Unknown date
Unknown author
1. Which diamonds correspond to the contour labels?
Your answer: 3, 4
Answer is correct
2. Which diamond corresponds to the Depth greater than Safety Depth?
Your answer: 5
Answer is correct
3. Soundings less than Safety Depth within the Safety Frame trigger ...
Your answer: neither alarm no indication within the Safety Frame
Answer is correct
4. Which extension does ENC permit usually has?
Your answer: permit.txt
Answer is correct
5. What will trigger the
WARNING
on ECDIS in route monitoring mode?
Your answer: XTE exceeded, Actual course change
Answer is partly correct
6. Safety Depth and Safety Contour shall be calculated ...
Your answer: for each route leg
Answer is correct
7. It is generally recommended to set ...
Your answer: Safety Contour = Safety Depth
Answer is correct
8. What does this ENC symbol mean?
Your answer: Rock which covers and uncovers or is awash at low water
Answer is correct
9. Match the chart symbols to their description:
Your answer:
Dangerous wreck, depth unknown
Foul ground
Land as point at small scale
Isolated danger of depth less than the safety contour
Answer is correct
10. What is the share of navigational incidents from maritime casualty statistics
as per EMSA?
Your answer: About 50%
Answer is correct
11. Isolated danger with a depth less than the Safety Contour setting...
Your answer: Will trigger the indication on ECDIS on appearing withing the Safety
Frame
Answer is correct
12. Practical formula to estimate increase of draft due to pitching is to take it
as...
Your answer: 0.5 of the observed wave height
Answer is correct
13. Which diamonds correspond to the soundings greater than Safety Depth?
Your answer: 1, 4
Answer is partly correct
14. Which diamond corresponds to the Safety Contour?
Your answer: 1
Answer is correct
15. What is the correct equation to estimate required Rate of Turn?
Your answer: 1.05 X Speed / Radius
Answer is correct
16. Which of the mentioned ECDIS options should be ON on the route monitoring
stage?
Your answer: Past Track, RADAR and AIS overlays, 'Position Difference' alarm
Answer is correct
17. On modern ECDIS systems Safety Frame triggers the
INDICATION
on ...
Your answer: Crossing the area with special conditions, ARPA tracked targets
Answer is partly correct
18. Each ECDIS onboard the vessel has individual User Permit Number.
Your answer: False
Answer is correct
19. Which of the mentioned ENC layers may be temporarily OFF to improve display
visibility on the planning stage?
Your answer: Highlight Info, Text, Accuracy (ZOC)
Answer is correct
20. Which statements are correct about the Safety Frame (Look Ahead Frame)?
Your answer: Safety Frame is able to recognize navigational objects on ENC and
trigger appropriate alerts, Safety Frame does not recognize RADAR or AIS targets
Answer is correct
21. How does change of ENC Safety Depth setting affect the display?
Your answer: ECDIS Highlights soundings, which are less than the specified value in
bold black
Answer is correct
22. Pick the correct definition for the Caution.
Your answer: Awareness of a condition which still requires attention out of the
ordinary consideration of the situation or of given information
Answer is correct
23. If we set Safety Contour = 18m will the individual soundings less than 18m be
highlighted by the Safety Frame?
Your answer: Yes, they will be highlited with yellow color
Answer is correct
24. According to the course recommendations Medium Risk Area has following
characteristics:
Your answer: Outside Safety Contour; Depth < 2 x Drafts; ETA Hazard < 30 min
Answer is correct
25. What are the recommended XTE limit settings in this course for Harbour / Port
Approaches?
Your answer: 0.1 – 0.5 nm
Answer is not correct
26. Calculate the ship's Squat by simplified Barras formula. Block Coefficient =
0.56; Speed = 8 knots; H/d = 1.25. Open waters
Your answer: 1.44
Answer is not correct
27. Setting a centered track in two-way channels and fairways to be able to reverse
it for the use of an upcoming passage plan is an acceptable procedure for ECDIS
Your answer: False
Answer is correct
28. It is unnecessary to draw NO-GO areas inside the Safety Contour, as Safety
Frame will recognize all the dangerous soundings, basing on the Safety Depth value
Your answer: False
Answer is correct
29. What is shown on this picture in blue rectangles?
Your answer: Date-dependent object
Answer is correct
30. Mariner shall keep SCAMIN ...
Your answer: OFF because with SCAMIN ON individual soundings may disappear, even
with the small change of display scale in relation to ENC compilation scale
Answer is correct
31. A shallow contour is only for an additional indication of the underwater
topography of the already 'un-safe' water
Your answer: True
Answer is correct
32. Which scale mode is shown on display?
Your answer: Overscale
Answer is correct
33. What is the purpose of chart permits in ECDIS?
Your answer: It is required to decrypt ENCs
Answer is correct
34. Which statements are correct about the Safety Frame (Look Ahead Frame)?
Your answer: Safety Frame is able to recognize navigational objects on ENC and
trigger appropriate alerts, Safety Frame does not recognize RADAR or AIS targets
Answer is partly correct
35. ENC's are installed, decrypted and updated in ECDIS in accordance with IHO
standard ...
Your answer: S-63
Answer is correct
36. It is normal practice to calculate tide only for the primary port. There's
usually a small difference with a secondary port.
Your answer: False
Answer is correct
37. Temporary and preliminary notices are included into the ENC updates for all
countries.
Your answer: True
Answer is not correct
38. What are the recommended XTE limit settings in this course for Open Sea (>12 nm
from shore)?
Your answer: Equal or more than Ship Breadth – 0.1 nm
Answer is not correct
39. Calculate ZOC correction for the sounding highlighted on the ENC:
Your answer: 0.7 m
Answer is not correct
40. Calculate ZOC correction for the sounding highlighted on the ENC:
Your answer: 1.4 m
Answer is not correct
Viewed using Just Read
Report an error
