GRAPHIC SCALE IN METERS LEVEL INDICATION:

0 0.5 1 2 SECTION PLAN

1:25

TYPE 1 EMBEDDING OF DRAIN STATION

IN STANDARD TRENCH MODE

B NOTES:
3200
B 1. PIPE PRESSURE RATING ACCORDING TO WALL THICKNESS DETERMINATION REPORT.
2. ALL STATIONS WILL BE PROPERLY MARKED WITH PERMANENT IDENTIFICATION MARKS &SEQUENTIAL NUMBERS.
175 1245 360 1245 175
3. BEFORE PLACING OF THE LEAN CONCRETE UNDER THE FOUNDATIONS, THE CONTRACTOR WILL ENSURE THAT THE
3300
UNDERLYING SOIL HAS BEEN COMPACTED TO MEET THE REQUIREMENTS OF PROJECT SPECIFICATIONS.

100
475 800 1925
3100 4. SHAFT BEDDED ON WELL COMPACTED GRAVEL FILL TO PREVENT ANY LOAD BEING TRANSFERRED TO THE PIPELINE.

50
5. FOR THE LOCATION OF STATIONS REFER TO THE PIPELINE ALIGNMENT SHEETS.

175
6. ALL EMBEDDED STEEL ITEMS ARE HOT DIP GALVANIZED.

250

250
7. ALL CORNERS ARE TO BE CHAMFERED TO 20mm.
01 01
8. BACKFILLING SHALL BE DONE IN UNIFORM LAYERS OF 0.25m THICKNESS. BACKFILL SHALL BE COMPACTED TO AT

1125
03

515

515
LEAST 95% PROCTOR DENSITY.

590
WALL PROTECTION PLATE

110
60

60
AERATION PIPE CT 09 1000x1000 mm THICKNESS 6 mm
554 450 9. THIS DRAWING IS FOR GENERAL ARRANGEMENT ONLY.

875
260
SLAB TYPE 1 SLAB TYPE 2
< SLOPE MIN. 1% < SLOPE MIN. 1% 10. ALL DIMENSIONS ARE IN MILLIMETERS, ELEVATIONS ARE IN METERS.
BLIND FLANGE04 11. PIPES, FITTINGS, FLANGES, BOLTINGS AND GASKETS INSIDE STATION SHALL FULFILL REQUIREMENTS OF DOC. No.
875 720
A 1605
A A 2" #300
A

150
BALL VALVE QC10-H-048 SPECIFICATION M08: PIPING MATERIALS FOR STATIONS.
2400

2050

2500

2300
VARIABLE 2" #300 120 VARIABLE 12. THE INTERNAL LINING OF PIPES, FITTINGS, AND OTHER PIPING COMPONENTS INSIDE DRAIN STATION SHALL BE

50
BALL VALVE
MAIN PIPE 12''
2" #300 02 DONE WITH FUSION BONDED EPOXY ACC. TO DOC. No. QC10-H-060 SPECIFICATION M20: FUSION-BONDED EPOXY

1210
WALL DUCT WATERTIGHT
PUMP SUMP MAIN PIPE 12''
800

TYPICAL MANHOLE COVER 800 x 800 LAID IN FORM WORK CT 10

800
LINING.
WATERTIGHT AND DUST PROOF
℄ GALVANIZED
STEEL LADDER
℄ 13. THE EXTERNAL COATING OF PIPES, FITTINGS AND OTHER PIPING COMPONENTS INSIDE DRAIN STATION SHALL BE

125
DONE ACC. TO DOC. No. QC10-H-061 SPECIFICATION M21: PAINTING OF PIPING, EQUIPMENT AND STRUCTURAL
STEELWORK.
14. THE COATING OF BURIED JOINTS, FITTINGS AND OTHER PIPING COMPONENTS INSIDE DRAIN STATION SHALL BE
475

250
LIFTING DEVICE CT 07
DONE WITH HEAT SHRINKABLE SLEEVES ACC. TO DOC. No. QC10-H-062 SPECIFICATION M22: LIQUID-EPOXY COATING.
175

15. FENCING TO BE PROVIDED FOR DRAIN STATION EXCEPT WITHIN MOT-ROW.

1595 1595 MINIMUM DISTANCE BETWEEN SHAFT AND FENCE SHALL BE 1,0m DEPENDING ON LOCAL SITE CONDITIONS.
250 250

100
FENCING CONSISTS OF 3,0m HIGH WIRE MESH FENCE.
10 100 175 800 1625 100
16. THE AERATION PIPES TO BE ROUTED UNDERGROUND TO EDGE OF ROW IF ARRANGED WITHIN MOT-ROW

