
This apparatus is used to determine the resistance to shearing of all types of soil specimens including both consolidated and drained, undis-
turbed or remolded. The machine can accommodate round specimens Ø 50, 60, 63.5, 100 mm and square 60x60, 10x100 mm.
The machine has an integral closed loop control motor with epicycloid reducers.
At the beginning of each test the machine performs an automatic and complete internal check including a position reset resulting in the elimina-
tion of all position errors.
A user-friendly microprocessor controlled touch screen is used to input all test patterns providing an efficient and flexible interface.
(All data are input and stored when the machine is in stand-by, without affecting the specimen under test with quick machine setting.)
Facility for shear box maximum extension detection, to automatically stop the test.
Facility to input a different return speed (residual shear) in relation to the one used for the shear test, thus allowing a quick playback of the
residual shear test, saving a lot of time.
The effects of the primary consolidation can be identified directly on the consolidation curve, only with data acquisition version. Automatic
calculation of the appropriate shear velocity with selection of optimal consolidation parameters for t50, t90 and t100 (only with data acquisition
version). This provides efficiency and cost effectiveness.

Frame Specifications:
- Maximum shear load: 5000 N possible on the whole speed range. MAIN FEATURES
- Shear speed: 0.00001 to 15,0000 mm/min.
- Display of both speed and displacement with 0.00001 mm Automatic calculation of the appropriate shear
resolution. velocity based on optimal consolidation parameters.
- Possibility of direct vertical load, or with a lever arm ratio 10:1 Shear speed: 0.00001 to 15,0000 mm/min
- Max vertical direct load: 500N; lever arm: 5500N
- Box group mounted on ball track with high quality antifriction Different return speed facility for residual shaer test.
system. Integral closed loop control motor.
- Extremely easy and practical use, not requiring qualified staff.
User-friendly microprocessor controlled touch screen.
Firmware: 8 connectors for acquisition and data processing
- Electronic control unit Cyber-plus Evolution with system.
Touch-Screen color graphic display ¼ VGA, that runs like a stand-
ard PC based on Windows operating system, for the management
of the data. (Analysis of the data, test results, graphs with S277-
40N Software; optional accessory).
- The Touch-Screen icon interface allows an easy set-up of all the
parameters and prompt execution of the test. Read value results
are immediate and of extreme accuracy.
- The machine can perform the tests without any external PC,
because of the Cyber-Plus grants performances like a PC.
- Direct connection to Intranet (connection to a LAN network) and
Internet to establish a remote communication and receive an
immediate diagnosis from Matest technicians, or for upgrades of
the Firmware.
- Unlimited memory storage with: 2 USB ports, 1 SD card.
- Possibility to select different languages.
- Hardware technical details: see page 24
- The machine is equipped with 8 connectors for the acquisition
and data processing system (3 analogical/digital channels are
activated with the S277-31 optional firmware for load cell and
transducers; and 5 channels can be activated with the S277-32
optional firmware).
Power supply: 230V 1ph 50-60Hz 200W
Dimensions: 1040x420xh1350 mm
Weight: 120 kg approx.

S276 KIT + S284

Detail of the 8 connectors

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 537

SECTION S | SOIL

THE DIRECT/RESIDUAL SHEAR TESTING MACHINE IS AVAILABLE IN THREE VERSIONS

S276 KIT
SHEARLAB DIGITAL BASIC VERSION
DIGITAL SHEAR TESTING MACHINE
comprising:
S276-10 Shear Frame, with digital Touch-Screen microprocessor, complete with beam loading device, shear box case with adaptors, dial
gauge supports.
S370-03S Load Ring, 3000N capacity with electric safety stop device (load rings of different capacities up to 5000N available on request).
S377 Dial indicator 25mm x 0.01mm for horizontal displacement.
S376 Dial indicator 10mm x 0.01mm for vertical displacement.
S273 KIT Set of 50 kg of slotted weights.
Note: Shear box, hollow punch, tamper are not included and have to be ordered separately (see accessories)

S276-01
AUTO SHEARLAB DATA ACQUISITION VERSION
DIGITAL SHEAR TESTING MACHINE WITH INCORPORATED DATA ACQUISITION SYSTEM AND BASIC FIRMWARE
comprising:
S276-10 Shear Frame with digital Touch-Screen microproces-
sor, complete with beam loading device, shear box
case with adaptors, transducers supports.
S277-20 Load Cell, electric, 3000N capacity, complete with
cable.
S336-11 Linear vertical transducer, 10 mm travel.
S336-12 Linear horizontal transducer, 25 mm travel.
S277-31 Firmware activating 3 connectors for basic data acqui-
sition.
S273 KIT Set of 50 kg of slotted weights.
Note: Shear box, hollow punch, tamper and Software
(see next pages) are not included and have to be
ordered separately.

ACCESSORIES

S277-40N SOFTWARE SHEAR-LAB REPORTS - MATEST MADE

Technical data: see p. 000
S277-32 FIRMWARE activating 5 connectors foreseen on the
shear frame S277-10N. They can be used as data
acquisition and processing system for geotechnical
tests. Technical data: see S334 p. 000
Note: these 5 channels can be used alternatively (not simulta-
neously) to the 3 channels of the shear frame.

GAUGE BLOCKS. Grade 1 S276-01 + S284

Used to calibrate the linear displacement transducers (see p. 000)

SPARES

S335-15 Universal coupling pliers for dial gauge/transducer.

It accepts all Matest displacement transducers and dial S277-20
S336-31
gauges (Ø from 8 to 20 mm)
S280-15 Mounting device between the universal coupling pliers
S335-15 and the shear machine to fix the vertical
displacement transducer or dial gauge.
S280-16 Mounting device between the universal coupling pliers S335-15
S335-15 and the shear machine to fix the horizontal S336-11
displacement transducer or dial gauge. S336-12 S280-16
S280-15

Tel: +44 (0) 1442 402770

 E: [email protected]

538 RETURN TO HOMEPAGE

SECTION S | SOIL

HOLLOW PUNCH (sample cutter) and

ACCESSORIES
TAMPER (extrusion tool)
SHEAR BOX assemblies, made from brass, accurately machined, The hollow punch with cutting rim is used to prepare the soil
complete with carriage, walled round or square hole, base plate, sample, and the tamper ejects the specimen filling it directly into
two grids, two perforated grids, two porous stones, adapters to fit the shear box without disturbing it.
the box holder.
Models Shear box Spare couple Models Hollow punch Tamper
of porous
stones
Round specimens Ø 50 mm S282 S286-03 KIT Ø 50xh 23 mm S122-08 S123-08
Round specimens Ø 60 mm S283 S286 KIT Ø 60xh 23 mm S122-09 S123-09
Round specimens Ø 63.5 S283-01 S286-05 KIT Ø 63.5xh 23 mm S122-21 S123-17
Round specimens Ø 100 mm S281 S286-04 KIT Ø 100xh 23 mm S122-10 S123-10
Square specimens 60x60 mm S284 S286-01 KIT Square 60x60xh 23 mm S122-11 S123-11
Square specimens 100x100 mm S285 S286-02 KIT Square 100x100xh 23 mm S122-12 S123-12

S281
S282
S285
S122-10
S123-10
S284
S286-03 S122-11
S283
S123-11

S286-02 KIT

S286-04 KIT S286 KIT S286-01 KIT

S290 Note: On request the shear machine can be equipped with load
CONSOLIDATION FRAME rings or load cells having capacity from 500 N to 5000 N:
It accepts up to 3 shear boxes or consolidation cells.
Used to applly a constant load on the specimen in the shear box, so
as to shorten the test duration when a lot of specimens have to be
tested and just few shear machines are available. The frame can
also be used to consolidate oedometric cells. Produced in a rugged
steel structure, it is supplied complete with three lever arms ratio
10:1 having each max. load up to 550 kg, centering devices and ACCESSORIES for S290
dial gauge holders. Supplied without weights, water container, cells
S291 WATER CONTAINER, made from plexiglass and alumin-
and dial gauges to be ordered separately.
ium, it accomadates the shear box up to max size
Dimensions: 2300x450x900 mm Ø 60 mm or 60 mm during the consolidation test, by
Weight: 150 kg approx. keeping the specimen deep into the water.
S291-01 WATER CONTAINER, it accomodates all the shear boxes
up to Ø 100 mm or 100 mm size.
S273 KIT Set of 50 kg of slotted weights
S376 Dial gauge 10x0.01 mm

S290 with accessories

S291-01 S291

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 539

SECTION S | SOIL

S277-40N
SOFTWARE SHEARLAB REPORTS
STANDARDS: ASTM D3080-72 | NF P94-071-1 | NF P94-071-2
BS 1377:7
To be used with the shear testing machine, data acquisition
processing version, mod. S276-01
ShearLab Reports is the new informatic tool which allows geotech-
nical laboratories to process data and to view the results obtained
from direct and residual shear tests.

The new features of this software allow the users to:

- Create a test file from data entered manually or imported
- Create a project to perform calculations according to the
selected standard
- Integrate test files to a project
- Elaborate, customize and print their test reports which can be S277-40N Data import
read without the need of a specific software

The program can be used in a very simple and intuitive way.

A dedicated window allows the user to import data in the test file.
ShearLab Reports provides the user with a simple and flexible
graphical interface giving the possibility to view, edit and print all the
parameters involved in shear tests.

The input information is the following:

- Settlement in mm
- Time in min
- Horizontal displacement in mm
- Force in kN

In the project management window, the Software automati-

cally calculates the shear parameters:
- Peak strength in kPa
- Residual strength in kPa
- Peak displacement in mm
- Residual displacement in mm S277-40N Test data calculation

Laboratory coefficients of:

- Water content
- Densities
- Void ratio
ShearLab Reports automatically draws the curves of shear and
compaction, hence performing all the calculations required by the
standard. Comments on the current project can also be added if
necessary.

CHARTS:
- Shear stress (kPa) / Horizontal displacement (mm)
- Settlement (mm) / Horizontal displacement (mm)
- Shear strength (kPa) / Normal stress (kPa)

PC specification:
- Operating system: Windows XP or more recent.
Supplied complete with connection cable

S277-40N Results preview

Tel: +44 (0) 1442 402770

 E: [email protected]

540 RETURN TO HOMEPAGE

SECTION S | SOIL

S276-02
SHEARTRONIC
DIGITAL SHEAR TESTING MACHINE WITH INCORPORATED DATA ACQUISITION SYSTEM AND PNEUMATIC
VERTICAL LOADING DEVICE - FULLY AUTOMATIC HIGH PERFORMANCE

S276-02 + S284

Sheartronic High Performance is an advanced system specifically designed to perform consolidation, direct and residual shear stages in a
fully automated way. The system is based on a pneumatic closed-loop system which along with a high-performance regulator guarantees an
automatic application of a vertical load up to 6000N, thus offering the unique possibility to reduce to the absolute minimum any form of manual
intervention (no need of dead weights or level arms).

SHEARTRONIC SYSTEM INCLUDES:

TECHNICAL SPECIFICATIONS
S276-11 Shear frame with digital touch-screen microprocessor,
Maximum horizontal force: 5000 N complete with pneumatic vertical loading device, shear
box case with adaptors, transducers supports.
Maximum travel: 20 mm S277-20 Load cell, electric, 3000 N capacity, complete with
Shear speed: 0.00001 to 15.0000 mm/min cable (5000N cell available on request).
Maximum vertical load: 6000 N (more than 600 kPa on a 100 x 100 S336-11 Linear vertical transducer, 10 mm travel
mm square specimen) applied by a pneumatic piston controlled by S336-12 Linear horizontal transducer, 25 mm travel
a closed loop system with a 10 bar pressure transducer S277-31 Firmware activating 3 connectors for basic data
Max air pressure supply: 10 bar acquisition
Technical specifications of the frame and firmware: see p. 00
Max working air pressure: 8 bar
Power supply: 230V 1ph 50-60Hz 200W
Dimensions: 1030x400x580 mm
Weight: 100 kg approx.

