SOFTWARE USER GUIDE

DupliM USB Duplication Suite

1:10 USB 3.0 Flash

Duplicator CC™

Part No. 210100

Copyright/Model Identification

The content of this manual is for informational purposes only and is subject
to change without notice.

This manual is copyrighted with all rights reserved. Under copyright laws,
this manual and the software described within may not be copied, except in
the normal use of the product(s) described within or to make a backup copy.

Copyright© 2022
DupliM Inc.
21722 Lassen Street
Chatsworth, CA 91311 U.S.A.

www.duplim.com

DupliM and 1:10 USB 3.0 Flash Duplicator CC™ are trademarks of DupliM
Inc.

Please record the following information to help expedite any warranty claim:

Model No. ______________________ Serial No.______________________

Date Purchased _________________________________________________

Place of Purchase _______________________________________________

www.duplim.com
Table of Contents

Introduction..................................................................................................1
Initial System Setup................................................................................. 1
For Ease of Use........................................................................................2
Using the USB Duplication Suite Software........................................... 5
Source Tab............................................................................................... 6
Destination Tab........................................................................................7
Data Copy Only....................................................................................... 9
Format (FAT, FAT32, exFAT, NTFS)..................................................... 10
Format Then Data Copy (FAT, FAT32, exFAT, NTFS).........................12
Port Training..........................................................................................17
Technical Support.....................................................................................19
Technical Support FAX Back Form.......................................................20

www.duplim.com
www.duplim.com
Introduction

Thank you for purchasing a DupliM USB Duplicator. Please read this
Software User Guide thoroughly before using this product.

Initial System Setup

1. Connect the USB cable (included) to the USB port on the back of your
duplicator and to an empty USB port on your computer.
2. Connect the included power cord to the power input on the duplicator
and into an available power outlet.
3. Insert the DupliM USB Duplication Suite Installation and Software
Flash Drive into an available USB port on your computer.
4. Click on Install DupliM USB Duplication Suite to install the
duplication software.
5. Follow the on-screen prompts to complete the installation.
6. Press the power button to power up the DupliM USB Duplicator.
7. The blue power LED will light, and the computer will recognize the
device.
8. Start the USB Duplication Suite duplication software via the icon
on your Desktop or in the Start menu under “All Programs.”

www.duplim.com 1
Introduction

For Ease of Use

To make duplication even easier, we’ve added a feature that lets you match
up the logical drives shown in the USB Duplication Suite software with the
actual physical port position of that drive. To take advantage of this function,
a “Port Training” needs to be performed to match each USB Port to your
Aleratec USB Duplicator. For example, you would likely designate the upper
port on the duplicator Port 1 and so on (see image).

1:10 USB 3.0 Flash

Duplicator CC™

For details please see

section titled Port Training
on page 17 in the manual.

2 www.duplim.com
Using the USB Duplication Suite Software

Main Menu
The USB Duplication Suite’s main menu offers six functions:

1. Data Copy Only

2. Format FAT
3. Format FAT32
4. Format NTFS
5. Format Then Data Copy
6. Port Training

Choose the desired option from the drop down menu located on the Source tab.

When using the USB Duplication Suite, ensure that only the USB flash
drives you wish to operate on are plugged into the duplicator. Remove
all other media from the computer and duplicator before using the USB
Duplication Suite.
www.duplim.com 3
Using the USB Duplication Suite Software

Source Tab
The Source tab has several key functions as listed below.

2. 3.

4.
1.
5.

1. Job Selection List: This drop down menu lists all the available
functions the USB Duplication Suite offers.

2. Add File / Add Folder: Add File/Add Folder buttons allows you to
select any files / folders you would like to copy. These buttons are
available for Data Copy Only or Format Then Data Copy job types.

3. Remove / Clear: The Remove button allows you to remove items listed
in the Add Files box one at a time. The clear button will remove all
items listed in the Add Files box.

4. Full Format: The Full Format check box allows you to specify whether
or not the format job being performed is a full format or a quick format.
Note: quick format is the default setting if Full Format is unchecked.

5. Verify Data: If you wish to verify the Source data files are copied
successfully, you may click the Verify Data check box when applicable.

4 www.duplim.com
Using the USB Duplication Suite Software

Destination Tab

1.