B B

LEGEND:
PLAN 1-1 PLAN 2-2 STRUCTURE:

SCALE 1:20 SCALE 1:20 PRECAST CONCRETE FOR WALLS & SLABS CEMENT SCREED

PREFABRICATED COVER SAND GRAVEL MATERIAL

GRATING EARTH

LEAN CONCRETE FENCE

IN SITU REINFORCED CONCRETE SAND / GRAVEL

SELECTED BEDDING MATERIAL

ALL CONCRETE STRUCTURES WITH A FLOOR LEVEL BELOW PERMANENT

TANKING: GRADE SHALL HAVE THE UNDERGROUND PART COMPLETELY ENCASED
IN A TANKING MADE FROM PREFABRICATED HEAVY DUTY WATER PROOFING
MEMBRANE OF MODIFIED BITUMEN, MINIMUM 4 MM THICK AND WITH A POLYESTER
NON-WOVEN FABRIC BASE. THE TANKING ON THE SIDES AND THE
TOPS OF THE STRUCTURES SHALL BE FULLY TORCH-APPLIED ON A
4400 5200 BITUMEN-PRIMED SURFACE. THE PROTECTION MATERIAL SHALL CONTINUE TO A
LEVEL NOT LESS THAN 0.2M ABOVE FINAL GRADE (STATION ELEVATION). THE TANKING
UNDER THE STRUCTURES SHALL BE LAID ON A CONCRETE BLINDING AND PROTECTED
BY A CONCRETE OVERLAY OF MINIMUM 50 MM THICKNESS. ALL OVERLAPS SHALL BE
HCIS CLASS 4 FENCE HCIS CLASS 4 FENCE HCIS CLASS 4 FENCE HCIS CLASS 4 FENCE MINIMUM 100 MM AND FULLY TORCH-WELDED. PROTECTION MEMBRANE FOR
VERTICAL ELEMENTS SHALL BE PROVIDED BY 4MM THICK BITUMAT.

SEE NOTE 15 SEE NOTE 15 SEE NOTE 15 SEE NOTE 15

STEEL FENCE STEEL FENCE STEEL FENCE STEEL FENCE

TYPICAL MANHOLE COVER 800 x 800

WATERTIGHT AND DUST PROOF
2400
3200

250 1800
250 1 250 2600 250
1
TYPICAL MANHOLE COVER 800 x 800
50 WATERTIGHT AND DUST PROOF 50 50 50
250 825 800 425 250 1625 800 425

PREFABRICATED COVER REMOVABLE PREFABRICATED COVER REMOVABLE

AERATION PIPE CT 09
PREFABRICATED COVER SLAB CT 06 SLAB JOINT CT 08 PREFABRICATED COVER SLAB CT 06

1000 1000 AERATION PIPE CT 09

1000 1000
MIN.600 MM

MIN.600 MM
240

240
REFERENCE DRAWING:
20

20
DRAWING No. TITLE
340

340
HIGHEST
825 800 175 BACKFILL LEVEL 1300 325 800 175
1220

1220
10-QP10-P-001 TI-RNGL GENERAL PLOT PLAN
90-ZG21-R-002 TYPICAL DRAIN STATION, STATIC DESIGN CALCULATION
90-ZG21-V-002 TYPICAL DRAIN STATION, FORMWORK DRAWING
CT 11 2 2 90-ZG21-W-002 TYPICAL DRAIN STATION, REINFORCEMENT DRAWING
90-ZG21-L-002 TYPICAL DRAIN STATION, REINFORCEMENT LIST

SAND GRAVEL
MATERIAL
GALVANIZED STEEL LADDER,ACC.TO BS4211 OR
AN EQUIVALENT STANDARD,ENCASED IN CONCRETE
GALVANIZED STEEL LADDER,ACC.TO BS4211 OR
AN EQUIVALENT STANDARD,ENCASED IN CONCRETE
ENGINEER'S STAMP: CONTRACTOR'S STAMP:

RR DOCUMENT COMMENT SHEET

SELECTED BEDDING No. 90-ZG21-S-012 No. WT-SC-D-278
VARIABLE

VARIABLE
MATERIAL MAIN PIPE 12'' Rev. A Date 09/12/2024
STATUS A: Approved for construction (AFC)
℄ ℄