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 541

SECTION S | SOIL

FIRMWARE

Similar to S276 KIT and S276-01 machines but with the new
possibility to identify directly on the consolidation curve the effects
of the primary consolidation. Sheartronic High Performance
automatically calculates the appropriate shear velocity to be
applied to the specimen by selecting the optimal consolidation
parameter among t50, t90 and t100, improving efficiency and cost
effectiveness.

Note:
1. shear box, hollow punch, tamper (see accessories) and Software
S277-41N are not included and have to be ordered separately
2. The pneumatic shear machine mod. S276-02 requires an air
compressed source.
3. The machine is configured to accommodate an additional piston
to apply a max vertical load of 10000 N

V207
RECOMMEND ACCESSORIES

S262-11 AIR FILTER, auto-draining, it reduces up to one micron,

complete with discharge
S277-41N SOFTWARE SHEAR LAB CONNECT
For fully automatic data control, acquisition, processing and
visualization in direct/residual shear tests, with graphics on all the
test phases (technical details: see p. 000)

ACCESSORY

V207 LABORATORY AIR COMPRESSOR, 50 litres capacity, 10

bar nominal pressure

S336-41 S336-43 S336-45 S336-47

GAUGE BLOCKS. Grade 1

Used to calibrate the linear displacement transducers.

Available models:
S336-41 Gauge block, nominal length 5 mm
S336-43 Gauge block, nominal length 10 mm
S336-45 Gauge block, nominal length 25 mm

SPARES

S335-15 Universal coupling pliers for dial gauge/transducer. It

accepts all Matest displacement transducers and dial
gauges (dia. from 8 to 20 mm)
S335-15
S280-15 Mounting device between the universal coupling pliers
S335-15 and the shear machine to fix the vertical
displacement transducer or dial gauge
S280-16
S280-16 Mounting device between the universal coupling pliers S280-15
S335-15 and the shear machine to fix the horizontal
displacement transducer or dial gauge

Tel: +44 (0) 1442 402770

 E: [email protected]

542 RETURN TO HOMEPAGE

SECTION S | SOIL

S277-41N
SOFTWARE SHEARLAB CONNECT
STANDARDS: ASTM D3080 | NF P94-071-1, P94-071-2 | BS 1377:7
ShearLab Connect is an extension of the ShearLab Reports S277-40N software, specifically designed for automatic data control,
acquisition, processing and visualization of direct/residual shear tests.

The file obtained can be then added to a project created with ShearLab Reports S277-40N, which features are detailed on p. 000

The program can be used in a very simple and intuitive way; a dedicated window allows to select the machine the user wants to work with while
a test-specific setup guides the acquisition process, including data collection parameters that best fit the specific test. All test-specific initial,
intermediate and final parameters are calculated based on input of specimen information, such as sample type (cylindric or square), sample
diameter or width (mm), initial height of sample (mm), initial and final wet masses (g), dried mass after oven (g), applied load (kg), grain density
(kg/m³), consolidation time (min).

ShearLab Connect can be connected to one or more shearing machines, thus allowing automatic data control and acquisition during the test.
Each Sheartronic is connected via LAN or serial cable to the PC

S277-41N Test-specific parameters S277-41N Test-specific parameters

Displayed CHARTS (by selecting 2 of the following parameters):

- Time (s)
- Applied force (kN)
- Horizontal displacement (mm)
- Vertical displacement (mm)

PC specification:
- Operating system: Windows XP or more recent
Supplied complete with LAN cable.

277-41N Control settings

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 543

SECTION S | SOIL

TRIAXIAL TESTS
STANDARDS: BS 1377:8 | ASTM D2850, ASTM D4767, ASTM D7181 | NF P94-070, NF P94-074 | CEN-ISO | TS 17892-8.9
Introduction
A knowledge of stress-strain behaviour and the shear strength parameters of soils is required when soil is interacting with structures or
when soil is used as a construction material in many engineering purposes such as:

1. Excavations
2. Shallow foundations
3. Piles and deep foundations
4. Earth retaining structures, diaphragm walls, anchors
5. Slope stability
6. Ground improvement
7. Design of embankments, earth dams
“CU” consolidated undrained test
The most widely used testing apparatus for investigating the stress-
This test is used in order to estimate the drained and undrained
strain behaviour and the strength parameters of soils is the triaxial
shear strength parameters (effective cohesion c’, effective friction
apparatus.
angle φ’, and undrained shear strength cu). It is usually performed
on fine grained soils. In this test, the first phase is carried out
Triaxial tests are typically performed with two stages: an isotropic
with an open drainage valve in order to allow the consolidation and
loading followed by shear loading which is carried out up to failure.
volume change to occur. During the second phase, the drainage
A cylindrical saturated soil sample, undisturbed or reconstituted,
valve is closed and the change of pore water pressure is measured;
is placed in a rubber membrane in order to isolate it from direct
there is no volume change and distortions occur up to failure. It
contact with the surrounding water with which the testing cell is
gives three values of undrained shear strength, which are the radii
filled, and which is pressurized. The sample sits in the cell between
of the Mohr’s circles, and the values of the effective cohesion and
a rigid base and a rigid top cap and is loaded by means of a ram, at
of the effective friction angle, which are derived from the envelope
a constant speed. The water drainage in or out the sample can be
of the effective stress Mohr’s circles. The stress-strain behaviour
allowed by means of opening or closing a valve.
and the strength parameters are then used to model engineering
The two phases are carried out under different combinations of
problems when undrained conditions are present, after consolida-
drainage conditions and give rise to 3 different standard triaxial
tion processes or in long term applications.
tests. Each test is usually performed on three saturated specimens
at three different confining pressures.

“CD” consolidated drained test

SAMPLE

This test is used in order to estimate the effective shear strength

parameters (effective cohesion c’, effective friction angle φ’). It is
usually performed on coarse grained soils. In this test, both phases
CELL PRESSURE DRAINAGE are carried out with the drainage valve open. Volume change occurs
PORE PRESSURE in both phases and during the second phase, distortions occur up
to failure. The CD test gives the values of the effective cohesion and
of the effective friction angle, which are derived from the envelope
“UU” unconsolidated undrained test
of effective stress Mohr’s circles. The stress-strain behaviour and
This test is used in order to estimate the undrained shear strength
the strength parameters are then used to model engineering prob-
parameters (undrained shear strength cu and undrained friction
lems when drained conditions are present, typically in long term
angle φu = 0). It is usually performed on fine grained soils. In this
design.
test, both phases are carried out with the drainage valve closed. No
volume change is allowed during the test and distortions during the
shear phase occur up to the failure. This test gives a unique value
of undrained shear strength, as the envelope of the Mohr circles
plotted in total stresses is horizontal. The angle φu has to be zero
or it is an error in the test, e.g. poor saturation.
The stress-strain behaviour and the strength parameters are then
used to model engineering problems when undrained conditions
are present, typically in short term design.

Tel: +44 (0) 1442 402770

 E: [email protected]

544 RETURN TO HOMEPAGE

SECTION S | SOIL

S301N
TRIAXIAL LOAD FRAME 50KN, DIGITAL TOUCH-SCREEN
This versatile, compact, heavy duty load frame has been designed for routine tests,
for central laboratories, but also for research purposes.
The frame is of rigid chromed steel twin column construction.
The electronic color digital touch-screen display with microprocessor control system allows
to perform tests within a speed range of 0.00001 to 12 mm/min.
The maximum load capacity is 50 kN, and it is suitable either for cells S305
(max. specimen size 70x140mm) and S306 (max. specimen size 100x200mm),
Matest or other manufacturers made. The system guarantees high resolutions in real time.
The load plate is foreseen of electric end of stroke, to save the machine from wrong manip-
ulations.
Frame Specifications:
- Maximum load capacity: 50kN
- Infinitesimal testing speed: from 0.00001 to 12 mm/min.
- Minimum vertical clearance: 400 mm (140 mm with ring)
- Maximum vertical clearance: 1100 mm (840 mm with ring)
- Horizontal clearance: 380 mm
- Platen diameter: 177 mm

Firmware:
- Electronic control unit “Cyber-plus Evolution” with Touch-Screen color graphic
display ¼ VGA, that runs like a standard PC based on Windows operating system
for the management of the data. (Analysis of the data, test results, graphs with
S335-10N software; optional accessory).
- The Touch-Screen icon interface allows an easy set-up of the parameters and
immediate execution of the test.
- The machine can perform the tests without any external PC, because of the
“Cyber-Plus” grants performances like a PC.
- Direct connection to Intranet (connection to a LAN network) and Internet to estab-
lish a remote communication and receive an immediate diagnosis from
Matest technicians, or for upgrades of the Firmware.
- Unlimited memory storage with: 2 USB ports, 1 SD card.
- Possibility to select different languages.
- Hardware technical details: see p. 00
- The machine is equipped with 8 connectors for the acquisition and data process-
ing system up to 8 analogical/digital channels (that is activated with the S301-05 S301N with data acquisition
optional firmware) for load cells and transducers. Extra slot available to expand the
on-board channels to 16 (with S301- 06)
The frame is supplied with loading ram and sphere, but without load rings, dial gauges, electric load cells
or displacement transducers that have to be ordered separately (see next pages).
Power supply: 230V 1ph 50-60Hz 600W
Dimensions: 490x510xh1800 mm
Weight: 115 kg approx.

Note: Triaxial load frame 50kN is available also with wider variable speed
NEW range from 0.00001 to 100 mm/min. See model S301-02 at pag. 000.

Detail of the 8 connectors

UPGRADING ACCESSORIES

S301-05 FIRMWARE FOR ACQUISITION AND DATA PROCESSING

system up to 8 analogical/digital channels for load cells and transducers.
Graphic and numbers visualization, processing, printing and storing of the test results.
This software activates the 8 connectors foreseen on the load frame.
S301-06 8-CHANNEL INTERNAL MODULE, for system expansion to 16 channels of the triaxial load
frame. This upgrade is possible only in Matest factory.
S301N with load ring S335-10N SOFTWARE TRIAXLAB CONNECT & REPORTS See p. 000

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 545

SECTION S | SOIL

S301-02
TRIAXIAL LOAD FRAME 50 KN
EXPANDED VARIABLE SPEED RANGE
Matest S301-02 is the new high performance load frame specifically designed for advanced laboratories where maximum testing speed up to
100 mm/min is desired.
The expected variable speed range of this electro-mechanical machine makes it suitable to perform Unconfined, CBR and Marshall tests other
than standard triaxial on soil specimens up to 150 mm diameter.
This heavy duty load frame has provision for automatic load or
displacement/deformation control and employs new technologies
to precisely follow the shape with elegantly rounded corners.
A touch-orientable display, front mounted, allows an easy and
innovative control of the main functions and data acquisition.

MAIN FEATURES

Maximum testing speed: 100 mm/min

Maximum specimen diameter: 150 mm
Maximum compression capacity: 50kN
Innovative shape with elegantly rounded corners
Touch-orientable high-resolution display
Suitable to perform Unconfined, CBR, Marshall and
Standard Triaxial tests

S301-02

TECHNICAL SPECIFICATIONS

MODELS S301-02 (NEW) S301N

Maximum Sample Diameter, mm 150 150

Minimum testing speed, mm/min 0.00001 0.00001
Maximum testing speed, mm/min 100 12
Maximum compression force, kN 50 50
Minimum vertical clearance, mm 390 400
Maximum vertical clearance, mm 1110 1100
Horizontal clearance, mm 380 380
Platen diameter, mm 177 177
Platen travel, mm 100 100
Dimensions, mm (h x w x d) (approx.) 1675x50 x530 1800x490x510
Power supply: 230V 1ph 50/60Hz 1500W 230V 1ph 50/60Hz 600W
Weight, kg (approx.) 130 115

Tel: +44 (0) 1442 402770

 E: [email protected]

546 RETURN TO HOMEPAGE

SECTION S | SOIL

TRIAXIAL CELLS
Triaxial cells are provided in two different dimensions, mod. S305
and S306. Top and low cell caps are made in aluminium corodal alloy
and the transparent cell cylinder is in high resistant acrylic material.
The cell can be easily assembled and disassembled by means of
quick clamping rods. In order to reduce as much as possible friction,
a particular care is deserved during loading ram realisation. The low
cell cap is supplied with “four inlet valves”: back pressure, low drain-
age, pore pressure, cell pressure.
In order to measure the specimen axial deformation, an adjustable
dial gauge or a displacement transducer is also provided.

