0% found this document useful (0 votes)

194 views51 pages

Technical Specification of 315 2500 KVA Distribution Transformer - PDF 01.06.17

This document outlines the technical specifications for outdoor type oil immersed three-phase distribution transformers ranging from 315 KVA to 2500 KVA, suitable for various voltage levels (11/0.433 KV, 22/0.433 KV, 33/0.433 KV). It covers aspects such as design, manufacturing, testing, and service conditions, ensuring compliance with relevant Indian and international standards. The specifications include detailed requirements for components, efficiency, insulation, and environmental considerations to ensure reliable operation in tropical climates.

Uploaded by

18 RIJUL SANKHYAN

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

194 views51 pages

Technical Specification of 315 2500 KVA Distribution Transformer - PDF 01.06.17

Uploaded by

18 RIJUL SANKHYAN

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 51

TECHNICAL SPECIFICATION OF 315KVA, 630 KVA, 1000 KVA, 1250KVA, 1600KVA,

2000KVA & 2500 KVA, 11/0.433 KV, 22/0.433 KV, 33/0.433 KV, Star-1, Star-2, Star-3, Star-
4 & Star-5, THREE PHASE, DISTRIBUTION TRANSFORMERS OUTDOOR TYPE OIL IMMERSED
WITHOUT CSP FEATURE.

Maharashtra State Electricity Distribution Company

Limited

MATERIAL SPECIFICATIONS CELL

TECHNICAL SPECIFICATION

FOR

TECHNICAL SPECIFICATION OF 315KVA, 630 KVA, 1000

KVA, 1250KVA, 1600KVA, 2000KVA & 2500 KVA, 11/0.433
KV, 22/0.433 KV, 33/0.433 KV, Star-1, Star-2, Star-3, Star-
4 & Star-5, THREE PHASE, DISTRIBUTION TRANSFORMERS
OUTDOOR TYPE OIL IMMERSED WITHOUT CSP FEATURE.

TECHNICAL SPECIFICATION NO.

CE/MMC/MSC-II/3Phase/DT/T/2017/03,

Amended on Date: 12.05.2017

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 1

TECHNICAL SPECIFICATION OF 315KVA, 630 KVA, 1000 KVA, 1250KVA, 1600KVA,
2000KVA & 2500 KVA, 11/0.433 KV, 22/0.433 KV, 33/0.433 KV, Star-1, Star-2, Star-3, Star-
4 & Star-5, THREE PHASE, DISTRIBUTION TRANSFORMERS OUTDOOR TYPE OIL IMMERSED
WITHOUT CSP FEATURE.

INDEX
Clause No. Contents
1 Scope
2 System Particulars
3 Service Condition
4 Applicable Standards
5 Specific Technical requirement
6 Design & Construction
6.1 Core
6.2 Windings
6.3 Losses
6.4 Insulation Material & Clearances
6.5 Impedance Value
6.6 Tank
6.7 Off Load Taps
7 Efficiency
8 Heat Dissipation
9 Total minimum oil volume
10 Conservator.
11 Breathers.
12 Terminals
13 Bushing and connections
14 Internal Connections
15 Tank base channel
16 Terminal Marking Plate & Rating Plate
17.1 Fittings
17.2 Fasteners
18 Lightning Arrestor
19 Transformer Oil
20 Tests & Inspection
21 Challenge Testing

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 2

22 Type Tests
23 Drawings
24 Rejection
25 Cleaning & Painting
26 Guaranteed Technical Particulars
27 Testing facilities
28 Submission of Routine Test Certificate
29 Stage Inspection
Testing of all distribution transformers for losses at 50 %
30
load and 100 % load
31 Random Sample Testing
32 Inspection & Testing of Transformer Oil
33 Quality Assurance
34 Qualifying Requirements
35 Final Inspection
36 Performance Guarantee
37 Cost Data Sheet
38 Schedule
Schedule A Guaranteed and Other Technical Particulars
Schedule B Tenderer‘s experience
Annexure-I Air Pressure Test
Annexure-II Unbalance Current Test
Annexure-III Temperature Rise Test

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 3

MAHARASHTRA STATE ELECTRICITY DISTRIBUTION COMPANY

TECHNICAL SPECIFICATION FOR 315 kVA & above and upto 2500 kVA,
11/0.433 , 22/ 0.433 & 33 /0.433 kV, Star-1, Star-2, Star-3, Star-4 & Star-5, THREE
PHASE, DISTRIBUTION TRANSFORMERS WITHOUT CSP FEATUTRE.

CE/MMC/MSC-II/3Phase/DT/T/2017/03 (Rev.)
1 Scope:-
1.1 This specification covers design, manufacturing, testing and delivery of 315 kVA &
above and upto 2500 kVA, 11/0.433 , 22/ 0.433 kV & 33/0.433 kV, Star-1, Star-
2, Star-3, Star-4 & Star-5, three phase distribution transformers without CSP
feature oil immersed, Oil Natural (ONAN) suitable for 11 kV, 22 kV & 33 kV,
50 Hz, Distribution system.
1.2 The equipment offered shall be complete with all parts necessary for their effective
and trouble-free operation. Such parts will be deemed to be within the scope of the
supply irrespective of whether they are specifically indicated in the commercial
order or not.
1.3 It is not the intent to specify herein complete details of design and construction. The
equipment offered shall conform to the relevant standards and be of high quality,
sturdy, robust and of good design and workmanship complete in all respects and
capable to perform continuous and satisfactory operations in the actual service
conditions at site and shall have sufficiently long life in service as per statutory
requirements.
1.4 The design and constructional aspects of materials shall not withstanding any
anomalies, discrepancies, omissions, in-completeness, etc. in these specifications
and will be subject to good engineering practice in conformity with the required
quality of the product, and to such tolerances, allowances and requirements for
clearances etc. as are necessary by virtue of various stipulations in that respect in
the relevant Indian Standards, IEC standards, I.E. Rules, I.E. Act and other
statutory provisions.
1.5 The Bidder/supplier shall bind himself to abide by these considerations to the entire
satisfaction of the purchaser and will be required to adjust such details at no extra
cost to the purchaser over and above the tendered rates and prices.
1.6 Tolerances:
The tolerance of guaranteed performance figures shall be as specified in the (Part-I)
table 1 of latest issue of IS 2026 except losses or relevant International Standard
except wherever specified otherwise in this specification.
2 System Particulars:-
The transformers shall be suitable for outdoor installation with following system
particulars and they should be suitable for service under fluctuations in supply
voltage as permissible under Indian Electricity Rules

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 4

2.1 Nominal System Voltage : 11 kV or 22 kV or 33 kV

2.2 Corresponding Highest System Voltage : 12 kV or 24 kV or 36 kV
2.3 Rated Basic Insulation Level : 75 KVp or 125 KVp or 170 KVp
2.4 Neutral earthing : Solidly earthed
2.5 Frequency : 50 Hz with ±3 % tolerance
2.6 Number of Phases : 3
3 SERVICE CONDITIONS:
3.1 Equipment supplied against the specification shall be suitable for satisfactory
operation under the following tropical conditions:-
i Max. ambient air temperature : 50 Deg. C
ii Max. relative humidity : 100 %
iii Max. annual rainfall : 1450 mm
iv Max. wind pressure : 150 kg/sq.m.
v Max. altitude above mean sea level : 1000 mtrs.
vi Isoceraunic level : 50
vii Seismic level(Horizontal acceleration) : 0.3 g.
viii Climatic Condition Moderately hot and
humid tropical climate
conducive to rust and
fungus growth.
ix Reference Ambient Temperature for
temperature rise : 50 Deg C
3.2 The climatic conditions are prone to wide variations in ambient conditions and
hence the equipment shall be of suitable design to work satisfactorily under these
conditions.

3.3 The equipment shall be for use in moderately hot and humid tropical climate
conducive to rust and fungus growth.
3.4 The Distribution Transformer shall be mark with standard mark governed by BIS as
per clause 13.4 of IS 1180(Part 1):2014] .
3.5 The Distribution Transformer shall bear Star 1 or 2 or 3 or 4 or 5 ratings label
approved by BEE ( Bureau of Energy Efficiency).
3.6 The Distribution Transformer shall bear level 2 (star 1 of BEE) or level 3 (star 2 of
BEE) ratings label approved by BIS (Bureau of Indian Standard) as per IS 1180
(Part-1):2014.

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 5

3.7 The Bidder/ Manufacturer shall possess the BIS license for offered product.

4 APPLICABLE STANDARDS:-

4.1 The design, manufacture and performance of the equipment shall comply with all
currently applicable statutes, regulations and safety codes. Nothing in this
specification shall be construed to relieve the bidder off his responsibilities.
4.2 The Distribution Transformers shall conform to IS: 1180 (Part 1) : 2014 amended
up to date or other International Standards for equal or better performance. Unless
otherwise modified in this specification the Distribution Transformers shall comply
with the Indian Standard Specification IS 1180 latest.
4.3 Unless otherwise specified, the equipment offered shall conform to amended up to
date Indian, IEC, British or U.S.A. Standards and in particular, to the following:-
4.4 The applicable standards are as follows :
Sr.No. IS number IS name

1. IS:1180(Part-1) : 2014 Outdoor type oil immersed distribution

transformers up to and including 2500 kVA,
33KV.
2. IS:2026(Part I to IV) Specification for power transformer
3. IS:335/1993 New insulating oil- Specification (fourth
revision)
4. IS:2099/1986, IS: 7421-1988, IS:3347 (Part-I Bushing
/Sec-2)-1979, IS:3347 (Part-I /Sec-1)-1982
amended up to date
5. IS 5 Colours for ready mixed paints and enamels.
6. IS 13730 (Part-27)1996 Specification for particular types of winding
wires.
7. IS: 3073/1974, IS: 3070( Part-II) Specifications for L.A‘s
8. CEA Guidelines August -2008 Manual on transformers
4.5 In case of conflict arising out due to variations between the applicable standard and
the standards specified herein the provisions of this specification should prevail.
5 Specific Technical requirement:
5.1 Standard kVA Ratings:-
The standard ratings for transformer shall be 315 kVA & above and upto 2500 kVA
as per IS 1180 (Part-I):2014
5.2 Nominal voltage ratings
i Primary voltage : 11 kV/ 22 kV/33 kV
ii Secondary voltage : 0.433 kV

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 6

5.2.1 Winding connections:-

i. H.V. Winding : Delta (∆)
ii. L.V. Winding : Star (Y)
so as to produce a positive phase displacement of 30 degrees from the primary to
the secondary vectors of the same phase. The neutral of the L.V. winding shall be
brought out to a separate insulated terminal. The voltage group shall be Dyn-11 (IS
2026 Part I).
5.3 Temperature Rise:
i The temperature rise for top oil over an ambient temperature of 50° C should be
40°C maximum [measured by thermometer in accordance with IS 1180 (Part 1)
& IS 2026 (Part 2)]
ii Temperature rise for winding over an ambient temperature of 50° C should
be 45° C maximum [measured by resistance method in accordance with IS
1180 (Part 1) IS 2026 (Part 2)]

5.4 No load voltage ratio:-

The no load voltage ratio shall be 11000/433 Volts, 22000/433 Volts & 33000/433
Volts.
6 Design & construction
a. The spring washers must be used for fixing core with tie rod.
b. Core base & bottom Yoke shall be supported with 75 mm X 40 mm X6 mm MS
Channel with proper bolting. The core assembly shall be fixed by four locking
bolts.
c. The maximum flux density in any part of the core and yoke at rated voltage and
frequency shall be such that the flux density with +12.5 % combined voltage
and frequency variation with rated voltage and frequency does not exceed 1.9
Tesla. Flux density should not be more than 1.55 Tesla at rated voltage and
frequency.
d. Limit of no load current shall be 2% of full load current of respective winding at
rated voltage.