2.
3.

1. Drive List: The drive list will list all drives that are recognized by the
computer. Each drive may be selected or deselected individually by
clicking on the check box next to the corresponding drive letter or USB
port number (See Port Training). The checked drives are the target
drives that will be operated on when the Start button is clicked. Select
the target drives carefully before pressing start.

The Select All button will select all available drives in the list.

The Deselect All button will deselect all drives in the list.

The Refresh button will refresh the drives list. This is necessary if
new drives have been added or removed from the device.

2. Enter Label: The Enter Label box allows you to specify a volume label
for the target drives during a format operation. This is available during
Format and Format Then Data Copy job types.

3. Drives: The drives box displays the number of drives that are being
operated on in the current round.

www.duplim.com 5
Using the USB Duplication Suite Software

Destination Tab
10.

5.

4. 7.

8. 9. 6.

4. Rounds: The rounds box allows you to specify how many rounds of the
selected job type you would like to conduct.

5. Output Window: The output window displays job status updates while
jobs are running or when they have completed.

6. Completed: The Completed box displays the total number of drives

that have been completed for the current job. For jobs with more than
one round, the completed box will be updated after each round is
completed.

7. Rejected: The Rejected box displays the number of drives that have
been rejected due to errors during the copy or verify process.

8. Start Button: Clicking the Start button will initiate the job type that was
selected from the drop down menu in the Source tab.

9. Cancel Button: Clicking the Cancel button will stop the current job
from running.

10. Help Button: The Help button allows you to gain quick access to
relevant sections of the USB Duplication Suite User Guide.

6 www.duplim.com
Using the USB Duplication Suite Software

Data Copy Only

Use this function to copy files or folders to one or more USB flash drive(s).
This function will overwrite any files/folders on the target drive(s) with the
same name as the source files/folders.

1. Start by choosing Data Copy Only from the drop down menu located
on the “Source” tab.

2. On the “Source” tab, click “Add Files” to copy individual files or “Add
Folder” to copy an entire folder. You may add both files and folders.

3. Once all data has been selected, you may choose to verify the data copy
process by checking the “Verify Files” box located on the right of the
drop down menu.

4. Click on the Destination tab, select which drives you would like to
operate on from the drive list.

5. After selecting the drives from the drive list and specifying any options
you may click the Start button located inside the Destination tab to
begin the duplication process.

www.duplim.com 7
Using the USB Duplication Suite Software

Format (FAT, FAT32, NTFS)

There are three format options available in the USB Duplication Suite.
Format FAT, Format FAT32, and Format NTFS. Each option will format the
selected drives and if specified apply a volume label.

By default a quick format will be run. However if you wish to perform a

full format, you must check the “Full Format” box after selecting one of the
three formats.

1. Start by selecting one of the three formats “Format FAT”, “Format

FAT32”, or “Format NTFS” from the drop down menu.
2. If a Full format is desired, check the box labeled Full Format to the
right of the drop down menu.
3. Next, click on the Destination tab.
4. Select the drives that you wish to format.

8 www.duplim.com
Using the USB Duplication Suite Software

Format (FAT, FAT32, NTFS) - continued

5. You can specify a volume label which will be applied to all drives in
the text box under “Enter Label” which is found in the Destination tab.
I. Note: FAT and FAT32 file systems have restrictions on volume
labels which allow for up to 11 characters, not including the following
special characters * ? . , ; : / \ | + = < > [ ]
II. NTFS file systems allow up to 32 characters for a volume label and
allow special characters

6. Click on the Destination tab, select which drives you would like to
operate on from the drive list.
7. Specify the number of rounds you would like to conduct. (For multiple
rounds: when the first round is finished you will be prompted to remove
completed drives and insert the new drives before pressing OK to
continue).
8. Press the Start button to start the format process. Check the Output
window for job status updates

NOTE: If Full Format is selected, the formatting process may

take a significant amount of time.

www.duplim.com 9
Using the USB Duplication Suite Software

Format Then Data Copy (FAT, FAT32, NTFS)

The Format Then Data Copy function allows you to perform both a format
and data copy in the same job process. All selected drives will be formatted
with the file system you selected. Once the format is complete, the data
copy process will start automatically.