Note: No top caps, base adapters, rubber membranes and seal-

ing rings, porous stones, dial gauges, etc. are included
and should be ordered separately. In the table all
accessories for triaxial cells are listed.

S305 WITH ACCESSORIES S306

Models S305 S306
Max. specimen size mm Ø 70x140 Ø 100x200 Note: Cell S305 can be also used also for specimens having
Max. cell pressure 1700 kPa 1700 kPa diameter 50x100 and 38x76 mm with accessories of
Overal dimensions mm Ø 280x480 Ø 310x540 suitable diameter, but it is not suitable for 100x200 mm
samples.
Weight kg 8 16
Note: Cell S306 can be also used also for specimens having
diameter 70x140, 50x100 and 38x76 mm with accesso-
MAXIMUM REACHABLE VERTICAL TOTAL STRESS: ries of suitable diameter.
Sample Ø 38x76 mm Ø 50x100 mm Ø 70x140 mm Ø 100x200 mm
Cell S305 ~ 44 MPa ~ 25 MPa ~ 13 MPa –
Cell S306 ~ 44 MPa ~ 25 MPa ~ 13 MPa ~ 6 MPa

Note: Be aware that not all proving rings or load cells are suitable for all reachable axial force. See “measure of the axial force applied” section, p. 000

Accessories for Triaxial Cells: Ø 38x76 mm Ø 50x100 mm Ø 70x140 mm Ø 100x200 mm

Rubber membrane (pack of 10) S310 S310-01 S310-02 S310-03
“O” ring (pack of 10) S311 S311-01 S311-02 S311-03
Membrane stretcher S312 S312-01 S312-02 S312-03
Split former S313 S313-01 S313-02 S313-03
Split mould NEW S313-10 S313-11 S313-12 S313-13
Top cap with drainage S314 S314-01 S314-02 S314-03
Base adapter for cell. mod. S305 S315 S315-01 S315-02 –
Base adapter for cell. mod. S306 S315-04 S315-05 S315-06 S315-07
Porous disc (2 pcs) S316 S316-01 S316-02 S316-03
Perspex plain disc (2 pcs) S317 S317-01 S317-02 S317-03
“O” ring for base adapter S318 S318-01 S318-02 S318-03
Filter paper for lateral drainage (50 pcs) S319 S319-01 S319-02 S319-03
Filter paper for base (100 pcs) S320 S320-01 S320-02 S320-03
Stainless core cutter S122-13 S122-14 S122-15 S122-16
Dolly for extraction S123-13 S123-14 S123-15 S123-16
Drainage burette, 10 ml cap. S321 S321 S321 –
Drainage burette, 50 ml cap. – – – S322
Nylon tube Ø 6x4 (20 m) S325 S325 S325 S325
Terminal for connection tube (10 pcs) S326 S326 S326 S326
Flaring tool S327 S327 S327 S327
Vaseline oil (1000 ml) S328 S328 S328 S328
Silicon grease (1 kg) S329 S329 S329 S329
Grease pump S330 S330 S330 S330
Null displacement valve (spare) S331 S331 S331 S331

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 547

SECTION S | SOIL

ACCESSORIES NEW
S313-11
RUBBER MEMBRANE, to isolate the specimen from cell water. S313-10

“O” RING, to seal the membrane around the top cap and the base
adapter.

MEMBRANE STRETCHER, to stretch the membrane during its posi-

tioning, avoiding to disturb the specimen. S313-12
S313-13
SPLIT FORMER, to prepare coarse grain soil specimens. It is made
of two aluminium halves. DOLLY FOR EXTRACTION, to extrude the specimen from the core
cutter.
SPLIT MOULD, to trim the ends of undisturbed specimens. It is
made of two aluminium halves. NEW DRAIN BURETTE, to prepare coarse grain specimens by applying a
negative pressure to the base of the specimen and to measure the
TOP CAP WITH DRAINAGE, to load the whole cross section area of water volume change in or out the specimen during testing with
specimen when drainage is required. It is made of anodized alumin- specimen open to the atmosphere. Two models are available: 10 ml
ium. Connector is provided. capacity for specimens up to 70 mm ø and 50 ml for specimens up
to 100 mm ø It is supplied with cell rod and cell couplings.
BASE ADAPTER, used to adapt the triaxial cell to the specimen
diameter. It is made of aluminium. “O” RING FOR BASE ADAPTER, to seal the membrane on the base
adapter and the top cap.
POROUS DISCS, to allow the drainage in or out of the specimen in
the whole cross sectional area, toward the top cap and the lower FLARING TOOL, to cut and prepare the ends of nylon tubes which
base. Two pieces are required. They are made of phosphor bronze. have to be fixed to the suitable connectors.

PERSPEX PLAIN DISCS, to replace porous discs in undrained tests.

Two pieces are required. They are made of 10 mm thick Perspex.

FILTER PAPER FOR LATERAL DRAINAGE, for lateral drainage on low

permeability specimens.

FILTER PAPER FOR BASE, to avoid passages of soil particles into the
porous stones.

CORE CUTTER, to cut soil cohesive specimens in correct diameters

from bigger samples. It is made of stainless steel with a cutting
edge.
S321...S331

S312
S313 S315
S122-13
S123-13

S314

S319 S320
S310

S316 S318
S311 S317

Tel: +44 (0) 1442 402770

 E: [email protected]

548 RETURN TO HOMEPAGE

SECTION S | SOIL

MEASURE OF THE AXIAL FORCE APPLIED TO THE SPECIMEN

Three different equipments are available to measure the axial
force applied to the specimen:
load proving rings (manual readings)
load cells (automatic readings)
submersible load cells (automatic readings and no friction
effects)
LOAD PROVING RINGS
Mechanical equipment for manual reading. In order to avoid any S370-03S S371-07S
overload damage, an electrical safety device is supplied to stop the
loading process when the maximum capacity of the ring is reached.
Technical details, other models and accessories see p. 000

Max Capacity Dial Gauge Dial Gauge Height Weight

load kN 0.01 mm 0.001 mm mm kg SUBMERSIBLE LOAD CELLS
1 S370-01S S371-01S 210 1.7 Submersible electrical equipment for automatic reading.
The submersible load cell must be placed inside the cell and con-
3 S370-03S S371-03S 210 1.9
nected to the automatic data acquisition system mod. S334
5 S370-04S S371-04S 210 2 (see p. 000).
10 S370-05S S371-05S 210 2.2 It is made of high quality materials. It is a sealed waterproof device
20 S370-07S S371-07S 210 3 with an excellent resistance to lateral forces.
It guarantees no friction effect of the ram. It is strongly recom-
50 S370-10S S371-10S 210 7.2 mended when high accuracy in testing is required.
It must be equipped with the loading ram mod. S337-21.
Rated output: 2 mV/V nominal
ACCESSORY Accuracy: 0.1%
Non-linearity: 0.05%
S374 STEM MECHANICAL BRAKE DEVICE
It keeps the max. reached value on the dial gauge and Models Capacity
allows the manual zero setting.
S337-02 3 kN
S337-03 5 kN
ELECTRIC STRAIN GAUGE LOAD CELLS
Electrical equipment for automatic reading. The load cell must be S337-04 10 kN
connected to the automatic data acquisition system mod. S334 S337-05 25 kN
(see p. 000). Cable, connector and device to fix the load cell to the
triaxial frame are supplied.
Rated output: 2 mV/V nominal ACCESSORIES
Accuracy: 0.1%
S337-21 LOADING RAM: Loading ram for submersible cells
Models Capacity S337-51 CALIBRATION PROCESS of one device that is combined
with the acquisition/processing system mod. S334.
S337-31 2.5 kN
To be chosen among:
S337-35 5 kN - displacement transducer mod.S336-11 to S336-22,
S337-32 10 kN - electric load cell mod. S337-02 to S337-34.
S337-33 25 kN Calibration certificate is supplied.
S337-34 50 kN

S337-04

S337-34 S337-32

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 549

SECTION S | SOIL

MEASURE OF THE AXIAL STRAIN

Two different equipments are available to measure
the specimen axial displacement:
- Dial gauges (manual readings) S335-15
or: S305-05
- Displacement transducers
(automatic readings) S336-11

S336-15
DIAL GAUGES (manual readings)
S377 Dial gauge, 25x0.01 mm suitable for specimens of max. S336-31
dimensions 50x100 mm
S379 Dial gauge, 50x0.01 mm suitable for specimens of max.
dimensions 70x140 mm Note: The displacement transducers must be connected to the
automatic data acquisition system mod. S334
S383 Dial gauge, 25.4x0.001 mm with RS 232 port for PC (see p. 000) or mod. S301-05 (see p. 000).
connection.
Note: For other requirements, dial and digital gauges with dif-
ferent maximum travel and sensibility are also available:
see technical details at p. 000.

ACCESSORIES for DISPLACEMENT TRANSDUCERS

S336-30 Extension cable 2 metres long

S336-31 Extension cable 5 metres long
S383
S336-32 Extension cable 10 metres long
S379
Note: It is recommended to use not more than 10 m of exten-
S377 sion cable to avoid noise problems that might occur.
S335-15 Universal coupling pliers to hold the transducer/dial
DISPLACEMENT TRANSDUCERS (automatic readings) gauge. It fits all Matest displacement transducers and
Electrical devices for automatic readings. Calibration certificate is dial gauges (from Ø 8 mm to 20 mm).
supplied. Cable, connector and signal conditioner are provided.
S305-05 Mounting device of the universal coupling pliers mod.
TYPES OF AVAILABLE TRANSDUCERS: S335-15 to fix the displacement transducer/dial gauge
TYPE “A”: Accurate and versatile linear potentiometric displace- to the Triaxial Cell mod. S305 or mod. S306
ment transducer,.
Indipendent linearity < 0.3% (0.3x10 mm)
Max. displacement speed: up to 10 m/s.

MODELS

S336-11 10 mm travel
S336-12 25 mm travel
S336-14 50 mm travel
S336-13 100 mm travel
S336-47
S336-43 S336-45
S336-41
TYPE “B”: Linear Strain Gauge Transducer. It guarantees good
repeatability and noise reduction.
Full bridge at 350 Ohm
Indipendent linearity < 0.1% GAUGE BLOCKS. Grade 1
Standard sensitivity: 2 mV/V Used to calibrate the linear displacement transducers.

