Internal Use Only

North/Latin America http://aic.lgservice.com

Europe/Africa http://eic.lgservice.com
Asia/Oceania http://biz.lgservice.com

LED TV
SERVICE MANUAL
CHASSIS : LD46W

MODEL : 28LF49** 28LF49**-Z*

CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : MFL69194202 (1504-REV00) Printed in Korea

 CONTENTS

CONTENTS ............................................................................................... 2

SAFETY PRECAUTIONS ......................................................................... 3

SERVICING PRECAUTIONS..................................................................... 4

SPECIFICATION........................................................................................ 6

ADJUSTMENT INSTRUCTION............................................................... 10

BLOCK DIAGRAM .................................................................................. 19

EXPLODED VIEW ................................................................................... 20

SCHEMATIC CIRCUIT DIAGRAM ............................................ APPENDIX

Copyright © LG Electronics. Inc. All rights reserved. -2- LGE Internal Use Only
Only for training and service purposes
 SAFETY PRECAUTIONS

IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

General Guidance Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC Do not use a line Isolation Transformer during this check.
power line. Use a transformer of adequate power rating as this Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor
protects the technician from accidents resulting in personal injury between a known good earth ground (Water Pipe, Conduit, etc.)
from electrical shocks. and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
It will also protect the receiver and it's components from being with 1000 ohms/volt or more sensitivity.
damaged by accidental shorts of the circuitry that may be Reverse plug the AC cord into the AC outlet and repeat AC voltage
inadvertently introduced during the service operation. measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
If any fuse (or Fusible Resistor) in this TV receiver is blown, 0.5 mA.
replace it with the specified. In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
When replacing a high wattage resistor (Oxide Metal Film Resistor, repaired before it is returned to the customer.
over 1 W), keep the resistor 10 mm away from PCB.
Leakage Current Hot Check circuit
Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed

metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1 MΩ and 5.2 MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.

Copyright © LG Electronics. Inc. All rights reserved. -3- LGE Internal Use Only
Only for training and service purposes
 SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service 2. After removing an electrical assembly equipped with ES
manual and its supplements and addenda, read and follow the devices, place the assembly on a conductive surface such as
SAFETY PRECAUTIONS on page 3 of this publication. aluminum foil, to prevent electrostatic charge buildup or expo-
NOTE: If unforeseen circumstances create conflict between the sure of the assembly.
following servicing precautions and any of the safety precautions 3. Use only a grounded-tip soldering iron to solder or unsolder ES
on page 3 of this publication, always follow the safety precautions. devices.
Remember: Safety First. 4. Use only an anti-static type solder removal device. Some solder
removal devices not classified as “anti-static” can generate
General Servicing Precautions electrical charges sufficient to damage ES devices.
1. Always unplug the receiver AC power cord from the AC power 5. Do not use freon-propelled chemicals. These can generate
source before; electrical charges sufficient to damage ES devices.
a. Removing or reinstalling any component, circuit board mod- 6. Do not remove a replacement ES device from its protective
ule or any other receiver assembly. package until immediately before you are ready to install it.
b. Disconnecting or reconnecting any receiver electrical plug or (Most replacement ES devices are packaged with leads electri-
other electrical connection. cally shorted together by conductive foam, aluminum foil or
c. Connecting a test substitute in parallel with an electrolytic comparable conductive material).
capacitor in the receiver. 7. Immediately before removing the protective material from the
CAUTION: A wrong part substitution or incorrect polarity leads of a replacement ES device, touch the protective material
installation of electrolytic capacitors may result in an explo- to the chassis or circuit assembly into which the device will be
sion hazard. installed.
2. Test high voltage only by measuring it with an appropriate CAUTION: Be sure no power is applied to the chassis or circuit,
high voltage meter or other voltage measuring device (DVM, and observe all other safety precautions.
FETVOM, etc) equipped with a suitable high voltage probe. 8. Minimize bodily motions when handling unpackaged replace-
Do not test high voltage by "drawing an arc". ment ES devices. (Otherwise harmless motion such as the
3. Do not spray chemicals on or near this receiver or any of its brushing together of your clothes fabric or the lifting of your
assemblies. foot from a carpeted floor can generate static electricity suf-
4. Unless specified otherwise in this service manual, clean ficient to damage an ES device.)
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable General Soldering Guidelines
non-abrasive applicator; 10 % (by volume) Acetone and 90 % 1. Use a grounded-tip, low-wattage soldering iron and appropriate
(by volume) isopropyl alcohol (90 % - 99 % strength) tip size and shape that will maintain tip temperature within the
CAUTION: This is a flammable mixture. range or 500 °F to 600 °F.
Unless specified otherwise in this service manual, lubrication of 2. Use an appropriate gauge of RMA resin-core solder composed
contacts in not required. of 60 parts tin/40 parts lead.
5. Do not defeat any plug/socket B+ voltage interlocks with which 3. Keep the soldering iron tip clean and well tinned.
receivers covered by this service manual might be equipped. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
6. Do not apply AC power to this instrument and/or any of its bristle (0.5 inch, or 1.25 cm) brush with a metal handle.
electrical assemblies unless all solid-state device heat sinks are Do not use freon-propelled spray-on cleaners.
correctly installed. 5. Use the following unsoldering technique
7. Always connect the test receiver ground lead to the receiver a. Allow the soldering iron tip to reach normal temperature.
chassis ground before connecting the test receiver positive (500 °F to 600 °F)
lead. b. Heat the component lead until the solder melts.
Always remove the test receiver ground lead last. c. Quickly draw the melted solder with an anti-static, suction-
8. Use with this receiver only the test fixtures specified in this type solder removal device or with solder braid.
service manual. CAUTION: Work quickly to avoid overheating the circuit
CAUTION: Do not connect the test fixture ground strap to any board printed foil.
heat sink in this receiver. 6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
Electrostatically Sensitive (ES) Devices (500 °F to 600 °F)
Some semiconductor (solid-state) devices can be damaged eas- b. First, hold the soldering iron tip and solder the strand against
ily by static electricity. Such components commonly are called the component lead until the solder melts.
Electrostatically Sensitive (ES) Devices. Examples of typical ES c. Quickly move the soldering iron tip to the junction of the
devices are integrated circuits and some field-effect transistors component lead and the printed circuit foil, and hold it there
and semiconductor “chip” components. The following techniques only until the solder flows onto and around both the compo-
should be used to help reduce the incidence of component dam- nent lead and the foil.
age caused by static by static electricity. CAUTION: Work quickly to avoid overheating the circuit
1. Immediately before handling any semiconductor component or board printed foil.
semiconductor-equipped assembly, drain off any electrostatic d. Closely inspect the solder area and remove any excess or
charge on your body by touching a known earth ground. Alter- splashed solder with a small wire-bristle brush.
natively, obtain and wear a commercially available discharging
wrist strap device, which should be removed to prevent poten-
tial shock reasons prior to applying power to the unit under test.

Copyright © LG Electronics. Inc. All rights reserved. -4- LGE Internal Use Only
Only for training and service purposes
IC Remove/Replacement 3. Solder the connections.
Some chassis circuit boards have slotted holes (oblong) through CAUTION: Maintain original spacing between the replaced
which the IC leads are inserted and then bent flat against the cir- component and adjacent components and the circuit board to
cuit foil. When holes are the slotted type, the following technique prevent excessive component temperatures.
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique Circuit Board Foil Repair
as outlined in paragraphs 5 and 6 above. Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
Removal board causing the foil to separate from or "lift-off" the board. The
1. Desolder and straighten each IC lead in one operation by following guidelines and procedures should be followed whenever
gently prying up on the lead with the soldering iron tip as the this condition is encountered.
solder melts.
2. Draw away the melted solder with an anti-static suction-type At IC Connections
solder removal device (or with solder braid) before removing To repair a defective copper pattern at IC connections use the
the IC. following procedure to install a jumper wire on the copper pattern
Replacement side of the circuit board. (Use this technique only on IC connec-
1. Carefully insert the replacement IC in the circuit board. tions).
2. Carefully bend each IC lead against the circuit foil pad and
solder it. 1. Carefully remove the damaged copper pattern with a sharp
3. Clean the soldered areas with a small wire-bristle brush. knife. (Remove only as much copper as absolutely necessary).
(It is not necessary to reapply acrylic coating to the areas). 2. carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
"Small-Signal" Discrete Transistor 3. Bend a small "U" in one end of a small gauge jumper wire and
Removal/Replacement carefully crimp it around the IC pin. Solder the IC connection.
1. Remove the defective transistor by clipping its leads as close 4. Route the jumper wire along the path of the out-away copper
as possible to the component body. pattern and let it overlap the previously scraped end of the
2. Bend into a "U" shape the end of each of three leads remaining good copper pattern. Solder the overlapped area and clip off
on the circuit board. any excess jumper wire.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the corresponding At Other Connections
leads extending from the circuit board and crimp the "U" with Use the following technique to repair the defective copper pattern
long nose pliers to insure metal to metal contact then solder at connections other than IC Pins. This technique involves the
each connection. installation of a jumper wire on the component side of the circuit
board.
Power Output, Transistor Device
Removal/Replacement 1. Remove the defective copper pattern with a sharp knife.
1. Heat and remove all solder from around the transistor leads. Remove at least 1/4 inch of copper, to ensure that a hazardous
2. Remove the heat sink mounting screw (if so equipped). condition will not exist if the jumper wire opens.
3. Carefully remove the transistor from the heat sink of the circuit 2. Trace along the copper pattern from both sides of the pattern
board. break and locate the nearest component that is directly con-
4. Insert new transistor in the circuit board. nected to the affected copper pattern.
5. Solder each transistor lead, and clip off excess lead. 3. Connect insulated 20-gauge jumper wire from the lead of the
6. Replace heat sink. nearest component on one side of the pattern break to the lead
of the nearest component on the other side.
Diode Removal/Replacement Carefully crimp and solder the connections.
1. Remove defective diode by clipping its leads as close as pos- CAUTION: Be sure the insulated jumper wire is dressed so the
sible to diode body. it does not touch components or sharp edges.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.

Fuse and Conventional Resistor

Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.

Copyright © LG Electronics. Inc. All rights reserved. -5- LGE Internal Use Only
Only for training and service purposes
 SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.

1. Application range 3. Test method

This specification is applied to the LCD TV used LD46W 1) Performance: LGE TV test method followed
chassis. 2) Demanded other specification
- Safety : CE, IEC specification
- EMC : CE, IEC, CU
2. Requirement for Test
Each part is tested as below without special appointment.

1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C

2) Relative Humidity: 65 % ± 10 %
3) Power Voltage
: Standard input voltage (AC 100-240 V~, 50/60 Hz)
* Standard Voltage of each products is marked by models.
4) Specification and performance of each parts are followed
each drawing and specification by part number in
accordance with BOM.
5) The receiver must be operated for about 20 minutes prior to
the adjustment.

4. Model General Specification

No. Item Specification Remarks
1 Market EU(PAL Market-37Countries) DTV & Analog (Total 37 countries)
DTV (MPEG2/4, DVB-T) : 29 countries
Germany, Netherland, Switzerland, Hungary, Austria, Slov-
enia, Bulgaria, France, Spain, Italy, Belgium, Luxemburg,
Greece, Czech, Croatia, Turkey, Moroco, Ireland, Latvia,
Estonia, Lithuania, Poland, Portugal, Romania, Albania,
Bosnia, Serbia, Slovakia, Beralus

DTV (MPEG2/4, DVB-T2): 8 countries

UK(Ireland), Sweden, Denmark, Finland, Norway, Ukraine,
Kazakhstan, Russia

DTV (MPEG2/4, DVB-C): 37 countries

Germany, Netherland, Switzerland, Hungary, Austria,
Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia,
Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ire-
land, Latvia, Estonia, Lithuania, Poland, Portugal, Romania,
Albania, Bosnia, Serbia, Slovakia, Beralus, UK, Sweden,
Denmark, Finland, Norway, Ukraine, Kazakhstan

DTV (MPEG2/4,DVB-S): 30 countries

Germany, Netherland, Switzerland, Hungary, Austria,
Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia,
Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ire-
land, Latvia, Estonia, Lithuania, Poland, Portugal, Romania,
Albania, Bosnia, Serbia, Slovakia, Beralus

Supported satellite : 22 satellites

HISPASAT 1C/1D, ATLANTIC BIRD 2, NILESAT 101/102,
ATLANTIC BIRD 3, AMOS 2/3, THOR 5/6, IRIUS 4,
EUTELSAT-W3A, EUROBIRD 9A, EUTELSAT-W2A,
HOTBIRD 6/8/9, EUTELSAT-SESAT, ASTRA 1L/H/M/
KR, ASTRA 3A/3B, BADR 4/6, ASTRA 2D, EUROBIRD 3,
EUTELSAT-W7, HELLASSAT 2, EXPRESS AM1, TURK-
SAT 2A/3A, INTERSAT10

Copyright © LG Electronics. Inc. All rights reserved. -6- LGE Internal Use Only
Only for training and service purposes
 No. Item Specification Remarks
1) PAL-BG
2) PAL-DK
MODEL NAME
3) PAL-I
SW/IS/AG/UK : T2/C/S2 - FHD “V”, HD “U”
4) SECAM-L/L', DK , BG, I
2 Broadcasting system DG/BN : T2/C/S2 - FHD “9”, HD “7”
5) DVB-T
T/C – FHD “8”, HD “6”
6) DVB-C
Rest of Europe : T2/C/S2 - FHD “W”, HD “P”
7) DVB-T2
8) DVB-S/S2
1 ) Digital TV
- VHF, UHF
- C-Band,Ku-Band
2) Analogue TV
3 Program coverage
- VHF : E2 to E12
- UHF : E21 to E69
- CATV : S1 to S20
- HYPER : S21 to S47
► DVB-T
- Guard Interval(Bitrate_Mbit/s)
1/4, 1/8, 1/16, 1/32
- Modulation : Code Rate
QPSK : 1/2, 2/3, 3/4, 5/6, 7/8
16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8

► DVB-T2 (Model : *L*V*-Z* (T2 only Model))

- Guard Interval(Bitrate_Mbit/s)
1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256,
- Modulation : Code Rate
QPSK : 1/2, 2/5, 2/3, 3/4, 5/6
Analog : Upper Heterodyne 16-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
4 Receiving system
Digital : COFDM, QAM 64-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
256-QAM : 1/2, 2/5, 2/3, 3/4, 5/6

► DVB-C
- Symbolrate : 4.0Msymbols/s to 7.2Msymbols/s
- Modulation : 16QAM, 64-QAM, 128-QAM and 256-QAM

► DVB-S/S2
- symbolrate
DVB-S2 (8PSK / QPSK) : 2 ~ 45Msymbol/s
DVB-S (QPSK) : 2 ~ 45Msymbol/s
- viterbi
DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8
DVB-S2 mode : 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10
Scart 1 Jack is Full scart and support ATV/DTV-OUT
5 Scart (1EA) PAL, SECAM
(not support DTV Auto AV)
4 System : PAL, SECAM, NTSC4.43, PAL60
6 Video Input RCA(1EA) PAL, SECAM, NTSC4.43
Hybrid Type
Antenna, AV1, Component, HDMI1,
7 Head phone out
HDMI2, USB1, USB2
Y/Cb/Cr
8 Component Input (1EA) Hybrid Type
Y/Pb/Pr
HDMI1-DTV HDMI1: PC support(HDMI version 1.3)
9 HDMI Input (2EA)
HDMI2-DTV Support HDCP
DVI Audio
10 Audio Input (3EA) Component/AV L/R Input.
Scart
11 SDPIF out (1EA) SPDIF out
12 USB (1EA) EMF, DivX HD, For SVC (download) JPEG, MP3, DivX HD
13 Ethernet Connect(1EA) Ethernet Connect

Copyright © LG Electronics. Inc. All rights reserved. -7- LGE Internal Use Only
Only for training and service purposes
5. Component Video Input (Y, Pb, Pr)
No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock
1. 720×480 15.73 60.00 SDTV, DVD 480i
2. 720×480 15.63 59.94 SDTV, DVD 480i
3. 720×480 31.47 59.94 480p
4. 720×480 31.50 60.00 480p
5. 720×576 15.625 50.00 SDTV, DVD 625 Line
6. 720×576 31.25 50.00 HDTV 576p
7. 1280×720 45.00 50.00 HDTV 720p
8. 1280×720 44.96 59.94 HDTV 720p
9. 1280×720 45.00 60.00 HDTV 720p
10. 1920×1080 31.25 50.00 HDTV 1080i
11. 1920×1080 33.75 60.00 HDTV 1080i
12. 1920×1080 33.72 59.94 HDTV 1080i
13. 1920×1080 56.250 50 HDTV 1080p
14. 1920×1080 67.5 60 HDTV 1080p

Copyright © LG Electronics. Inc. All rights reserved. -8- LGE Internal Use Only
Only for training and service purposes
6. HDMI Input
6.1. DTV mode
No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz)
1 640*480 31.469 / 31.5 59.94/60 SDTV 480P
2 720*480 31.469 / 31.5 59.94 / 60 SDTV 480P
3 720*576 31.25 50 SDTV 576P
4 720*576 15.625 50 SDTV 576I
5 1280*720 37.500 50 HDTV 720P
6 1280*720 44.96 / 45 59.94 / 60 HDTV 720P
7 1920*1080 33.72 / 33.75 59.94 / 60 HDTV 1080I
8 1920*1080 28.125 50.00 HDTV 1080I
9 1920*1080 26.97 / 27 23.97 / 24 HDTV 1080P
10 1920*1080 28.125 25 HDTV 1080P
11 1920*1080 33.716 / 33.75 29.976 / 30.00 HDTV 1080P
12 1920*1080 56.250 50 HDTV 1080P
13 1920*1080 67.43 / 67.5 59.94 / 60 HDTV 1080P

6.2. PC mode
No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Remarks
1 640 x 350 @70Hz 31.468 70.09 EGA
2 720 x 400 @70Hz 31.469 70.08 DOS
3 640 x 480 @60Hz 31.469 59.94 VESA(VGA)
4 800 x 600 @60Hz 37.879 60.31 VESA(SVGA)
5 1024 x 768 @60Hz 48.363 60.00 VESA(XGA)
6 1152 x 864 @60Hz 54.348 60.053 VESA
7 1280 x 1024 @60Hz 63.981 60.020 VESA(SXGA) FHD model only
8 1360 x 768 @60Hz 47.712 60.015 VESA(WXGA)
9 1920 x 1080 @60Hz 67.5 60.00 WUXGA(Reduced Blanking) FHD model only

Copyright © LG Electronics. Inc. All rights reserved. -9- LGE Internal Use Only
Only for training and service purposes
 ADJUSTMENT INSTRUCTION
1. Application Range 3.2. LAN Inspection
This specification sheet is applied to all of the LED LCD TV 3.2.1. Equipment & Condition
with LD46W chassis. ▪ Each other connection to LAN Port of IP Hub and Jig

2. Designation
(1) Because this is not a hot chassis, it is not necessary to
use an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
25 °C ± 5 °C of temperature and 65 % ± 10 % of relative
humidity if there is no specific designation.
3.2.2. LAN inspection solution
▪ LAN Port connection with PCB
(4) The input voltage of the receiver must keep AC 100-240
▪ Setting automatic IP
V~, 50/60 Hz.
(5) The receiver must be operated for about 5 minutes prior to
the adjustment when module is in the circumstance of over
15.

In case of keeping module is in the circumstance of 0 °C, it

should be placed in the circumstance of above 15 °C for 2
hours.

In case of keeping module is in the circumstance of below

▪ If you want manual connection, enter Network connection at
-20 °C, it should be placed in the circumstance of above 15
MENU Mode of TV. Press Start connection key, then
°C for 3 hours.
Network will be connected.
[Caution]
When still image is displayed for a period of 20 minutes or
longer (Especially where W/B scale is strong. Digital pattern
13ch and/or Cross hatch pattern 09ch), there can some
afterimage in the black level area.

3. Automatic Adjustment
3.1. MAC address D/L, CI+ key D/L, Widevine
key D/L, ESN D/L, HDCP14/20 D/L
Connect: USB port
Communication Prot connection
▪ Com 1,2,3,4 and 115200(Baudrate)
Mode check: Online Only ▪ Setting state confirmation
▪ Check the test process: DETECT → MAC → CI → Widevine - If automatic setting is finished, you confirm IP and MAC
→ ESN → HDCP14 → HDCP20 Address at ‘in start’ menu mode.
▪ Play: Press Enter key
▪ Result: Ready, Test, OK or NG
▪ Printer Out (MAC Address Label)

Copyright © LG Electronics. Inc. All rights reserved. - 10 - LGE Internal Use Only
Only for training and service purposes
3.2.3. WIDEVINE key Inspection 3.3. LAN PORT INSPECTION(PING TEST)
- Confirm key input data at the "IN START" MENU Mode. Connect SET → LAN port == PC → LAN Port
SET PC

3.3.1. Equipment setting

(1) Play the LAN Port Test PROGRAM.
(2) Input IP set up for an inspection to Test Program.
*IP Number : 12.12.2.2

3.3.2. LAN PORT inspection(PING TEST)

(1) Play the LAN Port Test Program.
(2) Connect each other LAN Port Jack.
(3) Play Test (F9) button and confirm OK Message.
(4) Remove LAN cable.

3.2.4. ESN Key Inspection

- Confirm Key input Data at the “IN START” MENU Mode

3.4. Model name & Serial number Download

3.4.1. Model name & Serial number D/L
▪ Press "P-ONLY" key of service remote control.
(Baud rate : 115200 bps)
3.2.5. HDCP 1.4/2.0 Key Inspection ▪ Connect RS-232C Signal to USB Cable to USB.

- Confirm Key input Data at the “IN START” MENU Mode ▪ Write Serial number by use USB port.
▪ Must check the serial number at Instart menu.

3.4.2. Method & notice

(1) Serial number D/L is using of scan equipment.
(2) Setting of scan equipment operated by Manufacturing
Technology Group.
(3) Serial number D/L must be conformed when it is produced
in production line, because serial number D/L is mandatory
by D-book 4.0.

Copyright © LG Electronics. Inc. All rights reserved. - 11 - LGE Internal Use Only
Only for training and service purposes
 * Manual Download (Model Name and Serial Number) 3.6. WIFI MAC ADDRESS CHECK
If the TV set is downloaded by OTA or service man, sometimes (1) Using RS232 Command
model name or serial number is initialized.(Not always)
It is impossible to download by bar code scan, so It need H-freq(kHz) V-freq.(Hz)
Manual download. Transmission [A][I][][Set ID][][20][Cr] [O][K][X] or [NG]
1) Press the "Instart" key of Adjustment remote control.
2) Go to the menu "7.Model Number D/L" like below photo. (2) Check the menu on in-start
3) Input the Factory model name(ex 42LA690V-ZA) or Serial
number like photo.


4) Check the model name Instart menu. → Factory name
displayed.
5) C heck the Diagnostics.(DTV country only) → Buyer
model displayed.

3.5. CI+ Key checking method

- Check the Section 3.1
Check whether the key was downloaded or not at ‘In Start’
menu. (Refer to below).

=> Check the Download to CI+ Key value in LGset.

3.5.1. Check the method of CI+ Key value

(1) Check the method on Instart menu
(2) Check the method of RS232C Command
1) Into the main ass’y mode(RS232: aa 00 00)
CMD 1 CMD 2 Data 0
A A 0 0
2) Check the key download for transmitted command
(RS232: ci 00 10)
CMD 1 CMD 2 Data 0
C I 1 0
3) Result value
- Normally status for download : OKx
- Abnormally status for download : NGx

3.5.2. Check the method of CI+ key value(RS232)

1) Into the main ass’y mode(RS232: aa 00 00)
CMD 1 CMD 2 Data 0
A A 0 0
2) Check the mothed of CI+ key by command
(RS232: ci 00 20)
CMD 1 CMD 2 Data 0
C I 2 0
3) Result value
i 01 OK 1d1852d21c1ed5dcx
CI+ Key Value

Copyright © LG Electronics. Inc. All rights reserved. - 12 - LGE Internal Use Only
Only for training and service purposes
4. Manual Adjustment 4.1.2. 2D HD EDID(HD)
0 1 2 3 4 5 6 7 8 9 A B C D E F
* ADC adjustment is not needed because of OTP(Auto ADC
00 00 FF FF FF FF FF FF 00 1E 6D a b
adjustment)
10 c 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 01 01
4.1. EDID DATA 30 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 36 00 40 84 63 00 00 1E 64 19 00 40 41 00 26 30
4.1.1. 2D EDID(FHD)
50 18 88 36 00 40 84 63 00 00 18 00 00 00 FD 00 3A
60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d
70 d 01 e
80 02 03 25 F1 4E 10 1F 04 93 05 14 03 02 12 20 21
90 22 15 01 29 3D 06 C0 15 07 50 09 57 07 f
A0 f 01 1D 80 18 71 1C 16 20 58 2C 25
B0 00 40 84 63 00 00 9E 01 1D 00 BC 52 D0 1E 20 B8
C0 28 55 40 40 84 63 00 00 1E 8C 0A D0 8A 20 E0 2D
D0 10 10 3E 96 00 40 84 63 00 00 18 02 3A 80 18 71
E0 38 2D 40 58 2C 45 00 40 84 63 00 00 1E 00 00 00
F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e

▪ Reference
- HDMI1 ~ HDMI2
- In the data of EDID, bellows may be different by S/W or
▪ Reference Input mode.
- HDMI1 ~ HDMI2 HEX EDID Table DDC Function
- In the data of EDID, bellows may be different by S/W or 0001 0100 Analog
Input mode. 0001 0100 Digital
ⓐ Product ID
HEX EDID Table DDC Function ⓐ Product ID
0001 0100 Analog ⓑ Serial No: Controlled on production line.
0001 0100 Digital ⓒ Month, Year: Controlled on production line:
ex) Monthly : '01' → '01'
ⓑ Serial No: Controlled on production line. Year : '2014' → '18'
ⓒ Month, Year: Controlled on production line: ⓓ Model Name(Hex): LGTV
ex) Monthly : '01' → '01' Chassis MODEL NAME(HEX)
Year : '2014' → '18' LD33B 00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20
ⓓ Model Name(Hex): LGTV
Chassis MODEL NAME(HEX) ⓔ Checksum(LG TV): Changeable by total EDID data.
LD46S 00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 ⓔ1 ⓔ2 ⓔ3
HDMI1 75 E2 X
ⓔ Checksum(LG TV): Changeable by total EDID data.
HDMI2 75 D2 X
ⓔ1 ⓔ2 ⓔ3
HDMI1 E7 1B X ⓕ Vendor Specific(HDMI)
HDMI2 E7 0B X INPUT MODEL NAME(HEX)
HDMI1 67 03 0C 00 10 00 80 1E
ⓕ Vendor Specific(HDMI)
HDMI2 67 03 0C 00 20 00 80 1E
INPUT MODEL NAME(HEX)
HDMI1 78 03 0C 00 10 00 80 1E
HDMI2 78 03 0C 00 20 00 80 1E

Copyright © LG Electronics. Inc. All rights reserved. - 13 - LGE Internal Use Only
Only for training and service purposes
4.2. White Balance Adjustment ▪ Adj. Map
Applied Model : LD46S Chassis ALL MODELS
4.2.1. Overview
Command Data Range Default
▪ W/B adj. Objective & How-it-works Adj. item
(lower caseASCII) (Hex.) (Decimal)
(1) Objective: To reduce each Panel's W/B deviation
CMD1 CMD2 MIN MAX
(2) How-it-works : When R/G/B gain in the OSD is at 192, it R Gain j g 00 C0 TBD
means the panel is at its Full Dynamic Range. In order to G Gain j h 00 C0 TBD
prevent saturation of Full Dynamic range and data, one B Gain j i 00 C0 TBD
Cool
of R/G/B is fixed at 192, and the other two is lowered to R Cut TBD
find the desired value. G Cut TBD
(3) Adjustment condition : normal temperature B Cut TBD
1) Surrounding Temperature : 25 °C ± 5 °C R Gain j a 00 C0 TBD
2) Surrounding Humidity : 20 % ~ 80 % G Gain j b 00 C0 TBD
B Gain j c 00 C0 TBD
Medium
R Cut TBD
4.2.2. Equipment G Cut TBD
(1) Color Analyzer: CA-210 (LED Module : CH 14) B Cut TBD
(2) Adjustment Computer(During auto adj., RS-232C protocol R Gain j d 00 C0 TBD
is needed) G Gain j e 00 C0 TBD
(3) Adjustment Remote control Warm B Gain j f 00 C0 TBD
(4) Video Signal Generator MSPG-925F 720p/216-Gray R Cut TBD
(Model: 217, Pattern: 78) G Cut TBD
→ Only when internal pattern is not available
▪ Color Analyzer Matrix should be calibrated using CS-1000.
4.2.5. Adj. method
(1) Auto adj. method
4.2.3. Equipment connection MAP 1) Set TV in adj. mode using POWER ON key.
Co lo r Analyzer
2) Zero calibrate probe then place it on the center of the
display.
Probe RS -232C
3) Connect Cable.(RS-232C to USB)
Co m p ut er
4) Select mode in adj. Program and begin adj.
RS -232C
RS -232C 5) When adj. is complete (OK Sign), check adj. status pre
Pat t ern Generat o r mode. (Cool, Medium, Warm)
Signal Source
6) Remove probe and RS-232C cable to complete adj.
* If TV internal pattern is used, not needed ▪ W/B Adj. must begin as start command “wb 00 00” , and
finish as end command “wb 00 ff”, and Adj. offset if need.