6.1 Core
i The core shall be stacked/ wound type.
a) For Stack core :- The core shall be of high grade cold rolled grain
oriented (C.R.G.O) annealed steel lamination having low loss and good
grain properties, coated with hot oil proof insulation, bolted together to
the frames firmly to prevent vibration or noise. All core clamping bolts
shall be effectively insulated. The complete design of core must ensure

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 7

permanency of the core losses with continuous working of the

transformers.

b) For Wound core :-

The core shall be ‗C‘ type construction of high grade cold rolled grain
oriented (C.R.G.O.) annealed steel lamination having low loss and good
grain properties, coated hot oil proof insulation. The complete design of core
must ensure permanency of the core losses with continuous working of the
transformers. The core material shall not be brittle in case of CRGO
material.

Core clamping for C.R.G.O. Wound core type transformers shall be as

follows:

1. Core clamping shall be with top and bottom U- shaped core clamps
made of sheet steel clamped.

2. M.S. core clamps shall be painted with oil-resistant paint.

3. Suitable provision shall be made in the bottom core clamp / bottom plate
of the transformer to arrest movement of the active part.
4. Core shall be clamped by 16 mm diameter MS Tie rods.
ii The grade of core laminations shall be M4 or better.
iii The successful bidder, shall be required to submit the manufacturer‘s test
report showing the Watt Loss per kg and the thickness of the core
lamination, to ascertain the quality of Core materials.
The purchaser reserves the right to get sample of the core material tested at
any Government recognized laboratory.
iv The transformer core shall not be saturated for any value of V/f ratio to the
extent of 112.5% of the rated value of V/f ratio (i.e. 11000/50 or 22000/50)
(due to combined effect of voltage and frequency) up to 12.5% without
injurious heating at full load conditions and will not get saturated. The
bidder shall furnish necessary design data in support of this situation.
v Flux density:-
The maximum flux density in any part of the core and yoke at rated voltage
and frequency shall be such that the flux density with +12.5 % combined
voltage and frequency variation with rated voltage and frequency does not
exceed 1.9 Tesla. Flux density should not be more than 1.55 Tesla at rated
voltage and frequency.

vi The No load current at rated voltage shall not exceed the percentage as given
below.

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 8

The no load current of 315 kVA & above and upto 2500 kVA transformer
shall not exceed 2% the full load current and will be measured by energizing
the transformer at rated voltage and frequency. Increase of 12.5 percent of
rated voltage shall not increase the no load current by 5% of full load
current.( As per IS 1180 (Part1):2014)
Number of steps of core shall be minimum of
Sr. No. Rating (kVA) Number of steps
1 315 Min. 7 standard steps
2 630 Min. 9 standard steps
3 1000 Min. 9 standard steps
4 1250 Min. 11 standard steps
5 1600 Min. 11 standard steps
6 2000 Min. 13 standard steps
7 2500 Min. 13 standard steps

vii. Core clamping:

a. M.S channel for clamping core shall be 150 mm x 75 mm for 750 kVA
to 1250 kV and 200 X 75 mm from 1600 kVA to 2500 kVA
transformers.
b. M.S. Core base support channel shall be 100 mm x 50 mm.
c. 16 mm (min) dia, 2 nos High Tensile Bolts for 750,1000, 1250, 1600,
2000 & 2500 kVA in parallel at each end will be used.
d. The top yoke channels to be reinforced by adequate size of M.S. flat with
thickness not less than 8 mm, at equidistance if holes cutting are one for
LT lead so as to avoid bending of channel.
e. M S channels are to be painted by heat resistant paint.
f. Core clamping shall be with top and bottom U- shaped core clamps made
of sheet steel clamped.
g. Suitable provision shall be made in the bottom core clamp / bottom plate
of the transformer to arrest movement of the active part.

viii Tie bolts:

a. 8 nos. of tie rods of 16 mm dia. high tensile steel in vertical formation.
b. All top and bottom yoke nut bolts, if any, shall be MS and painted with
heat and corrosion resistant paint before use.
c. Drawing of the building of core to be approved before start of work.
d. The base channels of the core shall not be cut channel.
6.2 Winding:-
The material for winding shall be Copper.

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 9

i Materials:- Double paper covered Copper conductor shall be used for HV

and LV winding for 11 kV , 22 kV & 33 kV with respective class.
ii Current Density:- Current density for HV and LV winding should not be
more than 2.8 Amp/sq. mm for Copper.
iii L.V. Neutral formation shall be at top.
6.3 Losses :
The total losses (no-load + load losses at 75 deg. Centigrade ) at 50% of rated load & total
losses at 100% of rated load shall not exceed the maximum total loss values indicated as
below:
( As per Gazette notification issued by Ministry Of Power on Dated 16.12.2016 the
respective losses capacity wise revised).
TABLE – 1

Rating Impedance Maximum total losses in watts up to 11 kV Class ( For ratings above 200 kVA)
( Percent)
Star 1 Star 2 Star 3 Star 4 Star 5

50% 100% 50% 100% 50% 100% 50% 100% 50% 100%
Load Load Load Load Load Load Load Load Load Load
315 4.50 1025 3100 955 2750 890 2440 829 2164 772 1920
630 4.50 1860 5300 1745 4850 1637 4438 1536 4061 1441 3717
1000 5.00 2790 7700 2620 7000 2460 6364 2310 5785 2170 5259
1250 5.00 3300 9200 3220 8400 3142 7670 3066 7003 2991 6394
1600 6.25 4200 11800 3970 11300 3753 10821 3547 10363 3353 9924
2000 6.25 5050 15000 4790 14100 4543 13254 4309 12459 4088 11711
2500 6.25 6150 18500 5900 17500 5660 16554 5430 15659 5209 14813

Note:- 1) For Transformer having voltage class above 11 kV and up to and

including 22 kV, the permissible total loss values shall not exceed by 5
percent of the maximum total loss values mentioned in above table.
( Ref Clause 7.8.1.1.2 of IS 1180: Part- I/2014)
2) For Transformer having voltage class above 22 kV and up to and
including 33 kV, the permissible total loss values shall not exceed
by7½ percent of the maximum total loss values mentioned in above
table. ( Ref Clause 7.8.1.1.3 of IS 1180: Part-I/2014)

Tolerances:
No positive tolerance shall be allowed on the maximum losses given in the above
table for both 50 % & 100 % loading values. In case the actual loss values exceed
the above guaranteed values, the transformers shall be rejected at the risk, cost
and responsibility of the supplier. The bidder should guarantee individual No load
losses without any positive tolerance.

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 10

The values guaranteed in G.T.P. for flux density, no load current at rated voltage,
no load current at 100 % & 112.5% of rated voltage and no load loss at rated
voltage shall be individually met.

The tolerance on electrical performance excluding losses shall be as given in IS

2026(Part 1).

6.4 Insulation material & clearances:

i Materials - Makes of Electrical grade insulating craft paper, Press Board,
Perma wood/ Haldi wood insulation shall be declared in GTP by the bidder.
The test reports for all properties as per relevant I.S. amended up to date
shall be submitted during inspection.
ii The electrical clearance between the winding and body of the tank (between
inside surface of the tank and outside edge of the windings) should not be
less than 30 mm and 40 mm for 11 kV and 22 kV class respectively.
iii Thickness of locking spacers and thickness of comb teeth between HV coils HV
Disc – Minimum 3 mm. (minimum)up to 1000 kVA and 10 mm (minimum)
above 1000 kVA Distribution transformers and minimum clearance
for cross over coil shall be 10 mm upto 1000 kVA and 12mm above 1000 kVA
Minimum external clearances of bushing terminals
11 kV 22 kV 33 kV
HV Ph to Ph 255 mm 330 mm 350 mm
Ph to E 140 mm 230 mm 320 mm
LV Ph-to-Ph 75 mm. 75 mm 75 mm
Ph to E 40 mm. 40 mm 40 mm

6.5 Impedance Value -

The percentage impedance at 75 º C. for different ratings shall be as per Table-1 above.
6.6 Tank
6.6.1 The transformer tank shall be made up of prime quality M.S. sheets of rectangular
shape. No other shape will be accepted. The transformer tank shall be of robust
construction. All joints of tank and fittings should be oil tight and no bulging shall
occur during service. The tank design shall be such that the core and windings can
be lifted freely. The tank plates shall be of such strength that the complete
transformer when filled with oil may be lifted bodily by means of the lifting lugs
provided. Tank inside shall be painted by varnish or oil resistant paint. Top cover
plate shall be slightly sloping; approximately 5 to 10 deg. towards HV bushing and
edges of cover plate should be bent downwards so as to avoid entry of water
through the cover plate gasket. The width of bend plate shall be 25 mm min. The

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 11

top cover shall have no cut at point of lifting lug. The rectangular tank shall be
fabricated by welding at corners.
6.6.2 The transformer tank of corrugation is also acceptable, however shape of tank shall
be rectangular only. The corrugation sheets thickness shall be of minimum 1.6 mm.
Corrugation panel shall be used for cooling. The transformer shall be capable of
giving continuous rated output without exceeding the specified temperature rise.
Bidder shall submit the detailed calculation sheet alongwith offer. The safe guard
angle frame 50X50X5 mm shall be welded for corrugated side to the tank.
6.6.3 In rectangular shape tanks, horizontal or vertical joints in tank side walls and its
bottom or top cover will be not allowed. In addition the cover of the main tank shall
be provided with an air release plug to enable air trapped within to be released.
Side wall thickness : 4 mm. (min.)
Top and bottom plate thickness : 6 mm. (min.) from 315 kVA to
1600 kVA
: 10 mm (min) from 2000 kVA &
2500 kVA

a)The pressure deflection, when tank without oil is subjected to a vaccum of 500 mm of
mercury for rectangular tank and 760 mm of mercury for round tank.
b)The permanent deflection shall be as below.
(All figures in mm)
Horizontal length of flat Plate Permanent deflection
Up to and including 750 mm 5.0 mm
751 to 1250 mm 6.5 mm
1251 to 1750 mm 8.0 mm
Above 1751 mm 9.0 mm

c)The tank shall further be capable of withstanding a pressure of 0.8 kg/sq.cm and
vaccum of 0.7 kg/sq.cm(g) without any deformation.
d)The height of the tank shall be such that minimum vertical clearance up to the top
cover plate of 120 mm is achieved from top yoke / from the top of tap changer if tap
is provided.
6.6.4 Reinforced by welded angle 50X75X5 MM upto 1250 kVA & 70X75X5 MM upto
2500 kVA on all the outside walls on the edge of tank to form two equal
compartments
6.6.5 When transformer tank without oil is subject to air pressure of 35 KPa above
atmospheric pressure for 30 min. Pressure test shall be performed carefully at the