VARIABLE
B: Approved as noted (AAN)
VARIABLE

MAIN PIPE 12'' CT 11

TANKING CT 05
WELDOLET D: For Information only (INF)
MIN.300 MM
300

PRE-FABRICATED WALL PRE-FABRICATED WALL

AND BOTTOM FRAME 325 305 219 156 AND BOTTOM FRAME
CEMENT GROUT
VARIABLE

02 06 03 02
CEMENT GROUT 01

110
60
590 04
TANKING CT 05 SLOPE MIN. 1% > WALL PROTECTION PLATE
1000x1000 mm THICKNESS 6 mm

GALVANIZED GRATING
05 0 ISSUED FOR CONSTRUCTION W.A M.O A.Y 14.12.2024
UPN-100 WITH U-BOLT GALVANIZED GRATING
STEEL SUPPORT VARIABLE A ISSUED FOR APPROVAL W.A M.O A.Y 21.10.2024
608

608
UPN-100 WITH U-BOLT

583
L-PROFILE (BOLTED) L-PROFILE (BOLTED)
STEEL SUPPORT
1340

1340
REV. ISSUED FOR BY CHECKED APPROVED DATE
SLOPE 2% ► WALL DUCT WATERTIGHT SLOPE 2% ►

100
SLOPE SCREED MIN. 25 mm
25

LAID IN FORM WORK CT 10

Project No.
SUMP

SUMP
500

500
WC230098
LEAN CONCRETE LEAN CONCRETE

SLOPE SCREED MIN. 25 mm

400

400
500

500
SAUDI WATER AUTHORITY
100

100
SUMP SUMP

350 979 271 550 350 350 1779 271 550 350
PIPING MATERIAL
400 1800 350 50 400 2600 350 50
ITEM QTY
DESCRIPTION SIZE CLASS FLANGE STD. UNIT
NO SAUDI ARABIAN OIL COMPANY (ARAMCO)
1 PIPE, CS ASTM A53 Gr. B, SCH XS 2" - - * m
LOCATION
BALL VALVE, CS ASTM A2016 Gr. WCB,
2 2" #300 ASME B16.5 2 PC JUBAIL RIYAS NGL WATER TRANSMISSION SYSTEM
FLANGED
SECTION B-B FLANGE WN, CS ASTM A105, RAISED SECTION A-A
3 2" #300 ASME B16.5 1 PC
SCALE 1:20 FACE SCALE 1:20
SAWAED GENERAL CONTRACTING COMPANY
FLANGE BLIND, CS ASTM A105, RAISED
4 2" #300 ASME B16.5 1 PC
FACE RIYAS NGL TIE-IN STATION
ELBOW, LONG RADIUS, CS ASTM A53 TYPICAL DRAIN STATION
5 Gr.B, SCH XS 2" - - 1 PC SCALE
GUIDE DRAWING
WELDOLET, CS ASTM A105, SCH STD x
6 12"x2" - - 1 PC
SCH XS 1:25 DRAWING NO. SHEET REV.

* DEPEND ON SITE CONDITION 9 0 - Z G 2 1 - S - 0 1 2 1/3 0

FINAL
T-B-L Engineering e.U.
ENGINEERING
 GRAPHIC SCALE IN METERS LEVEL INDICATION:

0 0.5 1 SECTION PLAN

1:25

TYPE 2 EMBEDDING OF DRAIN STATION

INSIDE ROW OF MOT

NOTES:

1. PIPE PRESSURE RATING ACCORDING TO WALL THICKNESS DETERMINATION REPORT.

2. ALL STATIONS WILL BE PROPERLY MARKED WITH PERMANENT IDENTIFICATION MARKS &SEQUENTIAL NUMBERS.
3. BEFORE PLACING OF THE LEAN CONCRETE UNDER THE FOUNDATIONS, THE CONTRACTOR WILL ENSURE THAT THE
UNDERLYING SOIL HAS BEEN COMPACTED TO MEET THE REQUIREMENTS OF PROJECT SPECIFICATIONS.
4. SHAFT BEDDED ON WELL COMPACTED GRAVEL FILL TO PREVENT ANY LOAD BEING TRANSFERRED TO THE PIPELINE.
5. FOR THE LOCATION OF STATIONS REFER TO THE PIPELINE ALIGNMENT SHEETS.
6. ALL EMBEDDED STEEL ITEMS ARE HOT DIP GALVANIZED.
B 7. ALL CORNERS ARE TO BE CHAMFERED TO 20mm.
3200 8. BACKFILLING SHALL BE DONE IN UNIFORM LAYERS OF 0.25m THICKNESS. BACKFILL SHALL BE COMPACTED TO AT
MOT ROW