4.2.4. Adj. Command (Protocol) All models have to fix G gain(172).

<Command Format>
START 6E A 50 A LEN A 03 A CMD A 00 A VAL A CS STOP
(2) Manual adjustment. method
- LEN: Number of Data Byte to be sent 1) Set TV in Adj. mode using P-Only key.
- CMD: Command 2) Zero Calibrate the probe of Color Analyzer, then place it
- VAL: FOS Data value on the center of LCD module within 10 cm of the surface.
- CS: Checksum of sent data 3) Press ADJ key → EZ adjust using adj. R/C → 7. White-
- A: Acknowledge Balance then press the cursor to the right(key ►).
Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX] (When right key(►) is pressed 204 Gray internal pattern
will be displayed)
▪ RS-232C Command used during auto-adjustment. 4) Adjust Cool modes
RS-232C COMMAND ① Fix the one of R/G/B gain to 192 (default data) and
Explantion
[CMD ID DATA]
decrease the others.
wb 00 00 Begin White Balance adjustment
(If G gain is adjusted over 172 and R and B gain less
wb 00 10 Gain adjustment(internal white pattern)
than 192 , Adjust is O.K.)
wb 00 1f Gain adjustment completed
② If G gain is less than 172, Increase G gain by up to
wb 00 20 Offset adjustment(internal white pattern)
172, and then increase R gain and G gain same
wb 00 2f Offset adjustment completed
amount of increasing G gain.
End White Balance adjustment
wb 00 ff ③ If R gain or B gain is over 255, Readjust G gain less
(internal pattern disappears )
than 172, Conform to R gain is 255 or B gain is 255
Ex) wb 00 00 -> Begin white balance auto-adj. 5) Adjust two modes(Medium / Warm) Fix the one of R/G/B
wb 00 10 -> Gain adj. gain to 192(default data) and decrease the others.
ja 00 ff -> Adj. data 6) Adj. is completed, Exit adjust mode using “EXIT” key on
jb 00 c0 Remote control.
... ▪ If internal pattern is not available, use RF input. In EZ Adj.
... menu 6.White Balance, you can select one of 2 Test-
wb 00 1f → Gain adj. completed pattern: ON, OFF. Default is inner (ON).
*(wb 00 20(Start), wb 00 2f(end)) → Off-set adj. By selecting OFF, you can adjust using RF signal in 206
wb 00 ff → End white balance auto-adj. Gray pattern.

Copyright © LG Electronics. Inc. All rights reserved. - 14 - LGE Internal Use Only
Only for training and service purposes
 * CASE Cool 4.2.6. Reference (White balance Adj. coordinate and
First adjust the coordinate far away from the target color temperature)
value(x, y). ▪ Luminance : 204 Gray
1) x, y > target ▪ Standard color coordinate and temperature using CS-1000
i) Decrease the R, G. (over 26 inch)
2) x, y < target
Coordinate
i) First decrease the B gain, Mode Temp ∆uv
ii) Decrease the one of the others. x y
3) x > target, y < target Cool 0.271 0.270 13000 K 0.0000
i) First decrease B, so make y a little more than the Medium 0.286 0.289 9300 K 0.0000
target.
ii) Adjust x value by decreasing the R. Warm 0.313 0.329 6500 K 0.0000
4) x < target, y > target ▪ Standard color coordinate and temperature using CA-210(CH 14)
i) First decrease B, so make x a little more than the for 28LF49 model ( 10000K module)
target.
Coordinate
ii) Adjust x value by decreasing the G. Mode Temp ∆uv
x y
How to adjust Cool 0.271±0.002 0.270±0.002 13000K 0.0000
1. If G gain is adjusted over 172 and R gain and B Medium 0.286±0.002 0.289±0.002 9300K 0.0000
gain less than 192 , Adjust is O.K.
2. If G gain is less than 172 , increase G gain by up to Warm 0.313±0.002 0.329±0.002 6500K 0.0000
172, and then increase R gain and B gain same ▪ Standard color coordinate and temperature using CA-210(CH 14)
amount of increasing G gain. for 22LF49xx-xx.xxxW model ( only 6500K module : HC215EXN-
3. If R gain or B gain is over 255 , Readjust G gain SLDR*)
less than 172, Conform to R gain is 255 or B gain is
Coordinate
255 Mode Temp ∆uv
x y
* CASE Medium / Warm Cool 0.286±0.002 0.289±0.002 9300K 0.0000
First adjust the coordinate far away from the target Medium 0.295±0.002 0.305±0.002 8000K 0.0000
value(x, y).
1) x, y > target Warm 0.313±0.002 0.329±0.002 6500K 0.0000
i) Decrease the R, G.
2) x, y < target
4.2.7. LED White balance table
i) First decrease the B gain,
- EDGE LED module change color coordinate because of
ii) Decrease the one of the others.
aging time.
3) x > target, y < target
- Apply under the color coordinate table, for compensated
i) First decrease B, so make y a little more than the
aging time.
target.
* Gumi ( March ~ December ) & Global
ii) Adjust x value by decreasing the R
LGD model Which cool temperature is 9300K. ( 22LF49 )
4) x < target, y > target
i) First decrease B, so make x a little more than the Cool med warm
target. x y x y x y
ii) Adjust x value by decreasing the G
spec 286 289 295 305 313 329
▪ Adjustment condition and cautionary items target 290 294 299 310 317 334
1) Lighting condition in surrounding area
* Gumi Winter (only January , February)
Surrounding lighting should be lower 10 lux. Try to
LGD model Which cool temperature is 9300K. ( 22LF49 )
isolate adj. area into dark surrounding.
2) Probe location Aging Cool Medium Warm
: Color Analyzer(CA-210) probe should be within 10 cm NC5.0 time(Min) X y x y x y
and perpendicular of the module surface (80° ~ 100°) Target 286 289 295 305 313 329
1 0-2 299 306 308 322 326 346
2 3-5 297 303 306 319 324 343
3 6-9 295 300 304 316 322 340
4 10-19 293 297 302 313 320 337
5 20-35 290 294 299 310 317 334
6 36-49 288 292 297 308 315 332
7 50-79 287 290 296 306 314 330
8 80-119 286 289 295 305 313 329
9 Over 120 286 289 295 305 313 329

Copyright © LG Electronics. Inc. All rights reserved. - 15 - LGE Internal Use Only
Only for training and service purposes
 *
A UO, INX, Sharp, CSOT, BOE model Which cool 4.5. HDMI ARC Function Inspection
temperature is 13000K. (28LF49)AUO, INX, Sharp, CSOT, (1) Test equipment
BOE model Which cool temperature is 13000K. (28LF49) - Optic Receiver Speaker
Cool med warm - MSHG-600 (SW: 1220 ↑)
- HDMI Cable (for 1.4 version)
x y x y x y
(2) Test method
spec 271 270 286 289 313 329 (1) Insert the HDMI cable to the HDMI ARC port from the
target 278 280 293 299 320 339 master equipment (HDMI1)
Luminance Min Typ Min Typ Min Typ
(cd/m^2) 80 110 80 110 80 110

4.4. Magic Motion Remote control test

- R esults are automatically marked in Instart OSD after
through the AP/Magic Remocon Equipment on the line
(2) Check the sound from the TV Set

(3) Check the Sound from the Speaker or using AV & Optic
TEST program (It’s connected to MSHG-600)

* Remark: Inspect in Power Only Mode and check SW


version in a master equipment

Copyright © LG Electronics. Inc. All rights reserved. - 16 - LGE Internal Use Only
Only for training and service purposes
4.6. Wi-Fi Test 4.7. Option selection per country
Step 1) Turn on TV 4.7.1. Overview
Step 2) Select Network Connection option in Network Menu. - Option selection is only done for models in Non-EU

4.7.2. Method
(1) Press ADJ key on the Adj. R/C, then select Country Group
Meun.
(2) Select Country Group Code 04 or Country Group EU

5. Tool Option selection

▪ Method : Press "ADJ" key on the Adjustment remote control,
then select Tool option.

Step 3) Select Start Connection button in Network Connection.

6. Ship-out mode check(In-stop)
▪ After final inspection, press "IN-STOP" key of the Adjustment
remote control and check that the unit goes to Stand-by
mode.

7. GND and Internal Pressure check

7.1. Method
(1) GND & Internal Pressure auto-check preparation
Step 4) If the system finds any AP like blow PIC, it is working - Check that Power cord is fully inserted to the SET.
well. (If loose, re-insert)
(2) Perform GND & Internal Pressure auto-check
- Unit fully inserted Power cord, Antenna cable and A/V
arrive to the auto-check process.
- Connect D-terminal to AV JACK TESTER
- Auto CONTROLLER(GWS103-4) ON
- Perform GND TEST
- If NG, Buzzer will sound to inform the operator.
- If OK, changeover to I/P check automatically.
(Remove CORD, A/V form AV JACK BOX.)
- Perform I/P test
- If NG, Buzzer will sound to inform the operator.
- If OK, Good lamp will lit up and the stopper will allow the
pallet to move on to next process.
4.7. LNB voltage and 22KHz tone check
(only for DVB-S/S2 model)
▪ Test method
(1) Set TV in Adj. mode using POWER ON. 7.2. Checkpoint
(2) Connect cable between satellite ANT and test JIG. ▪ TEST voltage
(3) Press Yellow key(ETC+SWAP) in Adj Remote control to (1) DQA Test
make LNB on. - GND: AC 1.5 KV/min, Cut off current not exceed 100mA
(4) Check LED light ‘ON’ at 18 V menu. - SIGNAL: AC 3.0 KV/min, Cut off current not exceed 100
(5) Check LED light ‘ON’ at 22 KHz tone menu. mA
(6) Press Blue key(ETC+PIP INPUT) in Adj Remote control (2) Mass Production Line Test
to make LNB off. - GND: AC 1.5 KV/sec, Cut off current not exceed 100 mA
(7) Check LED light ‘OFF’ at 18 V menu. ▪ TEST time: DQA 1min, Mass Production Line 1 sec
(8) Check LED light ‘OFF’ at 22 KHz tone menu. ▪ TEST POINT
- GND TEST = POWER CORD GND & SIGNAL CABLE
▪ Test result METAL GND
(1) After press LNB On key, ‘18 V LED’ and ‘22 KHz tone - Internal Pressure TEST = POWER CORD GND & LIVE &
LED’ should be ON. NEUTRAL
(2) After press LNB OFF key, ‘18 V LED’ and ‘22 KHz tone ▪ LEAKAGE CURRENT: At 0.5 mArms
LED’ should be OFF.

Copyright © LG Electronics. Inc. All rights reserved. - 17 - LGE Internal Use Only
Only for training and service purposes
8. Audio
No. Item Min Typ Max Unit Remark
Audio practical max Out- 4.5 5 6 W
1. put, L/R(Distortion=10% EQ Off
max Output) 6 6.3 6.9 Vrms AVL Off
Clear Voice Off
2. Speaker (8Ω Impedance) 4.5 5 6 W

Measurement condition:
(1) RF input: Mono, 1 KHz sine wave signal, 100 % Modulation
(2) CVBS, Component: 1 KHz sine wave signal 0.5 Vrms

9. USB S/W Download(Service only)

(1) Put the USB Stick to the USB socket
(2) Automatically detecting update file in USB Stick
- If your downloaded program version in USB Stick is
Lower, it didn’t work.
B ut your downloaded version is Higher, USB data is
automatically detecting (Download Version High & Power
only mode, Set is automatically Download)
(3) Show the message “Do not unplug!”.
(4) Updating is starting.
(5) Updating completed, the TV will restart automatically.
(6) If your TV is turned on, check your updated version and
Tool option. (explain the Tool option, next stage)
* If downloading version is more high than your TV have,
TV can lost all channel data. In this case, you have to
channel recover. if all channel data is cleared, you didn’t

have a DTV/ATV test on production line.

* After downloading, have to adjust Tool Option again.

(1) Push "IN-START" key in service remote control.
(2) Select "Tool Option 1" and push "OK" key.
(3) Punch in the number. (Each model has their number)

Copyright © LG Electronics. Inc. All rights reserved. - 18 - LGE Internal Use Only
Only for training and service purposes
Copyright ©
Air/
Cable TUNER X_TAL DDR3 1600 X 16
(A) CI Slot 27MHz (512MB X 2EA)
T/C Without ATV
R P_TS
E P_TS DDR3 1600 X 16
Air/ (256MB X 1EA)
A Cable TUNER A B

Only for training and service purposes

R IF (+/-) T/C Demod
(A)
(H) DEMOD Analog Demod SYSTEM EEPROM
Tuner : I2C 6 P_TS
DVB-S (T2/C/S2) P_TS I2C 5 (256Kb)
TUNER
(S2) USB1 OCP
S (HDD) HDCP EEPROM
1.5A I2C 1
T2/C/S2 Without ATV I USB (16Kb)
D USB2 OCP
DVB-S : I2C 4 E 1.5A eMMC

LG Electronics. Inc. All rights reserved.

LNB (4GB)

HDMI1 FHD/HD 30P

S HDMI LVDS
MHL 1A I HDMI2
SIL1292 MUX
MHL D LGE 2122
MHL : I2C 4 E I2S Out Audio AMP

- 19 -
I2C 1 (NTP7513)
H/P AMP
TI
AV/COMP CVBS/YPbPr

R SCART CVBS/RGB
E
BLOCK DIAGRAM

A IR IR
R OPTIC SPDIF OUT
KEY Joystick KEY SUB
ASSY
LAN ETHERNET WIFI
USB_WIFI

Eye-Q

I2C 3 Sub Micom

(RENESAS R5F1000G)

X_TAL
32.768KHz

LGE Internal Use Only

 EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These
parts are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

400

521

900
540

120
570
571
LV1

800

A31
A10
801

A2
200

500
501

Copyright © LG Electronics. Inc. All rights reserved. - 20 - LGE Internal Use Only
Only for training and service purposes
 IC105
LGE2122[A2_M13]
+1.2V_MTK_CORE

L11 R15
VCCK_1 DVSS_24
N12 T15
+1.2V_MTK_CORE VCCK_2 DVSS_25
P12 U15
+3.3V_NORMAL VDD3V3 +1.2V_MTK_CORE 5600mA VCCK_3 DVSS_26
OPT OPT AG5 V15
60mA VCCK_4 DVSS_27
L501 OPT AH5 W15
BLM18PG121SN1D C527 C535 VCCK_5 DVSS_28
C513 AJ5 Y15
0.1uF 0.1uF VCCK_6 DVSS_29
C514 C517 C523 C520 C532 10uF AK5 AA15
C503 C505 C507 C508 VCCK_7 DVSS_30
10uF 10uF 0.1uF 0.1uF 0.1uF AL5 AB15
10uF 10uF 0.1uF 2.2uF VCCK_8 DVSS_31
AM5 T18
VCCK_9 DVSS_32
AN5 R16
VCCK_10 DVSS_33
AK6 T16
VCCK_11 DVSS_34
AL6 U16
VCCK_12 DVSS_35
AM6 V16
VCCK_13 DVSS_36
AN6 W16
VCCK_14 DVSS_37
M11 Y16
VCCK_15 DVSS_38
N11 AA16
VCCK_16 DVSS_39
P11 AB16
VCCK_17 DVSS_40
R11 R17
VCCK_18 DVSS_41
M12 T17
VCCK_19 DVSS_42
R12 U17
VCCK_20 DVSS_43
L13 V17
VCCK_21 DVSS_44
L14 Y17
+3.5V_ST_WAKE VCCK_22 DVSS_45
VDD3V3 L15 N16
AVDD_33SB VCCK_23 DVSS_46
L17 V18
VCCK_24 DVSS_47
L18 Y18
OPT VCCK_25 DVSS_48
L19 P16
L503 VCCK_26 DVSS_49
BLM18PG121SN1D T11 V19
VCCK_27 DVSS_50
U11 Y19
VCCK_28 DVSS_51
V11 W17
VCCK_29 DVSS_52
OPT W11 AA17
+1.2V_MTK_CORE +1.2V_MTK_AVDD VCCK_30 DVSS_53
L502 Y11 AB17
BLM18PG121SN1D VCCK_31 DVSS_54
L504 AA11 N19
BLM18PG121SN1D VCCK_32 DVSS_55
AB11 AC14
OPT VCCK_33 DVSS_56
AC11 C13
C504 C506 C518 VCCK_34 DVSS_57
R23 K24
0.1uF 0.1uF 10uF VCCK_35 DVSS_58
L12 K25
VCCK_36 DVSS_59
W12 L24
VCCK_37 DVSS_60
V23 M17
VCCK_38 DVSS_61
Y12 M18
VCCK_39 DVSS_62
AF6 M19
VCCK_40 DVSS_63
AG6 P17
VCCK_41 DVSS_64
AH6 P19
VCCK_42 DVSS_65
AJ6 N18
VCCK_43 DVSS_66
AE7 U20
VCCK_44 DVSS_67
POWER_ON/OFF1 AF7 V20
VCCK_45 DVSS_68
AVDD_33SB TP500 AG7 W20
VCCK_46 DVSS_69
IC500 AD8 Y20
+3.5V_ST +3.5V_ST_WAKE VCCK_47 DVSS_70
+3.5V_ST_WAKE AP2121N-3.3TRE1 AE8 AA20
VCCK_48 DVSS_71
AF8 R19
VCCK_49 DVSS_72
VIN 3 2 VOUT AE9 T19
VCCK_50 DVSS_73
Q501 AC10 M20
1 VCCK_51 DVSS_74
PMV48XP AD10 N20
GND VCCK_52 DVSS_75
S

AD11 U21
C512 VCCK_53 DVSS_76
C510 1uF AE10 V21
0.1uF VCCK_54 DVSS_77
10V AF9 W21
G 16V VCCK_55 DVSS_78
AG8 Y21
C502
R502

VCCK_56 DVSS_79
10K

C501 0.1uF AH7 AA21

4.7uF VCCK_57 DVSS_80
ZD500

16V AJ7 P20

5V

10V VCCK_58 DVSS_81

OPT AK7 R20
OPT

VCCK_59 DVSS_82
AL7 T20
+3.3V_NORMAL VCCK_60 DVSS_83
3.3V_EMMC LAN_JACK_POWER AM7 U22
VCCK_61 DVSS_84
AN7 V22
VCCK_62 DVSS_85
L16 W22
VCCK_63 DVSS_86
TP501 V12 Y22
L505 VCCK_64 DVSS_87
BLM18PG121SN1D U12 AA22
1.8K
R501

VCCK_65 DVSS_88
T12 N21
VCCK_66 DVSS_89
AD13 P21
VCCK_67 DVSS_90
C531 AD17 R21
0.1uF VCCK_68 DVSS_91
C AD14 T21
R500 16V VDD3V3 VCCK_69 DVSS_92
10K B Q500 AB12 M22
WOL_CTL VCCK_70 DVSS_93
MMBT3904(NXP) AA12 N22
VCCK_71 DVSS_94
AC12 P22
C500 E VCCK_72 DVSS_95
4.7uF R22
DVSS_96
10V T22
OPT DVSS_97
T9 M21
VCC3IO_C DVSS_98
Y10 AC17
VCC3IO_B_1 DVSS_99
AA10 AA19
VCC3IO_B_2 DVSS_100
D22 M13
VCC3IO_A_1 DVSS_101
E22 M14
VCC3IO_A_2 DVSS_102
M15
DVSS_103
AA13
DVSS_104
AC18 AB13
DVSS_1 DVSS_105
AB21 AA14
DVSS_2 DVSS_106
AB14 AB19
DVSS_3 DVSS_107
N13 D6
DVSS_4 DVSS_108
P13 W19
DVSS_5 DVSS_109
R13 U19
DVSS_6 DVSS_110
T13 N17
DVSS_7 DVSS_111
DECAP FOR SOC (HIDDEN - UCC) DECAP FOR SOC Rework (BOTTOM) U13 L3
DVSS_8 DVSS_112
V13 AB18
DVSS_9 DVSS_113
W13 AA18
DVSS_10 DVSS_114
Y13 W18
DVSS_11 DVSS_115
P18 U18
DVSS_12 DVSS_116
N14 D16
DVSS_13 DVSS_117
P14 AC13
+1.2V_MTK_CORE VDD3V3 DVSS_14 DVSS_118
R14 M16
DVSS_15 DVSS_119
T14 AC20
DVSS_16 DVSS_120
U14 AC22
TP502

DVSS_17 DVSS_121
V14 AD20
TP503

DVSS_18 DVSS_122
W14 Y23
DVSS_19 DVSS_123
Y14 AA23
DVSS_20 DVSS_124
R18 AB23
DVSS_21 DVSS_125
N15 V24
DVSS_22 DVSS_126
P15 W23
DVSS_23 DVSS_127

+1.5V_DDR

OPT
+1.5V_DDR OPT
C539 C541
0.1uF 0.1uF
16V

C509 C511
0.1uF 0.1uF

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MID_MAIN_3 2011.12.09
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 10

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 PLACE AT JACK SIDE

R610
51K
SC_ID SC_ID_SOC
1/16W
1%
EU R613
10K
EU

READY FOR FILTER (EMI)

L611
SC_CVBS_IN SC_CVBS_IN_IF
120-ohm
C607 R604
C601 EU 100pF 75
10pF EU 1%
OPT EU

SC_FB SC_FB_SOC
R609
R608 22
75 EU
1%
EU

PLACE AT MAIN SOC SIDE

R623 100 C615 0.01uF
SC_R SC_R_SOC
C604 EU EU
R605 10pF
75
1% EU
EU

R622 100 C614 0.01uF

SC_G C605 SC_G_SOC
10pF EU EU
R606 EU
75
1%
EU 0 R620 100 C612 0.01uF
SC_COM_SOC
R637 EU
1/16W EU
EU R621 100 C613 0.01uF
SC_B SC_B_SOC
R607
75
1%
C606
10pF
EU EU PLACE AT IC6000
EU EU
R617 100 C616 0.047uF +3.3V_NORMAL
SC_CVBS_IN_IF SC_CVBS_IN_SOC
EU EU EU

C620
1uF
R630
R618 68K
15K EU
SCART_Rout_SOC SCART_Rout

EU
+3.3V_NORMAL EU
C619 R631
330pF EU 100K

C621
50V R628

1uF
R619 EU 68K
15K EU
Close to JACK Close to Main Chip SCART_Lout_SOC SCART_Lout

EU
EU
C618 R629
Close to SOC 330pF 100K
50V
C608 EU
10uF 1608 size For EMI
16V R614
R625 0
SC_L_IN SC_L_IN_SOC
EU 30K 1/16W R635
EU C610 5%
SCART_AMP_R_FB
R601 100pF EU 10K
C602
470K 330pF 50V EU
OPT 50V EU
OPT
C609
R636
10uF 1608 size For EMI
16V R624 SCART_AMP_L_FB
R626 0 10K
SC_R_IN SC_R_IN_SOC EU
EU 30K 1/16W
R602 EU C611 5%
470K 100pF EU
OPT C603
330pF 50V
50V EU
OPT

READY FOR FILTER (EMI)

EU
R600

R616 R615 0
DTV/MNT_V_OUT_SOC C600 C617 DTV/MNT_V_OUT
75 75
1% 1% 220pF 100pF
OPT EU
EU OPT

TU_CVBS TP600

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MID_MAIN_SCART 2011.12.30
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 11

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 DDR_512MB_SS
DDR_512MB_SS

IC701 IC703
+1.5V_DDR
K4B4G1646B-HCK0 K4B4G1646B-HCK0
A_RVREF2
ARA[0-14] +1.5V_DDR
A_RVREF4
A_RVREF1 ARA[0-14] +1.5V_DDR
C713 ARA[0] N3 M8
R706 M8 N3 ARA[0]
1K 0.1uF A0 VREFCA A_RVREF2
VREFCA A0 ARA[1] ARA[1] P7 C735
1% P7 R720
ARA[2] P3 A1 A_RVREF3 1K 0.1uF
A_RVREF1 A1 ARA[2]
P3 A2 1% C705 C707
A2 ARA[3] ARA[3] N2 H1 1uF 10uF
H1 N2 A3 VREFDQ
R707 VREFDQ A3 ARA[4] P8 10V
1K C714 P8 ARA[4]
1% ARA[5] P2 A4 1% R721
0.1uF 1% A4 ARA[5] 240
P2 A5 R716 1K C736
R710 240 A5 ARA[6] ARA[6] R8 L8 1% 0.1uF
L8 R8 A6 ZQ
ZQ A6 ARA[7] ARA[7] R2
R2 +1.5V_DDR
+1.5V_DDR ARA[8] T8 A7
A7 ARA[8]
+1.5V_DDR T8 A8
A8 ARA[9] ARA[9] R3 B2
B2 R3 A9 VDD_1
VDD_1 A9 ARA[10] ARA[10] L7 D9 +1.5V_DDR +1.5V_DDR
D9 L7 A10/AP VDD_2
A_RVREF4 VDD_2 A10/AP ARA[11] ARA[11] R7 G7
C715 G7 R7 A11 VDD_3
R708 0.1uF VDD_3 A11 ARA[12] ARA[12] N7 K2
1K K2 N7 A12/BC VDD_4
1% VDD_4 A12/BC ARA[13] T3 K8 A_RVREF3 C733
K8 T3 ARA[13] C704
ARA[14] A13 VDD_5 R718 0.1uF C745 C751 C753 C755 C754 C702
VDD_5 A13 ARA[14] T7 N1 1K 0.1uF 1uF 10uF
N1 T7 A14 VDD_6 1% 0.1uF 0.1uF 0.1uF 0.1uF
VDD_6 A14 M7 N9 10V
R709 N9 M7 A15 VDD_7
1K C716 VDD_7 A15 R1
1% 0.1uF R1 VDD_8
VDD_8 M2 R9 R719
R9 M2 ARBA0 BA0 VDD_9 1K C734
VDD_9 BA0 ARBA0 N8 1%
N8 ARBA1 0.1uF
ARBA1 ARCLK1 BA1
BA1 M3
M3 ARBA2 BA2
BA2 ARBA2 ARCLK0 A1
A1 VDDQ_1
VDDQ_1 J7 A8
A8 J7 R714 CK VDDQ_2
VDDQ_2 CK R712 100 K7 C1
C1 K7 100 5% CK VDDQ_3
VDDQ_3 CK 5% K9 C9
C9 K9 ARCKE CKE VDDQ_4
VDDQ_4 CKE ARCKE D2
D2 VDDQ_5
VDDQ_5 /ARCLK0 /ARCLK1 L2 E9
E9 L2 /ARCSX CS VDDQ_6
VDDQ_6 CS /ARCS K1 F1
F1 K1 ARODT ODT VDDQ_7
VDDQ_7 ODT ARODT J3 H2
H2 J3 /ARRAS RAS VDDQ_8
VDDQ_8 RAS /ARRAS K3 H9
H9 K3 /ARCAS CAS VDDQ_9
VDDQ_9 CAS /ARCAS L3
L3 /ARWE WE
WE /ARWE J1
J1 NC_1
NC_1 T2 J9
J9 T2 ARREST RESET NC_2
NC_2 RESET ARREST L1
L1 NC_3
NC_3 L9
L9 NC_4
NC_4 F3
F3 ARDQS2 DQSL
DQSL ARDQS0 G3
G3 /ARDQS2 DQSL
DQSL /ARDQS0
C7 A9
A9 C7 ARDQS3 DQSU VSS_1
VSS_1 DQSU ARDQS1 B7 B3 IC703-*3
B3 B7 /ARDQS3 DQSU VSS_2
IC701-*1
H5TQ4G63AFR-PBC
IC703-*1
H5TQ4G63AFR-PBC
IC701-*2
MT41K256M16HA-125:E
IC703-*2
MT41K256M16HA-125:E
IC701-*3
MT41K128M16JT-125:K
MT41K128M16JT-125:K
IC105
VSS_2 DQSU /ARDQS1 E1 LGE2122[A2_M13]
DDR_256MB_MICRON
DDR_512MB_MICRON DDR_256MB_MICRON
DDR_512MB_Hynix DDR_512MB_Hynix DDR_512MB_MICRON N3 M8
E1 VSS_3
N3
P7
A0 VREFCA
M8
N3
P7
A0 VREFCA
M8
N3
P7
A0 VREFCA
M8 N3
P7
A0 VREFCA
M8 N3
P7
A0 VREFCA
M8
P7
P3
A0
A1
VREFCA

