OPTOTRONIC® LED Power Supply
OTi DALI DIM 1-4CH D
1) 6)
4) 5)
9)
picture only for
7)
reference, valid print
on product
2) 3) 8)
One pole of the output must not be touchable during PWM dimming if supplied by 48 V DC or alternatively
a limitation of the input voltage to maximum 24V DC.
Year 10) Week 11)
42±0.5 20 20 O2020
3.8
175.5±0.5 20±0.5
181±0.5
DALI Mode (DT6/DT8) for LMS
DALI Controller
A B C D PLUG & PLAY DALI
A 597 312 00 72
DALIPORT POWER PROFESSIONAL
OFFLINE
CONTROLLER-4
Made in Italy
by OSRAM
RELAY
K1 K2 K3 K4 ERROR
DALI
wire preparation
USB push in
SERVICE
s: 0.5 – 2.5°
SELECT ON/OFF/DIM f: 0.5 – 1.5°
ta (°C)
0...+40 10 - 12 mm 100...
240V
K1 K2 K3 K4 +A – +B– +C – + D – NC L L
5A 5A 5A 5A DA DA DA DA
DC +
12V/24V/48V –
1#
∙
∙
∙
DT6 mode: each CH = 1 addr.
DT8 mode: 1 addr, CH1=CH3 & CH2=CH4
N#
OPTOTRONIC® LED Power Supply
DALI Mode (DT6 for DALI MCU, DT8 for DALI MCU TW)
DALI
DC +
12V/24V/48V –
WW
CW
1#
∙
∙
∙
DT6 mode: each CH = 1 addr. WW
DT8 mode: 1 addr, CH1=CH3 & CH2=CH4
CW
N#
DALI MCU or DALI MCU TW
Touch DIM Mode
In addition to operation on DALI control units, OTI DALI DIM 1-4CH D offers the possibility of Touch DIM operation.
N
AC L
DC +
12V/24V/48V –
1#
LNS ∙
∙
∙
Touch DIM
Sensor
N# (N=16)
Push-button
- Touch DIM mode 1* (default mode):
The switch-on value is always the last dimming level before the light was switched off. After a mains voltage
interruption, you get the same light level before the interruption happened.
- Touch DIM mode 2:
The switch-on value is stored by double-clicking.
After a mains voltage interruption as well, the dimmer turns on at the stored light value.
This means, after a short press of the push-button, the dimmer dims to this stored light value.
<0.5s ON/OFF
>0.5s Dim
Button (ON)
(OFF)
2
OPTOTRONIC® LED Power Supply
Touch DIM Mode (Tunable White)
N
AC L
DC +
12V/24V/48V –
WW
CW
WW
CW
1000V 1A, 1#
LNS ∙
e.g. 1N4007/M7 ∙
∙
WW
Touch DIM
Sensor CW
WW
CW
N# (N=16)
Touch Dim mode:
1 addr, CH1 = CH3 & Push-button 1 Push-button 2
CH2 = CH4 Dimming Change CCT
ON/OFF ON/OFF
<0.5s ON/OFF <0.5s ON/OFF
>0.5s Dim >0.5s WW CW
Button 1 Button 2
>0.5s WW CW
Corridor Mode
It is possible to connect the OTI DALI DIM 1-4CH D directly to commercially available motion sensors. The Corridor
Function is triggered by a switching signal, i.e. the voltage of the supply line (220–240 V, 50/60 Hz) is switched to the
DALI control line inputs (DA, DA; see the diagram below). A preset “out-of-the-box” luminous flux program launches
upon triggering. Three light value ranges and three-time ranges are available for this purpose.
N
AC L
DC +
12V/24V/48V –
1#
∙
∙
∙
Motion sensor
General curve: N# (N=16)
Light value
B
I II III IV
230V D0 F1 T1 Time
ON
A: 100%, D0 120S, F1: 32S
OFF B: 10%, T1: unlimited
3
1) Constant voltage LED dimmer; 2) DALI 2 certified; 3) tc point; 4) Main Input; 5) Output; 6) Wire preparation; 7) DALI Input;
8) Dip switch:
type DT6 DT8
DIP1 ON, DT6 OFF, DT8
ON/ON CH1
OFF/ON CH1, CH2 CH1=CH3=WW,
DIP2/DIP3 N.A
ON/OFF CH1, CH2, CH3 CH2=CH4=CW
OFF/OFF CH1, CH2, CH3, CH4
ON Touch Dim ON Touch Dim
DIP4
OFF Corridor OFF Corridor
9) Max channel load:
Channels DT6 DT8
12V 24V 48V 12V 24V 48V
CH1 120W 240W 240W 60W 120W 120W
CH2 60W 120W 120W 60W 120W 120W
CH3 60W 120W 120W 60W 120W 120W
CH4 60W 120W 120W 60W 120W 120W
All 120W 240W 240W 120W 240W 240W
Min each CH load>20W
For max cable length, please refer to datasheet of the matching Constant Voltage driver in your system.
10) Year; 11) Week
The OTI DALI DIM 1-4CH D is connected between an OPTOTRONIC power supply and an LED-module. The permissible
input voltage, mains frequency and temperature range of the dimmer must not be exceeded. Connect only 12V, 24V or 48V
LED load and power supplies to the OTI DALI DIM 1-4CH D.
L N S Touch DIM
Sensor
DALI
Cable length: Max ≤10m Cable length: Max ≤25m
......... Max 16pcs ......... Max 64 address
DALI Mode DALI Mode DALI Mode
DALI Control DALI Control DALI Control
System System System
Touch DIM Mode Touch DIM Mode Touch DIM Mode
For user instructions in other languages please visit product webpage:
www.osram.com/optotronic
OSRAM GmbH
EN 61347-1 Berliner Allee 65
EN 61347-2-13
EN 55015
86153 Augsburg
EN 61547
C10449059
G15115733
Germany
EN 62384 2022-08-15 www.osram.com