MOT ROW
LEAST 95% PROCTOR DENSITY.
175 175
B 9. THIS DRAWING IS FOR GENERAL ARRANGEMENT ONLY.
1245 360 1245
3300 10. ALL DIMENSIONS ARE IN MILLIMETERS, ELEVATIONS ARE IN METERS.

100
475 800 1925 11. PIPES, FITTINGS, FLANGES, BOLTINGS AND GASKETS INSIDE STATION SHALL FULFILL REQUIREMENTS OF DOC. No.
LIFTING DEVICE CT 07
3100
QC10-H-048 SPECIFICATION M08: PIPING MATERIALS FOR STATIONS.
12. THE INTERNAL LINING OF PIPES, FITTINGS, AND OTHER PIPING COMPONENTS INSIDE DRAIN STATION SHALL BE
175

250
DONE WITH FUSION BONDED EPOXY ACC. TO DOC. No. QC10-H-060 SPECIFICATION M20: FUSION-BONDED EPOXY
01 01 LINING.
13. THE EXTERNAL COATING OF PIPES, FITTINGS AND OTHER PIPING COMPONENTS INSIDE DRAIN STATION SHALL BE
1125

VARIABLE 03 VARIABLE

590
DONE ACC. TO DOC. No. QC10-H-061 SPECIFICATION M21: PAINTING OF PIPING, EQUIPMENT AND STRUCTURAL

875
WALL PROTECTION PLATE
1000x1000 mm THICKNESS 6 mm 554 450 STEELWORK.
< SLOPE MIN. 1% < SLOPE MIN. 1%
VARIABLE 14. THE COATING OF BURIED JOINTS, FITTINGS AND OTHER PIPING COMPONENTS INSIDE DRAIN STATION SHALL BE
SLAB TYPE 3 SLAB TYPE 4 04
VARIABLE DONE WITH HEAT SHRINKABLE SLEEVES ACC. TO DOC. No. QC10-H-062 SPECIFICATION M22: LIQUID-EPOXY COATING.
A A A CT12
A

60
150
60
2400

2050

2500
2300
15. FENCING TO BE PROVIDED FOR DRAIN STATION EXCEPT WITHIN MOT-ROW.
120

60

800
MINIMUM DISTANCE BETWEEN SHAFT AND FENCE SHALL BE 1,0m DEPENDING ON LOCAL SITE CONDITIONS.
02 MAIN PIPE 12''

1210
GALVANIZED FENCING CONSISTS OF 3,0m HIGH WIRE MESH FENCE.
800

MAIN PIPE 12'' STEEL LADDER

WALL DUCT WATERTIGHT 16. THE AERATION PIPES TO BE ROUTED UNDERGROUND TO EDGE OF ROW IF ARRANGED WITHIN MOT-ROW
LOCKABLE MANHOLE COVER, LAID IN FORM WORK CT 10
WATERTIGHT, SUITABLE FOR

125
TRAFFIC LOAD SLW600 (70t)
AERATION PIPE Ø 60
STAINLESS STEEL MESH
℄ AERATION PIPE Ø 60
STAINLESS STEEL MESH
℄
WITH INSECT MESH WITH INSECT MESH
475

250
LEGEND:
175

STRUCTURE:
1595 1595

100
PRECAST CONCRETE FOR WALLS & SLABS CEMENT SCREED
10 100 250 175 800 1625 250 100
PREFABRICATED COVER SAND GRAVEL MATERIAL