VSS_3 E7 G8 P3
A1
A2 P3
A1
A2
P3
A1
A2
P3
A1
A2
P3
A1
A2 N2
A2
A3 VREFDQ
H1

G8 E7 ARDQM2 DML VSS_4

N2
P8
A3 VREFDQ
H1
N2
A3 VREFDQ
H1
N2
P8
A3 VREFDQ
H1 N2
P8
A3 VREFDQ
H1 N2
P8
A3 VREFDQ
H1
P8
A4

VSS_4 DML ARDQM0 ARDQ[16-23] D3 J2

P2
R8
A4
A5
L8
P8
P2
A4
A5
P2
R8
A4
A5
L8
P2
R8
A4
A5
L8
P2
R8
A4
A5
L8
P2
R8
A5
A6 ZQ
L8 +1.5V_DDR
J2 D3 ARDQM3 DMU VSS_5 R2
A6
A7
ZQ R8
R2
A6
A7
ZQ
L8
R2
A6
A7
ZQ
R2
A6
A7
ZQ
R2
A6
A7
ZQ R2
T8
A7
A8
+1.5V_DDR
VSS_5 DMU ARDQM1 J8
T8
R3
A8
A9 VDD_1
B2
T8
R3
A8
B2
T8
R3
A8
A9 VDD_1
B2
T8
R3
A8
A9 VDD_1
B2
T8
R3
A8
A9 VDD_1
B2
R3
L7
A9 VDD_1
B2
D9
J8 VSS_6
L7
A10/AP VDD_2
D9
L7
A9 VDD_1
D9
L7
A10/AP VDD_2
D9 L7
A10/AP VDD_2
D9 L7
A10/AP VDD_2
D9
R7
A10/AP VDD_2
G7
R1 D12
VSS_6 ARDQ[0-7] ARDQ[16] E3 M1
R7
N7
A11 VDD_3
G7
K2
R7
A10/AP
A11
VDD_2
VDD_3
G7
R7
N7
A11 VDD_3
G7
K2
R7
N7
A11 VDD_3
G7
K2
R7
N7
A11 VDD_3
G7
K2
N7
A11
A12/BC
VDD_3
VDD_4
K2

ARDQM0
M1 E3 ARDQ[0] T3
A12/BC VDD_4
K8
N7
T3
A12/BC VDD_4
K2
K8
T3
A12/BC VDD_4
K8 T3
A12/BC VDD_4
K8 T3
A12/BC VDD_4
K8
T3
A13 VDD_5
K8
N1
DDRV_1 ARDQM0
ARDQ[17] DQL0 VSS_7 T7
A13
A14
VDD_5
VDD_6
N1
T7
A13 VDD_5
N1
A13 VDD_5
VDD_6
N1
A13 VDD_5
VDD_6
N1
A13 VDD_5
VDD_6
N1
M7
VDD_6
N9 R2 D14
VSS_7 DQL0 ARDQ[1] F7 M9
M7
A15 VDD_7
N9
R1
M7
A14
A15
VDD_6
VDD_7
N9
M7
NC_5 VDD_7
N9
R1
M7
NC_5 VDD_7
N9
R1
M7
NC_5 VDD_7
N9
R1
NC_5 VDD_7
VDD_8
R1
RVREF_A C746 DDRV_2 ARDQS0 ARDQS0
M9 F7 DQL1 VSS_8 M2
BA0
VDD_8
VDD_9
R9
M2
VDD_8
R1
R9
M2
BA0
VDD_8
VDD_9
R9 M2
BA0
VDD_8
VDD_9
R9 M2
BA0
VDD_8
VDD_9
R9
M2
N8
BA0 VDD_9
R9

R730 R3 C14
VSS_8 DQL1 ARDQ[18] F2 P1
N8
BA1 N8
BA0 VDD_9 N8
BA1
N8
BA1
N8
BA1 M3
BA1
0.1uF /ARDQS0 ARDQ[0-7]
P1 F2 ARDQ[2] M3
BA2
A1
M3
BA1
BA2
M3
BA2
A1
M3
BA2
A1
M3
BA2
A1
BA2
VDDQ_1
A1
1K DDRV_3 ARDQS0 ARDQ[0]
ARDQ[19] DQL2 VSS_9 J7
VDDQ_1
A8
J7
VDDQ_1
A1
A8
J7
VDDQ_1
A8 J7
VDDQ_1
A8 J7
VDDQ_1
A8
J7
K7
CK VDDQ_2
A8
C1 1% R4 B17
VSS_9 DQL2 ARDQ[3] F8 P9 K7
CK
CK
VDDQ_2
VDDQ_3
C1
K7
CK
CK
VDDQ_2
VDDQ_3
C1
K7
CK
CK
VDDQ_2
VDDQ_3
C1 K7
CK
CK
VDDQ_2
VDDQ_3
C1 K7
CK
CK
VDDQ_2
VDDQ_3
C1
K9
CK
CKE
VDDQ_3
VDDQ_4
C9
DDRV_4 ARDQ0 ARDQ[1]
P9 F8 DQL3 VSS_10
K9
CKE VDDQ_4
C9
D2
K9
CKE VDDQ_4
C9
K9
CKE VDDQ_4
C9
D2
K9
CKE VDDQ_4
C9
D2
K9
CKE VDDQ_4
C9
D2 VDDQ_5
D2
R5 D10
VSS_10 DQL3 ARDQ[20] H3 T1
L2
VDDQ_5
E9
L2
VDDQ_5
D2
E9
L2
VDDQ_5
E9 L2
VDDQ_5
E9 L2
VDDQ_5
E9
L2
K1
CS VDDQ_6
E9
F1

T1 H3 ARDQ[4] K1
CS
ODT
VDDQ_6
VDDQ_7
F1
K1
CS VDDQ_6
F1
K1
CS
ODT
VDDQ_6
VDDQ_7
F1 K1
CS
ODT
VDDQ_6
VDDQ_7
F1 K1
CS
ODT
VDDQ_6
VDDQ_7
F1
J3
ODT VDDQ_7
H2 DDRV_5 ARDQ1 ARDQ[2]
ARDQ[21] DQL4 VSS_11 J3
K3
RAS VDDQ_8
H2
H9
J3
ODT
RAS
VDDQ_7
VDDQ_8
H2
J3
K3
RAS VDDQ_8
H2
H9
J3
K3
RAS VDDQ_8
H2
H9
J3
K3
RAS VDDQ_8
H2
H9
K3
RAS
CAS
VDDQ_8
VDDQ_9
H9
K3 C17
VSS_11 DQL4 ARDQ[5] H8 T9 L3
CAS
WE
VDDQ_9 K3
L3
CAS VDDQ_9
H9
L3
CAS
WE
VDDQ_9
L3
CAS
WE
VDDQ_9
L3
CAS
WE
VDDQ_9 L3
WE
J1
R731 DDRV_6 ARDQ2 ARDQ[3]
T9 H8 DQL5 VSS_12 NC_1
J1 WE
NC_1
J1 NC_1
J1
NC_1
J1
NC_1
J1
T2
RESET
NC_1
NC_2
J9
1K C747 R6 C10
VSS_12 DQL5 ARDQ[22] G2
T2
RESET NC_2
J9
L1
T2
RESET NC_2
J9
T2
RESET NC_2
J9
L1
T2
RESET NC_2
J9
L1
T2
RESET NC_2
J9
L1 NC_3
L1

G2 ARDQ[6] NC_3
L9 NC_3
L1
L9
NC_3
L9
NC_3
L9
NC_3
L9
F3
NC_4
L9
T7 1% 0.1uF DDRV_7 ARDQ3 ARDQ[4]
ARDQ[23] DQL6 F3
DQSL
NC_4
F3
NC_4 F3
DQSL
NC_4
A14
T7 F3
DQSL
NC_4
A14
T7 F3
DQSL
NC_4
NC_6
T7
G3
DQSL NC_6
L8 C18
DQL6 ARDQ[7] ARDQ[24-31] H7
G3
DQSL G3
DQSL
DQSL
G3
DQSL
G3
DQSL
G3
DQSL
DQSL

DDRV_8 ARDQ4 ARDQ[5]

H7 DQL7 C7
B7
DQSU VSS_1
A9
B3
C7
DQSU VSS_1
A9
C7
B7
DQSU VSS_1
A9
B3
C7
B7
DQSU VSS_1
A9
B3
C7
B7
DQSU VSS_1
A9
B3
C7
B7
DQSU
DQSU
VSS_1
VSS_2
A9
B3
M8 B9
DQL7 B1 DQSU VSS_2
VSS_3
E1
B7
DQSU VSS_2
B3
E1
DQSU VSS_2
VSS_3
E1
DQSU VSS_2
VSS_3
E1
DQSU VSS_2
VSS_3
E1
E7
VSS_3
E1
G8
DDRV_9 ARDQ5 ARDQ[6]
B1 ARDQ[8-15] VSSQ_1
E7
DML VSS_4
G8
E7
DML
VSS_3
VSS_4
G8
E7
DML VSS_4
G8 E7
DML VSS_4
G8 E7
DML VSS_4
G8
D3
DML
DMU
VSS_4
VSS_5
J2
D17 E18
VSSQ_1 ARDQ[24] D7 B9
D3
DMU VSS_5
J2
J8
D3
DMU VSS_5
J2
D3
DMU VSS_5
J2
J8
D3
DMU VSS_5
J2
J8
D3
DMU VSS_5
J2
J8 VSS_6
J8

B9 D7 ARDQ[8] E3
VSS_6
M1
E3
VSS_6
J8
M1
E3
VSS_6
M1 E3
VSS_6
M1 E3
VSS_6
M1
E3
F7
DQ0 VSS_7
M1
M9
DDRV_10 ARDQ6 ARDQ[7]
ARDQ[25] DQU0 VSSQ_2 F7
DQL0
DQL1
VSS_7
VSS_8
M9
F7
DQL0 VSS_7
M9
F7
DQ0
DQ1
VSS_7
VSS_8
M9 F7
DQ0
DQ1
VSS_7
VSS_8
M9 F7
DQ0
DQ1
VSS_7
VSS_8
M9
F2
DQ1 VSS_8
P1 A19 D9
VSSQ_2 DQU0 ARDQ[9] C3 D1
F2
F8
DQL2 VSS_9
P1
P9
F2
DQL1
DQL2
VSS_8
VSS_9
P1
F2
F8
DQ2 VSS_9
P1
P9
F2
F8
DQ2 VSS_9
P1
P9
F2
F8
DQ2 VSS_9
P1
P9
F8
DQ2
DQ3
VSS_9
VSS_10
P9
DDRV_11 ARDQ7
D1 C3 DQU1 VSSQ_3 H3
DQL3
DQL4
VSS_10
VSS_11
T1
F8
H3
DQL3 VSS_10
P9
T1
H3
DQ3
DQ4
VSS_10
VSS_11
T1 H3
DQ3
DQ4
VSS_10
VSS_11
T1 H3
DQ3
DQ4
VSS_10
VSS_11
T1
H3
H8
DQ4 VSS_11
T1
T9

VSSQ_3 DQU1 ARDQ[26] C8 D8

H8
DQL5 VSS_12
T9
H8
DQL4 VSS_11
T9
H8
DQ5 VSS_12
T9 H8
DQ5 VSS_12
T9 H8
DQ5 VSS_12
T9
G2
DQ5 VSS_12

D8 C8 ARDQ[10] G2
H7
DQL6 G2
DQL5
DQL6
VSS_12 G2
H7
DQ6
G2
H7
DQ6
G2
H7
DQ6 H7
DQ6
DQ7

ARDQ[27] DQU2 VSSQ_4 DQL7

B1
H7
DQL7
B1
DQ7
B1
DQ7
B1
DQ7
B1
D7
VSSQ_1
B1
B9 J22 C15
VSSQ_4 DQU2 ARDQ[11] C2 E2 D7
DQU0
VSSQ_1
VSSQ_2
B9
D7
DQU0
VSSQ_1
VSSQ_2
B9
D7
DQ8
VSSQ_1
VSSQ_2
B9 D7
DQ8
VSSQ_1
VSSQ_2
B9 D7
DQ8
VSSQ_1
VSSQ_2
B9
C3
DQ8
DQ9
VSSQ_2
VSSQ_3
D1
TP700 MEMTP ARDQM1 ARDQM1
E2 C2 DQU3 VSSQ_5
C3
C8
DQU1 VSSQ_3
D1
D8
C3
DQU1 VSSQ_3
D1
C3
C8
DQ9 VSSQ_3
D1
D8
C3
C8
DQ9 VSSQ_3
D1
D8
C3
C8
DQ9 VSSQ_3
D1
D8
C8
DQ10 VSSQ_4
D8
K22 A13
VSSQ_5 DQU3 ARDQ[28] A7 E8
C2
DQU2 VSSQ_4
E2
C8
C2
DQU2 VSSQ_4
D8
E2
C2
DQ10 VSSQ_4
E2 C2
DQ10 VSSQ_4
E2 C2
DQ10 VSSQ_4
E2
C2
A7
DQ11 VSSQ_5
E2
E8
TP701 ARDQS1
E8 A7 ARDQ[12] A7
DQU3
DQU4
VSSQ_5
VSSQ_6
E8
A7
DQU3 VSSQ_5
E8
A7
DQ11
DQ12
VSSQ_5
VSSQ_6
E8 A7
DQ11
DQ12
VSSQ_5
VSSQ_6
E8 A7
DQ11
DQ12
VSSQ_5
VSSQ_6
E8
A2
DQ12 VSSQ_6
F9 MEMTN ARDQS1
ARDQ[29] DQU4 VSSQ_6 A2
B8
DQU5 VSSQ_7
F9
G1
A2
DQU4
DQU5
VSSQ_6
VSSQ_7
F9
A2
B8
DQ13 VSSQ_7
F9
G1
A2
B8
DQ13 VSSQ_7
F9
G1
A2
B8
DQ13 VSSQ_7
F9
G1
B8
DQ13
DQ14
VSSQ_7
VSSQ_8
G1 RVREF_A B13 ARDQ[8-15]
VSSQ_6 DQU4 ARDQ[13] A2 F9 A3
DQU6
DQU7
VSSQ_8
VSSQ_9
G9
B8
A3
DQU6 VSSQ_8
G1
G9
A3
DQ14
DQ15
VSSQ_8
VSSQ_9
G9 A3
DQ14
DQ15
VSSQ_8
VSSQ_9
G9 A3
DQ14
DQ15
VSSQ_8
VSSQ_9
G9
A3
DQ15 VSSQ_9
G9

ARDQS1 /ARDQS1
ARDQ[8]
F9 A2 DQU5 VSSQ_7
DQU7 VSSQ_9
B11
VSSQ_7 DQU5 ARDQ[30] B8 G1
G1 B8 ARDQ[14] ARDQ8 ARDQ[9]
ARDQ[31] DQU6 VSSQ_8 D18 B16
VSSQ_8 DQU6 ARDQ[15] A3 G9 RVREF_A ARDQ9 ARDQ[10]
G9 A3 DQU7 VSSQ_9 A11
VSSQ_9 DQU7 ARDQ10 ARDQ[11]
A17
ARDQ11 ARDQ[12]
G8 C12
ARCKE ARCKE ARDQ12 ARDQ[13]
A16
ARDQ13 ARDQ[14]
B5 C11
ARCLK1 ARCLK1 ARDQ14 ARDQ[15]
A5 C16
/ARCLK1 ARCLK1 ARDQ15

B14 A3
ARCLK0 ARCLK0 ARDQM2 ARDQM2
A14 D5
/ARCLK0 ARCLK0 ARDQS2 ARDQS2
C5
ARDQS2 /ARDQS2
ARDQ[16] ARDQ[16-23]
F13 E7
ARODT ARODT ARDQ16 ARDQ[17]
E13 B2
/ARRAS ARRAS ARDQ17 ARDQ[18]
G13 C8
/ARCAS ARCAS ARDQ18 ARDQ[19]
G15 B1
/ARCS ARCS ARDQ19 ARDQ[20]
H18 A9
/ARWE ARWE ARDQ20 ARDQ[21]
C1
ARDQ21 ARDQ[22]
G16 C9
ARREST ARRESET ARDQ22 ARDQ[23]
C3
+1.5V_DDR ARDQ23
D15
ARBA0 ARBA0
F9 C6
ARBA1 ARBA1 ARDQM3 ARDQM3
G18 A4
ARBA2 ARBA2 ARDQS3 ARDQS3
C703 C701 B4 ARDQ[24-31]
C718 C720 C722 C726 C728 ARDQS3 /ARDQS3
1uF 10uF F15 A1 ARDQ[24]
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
10V /ARCSX ARCSX ARDQ24 ARDQ[25]
B7
ARA[14] ARDQ25 ARDQ[26]
D11 C4
ARA[13] ARA14 ARDQ26 ARDQ[27]
F16 C7
ARA[12] ARA13 ARDQ27 ARDQ[28]
D8 B3
ARA[11] ARA12 ARDQ28 ARDQ[29]
E11 A7
ARA[10] ARA11 ARDQ29 ARDQ[30]
G9 A2
ARA[9] ARA10 ARDQ30 ARDQ[31]
E16 D7
+1.5V_DDR ARA[8] ARA9 ARDQ31
F11
ARA8 VDD3V3
ARA[7] G17
ARA[6] ARA
F10 A20
ARA[5] ARA6 AVDD33_MEMPLL
C717 C719 C750 C723 C725 C727 C706 C708 E17 H9
1uF 10uF ARA[4] ARA5 AVSS33_MEMPLL
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF E10
10V ARA[3] ARA4
E15 C700
ARA[2] ARA3 0.1uF
F17
ARA[1] ARA2
G10
ARA[0] ARA1
F18
ARA0
ARA[0-14]

IC702
MT41K128M16JT-125:K
+1.5V_DDR B_RVREF6 IC702-*1 IC702-*2 IC702-*3
IC105
DDR_256MB_MICRON BRA[0-14] K4B2G1646E-BCK0 H5TQ2G63DFR-PBC H5TQ2G63FFR-PBC LGE2122[A2_M13]
M8 N3 BRA[0] DDR_256MB_SS DDR_256MB_HYNIX_NC4.0 DDR_256MB_HYNIX_NC4.5 +1.5V_DDR RVREF_C
B_RVREF5 C709 VREFCA A0 BRA[1] N3 M8 N3 M8 N3
A0 VREFCA
M8
P7 P7
A0 VREFCA
P7
A0 VREFCA P7
R702 0.1uF A1 P3
A1 A1 P3
A1

1K B_RVREF5 P3 BRA[2] N2
A2
H1
P3
A2 N2
A2
H1
N2 H1
1% A2 A3 VREFDQ A3 VREFDQ P8
A3 VREFDQ
RVREF_C C2 L1
H1 N2 BRA[3] P8
A4
P8
A4 P2
A4 C741 RVREF_C BRDQM0 BRDQM0
P2
A5
P2
A5 A5 R726 0.1uF H2
VREFDQ A3 BRA[4] R8 L8 R8 L8 R8
A6 ZQ
L8
1K BRDQS0
P8 R2
A6 ZQ
R2
A6 ZQ R2
1% BRDQS0
A4 A7 A7 T8
A7 H1
R703 P2 BRA[5] T8
A8
T8
A8 A8
BRDQS0 /BRDQS0 BRDQ[0-7]
1K C710 1% R3
A9 VDD_1
B2 R3
A9 VDD_1
B2 R3
A9 VDD_1
B2
J2 E2 BRDQ[0]
1% R711 240 A5 BRA[6] L7 D9 L7 D9 L7
A10/AP VDD_2
D9
BRCLK0
0.1uF L8 R8 R7
A10/AP VDD_2
G7 R7
A10/AP VDD_2
G7 R7 G7 BRCLK0 BRDQ0 BRDQ[1]
ZQ A6 A11 VDD_3 A11 VDD_3 N7
A11 VDD_3
K2 J1 N3
R2 BRA[7] N7
A12/BC VDD_4
K2 N7
A12/BC VDD_4
K2 A12/BC VDD_4 R727 /BRCLK0 BRCLK0 BRDQ1
+1.5V_DDR T3
A13 VDD_5
K8 T3
A13 VDD_5
K8 T3
A13 VDD_5
K8
1K C742 E1 BRDQ[2]
A7 BRA[8] N1 N1 VDD_6
N1
1%
T8 M7
VDD_6
N9 M7
VDD_6
N9 M7 N9 0.1uF BRDQ2 BRDQ[3]
A8 NC_5 VDD_7
R1 NC_5 VDD_7 NC_5 VDD_7
R1 N1
B2 R3 BRA[9] VDD_8 VDD_8
R1 VDD_8
BRDQ3
M2
BA0 VDD_9
R9 M2
BA0 VDD_9
R9 M2
BA0 VDD_9
R9
D1 BRDQ[4]
+1.5V_DDR VDD_1 A9 BRA[10] N8 N8 N8
BA1
D9 L7 M3
BA1
M3
BA1 M3 BRDQ4 BRDQ[5]
VDD_2 A10/AP BA2
A1 BA2 BA2
A1 P1
G7 R7 BRA[11] VDDQ_1 VDDQ_1
A1 VDDQ_1
BRDQ5
J7
CK VDDQ_2
A8 J7
CK VDDQ_2
A8 J7
CK VDDQ_2
A8
L6 D2 BRDQ[6]
VDD_3 A11 BRA[12] K7 C1 K7 C1 K7
CK VDDQ_3
C1
BRCKE
B_RVREF6 K2 N7 K9
CK VDDQ_3
C9 K9
CK VDDQ_3
C9 K9 C9 BRCKE BRDQ6 BRDQ[7]
C711 VDD_4 A12/BC CKE VDDQ_4
D2 CKE VDDQ_4 CKE VDDQ_4
D2 N2
R704 K8 T3 BRA[13] VDDQ_5 VDDQ_5
D2
L2
VDDQ_5
E9 BRDQ7
1K 0.1uF L2
CS VDDQ_6
E9 L2
CS VDDQ_6
E9 CS VDDQ_6 E3
VDD_5 A13 K1 F1 K1 F1 K1
ODT VDDQ_7
F1
BRODT
1% N1 J3
ODT VDDQ_7
H2 J3
ODT VDDQ_7
H2 J3 H2 BRODT
VDD_6 K3
RAS VDDQ_8
H9 K3
RAS VDDQ_8
H9 K3
RAS VDDQ_8
H9 L4 H3
N9 M7 L3
CAS VDDQ_9
L3
CAS VDDQ_9 L3
CAS VDDQ_9 /BRRAS BRRAS BRDQM1 BRDQM1
VDD_7 NC_5 BRA[15] WE
J1 WE
J1
WE
J1 D3 K1
R1 T2
NC_1
J9 T2
NC_1
J9 T2
NC_1
J9 /BRCAS BRCAS BRDQS1 BRDQS1
R705 VDD_8 RESET NC_2
L1 RESET NC_2
L1
RESET NC_2
L1 D4 K2 BRDQ[8-15]
1K C712 R9 M2 NC_3
L9 NC_3
L9
NC_3
L9 /BRCS BRCS BRDQS1 /BRDQS1
BRDQ[8]
1% VDD_9 BA0 BRBA0 NC_4 NC_4 F3
NC_4
T7 N4
0.1uF N8
F3
DQSL NC_6
T7 F3
DQSL NC_6
T7 DQSL NC_6
BRDQ8
G3 G3 G3
DQSL J4 F2 BRDQ[9]
BA1 BRBA1 DQSL DQSL
M3 C7 A9 C7 A9 C7 A9 BRBA0 BRBA0 BRDQ9 BRDQ[10]
BA2 BRBA2 BRCLK0 B7
DQSU VSS_1
B3 B7
DQSU VSS_1
B3 B7
DQSU VSS_1
B3 M6 M3
A1 DQSU VSS_2
E1 DQSU VSS_2
E1
DQSU VSS_2
E1 BRBA1 BRBA1 BRDQ10 BRDQ[11]
VDDQ_1 E7
VSS_3
G8 E7
VSS_3
G8 E7
VSS_3
G8 E4 F1
A8 J7 D3
DML VSS_4
J2 D3
DML VSS_4
J2 D3
DML VSS_4
J2 BRBA2 BRBA2 BRDQ11 BRDQ[12]
VDDQ_2 CK R713 DMU VSS_5
J8 DMU VSS_5
J8
DMU VSS_5
J8 L2
C1 K7 100 E3
VSS_6
M1 E3
VSS_6
M1 E3
VSS_6
M1 BRDQ12 BRDQ[13]
VDDQ_3 CK 5% F7
DQL0 VSS_7
M9 F7
DQL0 VSS_7
M9 F7
DQL0 VSS_7
M9 BRA[0-15] K4 F3
C9 K9 F2
DQL1 VSS_8
P1 F2
DQL1 VSS_8
P1 F2
DQL1 VSS_8
P1 /BRWE BRWE BRDQ13 BRDQ[14]
VDDQ_4 CKE BRCKE F8
DQL2 VSS_9
P9 F8
DQL2 VSS_9
P9 F8
DQL2 VSS_9
P9 M4
DQL3 VSS_10
D2 H3
DQL3 VSS_10
T1 H3
DQL3 VSS_10
T1 H3 T1
BRA[15] BRDQ14 BRDQ[15]
VDDQ_5 /BRCLK0 H8
DQL4 VSS_11
T9 H8
DQL4 VSS_11
T9 H8
DQL4 VSS_11
T9 J3 G3
DQL5 VSS_12
E9 L2 G2
DQL5 VSS_12
G2
DQL5 VSS_12 G2
BRA[14] BRA15 BRDQ15
VDDQ_6 CS /BRCS H7
DQL6
H7
DQL6 H7
DQL6 P4
DQL7
F1 K1 DQL7
B1 DQL7
B1 B1
BRA[13] BRA14
VDDQ_7 ODT BRODT D7
VSSQ_1
B9 D7
VSSQ_1
B9 D7
VSSQ_1
B9 G5
DQU0 VSSQ_2
H2 J3 C3
DQU0 VSSQ_2
D1 C3
DQU0 VSSQ_2
D1 C3 D1
BRA[12] BRA13
VDDQ_8 RAS /BRRAS C8
DQU1 VSSQ_3
D8 C8
DQU1 VSSQ_3
D8 C8
DQU1 VSSQ_3
D8 P6
DQU2 VSSQ_4
H9 K3 C2
DQU2 VSSQ_4
E2 C2
DQU2 VSSQ_4
E2 C2 E2
BRA[11] BRA12
VDDQ_9 CAS /BRCAS A7
DQU3 VSSQ_5
E8 A7
DQU3 VSSQ_5
E8 A7
DQU3 VSSQ_5
E8 P5
DQU4 VSSQ_6
L3 A2
DQU4 VSSQ_6
F9 A2
DQU4 VSSQ_6
F9 A2 F9
BRA[10] BRA11
WE /BRWE B8
DQU5 VSSQ_7
G1 B8
DQU5 VSSQ_7
G1 B8
DQU5 VSSQ_7
G1 L5
DQU6 VSSQ_8
J1 A3
DQU6 VSSQ_8
G9 A3
DQU6 VSSQ_8
G9 A3 G9
BRA[9] BRA10
NC_1 DQU7 VSSQ_9 DQU7 VSSQ_9 DQU7 VSSQ_9 F4
J9 T2 BRA[8] BRA9
NC_2 RESET BRREST P3
L1 BRA[7] BRA8
NC_3 H4
L9 BRA[6] BRA7
NC_4 P2
T7 F3 BRA[5] BRA6
BRA[14] NC_6 DQSL BRDQS0 K6
G3 BRA[4] BRA5
DQSL /BRDQS0 M5
BRA[3] BRA4
K5
A9 C7 BRA[2] BRA3
VSS_1 DQSU BRDQS1 G6
B3 B7 BRA[1] BRA2
VSS_2 DQSU /BRDQS1 N5
E1 BRA[0] BRA1
VSS_3 E5
G8 E7 BRA0
VSS_4 DML BRDQM0 +1.5V_DDR
J2 D3
VSS_5 DMU BRDQM1
J8
VSS_6 BRDQ[0-7] B19
M1 E3 BRDQ[0] DDRV_12
VSS_7 DQ0 C19
M9 F7 BRDQ[1] DDRV_13
VSS_8 DQ1 D19
P1 F2 BRDQ[2] DDRV_14
VSS_9 DQ2 E19
P9 F8 BRDQ[3] DDRV_15
VSS_10 DQ3 F19
T1 H3 BRDQ[4] DDRV_16
VSS_11 DQ4 G19
T9 H8 BRDQ[5] DDRV_17
VSS_12 DQ5 F5
G2 BRDQ[6] DDRV_18
DQ6 H5
H7 BRDQ[7] DDRV_19
DQ7 N8 G4
B1 DDRV_20 BRRESET BRREST
BRDQ[8-15] P8
VSSQ_1
B9 D7 BRDQ[8] DDRV_21
VSSQ_2 DQ8 D13
D1 C3 BRDQ[9] DDRV_22
VSSQ_3 DQ9 E8
D8 C8 BRDQ[10] DDRV_23
VSSQ_4 DQ10 G11
E2 C2 BRDQ[11] DDRV_24
VSSQ_5 DQ11 D20
E8 A7 BRDQ[12] DDRV_25
VSSQ_6 DQ12 E20
F9 A2 BRDQ[13] DDRV_26
VSSQ_7 DQ13 F20
G1 B8 BRDQ[14] DDRV_27
VSSQ_8 DQ14 G20
G9 A3 BRDQ[15] DDRV_28
VSSQ_9 DQ15 R7
DDRV_29
R8
DDRV_30
T5
DDRV_31
T6
DDRV_32
T7
DDRV_33
T8
DDRV_34