There are three format options available in the USB Duplication Suite.
Format FAT, Format FAT32, and Format NTFS. Each option will format the
selected drives and if specified apply a volume label.

By default a quick format will be run. However if you wishes to perform a

full format, you must check the “Full Format” box after selecting one of the
three formats.

1. Start by selecting “Format Then Data Copy” from the drop down menu.

10 www.duplim.com
Using the USB Duplication Suite Software

Format Then Data Copy (FAT, FAT32, NTFS) - continued

2. A new window will appear. Here you must select one of the three
formats “Format FAT”, “Format FAT32”, or “Format NTFS” by
clicking on its associated radio button. Once the format selection has
been made, press OK.

3. If a Full format is desired, check the box labeled Full Format to the
right of the drop down menu.
4. Because a data copy is involved in this job function, you may also
select the “Verify Data” check box.
5. Next, you may add any files or folders for copying, by clicking the
“Add File” or “Add Folder” buttons.
6. Next, click on the Destination tab.
7. Select the drives that you wish to format.
8. You can specify a volume label which will be applied to all drives in
the text box under “Enter Label” which is found in the Destination tab.
I. Note: FAT and FAT32 file systems have restrictions on volume
labels which allow for up to 11 characters, not including the following
special characters * ? . , ; : / \ | + = < > [ ]
II. NTFS file systems allow up to 32 characters for a volume label and
allow special characters
9. Click on the Destination tab, select which drives you would like to
operate on from the drive list.

www.duplim.com 11
Using the USB Duplication Suite Software

Format Then Data Copy (FAT, FAT32, NTFS) - continued

10. Specify the number of rounds you would like to conduct. (For multiple
rounds: when the first round is finished you will be prompted to remove
completed drives and insert the new drives before pressing OK to
continue).
11. Press the Start button to start the format and data copy process. Check the
Output window for job status updates.

NOTE: If Full Format is selected, the formatting process may take a

significant amount of time.

12 www.duplim.com
Using the USB Duplication Suite Software

Port Training
The port training function allows you to map each USB port on their duplicator
to a virtual port in the USB Duplication Suite. This acts as a visible aide when
identifying which drives shall be operated on.

1. From the drop down menu located in the source tab, select “Port Training”.
2. A new window will appear, at this time you must remove all USB drives
from the computer and then press “OK”.
3. The window should display “Insert USB flash drive into port 1”. Find port
one on the duplicator.
4. Using a single USB flash drive, insert the drive into port one of the
duplicator. Wait for the Port # learned dialogue to appear then Remove the
USB flash drive from the duplicator.
5. Repeat the process for each port on the duplicator

www.duplim.com 13
Using the USB Duplication Suite Software

Port Training - continued

6. Once each port has been trained, press the “Complete” button located on
the Port Training window.
Now, when a USB flash drive is inserted into the duplicator it will be
labeled with the mapped USB port instead of its Windows assigned
drive letter. For example, if the ports have been trained properly, when
a USB flash drive is plugged into port 3 of the duplicator, it should read
“USB-03” in the drive list located in the destination tab.

14 www.duplim.com
Technical Support

After reading this Software User Guide, if you need additional assistance,
please contact DupliM Technical Support. Our technical staff will be happy
to assist you, but they may need your help to better assist you. Calling
DupliM Technical Support without all the necessary information can be
both time consuming and frustrating. Therefore, please try to have your
questions about the DupliM USB Duplicator software ready before calling.
Please provide enough information about your problems so our technical
staff can recreate and diagnose it.

Technical Support Addresses and Phone Numbers

X By e-mail: [email protected]
X By Telephone: +1-818-678-0484
Technical Support Group can be reached 8:00 AM to 5:00 PM, Pacific
Time, Monday through Friday, excluding U.S. holidays.

Please try to call from a phone near your computer system.

X Access is available 24 hours a day, 365 days a year, via:

The World Wide Web at: www.DupliM.com

www.duplim.com 15
 Notes

16 www.duplim.com
Document Number: Master_USB_SUG_ENG_Rev. A Copyright © 2022
Specifications subject to change without notice.

DupliM Inc.
21722 Lassen Street
Chatsworth, CA 91311 U.S.A.

www.duplim.com