B B GRATING EARTH

LEAN CONCRETE FENCE

IN SITU REINFORCED CONCRETE SAND / GRAVEL

PLAN 1-1 PLAN 2-2 SELECTED BEDDING MATERIAL

SCALE 1:20 SCALE 1:20

ALL CONCRETE STRUCTURES WITH A FLOOR LEVEL BELOW PERMANENT
TANKING: GRADE SHALL HAVE THE UNDERGROUND PART COMPLETELY ENCASED
IN A TANKING MADE FROM PREFABRICATED HEAVY DUTY WATER PROOFING
MEMBRANE OF MODIFIED BITUMEN, MINIMUM 4 MM THICK AND WITH A POLYESTER
NON-WOVEN FABRIC BASE. THE TANKING ON THE SIDES AND THE
TOPS OF THE STRUCTURES SHALL BE FULLY TORCH-APPLIED ON A
BITUMEN-PRIMED SURFACE. THE PROTECTION MATERIAL SHALL CONTINUE TO A
LEVEL NOT LESS THAN 0.2M ABOVE FINAL GRADE (STATION ELEVATION). THE TANKING
UNDER THE STRUCTURES SHALL BE LAID ON A CONCRETE BLINDING AND PROTECTED
BY A CONCRETE OVERLAY OF MINIMUM 50 MM THICKNESS. ALL OVERLAPS SHALL BE
MINIMUM 100 MM AND FULLY TORCH-WELDED. PROTECTION MEMBRANE FOR
VERTICAL ELEMENTS SHALL BE PROVIDED BY 4MM THICK BITUMAT.

MOT ROW
LOCKABLE MANHOLE COVER, WATERTIGHT,
SUITABLE FOR TRAFFIC LOAD SLW600 (70t)
PREFABRICATED COVER REMOVABLE LOCKABLE MANHOLE COVER,
PREFABRICATED COVER SLAB CT 06 WATERTIGHT, SUITABLE FOR
2400
1 3200
TRAFFIC LOAD SLW600 (70t)
1
250
250 1800 250 2600 250

MIN. 800 MM
50 50 50 50
250 825 800 425 250 1625 800 425 AERATION PIPE Ø60 STAINLESS
STEEL WITH INSECT MESH

SELECTED BEDDING MATERIAL REFERENCE DRAWING:

HIGHEST SLAB JOINT CT 08
PREFABRICATED COVER REMOVABLE BACKFILL LEVEL
PREFABRICATED COVER SLAB CT 06 DRAWING No. TITLE

10-QP10-P-001 TI-RNGL GENERAL PLOT PLAN

240
90-ZG21-R-002 TYPICAL DRAIN STATION, STATIC DESIGN CALCULATION

20
90-ZG21-V-002 TYPICAL DRAIN STATION, FORMWORK DRAWING

420
825 800 1300 325 800

60
175

60
2 175
2 90-ZG21-W-002 TYPICAL DRAIN STATION, REINFORCEMENT DRAWING
1220

1220
90-ZG21-L-002 TYPICAL DRAIN STATION, REINFORCEMENT LIST

CT 11 CT 11 CT 12 ENGINEER'S STAMP: CONTRACTOR'S STAMP:

60
RR DOCUMENT COMMENT SHEET
SAND GRAVEL
GALVANIZED STEEL LADDER,ACC.TO BS4211 OR MATERIAL No. 90-ZG21-S-012 No. WT-SC-D-278
AN EQUIVALENT STANDARD,ENCASED IN CONCRETE
GALVANIZED STEEL LADDER,ACC.TO BS4211 OR Rev. A Date 09/12/2024
AN EQUIVALENT STANDARD,ENCASED IN CONCRETE STATUS A: Approved for construction (AFC)
B: Approved as noted (AAN)
SELECTED BEDDING
D: For Information only (INF)
VARIABLE

VARIABLE
MATERIAL CT 11

℄ ℄ MAIN PIPE 12''

VARIABLE

VARIABLE
MAIN PIPE 12''
TANKING CT 05
WELDOLET
MIN.300 MM
300

PRE-FABRICATED WALL PRE-FABRICATED

AND BOTTOM FRAME 325 305 219 155 WALL AND BOTTOM FRAME
VARIABLE

02 06 03 02 0 ISSUED FOR CONSTRUCTION W.A M.O A.Y 14.12.2024

CEMENT GROUT 01 CEMENT GROUT
A ISSUED FOR APPROVAL W.A M.O A.Y 21.10.2024
590 04
TANKING CT 05 SLOPE MIN. 1% > WALL PROTECTION PLATE REV. ISSUED FOR BY CHECKED APPROVED DATE
1000x1000 mm THICKNESS 6 mm
05 BLIND FLANGE
GALVANIZED GRATING
110 2" #300
60