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS 2011.12.09
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. DDR ONE SIDE 12

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 CI_A_DATA[0-7] CI_DATA[0-7]

CI_A_DATA[0] AR904 0 CI CI_DATA[0]

CI_A_DATA[1] CI_DATA[1]
CI DETECT CI_A_DATA[2] CI_DATA[2]
CI_A_DATA[3] CI_DATA[3]
CI_A_DATA[4] AR905 0 CI CI_DATA[4]
+3.3V_NORMAL CI_A_DATA[5] CI_DATA[5]
CI TS INPUT CI_A_DATA[6] CI_DATA[6]
CI_A_DATA[7] CI_DATA[7]
Close to MT5369 +5V_CI_ON
R910 R914
MT5398_TS_OUT[0-7] AR902 CI_MDI[0-7] 10K 10K
47 CI CI
MT5398_TS_OUT[0] CI CI_MDI[0]
MT5398_TS_OUT[1] CI_MDI[1] R929 R930
10K R933 R934 R935 R936
MT5398_TS_OUT[2] CI_MDI[2] /CI_CD1 47K 10K
10K 10K 10K
CI CI OPT
MT5398_TS_OUT[3] CI_MDI[3] OPT CI
/CI_CD2 CI

CI /PCM_WAIT
MT5398_TS_OUT[4] CI_MDI[4]
MT5398_TS_OUT[5] CI_MDI[5] +3.3V_NORMAL PCM_INPACK CI_A_ADDR[0-14] CI_ADDR[0-14]
MT5398_TS_OUT[6] CI_MDI[6]
MT5398_TS_OUT[7] CI_MDI[7] CI_VS1
CI_A_ADDR[0] AR906 0 CI CI_ADDR[0]
AR903 R906 R913 R918 R919 R923 R924 /PCM_REG CI_A_ADDR[1] CI_ADDR[1]
47 10K 47K 47K 47K 10K 10K CI_A_ADDR[2] CI_ADDR[2]
OPT CI CI CI OPT OPT /PCM_CE2 CI_A_ADDR[3] CI_ADDR[3]
PCM_RST
R907 47 CI CI_A_ADDR[4] AR907 0 CI CI_ADDR[4]
MT5398_MISTRT CI_IN_TS_SYNC R900 /PCM_IRQA
R908 10K CI_A_ADDR[5] CI_ADDR[5]
47 CI CI_IN_TS_VAL
MT5398_MIVAL_ERR OPT CI_A_ADDR[6] CI_ADDR[6]
MT5398_MCLKI R909 47 CI
CI_IN_TS_CLK CI_A_ADDR[7] CI_ADDR[7]
CI_A_ADDR[8] AR908 0 CI CI_ADDR[8]
C902
Close to MT5369 CI_A_ADDR[9] CI_ADDR[9]
12pF 22 R931
50V CI_VS1 CI_A_ADDR[10] CI_ADDR[10]
OPT
Close to CI Slot CI_A_VS1
OPT CI_A_ADDR[11] CI_ADDR[11]
CI_A_ADDR[12]AR909 0 CI CI_ADDR[12]
R932 22
CI_A_ADDR[13] CI_ADDR[13]
/PCM_A_REG /PCM_REG
OPT CI_A_ADDR[14] CI_ADDR[14]
CI TS OUTPUT
/PCM_IORD
/PCM_IOWR
MT5398_TS_IN[0-7] Close to CI Slot CI_TS_DATA[0-7]
/PCM_OE
MT5398_TS_IN[0] AR900 47 CI CI_TS_DATA[0]
MT5398_TS_IN[1] /PCM_WE
CI_TS_DATA[1]
MT5398_TS_IN[2]
CI_TS_DATA[2] /PCM_CE1
MT5398_TS_IN[3]
CI_TS_DATA[3]

MT5398_TS_IN[4] AR901 47 CI CI_TS_DATA[4]

MT5398_TS_IN[5] CI_TS_DATA[5]
MT5398_TS_IN[6] CI_TS_DATA[6]
MT5398_TS_IN[7]
CI_TS_DATA[7]

Close to CI Slot
+5V_CI_ON
R915 47 CI
MT5398_TS_CLK CI_TS_CLK
R916 47 CI
MT5398_TS_VAL CI_TS_VAL
R917 47 CI
MT5398_TS_SYNC CI_TS_SYNC
C900
C904 C905 CI_A_DATA[0-7]
12pF 0.1uF 10uF
50V CI 10V
OPT JK900
CI
10120698-015LF

35 1
100 CI_NC4.0
Close to MT5398 /CI_CD1 R927 36 2 CI_A_DATA[3]
/PCM_CE1
CI 37 3 CI_A_DATA[4]
CI_TS_DATA[3]
38 4 CI_A_DATA[5]
CI_TS_DATA[4]
39 5 CI_A_DATA[6]
CI_TS_DATA[5]
40 6 CI_A_DATA[7]
CI_TS_DATA[6]
CI_TS_DATA[7] 41 7 CI R939 22
R911 CI 22
/PCM_CE2 42 8 CI_A_ADDR[10]
/PCM_IORD
/PCM_IOWR CI_VS1 43 9
R912 22 44 10 CI_A_ADDR[11]
CI CI_MDI[0-7] 45 11 CI_A_ADDR[9]
46 12 CI_A_ADDR[8]
CI_MDI[0] 47 13
JK900-*1 CI_A_ADDR[13] CI R941 22
10125901-015LF CI_MDI[1] 48 14 CI_A_ADDR[14] /PCM_OE
CI_MDI[2] CI R942 22
49 15
1 35 /PCM_WE
CI_MDI[3] 50 16 R940 22 CI
CI_NC4.5 /PCM_IRQA
2 36 C906 0.1uF C907
51 17 CI
3 37 R926 OPT R938 CI 0.1uF
0 52 18 0 OPT 16V
4 38 CI_MDI[4] 53 19
5 39 CI_MDI[5] 54 20
6 40 CI_MDI[6] 55 21 CI_A_ADDR[12]
7 41 CI_MDI[7] 56 22 CI_A_ADDR[7]
8 42
CI_TS_CLK 57 23 CI_A_ADDR[6]
9 43 R921 22 CI
PCM_RST 58 24 CI_A_ADDR[5]
10 44 R922 22 CI
/PCM_WAIT 59 25 CI_A_ADDR[4]
11 45 R920 22 OPT
PCM_INPACK 60 26 CI_A_ADDR[3]
12 46
61 27 CI_A_ADDR[2]
13 47 /PCM_A_REG
CI_TS_VAL 62 28 CI_A_ADDR[1]
14 48
CI_TS_SYNC 63 29 CI_A_ADDR[0]
15 49 CI_A_DATA[0]
CI_TS_DATA[0] 64 30
16 50 CI_A_DATA[1] +5V_CI_ON
CI_TS_DATA[1] 65 31
17 51 CI_A_DATA[2]
CI_TS_DATA[2] 66 32
18 52
/CI_CD2 R928 CI 100 67 33 R937 10K
19 53 OPT
68 34
20 54
R925 0
21 55 G2 69 G1
22 56 CI

23 57
24 58
25 59
CI_IN_TS_VAL
26 60
CI_IN_TS_CLK
27 61
CI_IN_TS_SYNC
28 62
29 63
30 64
31 65
32 66
33 67
34 68

G1 69 G2

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MID_MAIN_CI 2011.11.21
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 13

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 SPDIF

+3.3V_NORMAL

GND
SPDIF OUT
1

Fiber Optic

JST1223-001
JK3602
R3611 VCC
2.7K 2
R3610 OPT
33 VINPUT
3

SPDIF_OUT
C3602
4

0.1uF
FIX_POLE

16V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS JACK HIGH / MID 2011.11.21
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 36

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 JK3700
PEJ034-01

E_SPRING 3

R_SPRING 4
HP_ROUT
T_SPRING 5
HP_LOUT
B_TERMINAL2 7B

T_TERMINAL2 6B
+3.3V_NORMAL

R3700
10K
R3701
1K
HP_DET

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS JACK_COMMON 2011.11.21
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 37

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 +3.3V_NORMAL

EU
R4601
10K CLOSE TO JUNCTION

R4602
1K
SC_DET
EU
VA4601 C4604
5.6V 0.1uF
OPT

Full Scart(18 Pin Gender)

SC_CVBS_IN

VA4609
5.5V
EU
EU
EU
AV_DET 1/16W
22
COM_GND 0
VA4610 R8904 DTV/MNT_V_OUT
21 5.5V
SYNC_IN EU
20
SYNC_OUT
19
SYNC_GND2
18
SYNC_GND1
17
RGB_IO
16 SC_FB
R_OUT VA4602
15 5.6V
RGB_GND EU
14
R_GND
13 SC_R
D2B_OUT
12 VA4603
G_OUT
5.5V
11 OPT
D2B_IN
10
G_GND
9 SC_G
ID
8 VA4604
B_OUT
5.5V
7
AUDIO_L_IN OPT
6
B_GND
5
AUDIO_GND SC_B
4
AUDIO_L_OUT VA4605
3 5.5V
AUDIO_R_IN OPT
2
AUDIO_R_OUT
1 SC_ID
VA4600
20V

PSC008-01 EU
JK4600
SC_L_IN

VA4611
5.6V
OPT

SC_R_IN

VA4606
5.6V
OPT

BLM18PG121SN1D
L4600
DTV/MNT_L_OUT
VA4607 EU EU EU
5.6V C4600 C4602
OPT 1000pF 4700pF
50V

BLM18PG121SN1D
L4601
DTV/MNT_R_OUT
EU
VA4608 EU EU C4603
5.6V C4601 4700pF
OPT 1000pF
50V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS SCART GENDER 2011.10.26
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 46

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 L5404-*1
10.0uH
Audio_Coil_TAIYO
NRS6045T100MMGK

L5405-*1
10.0uH Audio_Coil_TAIYO
NRS6045T100MMGK

DUAL COMPONENT +3.3V_NORMAL AMP_RESET_N

L5402-*1
10.0uH Audio_Coil_TAIYO
C5415
1000pF
Q1801 50V NRS6045T100MMGK
1ST : 0TRIY80001A 2ND : 0TR387500AA

50V
L5401

22000pF
L5403-*1

C5416
BLM18PG121SN1D +24V_AMP
OPT 10.0uH Audio_Coil_TAIYO
AUD_MASTER_CLK R5406
3.3 NRS6045T100MMGK

+24V_AMP OPT
+24V
C5418 C5420 C5422 C5424
0.1uF 0.1uF 10uF 0.01uF
C5413 C5414 50V
50V 50V 35V
L5400
0.1uF
10uF
[EP]GND
VDD_IO
GND_IO

PGND1A

PVDD1A
PVDD1B
10V
UBW2012-121F 16V SPK_L+

CLK_I

RESET
BST1A

OUT1A
R5407 R5414
12 12 L5404
10uH C5436 R5415
Audio_Coil_ABCO 0.1uF

AD
C5400 C5401 C5411 C5429 50V 5.1K
0.1uF 0.1uF 0.1uF 390pF LPH6045T-100M
50V 50V 16V 50V C5434
L5405 0.47uF
C5430
10uH Audio_Coil_ABCO
50V
SPEAKER_L
390pF C5437
40
39
38
37
36
35
34
33
32
31
50V LPH6045T-100M 0.1uF R5416
50V
R5408 R5412 5.1K
AGND_PLL 1 30 OUT1B 12 12
SPK_L-
VDD_PLL 2 29 PGND1B C5425
THERMAL 22000pF
DGND_PLL 3 41 28 BST1B 50V WAFER-ANGLE

GND 4 27 VDR1
SPK_L+
4
OPT C5440 DGND 5 IC5400 26 VCC5
0.1uF C5412
1uF
16V 10V DVDD 6 NTP7513 25 AGND SPK_L-
3

AUD_LRCH
SDATA 7 24 VDR2 SPK_R+
2

WCK
0x54 BST2A
C5427
1uF
C5428
1uF
C5433
1uF
AUD_LRCK 8 23 10V 10V 10V SPK_R-
1

AUD_SCK
BCK 9 22 PGND2A C5426
22000pF P5400

I2C_SDA1
R5402 100 SDA 10 21 OUT2A 50V
11
12
13
14
15
16
17
18
19
20

R5403 100
I2C_SCL1
C5406 C5408
SCL
FAULT
MONITOR_0
MONITOR_1
MONITOR_2
BST2B
PGND2B
OUT2B
PVDD2B
PVDD2A

POWER_DET
33pF 33pF
SPK_R+
AMP_MUTE_PWR_DET

50V 50V

+3.3V_NORMAL
+24V_AMP
R5409 R5413
R5419 100

12 12 L5402
10uH Audio_Coil_ABCO C5438 R5417
AMP_MUTE_MICOM LPH6045T-100M 0.1uF 5.1K
R5401 C5431
10K 390pF C5435 50V
50V 0.47uF
R5405 100 C5419 C5421 C5423
L5403
10uH Audio_Coil_ABCO
50V
SPEAKER_R
AMP_MUTE_MICOM 0.1uF 0.1uF 10uF C5432
C C5404 390pF
50V 50V 50V LPH6045T-100M C5439 R5418
1000pF 35V
R5400 10K B C5417
AMP_MUTE Q5400 50V R5410 R5411 0.1uF 5.1K
AMP_MUTE_MICOM MMBT3904(NXP) 22000pF 12 12 50V
E AMP_MUTE_MICOM 50V
SPK_R-

[AMP_MUTE_PWR_DET]
-->For fixing AC-OFF POP noise 32"POLA/ROW model
-->32"POLA/ROW LPB’s 3.5st drop time is very fast

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS AMP_NEO 2011.11.21
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 54

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 +12V

EU
AUD_OUT >> EU/CHINA_HOTEL_OPT
IC6000 L6000
AZ4580MTR-E1
EU
EU
2.2K R6000 OUT1 8 VCC C6004
DTV/MNT_L_OUT 1
EU
C6000 OPT
0.1uF
50V R6011
EU
C6008
[SCART AUDIO MUTE]
OPT R6002 EU IN1- OUT2 SIGN600002 2.2K
1uF 33K R6004 2 7
25V C6002 470K DTV/MNT_R_OUT
EU 6800pF
33pF C6003
IN1+ EU 6 IN2- R6008
EU
33K
OPT
R6010
OPT 1uF DTV/MNT_L_OUT

EU 3 C6007 25V
470K
6800pF
EU
VEE 5 IN2+ C
4 C6005 EU R6013
33pF Q6000 B 1K
SCART_AMP_L_FB MMBT3904(NXP)
EU_SCART_MUTE_ISAHAYA
SCART_AMP_R_FB E EU Q6002
RT1P141C-T112
SCART_MUTE

E
B
SCART_Lout
SCART_Rout
DTV/MNT_R_OUT
PDTA114ET
Q6002-*1
EU

E
C
R6014
Q6001 B 1K
MMBT3904(NXP)

B
E EU EU_SCART_MUTE_NXP

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS SCART AUDIO AMP 2011.11.21
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 60

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 HP_OUT_H13 HP_OUT_H13

C6104-*1 C6109-*1

EARPHONE AMP 18pF

18pF

IC6100
TPA6138A2

HP_OUT_MTK +INR +INL HP_OUT_MTK

C6104 1 14 C6109
HP_OUT
C6100 180pF HP_OUT HP_OUT HP_OUT 180pF HP_OUT C6101
1uF R6100 R6106 R6104 R6101 1uF
-INR -INL HP_OUT
HP_OUT 10K
10V 43K HP_OUT 2 13
43K 10K 10V
HP_OUT
HP_ROUT_MAIN HP_LOUT_MAIN
R6103 1% C6108 C6106 1% R6102
33K 10pF OUTR OUTL 10pF 33K
HP_OUT_MTK 50V 3 12 50V HP_OUT_MTK HP_OUT_H13
HP_OUT_H13 HP_LOUT_AMP R6102-*1
R6103-*1 HP_ROUT_AMP 43K
+3.3V_NORMAL GND_1 UVP
43K 4 11 +3.3V_NORMAL
1%
1%

HP_OUT
MUTE GND_2
4.7K
HP_OUT

5 10 L6100
R6105
120-ohm
SIDE_HP_MUTE VSS VDD BLM18PG121SN1D
6 9
HP_OUT HP_OUT
HP_OUT
C6105 C6107
C6102 CN CP 1uF 0.1uF
1uF 7 8
10V 16V
10V

C6103
1uF
10V

HP_OUT

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. 2011.09.29
HEADPHONE AMP
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR 61
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 CI POWER ENABLE CONTROL
IC6200
+5V_NORMAL
AP2151WG-7 +5V_CI_ON

IN OUT
5 1
CI
GND C6210
2 1uF
CI R6219
25V
CI 10K
R6217
100 EN FLG CI
PCM_5V_CTL 4 3

R6218
10K
CI

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS CI SLOT 2011.10.31
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 62

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 B-CAS (SMART CARD) INTERFACE

+3.3V_NORMAL INT CMDVCC : STATUS

+3.3V_NORMAL ---------------------------------
HIGH HIGH CARD PRESENT
LOW HIGH CARD not PRESENT
SIGN630028
IC6300
TDA8024TT
2.7K

2.7K
R6301

R6303

R6305
JAPAN

JAPAN
CLKDIV1 CLKDIV2 : F_CRD_CLK

OPT
-----------------------------
1 0 CLKIN CLKDIV1 AUX2UC
1 28

JAPAN

JAPAN

JAPAN
R6317

R6318

R6315

R6319

R6316
OPT

OPT
1.2K

1.2K

1.2K

1.2K

1.2K
CLKDIV2 AUX1UC
2 27
JAPAN

5V/3V I/OUC JAPAN

SMARTCARD_PWR_SEL/SD_EMMC_DATA[1] R6300 22 3 26 R6307 22 SMARTCARD_DATA/SD_EMMC_CLK
2.7K
R6302

R6304

R6306
JAPAN
OPT

OPT

PGND XTAL2 JAPAN

+5V_NORMAL 4 25 R6308 22 SMARTCARD_CLK/SD_EMMC_DATA[0]

S2 XTAL1 JAPAN
JAPAN 5 24 R6309 22 SMARTCARD_DET/SD_EMMC_DATA[3]
L6300
BLM18PG121SN1D VDDP OFF JAPAN
JAPAN 6 23 R6310 22 SMARTCARD_RST/SD_EMMC_DATA[2]
JAPAN
JAPAN C6301 C6303
C6300 0.1uF S1 GND JAPAN
10uF
0.1uF 10V 16V 7 22 R6311 22 SMARTCARD_VCC/SD_EMMC_CMD
16V L6301 JAPAN

+3.3V_NORMAL
JAPAN
VUP VDD BLM18PG121SN1D
8 21
JAPAN
JAPAN JAPAN
C6302 PRES RSTIN C6305 C6306
0.1uF 9 20 0.1uF 0.1uF
16V 16V 16V
B-CAS SLOT
PRES CMDVCC
10 19
P6300
I/O PORADJ 10057542-1311FLF(B CAS Slot)
11 18

AUX2 VCC JAPAN VCC

12 17 C1
C6307
0.33uF
AUX1 RST 16V RST
13 16 C2

CGND CLK Place CLK C3 far from C2,C7,C4 and C8 CLK

14 15 C3

JAPAN
C6304 RESERVED_1
0.1uF C4
16V
GND
C5

VPP JAPAN
C6
JAPAN
R6313
75 I/O
C7
75 ohm in I/O is for short circuit Protection
RESERVED
C8

SW1
S1
+3.3V_NORMAL
JAPAN

JAPAN

10K
R6312
R6314
1K SW2
S2

ZD6300 ZD6301

JAPAN

JAPAN
5V 5V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS CI SLOT 2011.04.17
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 62

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 DEV_TU_DVB_T/C DEV_TU_DVB_T2/C/S2 DEV_TU_J_JP
TU6601 TU6602 TU6603
TDJH-G101D TDJM-G101D TDJW-J201F
1
B1[+3.3V] B1[+3.3V] B1[+3.3V]
1 1 1 +3.3V_LNA_TU 2
NC_1 NC_1 NC_1
2 2 2 RF_SWITCH_CTL_TU 3
IF_AGC AIF_AGC NC_2
3 3 3 IF_AGC_TU 4
SCL SCL_RF SCL_RF
4 4 4 I2C_SCL6_TU 5
SDA SDA_RF SDA_RF
5 5 5 I2C_SDA6_TU 6
IF[P] AIF[P] NC_3
6 6 6 IF_P 7
IF[N] AIF[N] NC_4
7 7 7 IF_N 8
NC_2 NC_2 NC_5
8 8 8 TU_SIF_TU 9
NC_3 NC_3 NC_6
9 9 9 TU_CVBS_TU 10
NC_4 NC_7
10 10 11
A1 B1 B2[+3.3V] B2[+3.3V]
A1 B1 11 11 +3.3V_TU 12
47 ERROR NC_8
12 12

TU_GND_B
FE_DEMOD1_TS_ERROR 13
GND_1 GND_1
SHIELD 13 13 14
MCLK
14 FE_DEMOD1_TS_CLK
SYNC
15 FE_DEMOD1_TS_SYNC 16
VALID
16 FE_DEMOD1_TS_VAL 17
D0
17 FE_DEMOD1_TS_DATA[0] 18
D1
TU_GND_B

18 FE_DEMOD1_TS_DATA[1] 19
D2
19 FE_DEMOD1_TS_DATA[2] 20
D3
20 FE_DEMOD1_TS_DATA[3] 21
D4
C6601 21 FE_DEMOD1_TS_DATA[4] 22
1000pF D5
630V 22 FE_DEMOD1_TS_DATA[5] 23
D6
23 FE_DEMOD1_TS_DATA[6] 24
D7
24 FE_DEMOD1_TS_DATA[7] 25
RESET_DEMOD M_RESET_DEMOD
25 25 /TU_RESET1_TU 26
B3[+3.3V] B3[+3.3V]
26 26 +3.3V_DEMOD_TU 27
DVB-T GND SCL_DEMOD SCL_DEMOD
27 27 I2C_SCL4_TU
B4[+1.1V] B4[+1.2V]
28 28 D_Demod_Core
F22_OUTPUT NC_9
29 29 LNB_TX 30
SDA_DEMOD SDA_DEMOD
30 30 I2C_SDA4_TU 31
LNB LNB
31 31 LNB_OUT 32
GND GND_2
32 32 33
NC_10
33 34
A1 B1 M_ERROR
A1 B1 34 FE_DEMOD2_TS_ERROR 35
47 GND_3
35 36

TU_GND_B
M_SYNC
47 36 FE_DEMOD2_TS_SYNC
M_MCLK
37 FE_DEMOD2_TS_CLK
B5[+2.5V]
38 +2.5V_DEMOD
M_VALID
39 FE_DEMOD2_TS_VAL 40
M_DATA
40 FE_DEMOD2_TS_DATA 41
S_ERROR
41 FE_DEMOD3_TS_ERROR 42
S_SYNC
42 FE_DEMOD3_TS_SYNC 43
S_MCLK
43 FE_DEMOD3_TS_CLK 44
TU6602-*1
TDJM-C301D
S_VALID
1
DEV_TU_China
B1[+3.3V] 44 FE_DEMOD3_TS_VAL 45
150mA(MAX) RF_SW_CTL
2
NC_1 S_RESET_DEMOD
3
SCL_RF 45 /TU_RESET2_TU 46
+3.3V_NORMAL +2.5V_NORMAL 4
SDA_RF
5
NC_2 S_DATA
IC6600
6

7
NC_3 46 FE_DEMOD3_TS_DATA 47
SIF
TJ1118S-2.5 8
CVBS
9

10
NC_4
48
IN 3 2 OUT NC_5
11
ERROR A1 B1
C6603 1
12

13
GND_1 A1 B1 49
0.1uF GND C6605 MCLK

16V TU_J_JP
C6604 0.1uF TU_J_JP 14
SYNC 47
TU_J_JP 22uF 16V 15
VAILD
16
10V D0

TU_GND_B
17
85C D1
TU_J_JP 18

19
D2 SHIELD
D3
20
+2.5V_NORMAL D4
21
TU_J_JP D5
L6602 22
D6
BLM18PG121SN1D 23
D7
24
+2.5V_DEMOD 25
RESET_DEMOD

B2[+3.3V]
26
C6608 SCL_DEMOD
27
0.1uF B3[+1.1V]
28

TU_J_JP 29
NC_6

SDA_DEMOD
30

A1 B1
A1 B1
47

SHIELD

FE_DEMOD3_TS_ERROR
FE_DEMOD2_TS_ERROR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 DVB-S2 LNB Part Allegro
(Option:LNB) Input trace widths should be sized to conduct at least 3A
Ouput trace widths should be sized to conduct at least 2A
3A

+12V

2A
D6904-*1
Max 1.3A
40V
LNB_SX34
D6902
D6902-*1 3.5A
LNB_Onsemi D6904
SS23L

30V 40V

LNB
15uH
SP-7850_15

L6900
30V
LNB_TSC LNB_SMAB34
C6909
10uF
C6903 C6905 C6906 C6907 25V
0.01uF 10uF 10uF 10uF LNB
50V 25V 25V 25V
LNB LNB LNB LNB

C6908 0.1uF
close to Boost pin(#1) A_GND
A_GND

D6901-*1

LNB

[EP]GND
close to VIN pin(#15) Caution!! need isolated GND
SS23L

BOOST

GNDLX
R6904

NC_3

NC_2
C6910 0
A_GND

LX
30V 0.1uF
LNB_TSC 50V

20

19

18

17

16
LNB
D6901 VCP 1 15 VIN
MBR230LSFT1G THERMAL A_GND
LNB 2 14 GND
LNB_OUT 21
30V LNB
D6903 NC_1 3 13 VREG
LNB_Onsemi C6904
0.1uF LNB_SMAB34 IC6900 R6903
C6900 C6901 R6900 TDI ISET 39K
2.2K LNB 50V 40V A8303SESTR-T
4 12
18pF 33pF
D6900 1W LNB 1/16W
LNB LNB C6902 TDO 5 11 TCAP C6912
LNB LNB 0.22uF 1%
LNB 25V D6903-*1

10
LNB
LNB_SX34
6

9 0.1uF
40V
IRQ

SCL

SDA

ADD

TONECTRL

0.22uF
Close to Tuner A_GND
A_GND
Surge protectioin

LNB
C6911
R6901 33

R6902 33
LNB
LNB
I2C_SCL4

I2C_SDA4

LNB_TX

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
LNB 2012.03.08
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
69
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 IC8100-*4
IC8100-*1 IC8100-*2 IC8100-*3
THGBM5G7A2JBAIR
THGBM5G5A1JBAIR H26M21001ECR KLM2G1HE3F-B001

A3 C8
A3 C8 A3 C8 A3 C8 DAT0 NC_23
DAT0 NC_23 DAT0 NC_25 DAT0 NC_25 A4 C9
A4 C9 A4 C9 A4 C9 DAT1 NC_24

eMMC I/F A5
B2
DAT1
DAT2
DAT3
NC_24
NC_25
NC_26
C10
C11
A5
B2
DAT1
DAT2
DAT3
NC_26
NC_27
NC_28
C10
C11
A5
B2
DAT1
DAT2
DAT3
NC_26
NC_27
NC_28
C10
C11
A5
B2
B3
DAT2
DAT3
NC_25
NC_26
C10
C11
C12
B3 C12 B3 C12 B3 C12 DAT4 NC_27
DAT4 NC_27 DAT4 NC_29 DAT4 NC_29 B4 C13
EMMC DATA LINE 47K PULL/UP 3.3V_EMMC B4 C13 B4 C13 B4 C13 DAT5 NC_28
DAT5 NC_28 DAT5 NC_30 DAT5 NC_30 B5 C14
B5 C14 B5 C14 B5 C14 DAT6 NC_29
47K
47K
47K
47K
47K

47K
47K
47K

DAT6 NC_29 DAT6 NC_31 DAT6 NC_31 B6 D1

B6 D1 B6 D1 B6 D1 DAT7 NC_30
DAT7 NC_30 DAT7 NC_32 DAT7 NC_32 D2
D2 D2 D2 NC_31
NC_31 NC_33 NC_33 D3
D3 D3 D3 NC_32
R8104-*1
R8100-*1
R8101-*1
R8102-*1
R8103-*1

