Module No.

1922 1922-1

GENERAL GUIDE
• Press C to change from mode to mode.
• After you perform an operation in any mode, pressing C returns to the Timekeeping Mode.
• If you do not press any button for a few minutes while making settings in any mode (indicated when settings are flashing), the watch automatically clears the setting screen (settings stop
flashing) and returns to the normal display for the mode you are in.
• This watch returns to the Timekeeping Mode whenever you hold down the C button for one or two seconds. If you ever lose track of what mode you are in or what you should do next,
hold down C to return to normal timekeeping.
• In any mode press L to illuminate the display.
Timekeeping Mode Countdown Alarm Mode Stopwatch Mode Alarm Mode Dual Time Mode

TIMEKEEPING MODE To use the countdown alarm

1. Press D while in the Countdown Alarm Mode to start the countdown alarm.
PM indicator Month To set the time and date 2. Press D again to stop the countdown alarm.
1. Hold down A while in the Timekeeping Mode until the • You can resume countdown alarm operation by pressing D .
Day of week Day seconds digits flash on the display because they are 3. Stop the countdown alarm and then press B to reset the countdown time to its
selected. starting value.
2. Press C to change the selection in the following se- • When the end of the countdown is reached and auto repeat timing is off, the alarm
quence. sounds for 10 seconds or until you stop the alarm by pressing any button. Count-
down timing stops and the countdown time is automatically reset to its starting
Seconds Hour Minutes value after the alarm stops.

To turn auto repeat timing, the progress indicator and vibration alarm
12/24-Hour Format
ON/OFF
Hour Seconds 1. Hold down A while in the Countdown Alarm Mode. The hours digits flash on the
Minutes display because they are selected. Press A again to move the flashing to the auto
Day ofweek Day Month repeat ON/OFF setting, which is indicated by the AUTO-RE indicator flashing on
Vibration alarm on indicator the display.
2. Press D or B to toggle auto repeat on and off.
3. While the seconds digits are selected (flashing), press D to reset the seconds to 3. Press C to move the flashing to the progress indicator ON/OFF setting, which is
00. If you press D while the seconds count is in the range of 30 to 59, the seconds indicated by the SOUND indicator flashing on the display.
are reset to 00 and 1 is added to the minutes. If the seconds count is in the range 4. Press D or B to toggle the progress indicator on and off.
of 00 to 29, the minutes count is unchanged. • Note that the SOUND indicator appears regardless of whether you are using the
4. While any other digits (beside seconds) are selected (flashing), press D to in- audible alarm tone or vibrator. Steps 5 and 6 below control whether an alarm oper-
crease the number or B to decrease it. While the 12/24-hour format setting is ation produces an audible tone or vibration.
selected, press D or B to toggle it between 12 and 24. While the day of the week 5. Press C to move the flashing to the vibration alarm ON/OFF setting, which is indi-
is selected (flashing), press D to advance to the next day or B to return to the cated by the indicator flashing on the display.
previous day. 6. Press D or B to toggle the vibration alarm on and off.
7. Press A to return to the Countdown Alarm Mode.
• Except for when adjusting the seconds or setting the 12/24-hour format, holding • When the end of the countdown is reached while auto repeat is on, the alarm sounds,
down a button changes the current selection at high speed. but the countdown restarts from the beginning without stopping. You can stop the
• When the 12-hour format is selected, the indicator P appears on the display to countdown by pressing D and manually reset to the start time by pressing B.
indicate “P.M.” times. There is no indicator for “A.M.” times. • If you set a starting time of 10 seconds or less and have Auto Repeat turned on, the
• When the 24-hour format is selected, the indicator 24 appears on the display. countdown alarm tone (which normally sounds for 10 seconds) sounds for only one
5. After you set the time and date, press A to return to the Timekeeping Mode. second.
• When the progress indicator is turned on, the watch beeps as the countdown time
passes the 10, 5, 4, 3, 2, and 1-minute marks, and the 50, 40, 30, 20, 10, 5, 4, 3, 2,
and 1-second marks.
ABOUT THE BACKLIGHT
In any mode, press L to illuminate the display for about two seconds.
• The backlight of the watch employs an electro-luminescent (EL) light, which loses
illuminating power after very long use. STOPWATCH MODE
• The illumination provided by the backlight may be hard to see when viewed under Target time on indicator The Stopwatch Mode lets you measure elapsed time, split
direct sunlight. times, and two finishes. The range of the stopwatch is 23
• The backlight automatically stops illuminating whenever an alarm sounds. Current time hour, 59 minutes, 59.99 seconds. You can also have an
alarm sound when a target time is reached. The Stop-
watch Mode also features an Auto-Start function.

ABOUT THE VIBRATION ALARM

When the Vibration Alarm is turned on, the watch vibrates instead of sounding an
alarm. This lets you use the watch without disturbing others by beeping sounds.
• The Vibration Alarm can be used to replace alarm sounds in the Countdown Alarm,
Stopwatch, and Alarm modes. The Vibration Alarm on/off setting is applied to all
modes. You cannot make different settings for each mode. 1/100 Second
• All explanations in this manual use expressions such as “sounds the alarm” for Minutes
alarm operations. When the Vibration Alarm is turned on, these expressions should Seconds
be understood to mean “causes the watch to vibrate.” Mode indicator
• Watches with a metal band may produce a noise when a vibration operation is
performed. This is due to vibration of the metal band, and does not indicate mal-
function of the watch. (a) Elapsed time measurement

