【Panel Design】
Top view
GW1101-1DI(3IN1)-DB-P(12-48VDC)
Modbus Gateway
Quick Installation Guide
Bottom view
Front View
3onedata Co., Ltd. 1. Terminal block for power input
Address: 3/B, Zone 1, Baiwangxin High Technology 2. Reset button
Industrial Park, Xili, Nanshan District, 3. 100M copper port
Shenzhen 4. RS-232/485/422 3IN1 serial port
Website: www.3onedata.com 5. Power supply indicator PWR
Tel: +86 0755-26702688 6. Running indicator RUN
Fax: +86 0755-26703485 7. Copper port indicator LINK
8. Serial port transmitting indicator
【Package Checklist】
9. Serial port receiving indicator
Please check whether the package and accessories are intact
10. Lug
while using the device for the first time.
1. Modbus gateway × 1 2. Power adapter 【Mounting Dimension】
3. Straight-through cable 4. Certification Unit: mm
5 Warranty card
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【Product Overview】 Left view and right view
The product is managed wall-mounted industrial Modbus
gateway.The model is GW1101-1DI(3IN1)-DB-P(12-48VDC)
(1 3IN1 serial port with isolation +1 100M copper port + 1
12~48VDC power supply ).
【Serial Port Connection】
This device provides 1 3IN1 serial port,
which supports RS232, RS485 and RS422
at the same time. The interface type is DB9
male and its pin definitions are as follows:
PIN RS-232 RS-422 RS-485
1 - T+ D+
2 RXD T- D-
3 TXD R+ -
【Wall-mounted Device Disassembling】
4 DTR R- -
Step 1 Device power off.
5 GND GND GND
Step 2 Unscrew the screw on the wall about 2mm.
6 DSR - -
Step 3 Lift the device upward slightly; take out the device,
7 RTS - -
disassembling ends.
8 CTS - -
9 - - -
Notice before power on:
Notice Before Mounting: 【Checking LED Indicator】
Power ON operation: First insert the power supply
Don't place or install the device in area near water or The device provides LED indicators to monitor the device
terminal block into the device power supply interface,
moist, keep the relative humidity of the device working status with a comprehensive simplified
and then plug the power supply plug contact and power
surrounding between 5%~95% without condensation. troubleshooting; the detailed status of each LED is described
on.
Before power on, first confirm the supported power in the table as below:
Power OFF operation: first unpin the power plug, then
supply specification to avoid over-voltage damaging the LED Indicate Description
remove the power line, please note the operation order
device.
above. PWR is connected and running
The device surface temperature is high after running; ON
normally
please don't directly contact to avoid scalding. 【Power Supply Connection】 PWR
PWR is disconnected and running
This device provides 1 DC power supply which OFF
【Wall-mounted Device Mounting】 abnormally
is 3-pin 5.08mm pitch terminal block, the power
Step 1 On the wall of device mounting, place the device on
supply supports non-polarity. Power supply The device is powered on or the
the wall for reference or refer to the mounting ON
range: 12~48VDC. The pin definitions of the terminals are device is abnormal.
dimension to mark two screw positions. The device is powered off or the
shown as follows: RUN OFF
Step 2 Nail M4 screws on the wall and keep 2mm device is abnormal.
PIN 1 2 3
interspace reserved. Definition V+ FG V- Blink once per second, device is
Blinking
running normally.
Step 3 Hang the device on two screws and slide
【Reset Button Setting】 Copper port has established an
downward, then tighten the screw to enhance This device provides 1 reset button, press the button for 4-5S ON
LINK active network connection.
stability, mounting ends. then release it to restore factory defaults.
Blinking Copper port is in a network activity
state. Protection grade IP40 (metal shell)
Copper port has not established an Note:
OFF
active network connection. The default IP address of the device is “192.168.1.254”.
The default user name and password of the device is
No data or abnormal data is being
OFF “admin”.
TX transmitted through serial port.
If the user name or password is lost, user can restore it
Blinking Serial port is transmitting data. to factory settings via restore button or management
Serial port is not receiving data or software; all modified configurations will be cleared
OFF after restoring to factory settings, so please backup
RX receiving data abnormally
configuration file in advance.
Blinking Serial port is receiving data. Please refer to user manual for specific configuration
method of logging in to WEB interface and other
【Logging in to WEB Interface】
configurations about network management function.
This device supports WEB management and configuration.
Computer can access the device via Ethernet interface. The 【Specification】
way of logging in to device’s configuration interface via IE Panel
browser is shown as below: 100M Copper Port 10/100Base-T(X) self-adapting
Step 1 Configure the IP addresses of computer and the RJ45 port
device to the same network segment, and the Serial Port RS-232/485/422 3IN1 serial port,
network between them can be mutually accessed
DB9 interface
Step 2 Enter device’s IP address in the address bar of the
Indicator Power indicator, network Link/Act
computer browser.
indicator, serial port transmission
and receiving data indicator,
running indicator
Step 3 Enter device’s username and password in the login
Power Supply
window as shown below.
Input power supply 12～48VDC
Access terminal block 3-pin 5.08mm pitch terminal
blocks
Power Consumption
No-load 0.9W@12VDC
Full-load 1.1W@12VDC
Working Environment
Working temperature -40~75℃
Storage temperature -40~85℃
Step 4 Click “OK” button to login to the WEB interface of
Working humidity 5%～95%(no condensation)
the device.