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 12

time of 1st stage inspection only to confirm the adequacy of reinforcement angle and
gauge of the tank and certified by E.E. (IW).
6.6.6 All welding operations to be carried out by MIG process.( Metal Inert Gas Welding)
6.6.7 Lifting lugs: 4 nos. welded heavy duty lifting lugs of MS plate of 12mm thickness
upto 1600 kVA & 16 mm thickness upto 2500 kVA , suitably reinforced by vertical
supporting flat of same thickness as of lug welded edgewise below the lug on the
side wall, up to reinforcing angle and for top cover 8 mm thickness upto 1600 kVA
and 10 mm thickness upto 2500 kVA. They shall be so extended that cutting of
bend plate is not required.
6.6.8 Pulling lugs: 4 nos. of welded heavy duty pulling lugs of MS plate of 8mm & 10
mm thickness for upto 1600 kVA & 2500 kVA respectively, shall be provided to
pull the transformer horizontally.
6.6.9 All bolts / nuts / washers exposed to atmosphere shall be as follows:
a) Size 12mm or below—stainless steel.
b) Above 12mm--- steel with suitable finish like electro galvanized with
passivation or hot dip galvanized.
6.6.10 Top cover fixing bolts: GI nut bolts of 1/2‖ diameter with one plain washer shall be
used for top cover fixing, spaced at 4‖ apart. 6 mm neoprene bonded cork oil
resistance gaskets conforming to type B/C IS 4253 Part-II amended up to date will
be placed between tank and cover plate.
6.6.11 Vertical clearance: - The height of the tank shall be such that minimum vertical
clearance up to the top cover plate of 120 mm is achieved from top yoke.
6.6.12 The transformer tank shall be of adequate mechanical strength to withstand positive
and negative pressures built up inside the tank while the transformer is in operation.
6.6.13 The tank design shall be such that the core and windings can be lifted freely.
6.6.14 Plain tank shall be capable of withstanding a pressure of 80kPa for 30 minutes and a
vacuum of 500 mm of mercury for 30 minutes (Type Test). The permanent
deflection of flat plates shall not exceed the values given in IS 1180(Part 1): 2014
clause no. 21.5.2.1.
6.6.15 All bolts /nuts /washers exposed to atmosphere shall be as follows:-
a) Size 12 MM or below – Stainless steel
b) Size above 12 MM – steel with suitable finish like electro galvanised with
passivation.
6.6.16 Thermometer pocket must be located at centre of top cover or high side of tank
height for true valve of max top oil temperature
6.6.17 Air release plug must be placed at top cover of explosion vent pipe, testing at
lkg/sq.cm carried out on sample at first lot to know correct material used for
diaphragm and it must burst before pre determined pressure.

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 13

6.7 Off Load Taps:

6.7.1 The standard tapping ranges, when taps are provided, shall be as follows:
Winding tapped : HV
Number of tap positions :7
Voltage variations : (+) 5 percent to (-) 10 percent in steps of 2.5 percent
for variation of HV Voltage (As per IS 1180
(Part1):2014 Clause 7.7.1).
6.7.2 For rating 500 kVA and above on load tap changers may be provided for variation
of HV voltage from (+) 5% to (-)15 % in steps of 2.5 %.(As per IS1180 ( Part1):2014
Clause 7.7.3)
OR
Provision of any other tapping range and tapping step is subject to agreement between
the user and the supplier .(Amendment no.1 to IS1180 ( Part1):2014)
Note: The standard tapping range and tapping steps arrangement shall not be required
up to 630 KVA capacity, when Distribution Transformers are procured by MSEDCL for
any on going scheme.

6.7.3 Tapping Method: Off circuit tap-changing arrangement shall be either by means of
links or by means of an externally-operated switch with mechanical locking device
and a position indicator. Arrangement for pad-locking shall be provided. ( As per IS
1180 (Part1):2014 Clause 7.7.2)

Tap changing shall be carried out by means of an externally operated

self position switch and when the transformer is in de-energised condition switch
position No.1 shall correspond to the maximum plus tapping. Each tap change shall
result in variation of 2.5 % in voltage. Provision shall be made for locking the
taping switch handle in position. Suitable aluminium anodized plate shall be fixed
for tap changing switch to know the position number of tap.

6.7.4 The Transformer shall be capable of being operated without danger on any tapping at
the rated kVA with voltage variation ± 10% corresponding to the voltage of that
tapping.

7.0 Efficiency:
The efficiency is the ratio of output in KW to the input in KW.

Efficiency = (Input in KW – Total Losses in KW)

Input in KW

The minimum Percentage Efficiency of distribution transformer shall

be 98.25 %. Total loss comprise of No-load loss and Load loss.

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 14

8.0 Heat Dissipation:

a) Heat dissipation calculation should be based on minimum measured total loss

( No load at rated excitation + load loss at 100 %loading maximum current tap
converted to 75 deg' C reference temperature) shall be supplied during
temperature rise test.(if tapping provided at the lowest tap).
b) The heat dissipation by tank wall should be increase to appropriate value
considering the climatic temperature rise.

9.0 Total Minimum Oil Volume :

The firm should maintain the minimum oil volume in all supplied transformers
as mentioned below or oil up to mark indicator level whichever is more.

Sr.No. KVA Oil in liters (exclusive of oil absorbed in core & coil
rating assembly)
Voltage rating Voltage rating Voltage rating
11/0.433 kV 22/0.433 kV 33/0.433 kV
1 315 500 550 580
2 630 750 800 840
3 1000 850 900 950
4 1250 1000 1050 1100
5 1600 1300 1350 1400
6 2000 1550 1600 1650
7 2500 1900 1950 2000

10.0 Conservator:
a) The total volume of conservator shall be such as to contain 10% of total quantity of
oil. Normally 3% quantity of the total oil will be contained in the conservator.
Dimension of the conservator shall be indicated on the General Arrangement
Drawing. The capacity of the conservator tank shall be designed keeping in view
the total quantity of oil and its contraction and expansion due to the temperature
variations.
b) Oil level indicator shall be provided on the side which will be with fully covered
detachable flange with single gasket and tightened with MS nut-bolt. Level
indication by colour shall not be accepted.
c) The inside diameter of the pipe connecting the conservator to the main tank shall be
within 20 to 32 mm and it should be project into the conservator in such way that its

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 15

end is approximately 20 mm above the total of the conservator so as to create a

sump for collection of impurities. The minimum oil level (corresponding to (-) 5
deg.) should be above the sump level & filling hole (32mm dia) with cover.
d) There shall be minimum -5deg, normal 30deg and maximum 98deg marking on the
oil gauge indicator of the conservator.
e) Buchholz Relay:- Above 1 MVA transformer as per Clause 20.1 V of IS 1180 is
necessary.
11.0 Breather:
a) The material used for breather shall be only of Poly propylene
b) The dehydrating agent shall be silica gel. The volume of breather shall be
suitable for 1kg silica gel confirming to IS 3401 up to 1MVA and 2 kg for more
than 1 MVA.
Makes of the breather shall be subject to purchaser's approval. The make and
design of breather shall be subject to approval of C.E. (MMC).
12.0 Terminals:
a. The Palm type terminal connector of adequate capacity shall be connected to L.V
side suitable to connect it to the Bus extension.
b. On H.V. side the bimetallic connector to be provided with bimetallic lug of suitable
rating.
c. The rating of brass rod & copper rod for H.V. & L.V. shall be as per relevant IS
for different capacity of Transformer. [Following (d) and (e) are indicative and shall
be confirmed with relevant IS)]
d. Brass rods 12 mm. diameter for HT with necessary nuts, check-nuts and plain thick
tinned washer.
e. Tinned Copper Rods of 20 & 30 mm diameter for 315&630 kVA, 42 mm diameter
for 1000 kVA & 1250kVA, 48 mm diameter upto 1600 kVA and 55 mm diameter
above 1600 kVA distribution transformers for LT extension with suitable cable
lugs, necessary nuts, check-nuts and plain thick tinned washer.

13.0. Bushings & Connections:

13.1 The transformers shall be fitted on high voltage and low voltage sides with outdoor
type bushings of appropriate voltage and current ratings. The high voltage bushings
(3nos.) shall be provided with R-Y-B colour coding marking & shall conform to IS
2099. The low voltage bushings (4 nos.) shall conform to IS 7421. Alternatively, the
low voltage side may be made suitable for adoption of PVC/XLPE cables of
suitable size. The dimensions shall conform to IS 1180(Part 1): 2014 clause no.
10.1.5.

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 16

13.2 The bushing shall be made in two parts. The outer bushing shall be of porcelain.
The dimensions of the outer bushing shall confirm to the relevant Part/Section of IS
3347 depending on the voltage class. The internal bushing shall be of either
porcelain or tough insulating material, like epoxy and shall have embedded stem.
Metal portion of the internal HV and LV bushing inside the tank shall remain
dipped in oil in all operating conditions.
13.3 Gaskets shall be made of synthetic rubber or synthetic rubberized cork resistant to
hot transformer oil.
13.4 For 11 kV class 12 kV bushing, for 22 kV class 24 kV & 33 kV class 36 kV bushing
shall be used and for 433 volts 1.0 kV bushing shall be used. Bushings of the same
voltage class shall be interchangeable. Bushings with plain shed shall be as per relevant
IS:3347 amended up to date. HV bushings shall be mounted on the top of the
transformer tank & LV bushings shall be mounted on side of the transformer tank.
13.5 HV bushings shall be mounted on curvature shaped embossed plate and not on welded
M.S ring. Supporting clamps for LT cable should be provided to avoid the weight of
cable on the Bushing.
13.6 The minimum creepage distance for both HV & LV Bushings shall not be less than 25
mm per kV.