Start Stop Re-start Stop Clear

COUNTDOWN ALARM MODE
(b) Split time measurement
Progress Auto repeat The countdown alarm can be set within a range of 1 second
indicator on on indicator to 24 hours. When the countdown reaches zero, an alarm
Current time sounds for 10 seconds or until you press any button.
Start Split Split release Stop Clear
To set the countdown start time
(c) Split time and 1st-2nd place times
1. Hold down A while in the Countdown Alarm Mode. The
hours digits flash on the display because they are se-
lected.
2. Press C to change the selection in the following se- Start Split Stop Split release Clear
quence. First runner Second runner Record time of
finishes. finishes. second runner.
Hour Minutes Seconds Record time of
Minutes 1/10 first runner.
Second
Seconds About the Auto-Start function
Mode indicator With the Auto-Start function, the watch performs a 5-second countdown. When the
Vibration alarm on indicator countdown reaches zero, stopwatch operation starts automatically. During the final
three seconds of the countdown, a beeper sounds with each second.
3. Press D to increase the selected number or B to decrease it. Holding down either
To turn the Auto-Start function on and off
button changes the selection at high speed.
• Press D and B at the same time to clear the starting time to 0:00' 00". While the lower display is showing all zeros in the Stopwatch Mode, press B to
• To set the starting value of the countdown time to 24 hours, set 0:00' 00". toggle it on and off.
4. After you set the countdown start time, press A twice to return to the Countdown • The indicator AUTO-ST appears and 05 is shown in the upper display while Auto-
Alarm Mode. Start is turned on. The AUTO-ST indicator is not shown and the upper part of the
display shows the current time when Auto-Start is turned off.

About the Target Time function

With the Target Time function, an alarm sounds for ten seconds whenever the time
being kept by the stopwatch reaches a target time you have preset.

Downloaded from www.Manualslib.com manuals search engine

 1922-2

To set the target time, to turn the target time on and off, and to turn the vibra- To turn the daily alarm on and off, to turn the hourly time signal on and
tion alarm on and off off, and to turn the vibration alarm on and off
1. While the display is showing all zeros in the Stopwatch
Target time on indicator Mode, hold down A , and the hour digit of the target Press B while in the Alarm Mode to change the status in the following sequence.
time starts to flash because it is selected.
Minutes Hour
2. Press C to change the selection in the following sequence.
Hour Minutes Seconds

Both OFF Daily Alarm Hourly Time Both ON

3. Press D to increase the selected number or B to de- Only Signal Only
crease it. Holding down either button changes the se-
lection at high speed.
• Press D and B at the same time to clear the setting to
0:00' 00".
Seconds 4. Press A to move the flashing to the target time ON/
Mode indicator OFF setting, which is indicated by the SOUND indica-
tor flashing on the display.
Vibration alarm on indicator
Both ON Hourly Time Daily Alarm
5. Press D or B to toggle the target time on and off. Vibration ON Signal Only Only
• Note that the SOUND indicator appears regardless of whether you are using the (no sound)
audible alarm tone or vibrator. Steps 6 and 7 below control whether an alarm oper-
ation produces an audible tone or vibration.
6. Press C to move the flashing to the vibration alarm ON/OFF setting, which is indi-
cated by the indicator flashing on the display.
7. Press D or B to toggle the vibration alarm on and off.
8. Press A to return to the Stopwatch Mode.
• The alarm on indicator (
on indicator (
are turned on.
/ ), the Hourly Signal on indicator ( y) and vibration
) are shown on the display in all modes while these functions

To test the alarm sound

Important! Hold down B while in the Alarm Mode to sound the alarm.
The alarm will not sound if you do not turn on the target time.
• Press A , C or L to stop the alarm after it starts to sound. The Vibration Alarm is activated while the is on the display. Otherwise, the
Vibration Alarm is not activated and an audible tone sounds for alarms.
• Note that pressing B also changes the alarm and the hourly time signal ON/OFF
settings.
ALARM MODE
Alarm on indicator When the Daily Alarm is turned on, an alarm operation
Hourly time signal on (20-second tone or 10-second vibration) is performed at DUAL TIME MODE
indicator the preset time each day. Press any button to stop the
alarm after it starts to sound. When the Hourly Time Sig- Current time The Dual Time Mode lets you keep track of the time in
Current time nal is on, the watch beeps every hour on the hour. another time zone. You can also select the timekeeping
format (12-hour or 24-hour) separately from the Timekeep-
ing Mode.
To set the alarm time
1. Hold down A until the hour digits start to flash on the
display. The hour digits flash because they are select-
To set the Dual Time
ed. 1. Hold down A while in the Dual Time Mode. The hour
• This operation will switch the Daily Alarm on automati- digits flash on the display because they are selected.
cally. 2. Press C to change the selection in the following se-
2. Press C to change the selection in the following se- quence.
Hour Minutes quence. Hour
Hour Minutes
Mode indicator Minutes
Hour Minutes
Vibration alarm on indicator
Mode indicator
3. Press D to increase the selected digits and B to de-
3. Press D to increase the selected digits and B to decrease them. Holding down crease them. Holding down either button changes the
either button changes the selection at high speed. selection at high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select 4. After you set the time, press A to return to the Dual Time Mode.
for normal timekeeping. • In the Dual Time Mode, the seconds count is synchronized with the seconds count
• When setting the alarm time using the 12-hour format, take care to set the time of the Timekeeping Mode.
correctly as morning (no indicator) or afternoon (P). • In the Dual Time Mode, press B to toggle between the 12-hour and 24-hour for-
4. After you set the alarm time, press A to return to the Alarm Mode. mats.

Downloaded from www.Manualslib.com manuals search engine