MODELS MODELS

S336-18 5 mm travel S336-41 Nominal length 5 mm

S336-15 10 mm travel S336-43 Nominal length 10 mm
S336-16 25 mm travel S336-45 Nominal length 25 mm
S336-17 50 mm travel S336-47 Nominal length 50 mm

Tel: +44 (0) 1442 402770

 E: [email protected]

550 RETURN TO HOMEPAGE

SECTION S | SOIL

PRESSURE SYSTEMS S351N

Two different solutions are available: LABORATORY AIR COMPRESSOR
- Oil/Water motorized constant pressure system It reaches a maximum pressure of 15 bar and it must be used with
- Air/Water interface system with air pressure regulator the air/water interface cell.
(to be connected to a pneumatic compressor) Sucked air: 84 litre/minute.
Reservoir capacity: 3 litres.
A144 Power supply:
OIL/WATER CONSTANT PRESSURE SYSTEM 230V 1ph 50Hz 0.75HP
This unit provides a constant pressure from 0 to 3500 kPa by using Dimensions:
a motorized hydraulic pump, an oil/water interchange tank, ram/ 460x300x470 mm
spring, valves and connectors, high viscosity oil. Weight: 22 kg approx.
Test pressure precision gauge, range 0-3500 kPa is supplied. To be
noted that the maximum tolerable pressure in the cell is 1700 kPa. As an alternative:
Power supply: 230V 1ph 50Hz
S351N
Dimensions: 320x320x410 mm V207
Weight: 20 kg approx. LABORATORY AIR COMPRESSOR
It can be used when lower cell pressures are required, as an alter-
native to mod. S351N.
Max. pressure: 10 bar
Reservoir capacity: 50 litres
Recommended for continuous
working pressure up to 750 kPa
Power supply:
230V 1ph 50Hz
A144 Weight: 40 kg approx.
S350N
AIR/WATER BLADDER PRESSURE SYSTEM
It provides a water pressure up to 1700 kPa. Simple, practical and V207
extremely accurate system used to select test pressures, it can also S355
offer the possibility to further system expansions. DE-AIRING TANK 20 LITRES CAPACITY
The use of deaerated water is recommended. It must be connected It produces de-aired water when connected to the vacuum pump. It
to a pneumatic compressor as mod. S351N or mod. V207. is a perspex tank with an inlet water valve and an outlet air valve.
The cell set is equipped with an inlet high pressure air valve and Tank capacity: 20 litres.
2 outlet valves for pressurized water and water.
Dimensions:
Dimensions: 270x300x425 mm 320x320x520 mm
Weight: 9 kg approx. Weight: 15 kg approx.

ACCESSORIES

S350-05N PRESSURE REGULATOR, high accuracy model, to preset

and control the work pressure, complete with two outlet S355
air valves.
S355-01 FILTER UNIT (water trap) composed by filtering device ACCESSORIES
and interchangeable cartridge, used to collect moisture.
V205 VACUUM PUMP To produce vacuum up to of 0.1 mbar
SPARE (see p. 000)
V205-10 - V205-12 VACUUM REGULATOR It is supplied with
S350-04 Membrane for air/water cell. vacuum gauge, control valve, suction filter and
Pack of 2 pieces. moisture trap.
V230-03 Rubber tube. Suitable
for vacuum, 3 m V205-10

S355-01 S350-04
S350-05N Note:
Other models of vacuum
S350N pumps described at p. 000 V205

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 551

SECTION S | SOIL

PRESSURE SYSTEM S342-01

2 WAYS PRESSURE PANEL NEW
S340
DIAL GAUGE UNITS 4 VALVES This pressure panel is designed to distribute the water pressure used
in soil laboratory applications, such as automatic triaxial systems.
TO MEASURE PRESSURE (0-1700 KPA) The panel is constituted by two pressure lines fitted with high
4 inlet/outlet null displacement valves are supplied with the dial accurate regulators and pressure valves.
gauge. Used to measure water pressure as cell pressure or pore
pressures. The dial gauge is set in a metallic support. Dimensions: 416x430x181 mm
Pressure range: 0-1700 kPa. Weight: 10 Kg approx. S342-05

Dimensions: 410x350x110 mm
Weight: 6 kg approx.

S342-01
S340
S345 S342-02
SCREW PUMP 3 WAYS PRESSURE PANEL NEW
It has to be connected to the pressure dial gauge unit and it is used Identical to the S342-02 but fitted with three pressure lines.
to control water pressures by means of small screw rotations. It can
decrease or decrease pressures as required. Dimensions: 460x430x181 mm
Weight: 13 Kg approx.
Weight: 3 kg approx. S342-05

S345

S348 S350-01
S342-02

S348 ACCESSORY
DISTRIBUTION UNIT
It is provided with 5 inlet/outlet valves with null variation of volume. S342-05 DIGITAL GAUGE to be fitted on S342-01 and S342-02.
All valves are connected to an aluminium support. It is used to Resolution: 1 kPa
deliver pressurized water to different lines.
Dimensions: 200x200x55 mm SPARES
Weight: 3 kg approx.
S342-04 Pressure air regulator, 10 bar
S350-01 Two-way distribution valve for air or water. S325 Nylon tube Ø 4x6 mm

Tel: +44 (0) 1442 402770

 E: [email protected]

552 RETURN TO HOMEPAGE

SECTION S | SOIL

PORE PRESSURE TRANSDUCER S356N

It is a good reliability electronic device used to measure pore 2 CHANNELS UNIT FOR PORE PRESSURE MEAS-
pressure. It requires a de-airing block. Every transducer must be UREMENT
connected to the automatic data acquisition system mod. S334 Based on a high resolution graphic display this instrument allows
(see p. 000) or mod. S301-05 ( see p. 000). continuous control and monitoring of pore pressure measurements
- Input voltage: 10 volts dc, Sensitivity range: 2 - 4 mV/V coming from pressure transducers.
- Accuracy: 0.15 fs Models like S336-50 or S336-51 supplied along with proper con-
- Pressure connection: 0.25 BSP nection cable can be plugged into this new S356N readout so that
- Protected against corrosive pore water pressure manual triaxial tests can be performed without need of automatic
- 2 metres cable and 5 pin plug included data acquisition units or outdated mercury manometers.
S356N unit allows real time visualization of the pore pressure
MODELS measurements and subsequent peak data recording through its
dedicated peak function.
S336-50 Pressure transducer up to 1000 kPa
S336-51 Pressure transducer up to 2000 kPa Technical specifications
- Measuring units (selectable): mbar, bar, MPa, kPa, psi
- Acquisition and data processing system at 24 bit, effective reso-
ACCESSORIES
lution: 17 bit.
S336-55 De-airing block for pressure transducer - Operator interface composed by 5 multi-functions pushbuttons;
function icons shown on the display
- The two analogue-digital channels accept sensors at 2mV/V
S336-51 - Languages: see C108N at page XXX
- Graphic display with high resolution: 192x64 pixels
S336-50 - Class: 0.5% starting from 10% of maximum value
Power supply: 230V 1ph 50-60Hz
Dimensions: 230x145x240 mm
Weight: 4 kg approx
S336-55
ACCESSORIES for S356N
EXTENSION CABLE FOR TRANSDUCERS
- Pressure transducers, available models see p. 000
MODELS - De-aired blocks, available models see p. 000
- Extension cables for transducers, see p. 000
S336-30 2 metres long
S336-31 5 metres long
S336-32 10 metres long

Note: It is recommended to use not more than 10m of

extension cable to avoid noise problems that
might occur.

Channel configuration and calibration S356N+S336-50+S336-51

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 553

SECTION S | SOIL

MEASURE OF VOLUME CHANGE ACCESSORIES for VOLUME GAUGES

In order to measure volume changes during test, two solutions are
proposed: S336-12 Displacement transducer 25 mm travel TYPE “A”
Double burette apparatus S336-16 Displacement transducer 25 mm travel TYPE “B”
Standard or automatic volume gauge with displacement
transducer or dial gauge. Note: Technical data for all transducers: see p. 000

S335-15 Universal coupling pliers to hold the transducer/dial

S358
gauge. It fits all Matest displacement transducers and
DOUBLE BURETTE VOLUME CHANGE APPARATUS dial gauges (from Ø 8 mm to 20 mm).
It is composed by two measuring burettes which are placed inside a
S338-05 Mounting device of the universal coupling pliers mod.
perspex tube and connected directly to a reverse valve system.
S335-15 to fix the displacement transducer/dial gauge
A by-pass valve is also included.
to the volume gauge.
Capacity: 200ml
Accuracy: 0.2ml
S359
Dimensions: 230x270x860 mm
Weight: 5 kg approx.
THREE-CELLS CONSOLIDATION FRAME
It is used to apply a constant axial load to three specimens, at the
S338N same time. It performs an anisotropic consolidation stage reducing
VOLUME GAUGE the consolidation testing times.
It is made of a resistant metallic structure which accepts up to 3
The unit consists of a metallic air/water
triaxial cells for specimens dia. 38 mm up to 100 mm, and it is
interface. It measures the water volume
provided with centering plate cells.
changes inside the sample. It has to be used
Load can be applied through an hanger with two different ratios:
with linear strain transducer, or dial gauge.
- Ratio 1:1 (directly), maximum load for each cell: 50 kg
Capacity: 100 ml
- Ratio 5:1 (by means of a lever), maximum load for each cell: 250 kg
Accuracy: better than 0.1 ml.
Dimensions: 2300x400x1800 mm
Dimensions: 180x180x240 mm
Weight: 150 kg approx.
Weight: 4.7 kg approx.
Easy de-airing of bottom and top chambers.
No measuring device and mounting block ACCESSORIES
are included (see accessories).
S273 KIT Set of slotted weights 50 kg

S338-01 KIT S377 Dial gauge, 25x0.01 mm suitable for specimens of

S358
max. dimensions 50x100 mm
AUTOMATIC VOLUME GAUGE
S379 Dial gauge, 50x0.01 mm suitable for specimens of
The unit consists of a 100 ml metallic max. dimensions 70x140 mm
air/water interface. A change valve box
As an alternative:
provides unlimited capacity.
Easy de-airing of top and bottom S336-12 Displacement transducer 25 mm travel
chambers. Displacement transducer, S336-14 Displacement transducer 50 mm travel
coupling pliers and mounting device
are not included (see accessories)
Capacity : unlimited
Accuracy: better than 0.1 ml
S338N
Dimensions:
360x270x210 mm
Weight:
7.6 kg approx.
S338N

Note:
The volume gauge has to be
used with linear strain transducer
which must be connected to the
automatic data acquisition system
mod. S334 (see p. 000) or mod. S359 with accessories
S301-05 ( see p. 000). S338-01 KIT

Tel: +44 (0) 1442 402770

 E: [email protected]

554 RETURN TO HOMEPAGE

SECTION S | SOIL

S335-10N
SOFTWARE TRIAXLAB CONNECT & REPORTS
STANDARDS: NF P94-070, P94-074 | ASTM D2850-03a, D4767-95, D7181-11 | BS 1377:8
TriaxLab Connect is the new acquisition software for Matest triaxial systems. This software allows the user to:
- Configure the acquisition parameters necessary to conduct the test
- Perform all of the 3 steps of a triaxial test (saturation, consolidation and shearing)
- Calculate the t100 value used for the shearing speed
- Record data for each calculation step
- Save test data and test parameters
Hence, the files created by this software can be used in TriaxLab Reports to generate a report by selecting the dedicated Standards.
Both Connect and Reports programs can be used in a very simple and intuitive way. Thanks to a suitable window, TriaxLab Reports gives the
opportunity to perform calculations for all triaxial tests (UU, CU+u or CD).