UPN-100 WITH U-BOLT

STEEL SUPPORT UPN-100 WITH U-BOLT
GALVANIZED GRATING Project No.
608

608
L-PROFILE (BOLTED) STEEL SUPPORT
1340

1340
L-PROFILE (BOLTED)
VARIABLE WC230098
SLOPE 2% ► WALL DUCT WATERTIGHT
SLOPE 2% ►
100

100
SLOPE SCREED MIN. 25 mm
LAID IN FORM WORK CT 10
SUMP

SUMP
500

500
LEAN CONCRETE
LEAN CONCRETE SAUDI WATER AUTHORITY
400

400
500

500
SLOPE SCREED MIN. 25 mm

100
100

SUMP
PIPING MATERIAL SUMP

ITEM QTY
350 979 271 550 350 DESCRIPTION SIZE CLASS FLANGE STD. UNIT 350 1779 271 550 350
NO SAUDI ARABIAN OIL COMPANY (ARAMCO)
400 1800 350 50 1 PIPE, CS ASTM A53 Gr. B, SCH XS 2" - - * m 400 2600 350 50
LOCATION
BALL VALVE, CS ASTM A2016 Gr. WCB,
2 2" #300 ASME B16.5 2 PC JUBAIL RIYAS NGL WATER TRANSMISSION SYSTEM
FLANGED
SECTION B-B FLANGE WN, CS ASTM A105, RAISED SECTION A-A
3 2" #300 ASME B16.5 1 PC
FACE
SCALE 1:20 FLANGE BLIND, CS ASTM A105, RAISED
SCALE 1:20 SAWAED GENERAL CONTRACTING COMPANY
4 2" #300 ASME B16.5 1 PC
FACE RIYAS NGL TIE-IN STATION
ELBOW, LONG RADIUS, CS ASTM A53 TYPICAL DRAIN STATION
5 Gr.B, SCH XS 2" - - 1 PC SCALE
GUIDE DRAWING
WELDOLET, CS ASTM A105, SCH STD x
6 12"x2" - - 1 PC
SCH XS 1:25 DRAWING NO. SHEET REV.

* DEPEND ON SITE CONDITION 9 0 - Z G 2 1 - S - 0 1 2 2/3 0

FINAL
T-B-L Engineering e.U.
ENGINEERING
 GRAPHIC SCALE IN METERS: LEVEL INDICATION:

SECTION PLAN
0 0.5 1
1:15
0 0.5 1
1:10

PREFABRICATED COVER SLAB TYPE 1 PREFABRICATED COVER SLAB TYPE 3 TANKING DETAIL PREFABRICATED COVER SLAB CT 06 NOTES:

SCALE 1:15 SCALE 1:15 SCALE 1:10 SCALE 1:10 1. PIPE PRESSURE RATING ACCORDING TO WALL THICKNESS DETERMINATION REPORT.
2. ALL STATIONS WILL BE PROPERLY MARKED WITH PERMANENT IDENTIFICATION MARKS &SEQUENTIAL NUMBERS.
3. BEFORE PLACING OF THE LEAN CONCRETE UNDER THE FOUNDATIONS, THE CONTRACTOR WILL ENSURE THAT THE
UNDERLYING SOIL HAS BEEN COMPACTED TO MEET THE REQUIREMENTS OF PROJECT SPECIFICATIONS.

C LIFTING DEVICE (PFEIFER

COVER CAP OR EQUIVALENT)
REMOVABLE PREFABRICATED
COVER SLAB
4.
5.
6.
SHAFT BEDDED ON WELL COMPACTED GRAVEL FILL TO PREVENT ANY LOAD BEING TRANSFERRED TO THE PIPELINE.
FOR THE LOCATION OF STATIONS REFER TO THE PIPELINE ALIGNMENT SHEETS.
ALL EMBEDDED STEEL ITEMS ARE HOT DIP GALVANIZED.
1595 7. ALL CORNERS ARE TO BE CHAMFERED TO 20mm.
8. BACKFILLING SHALL BE DONE IN UNIFORM LAYERS OF 0.25m THICKNESS. BACKFILL SHALL BE COMPACTED TO AT

CONCRETE OVERLAY LEAST 95% PROCTOR DENSITY.

VAR
175 1245 175 1595
9. THIS DRAWING IS FOR GENERAL ARRANGEMENT ONLY.
10. ALL DIMENSIONS ARE IN MILLIMETERS, ELEVATIONS ARE IN METERS.
11. PIPES, FITTINGS, FLANGES, BOLTINGS AND GASKETS INSIDE STATION SHALL FULFILL REQUIREMENTS OF DOC. No.
HEAVY DUTY WATER PROOFING MEMBRANE
QC10-H-048 SPECIFICATION M08: PIPING MATERIALS FOR STATIONS.

