TYPE-21/21a BALL VALVE WITH SERIES 19 SMART MODULATING
ELECTRIC ACTUATOR
Specifications
Motor Type: Reversing, brushless DC
Sizes: S20 for 1/2” – 2” ball valves
S50 for 2-1/2” – 3” ball valves
S110 for 4” ball valves
Torque: 177 in-lbs to 973 in-lbs
Voltage: 95 VAC to 265 VAC multi-voltage
Amp Draw: 0.18 Amp for S20
0.24 Amp for S50
0.84 Amp for S110
Max Ambient Temp: 150° F
Standard Features (1/2” – 4”)
• Compact: Perfect for OEM and skid L W
manufacturers•
• OLED Screen: Displays input command, position
status, alert conditions
• Push Buttons: Used to calibrate/adjust end positions, H2
local controls
• Multi-voltage: 95 VAC to 265 VAC or 24 VAC/VDC
• Motor: Reversing, brushless DC motor H
• Gear Train: Permanently lubricated steel gears
• Corrosion Resistant Enclosure: NEMA 4X ABS H1
(T-21)
enclosure with stainless steel trim H3
(T-23)
• ISO mounting configuration
• Electrical Connection: NEMA 4X cable gland with two-
meter cable T-23 ONLY
• Position Indication: Highly visible beacon position
indicator T-23 ONLY
• LED Alarm Indication: BLUE fault
• Manual Override: Manually cycle valve via electroless Dimensions (inch)
nickel-plated hex key
Size 1/2” 3/4” 1” 1-1/4” 1-1/2” 2” 2-1/2” 3” 4”
• Selectable Control Signal: User can select 4-20 mA,
0-20 mA, 0-10 VDC, 2-10 VDC, or 1-5 VDC (size 20 is L 4.01 4.01 4.01 4.01 4.01 4.01 5.12 5.12 6.69
specifically a current control signal or a voltage control W 2.76 2.76 2.76 2.76 2.76 2.76 4.33 4.33 4.52
signal)
• Reverse Acting: User can select standard operation H 2.76 3.01 3.29 3.64 3.98 4.43 5.12 5.47 6.97
or reverse acting H1 1.14 1.38 1.54 1.85 2.17 2.60 2.83 3.35 4.33
• Selectable Fail Position: If control signal is lost, the
unit can be calibrated to fail as is, fail open, or fail close H2 3.54 3.54 3.54 3.54 3.54 3.54 4.72 4.72 4.80
• Transmitter: Current or voltage transmitter (matching Model S20 S20 S20 S20 S20 S20 S50 S50 S110
the control signal) is standard equipment
• Alarm Contacts: Dry contacts rated 0.1 Amp @ 250 Weight (lbs)
VAC, 0.5 Amp @ 30 VDC for alarm status (over torque,
as an example) Size 1/2” 3/4” 1” 1-1/4” 1-1/2” 2” 2-1/2” 3” 4”
• Space Heater: Internally wired to limit condensation Weight 2.7 2.9 3.4 3.8 4.9 6.7 10.2 13.7 29.6
• CE Compliant: All actuators are CE labeled and
compliant
• 75% Duty Cycle: Extended duty cycle is ideal for high Engineering Data
cycling/modulating applications 95-265 VAC 24 VAC/VDC Cycle time
• Output Torque: Series 19 electric actuators have an Torque per 90
Model
output torque range from 177 in-lbs to 973 in-lbs (in-lbs) Amp Duty Amp Duty degrees
• QR Code: Links to user manual; includes wiring Draw Cycle Draw Cycle (seconds)*
schematic S20 177 0.18 75% 0.96 75% 10
• Simple Wiring: Wiring technique is the same for all
voltage units S50 442 0.24 75% 1.20 75% 10
• Local Controls: Used with OLED and push buttons, a S110 973 0.84 75% 4.80 75% 10
user can locally open or close units via password
Amp draw is considered locked rotor
*Cycle times are approximate
Duty cycle shown for ambient temp (73° F)
26 www.asahi-america.com • [email protected] • Tel: 800-343-3618 • 781-321-5409 • Fax: 800-426-7058 ASAHI/AMERICA
Rev 2203C
TYPE-21/21a BALL VALVE WITH SERIES 19 SMART MODULATING
ELECTRIC ACTUATOR
Wiring Diagrams
S20
BLUE N/-
CONTROL
AC-DC
MOTOR
M
RED L/+
POSITION
SENSOR VOLTAGE
REGULATOR
BROWN
TRANSMITTER
TRANSMITTER SEE NOTE 5
WHITE SIGNAL/TRANSMITTER NEGATIVE
16 BYTE
M.C.U.