14.0 Internal connections:

14.1 H.V. Winding :
i. Leads should be taken through Bakelite tubes.
ii. Inter coil spacers between HV sections by dovetailed paper block min.8mm
to avoid displacement of coil during transportation.
iii. The copper strip/foil used for core earthing at two locations shall be tinned
copper.
iv .In case of H.V. winding all jumpers from winding to bushing shall have
cross section larger than winding conductor.
v. Inter coil connection shall be by crimping and brazing.
vi.In case of Copper Winding Delta joints shall be with crimping and Brazing
only.
vii. Lead from delta joint shall be connected to bushing rod by brazing only.
14.2 L.V. Winding :
i. For Copper windings crimping & silver brazing alloy shall be used.
ii. L.T. Star point shall be formed of Copper flat of sufficient length. Lead from
winding shall be connected to the flat by crimping and brazing.
iii. Firm connections of L.T. winding to bushing shall be made of adequate size of
`L' shaped flat. Connection of L.T. Coil lead to `L' shape flat shall be by

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 17

crimping and brazing. Alternatively `L' shape lug of adequate capacity

effectively crimped shall be acceptable.
iv. `L' shape flat/lug shall be clamped to L.V. Bushing metal part by using nut,
lock-nut and washers.
15.0 Tank base channel / Mounting Arrangement :
The under-base of the transformer shall be provided as per clause 14.2 of IS
1180(Part1):2014
16.0 Terminal Marking Plates and Rating Plates :
a) All Transformer HV terminals shall be provided terminal marking plated to Tank.
Each terminal, including with neutral, shall be distinctly marked on both primary &
secondary in accordance with the connection diagram fixed upon the transformer
which shall conformed to latest 1S-2026 (part- IV).
b) Each Transformer shall be provided with rating plate having marking as per IS 1180
(part-l):2014 clause no 13 clearly indicating max. total losses at 50% rated load in
watts and maximum total losses at 100% rated load in watts
c) Rating & terminal marking plates shall be combined into one plate and shall be mark
with standard mark Govern by the provisions of the BIS act 1986.
d) Terminals shall be provided with terminal marking plates. The transformer shall be
provided with riveted rating plate of minimum 18 SWG aluminum anodized
material sheet in a visible position. The entries of the rating plate shall be in
indelibly marked (i.e. by etching, engraving or stamping).
e) Marking as `M.S.E.D.C.L'S and `Sr. No.' of transformer shall be engraved on
transformer main tank below L.T. bushings.
f) The name of the company, order No., capacity, month and year of manufacturing
shall be engraved on separate plate which shall be firmly welded to main tank and
shall form integral part of the tank.
g) The distribution transformer may also be marked with the Standard Mark. The use
of Standard Mark is governed by the provisions of the Bureau of Indian Standards
Act, 1986 and the Rules Regulations made thereunder.
Besides other particulars, following details shall also be given on the name plate.

 ISI Mark.
 BEE Energy Efficiency Star label
 BIS Energy Efficiency level.
 Order No. – Month & year.
 Sr. No. of transformer.
 Date of manufacturing – Month & year.

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 18

 Date of expiry of guarantee period – month & year.

 Maximum guaranteed 50% load loss & 100 % load loss figures.
 Name and full address of the manufacturer.
 Capacity.
 Rating.
(All details on the rating and diagram plate shall be indeligibly
marked i.e. by engraving or stamping or etching).

17.1 Fittings:

The following standard fittings shall be provided.

1 Rating and diagram plate 1 no.
2 Earthing terminals with lugs. 2 nos.
3 Lifting lugs 6 nos. ( 4 nos for tank and 2 nos for
top plate of the transformer )
4 Oil filling hole with cap (on conservator) 1 no
5 Drain valve – 32mm for all T/Fs ( It shall 1 no
be covered with metallic box spot welded
to tank) IS554
6 Conservator with drain plug. 1 no
7 The pipe connecting the conservator to 1 no
the main tank.
8 Thermometer pocket with cap 1 no
9 Air release device. 1 no
10 Explosion vent with diaphragm 1 no
11 Silica gel breather 1kg /2 kg 1 no
12 Platform mounting channel ( with hole 2 nos
suitable for axle of rollers)
13 Oil level gauge indicating 3 positions of 1no
oil marked as below :
Minimum (-) 5 deg.C.
Normal 30 deg.C
Maximum 98 deg.C.
14 HT & LT bushing and terminal 3 nos. of HT bushing and 4 nos. of
connectors LT bushing shall be provided with 3

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 19

nos. of brass nuts and 2 plain brass

washers.
15 Radiators As per Cl. No. 8 (b)
16 Lightening Arrestors for HT bushings 3 nos
17 Pulling lugs 4 nos
18. Rollers 4 nos
19. Five year guarantee plate 1 no.
20 Filter valve ( 32 mm dia) 1 no.
21 Anti-theft stainless steel fastners with 4 nos.
breakaway nut at top cover
22 Jacking pad for transformer above 1 Set
1600KVA.
23 Magnetic oil level guage with low oil 1 no.
level alarm contact for above
1600KVA transformer.

Any other fitting necessary for satisfactory performance.

17.2 Fasterners.
 All bolts, studs, screw threads, pipe threads, bolt heads and nuts shall comply
with the appropriate Indian standards for metric threads or the technical
equivalent.
 Bolts or studs shall not be less than 6 mm in diameter except when used for
small wiring terminals.
 All nuts and pins shall be adequately locked.
 Wherever possible bolts shall be fitted in such a manner that in the event of
failure of locking resulting in the nuts working loose and falling off, the bolt
will remain in position.
 All ferrous bolts, nuts and washers placed in outdoor positions shall be treated
to prevent corrosion by hot dip galvanizing except high tensile steel bolts and
spring washers, which shall be Electro, galvanized. Appropriate precautions
shall be taken to prevent electrolytic action between dissimilar materials.
 Each bolt or stud shall project at least one thread but not more than three threads
through the nut, except when otherwise approved for terminal board studs or
relay stems. If bolts are provided at inaccessible places for ordinary spanners,
special spanners shall be provided.
 The length of screwed portion of the bolts shall be such that no screw thread
may form part of a sheer plane between members.
 Taper washers may be provided where necessary. Protective washers of suitable
material shall be provided front and back of the securing screws.
 LT side should be of Pad type terminal.

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 20

18.0 Lightening Arrestors:

The Lightening Arrestors (Disconnector type) of high surge capacity of

9 kV( Vrms), 5 kA( 8/20 micro wave shape) for 11 kV class transformers
and 18 kV( Vrms), 5 kA ( 8/20 micro wave shape) for 22 kV class transformers &
30 kV, 10 kA ( 8/20 micro wave shape) for 33 kV , conforming to IS: 3070/1993
shall be mounted on the HV bushings of transformer, clamped securely to the tank,
to protect the transformer and associated line equipment from the occasional high
voltage surges resulting from lighting or switching operations. The earthing
terminal of the lightening arresters shall be grounded separately.
Random sample of LA shall be destructively tested by breaking the LA to confirm
availability of inside component only.

19.0 Transformer Oil

Transformer oil to be used in all the Distribution transformers shall comply with the
requirements of latest IS 335/1983 amended up to date thereof. In addition the oil
should conform to `Ageing Characteristics‘ specified below for New Oil and Oil in
Transformers. Type test certificates of oil being used shall be produced to EE (IW)
at the time of stage inspection.

New oil - Ageing characteristics after accelerated ageing test 96 hrs at 115° C (open
beaker method with copper catalyst):

i. Specific Resistance (Resistivity)

a) at 20 º C :- 2.5 x 10 12 Ohm-Cm (Min)

b) at 90 º C :- 0.2 x 10 12 Ohm-Cm (Min)

ii. Dielectric dissipation factor - 0.20 (Max .tan delta) at 90 º C.

iv. Total sludge value (%) by weight - 0.05 (Max.)

v. The method of testing these aging characteristics is given in Appendix - C of

IS 335 amended up to date.
vi. The Density of oil shall be maximum 0.89 g / cm3 at 29.5 ° C as per IS
1448.
vii. Total acidity mg/KOH/gm-0.05(Max.)
viii. The important characteristics of the transformer oil after it is filled in the
transformer (within 3 months of filling) shall be as follows: -

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 21

Sr.No. Characteristics Specifications

1. Electric Strength (Breakdown voltage) 30 kV (Min)

2. Dielectric dissipation factor (Tan Delta) at 90 deg.C.) 0.01 (Max)

3. Specific Resistance (Resistivity) at 27 deg. C (ohm-cm) 10 x 10 12

4. Flash Point, P.M. (closed) 140 º C (Min)

5. Inter facial tension at 27 º C. 0.04N/M (Min)

6. Neutralization value (total acidity) 0.03Mg.KOH/gm (Max.)

7 Water content PPM 40 (Max)

20.0 Test and Inspection:- All routine, type and special tests as described in Clause
21.2 to 21.4 of IS 1180 (Part 1):2014 shall be performed as per relevant parts of
IS 2026. Pressure and oil leakage test shall be conducted as per Clause 21.5 of IS
1180 (Part1):2014.

20.1 Routine Tests (to be conducted on all units):- The following shall
constitute the routine tests:
a) Measurement of winding resistance [ IS 2026 (Part 1)].
b) Measurement of voltage ratio and check of phase displacement [ IS 2026 (Part
1)].
c) Measurement of short circuit impedance ( principal tapping, when applicable)
and load loss at 50 percent and 100 percent load [ IS 2026 (Part 1)].
d) Measurement of no load loss and current [ IS 2026 (Part 1)].
e) Measurement of insulation resistance [ IS 2026 (Part 1)].
f) Induced over-voltage withstand test [ IS 2026 (Part 3)].
g) Separate-source voltage withstand test [ IS 2026 (Part 3)].
h) Pressure test
i) Oil leakage test
20.2 Type Tests (to be conducted on one unit):- The following shall constitute
the type tests:
a) Lightening impulse test [ IS 2026 (Part 3)].
b) Temperature-rise test [ IS 2026 (Part 2)].
Note – Maximum measured total loss ( No load at rated excitation + load loss
at maximum current tap converted to 75 Deg.Celcius reference temperature) at
100 percent loading shall be supplied during temperature rise test.
c) Short-circuit withstand test [ IS 2026 (Part 5)]. ( above 200 kVA)

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 22

d) Pressure test.
In addition to that the successful bidder shall submit the type test report of
transformer Oil & HV/LV bushings as per relevant IS with offer.
20.3 Special Tests (to be conducted on one unit):- The following shall
constitute the special tests which shall be carried out by mutual agreement between
the user and the supplier.
a) Determination of sound levels [ IS 2026 (Part 10)].
b) Short-circuit withstand test [ IS 2026 (Part 5)]. ( above 200 kVA).
NOTE :- Routine tests before and after short circuit test shall be conducted as
per IS 2026 ( Part 1)
c) No load current 112.5 percent voltage [refer clause 7.9.2 of IS 1180(Part 1):
2014].
d) Paint adhesion tests: The test is performed as per ASTM D 3359 ( Standard
Test Methods for measuring adhesion by Tape Test).
e) BDV and moisture content of oil in the transformer ( IS 335).
Note:Tests at (d) and (e) may be carried out on more than one unit subject to
agreement between user and supplier.
20.4 Pressure and Oil leakage Test :-

20.4.1 Pressure Test ( Type Test) : For non-sealed and sealed type transformers,
the transformer tank subjected to air pressure of 80 kPa for 30 min and vacuum of
500 mm of mercury for 30 min. The permanent deflection of flat plate, after
pressure/vacuum has been released, shall not exceed the values given below.