20
OF MODIFIED BITUMEN MIN. 4 mm THICK
175

175
12. THE INTERNAL LINING OF PIPES, FITTINGS, AND OTHER PIPING COMPONENTS INSIDE DRAIN STATION SHALL BE
LIFTING DEVICE CT 07 BLINDING CONCRETE PERMANENTLY MASTIC NEOPRENE 15CM DONE WITH FUSION BONDED EPOXY ACC. TO DOC. No. QC10-H-060 SPECIFICATION M20: FUSION-BONDED EPOXY
LAYER JOINT SEAL WIDE LINING.
13. THE EXTERNAL COATING OF PIPES, FITTINGS AND OTHER PIPING COMPONENTS INSIDE DRAIN STATION SHALL BE
815

STYROFOAM BACKING SHAFT INSIDE

D D LIFTING DEVICE CT 07
ROD DONE ACC. TO DOC. No. QC10-H-061 SPECIFICATION M21: PAINTING OF PIPING, EQUIPMENT AND STRUCTURAL
STEELWORK.
50
950

950
14. THE COATING OF BURIED JOINTS, FITTINGS AND OTHER PIPING COMPONENTS INSIDE DRAIN STATION SHALL BE
SLAB TYPE 1 AERATION PIPE CT 09
DONE WITH HEAT SHRINKABLE SLEEVES ACC. TO DOC. No. QC10-H-062 SPECIFICATION M22: LIQUID-EPOXY COATING.
SLAB TYPE 3 15. FENCING TO BE PROVIDED FOR DRAIN STATION EXCEPT WITHIN MOT-ROW.
MINIMUM DISTANCE BETWEEN SHAFT AND FENCE SHALL BE 1,0m DEPENDING ON LOCAL SITE CONDITIONS.
PUMP SUMP
FENCING CONSISTS OF 3,0m HIGH WIRE MESH FENCE.
875 720 16. THE AERATION PIPES TO BE ROUTED UNDERGROUND TO EDGE OF ROW IF ARRANGED WITHIN MOT-ROW
2400

2400
LEGEND:
LIFTING DEVICE CT 07
800

800
PUMP SUMP
DETAIL JOINT SEALING FOR TOP SLAB PRECAST STRUCTURE:
SCALE 1:10 CONCRETE ELEMENTS FOR SHAFTS CT 08 PRECAST CONCRETE FOR WALLS & SLABS CEMENT SCREED

PREFABRICATED COVER SAND GRAVEL MATERIAL

SCALE 1:10 GRATING EARTH
ANCHOR BAR: BST 500 S OR STAINLESS STEEL
300

300
LEAN CONCRETE FENCE
SOCKET: GALVANIZED OR STAINLESS STEEL 320 S 31
IN SITU REINFORCED CONCRETE SAND / GRAVEL

COVER SLAB SELECTED BEDDING MATERIAL

20
LIFTING DEVICE (PREFER MASTIC SEALING COMPOUND WITH

15
SOCKET OR EQUIVALENT) BACKING ROD

175
175

300 800 145 175 300 800 TANKING:

ALL CONCRETE STRUCTURES WITH A FLOOR LEVEL BELOW PERMANENT

250
175 145 175 GRADE SHALL HAVE THE UNDERGROUND PART COMPLETELY ENCASED
IN A TANKING MADE FROM PREFABRICATED HEAVY DUTY WATER PROOFING
MEMBRANE OF MODIFIED BITUMEN, MINIMUM 4 MM THICK AND WITH A POLYESTER

175 NON-WOVEN FABRIC BASE. THE TANKING ON THE SIDES AND THE
TOPS OF THE STRUCTURES SHALL BE FULLY TORCH-APPLIED ON A

C FOR EXACT TYPE & LIFTING CAPACITY

10
BITUMEN-PRIMED SURFACE. THE PROTECTION MATERIAL SHALL CONTINUE TO A
LEVEL NOT LESS THAN 0.2M ABOVE FINAL GRADE (STATION ELEVATION). THE TANKING
UNDER THE STRUCTURES SHALL BE LAID ON A CONCRETE BLINDING AND PROTECTED
BY A CONCRETE OVERLAY OF MINIMUM 50 MM THICKNESS. ALL OVERLAPS SHALL BE
REFER TO CONSTRUCTION DRAWINGS MINIMUM 100 MM AND FULLY TORCH-WELDED. PROTECTION MEMBRANE FOR
VERTICAL ELEMENTS SHALL BE PROVIDED BY 4MM THICK BITUMAT.