R8105-*1
R8106-*1
R8107-*1

NC_32 NC_34 NC_34 M6 D4

R8117

R8116
10K
10K
10K
10K

10K
10K
10K
10K

EMMC DATA LINE M6 D4 M6 D4 M6 D4 CLK NC_33

CLK NC_33 CLK NC_35 CLK NC_35 M5 D12

10K

10K
10K PULL/UP M5 D12 M5 D12 M5 D12 CMD NC_34
FOR M13 CMD NC_34 CMD NC_36 CMD NC_36 D13
R8100
R8101
R8102
R8103

R8104
R8105
R8106
R8107

D13 D13 D13 NC_35

NC_35 NC_37 NC_37 D14
IC8100 D14 D14 D14 NC_36
NC_36 NC_38 NC_38 A6 E1
EMMC_SERIAL_22 H26M31002GPR A6 E1 A6 E1 A6 E1 RFU_1 NC_37
EMMC_DATA[0-7] RFU_1 NC_37 NC_3 NC_39 NC_3 NC_39 A7 E2
AR8100 A7 E2 A7 E2 A7 E2 RFU_2 NC_38
22 RFU_2 NC_38 NC_4 NC_40 NC_4 NC_40 C5 E3
1/16W C5 E3 C5 E3 C5 E3 NC_21 NC_39
NC_21 NC_39 NC_23 NC_41 NC_23 NC_41 E5 E12
EMMC_DATA[0] A3 C8 E5 E12 E5 E12 E5 E12 RFU_3 NC_40
DAT0 NC_25 RFU_3 NC_40 NC_42 NC_46 NC_42 NC_46 E8 E13
EMMC_DATA[1] A4 C9 E8 E13 E8 E13 E8 E13 RFU_4 NC_41
DAT1 NC_26 RFU_4 NC_41 NC_43 NC_47 NC_43 NC_47 E9 E14
EMMC_DATA[2] A5 C10 E9 E14 E9 E14 E9 E14 RFU_5 NC_42
DAT2 NC_27 RFU_5 NC_42 NC_44 NC_48 NC_44 NC_48 E10 F1
EMMC_DATA[3] B2 C11 E10 F1 E10 F1 E10 F1 RFU_6 NC_43
EMMC_DATA[4] DAT3 NC_28 RFU_6 NC_43 NC_45 NC_49 NC_45 NC_49 F10 F2
B3 C12 F10 F2 F10 F2 F10 F2 RFU_7 NC_44
EMMC_DATA[5] DAT4 NC_29 RFU_7 NC_44 NC_52 NC_50 NC_52 NC_50 G3 F3
B4 C13 G3 F3 G3 F3 G3 F3 RFU_8 NC_45
EMMC_DATA[6] DAT5 NC_30 RFU_8 NC_45 NC_58 NC_51 NC_58 NC_51 G10 F12
EMMC_SERIAL_22 B5 C14 G10 F12 G10 F12 G10 F12 RFU_9 NC_46
EMMC_DATA[7] AR8101 DAT6 NC_31 RFU_9 NC_46 NC_59 NC_53 NC_59 NC_53 H5 F13
22 B6 D1 H5 F13 H5 F13 H5 F13 RFU_10 NC_47
1/16W DAT7 NC_32 DAT5 RFU_10 NC_47 NC_66 NC_54 NC_66 NC_54 J5 F14
D2 J5 F14 J5 F14 J5 F14 RFU_11 NC_48
NC_33 RFU_11 NC_48 NC_73 NC_55 NC_73 NC_55 K6 G1
D3 K6 G1 K6 G1 K6 G1 RFU_12 NC_49
NC_34 RFU_12 NC_49 NC_80 NC_56 NC_80 NC_56 K7 G2
M6 D4 K7 G2 K7 G2 K7 G2 RFU_13 NC_50
CLK NC_35 RFU_13 NC_50 NC_81 NC_57 NC_81 NC_57 K10 G12
M5 D12 K10 G12 K10 G12 K10 G12 RFU_14 NC_51
CMD NC_36 RFU_14 NC_51 NC_82 NC_60 NC_82 NC_60 P7 G13
D13 P7 G13 P7 G13 P7 G13 RFU_15 NC_52
NC_37 RFU_15 NC_52 NC_116 NC_61 NC_116 NC_61 P10 G14
D14 P10 G14 P10 G14 P10 G14 RFU_16 NC_53
NC_38 RFU_16 NC_53 NC_119 NC_62 NC_119 NC_62 H1

HYNIX_EMMC_2GB
A6 E1 H1 H1 H1 NC_54

TOSHIBA_EMMC_4GB
NC_3 NC_39 NC_54 NC_63 NC_63 H2
A7 E2 H2 H2 H2 NC_55
NC_4 NC_40 NC_55 NC_64 NC_64 K5 H3

TOSHIBA_EMMC_16GB
C5 E3 K5 H3 K5 H3 K5 H3 RSTN NC_56
NC_23 NC_41 RST_N NC_56 RESET NC_65 RSTN NC_65 H12

SAMSUNG_EMMC_2GB
E5 E12 H12 H12 H12 NC_57
NC_42 NC_46 NC_57 NC_67 NC_67 H13
EMMC_SERIAL_22 E8 E13 H13 H13 H13 NC_58
NC_43 NC_47 NC_58 NC_68 NC_68 C6 H14
AR8102 22 E9 E14 C6 H14 C6 H14 C6 H14 VCCQ_1 NC_59
EMMC_CLK NC_44 NC_48 VCCQ_1 NC_59 VCCQ_1 NC_69 VDD_1 NC_69 M4 J1
E10 F1 M4 J1 M4 J1 M4 J1 VCCQ_2 NC_60
EMMC_CMD NC_45 NC_49 DAT6 VCCQ_2 NC_60 VCCQ_2 NC_70 VDD_2 NC_70 N4 J2
F10 F2 N4 J2 N4 J2 N4 J2 VCCQ_3 NC_61
EMMC_RST NC_52 NC_50 VCCQ_3 NC_61 VCCQ_3 NC_71 VDD_3 NC_71 P3 J3
G3 F3 P3 J3 P3 J3 P3 J3 VCCQ_4 NC_62
NC_58 NC_51 VCCQ_4 NC_62 VCCQ_4 NC_72 VDD_4 NC_72 P5 J12
G10 F12 P5 J12 P5 J12 P5 J12 VCCQ_5 NC_63
NC_59 NC_53 VCCQ_5 NC_63 VCCQ_5 NC_74 VDD_5 NC_74 J13
H5 F13 J13 J13 J13 NC_64
NC_66 NC_54 NC_64 NC_75 NC_75 J14
J5 F14 J14 J14 J14 NC_65
C8107 NC_73 NC_55 NC_65 NC_76 NC_76 E6 K1
eMMC serial 100 ohm option OPT 10pF K6 G1 E6 K1 E6 K1 E6 K1 VCC_1 NC_66
NC_80 NC_56 VCC_1 NC_66 VCC_1 NC_77 VDDF_1 NC_77 F5 K2
50V K7 G2 F5 K2 F5 K2 F5 K2 VCC_2 NC_67
NC_81 NC_57 VCC_2 NC_67 VCC_2 NC_78 VDDF_2 NC_78 J10 K3
K10 G12 J10 K3 J10 K3 J10 K3 VCC_3 NC_68
AR8100-*1 AR8101-*1 AR8102-*1 NC_82 NC_60 VCC_3 NC_68 VCC_3 NC_79 VDDF_3 NC_79 K9 K12
100 100 100 P7 G13 K9 K12 K9 K12 K9 K12 VCC_4 NC_69
1/16W 1/16W 1/16W NC_116 NC_61 VCC_4 NC_69 VCC_4 NC_83 VDDF_4 NC_83 K13
EMMC_SERIAL_100

EMMC_SERIAL_100

EMMC_SERIAL_100

P10 G14 K13 K13 K13 NC_70

NC_119 NC_62 NC_70 NC_84 NC_84 K14
H1 K14 K14 K14 NC_71
NC_63 NC_71 NC_85 NC_85 C2 L1
H2 C2 L1 C2 L1 C2 L1 VDDI NC_72
NC_64 VDDI NC_72 VDDI NC_86 VDDI NC_86 L2
K5 H3 L2 L2 L2 NC_73
RESET NC_65 NC_73 NC_87 NC_87 L3
H12 L3 L3 L3 NC_74
C8100 NC_67 NC_74 NC_88 NC_88 E7 L12
OPT 0.1uF H13 E7 L12 E7 L12 C4 L12 VSS_1 NC_75
NC_68 VSS_1 NC_75 VSS_1 NC_89 VSS_1 NC_89 G5 L13
16V C6 H14 G5 L13 G5 L13 E7 L13 VSS_2 NC_76
VCCQ_1 NC_69 VSS_2 NC_76 VSS_2 NC_90 VSS_2 NC_90 H10 L14
3.3V_EMMC 3.3V_EMMC M4 J1 H10 L14 H10 L14 G5 L14 VSS_3 NC_77
N4
VCCQ_2 HYNIX_EMMC_4GB NC_70
J2 K8
VSS_3 NC_77
M1 K8
VSS_3 NC_91
M1 H10
VSS_3 NC_91
M1
K8
VSS_4 NC_78
M1
VCCQ_3 NC_71 VSS_4 NC_78 VSS_4 NC_92 VSS_4 NC_92 C4 M2
P3 J3 C4 M2 C4 M2 K8 M2 VSSQ_1 NC_79
VCCQ_4 NC_72 VSSQ_1 NC_79 VSSQ_1 NC_93 VSS_5 NC_93 N2 M3
P5 J12 N2 M3 N2 M3 N2 M3 VSSQ_2 NC_80
VCCQ_5 NC_74 VSSQ_2 NC_80 VSSQ_2 NC_94 VSS_6 NC_94 N5 M7
DAT6

EMMC_CLK_BALL

EMMC_CMD_BALL

EMMC_RESET_BALL
DAT3

DAT4

DAT5

J13 N5 M7 N5 M7 N5 M7 VSSQ_3 NC_81

C8105 C8106 NC_75 VSSQ_3 NC_81 VSSQ_3 NC_95 VSS_7 NC_95 P4 M8
0.1uF 2.2uF J14 EMMC_RESET_BALL P4 M8 P4 M8 P4 M8 VSSQ_4 NC_82
NC_76 VSSQ_4 NC_82 VSSQ_4 NC_96 VSS_8 NC_96 P6 M9
16V 10V E6 K1 P6 M9 P6 M9 P6 M9 VSSQ_5 NC_83
VCC_1 NC_77 VSSQ_5 NC_83 VSSQ_5 NC_97 VSS_9 NC_97 M10
F5 K2 M10 M10 M10 NC_84
VCC_2 NC_78 NC_84 NC_98 NC_98 M11
J10 K3 M11 M11 M11 NC_85
VCC_3 NC_79 NC_85 NC_99 NC_99 M12
K9 K12 M12 M12 M12 NC_86
VCC_4 NC_83 NC_86 NC_100 NC_100 A1 M13
K13 A1 M13 A1 M13 A1 M13 NC_1 NC_87
NC_84 NC_1 NC_87 NC_1 NC_101 NC_1 NC_101 A2 M14
EMMC_VDDI K14 A2 M14 A2 M14 A2 M14 NC_2 NC_88
NC_85 NC_2 NC_88 NC_2 NC_102 NC_2 NC_102 A8 N1
C2 L1 A8 N1 A8 N1 A8 N1 NC_3 NC_89
VDDI NC_86 NC_3 NC_89 NC_5 NC_103 NC_5 NC_103 A9 N3
L2 A9 N3 A9 N3 A9 N3 NC_4 NC_90
C8104 105C NC_87 NC_4 NC_90 NC_6 NC_104 NC_6 NC_104 A10 N6
1uF L3 A10 N6 A10 N6 A10 N6 NC_5 NC_91
NC_88 NC_5 NC_91 NC_7 NC_105 NC_7 NC_105 A11 N7
6.3V E7 L12 A11 N7 A11 N7 A11 N7 NC_6 NC_92
VSS_1 NC_89 NC_6 NC_92 NC_8 NC_106 NC_8 NC_106 A12 N8
G5 L13 A12 N8 A12 N8 A12 N8 NC_7 NC_93
VSS_2 NC_90 NC_7 NC_93 NC_9 NC_107 NC_9 NC_107 A13 N9
H10 L14 A13 N9 A13 N9 A13 N9 NC_8 NC_94
VSS_3 NC_91 NC_8 NC_94 NC_10 NC_108 NC_10 NC_108 A14 N10
K8 M1 A14 N10 A14 N10 A14 N10 NC_9 NC_95
VSS_4 NC_92 NC_9 NC_95 NC_11 NC_109 NC_11 NC_109 B1 N11
C8102 C8103 C4 M2 B1 N11 B1 N11 B1 N11 NC_10 NC_96
0.1uF 2.2uF VSSQ_1 NC_93 NC_10 NC_96 NC_12 NC_110 NC_12 NC_110 B7 N12
N2 M3 B7 N12 B7 N12 B7 N12 NC_11 NC_97
16V 10V VSSQ_2 NC_94 NC_11 NC_97 NC_13 NC_111 NC_13 NC_111 B8 N13
N5 M7 B8 N13 B8 N13 B8 N13 NC_12 NC_98
VSSQ_3 NC_95 NC_12 NC_98 NC_14 NC_112 NC_14 NC_112 B9 N14
P4 M8 B9 N14 B9 N14 B9 N14 NC_13 NC_99
VSSQ_4 NC_96 NC_13 NC_99 NC_15 NC_113 NC_15 NC_113 B10 P1
P6 M9 B10 P1 B10 P1 B10 P1 NC_14 NC_100
VSSQ_5 NC_97 NC_14 NC_100 NC_16 NC_114 NC_16 NC_114 B11 P2
M10 B11 P2 B11 P2 B11 P2 NC_15 NC_101
NC_98 NC_15 NC_101 NC_17 NC_115 NC_17 NC_115 B12 P8
M11 B12 P8 B12 P8 B12 P8 NC_16 NC_102
NC_99 NC_16 NC_102 NC_18 NC_117 NC_18 NC_117 B13 P9
M12 B13 P9 B13 P9 B13 P9 NC_17 NC_103
NC_100 NC_17 NC_103 NC_19 NC_118 NC_19 NC_118 B14 P11
A1 M13 B14 P11 B14 P11 B14 P11 NC_18 NC_104
DAT3 NC_1 NC_101 NC_18 NC_104 NC_20 NC_120 NC_20 NC_120 C1 P12
A2 M14 C1 P12 C1 P12 C1 P12 NC_19 NC_105
DAT4 NC_2 NC_102 NC_19 NC_105 NC_21 NC_121 NC_21 NC_121 C3 P13
A8 N1 C3 P13 C3 P13 C3 P13 NC_20 NC_106
NC_5 NC_103 NC_20 NC_106 NC_22 NC_122 NC_22 NC_122 C7 P14
A9 N3 EMMC_CMD_BALL C7 P14 C7 P14 C7 P14 NC_22 NC_107
NC_6 NC_104 NC_22 NC_107 NC_24 NC_123 NC_24 NC_123
A10 N6
NC_7 NC_105
A11 N7
NC_8 NC_106
A12 N8
NC_9 NC_107
A13 N9
NC_10 NC_108
A14 N10
NC_11 NC_109
B1 N11
NC_12 NC_110
B7 N12
NC_13 NC_111
B8 N13
NC_14 NC_112
B9 N14
NC_15 NC_113
B10 P1
NC_16 NC_114
B11 P2 EMMC_CLK_BALL
NC_17 NC_115

Don’t Connect Power At VDDI EMMC_VDDI

B12
B13
B14
NC_18
NC_19
NC_117
NC_118
P8
P9
P11
IC8100-*5
KLM4G1FE3B-B001
IC8100-*6
THGBM5G6A2JBAIR
IC8100-*7
KLMAG2GE4A-A001
A3
IC8100-*8
H26M42002GMR

C8 A3
IC8100-*9
MTFC4GMVEA-1M WT

C8
EMMC 4.5Ver
NC_20 NC_120 A3 C8 A3 C8 A3 C8
A4
DAT0
DAT1
NC_25
NC_26
C9 A4
DAT0 NC_23
C9
C1 P12 A4
DAT0 NC_25
C9 A4
DAT0 NC_23
C9 A4
DAT0 NC_22
C9
A5
DAT2
C10 A5
DAT1 NC_24
C10

SAMSUNG_EMMC_16G
NC_27
A5
DAT1 NC_26
C10 A5
DAT1 NC_24
C10 A5
DAT1 NC_23
C10 B2 C11 DAT2 NC_25
NC_21 NC_121 DAT2 NC_27 DAT2 NC_25 DAT2 NC_24
B3
DAT3 NC_28
C12
B2
DAT3 NC_26
C11

HYNIX_EMMC_8GB
B2 C11 B2 C11 B2 C11

(Just Interal LDO Capacitor) C3 P13 DAT4 NC_29 B3 C12

DAT3 NC_28 DAT3 NC_26 DAT3 NC_25
B3 C12 B3 C12 B3 C12 B4 C13 DAT4 NC_27
SAMSUNG_EMMC_4GB

TOSHIBA_EMMC_8GB

DAT4 NC_29 DAT4 NC_27 DAT4 NC_26 DAT5 NC_30

B4 C13 B4 C13 B4 C13 B4 C13
DAT5 NC_22 NC_122 B5
DAT5
DAT6
NC_30
NC_31
C14 B5
DAT5
DAT6
NC_28
NC_29
C14 B5
DAT5
DAT6
NC_27
NC_28
C14
B5
B6
DAT6 NC_31
C14
D1 B5
DAT5 NC_28
C14 IC8100-*10 IC8100-*11 IC8100-*12
C7 P14 B6
DAT7 NC_32
D1
D2
B6
DAT7 NC_30
D1
D2
B6
DAT7 NC_29
D1
D2
DAT7 NC_32
D2 B6
DAT6 NC_29
D1
MTFC4GMCDM-1M WT THGBMAG5A1JBAIR H26M31003GMR

MICRON_EMMC_4GB
NC_33 NC_31 NC_30 NC_33 DAT7 NC_30
NC_24 NC_123 D3 D2

DEV_EMMC4.5_TOSHIBA_4G
D3 D3 D3

DEV_EMMC4.5_MICRON_4G
NC_34 NC_32 NC_31 NC_34 NC_31
M6 D4 M6 D4 M6 D4 M6 D4 D3 A3 C8 A3 C8 A3 C8
CLK NC_35 CLK NC_33 CLK NC_32 CLK NC_35 DAT0 NC_23 DAT0 NC_23 DAT0 NC_23

DEV_EMMC4.5_SKHynix_4G
M5 D12 M5 D12 M5 D12 M5 D12 NC_32 A4 C9 A4 C9 A4 C9
CMD NC_36
D13
CMD NC_34
D13
CMD NC_33
D13 CMD NC_36 M6 D4 A5
DAT1 NC_24
C10 A5
DAT1 NC_24
C10 A5
DAT1 NC_24
C10
NC_37 NC_35 NC_34 D13 CLK NC_33 DAT2 NC_25 DAT2 NC_25 DAT2 NC_25
D14 D14 D14 NC_37 M5 D12 B2 C11 B2 C11 B2 C11
NC_38 NC_36 NC_35 D14 CMD NC_34 DAT3 NC_26 DAT3 NC_26 DAT3 NC_26
A6 E1 A6 E1 A6 E1 NC_38 D13 B3 C12 B3 C12 B3 C12
NC_3 NC_39 RFU_1 NC_37 RFU_1 NC_36 A6 E1 DAT4 NC_27 DAT4 NC_27 DAT4 NC_27
A7 E2 A7 E2 A7 E2 NC_3 NC_39 NC_35 B4 C13 B4 C13 B4 C13
C5
NC_4 NC_40
E3 C5
RFU_2 NC_38
E3 C5
RFU_2 NC_37
E3 A7 E2 D14 B5
DAT5 NC_28
C14 B5
DAT5 NC_28
C14 B5
DAT5 NC_28
C14
NC_23 NC_41 NC_21 NC_39 RFU_3 NC_38 NC_4 NC_40 NC_36 DAT6 NC_29 DAT6 NC_29 DAT6 NC_29
E5 E12 E5 E12 E5 E12 C5 E3 A6 E1 B6 D1 B6 D1 B6 D1
E8
NC_42 NC_46
E13 E8
RFU_3 NC_40
E13 E8
RFU_4 NC_40
E13
NC_23 NC_41 RFU_1 NC_37 DAT7 NC_30
D2
DAT7 NC_30
D2
DAT7 NC_30
D2
E5 E12 A7 E2
NC_43 NC_47 RFU_4 NC_41 RFU_5 NC_41 NC_42 NC_46 NC_31 NC_31 NC_31
E9 E14 E9 E14 E9 E14 E8 E13 RFU_2 NC_38 D3 D3 D3
E10
NC_44 NC_48
F1 E10
RFU_5 NC_42
F1 E10
RFU_6 NC_42
F1 NC_43 NC_47
C5 E3 M6
NC_32
D4 M6
NC_32
D4 M6
NC_32
D4
NC_45 NC_49 RFU_6 NC_43 NC_39 NC_43 E9 E14 NC_21 NC_39 CLK NC_33 CLK NC_33 CLK NC_33
F10 F2 F10 F2 F10 F2 NC_44 NC_48 E5 E12 M5 D12 M5 D12 M5 D12
G3
NC_52 NC_50
F3 G3
RFU_7 NC_44
F3 G3
RFU_7 NC_44
F3
E10 F1 RFU_3 NC_40 CMD NC_34
D13
CMD NC_34
D13
CMD NC_34
D13
NC_58 NC_51 RFU_8 NC_45 RFU_8 NC_45 NC_45 NC_49 E8 E13 NC_35 NC_35 NC_35
G10 F12 G10 F12 G10 F12 F10 F2 RFU_4 NC_41 D14 D14 D14
NC_52 NC_50 E9 E14
DU1 DU9 H5
J5
NC_59
NC_66
NC_53
NC_54
F13
F14
H5
J5
RFU_9
RFU_10
NC_46
NC_47
F13
F14
H5
J5
RFU_9
RFU_10
NC_46
NC_47
F13
F14
G3
G10
NC_58 NC_51
F3
F12 E10
RFU_5 NC_42
F1
A6
A7
RFU_1
NC_36
NC_37
E1
E2
A6
A7
RFU_1
NC_36
NC_37
E1
E2
A6
A7
RFU_1
NC_36
NC_37
E1
E2

DUMMY_1 DUMMY_9 K6
NC_73
NC_80
NC_55
NC_56
G1 K6
RFU_11
RFU_12
NC_48
NC_49
G1 K6
RFU_11
RFU_12
NC_48
NC_49
G1 H5
NC_59 NC_53
F13 F10
RFU_6 NC_43
F2 C5
RFU_2
NC_21
NC_38
NC_39
E3 C5
RFU_2
NC_21
NC_38
NC_39
E3 C5
RFU_2
NC_21
NC_38
NC_39
E3

DU2 DU10 K7
K10
NC_81
NC_82
NC_57
NC_60
G2
G12
K7
K10
RFU_13
RFU_14
NC_50
NC_51
G2
G12
K7
K10
RFU_13
RFU_14
NC_50
NC_51
G2
G12
J5
K6
NC_66
NC_73
NC_54
NC_55
F14
G1
G3
RFU_7
RFU_8
NC_44
NC_45
F3
E5
E8
RFU_3
RFU_4
NC_40
NC_41
E12
E13
E5
E8
RFU_3
RFU_4
NC_40
NC_41
E12
E13
E5
E8
RFU_3
RFU_4
NC_40
NC_41
E12
E13

DUMMY_2 DUMMY_10 P7
P10
NC_116 NC_61
G13
G14
P7
P10
RFU_15 NC_52
G13
G14
P7
P10
RFU_15 NC_52
G13
G14 K7
NC_80 NC_56
G2
G10
H5
RFU_9 NC_46
F12
F13
E9
E10
RFU_5 NC_42
E14
F1
E9
E10
RFU_5 NC_42
E14
F1
E9
E10
RFU_5 NC_42
E14
F1
DU3 DU11 NC_119 NC_62
NC_63
H1
H2
RFU_16 NC_53
NC_54
H1
H2
NC_104 NC_53
NC_54
H1
H2
K10
P7
NC_81
NC_82
NC_57
NC_60
G12
G13
J5
RFU_10 NC_47
F14
F10
G3
RFU_6
RFU_7
NC_43
NC_44
F2
F3
F10
G3
RFU_6
RFU_7
NC_43
NC_44
F2
F3
F10
G3
RFU_6
RFU_7
NC_43
NC_44
F2
F3
DUMMY_3 DUMMY_11 K5
NC_64
H3 K5
NC_55
H3 K5
NC_55
H3 P10
NC_116 NC_61
G14 K6
RFU_11 NC_48
G1 G10
RFU_8 NC_45
F12 G10
RFU_8 NC_45
F12 G10
RFU_8 NC_45
F12

DU4 DU12 RSTN NC_65

NC_67
H12
H13
RSTN NC_56
NC_57
H12
H13
RESET NC_56
NC_57
H12
H13
NC_119 NC_62
NC_63
H1 K7
RFU_12
RFU_13
NC_49
NC_50
G2 H5
J5
RFU_9
RFU_10
NC_46
NC_47
F13
F14
H5
J5
RFU_9
RFU_10
NC_46
NC_47
F13
F14
H5
J5
RFU_9
RFU_10
NC_46
NC_47
F13
F14

DUMMY_4 DUMMY_12 C6
VDD_1
NC_68
NC_69
H14 C6
VCCQ_1
NC_58
NC_59
H14 C6
VDD_1
NC_58
NC_59
H14
K5
NC_64
H2
H3
K10
P7
RFU_14 NC_51
G12
G13
K6
RFU_11
RFU_12
NC_48
NC_49
G1 K6
RFU_11
RFU_12
NC_48
NC_49
G1 K6
RFU_11
RFU_12
NC_48
NC_49
G1

DU5 DU13 M4
N4
VDD_2
VDD_3
NC_70
NC_71
J1
J2
M4
N4
VCCQ_2
VCCQ_3
NC_60
NC_61
J1
J2
M4
N4
VDD_2
VDD_3
NC_60
NC_61
J1
J2
RESET NC_65
NC_67
H12 P10
RFU_15 NC_52
G14
K7
K10
RFU_13
RFU_14
NC_50
NC_51
G2
G12
K7
K10
RFU_13
RFU_14
NC_50
NC_51
G2
G12
K7
K10
RFU_13
RFU_14
NC_50
NC_51
G2
G12

DUMMY_5 DUMMY_13 P3
P5
VDD_4 NC_72
J3
J12
P3
P5
VCCQ_4 NC_62
J3
J12
P3
P5
VDD_4 NC_62
J3
J12 NC_68
H13 RFU_16 NC_53
H1
P7
P10
RFU_15 NC_52
G13
G14
P7
P10
RFU_15 NC_52
G13
G14
P7
P10
RFU_15 NC_52
G13
G14
DU6 DU14 VDD_5 NC_74
NC_75
J13
J14
VCCQ_5 NC_63
NC_64
J13
J14
VDD_5 NC_63
NC_64
J13
J14
C6
M4
VCCQ_1
VCCQ_2
NC_69
NC_70
H14
J1
NC_54
NC_55
H2 RFU_16 NC_53
NC_54
H1
H2
RFU_16 NC_53
NC_54
H1
H2
RFU_16 NC_53
NC_54
H1
H2
DUMMY_6 DUMMY_14 E6
NC_76
K1 E6
NC_65
K1 E6
NC_65
K1
N4
VCCQ_3 NC_71
J2 K5
RSTN NC_56
H3
H12
K5
NC_55
H3 K5
NC_55
H3 K5
NC_55
H3

DU7 DU15 F5
J10
VDDF_1
VDDF_2
NC_77
NC_78
K2
K3
F5
J10
VCC_1
VCC_2
NC_66
NC_67
K2
K3
F5
J10
VDDF_1
VDDF_2
NC_66
NC_67
K2
K3
P3
P5
VCCQ_4 NC_72
J3
J12
NC_57
H13
RST_N NC_56
NC_57
H12
H13
RST_N NC_56
NC_57
H12
H13
RST_N NC_56
NC_57
H12
H13

DUMMY_7 DUMMY_15 K9
VDDF_3
VDDF_4
NC_79
NC_83
K12 K9
VCC_3
VCC_4
NC_68
NC_69
K12 K9
VDDF_3
VDDF_4
NC_68
NC_69
K12
VCCQ_5 NC_74
NC_75
J13 C6
NC_58
H14 C6
VCCQ_1
NC_58
NC_59
H14 C6
VCCQ_1
NC_58
NC_59
H14 C6
VCCQ_1
NC_58
NC_59
H14