S335-10N Consolidation step in TriaxLab Connect

The software provides the user with a simple and flexible graphical interface, giving the possibility to view, edit and print all the parameters
involved in triaxial tests.
Laboratory coefficients of:
- Saturation
- Consolidation
- Shearing

CHARTS:
- Water Volume (cm3) / Square-root Time (min)
- Press Load (kN) / Press Displacement (mm)
- Deviator Stress (kPa) / Axial Strain (%)
- Pore Pressure (kPa) / Axial Strain (%)
- Shear Stress (kPa) / Normal Stress (kPa)
- Volume Deformation (%) / Axial Strain (%)
- Stress t’ (kPa) / Stress s’ (kPa)
- Effective Principal Stress Ratio / Axial Strain (%)

PC specification:
- Operating system: Windows XP or more recent
S335-10N Test CU+u results in TriaxLab Reports

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 555

SECTION S | SOIL

RECOMMENDED TYPICAL CONFIGURATION OF THE TRIAXIAL SYSTEM WITH ONE CELL IN

MANUAL, AUTOMATIC AND AUTOMATIC WITH SUBMERSIBLE LOAD CELL VERSIONS
APPARATUS SECTION

ITEM CODE

ITEM DESCRIPTION

ALTERNATIVE ITEM

MANUAL CELL SET

AUTOMATIC CELL SET

AUTOMATIC CELL SET

with Submersible Load Cell
Hardware S301N digital triaxial load frame 50 kN 1 1 1
Software S301-05 acquisition and data processing - 1 1
S305 triaxial cell dia max. 70 x 140 mm S306 1 1 1
S335-10N software triaxlab reports - Matest Made - 1(opt) 1(opt)
Measure of S370-05S load proving ring 10 kN S370/1-xxS 1 - -
Axial force S374 stem mechanical brake device 1(opt) - -
S337-32 electric load cell 10 kN capacity S377-31..34 - 1 -
S337-04 submersible load cell 10 kN S337-02..05 - - 1
S337-21 loading ram for submersible cell - - 1
S337-51 calibration process for load cell - 1(opt) 1(opt)
Measure of S377 dial gauge 25 mm S379 1 - -
Axial strain S336-12 displacement transducer 25 mm S336-16 - 1 1
S336-31 extension cable 5 m S336-30..32 - 1 1
S335-15 universal coupling pliers 1 1 1
S305-05 mounting device for pliers 1 1 1
S337-51 calibration process for displacement transducer - 1(opt) 1(opt)
S336-45 gauge block 25 mm S336-41..47 - 1(opt) 1(opt)
De-aired S355 de-airing tank 1 1 1
water system V205 vacuum pump 1 1 1
V205-10 vacuum regulator 1 1 1
V205-12 moisture filter 1 1 1
V230-03 rubber tube 3 m 1 1 1
Pore pressure S350N air/water interface pressure system A144 2 2 2
system and S351N laboratory air compressor 17 bar V207 1 1 1
measure (only if S350N system is chosen)
S350-04 membrane for air/water cell (spare) 1(opt) 1(opt) 1(opt)
(only if S350N system is chosen)
S350-05N pressure regulator 2 2 2
(only if S350N system is chosen)
S355-01 filter unit 1 1 1
S340 dial gauge unit 4 valves S342-01 + S342-05 2 2 2
(only if S350N system is chosen)
S345 screw pump (only if S340 is chosen) 2 2 2
S348 distribution unit - - -
S350-01 2-way distribution valve 5 5 5
S336-51 pore pressure transducer 2000 kPa S336-50 - 3 3
(cell pressure + pore + back pressure)
S336-55 de-airing block - 3 3
S336-31 extension cable 5 m S336-30..32 - 3 3
S356N digital pore pressure readout 1(opt) - -

Tel: +44 (0) 1442 402770

 E: [email protected]

556 RETURN TO HOMEPAGE

SECTION S | SOIL

Measure of S358 double burette system S338N 1 - -

Volume change S377 dial gauge 25 mm 1 - -
(only if S338N system is chosen)
S335-15 universal coupling pliers 1 - -
(only if S338N system is chosen)
S338-05 mounting device for pliers 1 - -
(only if S338N system is chosen)
S338-01 KIT automatic volume gauge S338N - 1 1
S336-12 diplacement transducer 25 mm S336-16 - 1 1
S336-31 extension cable 5 m S336-30..32 - 1 1
S335-15 universal coupling pliers - 1 1
S338-05 mounting device for pliers - 1 1
S337-51 calibration process for displacement transducer - 1(opt) 1(opt)
Specimen S310 rubber membrane (10 pcs) S310-01..03 1+ 1+ 1+
preparation (accordingly to specimen dimensions)
and Accessories S311 “O” ring (10 pcs) S311-01..03 1+ 1+ 1+
(accordingly to specimen dimensions)
S312 membrane stretcher S312-01..03 1 1 1
(accordingly to specimen dimensions)
S313 split former S313-01..03 1 1 1
(accordingly to specimen dimensions)
S313-10 split mould S313-11..13 1 1 1
(accordingly to specimen dimensions)
S314 top cap with drainage S314-01..03 1 1 1
(accordingly to specimen dimensions)
S315 base adapter for cell S315-01..07 1 1 1
(accordingly to cell model and specimen dimensions)
S316 porous disc (2 pcs) for CD/CU/UU tests S316-01..03 1 1 1
(accordingly to specimen dimensions)
S317 plain disc (2 pcs) for UU test only S317-01..03 1 1 1
(accordingly to specimen dimensions)
S318 “O” ring for base adapter S318-01..03 1+ 1+ 1+
(accordingly to specimen dimensions)
S319 filter paper for lateral drainage (50 pcs) S319-01..03 1+ 1+ 1+
(accordingly to specimen dimensions)
S320 filter paper for base (100 pcs) S320-01..03 1+ 1+ 1+
(accordingly to specimen dimensions)
S122-13 stainless core cutter S122-14..16 1 1 1
(accordingly to specimen dimensions)
S123-13 dolly for extraction S123-14..16 1 1 1
(accordingly to specimen dimensions)
S321 drainage burette 10 ml S322 1 1 1
S325 nylon tube Ø 6x4 (20 m) 3 3 3
S326 terminal for connection tube (10 pcs) 1+ 1+ 1+
S327 flaring tool 1 1 1
S328 vaseline oil (1 kg) 1+ 1+ 1+
S329 silicon grease (1 kg) 1+ 1+ 1+
S330 grease pump 1 1 1
S331 null displacement valve (spare) 1(opt) 1(opt) 1(opt)
S332-02 wearable material and recommended spares S332-02..05 1 1 1
(accordingly to cell set)

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 557

SECTION S | SOIL

RECOMMENDED TYPICAL CONFIGURATION OF THE TRIAXIAL SYSTEM WITH THREE CELL IN

MANUAL, AUTOMATIC AND AUTOMATIC WITH SUBMERSIBLE LOAD CELL VERSIONS
APPARATUS SECTION

ITEM CODE

ITEM DESCRIPTION

ALTERNATIVE ITEM

3 MANUAL CELL SET

3 AUTOMATIC CELL SET

3 AUTOMATIC CELL SET

with Submersible Load Cell
Hardware S301N digital triaxial load frame 50 kN 1 1 1
Software S301-05 acquisition and data processing - 1 1
S301-06 8 channel expansion module - 1 (opt) 1 (opt)
S305 triaxial cell dia max. 70 x 140 mm S306 3 3 3
S359 3 cell consolidation frame 1 1 1
S273 KIT set of slotted weights 50 kg 3 3 3
S335-10N software triaxlab reports - Matest Made - 1 (opt) 1 (opt)
Measure of S370-05S load proving ring 10 kN S370/1-xxS 1 - -
Axial force S374 stem mechanical brake device 1 (opt) - -
S337-32 electric load cell 10 kN capacity S377-31..34 - 1 -
S337-04 submersible load cell 10 kN S337-02..05 - - 1
S337-21 loading ram for submersible cell - - 1
S337-51 calibration process for load cell - 1 (opt) 1 (opt)
Measure of S377 dial gauge 25 mm S379 4 - -
Axial strain S336-12 displacement transducer 25 mm S336-16 - 4 4
S336-31 extension cable 5 m S336-30..32 - 4 4
S335-15 universal coupling pliers 4 4 4
S305-05 mounting device for pliers 4 4 4
S337-51 calibration process for displacement transducer - 4 (opt) 4 (opt)
S336-45 gauge block 25 mm S336-41..47 - 1 (opt) 1 (opt)
De-aired S355 de-airing tank 1 1 1
water system V205 vacuum pump 1 1 1
V205-10 vacuum regulator 1 1 1
V205-12 moisture filter 1 1 1
V230-03 rubber tube 3 m 1 1 1
Pore pressure S350N air/water interface pressure system A144 6 6 6
system and S351N laboratory air compressor 17 bar V207 1 1 1
measure (only if S350N system is chosen)
S350-04 membrane for air/water cell (spare) 1 (opt) 1 (opt) 1 (opt)
(only if S350N system is chosen)
S350-05N pressure regulator 6 6 6
(only if S350N system is chosen)
S355-01 filter unit 1 1 1
S340 dial gauge unit 4 valves S342-02 + S342-05 3 3 3
(only if S350N system is chosen)
S345 screw pump (only if S340 is chosen) 3 3 3
S348 distribution unit 3 3 3
S350-01 2-way distribution valve 6 6 6
S336-51 pore pressure transducer 2000 kPa S336-50 - 9 9
(cell pressure + pore + back pressure)
S336-55 de-airing block - 9 9
S336-31 extension cable 5 m S336-30..32 - 9 9

Tel: +44 (0) 1442 402770

 E: [email protected]

558 RETURN TO HOMEPAGE

SECTION S | SOIL

S356N digital pore pressure readout 2 (opt) - -

Measure of S358 double burette system S338N 3 - -
Volume change S377 dial gauge 25 mm 3 - -
(only if S338N system is chosen)
S335-15 universal coupling pliers 3 - -
(only if S338N system is chosen)
S338-05 mounting device for pliers 3 - -
(only if S338N system is chosen)
S338-01 KIT automatic volume gauge S338N - 3 3
S336-12 diplacement transducer 25 mm S336-16 - 3 3
S336-31 extension cable 5 m S336-30..32 - 3 3
S335-15 universal coupling pliers - 3 3
S338-05 mounting device for pliers - 3 3
S337-51 calibration process for displacement transducer - 3 (opt) 3 (opt)
Specimen S310 rubber membrane (10 pcs) S310-01..03 1+ 1+ 1+
preparation (accordingly to specimen dimensions)
and Accessories S311 “O” ring (10 pcs) S311-01..03 1+ 1+ 1+
(accordingly to specimen dimensions)
S312 membrane stretcher S312-01..03 1 1 1
(accordingly to specimen dimensions)
S313 split former S313-01..03 1 1 1
(accordingly to specimen dimensions)
S313-10 split mould S313-11..13 1 1 1
(accordingly to specimen dimensions)
S314 top cap with drainage S314-01..03 3 3 3
(accordingly to specimen dimensions)
S315 base adapter for cell S315-01..07 3 3 3
(accordingly to cell model and specimen dimensions)
S316 porous disc (2 pcs) for CD/CU/UU tests S316-01..03 3 3 3
(accordingly to specimen dimensions)
S317 plain disc (2 pcs) for UU test only S317-01..03 1 1 1
(accordingly to specimen dimensions)
S318 “O” ring for base adapter S318-01..03 1+ 1+ 1+
(accordingly to specimen dimensions)
S319 filter paper for lateral drainage (50 pcs) S319-01..03 1+ 1+ 1+
(accordingly to specimen dimensions)
S320 filter paper for base (100 pcs) S320-01..03 1+ 1+ 1+
(accordingly to specimen dimensions)
S122-13 stainless core cutter S122-14..16 1 1 1
(accordingly to specimen dimensions)
S123-13 dolly for extraction S123-14..16 1 1 1
(accordingly to specimen dimensions)
S321 drainage burette 10 ml S322 1 1 1
S325 nylon tube Ø 6x4 (20 m) 9 9 9
S326 terminal for connection tube (10 pcs) 2+ 2+ 2+
S327 flaring tool 1 1 1
S328 vaseline oil (1 kg) 1+ 1+ 1+
S329 silicon grease (1 kg) 1+ 1+ 1+
S330 grease pump 1 1 1
S331 null displacement valve (spare) 1 (opt) 1 (opt) 1 (opt)
S332-02 wearable material and recommended spares S332-02..05 1 1 1
(accordingly to cell set)

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 559

SECTION S | SOIL

AUTOMATIC DATA ACQUISITION AND PROCESSING SYSTEM FOR GEOTECHNICAL TESTS

S334
DATATRONIC 8 CHANNELS CYBER-PLUS EVOLUTION TOUCH SCREEN
EXPANDABLE TO 16 CHANNELS

Controller for MATEST equipment or

for other manufacturers machines

S334

S276 Direct/Residual shear tests

S260 Consolidation test

S301N Triaxial UU - CU - CD tests

S290 Consolidation frame for shear boxes and consolidation cells S359 Consolidation frame for triaxial specimens

Tel: +44 (0) 1442 402770

 E: [email protected]

560 RETURN TO HOMEPAGE

SECTION S | SOIL

S334
DATATRONIC 8 CHANNELS CYBER-PLUS EVOLUTION TOUCH SCREEN
EXPANDABLE TO 16 CHANNELS
This unit is designed and produced to satisfy the requirements of all laboratories, from the small, up to the most complex.
8 channels acquisition and processing data system (expandable to 16 channels, see accessory mod. S334-01), colour “Touch Screen” display,
it automatically performs test and data processing. Directly connected to PC via USB, it prints the test certificate. Equipped with slots for external
Pendrive or SD Card infinite memory supports. Hardware technical details at p. 00.
One or more cyber-plus (8 or 16 ch) can be connected to create a network multichannel system. A flexible, customizable and infinitely expanda-
ble solution.
Data collection is completely automatic, improving considerably the productivity and cost effectiveness.
Windows based program with menu driven command selection, is straightforward and easy to follow and does not require a skilled operator.