Length of Plate Deflection

Up to 750 mm 5.0 mm

751 mm to 1250 mm 6.5 mm

1251 to 1750 mm 8.0 mm

Above 1751 mm 9.0 mm

20.4.2. Pressure Test ( Routine Test) :

a) Plain tanks : The transformer tank with welded / bolted cover shall be tested at
a pressure of 35 kPa above atmospheric pressure maintained inside the tank for 10
min. There should be no leakage at any point .

b) Corrugated tanks : The corrugated transformer tank shall be tested for air
pressure of 15 kPa above atmospheric pressure maintained inside the tank for 10
min. There should be no leakage at any point .

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 23

20.4.3 Oil leakage Test ( routine Test) : The assembled transformer for non-
sealed and sealed type with all fittings including bushing in position shall be
tested at a pressure equivalent to twice the normal head measured at the base of the
tank for 8 h. There should be no leakage at any point. Tank with corrugations shall
be tested for oil leakage test a pressure of 15 kPa measured at the top of the tank
for 6 h. There should be no leakage at any point.

All the routine tests shall be conducted in the suppliers' laboratory at their own
cost.

i) Heat run test shall be arranged free of cost on the unit selected from the 1 st
lot by Executive Engineer/Authorized Representative.

ii) The calculations to confirm the thermal ability IS or equivalent International

Standard shall be submitted to Executive Engineer (IW).
21.0 Challenge Testing:
The manufacturer can also request challenge testing for any test based on
specification and losses. The challenger would request for testing with testing fees.
The challenge test fees are proposed at least three times the cost of testing. This is
likely to deter unnecessary challenges. The challenger would have the opportunity to
select the sample from the store and any such challenge should be made with in the
guarantee period. The party challenged, challenger and the utility could witness the
challenge testing.
The challenge testing would cover following tests:
1. Measurement of magnetizing current.
2. No load losses test.
3. Load losses test (at 50 % loading or as per routine test).
4. Temperature rise test.
The challenge test could be conducted at NABL Laboratory, like ERDA and CPRI.
If the values are within the limits the products gets confirmed else not confirmed. No
positive tolerances in losses is permitted. If the product is not confirmed the
manufacturer would pay the challenge fee and challenger would get the fee refunded.
However as a redressal system the challenger would be allow to ask for fresh testing
of two or more samples from the store and the same be tested in NABL Laboratory
in presence of party challenge, challenger and the utility.
If any one of the above sample does not confirm the test, then the product is said to
have failed the test. In such cases the manufacturer will be declared as unsuccessful
manufacturer for the said product with wide publicity and would not allow to
complete in tenders of the MSEDCL for the period of three years and heavy penalty
would be imposed.
22.0 Type Tests
22.1 The Type Tests as per Clause 20.2 above shall be successfully carried out at
laboratories accredited by National Accreditation Board for Testing and Calibration

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 24

Laboratories (NABL) in accordance with IS 1180(Part 1):2014 as amended from

time to time and technical specifications, within the last 5 (five) years prior to the
date of offer.

22.2 The type test reports should be submitted and got approved from the Chief Engineer
(MMC) before commencement of supply.
22.3 In case of any of the following, the offer may be considered for
evaluation only.
i) If above tests are carried out beyond 5 years
ii) Impulse Voltage Withstand test ,Dynamic Short Circuit test,
Temperature rise Test & Pressure Test carried out not from
NABL approved Laboratory.
iii) If there is any change in the design/ type of old type tested
transformers to be offered against this specification.
Note: However, In that case successful bidders have to carry out the type tests at the
laboratories accredited by NABL before commencement of supply at their own
expense on the sample drawn by the purchaser from the lot offered for first Stage
Inspection.
22.4 In respect of the successful bidder, the purchaser reserves the right to demand
repetition of some or all the type tests in presence of the purchaser‘s representative.
In case the unit fails in the type tests, the complete supply shall be rejected. The
bidders are therefore requested to quote unit rates for carrying out each type test,
which however, will not be considered for evaluation of the offer.
23.0 Drawings & Calculation sheet:-
23.1 A set of following drawings with all dimensions shall be submitted by the Bidder
along with the offer:

i. General Dimensional drawing.

ii. Core Assembly drawing.

iii. Internal Construction Drawing

iv. Rating & Diagram Plate Drawing.

v. HV& LV Bushings Assembly drawing

vi. Creepage distances distance drawing of HV& LV Bushing

vii. Silica gel Breather drawing.

Viii Technical Detail drawing.

ix. Calculation sheet for flux density

x. Heat dissipation

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 25

xi. Oil absorption

xii. Thermal time constant.

23.2 The drawings shall be of A-3 (420 x 297 mm) size only. The bidder should also
supply along with his offer the pamphlets/literatures etc. for fittings / accessories.

23.3 The bidder should not change design once offered as per A/T, Approved drawings
and Type Test Reports.

23.4 The successful Bidders shall submit complete set of Drawings (as listed in
Cl.No.23.1) of transformer in triplicate indicating dimensions to CE (MMC) for
approval and get approved it before offering Ist stage inspection.
24.0 Rejection :-
24.1 Apart from rejection due to failure of the transformer to meet the specified test
requirements the transformer shall be liable for rejection on any one of the
following reasons.
i. Maximum load losses at 50 % load & 100% Load loss exceeds the specified
values mentioned in Cl. No.6.3 above.
ii. Impedance voltage value exceeds the Guaranteed value plus tolerances as
mentioned at Cl..No.6.5 above.
iii Type test are not carried out as per clause no. 22.0 of the specification.
iv. Drawings are not submitted as per clause no. 23.0 of the specification.
v. GTP not submitted as per clause no. 26.0 of the specification.
vi Heat dissipation calculation sheet are not submitted as per clause no.8.0 of the
specification.
25.0 Cleaning and Painting.
i. The external surfaces shall be painted with one coat of thermo setting powder
paint or one coat of epoxy primer followed by two coats of polyurethane (finish
coat)for (outside) and hot oil resistant paint/varnish with one coat (inside) with
dry film thickness as mentioned in Table 12, clause 15.5 of IS 1180(Part 1):2014.
ii. The certificate shall be produce by the manufacturer if seven tank facilities are
availed from the other vendor about availability of the adequate size of tank for
treatment.
iii.The test of measurement of paint thickness shall be carried out cross hatch test,
chemical test and other as per IS 13871:1993
iv. The surface of the tank shall be properly pre-treated / phosphated in a seven tank
process and shall be applied with a powder coating of 40 micron thickness. The
powder coating shall be of Aircraft Blue colour ( shade No. 108) for

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 26

transformers. Powder coating shall be suitable for outdoor use. The seven tank
process facility shall be enhance to ensure proper quality for outdoor application.
v. The month and year of supply shall be painted in red bold Marathi lettering at
two places, one on conservator and other at sum conspicuous place on the
transformer which shall be clearly visible from the ground.

26.0 Guaranteed & Technical Particulars:

The bidder should fill up all the details in GTP parameter list, the statement such as
―as per drawings enclosed‖, ―as per MSEDCL‘s requirement‖ ―as per IS‖ etc. shall
be considered as details are not furnished and such offers shall liable for rejection.
27.0 Testing facility
The bidder should have adequate testing facility for all routine and acceptance tests
and also arrangement for measurement of losses, resistance, etc. details of which
will be enumerated in the tender.
28.0 Submission Routine Test Certificate
a. The successful bidder shall submit the routine test certificate along with
documentary evidence for having paid the Excise Duty for the following raw
materials viz. Oil, Aluminum, copper for conductors, insulating materials, core
materials, bushings at the time of routine testing of the fully assembled transformer
b. Instruction and operation Manual
The successful bidder shall be required to submit 5 copies of instruction and
Operation manual for each lot of 100 Transformers (or part thereof) supplied. This
instruction manual should give complete details about the pre-commissioning
tests/checks and the details of preventive maintenance etc.

29.0 Stage Inspection :-

29.1 Supplier shall give 15 days‘ advance intimation to the Chief Engineer (MMC) and
S.E. (MM) to organize stage inspection in which assembly of core, windings and
other core materials etc. would be inspected. In respect of raw materials such as
core stamping, winding conductor, oil etc. successful bidder shall use these
materials manufactured/supplied by the standard manufacturers and furnish the
manufacturer's test certificates, as well as, proof of purchase from those
manufacturers documentary evidence for having paid the excise duty for the
information of the department.

29.2 Chief Engineer (MM Cell) will depute representatives from testing and inspection
wing at the time of Stage inspection.

29.3 10 % of the transformers from the offered lot will be tested for acceptance tests at
factory, in the presence of purchaser's representative before dispatch.
29.4 The inspection may be carried out by the purchaser at any stage of manufacture. The
successful bidder shall grant free access to the purchaser's representatives at a
reasonable time when the work is in progress. Inspection and acceptance of any

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 27

equipment under this specification by the purchaser shall not relieve the supplier of
his obligation of furnishing equipment in accordance with the specifications and
shall not prevent subsequent rejection if the equipment is found to be defective.
29.5 The purchaser may at its option, open a transformer supplied to the Stores, in
presence of supplier at site or at Stores. If any of the technical particulars are seen
to be in variance than the guaranteed technical particulars, the whole lot of
transformer will be rejected without any liability on purchaser.
29.6 In addition to the above, the purchaser may pick up any transformer and decide to
get it type tested from any laboratory accredited by NABL at purchaser's cost. The
Bidder will have to organize packing of the transformer at company's Stores for
which they will be paid necessary charges. If the transformer fails to meet the
requirement of type tests, the quantity of transformers ordered on them will be
forthwith rejected and the purchaser may purchase these transformers at the risk and
cost of the supplier.

30.0 Testing of all Distribution Transformers for losses at 50% load and 100% load:
After inspection of new transformers at factory for acceptance of the lot, all
distribution transformers from the lot will be tested for 50% load and 100% load at
all stores. Tenderer has liberty to be present at the time of testing.

31.0 Random Sample Testing (RST)

The tenderer should intimate to C.E. (MM Cell ), M.S.E.D.C.L of completion of
dispatches of whole lot of Distribution Transformers to stores against this tender.
C.E. (MM Cell), M.S.E.D.C.L for will select the stores for Random Sample Testing
(RST) and depute E.E. (Testing) to carry out RST of the lot.
E.E. (Testing) will select a transformer from the lot of transformers already tested
for 50 % load and 100 % load.15 days advance intimation will be given to tenderer
for joint inspection. The date of RST will not be altered to the convenience or
request of supplier. If supplier‘s representative fails to attend on the date fixed for
RST, the RST will be carried out in his absence and results of RST will be binding
on supplier. In case the selected transformer fails in any of the tests, complete lot of
transformers will be rejected.
32.0 Inspection & Testing of Transformer Oil:
The tenderer shall make arrangements for testing of transformer oil to be used in
the transformers and testing will be done in presence of purchaser's
representative.
To ascertain the quality of transformer oil, original manufacturer's test report
should be furnished to EE (Testing) at the time of factory inspection for
acceptance of the lot.
33.0 Quality Assurance
33.1 The bidder shall invariably furnish following information along with the offer
failing to which the offer will be rejected.