DU8 DU16 NC_84

NC_85
K13
K14
NC_70
NC_71
K13
K14
NC_70
NC_71
K13
K14
E6
NC_76
J14
K1
M4
VCCQ_1
VCCQ_2
NC_59
NC_60
J1
M4
N4
VCCQ_2
VCCQ_3
NC_60
NC_61
J1
J2
M4
N4
VCCQ_2
VCCQ_3
NC_60
NC_61
J1
J2
M4
N4
VCCQ_2
VCCQ_3
NC_60
NC_61
J1
J2

DUMMY_8 DUMMY_16 C2
VDDI NC_86
NC_87
L1
L2
C2
VDDI NC_72
NC_73
L1
L2
C2
VDDI NC_72
NC_73
L1
L2
F5
J10
VCC_1
VCC_2
NC_77
NC_78
K2
N4
P3
VCCQ_3 NC_61
J2
J3
P3
P5
VCCQ_4
VCCQ_5
NC_62
NC_63
J3
J12
P3
P5
VCCQ_4
VCCQ_5
NC_62
NC_63
J3
J12
P3
P5
VCCQ_4
VCCQ_5
NC_62
NC_63
J3
J12
L3 L3 L3 K3 VCCQ_4 NC_62 J13 J13 J13
NC_88 NC_74 NC_74 VCC_3 NC_79 P5 J12 NC_64 NC_64 NC_64
E7 L12 E7 L12 E7 L12 K9 K12 J14 J14 J14
VSS_2 NC_89 VSS_1 NC_75 VSS_2 NC_75 VCC_4 NC_83 VCCQ_5 NC_63 NC_65 NC_65 NC_65
G5 L13 G5 L13 G5 L13 K13 J13 E6 K1 E6 K1 E6 K1
H10
VSS_3 NC_90
L14 H10
VSS_2 NC_76
L14 H10
VSS_3 NC_76
L14 NC_84 NC_64 F5
VCC_1 NC_66
K2 F5
VCC_1 NC_66
K2 F5
VCC_1 NC_66
K2
VSS_4 NC_91 VSS_3 NC_77 VSS_4 NC_77 K14 J14 VCC_2 NC_67 VCC_2 NC_67 VCC_2 NC_67
K8 M1 K8 M1 K8 M1 NC_85 NC_65 J10 K3 J10 K3 J10 K3
VSS_5 NC_92 VSS_4 NC_78 VSS_9 NC_78 C2 L1 E6 K1 VCC_3 NC_68 VCC_3 NC_68 VCC_3 NC_68
C4 M2 C4 M2 C4 M2 VDDI NC_86 K9 K12 K9 K12 K9 K12
VSS_1 NC_93 VSSQ_1 NC_79 VSS_1 NC_79 L2 VCC_1 NC_66 VCC_4 NC_69 VCC_4 NC_69 VCC_4 NC_69
N2 M3 N2 M3 N2 M3 NC_87
F5 K2 K13 K13 K13
N5
VSS_6 NC_94
M7 N5
VSSQ_2 NC_80
M7 N5
VSS_5 NC_80
M7 L3 VCC_2 NC_67 NC_70
K14
NC_70
K14
NC_70
K14
VSS_7 NC_95 VSSQ_3 NC_81 VSS_6 NC_81 NC_88 J10 K3 NC_71 NC_71 NC_71
P4 M8 P4 M8 P4 M8 E7 L12 VCC_3 NC_68 C2 L1 C2 L1 C2 L1
P6
VSS_8 NC_96
M9 P6
VSSQ_4 NC_82
M9 P6
VSS_7 NC_82
M9
VSS_1 NC_89 K9 K12 VDDI NC_72
L2
VDDI NC_72
L2
VDDI NC_72
L2
G5 L13 VCC_4 NC_69
VSS_9 NC_97 VSSQ_5 NC_83 VSS_8 NC_83 VSS_2 NC_90 NC_73 NC_73 NC_73
M10 M10 M10 H10 L14 K13 L3 L3 L3
NC_98
M11
NC_84
M11
NC_84
M11 VSS_3 NC_91 NC_70 E7
NC_74
L12 E7
NC_74
L12 E7
NC_74
L12
NC_99 NC_85 NC_85 K8 M1 K14 VSS_1 NC_75 VSS_1 NC_75 VSS_1 NC_75
M12 M12 M12 VSS_4 NC_92 NC_71 G5 L13 G5 L13 G5 L13
A1
NC_100
M13 A1
NC_86
M13 A1
NC_86
M13
C4 M2 C2 L1 H10
VSS_2 NC_76
L14 H10
VSS_2 NC_76
L14 H10
VSS_2 NC_76
L14
NC_1 NC_101 NC_1 NC_87 NC_1 NC_87 VSSQ_1 NC_93 VDDI NC_72 VSS_3 NC_77 VSS_3 NC_77 VSS_3 NC_77
A2 M14 A2 M14 A2 M14 N2 M3 L2 K8 M1 K8 M1 K8 M1
NC_2 NC_102 NC_2 NC_88 NC_2 NC_88 VSSQ_2 NC_94 NC_73 VSS_4 NC_78 VSS_4 NC_78 VSS_4 NC_78
A8 N1 A8 N1 A8 N1 N5 M7 L3 C4 M2 C4 M2 C4 M2
NC_5 NC_103 NC_3 NC_89 NC_3 NC_89 VSSQ_3 NC_95 VSSQ_1 NC_79 VSSQ_1 NC_79 VSSQ_1 NC_79
A9 N3 A9 N3 A9 N3 P4 M8 NC_74 N2 M3 N2 M3 N2 M3
A10
NC_6 NC_104
N6 A10
NC_4 NC_90
N6 A10
NC_4 NC_90
N6 VSSQ_4 NC_96 E7 L12 N5
VSSQ_2 NC_80
M7 N5
VSSQ_2 NC_80
M7 N5
VSSQ_2 NC_80
M7
NC_7 NC_105 NC_5 NC_91 NC_5 NC_91 P6 M9 VSS_1 NC_75 VSSQ_3 NC_81 VSSQ_3 NC_81 VSSQ_3 NC_81
A11 N7 A11 N7 A11 N7 VSSQ_5 NC_97 G5 L13 P4 M8 P4 M8 P4 M8
NC_8 NC_106 NC_6 NC_92 NC_6 NC_92 M10 VSS_2 NC_76 VSSQ_4 NC_82 VSSQ_4 NC_82 VSSQ_4 NC_82
A12 N8 A12 N8 A12 N8 NC_98 H10 L14 P6 M9 P6 M9 P6 M9
NC_9 NC_107 NC_7 NC_93 NC_7 NC_93 M11 VSSQ_5 NC_83 VSSQ_5 NC_83 VSSQ_5 NC_83
A13 N9 A13 N9 A13 N9 NC_99 VSS_3 NC_77 M10 M10 M10
A14
NC_10 NC_108
N10 A14
NC_8 NC_94
N10 A14
NC_8 NC_94
N10 M12 K8 M1 NC_84
M11
NC_84
M11
NC_84
M11
NC_11 NC_109 NC_9 NC_95 NC_9 NC_95 NC_100 VSS_4 NC_78 NC_85 NC_85 NC_85
B1 N11 B1 N11 B1 N11 A1 M13 C4 M2 M12 M12 M12
B7
NC_12 NC_110
N12 B7
NC_10 NC_96
N12 B7
NC_10 NC_96
N12
NC_1 NC_101 VSSQ_1 NC_79 A1
NC_86
M13 A1
NC_86
M13 A1
NC_86
M13
A2 M14 N2 M3
NC_13 NC_111 NC_11 NC_97 NC_11 NC_97 NC_2 NC_102 NC_1 NC_87 NC_1 NC_87 NC_1 NC_87
B8 N13 B8 N13 B8 N13 A8 N1 VSSQ_2 NC_80 A2 M14 A2 M14 A2 M14
B9
NC_14 NC_112
N14 B9
NC_12 NC_98
N14 B9
NC_12 NC_98
N14 NC_5 NC_103
N5 M7 A8
NC_2 NC_88
N1 A8
NC_2 NC_88
N1 A8
NC_2 NC_88
N1
NC_15 NC_113 NC_13 NC_99 NC_13 NC_99 A9 N3 VSSQ_3 NC_81 NC_3 NC_89 NC_3 NC_89 NC_3 NC_89
B10 P1 B10 P1 B10 P1 NC_6 NC_104 P4 M8 A9 N3 A9 N3 A9 N3
B11
NC_16 NC_114
P2 B11
NC_14 NC_100
P2 B11
NC_14 NC_100
P2
A10 N6 VSSQ_4 NC_82 A10
NC_4 NC_90
N6 A10
NC_4 NC_90
N6 A10
NC_4 NC_90
N6
NC_17 NC_115 NC_15 NC_101 NC_15 NC_101 NC_7 NC_105 P6 M9 NC_5 NC_91 NC_5 NC_91 NC_5 NC_91
B12 P8 B12 P8 B12 P8 A11 N7 VSSQ_5 NC_83 A11 N7 A11 N7 A11 N7
NC_18 NC_117 NC_16 NC_102 NC_16 NC_102 NC_8 NC_106 M10 NC_6 NC_92 NC_6 NC_92 NC_6 NC_92
B13 P9 B13 P9 B13 P9 A12 N8 A12 N8 A12 N8 A12 N8
NC_19 NC_118 NC_17 NC_103 NC_17 NC_103 NC_9 NC_107 NC_84 NC_7 NC_93 NC_7 NC_93 NC_7 NC_93
B14 P11 B14 P11 B14 P11 A13 N9 M11 A13 N9 A13 N9 A13 N9
C1
NC_20 NC_120
P12 C1
NC_18 NC_104
P12 C1
NC_18 RFU_16
P12 NC_10 NC_108 NC_85 A14
NC_8 NC_94
N10 A14
NC_8 NC_94
N10 A14
NC_8 NC_94
N10
NC_21 NC_121 NC_19 NC_105 NC_19 NC_105 A14 N10 M12 NC_9 NC_95 NC_9 NC_95 NC_9 NC_95
C3 P13 C3 P13 C3 P13 NC_11 NC_109 NC_86 B1 N11 B1 N11 B1 N11
NC_22 NC_122 NC_20 NC_106 NC_20 NC_106 B1 N11 A1 M13 NC_10 NC_96 NC_10 NC_96 NC_10 NC_96
C7 P14 C7 P14 C7 P14 NC_12 NC_110 B7 N12 B7 N12 B7 N12
NC_24 NC_123 NC_22 NC_107 NC_21 NC_107 B7 N12 NC_1 NC_87 NC_11 NC_97 NC_11 NC_97 NC_11 NC_97
NC_13 NC_111
A2 M14 B8 N13 B8 N13 B8 N13
B8 N13 NC_2 NC_88 B9
NC_12 NC_98
N14 B9
NC_12 NC_98
N14 B9
NC_12 NC_98
N14
NC_14 NC_112 A8 N1 NC_13 NC_99 NC_13 NC_99 NC_13 NC_99
B9 N14 NC_3 NC_89 B10 P1 B10 P1 B10 P1
NC_15 NC_113 A9 N3 B11
NC_14 NC_100
P2 B11
NC_14 NC_100
P2 B11
NC_14 NC_100
P2
B10 P1 NC_4 NC_90
NC_16 NC_114 NC_15 NC_101 NC_15 NC_101 NC_15 NC_101
DU1 DU9 B11 P2 A10 N6 B12 P8 B12 P8 B12 P8
DU2
DUMMY_1 DUMMY_9
DU10 NC_17 NC_115 NC_5 NC_91 B13
NC_16 NC_102
P9 B13
NC_16 NC_102
P9 B13
NC_16 NC_102
P9
DUMMY_2 DUMMY_10 B12 P8 A11 N7 NC_17 NC_103 NC_17 NC_103 NC_17 NC_103
DU3 DU11 NC_18 NC_117 NC_6 NC_92 B14 P11 B14 P11 B14 P11
DU4
DUMMY_3 DUMMY_11
DU12
B13 P9 A12 N8 C1
NC_18 NC_104
P12 C1
NC_18 NC_104
P12 C1
NC_18 NC_104
P12
DUMMY_4 DUMMY_12 NC_19 NC_118 NC_7 NC_93 NC_19 NC_105 NC_19 NC_105 NC_19 NC_105
DU5 DU13 B14 P11 A13 N9 C3 P13 C3 P13 C3 P13
DUMMY_5 DUMMY_13 NC_20 NC_120 NC_8 NC_94 NC_20 NC_106 NC_20 NC_106 NC_20 NC_106
DU6 DU14 C1 P12 A14 N10 C7 P14 C7 P14 C7 P14
DUMMY_6 DUMMY_14 NC_21 NC_121 NC_22 NC_107 NC_22 NC_107 NC_22 NC_107
DU7 DU15 C3 P13 NC_9 NC_95
DU8
DUMMY_7 DUMMY_15
DU16 NC_22 NC_122 B1 N11
DUMMY_8 DUMMY_16 C7 P14 NC_10 NC_96
NC_24 NC_123 B7 N12
NC_11 NC_97
B8 N13
NC_12 NC_98
B9 N14
NC_13 NC_99
B10 P1
NC_14 NC_100
B11 P2
NC_15 NC_101
B12 P8
NC_16 NC_102
B13 P9
NC_17 NC_103
B14 P11
NC_18 NC_104
C1 P12
NC_19 NC_105
C3 P13

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

NC_20 NC_106
C7 P14
NC_22 NC_107

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS eMMC 11.09.29
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
81
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 +24V_AMP

OPT
C5450
10uF
35V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 USE Two serial TS Port for Japan : MTK
JAPAN TUNER INTERFACE
A2 Ball Name Function

FE_DEMOD1_TS_DATA[1] FE_DEMOD1_TS_DATA[1] DEMOD_TSCLK Ext_TS_CLK

R8500 0
FE_DEMOD3_TS_CLK
TU_J_JP
FE_DEMOD1_TS_DATA[3] FE_DEMOD1_TS_DATA[3] DEMOD_TSSYNC Ext_TS_Sync
R8501 0
FE_DEMOD3_TS_SYNC
TU_J_JP
FE_DEMOD1_TS_DATA[4] FE_DEMOD1_TS_DATA[4] DEMOD_TSDATA0 Ext_Ts_D0
R8502 0
FE_DEMOD3_TS_DATA
TU_J_JP
FE_DEMOD1_TS_DATA[2] FE_DEMOD1_TS_DATA[2] DEMOD_TSVAL Ext_Ts_VAL
R8506 0
FE_DEMOD3_TS_VAL
TU_J_JP

FE_DEMOD1_TS_CLK FE_DEMOD1_TS_CLK DEMOD_TSDATA1 EXT2_Ts_CLK

R8503 0
FE_DEMOD2_TS_CLK
TU_J_JP
FE_DEMOD1_TS_SYNC FE_DEMOD1_TS_SYNC DEMOD_TSDATA3 EXT2_TS_Sync
R8504 0
FE_DEMOD2_TS_SYNC
TU_J_JP
FE_DEMOD1_TS_DATA[0] FE_DEMOD1_TS_DATA[0] DEMOD_TSDATA4 EXT2_TS_D0
R8505 0
FE_DEMOD2_TS_DATA
TU_J_JP
FE_DEMOD1_TS_VAL FE_DEMOD1_TS_VAL DEMOD_TSDATA2 EXT2_TS_Val
R8507 0
FE_DEMOD2_TS_VAL
TU_J_JP

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
2012.06.15
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR 85
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 M13 EAX64872104 BASE M13 PCB P/NO C114-*2
3.3pF
C115-*2 C114-*1 C115-*1
3.3pF 2.7pF
14y Smart TV EAX64797001* : LD33B
50V
EAX6558850X_3.3pF
50V
EAX6558850X_3.3pF
50V
2.7pF
50V
EAX6561020X_2.7pF EAX6561020X_2.7pF

EAX64872101* : LA33B X-TAL X100

27MHz
X-TAL_1 GND_2
MT5398_XTAL_IN 1 4
Close to eMMC Flash C114
GND_1 X-TAL_2
EAX6561090X_1pF 1.0pF 2 3 MT5398_XTAL_OUT
IC100-*1
(IC8100) 50V C115
M24256-BRMN6TP 1.0pF EAX6561090X_1pF
+3.3V_NORMAL
NVRAM E0
1 8
VCC NC4.5 PCB P/NO EMMC_CLK
50V

E1

E2
2

3
7

6
WC

SCL
NON CI : EAX65610201 R168
10K
R101
4.7K
R102
4.7K
IC100
AT24C256C-SSHL-T
+3.3V_NORMAL VSS
4 5
SDA
CI :
OPT NVRAM_ST
R100 A0 VCC
1 8 Write Protection M13 vs Lean Smart
4.7K del. FE_LNA_Ctrl1/2
OPT A1 WP - Low : Normal Operation
2 7
- High : Write Protection cause of Tuner change 13y to 14y
A2 SCL
R135 33 VDD3V3 IC105
3 6 I2C_SCL5 LGE2122[A2_M13]
+3.3V_NORMAL
GND SDA
4 5 R134 33
I2C_SDA5

R195
R194
AK10 AH15

10K
10K
L/DIM0_MOSI JTCK U0TX SOC_TX
NVRAM_ATMEL AK11 AH14
L/DIM0_SCLK JTDI U0RX SOC_RX R183 R184
AL9 4.7K 4.7K
JTDO
AJ11 AH13
JTMS U1TX M_REMOTE_TX
AJ12 AG13
L/DIM0_VS JTRST U1RX M_REMOTE_RX

HDCP EEPROM OSDA0

OSCL0
AH11
AH10
OSDA0
OSCL0
POWE
POOE
D24
B25
EMMC_CMD

D25 FE_LNA_Ctrl1/2 EMMC_DATA[2-7]

POCE1
AF11 A25
OSDA1 OSDA1 POCE0 EMMC_DATA[7]
AG11 C22
OSCL1 OSCL1 PDD7 EMMC_DATA[6]
B22
PDD6 EMMC_DATA[5]
AVDD_33SB AN29 A22
MT5398_XTAL_IN XTALI PDD5 EMMC_DATA[4]
AM29 C23 AVDD_33SB

Deleted STRAPPING LED_PWM0 LED_PWM1 OPCTRL3 OPCTRL7

MT5398_XTAL_OUT

AN30
XTALO
Wake On Lan

AVDD33_XTAL_STB
PDD4
PDD3
PDD2
A23
B23
EMMC_DATA[3]
EMMC_DATA[2]
R188
CAM_SLIDE_DET

C111 AL29 D23 4.7K

ICE mode + 27M + serial boot 1 0 0 0 0.1uF AVSS33_XTAL_STB PDD1
C24
PDD0 WOL/ETH_POWER_ON
ICE mode + 27M + ROM to Nand boot 1 0 0 1 C25 CAM_SLIDE_DET
PARB R187
AVDD_33SB A26 4.7K
+3.3V_NORMAL ICE mode + 27M + ROM to 60bit ECC Nand boot 1 0 1 0 PACLE EMMC_DATA[1]
AN17 B26 OPT +3.3V_NORMAL
AVDD33_VGA_STB PAALE EMMC_DATA[0]
ICE mode + 27M + ROM to eMMC boot from 1 0 1 1 C110 AL17 C21
0.1uF AVSS33_AVSS33_VGA_STB EMMC_CLK EMMC_CLK
EMMC pins (share pins w/s NAND)
R158 R189
VDD3V3 AL15
ICE mode + 27M + ROM to eMMC 1 1 0 0 OPWRSB 10K
R155 R157 R162 R163 AL26
1K OPT 1K 1K Boot from SDIO pins 22 OPT
1K AVDD33_PLL R186
C109 AC21 AK20
0.1uF AVSS33_PLLGP ORESET SOC_RESET
H21
LED_PWM0 AVSS33_CPUPLL 22 C117
AF17 0.1uF
LED_PWM1 OIRI
16V
OPCTRL3
AM17 C20
OPCTRL7 AVDD10_LDO FSRC_WR
C107
R154 R156 R160 4.7uF AL14
1K 1K OPT 1K OPT
R161 10V STB_SCL STB_SCL Q100 +3.3V_NORMAL
1K AN16 AK15 D100
OPT

AVDD10_ELDO STB_SDA STB_SDA R196 PMV48XP

1N4148W
C112 240

S
4.7uF AE14 R193 4.7K

R180 4.7K
10V POR_BND 100V

R190
G

10K
IC105
I2C_1 : AMP, L/DIMMING,HDCP KEY CI_ADDR[0-14]
LGE2122[A2_M13]
I2C_2 : T-CON, CI_ADDR[0-14]
I2C_3 : MICOM OTP_WRITE
CI_ADDR[0] B30 P30 FE_DEMOD1_TS_DATA[0-7]
I2C_4 : S/Demod,T2/Demod, LNB, MHL(Sil1292) GPIO0 DEMOD_RST PCM_RST
I2C R147-*1 R142-*1
I2C_5
I2C_6
:
:
NVRAM
TUNER_MOPLL(T/C,ATV)
CI_ADDR[1]
CI_ADDR[2]
A31
B31
GPIO1
GPIO2
DEMOD_TSCLK
DEMOD_TSDATA0
N32
R27
FE_DEMOD1_TS_CLK FE_DEMOD1_TS_DATA[0]
FE_DEMOD1_TS_DATA[1]
CI_ADDR[3] A32 T26
TU_Q_SG TU_Q_SG GPIO3 DEMOD_TSDATA1
1.5K 1.5K +3.3V_NORMAL CI_ADDR[4] C30 T27 FE_DEMOD1_TS_DATA[2]
R152-*1 R153-*1 GPIO4 DEMOD_TSDATA2 FE_DEMOD1_TS_DATA[3]
CI_ADDR[5] A33 P26
TU_Q_KR TU_Q_KR GPIO5 DEMOD_TSDATA3 EXTERNAL DEMOD
NON_TU_Q_SG

NON_TU_Q_SG

1.5K CI_ADDR[6] B32 R28 FE_DEMOD1_TS_DATA[4]

1.5K
NON_TU_Q_KR

NON_TU_Q_KR

GPIO6 DEMOD_TSDATA4 FE_DEMOD1_TS_DATA[5] -> SOC

CI_ADDR[7] C31 U27
R121 R124 R132 R133 R138 R141 R142 R147 R150 R151 R152-*2 R153-*2 GPIO7 DEMOD_TSDATA5 FE_DEMOD1_TS_DATA[6]
R152 R153 CI_ADDR[8] E30 U26
1.2K 1.2K 2.7K 2.7K 2.7K 2.7K 2.7K 2.7K 2.7K 2.7K TU_N_TW/BR TU_N_TW/BR SOC -> CI SLOT GPIO8 DEMOD_TSDATA6 FE_DEMOD1_TS_DATA[7]
2.7K 2.7K CI_ADDR[9] F29 R26
1.2K 1.2K GPIO9 DEMOD_TSDATA7
MT5398_MCLKI CI_ADDR[10] F27 R29
STB_SCL R120 33 I2C_SCL1 GPIO10 DEMOD_TSSYNC FE_DEMOD1_TS_SYNC
MT5398_MIVAL_ERR CI_ADDR[11] F28 P27
STB_SDA R115 33 I2C_SDA1 GPIO11 DEMOD_TSVAL FE_DEMOD1_TS_VAL
MT5398_MISTRT CI_ADDR[12] C32
OPCTRL_11_SCL R116 33 M13 vs Lean Smart CI_ADDR[13] F30
GPIO12
L25
R117 33 I2C_SCL2/SDA2 del. I2C_SCL2/SDA2 GPIO13 CI_INT /PCM_REG
OPCTRL_10_SDA CI_ADDR[14] F32 N33
SOC -> CI SLOT
OSCL1 R118 33 I2C_SCL_MICOM
cause of EPI block deletion D30
GPIO14 CI_TSCLK
K26
/PCM_CE1
MT5398_TS_OUT[0-7] GPIO15 CI_TSDATA0 MT5398_TS_SYNC CI SLOT -> SOC
OSDA1 R119 33 I2C_SDA_MICOM D32 N30 /PCM_WE
R110 33 GPIO16 CI_TSSYNC
OSCL2 I2C_SCL4 F31 N31 /PCM_OE
R111 33 GPIO17 CI_TSVAL
OSDA2 I2C_SDA4 MT5398_TS_OUT[0] F33
R112 33 GPIO18
OSCL0 I2C_SCL5 MT5398_TS_OUT[1] E31 M31
R113 33 GPIO19 PVR_TSCLK MT5398_TS_VAL CI SLOT -> SOC
OSDA0 I2C_SDA5 MT5398_TS_OUT[2] E32 M27
R114 33 GPIO20 PVR_TSVAL CI_A_VS1
OPCTRL_1_SCL I2C_SCL6 MT5398_TS_OUT[3] D31 L27
R109 33 GPIO21 PVR_TSSYNC MT5398_TS_CLK CI SLOT -> SOC
OPCTRL_0_SDA I2C_SDA6 MT5398_TS_OUT[4] D33 M29
GPIO22 PVR_TSDATA0 /PCM_IRQA
MT5398_TS_OUT[5] E29 M30
CI_DATA[0-7] GPIO23 PVR_TSDATA1 /PCM_WAIT
MT5398_TS_OUT[6] C33
GPIO24 +3.3V_NORMAL
MT5398_TS_OUT[7] B33 L30
GPIO25 SPI_CLK1 /CI_CD2
CI_DATA[0] A30 L33
GPIO26 SPI_CLK /CI_CD1
CI_DATA[1] E28 L32
GPIO27 SPI_DATA /PCM_IORD R174 R177
CI_DATA[2] C29 K27 4.7K 4.7K
GPIO28 SPI_CLE /PCM_IOWR
CI_DATA[3] J28 OPT OPT
GPIO29 R179 PWM_DIM2
+3.3V_NORMAL Model Option CI_DATA[4]
CI_DATA[5]
H29
J26
GPIO30 OPWM2
AL8
AM8 22
PWM_DIM2
GPIO31 OPWM1 PWM_DIM1
CI_DATA[6] G30 AM9 R178 22
GPIO32 OPWM0 /RST_HUB
CI_DATA[7] G27
GPIO33 R173 R176 /RST_HUB
MTK_DVB_T2_TUNER

E27 D27
MTK_DVB_S_TUNER

MT5398_TS_IN[0] 1K 1K
Country_AJJA

GPIO34 SD_D0
MTK_DDR_1.25GB

D29 C27
MODULE_V13

MTK_CP_BOX

MT5398_TS_IN[1] GPIO35 SD_D1

MTK_SMALL
FRC_120Hz

D28 D26
Country_TW

PWM2_PULL_DOWN_1K
MTK_FHD

MT5398_TS_IN[2] GPIO36 SD_D2

R140
4.7K
R137
4.7K

R145
4.7K
R130
4.7K

R146
4.7K
R131
4.7K
R123
4.7K
R106
4.7K

R108
4.7K

R149
4.7K

H28 C26 PWM1_PULL_DOWN_1K

R105
4.7K

OPT

MT5398_TS_IN[3]
CI SLOT -> SOC GPIO37 SD_D3
J27 A28
MT5398_TS_IN[4] GPIO38 SD_CMD
G29 E24
GPIO45(EMMC_RST) is dedicated to reset MT5398_TS_IN[5] GPIO39 SD_CLK
HIGH LOW G31 SMARTCARD_CLK/SD_EMMC_DATA[0]
MT5398_TS_IN[6] SMARTCARD_CLK/SD_EMMC_DATA[0]
EMMC for improving A1’s leakage current GPIO40 SMARTCARD_PWR_SEL/SD_EMMC_DATA[1]
MODEL_OPT_0 G28 SMARTCARD_PWR_SEL/SD_EMMC_DATA[1]
MT5398_TS_IN[7]
MODEL_OPT_0 Country_TW TW Non_TW GPIO41 SMARTCARD_RST/SD_EMMC_DATA[2]
/USB_OCD2 B28 SMARTCARD_RST/SD_EMMC_DATA[2]
MODEL_OPT_1 GPIO42
K28 SMARTCARD_DET/SD_EMMC_DATA[3]
MODEL_OPT_1 FRC FRC(120Hz) No FRC(60Hz) /USB_OCD1 SMARTCARD_DET/SD_EMMC_DATA[3]
MODEL_OPT_2 GPIO43 SMARTCARD_VCC/SD_EMMC_CMD
/USB_OCD3 E25 SMARTCARD_VCC/SD_EMMC_CMD
MODEL_OPT_2 Panel FHD HD GPIO44 SMARTCARD_DATA/SD_EMMC_CLK
D21 SMARTCARD_DATA/SD_EMMC_CLK
MODEL_OPT_3 EMMC_RST GPIO45
MODEL_OPT_3 Country_AJJA AJJA Non_AJJA G23
/S2_RESET USB_CTL1 GPIO46
MODEL_OPT_4 C28
MODEL_OPT_4 Module V13 V12 #SIL_RESET GPIO47
MODEL_OPT_5 F24 AF15
M13 vs Lean Smart EPI_LOCK6 AB8
GPIO48 LED_PWM1 LED_PWM1
MODEL_OPT_5 DDR DDR_1.25G DDR_1.5G AG15
MODEL_OPT_6 CTS GPIO49 LED_PWM0 LED_PWM0
del. EPI_LOCK6 AA7
MODEL_OPT_6 CP BOX Enable Disable RTS GPIO50
MODEL_OPT_7 cause of EPI block deletion AD6
OTP_WRITE GPIO51
MODEL_OPT_8 MODEL_OPT_7 AC8 5V Tolerance
T2 Tuner Support Not Support MODEL_OPT_3 GPIO52
Non_Country_AJJA