The system can be used for:

ACCESSORIES
- Oedometer (consolidation ) tests
- Direct and residual shear tests (cycle test) S334-01 8-CHANNEL INTERNAL MODULE, for system expansion
- Triaxial UU, CU, CD tests to 16 channels.
- Automatic data acquisition and processing systems permit the uti-
lization of different channels that can be independently calibrated, S334-11 NETWORK CONNECTION RJ45 cable.
zeroed and set up in order to visualize the units being measured; S334-12 SWITCH to connect from 2 up to 7 Cyber-Plus
- The appliances contain a modern high speed - high performing (mod. S334) to the Ethernet network.
24 bit conversion device;
- The appliances permit to acquire the signals coming from differ-
ent types of transducers: S334-12
- Strain Gauge Bridge and Potentiometric Wide input range availa-
ble for the electrical signal:
± 40 mV ... ± 3 V
- User interface:
Full-color display 320×340 pixel – Touchscreen
- Data storage:
The data test can be stored directly into the appliance on a flash
memory and be transferred to the PC at the end of the test by S334-11
USB pendrive or SD card
- Every channel can be set with different sampling modes (linear
form, quadratic form, logarithmic form, etc.). The sampling
process can be executed with different frequencies: from 50 ms
to infinite
- The calibration data are protected by password and
they can be transferred to external supports archives.
Power supply: 230V 1ph 50Hz
Dimensions: 260x260x155 mm
Weight: 5 kg approx.

System expansion to 16 channels. S334-01

S334 output channels and readings

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 561

SECTION S | SOIL

TRIAXLAB AUTOMATED SYSTEM

STANDARDS: BS 1377:7, BS 1377:8 | ASTM D2850, D4767, D7181 | NF P94-070, P94-074 | CEN-ISO-TS 17892
NEW

MAIN FEATURES

Automatic execution of 6 independent triaxial

tests from start to finish.
Type of tests: total and effective stress, stress path,
optional K0 and permeability.
Servo feedback controlled precision pressure
(Pressurematic) generation system.
Real time graphing and configurable real time
transducers.
Pre-programmed user-friendly “Method files”
through the TestLab Software.
Compact and versatile for improving productivity and
cost effectiveness.
No need of air source.

TriaxLab Automated System

Matest TRIAXLAB is an outstanding system specifically designed for Based on the unparalleled performance of CDAS and flexibility of
advanced soil testing. TestLab Software, the new MATEST TriaxLab Automated System
This system can be used from educational to construction engineering is the optimized system to perform fully automatically total and
laboratories to reduce to the absolute minimum any form of manual effective triaxial tests such as:
intervention. CD Consolidated Drained test
CU Consolidated Undrained test
UU Unconsolidated Undrained test
Stress path
Optional K0 tests
Optional Permeability tests

Tel: +44 (0) 1442 402770

 E: [email protected]

562 RETURN TO HOMEPAGE

SECTION S | SOIL

The TRIAXLAB automated system basically consists of 3 major

groups: MAIN FEATURES

Load frame and triaxial cell with accessories POWERFUL

Equipped with Pavetest’s leading edge Control
Control system based on the CDAS Control and Data Acquisition and Data Acquisition System (CDAS) and TestLab
System and TestLab Software controlled by PC Software.
VERSATILE
Data Acquisition System comprising: Designed for routine tests, central laboratories and
- 1 load cell for axial force for research purposes.
- 1 displacement transducer for axial displacement
GREAT EFFICIENCY
- 2 pressure transducers for cell pressure and back pressure By working in complete automatic mode, it reduces
- 1 pressure transducer for pore pressure to absolute minimum the manual intervention.
- 2 Pressurematic for pressure / volume change EASY TO USE
The system works via the pre-programmed Method
Files.
To suit the specific customer’s requirements the MATEST TriaxLab
FLEXIBLE
Automated System basic configuration can be modified by adding
Multiple triaxial tests with no need for compressed
or removing the hardware elements which are controlled and
air supply.
monitored under a closed-loop integrated system with the CDAS
and TestLab Software.
Pre-programmed “Method files” offer the operator the unique
opportunity to run a range of tests without the need for specific
computer programming. The possibility to customize the Method
files is also given to the operator granting ultimate flexibility and
versatility.

S355 S305-05
S336-23
S335-15

S337-43

S342-03

S305

S336-53

S349-10

H009-01N

S303

S349
S301-01

Triaxlab – Advanced Technology for effective Triaxial Tests

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 563

SECTION S | SOIL

TRIAXLAB AUTOMATED SYSTEM

ORDERING INFO:
HARDWARE - SOFTWARE MEASURE OF AXIAL FORCE DEAIRED WATER SYSTEM
S301-01 S337-43 S355
DIGITAL TRIAXIAL LOAD FRAME 50 KN LOAD CELL 25 KN WITH SIGNAL DE-AIRING TANK 20 LITRES CAPACITY
Technical Specifications: CONDITIONER It produces de-aired water when connected
Maximum load capacity: 50 kN Rated output: 2 mV/V nominal to the vacuum pump. It is a perspex tank with
Infinitesimal testing speed: Accuracy: 0.1% an inlet water valve and an outlet air valve.
from 0.00001 to 12 mm/min Tank capacity: 20 litres.
Dimensions: 320x320x520 mm
Minimum vertical clearance: 400 mm
MEASURE OF AXIAL STRAIN Weight: 15 kg approx.
Maximum vertical clearance: 1100 mm
Horizontal clearance: 380 mm S336-23
TRANSDUCER TYPE “A” TRAVEL 25 MM
Platen diameter: 177 mm
WITH SIGNAL CONDITIONER
Power Supply: 230V 1ph 50/60Hz 600W
Independent linearity: <0.3% (0.3 x 10 mm)
S303 Max. displacement speed: up to 10 m/S
CDAS AND TESTLAB SOFTWARE
S355
Technical Specifications: Note: For different requirements load
Acquisition 16 Channels 20 bit resolution cells capacity and transducers stroke or ACCESSORIES
Sampling rate up to 192 kHz submersible load cells, see page 000
(all channels) V205 V205-10
Smoothing up to 64 times over-sampling VACUUM PUMP
To produce vacuum
Calibration Automatically on power up
up to of 0,1 mbar V205
Control Axis 4 ACCESSORIES (see p. 000)
Communication USB or Ethernet
S305-05 V205-10 - V205-12
Power supply: Mounting device of the universal coupling VACUUM REGULATOR
90-264 V 50/60 Hz 1 ph 240 W pliers mod. S335-15 to fix the displacement It is supplied with vacuum gauge, control
Dimensions: 100(h) x 310(d) x 250(w) mm transducer/dial gauge to the Triaxial Cell. valve, suction filter and moisture trap.
S305 S335-15
V230-03
TRIAXIAL CELL MAX. Ø 70X140 MM Universal coupling pliers to hold the
Rubber tube. Suitable for vacuum, 3 m
transducer/dial gauge. It fits all Matest
Technical Specifications:
displacement transducers and dial gauges
Max. specimen size: mm Ø 70x140
(from dia. 8mm to 20mm).
Max. cell pressure: 1700 kPa MEASURE OF PORE PRESSURE
S337-51
Overall dimensions: mm Ø 280x480 SYSTEM AND VOLUME CHANGE
Calibration process of one force, strain and
Weight: 8 kg approx. pressure device that is combined with the S349
CDAS control and data acquisition system. PRESSUREMATIC PVC FOR AUTOMATIC
S306 PRESSURE AND VOLUME CONTROL
TRIAXIAL CELL MAX. Ø 100X200 MM
Technical Specifications:
Technical Specifications: S336-23 Output pressure: 3500 kPa
S335-15
Max. specimen size: mm Ø 100x200
Volume capacity: 250 cc
Max. cell pressure: 1700 kPa
Overall dimensions: mm Ø 310x540
NEEDED ACCESSORIES
Weight: 16 kg approx.
S305-05 S336-53 Pressure transducer 2000 kPa
S307
with signal conditioner.
TRIAXIAL CELL MAX. Ø 150X300 MM
S336-55 De-airing block for pressure
Technical Specifications:
transducer
Max. specimen size: mm Ø 150x300
S349-10 Solenoid valve
Max. cell pressure: 2200 kPa
Overall dimensions: mm Ø 338x648
OPTIONAL ACCESSORIES
Weight: 40 kg approx. S305 S306
See p. 000 with accessories S342-03 3 ways water distribution panel

Tel: +44 (0) 1442 402770

 E: [email protected]

564 RETURN TO HOMEPAGE

SECTION S | SOIL

S303
CDAS – CONTROL AND DATA ACQUSITION SYSTEM NEW

MAIN FEATURES

Directly communicates with the TestLab software,

providing automatic test execution and data
processing.
Compact high reliability data acquisition and control.
Up to 5 kHz data acquisition and feedback control
provides excellent waveform fidelity.
Normalized (±10V ) analog data acquisition inputs
provide flexibility to use any transducer in any
channel.
Software and test methods expandable for future
S303 CDAS 16 Channels
requirements.

Pavetest’s compact Control and Data Acquisition System (CDAS)

THECNICAL SPECIFICATIONS
delivers unparalleled performance, real time control and ultimate
versatility in acquisition and provide a flexible and user friendly testing S303
solution for soils when coupled with the Matest TriaxLab Automated 16 Channel CDAS
System and the Cyclic TriaxLab Automated one. Acquisition 16 CH, 20 bit resolution
Sampling rate up to 192 kHz (all channels)
The CDAS provides excellent waveform fidelity from integrated
acquisition and control functions, with low level sampling at speeds Smoothing up to 64 times over-sampling for low noise
of up to 192,000 samples per second simultaneously on all channels performance
(using up to 64x oversampling). Calibration automatically on power up
Control Axis 4
S303 CDAS provides an optimized solution for the TriaxLab Communication USB or Ethernet
Automated Systems. The CDAS works with close synchronization to
the TestLab software providing dynamic and precise servo control of
the TriaxLab frame, Pressurematic systems. Acquisition and control
is provided for:
Vertical load and displacement
Power supply: 90-264V 50-60Hz 1pPh 240W
Confining and back pressure (through the solenoid valve) Dimensions: 100 (h) x 310 (d) x 250 (w) mm
Volume change and water pressures Weight: 2 kg approx.
Local strain

TriaxLab conceptual
schematic

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 565

SECTION S | SOIL

S349
PRESSUREMATIC PVC NEW
Pressurematic is the new solution for geotechnical laboratories
MAIN FEATURES demanding automatic pressure and volume control. By using a
servo stepper motor directly controlled by the TestLab software and
Compact stainless steel construction CDAS, Pressurematic allows to build confining pressure and back
Powered and controlled by the CDAS and TestLab pressure up to 3500 kPa. The unparalleled performance of the
Software CDAS allows to regulate the pressure under a closed loop control
regulated to 0.1 kPa.
Closed loop control up to 3500 kPa The operation is continuously monitored by the TestLab software,
0.001 kPa pressure and 0.0003 cc volume resolution thus catering to all levels of operator experience.