PREFABRICATED COVER SLAB TYPE 2 PREFABRICATED COVER SLAB TYPE 4

SCALE 1:15 SCALE 1:15
CT 09 CT 10
175 1245 175 175 1245 175 SCALE 1:10 SCALE 1:10
AERATION PIPE TYPICAL WALL DUCT WATERTIGHT
175

175

(LAID IN FORMWORK) AT EXTERNAL WALL PIPE-PASSAGES

LIFTING DEVICE CT 07
R150 (WITH FLUSH STEEL DUCT PIPE)
815

STAINLESS STEEL STAINLESS STEEL

LIFTING DEVICE CT 07 INSECT MESH PIPE DN 100
AERATION PIPE CT 09
REFERENCE DRAWING:
ADAPT POSSIBLE 3 THK PUDDLE FLANGE

150
EXTERNAL TANKING DRAWING No. TITLE
COVER SLAB
POLYURETHANE FOAM 10-QP10-P-001 TI-RNGL GENERAL PLOT PLAN
90-ZG21-R-002 TYPICAL DRAIN STATION, STATIC DESIGN CALCULATION
875 720 90-ZG21-V-002 TYPICAL DRAIN STATION, FORMWORK DRAWING
2050

2400

2050

2400

STEEL DUCT PIPE WITH

90-ZG21-W-002 TYPICAL DRAIN STATION, REINFORCEMENT DRAWING
90-ZG21-L-002 TYPICAL DRAIN STATION, REINFORCEMENT LIST
SLAB TYPE 4

PLATE FLANGE
SLAB TYPE 2

DRAIN PIPE
COLLAR FIXATION ENGINEER'S STAMP: CONTRACTOR'S STAMP:
150
SHAFT INSIDE RR DOCUMENT COMMENT SHEET
No. 90-ZG21-S-012 No. WT-SC-D-278
Rev. A Date 09/12/2024
STATUS A: Approved for construction (AFC)
B: Approved as noted (AAN)

PLAN VIEW D: For Information only (INF)

175

175

SHAFT OUTSIDE SHAFT INSIDE

1595 WALL
0 ISSUED FOR CONSTRUCTION W.A M.O A.Y 14.12.2024
THICKNESS A ISSUED FOR APPROVAL W.A M.O A.Y 21.10.2024

REV. ISSUED FOR BY CHECKED APPROVED DATE

PREFABRICATED COVER SLAB SECTION C-C PREFABRICATED COVER SLAB SECTION D-D
Project No.
SCALE 1:15 SCALE 1:15
CT 11 CT 12 WC230098

AERATION PIPE
AERATION PIPE
SCALE 1:10 SCALE 1:10
PRECAST CONCRETE TYPICAL WALL PENETRATION WITH
PUDDLE FLANGE ONLY FOR AERATION PIPE SAUDI WATER AUTHORITY
ELEMENT SOCKET
250

250

PUDDLE FLANGE Ø60

TANKING WALL SURFACE
FAIR FINISHED
STYROFOAM
815 310 800 475 875 720 BACKING ROD
HARD RUBBER WELD BETWEEN PUDDLE SAUDI ARABIAN OIL COMPANY (ARAMCO)
PERMANENTLY ELASTIC BEARING STRIP FLANGE AND AERATION PIPE
2400 1595 SEALING COMPOUND LOCATION
20

JUBAIL RIYAS NGL WATER TRANSMISSION SYSTEM

70

HARD RUBBER
BEARING STRIP
AERATION PIPE Ø 60 SAWAED GENERAL CONTRACTING COMPANY
OUTSIDE INSIDE

TANKING
RIYAS NGL TIE-IN STATION
80 120 SCALE
TYPICAL DRAIN STATION
50 SHAFT INSIDE SHAFT OUTSIDE GUIDE DRAWING

250
1:10 &1:15 DRAWING NO. SHEET REV.
WALL 9 0 - Z G 2 1 - S - 0 1 2 3/3 0
THICKNESS
FINAL
T-B-L Engineering e.U.
ENGINEERING