AC7 AL16
MODEL_OPT_7 OPCTRL_11_SCL
MTK_NON_DVB_T2_TUNER

MODEL_OPT_9 GPIO53 OPCTRL11

MTK_NON_DVB_S_TUNER

MODEL_OPT_8 S Tuner Support Not Support AB6 AM16

MODEL_OPT_5 GPIO54 OPCTRL10 OPCTRL_10_SDA
NON_Country_TW

MTK_NON_CP_BOX

MODEL_OPT_10 SC_ID_SOC AC6 AE17

MTK_DDR_1.5GB
NON_FRC_60Hz

MODEL_OPT_9 MODEL_OPT_6 GPIO55 OPCTRL9 COMP1_DET

MODULE_V12

DDR DDR_0.78G NON_DDR_0.78G NON_EU AG19

MTK_LARGE

OPCTRL8 SC_DET
MTK_HD

R169
R129
4.7K

10K
R103
4.7K

AJ23 AH17
R104
4.7K

R128
4.7K
R122
4.7K
R107
4.7K

R139
4.7K
R136
4.7K

R143
4.7K

R144
4.7K

R148
4.7K

M13 vs Lean Smart ADIN0_SRV OPCTRL7 OPCTRL7

M13 vs Lean Smart MODEL_OPT_10 EPI OPT R170
Default Option Name change 10K AH23 AE19
Option Name change ADIN1_SRV OPCTRL6 HP_DET
Support to Opt AE28 AH19
Not Support to Deafult ADIN2_SRV OPCTRL5 AV1_CVBS_DET
AD28 AK16
USB_CTL3 MODEL_OPT_0 ADIN3_SRV OPCTRL4 AMP_RESET_SOC
AF22 AG17
M_RFModule_RESET ADIN4_SRV OPCTRL3 OPCTRL3 R182
DDR_1.25G DDR_1.5G DDR_0.768G AK21 AJ17
OPC_EN ADIN5_SRV OPCTRL2 RF_SWITCH_CTL AMP_RESET_SOC AMP_RESET_N
AG24 AF19 33
/TU_RESET1 ADIN6_SRV OPCTRL1 OPCTRL_1_SCL
MODEL_OPT_5 AM18 AJ19 R185
High Low High OPCTRL_0_SDA
MODEL_OPT_4 /S2_RESET ADIN7_SRV OPCTRL0 10K
MODEL_OPT_9
Low Low High

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MID_MAIN_1 2013.07.16
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 508

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 PLACE AT JACK SIDE
Close to JACK Close to Main Chip

C345
+5V_NORMAL 10uF 1608 sizs For EMI 1.0Vpp 1608 sizs For EMI
16V R344
0 R374
COMP1/AV1/DVI_L_IN COMP1/AV1/DVI_L_IN_SOC COMP1_Y/AV1_CVBS COMP1_Y/AV1_CVBS_SOC
R308 30K 1/4W
1.2K R328 3216

ZD302
OPT C388 C394

ADLC 5S 02 015
C338 C342 C384
470K 27pF 27pF R355
560pF 100pF 75 10pF
OPT 50V 50V 50V
50V 50V
OPT OPT 1% R381
R302 10V OPT 0
180 COMP1_COM_SOC
ARC C311 1uF
HDMI_ARC 1/16W
R303
82 R309 C346 1608 sizs For EMI
100K 10uF 0
1608 sizs For EMI COMP1_Pb R373 COMP1_Pb_SOC
16V R345
COMP1/AV1/DVI_R_IN COMP1/AV1/DVI_R_IN_SOC C386 C391
30K R354 C379
27pF 27pF

ZD304
ADLC 5S 02 015
50V 50V 75 10pF
R329 C339 C343
OPT OPT 1% 50V
470K 560pF 100pF
OPT 50V 50V
OPT

1608 sizs For EMI

0 R372
COMP1_Pr COMP1_Pr_SOC

C385 C392 C378

R353
27pF

ZD306
27pF 75 10pF

ADLC 5S 02 015
50V 50V 50V
FOR EMI 1%
OPT OPT

IC105
LGE2122[A2_M13]

IC105 Y1
TXC4N
BE0P
LGE2122[A2_M13] Y2
TXC4P
BE0N
W3
BE1P TXC3N
W4
BE1N TXC3P
V26 AG30 V3
BE2P TXCCLKN
HDMI_CEC TP381 HDMI_CEC HDMI_0_RX_0 V4
AG31 TXCCLKP
HDMI_0_RX_0B BE2N
AC27 AF30 V1
BECKP TXC2N
HDMI_0_SCL HDMI_0_RX_1 V2
AB27 AF31 TXC2P
DDC_SCL_3_JACK HDMI_1_SCL HDMI_0_RX_1B BECKN
AA26 AE32 U3
DDC_SCL_1_SOC BE3P TXC1N
HDMI_2_SCL HDMI_0_RX_2 AA8 U4
W27 AE33 MODEL_OPT_8 TCON0 TXC1P
DDC_SCL_MHL HDMI_3_SCL HDMI_0_RX_2B BE3N
AG32 AA9 T3
MODEL_OPT_9 TCON1 BE4P TXC0N
HDMI_0_RX_C M13 vs Lean Smart W6 T4
AC26 AG33 MODEL_OPT_10 TCON2 TXC0P
HDMI_0_SDA HDMI_0_RX_CB del. list BE4N
AB26 U6
DDC_SDA_3_JACK HDMI_1_SDA (cause of EPI Block deletion) GCLK_SOC TCON3
Y26 AD30 GCLK_SOC U7 AD1
DDC_SDA_1_SOC D0+_HDMI3_JACK MCLK_SOC TCON4 BO0P TXD4N
HDMI_2_SDA HDMI_1_RX_0 MCLK_SOC V8 AD2
W26 AD31 GST_SOC TCON5 TXD4P
DDC_SDA_MHL HDMI_3_SDA HDMI_1_RX_0B D0-_HDMI3_JACK GST_SOC BO0N
AC32 EO_SOC V6 AC3
D1+_HDMI3_JACK EO_SOC TCON6 BO1P TXD3N
HDMI_1_RX_1 VCOM_DYN AB7 AC4
AE29 AC33 VCOM_DYN PMIC_RESET TXD3P
HDMI_0_PWR5V HDMI_1_RX_1B D1-_HDMI3_JACK TCON7 BO1N
R305 Y27 AC30 PMIC_RESET W9 AB3
5V_HDMI_3_JACK 1K TCON8 BO2P TXDCLKN
HDMI_1_PWR5V HDMI_1_RX_2 D2+_HDMI3_JACK U8 AB4
R306 1K AA28 AC31 2D/3D_CTL TXDCLKP
5V_HDMI_1_SOC HDMI_2_PWR5V HDMI_1_RX_2B D2-_HDMI3_JACK TCON9 BO2N
V28 AE30 U9 AB1
5VBUS R307 1K MODEL_OPT_2 TCON10 BOCKP TXD2N
HDMI_3_PWR5V HDMI_1_RX_C CK+_HDMI3_JACK V9 AB2
AE31 PCM_5V_CTL TCON11 TXD2P
HDMI_1_RX_CB CK-_HDMI3_JACK BOCKN
AD29 V7 AA3
USB_CTL2 TCON12 BO3P TXD1N
HDMI_0_HPD AA4
AA27 Y30 +1.2V_MTK_AVDD TXD1P
HDMI_HPD_3_JACK HDMI_1_HPD HDMI_2_RX_0 D0+_HDMI1_SOC BO3N
AA29 Y31 Y3
HDMI_HPD_1_SOC D0-_HDMI1_SOC BO4P TXD0N
HDMI_2_HPD HDMI_2_RX_0B Y4
V29 W32 TXD0P
HDMI_HPD_4_MHL HDMI_3_HPD HDMI_2_RX_1 D1+_HDMI1_SOC BO4N
+1.2V_MTK_AVDD W33 AN1
HDMI_2_RX_1B D1-_HDMI1_SOC AVDD12_LVDS_1
AA33 W30 C350 C354 AN2 AH1
D2+_HDMI1_SOC AVDD12_LVDS_2 AE0P TXA4N
AVDD12_HDMI_0_RX HDMI_2_RX_2 0.1uF 0.1uF VDD3V3 AN3 AH2
AA32 W31 TXA4P
C303 C306 AVDD12_HDMI_1_RX HDMI_2_RX_2B D2-_HDMI1_SOC AVDD12_LVDS_3 AE0N
P33 AA30 AN4 AG3
0.1uF 0.1uF CK+_HDMI1_SOC AVDD33_LVDS AE1P TXA3N
VDD3V3_HDMI AVDD12_HDMI_2_RX HDMI_2_RX_C AG4
P32 AA31 TXA3P
AVDD12_HDMI_3_RX HDMI_2_RX_CB CK-_HDMI1_SOC C347 AE1N
AF3
0.1uF AE2P TXACLKN
AH33 U30 AM4 AF4 CI_ADDR[0-14]
D0+_HDMI4_MHL AVSS12_LVDS_1 AE2N TXACLKP
AVDD33_HDMI HDMI_3_RX_0 AM3 AF1
U31 AVSS12_LVDS_2 TXA2N
HDMI_3_RX_0B D0-_HDMI4_MHL AECKP CI_ADDR[0]
C304 C307 T32 AF5 AF2 TP312
D1+_HDMI4_MHL AVSS12_LVDS_3 AECKN TXA2P CI_ADDR[1]
0.1uF 0.1uF HDMI_3_RX_1 AE3
T33 TXA1N TP313
HDMI_3_RX_1B D1-_HDMI4_MHL AE3P CI_ADDR[2]
T30 AE5 AE4 TP314
D2+_HDMI4_MHL AVSS33_LVDS_1 AE3N TXA1P CI_ADDR[3]
HDMI_3_RX_2 AC5 AD3
AE27 T31 TXA0N TP315
AVSS33_HDMI_RX_1 HDMI_3_RX_2B D2-_HDMI4_MHL AVSS33_LVDS_2 AE4P CI_ADDR[4]
T25 V30 V5 AD4 TP316
CK+_HDMI4_MHL AVSS33_LVDS_3 AE4N TXA0P CI_ADDR[5]
AVSS33_HDMI_RX_2 HDMI_3_RX_C
W25 V31 TP317
AVSS33_HDMI_RX_3 HDMI_3_RX_CB CK-_HDMI4_MHL CI_ADDR[6]
AD27 T1 AM1 TP318
REXT_VPLL AO0P TXB4N CI_ADDR[7]
AVSS33_HDMI_RX_4 AM2
R343 TXB4P TP319
AO0N CI_ADDR[8]
24K AL3 TP320
AO1P TXB3N CI_ADDR[9]
1% AL4 TP321
AO1N TXB3P MT5398_MCLKI CI_ADDR[10]
AK3 TP322
AO2P TXBCLKN MT5398_MIVAL_ERR CI_ADDR[11]
AK4 TP323
AO2N TXBCLKP MT5398_MISTRT CI_ADDR[12]
AK1 TP324
IC105 AOCKP TXB2N CI_ADDR[13]
AK2 TP325
LGE2122[A2_M13] AOCKN TXB2P CI_ADDR[14]
AJ3 TP326
AO3P TXB1N
AJ4 MT5398_TS_OUT[0-7] TP327
AO3N TXB1P For PCB Pattern
AH3 TP328
H32 AL13 AO4P TXB0N
USB_DP3 USB_DP_P0 TXVP_0 EPHY_TDP AH4 HP_OUT TP329
H33 AM13 AO4N TXB0P HP_OUT MT5398_TS_OUT[0]
USB_DM3 USB_DM_P0 TXVN_0 EPHY_TDN For PCB Pattern 1.2K R351 1.2K R369 TP330
HP_ROUT_MAIN MT5398_TS_OUT[1]
1.2K R352 1.2K R370 TP331
J32 AL12 HP_LOUT_MAIN MT5398_TS_OUT[2]
USB_DP2 USB_DP_P1 RXVP_1 EPHY_RDP SC_R_IN_SOC HP_OUT C377 C383 C390 C395 TP332
J31 AM12 HP_OUT MT5398_TS_OUT[3]
1200pF 1200pF 1200pF
USB_DM2 USB_DM_P1 RXVN_1 EPHY_RDN SC_L_IN_SOC IC105 1200pF
MT5398_TS_OUT[4]
TP333
Port was changed !!!! LGE2122[A2_M13] HP_OUT HP_OUT HP_OUT HP_OUT
TP334
K32 AF13 MT5398_TS_OUT[5]
USB_DP1 USB_DP_P2 PHYLED1 MODEL_OPT_1 CI_DATA[0-7] TP335
K31 AJ13 SCART_Rout_SOC MT5398_TS_OUT[6]
WIFI USB_DM1 USB_DM_P2 PHYLED0 /TU_RESET2 TP336
SCART_Lout_SOC MT5398_TS_OUT[7]
0 R382 AL32 AK30 TP337
WIFI_DP AN10 AN12 24K R315 CI_DATA[0]
USB_DP_P3 REXT AIN1_R_AADC AR0_ADAC TP338
0 AM10 AN32 AJ29 CI_DATA[1]
USB_DM_P3 AVDD_33SB AIN1_L_AADC AL0_ADAC TP339
Wake On Lan AM33 CI_DATA[2]
WIFI_DM R383 VDD3V3 PC_R_IN_SOC TP379 AIN2_R_AADC
AM31 AJ31 TP340
WIFI K33 AN14 CI_DATA[3]
AVDD33_USB_P0P1P2 AVDD33_ETH C328 PC_L_IN_SOC TP380 AIN2_L_AADC AR1_ADAC TP341
C398 C399 AN8 AE13 AM32 AK29 CI_DATA[4]
5pF 5pF 0.1uF AIN3_R_AADC AL1_ADAC TP342
AVDD33_USB_P3 AVSS33_ELDO AK33 CI_DATA[5]
50V 50V C302 AIN3_L_AADC TP343
WIFI WIFI 0.1uF M25 AC16 AL33 AJ30 CI_DATA[6]
COMP1/AV1/DVI_R_IN_SOC AIN4_R_AADC AR2_ADAC Ready For commercial Audio_R_OUT TP344
AVSS33_USB_P1 AVSS33_LD AN33 AH28 CI_DATA[7]
AE11 AC15 COMP1/AV1/DVI_L_IN_SOC
AVSS33_USB_P3 AVSS33_COM AIN4_L_AADC AL2_ADAC Ready For commercial Audio_L_OUT TP345
MT5398_TS_IN[0] TP346
MT5398_TS_IN[1] TP347
MT5398_TS_IN[2] TP348
Close to AVDD33_ADAC & AVDD33_AADC AJ33
AVDD33_ADAC MT5398_TS_IN[3]
AC23 TP349
VDD3V3 SPDIF_OUT MT5398_TS_IN[4]
AVSS33_ADAC TP350
AVDD3V3_AADC
L304 AVDD3V3_AADCAJ32 MT5398_TS_IN[5] TP351
ARC
AVDD3V3_AADC AVDD33_AADC MT5398_TS_IN[6] TP352
C365 C305 C362 AC24 AG9
10uF AVSS33_AADC ALIN MT5398_TS_IN[7] TP353
1uF 0.1uF AG10
10V 10V ASPDIF0
TUNER_SIF AN31 V27 SC_ID_SOC TP354
VMID_AADC ASPDIF1 /CI_CD2
AK9 R366 100 TP355
AOBCK AUD_SCK /CI_CD1
Close to MT5369 C352 0.01uF AH25 AJ9 R367 100 TP356
MPXP AOLRCK AUD_LRCK
AF10 R368 100 /PCM_IORD TP357
R339 TU_HK AOMCLK AUD_MASTER_CLK
TU_S/N/Q_T/US/KR/TW AH9 R371 100 /PCM_IOWR TP358
C312 2.2K AUD_LRCH
AOSDATA4
TU_HK C363 AK8 PCM_RST TP307
Close to Tuner C358
1uF
AOSDATA3
AJ8
C387 C389 C393 C396
/PCM_REG
0.1uF Don’t use as GPIO 22pF 22pF 22pF 33pF TP308
33pF AOSDATA2
TU_S/N/Q_T/US/KR/TW

TU_S/N/Q_T/US/KR/TW 10V AH8

R346 OPT OPT OPT OPT /PCM_CE1 TP309
1K AOSDATA1
R334 51 AJ10 MT5398_TS_SYNC TP310
IF_P AOSDATA0
C336 1uF /PCM_WE
TU_S/N/Q_T/US/KR/TW TP311
10V /PCM_OE
R380

TP359
TU_S/N/Q_T/US/KR/TW TU_S/N/Q_T/US/KR/TW
1K

R331 MT5398_TS_VAL TP360

1K C337 1uF R335 51 CI_A_VS1 TP361
IF_N IC105 MT5398_TS_CLK TP362
10V TU_S/N/Q_T/US/KR/TW
TU_S/N/Q_T/US/KR/TW
C310
LGE2122[A2_M13] /PCM_IRQA TP363
/PCM_WAIT TP364
33pF SC_R_IN_SOC TP365
TU_S/N/Q_T/US/KR/TW VDD3V3 AM27 AK18 SC_L_IN_SOC
ADCINP_DEMOD HSYNC TP376 TP366
+1.2V_MTK_AVDD AN27 AL18
ADCINN_DEMOD VSYNC TP305 SC_CVBS_IN_SOC TP367
AL20
C364 RP TP303 SC_COM_SOC TP368
AN26 AM20
C351 0.1uF AVDD33_DEMOD GP TP306 SC_G_SOC TP369
AL19
0.1uF BP TP304 SC_R_SOC TP370
AN28 AN20
AVDD12_DEMOD COM TP382 SC_B_SOC TP371
AK19
SOG TP383 SC_FB_SOC TP372
AL28 AG22
TU_S/N/Q_T/US/KR/TW TU_S/N/Q_T/US/KR/TW AVSS33_DEMOD VGA_SDA TP301 DTV/MNT_V_OUT_SOC TP373
AL27 AH22
R332 10K R342 10K AVSS12_DEMOD VGA_SCL TP302 SCART_Rout_SOC
IF_AGC TP374
HP_OUT C355 SCART_Lout_SOC TP375
Close to Tuner AL21
L303 C341 0.047uF COM1 SC_COM_SOC
BLM18PG121SN1D 0.047uF TU_S/N/Q_T/US/KR/TW AK22
PB1P SC_G_SOC PCM_5V_CTL TP377
TU_S/N/Q_T/US/KR/TW L26 AL22
HP_LOUT_AMP HP_LOUT IF_AGC PR1P SC_R_SOC SC_DET TP378
M28 AM21
Close to MT5369 TP300 RF_AGC Y1P SC_B_SOC
HP_OUT AN21
C332 SOY1 SC_FB_SOC
AJ27 AM23 0.01uF C371 51 R361
0.22uF LOUTN COM0
10V AK27 AL23 0.01uF C372 51 R362 For PCB Pattern
LOUTP PB0P
AL24 0.01uF C373 51 R363
PR0P COMP1_COM_SOC
N27 AN23 0.01uF C374 51 R364
OSCL2 OSCL2 Y0P COMP1_Pb_SOC
N26 AK23 1500pF C375
OSDA2 OSDA2 SOY0 COMP1_Pr_SOC
COMP1_Y/AV1_CVBS_SOC
AH24
VDACX_OUT
AJ24 10 R350
HP_OUT VDACY_OUT DTV/MNT_V_OUT_SOC
SC_CVBS_IN_SOC
L302 EU
VDD3V3
BLM18PG121SN1D AK26 AN25
For PCB Pattern CVBS3P AVDD33_VIDEO
HP_ROUT_AMP HP_ROUT R341 100 C360 0.047uF AM25
COMP1_Y/AV1_CVBS_SOC CVBS2P
HP_OUT R340 100 C359 0.047uF AH26
C331 TU_CVBS CVBS1P
TU_HK TU_HK AK25 AN18
0.22uF CVBS0P AVDD12_RGB
10V C361 1uF AJ26 +1.2V_MTK_AVDD
CVBS_COM
Near the SOC
VDD3V3
AM26 AC19
AVDD33_CVBS AVSS33_VDAC_BG C382
AK17
Place at JACK SIDE AB20
AVSS12_RGB
AVSS33_VDAC
AE20
0.1uF

AVSS33_CVBS_1
AB22
AVSS33_CVBS_2

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS MID_MAIN_2 2013.07.16
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 509

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Renesas MICOM

For Debug For CEC

+3.5V_ST
+3.5V_ST

8pF
8pF
MICOM_DEBUG

R3016 1K
R3014 10K

R3034

C3003
C3002
R3033 LOGO_LIGHT
Don’t remove R3014,

MICOM_DEBUG
MICOM_DEBUG 27K 120K

LOGO_LIGHT
MICOM_RESET
not making float P40

G
P3000
12507WS-04L D3000
X3000
BAT54_SUZHO
1 CEC_REMOTE HDMI_CEC

S
32.768KHz
2
MICOM_DEBUG Q3001 HDMI_WAUP:HDMI_INIT +3.5V_ST
RUE003N02 R3028
3
HDMI_CEC_FET_ROHM 4.7M

G
4
MICOM_RESET OPT
Q3001-*1 MHL_DET
5
SI1012CR-T1-GE3 MHL_DET

10K
D

S
HDMI_CEC_FET_VISHAY

R3032

10K

R3030
GND MICOM_RESET_SW

MICOM_RESET_22OHM
SW3000
JTP-1127WEM

22
2 1

R3031
Ready For C3004

270K
OPT
P124/XT2/EXCLKS
0.1uF

0.47uF
Commercial
+3.5V_ST 16V 4 3

R3029
P122/X2/EXCLK

P41/TI07/TO07
C3001

P137/INTP0

P120/ANI19
P40/TOOL0
ST_BY_DET_CAM ST_BY_DET_CAM

P123/XT1
C3000

P121/X1
0.1uF
MICOM_RESET_33OHM
R3029-*1 33

RESET
+3.5V_ST

REGC
VDD
VSS
R3011 R3021
10K 10K
GP4 High/MID Power SEQUENCE

48
47
46
45
44
43
42
41
40
39
38
37
HDMI_EXT_EDID

P60/SCLA0 1 36 P140/PCLBUZ0/INTP6 RL_ON

I2C_SCL_MICOM
POWER_ON/OFF! P61/SDAA0 2 35 P00/TI00/TXD1
I2C_SDA_MICOM SCART_MUTE SCART_MUTE

EDID_WP EDID_WP
P62 3 34 P01/TO00/RXD1
POWER_ON/OFF2_4 POWER_ON/OFF2_4
P63 4 33 P130
POWER_ON/OFF2_1 PANEL_CTL
P31/TI03/TO03/INTP4 IC3000 P20/ANI0/AVREFP
POWER_ON/OFF2_1

WOL/WIFI_POWER_ON 5 32 KEY2

IR
P75/KR5/INTP9/SCK01/SCL01 6 R5F100GEAFB 31 P21/ANI1/AVREFM
POWER_ON/OFF2_2 KEY1
P74/KR4/INTP8/SI01/SDA01 7 30 P22/ANI2
HDMI_CEC MODEL1_OPT_1
P73/KR3/SO01 MICOM_LEAD_Au P23/ANI3
POWER_ON/OFF2_3 POWER_ON/OFF2_2 8 29 MODEL1_OPT_4

POWER_ON/OFF2_3
P72/KR2/SO21 9 28 P24/ANI4
MODEL1_OPT_0
P71/KR1/SI21/SDA21 10 27 P25/ANI5
EYE_SDA SIDE_HP_MUTE
POWER_ON/OFF2_4
P70/KR0/SCK21/SCL21 11 26 P26/ANI6
EYE_SCL MODEL1_OPT_3
P30/INTP3/RTC1HZ/SCK11/SCL11 12 25 P27/ANI7
CAM_PWR_ON_CMD CAM_PWR_ON_CMD MODEL1_OPT_2
SOC_RESET

13
14
15
16
17
18
19
20
21
22
23
24
EYE_Q
R3035

R3036
EYE_Q
3.3K

3.3K

+3.5V_ST

P50/INTP1/SI11/SDA11
P51/INTP2/SO11
P17/TI02/TO02
P16/TI01/TO01/INTP5
P15/PCLBUZ1/SCK20/SCL20
P14/RXD2/SI20/SDA20
P13/TXD2/SO20
P12/SO00/TXD0/TOOLTXD
P11/SI00/RXD0/TOOLRXD/SDA00
P10/SCK00/SCL00
P146
P147/ANI18
MICOM MODEL OPTION MICOM MODEL OPTION
+3.5V_ST

0 1
MICOM_OLED_MAIN

MICOM_OLED_FRC
R3007-*1

R3007-*2

MODEL_OPT_0 NON LOGO LOGO For LOGO LIGHT

MICOM_NC4.5_5KEY

MICOM_LOGO_LIGHT
MICOM_TOUCH_KEY
10K

10K

10K

10K

10K
10K

56K

22K
MICOM_GED

MICOM_H13

MICOM_PDP

MODEL_OPT_1 TACT_KEY TOUCH_KEY Ready for sample set

R3002

R3003

R3006

R3007

R3013
R3010

MODEL_OPT_2 LCD / OLED PDP Need to Assign ADC port

MODEL_OPT_3 IR_wafer(12/15) IR_wafer(10pin) Ready for sample set

P124/XT2/EXCLKS
P122/X2/EXCLK

P41/TI07/TO07
MODEL_OPT_4 M13 H13

P137/INTP0

P120/ANI19
P40/TOOL0
MODEL1_OPT_0

P123/XT1
P121/X1
MODEL1_OPT_1

RESET
MODEL_OPT_5 NON_GED GED

REGC
VDD
VSS
MODEL1_OPT_2

MODEL1_OPT_3

48
47
46
45
44
43
42
41
40
39
38
37
MODEL1_OPT_4 P60/SCLA0 1 36 P140/PCLBUZ0/INTP6
P61/SDAA0 P00/TI00/TXD1

POWER_DET

SOC_RX

AMP_MUTE

CAM_CTL
2 35
WOL/ETH_POWER_ON

SOC_RESET

INV_CTL

MODEL1_OPT_5
WOL_CTL
POWER_ON/OFF1

SOC_TX
MODEL1_OPT_5

LED_R
P62 3 34 P01/TO00/RXD1
P63 4 33 P130
P31/TI03/TO03/INTP4 IC3000-*1 P20/ANI0/AVREFP
MICOM_NON_LOGO_LIGHT

5 32
P75/KR5/INTP9/SCK01/SCL01 6 R5F100GEAFB#30 31 P21/ANI1/AVREFM
MICOM_NC4_8KEY

MICOM_LCD/OLED

MICOM_TACT_KEY
MICOM_NON_GED

P74/KR4/INTP8/SI01/SDA01 P22/ANI2
10K

10K

10K

10K

10K

10K

7 30
MICOM_M13

P73/KR3/SO01 MICOM_LEAD_Cu P23/ANI3

8 29
P72/KR2/SO21 9 28 P24/ANI4
P71/KR1/SI21/SDA21 P25/ANI5
R3000

R3001

R3004

R3005

R3008

R3012

10 27
P70/KR0/SCK21/SCL21 11 26 P26/ANI6
P30/INTP3/RTC1HZ/SCK11/SCL11 12 25 P27/ANI7
LED_R

CAM_CTL

13
14
15
16
17
18
19
20
21
22
23
24
P50/INTP1/SI11/SDA11
P51/INTP2/SO11
P17/TI02/TO02
P16/TI01/TO01/INTP5
P15/PCLBUZ1/SCK20/SCL20
P14/RXD2/SI20/SDA20
P13/TXD2/SO20
P12/SO00/TXD0/TOOLTXD
P11/SI00/RXD0/TOOLRXD/SDA00
P10/SCK00/SCL00
P146
P147/ANI18
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NetCast4.0 2013.02.05
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MICOM (RENESAS) 530