High volume capacity: 250 cc Standard effective stress tests require 2 Pressurematic units: one
Graduated scale for approximate volume change for cell pressure and the other for back pressure which can be also
indication used to measure the change in volume of the specimen to 0.0003
cc. The latter is provided with a solenoid valve directly installed
No need of air source on the triaxial cell and used to open and close the pressure line
whenever it is needed.

S349

THECNICAL SPECIFICATIONS NEEDED ACCESSORIES

Output pressure: 3500 kPa S336-53 Pressure transducer up to 2000 kPa

Volume capacity: 250 cc S336-55 De-airing block for pressure transducer
Pressure accuracy: 0.25% of full scale S349-10 Solenoid valve
Pressure resolution: 0.001 kPa
Volume resolution: 0.0003 cc OPTIONAL ACCESSORIES
Closed loop control of pressure regulated to 0.1 kPa
S342-03 3 ways water distribution panel
Closed loop control of volume regulated to 0.0003 cc
Maximum operational speed: 8 cc/s

Power supply: 24V DC 1A powered from CDAS

Dimensions: 900x110x230 mm
Weight: 7 Kg approx.

S342-03

Tel: +44 (0) 1442 402770

 E: [email protected]

566 RETURN TO HOMEPAGE

SECTION S | SOIL

TRIAXLAB AUTOMATED SYSTEM: suggested typical configuration

Apparatus Section Item Code Item Description Quantity
Hardware Software S301-01 Triaxial load frame 50kn for triaxlab automated system 1
S303 16 ch CDAS & testlab software 1
S305 Triaxial cell max ø 70x140 mm 1
Measure of Axial force S337-43 Load cell 25 kn capacity with signal conditioner 1
S337-51 Calibration process for load cell 1
Measure of Axial Strain S336-23 Transducer type “a” travel: 25 mm with signal conditioner 1
S337-51 Calibration process for displacement transducer 1
S305-05 Mounting device on triaxial cell 1
S335-15 Universal coupling pliers for transducer 1
De-aired water system S355 De-airing tank 1
S355-01 Filter group (water trap) 1
V205 Vacuum pump 1
V205-10 Vacuum regulator 1
V205-12 Condensed water trap 1
V230-03 Rubber tubing for vacuum, 3 metres 1
Measure of pore pressure S349 Pressurematic PCV 2
and volume change S336-53 Pressure transducer 2000 kpa with signal conditioner 3
S337-51 Calibration process for pressure transducers 3
S336-55 De-airing block 3
S342-03 3 ways water distribution pannel 1
S349-10 Solenoid valve 1
Specimen preparation and S310-01 Rubber membrane ø 50 mm (10 pcs) 2
Accessories S311-01 Sealing ring ø 50 mm (10 pcs) 1
(also available with Ø 38, 70, 100 mm)
S312-01 Membrane stretcher ø 50 mm 1
S313-01 Split former ø 50 mm 1
S313-11 Split mould ø 50 mm 1
S314-01 Top cap with drain ø 50 mm 1
S315-01 Plinth ø 50 mm for cell mod. s305 1
S316-01 Porous disc ø 50 mm (2 pcs) 1
S317-01 Plein disc ø 50 mm (2 pcs) 1
S318-01 “O” ring for plinth ø 50 mm 1
S319-01 Filter paper drain ø 50 mm (50 pcs) 1
S320-01 Filter paper for base ø 50 mm (100 pcs) 1
S122-14 Hollow punch ø 50 mm - triaxial 1
S123-14 Tamper ø 50 mm - triaxial 1
V205-11 Special oil for pumps 1
S325 Nylon tube ø 4 mm (20 mt) 2
S326 Terminal for connection tube (10 pcs) 2
S327 Flaring tool 1
S329 Water-repellent grease (1000 g) 1
S330 Grease pump 1
S328 Vaseline oil 1000 ml 1
S332-04 Spares and wearable 1 cell automatic 1+

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 567

SECTION S | SOIL

CYCLIC TRIAXLAB AUTOMATED SYSTEM

STANDARDS: ASTM D7181 | ASTM D2850 | ASTM D3999 | ASTM D4767 | ASTM D5311 | BS 1377:7 | BS 1377:8 | AASHTO T307

NEW MAIN FEATURES

Automatic execution of static and dynamic triaxial

tests including effective stress and stress path.
4 axis control and 16 channel control Data
Acquisition System.
Servo feedback controlled precision pressure
(Pressurematic) generation system.
Digital Servo-Pneumatic Control to provide accurate
loading wave shapes up to 70 Hz.
Real time charting.
Compact and versatile for improving productivity and
cost effectiveness.
Pre-programmed user friendly “Method files”
through the TestLab Software.
Possibility to upload user-defined wave-shapes (e.g.
earthquakes time series) through Replay Editor.
Fully configurable to suit a large range of testing
applications including maximum shear modulus
calculation through bender elements option.
Programmable Dashboard display showing real-time
system status and test result.

DTS-9 Cyclic TriaxLab Automated System

Matest Cyclic TriaxLab automated with its innovative features rep- Based on the 4 axis control and 16 channel control and Data
resents the most ideal solution for modern laboratories that need to Acquisition CDAS, Matest Cyclic TriaxLab has provision for:
investigate the effects of vibration and dynamic loading for soil and
Vertical load tension/compression up to 9 kN
unbound granular materials.
Typical applications include: Vertical displacement up to 50 mm
Civil engineering including seismic and blasting analysis Cell pressure up to 2000 KPa
Environmental engineering Back pressure up to 2000 KPa
Construction and architectural design
Advanced research on soils

Tel: +44 (0) 1442 402770

 E: [email protected]

568 RETURN TO HOMEPAGE

SECTION S | SOIL

The Cyclic TriaxLab automated system is subdivided into 3 major To suit the specific customer’s requirements the MATEST Cyclic
groups similarly to the TriaxLab Automated System: TriaxLab Automated System basic configuration can be modified by
Fully digital controlled load frame and fit for purpose Triaxial adding or removing the hardware elements which are controlled and
cell with accessories monitored under a closed-loop integrated system with the CDAS
Control system based on the CDAS and TestLab Software.
Data Acquisition System comprising: Pre-programmed “Method files” offer the operator the unique
- 1 submersible load cell for axial force opportunity to run a range of tests without the need for specific
- 3 pressure transducers for cell pressure, back pressure and computer programming. The possibility to customize the Method
pore pressure files is also given to the operator granting ultimate flexibility and
- 2 Pressurematic for pressure/volume change versatility.

Servo-valve Load frame & actuator

High performance, pneumatic Fully digital control of a high performance
servo-valve pneumatic servo-valve to provide accurate
loading wave shapes up to 70 Hz.

Triaxial cell
Top quality acrylic chamber with 5 in-
let valves to guarantee fully test de-
velopment according to international
standards.

S342-03

S307-11

S355

S307 S337-06 + S337-23 H009-01

S336-53

S336-55

B220-03 KIT
S349

CDAS TestLab software

The Compact Control and Data TestLab software allows for real time
Acquisition System (CDSA) delivers graphing of results and configurable Pressurematic
unparalleled performance, real real time transducer levels display The units are used for cell and back pressure
time control and ultimate versatility with unprecedented clarity of results control up to 2000 KPa. Automatic volume
in acquisition. and analytical power. changes to 0.001 cc is also provided.

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 569

SECTION S | SOIL

CYCLIC TRIAXLAB AUTOMATED SYSTEM ORDERING INFO:

HARDWARE - SOFTWARE MEASURE OF AXIAL FORCE DEAIRED WATER SYSTEM
B220-03 KIT S337-06 S355
DTS9 WITH MANUAL CROSSHEAD SUBMERSIBLE LOAD CELL 10 KN WITH DE-AIRING TANK 20 LITRES CAPACITY
The machine includes: SIGNAL CONDITIONER It produces de-aired water when connected
B220-13 Rated output 2 mV/V nominal to the vacuum pump. It is a Perspex tank with
20 kN load frame with manual crosshead Accuracy 0.1% an inlet water valve and an outlet air valve.
9 kN servo-pneumatic actuator with its LVDT, Tank capacity: 20 litres.
50mm stroke, 70 Hz frequency. Note: For different requirements load Dimensions: 320x320x520 mm
Power supply: 90-264V 50-60Hz 1ph 240W cells capacity and transducers stroke or Weight: 15 kg approx.
Dimensions: 1262(h)x400(d)x470(w) submersible load cells, see p. 000
Weight: 80 kg load frame
ACCESSORIES
S303
16 Channel Control and Data Acquisition ACCESSORIES FOR TRIAXIAL CELL V205
System (CDAS) and TestLab software. VACUUM PUMP
S337-23 Loading ram for the submersible To produce vacuum up to of 0.1 mbar
For technical specifications, see p. 000
load cell (see p. 000)
B270-12 S307-10 Vacuum generator
Air reservoir assembly with membrane dryer. V205-10 - V205-12
S307-19 Vacuum adaptor
It requires pressurized air, minimum 7 bar VACUUM REGULATOR
(not included). S307-11 Alignment coupler assembly It is supplied with vacuum gauge, control
S307-12 Spherical exclusion valve, suction filter and moisture trap.
S307
TRIAXIAL CELL MAX Ø 150X300 MM S307-13 Base pedestal spacer
V230-03
Technical specifications: Rubber tube. Suitable for vacuum, 3 m
OPTIONAL ACCESSORIES
Max specimen mm Ø 150x300
Max cell pressure 2200 kPa BENDER ELEMENTS KIT for the evaluation of MEASURE OF PORE PRESSURE
Overall dimensions mm Ø 338x648 the stiffness of a soil starting from the meas- SYSTEM AND VOLUME CHANGE
urement of the maximum shear modulus
Weight 40 kg approx. S349
(Gmax). The Kit includes:
S308 PRESSUREMATIC PVC FOR AUTOMATIC
S307-08 Picoscope
TRIAXIAL CELL MAX Ø 100X200 MM PRESSURE AND VOLUME CONTROL
S307-07 T-4001 waveforms transformer
Identical to S306 but with provision for cyclic Output pressure: 3500 kPa
S307-01 Universal puck for bender
triaxial testing. Volume capacity: 250 cc
elements top
For Technical Specifications, see p. 000
S307-02 Universal puck for bender
elements bottom NEEDED ACCESSORIES
S307-32 Base pedestal for bender element
50mm diameter S336-53 Pressure transducer 2000 kPa
S307-33 Top platen for bender element with signal conditioner.
50mm diameter S336-55 De-airing block for pressure
transducer
S307-34 Pair of porous disc
S349-10 Solenoid valve
Note: Bender elements are also available
in other diameters. OPTIONAL ACCESSORIES

S342-03 3 ways water distribution panel

S307 with accessories Bender elements KIT

Tel: +44 (0) 1442 402770

 E: [email protected]

570 RETURN TO HOMEPAGE

SECTION S | SOIL

TESTLAB SOFTWARE NEW

Developed with ultimate flexibility in mind, TestLab test and control software caters to all levels of operator experience. By using pre-programmed
Method files, an inexperienced operator can run a range of international test methods without the need for any programming.
Moreover, a test Wizard, available with popular tests, can guide the operator step by step based on a “recipe book” approach.
Most importantly, the experienced engineer and/or researcher need not be constrained by the functions and analysis in the method files provided.
The operator may clone, modify and/or generate his/her own method file to suit their specific requirements. The Excel based data analysis offers
the operator the flexibility to implement alternative analysis and customize reporting facilities.
TestLab allows for real time graphing of results and configurable real time transducer levels display with unprecedented clarity of results and
analytical power. These features make the TestLab software the optimized solution for the new Matest Triaxlab Automated and Cyclic Systems.