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 28

33.2 Certificates of following materials.

i. Copper conductor
ii. Transformer oil
iii. Core
iv. Insulating paper.
v. Porcelain Bushings
vi Steel Plate used for Tank
33.3 Names of the supplier for the raw material, list of standard accordingly to which the
raw materials are tested, list of test normally carried out on raw materials in
presence of bidder‘s representatives, copies of type test certificates to be furnished.
33.4 Information and copies of test certificate as in (33.3) above respect of bought out
accessories including terminal connectors.
33.5 List of manufacturing facilities available, in this list the bidder shall specifically
mention whether lapping machine, vacuum drying plant, air conditioned dust free
room with positive air pressure for provision of insulation and winding etc are
available with him.
33.6 Level of automation achieved and list of areas where manual processing still exists.
33.7 List of areas in manufacturing process where stage inspection are normally carried
out for quality control and details of such tests and inspections.
33.8 Special features provided in the equipments to make it maintenance free
33.9 List of testing equipment available with the bidder for final testing of transformers
and test plant limitation, if any, vis-à-vis the type, special acceptance and routine
tests specified in the relevant standards and the present specification. These
limitations shall be very clearly brought out in Schedule – D i.e. schedule of
deviations from specified test requirements.
33.10 The successful bidder shall submit the Routine Test Certificate along with
documentary
evidence having paid for the excise duty for the following raw materials viz Oil,
Copper for conductors, insulating materials, Core materials, Bushing at the time of
routine Testing of the fully assembled transformer.

34.0 Qualifying Requirement: As per Tender

35.0 Final Inspection

10 % of the transformers offered will be tested for all tests without opening the
transformer. Heat Run Test will have to be carried out on the transformer having
maximum no load and full load losses taken together. Chief Engineer (MM Cell )
will depute his representatives from testing and inspection wing at the time of final
inspection.
35.1 Leakage test on sample transformer shall be carried out during final inspection as per
relevant IS.

36.0 Performance Guarantee:

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 29

All transformers supplied against this specification shall be guaranteed for a period
of 66 months from the date of receipt at the consignee‘s Stores Center or 60 months
from the date of commissioning, whichever is earlier. However, any engineering
error, omission, wrong provisions, etc. which do not have any effect on the time
period, shall be attended to as and when observed/ pointed out without any price
implication.
37.0 COST DATA SHEET:-
The bidders shall submit the cost data sheets indicating the break up prices and
quantity of each raw material and components along with the unit rates required for
manufacture the offered transformers along with the offer. The cost data sheet
format is enclosed herewith.. If the rates quoted are not justified with the cost data
sheets, the offer shall not be considered for evaluation and placement of the order.
The cost data sheets shall be scrutinized by MM Cell section.
FORMAT FOR COST DATA
ITEM ------ KVA , ------- KV DISTRIBUTION TRANSFORMER
UNIT
Sr.
PARTICULARS UNIT RATES QTY AMT (Rs.)
No.
Rs.
1 CORE (M4 or better ) KG
ALUMINIUM/COPPER WITH
2 KG
DPC FOR HV WINDING
ALUMINIUM/COPPER WITH
3
DPC FOR LV WINDING
3 INSULATION PAPER Meter
4 OIL LTRS
5 TANK NO
6 CHANNELS KG
7 INSULATORS/BUSHINGS KG
LUMP
8. OTHERS
SUM
TOTAL
WASTAGE @ %

38.0 Schedules
38.1 The bidder shall fill in the following schedules which form part of the tender
specification and offer. If the schedules are not submitted duly filled in with the
offer, the offer shall be rejected.

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 30

Schedule `A' -Guaranteed Technical Particulars

Schedule `B' -Schedule of Tenderer's Experience.
38.2 The discrepancies between the specification and the catalogs, Literatures and
indicative drawings which are subject to change, submitted as part of the offer, shall
not be considered and representation in this regard will not be entertained.
38.3 The Bidder shall submit the list of orders for similar type of equipments, executed
of under execution during the last three years, with full details in the schedule of
Tenderer's experience (Schedule `B') to enable the purchaser to evaluate the tender.

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 31

Schedule `A'
GUARANTEED TECHNICAL PARTICULARS
As indicated in E-Tendering GTP Parameter

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 32

SCHEDULE – ‗B‘

SCHEDULE OF TENDERER'S EXPERIENCE

Tenderer shall furnish here a list of similar orders executed/under execution by him to
whom a reference may be made by Purchaser in case he considers such a reference
necessary.
--------------------------------------------------------------------------------------------------------------
Sr. Name of client Value Period of supply Name & Address to
No. & Description. Of Order & commissioning whom reference may
(along with cap. be made.
of T/F)
--------------------------------------------------------------------------------------------------------------
1 2 3 4 5
--------------------------------------------------------------------------------------------------------------

NAME OF FIRM _________________________________

NAME & SIGNATURE OF TENDERER_______________

DESIGNATION____________________________________

DATE____________________________________________

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 33

Annexure I
Air Pressure Test
Name of Supplier:
Order No.:
Capacity & Voltage Ratio of Distribution Transformer : ______ kVA, ____/0.433 kV
Vector Group Dyn11
Sr. No. of equipment Tested:
Date of Testing:
Reference Standard
All the opening of the transformer tank were closed with suitable gasket, bushing,
valves and plugs. The compressor pipe connected at oil filling hole on conservator and a
pressure guage was fitted at air vent plug. The parallel string were places around the tank,
the distance between string and tank as shown in following diagram were recorded before
applying the pressure and after releasing pressure.

Tank Thickness: Side _ mm. Top & Bottom mm

2
Test Pressure : ______ kg/cm applied for 30 Minutes.
Test Point Distance before Test Distance after release Deflection
of Pressure in mm
In mm In mm
A
B
C
D

Permanent Deflection : ________ mm

Permissible Limit of Permanent Deflection as per Specification : _____ mm

Test witnessed by Tested by

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 34

Annexure II
Unbalance Current Test
Name of Supplier:
Order No.:
Capacity & Voltage Ratio of Distribution Transformer : ______ kVA, ____/0.433 kV
Vector Group Dyn11
Sr. No. of equipment Tested:
Date of Testing:
Reference Standard
Transformer Secondary terminals 2U, 2V & 2W are shorted. The shorted 2U, 2V &
2W is connected to 2N through Ammeter. The primary terminals 1U, 1V & 1W are
connected to supply. The rated current _____ A is fed to primary and unbalance current is
noted on Ammeter.

Unbalance Current Measured in Ammeter : ______ A

Rated current in Secondary Side : ____________ A
Permissible limits as per specification : 2% of the Rated current in Secondary Side
% of Unbalance current with reference to Rated current in Secondary Side

Unbalance Current x 100

=
Rated current in Secondary Side
=

Test witnessed by Tested by

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 35

Annexure III
Temperature Rise Test
Name of Supplier:
Order No.:
Capacity & Voltage Ratio of Distribution Transformer : ______ kVA, ____/0.433 kV
Vector Group Dyn11
Sr. No. of equipment Tested:
Date of Testing:
Reference Standard
H. V. Winding L. V. Winding
Rated Line Current in Amp

Guaranteed No Load Losses ________ watt

Load Losses ________ watt
Total Losses ________ watt

P. T. Ratio : _______/____ =
C. T. Ratio : _______/_____ =
Wattmeter Constant =
Total Multiplying Factor (MF) =
Ambient Temp.
Rise in Top Oil Temp. °C

Multiplying Factor (MF)

Line Current in Amps
Line Voltage in Volts

W1+W2+W3 watt
Top Oil Temp. °C
Average °C

Total Watt
W1 watts

W2 watts

W3 watts
TIME

T1 °C

T2 °C

T3 °C

Reduced to Rated Current ________ amps

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 36

Calculation of Temperature Rise in Winding

LV Winding : Since the resistance of LV winding is less than 0.005 ohm, Temperature Rise
in LV Winding is taken as temperature rise of oil as per clause no. 4.3 of IS:2026 (Part
II)/1977
Temperature Rise in LV Winding = __________ °C
HV Winding Resistance across 1U1V at _______°C = _______ ohm
Measurement of Hot Resistance of HV Winding after Shut Down.

Time Resistance

Hot winding Resistance at Ambient Temperature ___ °C (from graph) = _

Ohm
Temperature Rise in H. V. Winding is
Hot Resistance x(235+Cold Ambient Temperature)
= - (235+Hot Ambient Temperature
Cold Resistance
=
=
Results :
1) Temperature Rise in Oil = _________ °C
2) Temperature Rise in LV Winding = _________ °C
3) Temperature Rise in HV Winding = _________ °C
4) Oil leakage test:
The oil leakage test shall be conducted on one unit selected from the offered lot of
each rating. Transformer complete in all respects shall be subjected to the
pressure of 0.4 kg/cm2 and maintained for 8 hours . No leakage should occur.

Test witnessed by Tested by

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 37

SCHEDULE - A
GURANTEED TECHNICAL PARTICULARS
Sr. Remark
GTP Parameters
No.
1 Name of Manufacturer T
2 Reference Standards T
3 Rating of Transformer in KVA N
4 Primary voltage in kV N
5 Secondary voltage in Kv N
6 Transformer shall be Oil Natural Air Natural (ONAN) type Yes/No B
7 Transformer shall be suitable for Outdoor/ Indoor application. (Yes/No) B
8 Transformer shall be Oil Natural cooled type (yes/No) B
9 Highest System Voltage in Kv N
10 Frequency in HZ. N
11 Transformer shall be suitable for solid neutral earthing (Yes/No) B
12 Service condition shall be applicable as per Technical specification clause no. 3 B
13 Transformer Colour as per IS:5 (Shade no. 108) T
14 Type of connection for H.V. Winding (Delta) (Yes/No). B
15 Type of connection for L.V. Winding (Star) (Yes/No) B
16 Vector Group Dyn-11 (Yes/No) B
17 Name Plate details are as per the requirement specified in tender (Yes/No) B
18 Thickness of Name plate (in SWG) N
19 Maximum temperature rise of Windings over an Ambient temp. of 50°C in °C in N
20 Maximum temperature rise of oil over an Ambient temp. of 50°C in °C in N
21 Approximate overall length of the Transformer in mm N
22 Approximate overall breadth of the Transformer in mm N
23 Approximate overall height of the Transformer in mm N
24 Approximate length of the Transformer tank in mm N
25 Approximate breadth of the Transformer tank in mm N
26 Approximate height of the Transformer tank in mm N
27 Thickness of the side of transformer tank plates in mm N
28 Thickness of the bottom of transformer tank plates in mm N
29 Thickness of the top of transformer tank plates in mm N
30 Size of reinforced welded angle to the Transformer Tank in mm. T
31 Degree of slope to the top plate of Transformer T
32 Shape of transformer Tank T
33 Type of Tank (Corrugated/ Conventional) T
34 In case of corrugated tank, thickness of corrugated sheet (in mm) T
35 Size of Transformer Base Channel in mm. T
36 Size (diameter & width) and No. of Rollers provided to the Transformer T
37 Conservator tank to the transformer with oil level indicator (showing three levels) and drain B