GREY CONTROL SIGNAL POSITIVE
1.3" RELAY
OLED
SCREEN BLACK
ALERT
ALARM_OUTPUT
PURPLE
YELLOW/
NOTES: GREEN
1. NOT ALL WIRES FROM FLYING LEADS ARE USED
2. RED AND BLUE ARE POWER SUPPLY
3. GREY AND WHITE ARE CONTROL SIGNAL INPUT
4. BROWN AND WHITE ARE TRANSMITTER OUTPUT
5. 10K RESISTOR SHALL BE USED FOR VOLTAGE
TRANSMITTER, OR 250Ω RESISTOR FOR CURRENT
TRANSMITTER
6. USER CAN SET "NO CONTROL" DEFAULT POSITION IN
FIRMWARE SETTINGS (FAIL IN PLACE, OPEN, CLOSE)
FOR 4-20mA, 1-5V, AND 2-10V CONTROL SIGNAL.
STANDARD IS FAIL IN PLACE. THIS SETTING IS NOT
POSSIBLE IF USING A CONTROL SIGNAL OF 0-20mA, 0-
5V, OR 0-10V
7. HEATER IS INTERNALLY WIRED & OPERATIONAL
AS LONG AS ACTUATOR IS POWERED
S50-S110 BLUE N/-
AC-DC
MOTOR
DRIVER
RED L/+
M
YELLOW/
GREEN
POSITION SENSOR
RELAY
VOLTAGE
REGULATOR
BLACK
ALARM
GREEN
10K X 2
PURPLE VOLTAGE CONTROL SIGNAL POSITIVE
16 BYTE M.C.U.
1.3"
OLED 150Ω GREY CURRENT CONTROL SIGNAL POSITIVE
SCREEN
V/I_OUT BROWN CURRENT TRANSMITTER POSITIVE
V/V_OUT
WHITE SIGNAL/TRANSMITTER NEGATIVE
NOTES: ORANGE VOLTAGE TRANSMITTER POSITIVE
1. NOT ALL WIRES FROM FLYING LEADS ARE USED
2. RED AND BLUE ARE POWER SUPPLY
3. PURPLE AND WHITE ARE VOLTAGE CONTROL SIGNAL,
ORANGE AND WHITE ARE VOLTAGE TRANSMITTER
4. GREY AND WHITE ARE CURRENT CONTROL SIGNAL, BROWN
AND WHITE ARE CURRENT TRANSMITTER
5. 10K RESISTOR SHALL BE USED FOR VOLTAGE TRANSMITTER, OR
250Ω RESISTOR FOR CURRENT TRANSMITTER
6. USER CAN SET "NO CONTROL" DEFAULT POSITION IN
FIRMWARE SETTINGS (FAIL IN PLACE, OPEN, CLOSE) FOR 4-
20mA, 1-5V, AND 2-10V CONTROL SIGNAL. STANDARD IS FAIL
IN PLACE. THIS SETTING IS NOT POSSIBLE IF USING A CONTROL
SIGNAL OF 0-20mA, 0-5V, OR 0-10V
7. HEATER IS INTERNALLY WIRED & OPERATIONAL
AS LONG AS ACTUATOR IS POWERED
Sample Specification
All Series 19 SAV smart modulating electric actuators shall have a brushless DC motor that accepts multiple voltages, permanently
lubricated steel gears, NEMA 4X ABS enclosure with stainless steel trim, visual beacon indication, ISO 5211 valve mounting platform,
manual override, and be CE compliant. Standard features shall include a heater, transmitter, field selection of various control signals,
field selection of fail position (upon loss of command signal), one set of dry contacts for alarm reporting, LED indicator for alarm
conditions, an OLED screen with push buttons, local controls, and a QR code that links to its user manual and wiring schematic.
ASAHI/AMERICA www.asahi-america.com • [email protected] • Tel: 800-343-3618 • 781-321-5409 • Fax: 800-426-7058 27
Rev 2203C