MAIN FEATURES

Pre-programmed Method files based on

international test methods for complete control
of triaxial testing for saturation, consolidation and
shearing phases.
Integrated data results post processing feature with
MS Excel.
Standard and user customizable test reporting.
Real time graphing of results and configurable real
time transducer.
Flexible and user-friendly with unprecedented clarity
of results and analytical power.
Automatic B value measurement.
Automatic backpressure solenoid valve control.

TESTLAB, A NEW APPROACH

TestLab is an open architecture user programmable software application. Our engineers have taken the time to review all the relevant international
test standards and used TestLab “Test Designer” to program method files according to these standards. Basically, any of these tests can be
designed, cloned and/or modified by the user within TestLab. The user is no longer restricted to the test applications provided at time of purchase
the possibilities are only limited by the skill and imagination of the user.

TESTLAB MANAGER TEST METHOD SELECTION

The TestLab materials testing software is designed to interface with The operator can run pre-programmed Method files, in accordance
the CDAS and a wide range of Pavetest machines including Auto- to the requested Standards, or configure an application test and then
matic TriaxLab system. A TestLab Manager interface allows users to save that configuration to a customised Method file. This includes
easily and efficiently locate the necessary method files to load and the real-time transducer and calibration allocations, comprising all
execute. the stresses, strain and volume changes for automatic triaxial test-
The method files for soil testing include: saturation, consolidation, ing; control parameters for the Pressurematic; solenoid valves and
CU compression test, CD compression test, UU compression test in triaxial frames; terminal conditions as for instance end of stroke or
accordance with: maximum capacity limits, test pause features for the Pressurematic
- ASTM 04767, ASTM D7181, BS 1377: part 8 live control, additional options to hold the stress and strain applied
- ASTM D2850, BS 1377: part 7 to the specimen.

TestLab Manager Selection of Method Files

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 571

SECTION S | SOIL

CYCLIC TRIAXLAB AUTOMATED SYSTEM: suggested typical configuration

Apparatus Section Item Code Item Description Quantity
Loading frame 1
Stretcher, actuator and B220-03-KIT Triple axis control & data acquisition system (CDAS) 1
controller 9 KN Servo-Pneumatic actuator assembly, 50 mm stroke,
1
LVDT ± 50 mm calibrated over ± 37.5 mm
S307 Triaxial cell for specimens up to 150x300 mm 1
S337-06 Submersible load cell calibrated to -5/+5 kn 1
S337-23 Loading ram for the submersible load cell (for S307) 1
S307-10 Vacuum generator 1
Trixial cells with
S307-19 Vacuum adaptor 1
accessories
S307-11 Alignment coupler assembly 1
S307-12 Spherical extension 1
S307-13 Base pedestal spacer 1
S337-51 Calibration process for load cell 1
S342-03 3 Ways distribution panel w/out regulators 1
S349 Pressurematic PVC 2
S349-10 Solenoid valve 1
S336-53 Pressure transducer 2000 kpa with ILC 3
Water pressure system, S336-55 De-airing block 3
measure of pressure and S355 De-airing tank 1
measure of volume S355-01 Filter group (water trap) 1
V205 Vacuum pump 1 stage air: 4.5 m³/h 1
S337-51 Calibration process for pressure transducers 3
V205-10 Vacuum regulator 1
V205-12 Condensed water trap 1
V230-03 Rubber tubing for vacuum, 3 meters 1
S307-30 Vacuum plate 50 mm specimen 1
S307-31 Vacuum top platen 50 mm specimen 1
S310-01 Rubber membrane ø 50 mm (10 pcs) 1
S311-01 Sealing ring ø 50 mm (10 pcs) 1
S312-01 Membrane stretcher ø 50 mm 1
S313-01 Split former ø 50 mm 1
Accessories for specimen S313-11 Two -part split mould ø 50 mm 1
preparation, Ø 50 mm S315-11 Plinth ø 50 mm for cell mod. s307 1
S316-01 Porous disc ø 50 mm (2 pcs) 1
S317-01 Plein disc ø 50 mm (2 pcs) 1
S318-01 "O" Ring tool for plinth ø 50 mm 1
S319-01 Filter paper drain ø 50 mm (50 pcs) 1
S320-01 Filter paper for base ø 50 mm (100 pcs) 1
S122-14 Hollow punchø 50 mm - triaxial 1
S123-14 Tamper ø 50 mm - triaxial 1
S307-60 Vacuum plate 150 mm specimen 1
S307-61 Vacuum top platen 150 mm specimen 1
S310-04 Rubber membrane ø 150 mm (10 pcs) 1
S311-04 Sealing ring ø 150 mm (10 pcs) 1
S312-05 Membrane stretcher ø 150 mm 1
Accessories for specimen
S313-04 Split former ø 150 mm 1
preparation, Ø 150 mm
S315-14 Plinth ø 150 mm for cell mod. s307 1
S316-04 Porous disc ø 150 mm (2 pcs) 1
S317-04 Plein disc ø 150 mm (2 pcs) 1
S318-04 "O" Ring tool for plinth ø 150 mm 1
S319-04 Filter paper drain ø 150 mm (50 pcs) 1
S320-04 Filter paper for base ø 150 mm (100 pcs) 1
S325 Nylon tube 4 mm ø (20 mt) 1
S326 Terminal for connection tube (10 pcs) 1
S327 Flaring tool 1
Other elements S328 Vaseline oil, 1000 ml 1
S329 Water-repellent grease (1000 g) 1
S330 Grease pump 1
S332-04 Spares and wearable 1 cell automatic 1

Tel: +44 (0) 1442 402770

 E: [email protected]

572 RETURN TO HOMEPAGE

SECTION S | SOIL

TESTLAB, USER FRIENDLY INTERFACE FOR SOIL TESTING NEW

TEST WIZARD REAL TIME DASHBOARD DISPLAY

The wizard section provides a prompted menu approach to running For the automatic and cyclic triaxial tests, Pavetest provides the
a test. The user is driven to enter information throughout a series user with an alternative, simpler and more intuitive representation
of easy steps. Examples of input information for consolidated of the current status of both machine and test method. This dash-
drained compression test include: board display feature of TestLab shows real time transducer levels,
- Specimen Information: axial gauge length (mm), Consolidated computed data and charted data before, during and after the test
Height (mm), Consolidated Area (mm²), Membrane Modulus has completed.
(MPa), Membrane thickness (mm), Filter Paper Kfp (kN/mm),
Filter Paper Perimeter Pfp (mm), Axial Strain Limit (%), Break
Detect (% drop)
- Loading sequences settings: confining pressure (kPa), Road
Seal Diameter (mm), back pressure valve, Loading rate (%/min)
- Test data: Axial Load (kN), Axial Deformation (mm), Total and
Effective Stress (kPa), Back and Pore Pressure (kPa), Volume
Change (cc) and Axial Strain (%)
- Real time tuning (PID control increments) and chart controls
(Corrected Deviator Stress, Axial Stress, Radial Stress, Induced
Pore Pressure, Effective Radial Stress)
Typical dashboard screen

POST PROCESSING
All TestLab Method file tests provide the facility to send the data
directly to an Excel workbook including test input and results data.
This facility provides a means of efficiently post processing raw
data results and customizing reports from within Excel and option-
ally displaying summary result in TestLab.

User guided Test wizard

TESTLAB UNIVERSAL TEST

The Test Data section displays run-time information, such as the
loading time, cycle count, transducer readings (force, displace-
ment, pressure), stress calculations.
Volume changes, B valve, consolidation parameters (t100), stress
path, optional K0 and permeability coefficients.
Post processing summary results

ASTM D4767, D7181-11 Automatic Saturation Excel post processing report

Tel: +44 (0) 1442 402770

 E: [email protected]

RETURN TO HOMEPAGE 573

SECTION S | SOIL

LOAD PROVING RINGS

Used for load compression measurement applied by the testing machine.
Made from hardened alloy steel, they are chrome-coated and complete with upper and lower coupling blocks having M10 female gas thread.
The accuracy is ± 1% of applied load and repeatability is within 0.2%
Each ring is supplied complete with calibration chart made by PC
Large range from 0.5 kN to 100 kN in the following versions:
S370 Serie with dial gauge 0.01 mm graduation
S371 Serie with dial gauge 0.001 mm graduations
S372 Serie with digital gauge 0.001 mm graduation, including battery and RS232 port to PC connection.

Max. Capacity Dial gauge Dial gauge Digital gauge Height Weight
kN 0.01 mm 0.001 mm 0.001 mm - RS232 mm kg
0.5 S370 S371 S372 210 1.6
1 S370-01 S371-01 S372-01 210 1.7
2 S370-02 S371-02 S372-02 210 1.8
3 S370-03 S371-03 S372-03 210 1.9
5 S370-04 S371-04 S372-04 210 2
10 S370-05 S371-05 S372-05 210 2.2
15 S370-06 S371-06 S372-06 210 2.5
20 S370-07 S371-07 S372-07 210 3
30 S370-08 S371-08 S372-08 210 3.5
40 S370-09 S371-09 S372-09 210 3.9
50 S370-10 S371-10 S372-10 210 7.2
60 S370-11 S371-11 S372-11 210 7.7
100 S370-12 S371-12 S372-12 210 10.2

S374

S370-02

S371-08S

S372-11

ACCESSORIES SPARE

Stop electrical safety device to stop the machine when reaching S373-05 COUPLING DEVICE between the dial indicator and the
the max. capacity of the ring, to prevent any overload damage. load ring.
For ordering you have to add the letter “S” at the end of the load
ring code.
Ex.: S370-09S
S374 Stem mechanical brake device, it holds the max.
reached value on the dial gauge, with manual zero
setting.
S374-02 Ball seat, complete with connector, for an articulated
coupling to the testing machine.

Tel: +44 (0) 1442 402770

 E: [email protected]

574 RETURN TO HOMEPAGE

SECTION S | SOIL

DIAL INDICATORS ACCESSORIES

Foreseen on different machines and equipments described in this
catalogue. S380 MAGNETIC DIAL HOLDER, comprising a fix rod and an
Diameter of the dial: 60 mm, 80 mm mod. S379-01 with clockwise adjustable rod.
rotation. MAGNETIC BASE FORCE 25 kg approx.
S374 STEM BRAKE DEVICE to hold the max. reached value on
Model Travel mm Division mm the dial gauge.
S375 5 0.001 S380-01 REAR MOUNT of the dial indicator.
S375-01 12 0.002
S376 10 0.01
S390
S377 25 0.01 CALIBRATION UNIT FOR EXTENSOMETERS AND
S378 30 0.01 DIAL GAUGES
S379 50 0.01 This Appliance can be used to check the displacement calibration of
S379-01 100 0:01 extensometers, dial gauges, transducers etc.
Composed by:
Aluminium frame,
Delicate moving saddle,
DIGITAL DIAL INDICATORS Digital micrometric head 50 mm travel,
Including battery and RS 232 port for PC connection.
resolution 0.001 mm,
Model Travel mm Division mm error limit ± 0.003 mm
Sample holder to fit dial gauges with
S382-01 12.7 0.001 stem having 8 mm diameter
S383 25.4 0.001 (different sample holders are available on
demand).
Weight: 18 kg approx.
ACCESSORY

S382-13 CABLE to connect S382-01 and S383 to PC through

USB port for direct visualization and recording of the
measurement.

S390

S379
S376
S380

S378

S375

S374 S383
S377

S382-01

Tel: +44 (0) 1442 402770