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 38

plug is provided ( Yes/ No)

38 Dimensions of conservator Tank (LxD) in mm T
39 Drain Valve size provided to the transformer tank ( Yes/No) B
40 Size of Oil filling hole with cap in mm. (on conservator) is provided. B
41 Size of Drain valve in mm. is provided. T
42 Size of filter valve in mm. is provided. T
43 No. & Size in mm of Lifting lugs provided to transformer T
44 No. & Size in mm of pulling lugs provided to transformer T
45 No. & Size in mm of transformer top cover lifting lugs provided to transformer T
46 No. of Earthing terminals with suitable size in (SWG) T
47 Thermometer pocket is provided (Yes/No) B
48 Quantity of Silica-Gel filled in breather ( in gm) & make of breather T
49 Explosion vent with diaphragm. (Yes/No) B
50 No of radiators both on HV & LV side provided and location with arrangement & size. T
51 Thickness of the radiator of transformer in mm. N
52 No of radiator fins. N
53 (A) Radiating surface of radiators in Sq. Mtrs. N
54 (B) Radiating surface of Tank only in Sq. Mtrs. N
55 Total radiating surface of transformer tank in Sq. mtrs. N
Off Load Tap changer on higher voltage winding for variation of H.V voltage within range
56 T
of (+) 5% to (-) 15% insteps of 2.5 % provided (Yes/No)
57 Weight of Core in kgs N
58 Weight of copper (Winding) in Kgs. N
59 Weight of Transformer Tank with fittings in Kgs. N
60 Weight of Oil in kgs N
61 Volume of Oil in Ltrs N
62 Total weight of Transformer in Kgs N
63 Rating of Lightening Arrestors and Make thereof (kV, kA) T
64 Reference Standard of Lightening Arrestors. T
65 Min. External Clearances of HV Bushing terminals between Ph to Ph (in mm ) N
66 Min. External Clearances of HV Bushing terminals between Ph to E (in mm) N
67 Min. External Clearances of LV Bushing terminals between Ph to Ph (in mm) N
68 Min. External Clearances of LV Bushing terminals between Ph to E (in mm) N
The temperature shall in no case reach a value that will damage the core itself , other parts
69 B
or adjacent materials (Yes/No)
70 Type of Core (stacked/ wound) T
71 Core material used & its grade T
72 Thickness of core lamination in mm T
73 No of steps used in CRGO Core N
74 Diameter of the core (in mm) T
75 Effective Core Area ( Sq. cm) T

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 39

76 Flux density at normal voltage and frequency in Tesla N

77 Material of H.V. Winding T
78 Material of L.V. Winding T
79 Size/diameter of conductor used for HV winding in mm T
80 Total cross section area of HV Winding in sq mm. N
81 Size of strip used for LV winding conductor in mm T
82 Total cross section of Copper used in LV Winding in sq. mm N
83 No. of conductors in parallel of LV winding T
84 Current density of HV winding , in Amps/sq. mm. T
85 Current density of LV winding, in Amps / sq.mm. T
86 No of HV winding Turns T
87 No of LV winding Turns N
88 No of H.V. coils /phase N
89 No. of L.V. coils/phase T
90 Resistance of HV winding at 20 º C in Ohm/phase N
91 Resistance of LV winding at 20 º C in Ohm/phase N
92 % impedance value at 75º C N
93 Name of manufacturer of oil T
94 Grade of Oil T
95 A. Minimum volume of oil in liters as per clause No. 9 of tech. specification T
96 B. Quantity of total oil absorption (in Ltrs) in first filling T
97 Total oil Volume including Total Oil absorption in liters i.e. (A+B) N
98 Breakdown value of oil at the time of first filling (KV/mm) considering 2.5 mm gap T
Total volume of conservator shall be such as to content 10% of total quantity of oil
99 B
(Yes/No)
100 Max. core (No load) losses at rated voltage and frequency in Watts T
101 Max. Total losses (No load loss + Load Loss) at 50 % loading in Watts at 75ºC T
102 Max. Total losses (No load loss + Load Loss) at 100 % loading in Watts at 75ºC N
Magnetizing current (No load) in Amps & its % of full load current & rated voltage referred
103 T
to LV side
Magnetizing current (No load) in amps & its % of full load current at maximum voltage
104 T
(112.5% of rated voltage ) referred to LV side
105 Clearance between Core & L.V. in mm N
106 Clearances between L.V. & H.V. in mm N
107 Clearances between winding to body of tank in mm N
108 Clearance between HV phase to phase in mm N
109 Clearances between end insulation to Earth in mm N
110 Insulation materials provided for core T
111 Insulation materials provided for H.V. Conductor T
112 Insulation materials provided for L.V. Conductor T
113 Thickness of locking spacers between HV coils in mm T
114 Inter layer insulation provided in H.V winding to design for Top & bottom layer T

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 40

115 Inter layer insulation provided in L.V winding to design for Top & bottom layer T

116 Inter layer insulation provided in between all layer in H.V winding T
117 Inter layer insulation provided in between all layer in L.V winding T
118 Details of end insulation (thickness in mm) N
119 Whether wedges are Provided at 50% turns of the Coil (Yes/ No) B
120 Thickness of insulating paper N
121 Regulation at 0.8 P.F. lag ( in %) N
122 Regulation at 0.8 P.F. leading ( in %) N
123 Regulation at unity P.F.. (in %) N
124 Reference standard of Bushing T
125 Material of HV and L.V Bushings T
126 Makes of HV and L.V Bushings T
127 Rating of HV Bushing ( in KV,A) T
128 Rating of LV Bushing (in KV,A) T
129 Minimum Creepage Distance of HV Bushings in mm (min 25mm/kV) N
130 Minimum Creepage Distance of LV Bushings in mm (min 25mm/kV) N
131 Power frequency withstand voltage dry & wet in kV(rms) for HV Bushings N
132 Dry lighting impulse withstand voltage test in kV (Peak) stating the waveform adopted T
133 for HV Bushing. T
134 Separate source power frequency withstand test for HV for 1minute in kV(min) T
135 Separate source power frequency withstand test for LV for 1minute in kV(min) T
136 Induced over voltage withstand test for 1 min. specify voltage frequency, time for test. T
137 Impulse test value (in kVp) . T
4P 3-G air filled cable box shall be suitable to 3.5 core PVC aluminum cable with copper
138 flats filled on L.T. studs to connect XLPE cable shall be provided on L.V. side (Yes/No) & T
size of cable in sq.mm (shall be mentioned)
139 Efficiency at 75 º C at unity P.F. at 125 % Load N
140 Efficiency at 75 º C at unity P.F at 100 % Load N
141 Efficiency at 75 º C at unity P.F. at 75 % Load N
142 Efficiency at 75 º C at unity P.F. at 50 % Load N
143 Efficiency at 75 º C at 0.8 P.F. lag at 125 % Load N
144 Efficiency at 75 º C at 0.8 P.F. lag at 100 % Load N
145 Efficiency at 75 º C at 0.8 P.F. lag at 75 % Load N
146 Efficiency at 75 º C at 0.8 P.F. lag at 50 % Load N
147 Efficiency at 75 º C at 0.8 P.F. lag at 25 % Load N
148 Efficiency at 75 º C at 0.8 P.F. leading at 125 % Load N
149 Efficiency at 75 º C at 0.8 P.F. leading at 100 % Load N
150 Efficiency at 75 º C at 0.8 P.F. leading at 75 % Load N
151 Efficiency at 75 º C at 0.8 P.F. leading at 50 % Load N
152 Efficiency at 75 º C at 0.8 P.F. leading at 25 % Load N

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 41

153 The test certificates of copper conductors, core , insulating paper, porcelain Bushings, steel B
plate used for enclosure of the offered transformer are enclosed with the offer(Yes/No)
All type test report carried out on transformer at NABL laboratory shall be submitted along
154 with the offer as per cl. XXII (c) of Section (I) i.e. Instructions to tenderers. (Yes/No). Firm B
may attach online.
Unbalance current test, Air pressure test and temperature rise test shall be conducted as per
155 B
format enclosed with the technical specification along with the offer (Yes/ No)
All drawings shall be furnished for each offered item separately along with this offer (Yes/
156 B
No)
157 Oil absorption calculation sheet shall be furnished for each offered item separately along B
with this offer (Yes/ No)
158 Heat dissipation calculation shall be furnished for each offered item separately along with B
this offer (Yes/ No)
Calculation sheet submitted for Flux density calculations (stating HV & LV turns) for each
159 B
offered item separately along with the offer (Yes/No)
Calculation sheet for 112% of rated V/f ratio (Over fluxing) calculation sheet shall be
160 B
furnished for each item separately along with this offer (Yes/No)

161 Required documents, plant and machinery, testing equipment , list of order executed/under B
execution shall be furnished for each offered item separately along with this offer (Yes/ No)
162 The information required under Quality Assurance shall be submitted with the offer in B
physical format & soft copy(Yes/ No)
163 The cost data in the prescribed format shall be submitted with offer in physical format & B
soft copy (Yes/ No)
164 The performance Guarantee of the transformers in years NUMERIC N

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 42

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 43

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 44

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 45

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 46

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 47

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 48

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 49

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 50

Technical Specification No. CE/MMC/MSC-II/3Phase/DT/T/2017/03,Date: 12.05.2017. Page 51

25-200-Kva pdf01 06 2017
No ratings yet
25-200-Kva pdf01 06 2017
49 pages
Earthing System Installation Guide
No ratings yet
Earthing System Installation Guide
5 pages
Transformer & Cable Specs
No ratings yet
Transformer & Cable Specs
297 pages
S&C Power Fuses
0% (1)
S&C Power Fuses
28 pages
Method of Statement For Earthing Mesh. (N-IMS-NTT-P-ME-32-21)
100% (1)
Method of Statement For Earthing Mesh. (N-IMS-NTT-P-ME-32-21)
6 pages
Meralco Service Application Guide
No ratings yet
Meralco Service Application Guide
32 pages
Substation Earthing System
No ratings yet
Substation Earthing System
11 pages
Typical Data Sheet Neutral Earthing Resistor
No ratings yet
Typical Data Sheet Neutral Earthing Resistor
2 pages
Medium Voltage Cable
No ratings yet
Medium Voltage Cable
5 pages
Table 310.15 (B)
No ratings yet
Table 310.15 (B)
1 page
V16 - Malvar - Bulihan.r1
No ratings yet
V16 - Malvar - Bulihan.r1
14 pages
Load Schedule
No ratings yet
Load Schedule
5 pages
Technical Specification For Earth Wire
100% (1)
Technical Specification For Earth Wire
2 pages
EEMAC Codes & Standards
0% (1)
EEMAC Codes & Standards
2 pages
4 Porcelain Insulators
No ratings yet
4 Porcelain Insulators
17 pages
Eep-Internal Arc Testing of MV Switchgear IEC 62271200 Part One
No ratings yet
Eep-Internal Arc Testing of MV Switchgear IEC 62271200 Part One
2 pages
Technical Information To Install and Establish Earthing System Connected To Existing Grid Refer To Itb Drawing No
0% (1)
Technical Information To Install and Establish Earthing System Connected To Existing Grid Refer To Itb Drawing No
2 pages
S TR PTR - 00
No ratings yet
S TR PTR - 00
48 pages
EDC-DTS-MV011 - Pole Mounted Load Break Switches and Sectionalizers
100% (1)
EDC-DTS-MV011 - Pole Mounted Load Break Switches and Sectionalizers
37 pages
Xcel Energy Standard For Installation and Use
No ratings yet
Xcel Energy Standard For Installation and Use
180 pages
IEEE STD 824-2004 (Revision of IEEE STD 824-1994)
No ratings yet
IEEE STD 824-2004 (Revision of IEEE STD 824-1994)
63 pages
Derating Factors: Table 10
No ratings yet
Derating Factors: Table 10
1 page
4.3.7.1 - DWG TR Cab 01 00 02-A
No ratings yet
4.3.7.1 - DWG TR Cab 01 00 02-A
1 page
Current Distribution of Single Core Cable On Metal Tray
No ratings yet
Current Distribution of Single Core Cable On Metal Tray
7 pages
LUCY Package Substation Brochure
0% (1)
LUCY Package Substation Brochure
6 pages
Datasheet Cable
No ratings yet
Datasheet Cable
2 pages
Elect 01 Method Statement For Testing of MV Cables Rev 2.0
No ratings yet
Elect 01 Method Statement For Testing of MV Cables Rev 2.0
7 pages
PEXLIM P-Y - Section of Surge Arrester Buyers Guide - Edition 11 2014-05 - English - 1HSM 9543 12-00en
100% (1)
PEXLIM P-Y - Section of Surge Arrester Buyers Guide - Edition 11 2014-05 - English - 1HSM 9543 12-00en
8 pages
Schedule of Charges and Procedure PDF
No ratings yet
Schedule of Charges and Procedure PDF
58 pages
25-0409 Steel Asia Project - Supply of MDP
No ratings yet
25-0409 Steel Asia Project - Supply of MDP
4 pages
CEA Safety Regulations 2010 PDF
No ratings yet
CEA Safety Regulations 2010 PDF
87 pages
Electrical Construction
No ratings yet
Electrical Construction
33 pages
111 - 2. 2025 MVA 13233 KV Power TF
No ratings yet
111 - 2. 2025 MVA 13233 KV Power TF
32 pages
Catalogo TKG Cable
No ratings yet
Catalogo TKG Cable
8 pages
GIS Termination
No ratings yet
GIS Termination
6 pages
Is 398 (Part Iii) 1976
No ratings yet
Is 398 (Part Iii) 1976
17 pages
Wire and Cable Installation
100% (1)
Wire and Cable Installation
9 pages
2011 NEC Code 314.28
No ratings yet
2011 NEC Code 314.28
2 pages
Page 6
No ratings yet
Page 6
2 pages
METHOD STATEMENT - Trunking
100% (1)
METHOD STATEMENT - Trunking
1 page
M S Distribution Board
No ratings yet
M S Distribution Board
7 pages
FS 4011 Electrical, Instrumetation and Communication Cables
No ratings yet
FS 4011 Electrical, Instrumetation and Communication Cables
16 pages
Masterpact NW12H2 Circuit Breaker Specs
No ratings yet
Masterpact NW12H2 Circuit Breaker Specs
3 pages
Low Voltage Cables & Wires Guide
No ratings yet
Low Voltage Cables & Wires Guide
13 pages
132kV Cable Specs Rev.2 1600Sq - MM Altay-IA17 UGC
No ratings yet
132kV Cable Specs Rev.2 1600Sq - MM Altay-IA17 UGC
46 pages
Engineering Bulletintable of Contentspdf
No ratings yet
Engineering Bulletintable of Contentspdf
2 pages
Disconnecting Switch 1 General
No ratings yet
Disconnecting Switch 1 General
6 pages
PEC 2009 Tables
100% (3)
PEC 2009 Tables
21 pages
PEL Presentation English
No ratings yet
PEL Presentation English
29 pages
LAD-05 Determination of LESCO For Investment Plan 2023-24 To 2027-28 26-04-2023 2325-31
No ratings yet
LAD-05 Determination of LESCO For Investment Plan 2023-24 To 2027-28 26-04-2023 2325-31
47 pages
Technical Specification of 315-2500 KVA Distribution Transformer
83% (6)
Technical Specification of 315-2500 KVA Distribution Transformer
51 pages
5kva 20 Kva Dist - Transformer Spec Uploaded Website 2711
No ratings yet
5kva 20 Kva Dist - Transformer Spec Uploaded Website 2711
40 pages
10kva 25 Kva Dist - Transformer Spec Revision Dtd. 20.04.2018
No ratings yet
10kva 25 Kva Dist - Transformer Spec Revision Dtd. 20.04.2018
45 pages
Transformer Specs for Engineers
No ratings yet
Transformer Specs for Engineers
68 pages
315KVA ID 11 22 KV T HTM1 04 0819
No ratings yet
315KVA ID 11 22 KV T HTM1 04 0819
64 pages
TechnicalSpecSingle Phase 25 KVA 11 22 KV DT 05062017
No ratings yet
TechnicalSpecSingle Phase 25 KVA 11 22 KV DT 05062017
40 pages
8 16 kVA 25kVA11 KV
No ratings yet
8 16 kVA 25kVA11 KV
66 pages
34 TRF 20-11-2019
No ratings yet
34 TRF 20-11-2019
54 pages
63-100 Kva Tf-Rural-907
No ratings yet
63-100 Kva Tf-Rural-907
91 pages
Specs 5mva-10mva Msedcl
No ratings yet
Specs 5mva-10mva Msedcl
22 pages
JB Gupta Remaining Pages 425 To 440
No ratings yet
JB Gupta Remaining Pages 425 To 440
16 pages
UPPCL UPRVUNL JE Electrical Trani Solve Paper
No ratings yet
UPPCL UPRVUNL JE Electrical Trani Solve Paper
876 pages
Command Window
No ratings yet
Command Window
1 page
MOP Annual Report Eng 2023-24
No ratings yet
MOP Annual Report Eng 2023-24
207 pages
Analyzing Chemical Degradation of Power Transformers Using Smart Intelligence System
No ratings yet
Analyzing Chemical Degradation of Power Transformers Using Smart Intelligence System
5 pages
CamScanner Document
No ratings yet
CamScanner Document
131 pages
Hw-b750d Xu Wug 00 Eng 240202.0 Samsung Soundbar HW b750d
No ratings yet
Hw-b750d Xu Wug 00 Eng 240202.0 Samsung Soundbar HW b750d
42 pages
Solar-Powered Battery Charger PDF
No ratings yet
Solar-Powered Battery Charger PDF
3 pages
High Voltage Transformer Testing
No ratings yet
High Voltage Transformer Testing
7 pages
Companion 3 Series Ii SM - R05
100% (1)
Companion 3 Series Ii SM - R05
30 pages
Trinitron Kv27s22
No ratings yet
Trinitron Kv27s22
51 pages
Lab Report Three
No ratings yet
Lab Report Three
4 pages
Introductory Handbook On Microprocessor Controlled Electric Locomotives PDF
100% (1)
Introductory Handbook On Microprocessor Controlled Electric Locomotives PDF
35 pages
Modbus Registers Map-Conext CL 60E & CL 60A
No ratings yet
Modbus Registers Map-Conext CL 60E & CL 60A
14 pages
STM 4532
No ratings yet
STM 4532
11 pages
SPC3U02 Universal Control Unit Datasheet Iss 1 April 2023
No ratings yet
SPC3U02 Universal Control Unit Datasheet Iss 1 April 2023
2 pages
Photo Tube
No ratings yet
Photo Tube
2 pages
Solar Module Installation Guide
No ratings yet
Solar Module Installation Guide
45 pages
Asymmetrical Full-Bridge Converter
No ratings yet
Asymmetrical Full-Bridge Converter
9 pages
Connector For FLEXWELL® Elliptical Waveguide E100, PBR100 Flange
No ratings yet
Connector For FLEXWELL® Elliptical Waveguide E100, PBR100 Flange
1 page
Utility Bill
No ratings yet
Utility Bill
1 page
2.4 Band Theory of Solids
No ratings yet
2.4 Band Theory of Solids
5 pages
User Manual Samsung 8K BN68-13708A-01 - UM - QN700B-QN900B - LATIN - L02 - 220527.0
No ratings yet
User Manual Samsung 8K BN68-13708A-01 - UM - QN700B-QN900B - LATIN - L02 - 220527.0
2 pages
PowerElectronics Grid-Forming Case Studies 15.20
No ratings yet
PowerElectronics Grid-Forming Case Studies 15.20
17 pages
Micro IDSD BL Manual
No ratings yet
Micro IDSD BL Manual
1 page
A 10-mW Two-Channel Fully Integrated System-on-Chip For Eddy-Current Position Sensing
No ratings yet
A 10-mW Two-Channel Fully Integrated System-on-Chip For Eddy-Current Position Sensing
10 pages
Ravi Sir Name Plate
No ratings yet
Ravi Sir Name Plate
5 pages
E11F01P19 Product Specifications Dip 18-26
No ratings yet
E11F01P19 Product Specifications Dip 18-26
4 pages
Chapter 7 Electronic Analysis of CMOS Logic Gates
No ratings yet
Chapter 7 Electronic Analysis of CMOS Logic Gates
42 pages
KLS Martin MarLED E3 Operating Light - Service Manual
No ratings yet
KLS Martin MarLED E3 Operating Light - Service Manual
192 pages
HendrixACS - 2. Application & Design PDF
No ratings yet
HendrixACS - 2. Application & Design PDF
40 pages
NGR Technical Information
100% (1)
NGR Technical Information
6 pages
Bettis 2000 Series E796 M2CP: Installation and Maintenance Manual
No ratings yet
Bettis 2000 Series E796 M2CP: Installation and Maintenance Manual
27 pages
Ifc 100 - V03
No ratings yet
Ifc 100 - V03
8 pages
Solar Ai Fishing Boat
No ratings yet
Solar Ai Fishing Boat
3 pages
Technical Seminar
No ratings yet
Technical Seminar
15 pages