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 UART FOR DEBUG AV/COMPONENT REAR
R3822
0
COMP1_Y/AV1_CVBS RCA_JACK_PRESS_B/C
+3.3V_NORMAL JK3802-*1
PPJ245-01
OPT
C3800 7E [RD2]E-LUG
RCA_JACK_MOLD_B/C 0.1uF
PPJ245N2-01 R3806
6E [RD2]C-SPRING
JK3802 10K
UART_4PIN_STRAIGHT [GN/YL]E-LUG
6A
R159 4E [RD2]CONTACT
+3.5V_ST P3800
[GN/YL]O-SPRING 1K
12507WS-04L 5A AV1_CVBS_DET
5D [WH]C-SPRING
[GN/YL]CONTACT D3803
4A 5.6V +3.3V_NORMAL [RD1]CONTACT
1 4C
[BL]O-SPRING
5B COMP1_Pb
OPT 6C [RD1]C-SPRING
SOC_RX 2 [RD1]E-LUG-S C3801
7C 0.1uF
8C [RD1]E-LUG-S
[RD1]O-SPRING R3810
3 5C COMP1_Pr 10K
5B [BL]C-SPRING
[RD1]CONTACT
4C R164
SOC_TX 4 4A [GN]CONTACT
1K
[WH]O-SPRING COMP1_DET
5D COMP1/AV1/DVI_L_IN D3800
5 5.6V 6A [GN]C-SPRING

4E D3801
5.6V 7A [GN]E-LUG
[RD2]CONTACT
5E
[RD2]O-SPRING
6E
COMP1/AV1/DVI_R_IN
[RD2]E-LUG

D3802
5.6V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS JACK_COMMON 2011.11.21
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 38

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 Ethernet Block

C5000 C5001
0.1uF 0.01uF
16V 50V

JK5000
RJ45VT-01SN002

1
1
EPHY_TDP

2
2

3
3
EPHY_TDN

4
4
EPHY_RDP

5
5

6
6
EPHY_RDN

7
7
D5000 D5001 D5002 D5003
8 5.5V 5.5V 5.5V 5.5V
8 LAN_ESD LAN_ESD LAN_ESD
LAN_ESD

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS LAN_VERTICAL 2013.11.26
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 550

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 /TU_RESET2_TU /TU_RESET2

FE_DEMOD1_TS_ERROR

1. should be guarded by ground

2. No via on both of them
3. Signal Width >= 12mils
close to Tuner Signal to Signal Width = 12mils
+3.3V_TUNER Ground Width >= 24mils

L6500
BLM18PG121SN1D close to TUNER
1 +3.3V_LNA_TU C6501
0.1uF R6507 1K
Global flag
2 RF_SWITCH_CTL_TU RF_SWITCH_CTL
C6504 R6503
0.1uF 10K

R6506 100
3 IF_AGC_TU IF_AGC
C6502 close to Tuner
0.1uF
16V

R6511 mA(MAX)
4 I2C_SCL6_TU I2C_SCL6
C6505 33
47pF
50V R6512 +3.3V_TUNER
5 I2C_SDA6_TU I2C_SDA6 +3.3V_TUNER 1608 perallel +3.3V_NORMAL
C6503 OPT 33 because of derating
47pF
50V
TU_HK TUNER_SIF TU_HK
OPT TU_HK L6502
R6513 0 R6516 R6517 BLM18PG121SN1D
200 200
6 IF_P IF_P
TU_CVBS C6526 C6529
should be guarded by ground,Match GND VIA 0.1uF 22uF
C6530
E 0.1uF
7 IF_N IF_N 16V 10V 16V
TU_HK 85C
B Q6502
8 TU_SIF_TU MMBT3906(NXP)
C

9 TU_CVBS_TU
+3.3V_TUNER T2 : Max 1.7A
L6501 else : Max 0.7A
10 BLM18PG121SN1D

C6510
0.1uF
11 +3.3V_TU TU_DEMOD_CORE Demod_Core

R6520-*1 R6519-*1 R6521-*1

+3.3V_TUNER IC6500

TU_1.1V
close to Tuner AP2132MP-2.5TRG1 [EP]
12 FE_DEMOD1_TS_ERROR
TU_1.2V

18K
FE_DEMOD1_TS_ERROR TU_DEMOD_CORE R6521
20K
14 FE_DEMOD1_TS_CLK FE_DEMOD1_TS_CLK C6516 1 8 1%
R2

TU_1.1V
0.1uF

THERMAL
PG GND

14K
R6519 TU_1.2V
15

9
FE_DEMOD1_TS_SYNC FE_DEMOD1_TS_SYNC 2 7 11K
1%
TU_DEMOD_CORE
EN ADJ R6520 R1
R6518 10K TU_1.2V
10K

TU_1.1V
FE_DEMOD1_TS_VAL FE_DEMOD1_TS_VAL 3 6 1%
16

2K
VIN VOUT

17 FE_DEMOD1_TS_DATA[0] +5V_NORMAL 4 2A 5
VCTRL NC
TU_DEMOD_CORE
FE_DEMOD1_TS_DATA[1] FE_DEMOD1_TS_DATA[0-7] EAN61387601
18 C6518
10uF
FE_DEMOD1_TS_DATA[0] 16V
19 FE_DEMOD1_TS_DATA[2] FE_DEMOD1_TS_DATA[1] TU_DEMOD_CORE
FE_DEMOD1_TS_DATA[2] C6515
1uF
FE_DEMOD1_TS_DATA[3]
20 FE_DEMOD1_TS_DATA[3]

Global F/E Option Name FE_DEMOD1_TS_DATA[4]

1. TU 21 FE_DEMOD1_TS_DATA[4]

2. Tuner Name = TDS’S’,TDS’Q’...

FE_DEMOD1_TS_DATA[5]
FE_DEMOD1_TS_DATA[6]
Vout=0.6*(1+R1/R2)
3. Country Name = T,T2,S2,KR,US,BR ... 22 FE_DEMOD1_TS_DATA[5] FE_DEMOD1_TS_DATA[7]

Example of Option name FE_DEMOD1_TS_DATA[6]

23
TU_Q_T2 = apply TDSQ type tuner and T2 country
TU_M/W = apply TDSM&TDSW Type Tuner
24 FE_DEMOD1_TS_DATA[7]
13’ Tuner Type for Global R6501 +3.3V_TUNER
100 /TU_RESET1
TDS’S’-G501D : T/C Half NIM Horizontal Type 25 /TU_RESET1_TU
C6507 L6503
TDS’Q’-G501D : T/C/S2 Combo Horizontal type 16V BLM18PG121SN1D
DELETE 1.8V POWER
TDS’Q’-G601D : T2/C/S2 Combo Horizontal Type 0.1uF
26 +3.3V_DEMOD_TU
TDS’Q’-G651D : T2/C/S2 Combo Vertical Type C6511
TDS’Q’-G705D : Singapore DVB-T2 (V1.3.1) 0.1uF
R6510 33
TDS’M’-C601D : China NIM with Isolater Type 27 I2C_SCL4_TU I2C_SCL4
L6505
TDS’W’-J551F : Japan Dual NIM BLM18PG121SN1D
Demod_Core OPT
C6513
TDS’W’-B651F : Brazil 2Tuner 28 D_Demod_Core
18pF
TU_DEMOD_CORE
TDS’W’-A651F : Taiwan 2Tuner C6506 50V
0.1uF OPT R6509 33
TDS’W’-K651F : Colombia DVB-T2 2Tuner 29 LNB_TX LNB_TX I2C_SDA4
TU_DEMOD_CORE C6512
18pF
50V
30 I2C_SDA4_TU

31 LNB_OUT LNB_OUT

34 FE_DEMOD2_TS_ERROR FE_DEMOD2_TS_ERROR

36 FE_DEMOD2_TS_SYNC FE_DEMOD2_TS_SYNC

37 FE_DEMOD2_TS_CLK FE_DEMOD2_TS_CLK

38

1.2V_MHL
39 FE_DEMOD2_TS_VAL FE_DEMOD2_TS_VAL
TU_NO_DEMOD_CORE
+3.3V_NORMAL
IC6515
FE_DEMOD2_TS_DATA FE_DEMOD2_TS_DATA AZ1117BH-1.2TRE1
40
R6502
100 /TU_RESET2 IN OUT
R6515

45 /TU_RESET2_TU C6509 GND/ADJ TU_NO_DEMOD_CORE

16V C6508
1

0.1uF 0.1uF
16V
C6514 C6519
10uF 0.1uF
10V 16V
TU_NO_DEMOD_CORE TU_NO_DEMOD_CORE

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS TUNER_CIRCUIT 2013.07.16
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. 565

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 POWER_ON/OFF1
POWER_ON/OFF2_1
POWER_ON/OFF2_2

14Y SMART TV SMALL Power POWER_ON/OFF2_3

POWER_ON/OFF2_4

DDR MAIN 1.5V PWM_DIM2

20120808 KH.JUNG
POWER_ON/OFF2_1 5V_Normal->POWER_ON/OFF2_1

R2430
10K
C2420

0.1uF
16V C2455
0.1uF
+1.5V_DDR
16V

EP[GND]
+3.3V_NORMAL

VIN_3

PWRGD

BOOT
+3.5V_ST

EN
3.3K -> 1K (threshold voltage up)
R2445 L2411

16

15

14

13
100K R2446 : 36Kohm -> 15Kohm, C2469 Opt by MPS at13.09.05 L2405 VIN_1 PH_3 2.2uH
1 12
THERMAL
VIN_2 2 17 11 PH_2
R8812
+3.5V_ST
C2469 BLM18PG121SN1D NR5040T2R2N
R2446 GND_1 3 10 PH_1
1K
15K
0.1uF
50V
OPT
C2470 +3.5V_ST
C2448
10uF
10V
C2418
10uF
10V
C2419
0.1uF
16V
GND_2
3A 4
IC2403
TPS54319TRE
9 SS/TR C2456
10uF
C2451
10uF
C2454
10uF
C2447
10uF
C2457
0.1uF
16V WLED_ENABLE
+3.3V_NORMAL

8
0.1uF C2450 10V 10V 10V 10V OPT
R8801 +3.5V_ST

AGND

VSENSE

COMP

RT/CLK
16V IC2407 R8808
3.3K 10K
+19V [EP]GND MP1584EN 0.01uF

47K 1%
R8813
R2447

R2455
50V C
R8811 [DV2]

ZD2401
10

6.8K

2.5V
B 10K R8889
L2403 10uH 10K
JK8800 BST SW R2432 OPT
C2452

OPT
8 1 SMAB34 1/16W 330K 5% Q8800 C
R8888
D2402
KJA-DC-1-0032 R1 100pF MMBT3904(NXP)
E
THERMAL

50V B 10K
4 VIN EN 40V C2473C2474
R2431 C2421 INV_CTL
9

4 7 2 C2475 15K 4700pF Q8811

47uF 10uF 5V protect surge for Main IC R8809
25V 0.1uF ZD2403 2014.1.14 MMBT3904(NXP)
E 10K
10V 1/16W 5% 50V
50V OPT
2 2 C2468 FREQ COMP
C8816 6 3
0.1uF C8817 C8820 10uF
300K
R2448

50V 0.1uF 68uF 25V R2433

50V 35V R2457 R2458
1 GND FB 100K 33K 56K R2
1 5 4 1/16W
12.03.08
1/16W 1%
EAE42868301(3225)->
EAE61081701(3216) 1%
1/10W
1% 3A
HDMI LEAKAGE Workaround in MTK A2(A0) (Default= with HDMI_LEAKAGE)
C2471
220pF OPT R2450 Vout=0.827*(1+R1/R2)=1.521V +3.3V_NORMAL
50V C2472 0
150pF OPT
R2456 R2454
50V 39K
R2449 0
1/10W
68K 1%
1/16W 20120813 LCD-TV
20120913 CJLIM 5%
12V_PANEL_VCC +12V

12V_PANEL 5V_PANEL
R2453 R2468
10K 10K
VDD3V3_HDMI
[DV2]

G
S

D
+3.3V_NORMAL NTR4501NT1G
Q2408

C2453
0.1uF
+3.3V_NORMAL
19V->12V(Real Output : 12.3V) +12V L2409
16V

Placed on SMD-TOP

BLM18PG121SN1D OPT L2410

IC2405 2uH
C2430 C2431 C2434
10uF 10uF 0.1uF TPS54327DDAR [EP]GND
16V 16V 16V
EN VIN 16V NR8040T2R0N

R2427
1 8
IC2408 +12V 0.1uF

THERMAL
C2437 C2438 C2439 C2442 C2444 C2445

30K
[EP]

1%
NB634EL VFB VBST 10uF 10uF 10uF 10uF 100pF

9
2 7
10V 10V 10V 10V 50V
OPT
R1
20121010 CJLIM VREG5 SW [DV2]

R2440
L2412 15uH 3 6

3.3K
IN AGND 3225 -> 3216

ZENER_3.3V_NORMAL
1%
1 14 SS GND
4 5
THERMAL

ZD2400
C2476 C2477 C2478 20120726 KH.JUNG
5V_PANEL_VCC

5V
OPT OPT 12V -> 5V
15

4.7uF 4.7uF 0.1uF SW_1 GND_2 OPT POWER_ON/OFF2_2 R2414

50V 50V 50V 2 13 C2488 10K +5V_NORMAL 12V_PANEL_VCC
C2481 C2482 C2483 C2484 C2486 0.1uF +12V
47uF 10uF 10uF 10uF 10uF 50V C2436
PANEL_POWER

R2428
25V 25V 25V 25V 25V 12V_PANEL 5V_PANEL
SW_2 GND_1 0.1uF L2408

10K
1%
3 12 L2401
16V R2 BLM18SG121TN1D BLM18SG121TN1D 12V_PANEL 5V_PANEL
C2480 R2470 R2408
0.1uF 0 C2446 C2487 R2407
SW_3 VCC 50V 1uF 3300pF 0 0
4 11
+5V_NORMAL 10V 50V Q2407
20121101 CJLIM DMP2130L
R2463 C2433
SW_4 AAM 82K

D
5 10 C2432 0.1uF

12V_PANEL
0.01uF

R2442
C2479 50V 50V

33K
0.1uF R2460 R2464
50V 10 BST PG 100K C2440
6 9 12V_PANEL G
1uF
R2461 R2467
Vout=0.765*(1+R1/R2) C2435
4.7uF
25V
EN/SUNC FB 24K 5V_PANEL

R2451

R2452
100K 1% 20131209 for T5 of 22inch

1/8W
10K

1/8W
R2401 7 8 50V C2443

2K

2K
RL_ON_BUFFER
5V_PANEL 5V_PANEL 0.1uF

OPT
12V_PANEL
C2485

OPT
R2466 50V

R2441
100pF R2469

5.6K
6.2K1% 50V R2442-*1 R2441-*1
R2462 0 2.7K
C2401 4.7K 22K
0.1uF 20120816 CJ.LIM
16V R2465 R2461 : 82K -> 24K LCD-TV
C
1K1% R2467 : 12K -> 100K R2437 PANEL_DISCHARGE_REG->OPT
R2466 : 820 -> 6.2K 10K B Q2406
PANEL_CTL
R2465 : 33 -> 1K MMBT3904(NXP)
for phase margin by MPS 130905
E

20120726 KH.JUNG

+1.2V MTK CORE

+5V_Normal +1.2V_MTK_CORE

20120813 LCD-TV

+5V_NORMAL L2404
IC2400 2uH
BD86106EFJ [EP]

IC2404 Add GND JIG Point to bottom side

RT8289GSP [EP]GND
PGND
1 8
SW_2
20120816 CJ.LIM
2014.1.13

R2404
C2423
THERMAL

C2407 C2408 C2409 C2414 C2441

5.1K
0.01uF Placed on SMD-TOP 85C -> 125C 10uF 10uF 10uF 10uF 47pF

1%
VIN SW_1
9

JP8833
JP8830

JP8831

JP8832
L2407 2 7
50V 10V 10V 10V 10V 50V
4.7uH C2405 OPT
BOOT SW AGND EN
BLM18PG121SN1D

1 8 3 6 0.0068uF
L2400

C2400 C2402 C2403 R2402 R1

10uF 10uF 0.1uF 50V
THERMAL

FB COMP 6.8K
16V 16V 16V
D2401
B540C

4 5
NC_1 VIN C2425 C2426 C2429 OPT

ZD2402
C2428
9

40V

0.1uF

2.5V
2 7 22uF 22uF
10uF 16V 20120816 LCD-TV
10V 10V
10V

R2406

OPT
NC_2 GND

10K
1%
3 6
R2403
C2404 10K
POWER_ON/OFF1 R2
FB
4
5A 5
EN
0.1uF
16V
100K
R8890

L2406 20121010 CJLIM

3225 -> 3216

BLM18PG121SN1D C2417 Add Pull Down Resistor POWER_ON/OFF2_3

C2422 for Improving DIP issue
10uF 0.1uF
35V 2013.11.26. R2439
50V
10K
1%
C2427 Vout=0.8*(1+R1/R2)
51K 0.1uF
R2438 R1 16V
R2436
16K

R2
1%

C2424
150pF
50V

Vout=1.222*(1+R1/R2)
20120813 LCD-TV

Power_DET

AO3407A Vgs : 10.8V(24V input) +19V

AMP_VCC Control AO3407A Vgs : 10.36V(19V input)
+3.5V_ST R2416
100K +3.5V_ST

AMP_VCC R2421
OPT R2400 10K
OPT R2412 IC2401
C801 C809 0 OPT
10uF
C839 R880 (AMP_VCC_19v) 8.2K OPT APX803D29
0.1uF 2.2uF 1%
25V 50V 10K +24V
50V Q807 R2418 POWER_DET
12.03.08 DMP2130L S VCC RESET 100
3 2
EAE42868301(3225)->
EAE61081701(3216) G R2411 1
R821 1.8K C2410
12K 1% 0.1uF GND
D 50V
L807 3.3uH
C2412
CPI2520NHL3R3ME 2520
0.1uF
R811 16V
C
R2410

1/10W

0 R810 C860 C865

10K C834
10K

B Q806 10uF 0.01uF

0.01uF
5%

RL_ON_BUFFER MMBT3904(NXP)
50V 25V 50V
E
Improve AMP Power Sequence not to RESET at 8kV ESD
POWER_ON/OFF2_4 R836
R812 10K 2014.1.11.
0
OPT

RL_ON Buffer Circuit

+3.5V_ST
MMBT3906(NXP)
Q2401 RL_ON_BUFFER
R2409
10K 1 3

2
R2405 10K
RL_ON

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS 14Y SMALL 2013.07.25
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. POWER 601

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 14Y SMART TV SMALL HDMI/MHL

CK+_HDMI4_JACK
CK-_HDMI4_JACK
D0+_HDMI4_JACK
D1+_HDMI4_JACK

D0-_HDMI4_JACK
D2+_HDMI4_JACK
D2-_HDMI4_JACK

D1-_HDMI4_JACK
CHANGE NET Demod_Core
1.2V_MHL
Demod_Core
L3302
BLM18PG121SN1D

IP4294CZ10-TBR
IP4294CZ10-TBR
TU_DEMOD_CORE

10
10

9
8
7
6

ESD_HDMI
9
8
7
6
ESD_HDMI

D3302
Close to SIL1292

D3303
HEAT SINK SMD GASKET

1
2
3
4
5
1
2
3
4
5
Field Issue
Latch Up C3316 C3320

R3388
5.1
VDD3V3_HDMI (+3.3V_NORMAL -> VDD3V3)

R3389
0.1uF 0.1uF

5.1
16V 16V
VDD3V3_HDMI
SIL_HPD/CBUS

[EP]GND
VDD33_2

VDD33_1
2013.11.26 delete

RX2+
RX2-
RX1+
RX1-
RX0+
RX0-
RXC+
RXC-
+12V OPT
2N7002K

R3376

R3384 S
Q3304

1K 1.2V_MHL
OPT

SIDE
0

G VDD3V3_HDMI
1.2V_MHL

40
39
38
37
36
35
34
33
32
31
+5V_NORMAL
ADUC 20S 02 010L

5V_MHL
D VDD3V3_HDMI
RSVDL1 1 30 AVDD12 L3301
VDD12_1 TXC- BLM18PG121SN1D
2 29 CK-_HDMI4_MHL
C3311 C3318
R3356 THERMAL
ESD_HDMI

0.1uF 0.1uF
10K RSVDL2 TXC+ 16V 16V
VA3302

SHIELD 3 41 28 CK+_HDMI4_MHL
R3371
ADUC 20S 02 010L

C3321
RESET 4 27 TX0-
820

5VBUS #SIL_RESET 0.1uF

D0-_HDMI4_MHL
16V
GND L3303 +12V C3314 PWR5V_DET 5 IC3304 26 TX0+ D0+_HDMI4_MHL
BLM18PG121SN1D D MHL_DET
R3370 OPT 0.1uF
R3351 INT TX1-
20 1K 16V 6 SIL1292CNUC 25 D1-_HDMI4_MHL
ESD_HDMI

Q3314
VA3303

HP_DET 4.7K OPT

G PMBFJ177
DDC_SDA_MHL
DSDA 7 24 TX1+ D1+_HDMI4_MHL
5V_MHL
19
5V S
DSCL 8 23 TX2-
18 DDC_SCL_MHL D2-_HDMI4_MHL
GND R3348
ADUC 20S 02 010L

CBUS/HPD TX2+
ADUC 20S 02 010L

17 SIL_HPD/CBUS 9 22 D2+_HDMI4_MHL
10K
DDC_DATA R3308 100
VDD5_IN HPD_IN
Change to Angle Type

16
DDC_SDA_MHL 10 21 HDMI_HPD_4_MHL
DDC_CLK R3309 100
Improve EMI(Apply the Mold B/C Model)
5V_MHL

11
12
13
14
15
16
17
18
19
20
15 DDC_SCL_4_JACK R3358
ESD_HDMI

NC
VA3301

ESD_HDMI
VA3300

4.7K 5V_MHL
14 OPT
CE_REMOTE

RSVDNC
VREG33_OUT
PS_CTRL
HDMI_DET
GPIO1/CI2CA
GPIO0
CSDA
CSCL
CEC_A
VDD12_2
CEC_REMOTE C3313
13
CK- 0.1uF 1.2V_MHL R3362
CK-_HDMI4_JACK 16V 10K
12
CK_GND
EAG59023302

11
CK+ HDMI_DET
10 CK+_HDMI4_JACK
D0- VDD3V3_HDMI
9 D0-_HDMI4_JACK R3357 C
D0_GND +3.5V_ST 10K Q3310
8 OPT B
R3355 MMBT3904(NXP)
D0+ MHL_DET

R3363 10K
7 D0+_HDMI4_JACK E
R3374

4.7K
D1- OPT
10K

6 R3345
D1-_HDMI4_JACK
D1_GND
Delete Multi Item (Angle Type)
5 R3375 E MMBT3906(NXP) 4.7K
10K Q3302
D1+
4 D1+_HDMI4_JACK B
D2-
3 D2-_HDMI4_JACK C C
R3373
D2_GND 1K
2 B
MHL_DET #MHL_OCP TP3300

I2C_SDA4

I2C_SCL4
D2+ 1/16W Q3301
R3386

HDMI_DET
1
180K

D2+_HDMI4_JACK 5% C3322 MMBT3904(NXP) E

0.1uF (CD_SENCE) Current Limit
16V 5VBUS
OPT
R3387

IC3301 5V_MHL
120K

YKF45-7058V TPS2051BDBVR

JK3301
D3322 OUT IN
1 5
+3.5V_ST 5V_MHL 30V
ZD501 C3315
C3312
UI : HDMI3 --> HDMI2 10uF
R3359 GND
2
5V
OPT
0.1uF
16V
10V 100K
5V_MHL

A1

A2
OC EN

MMBD6100
3 4 MHL_DET

D3301

R3332
10K
C
5V_HDMI_1_SOC R3338 #MHL_OCP
5V_HDMI_3_JACK 10K
R3361
47K
SIDE SIDE DDC_SCL_MHL
VA3304 30V
ESD_HDMI ADUC 20S 02 010L DDC_SCL_4_JACK
BAT54_SUZHO
D3304
ADUC 20S 02 010L

R3330 R3336 5V_MHL

1K 4.7K
GND
SHIELD Q3309
HDMI_INTERNAL_EDID
PMV48XP
C R3331
20 HDMI_HPD_1_SOC

D
VA3305

Q3303 B 1K
HP_DET HDMI_HPD_3_JACK
MMBT3904(NXP)
19

30V

BAT54_SUZHO
D3312
30V

BAT54_SUZHO
D3313
R3379
5V R3327
E R3321

22K
100K G
ESD_HDMI

ADUC 20S 02 010L

ADUC 20S 02 010L

18 4.7K
GND
HDMI_EXT_EDID
Delete HDMI2
ADUC 20S 02 010L

17 DDC_SDA_1_SOC
DDC_DATA R3328 100
DDC_SDA_3_JACK
16
DDC_CLK R3329 100 DDC_SCL_1_SOC C
R3381 R3380 R3307
Change to Angle Type

DDC_SCL_3_JACK
VA3306

VA3307

15 22K B Q3311 1.8K 1.8K

ARC
HDMI_ARC
MHL_DET MMBT3904(NXP)
VA3313

14
CE_REMOTE
ESD_HDMI

E DDC_SDA_MHL
CEC_REMOTE
ESD_HDMI

ESD_HDMI

13
CK- ESD_HDMI DDC_SCL_MHL
12 D3320
CK_GND IP4294CZ10-TBR CK-_HDMI1_SOC
EAG59023302

11 1 10 CK+_HDMI1_SOC
CK+
10 CK-_HDMI3_JACK
2 9
D0- CK+_HDMI3_JACK
9 3 8 D0-_HDMI1_SOC +5V_NORMAL
D0_GND 4 7 D0+_HDMI1_SOC
8 D0-_HDMI3_JACK
5 6 CEC_REMOTE
D0+_HDMI3_JACK

A1

A2
D0+

MMBD6100
7

D3314
ESD_HDMI
D1- D3321
6
ESD_HDMI
ADUC 20S 02 010L
VA3312

IP4294CZ10-TBR 5V_HDMI_1_SOC +5V_NORMAL

C
D1_GND HDMI_EXT_EDID
5 1 10 E
D1+ D1-_HDMI3_JACK
4 2 9 D1-_HDMI1_SOC MMBT3904(NXP)
D1+_HDMI3_JACK EDID_WP

HDMI_EXT_EDID
D2- 3 8 D1+_HDMI1_SOC Q3313 B
3

A1

A2

HDMI_INTERNAL_EDID

HDMI_INTERNAL_EDID
4 7 C
D2-_HDMI3_JACK

R3337

R3339
D2_GND 5 6 IC3300 MMBD6100 C3302
2 D2-_HDMI1_SOC 0.1uF R3340

47K
D2+_HDMI3_JACK

47K
M24C02-RMN6T D3300 16V 47K
D2+ D2+_HDMI1_SOC Del. DDC_SCL_1_DDC

C
1 DDC_SDA_1_DDC
Pull up Resistors
HDMI_EXT_EDID

E0 VCC
1 8
R3390

HDMI_EXT_EDID

HDMI_EXT_EDID
10K

JK3303
E1 WC
YKF45-7058V 2 7 R3323 R3325
47K 47K
R3319
UI : HDMI1 UI : HDMI2 E2
3
HDMI_EXT_EDID
6
SCL 22 DDC_SDA_MHL
DDC_SCL_3_JACK
HDMI_EXT_EDID
R3320
VSS SDA 22
4 5 DDC_SDA_3_JACK
HDMI_EXT_EDID

Change from DDC1 to DDC3

DDC_SCL_3_JACK

DDC_SDA_3_JACK

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS 14Y SMART TV SMALL 2013.07.25
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. HDMI/MHL 602

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 14Y SMART TV SMALL IR&JOG/WIFI

+3.5V_ST_WAKE
+3.5V_ST L4111
BLM18PG121SN1D
MAX 0.4A
WIFI

R4117
10K
R4118
10K
IR & JOG WIFI 120-ohm L4112
BLM18PG121SN1D
+3.3V_NORMAL

5% 5%
C4113 C4112 OPT C4110
C4111 0.1uF
R4113 10uF 10uF 0.1uF
100 P4101
P4102 16V
10V 10V 16V
KEY1
12507WR-08L
12507WR-10L WIFI WIFI WIFI OPT
R4114 D4101
100 5.6V
KEY2 For EMI
AMOTECH CO., LTD. GND
C4100 C4102 OPT 1
0.1uF 0.1uF
D4100
5.6V KEY1
AMOTECH CO., LTD. 2 WIFI
+3.5V_ST P4100
OPT
12507WR-06L OPT
KEY2 0
3

Change to 6 Pin wafer

L4100 R4109
BLM18PG121SN1D +3.5V_ST 1 Need impedance matching M_REMOTE_RX
4 M104 at WIFI_DM/DP Line

WIFI_FILTER

MDS62110213
GND 2 WIFI_DM M_REMOTE_TX
C4104 R4125 10K 5
1000pF LED_R WIFI_FILTER 3 2
50V LED_R
Place Near Micom ACM2012-900H-2P
LOGO/LED_R 3 WIFI_DP M_RFModule_RESET
+3.5V_ST 6
4 L4103 1
IR 4 CTS
7 WIFI_FILTER
0 OPT
0
R4131 GND 5 R4108 RTS
10K

8
R4133

R4110
OPT

22 NON_EYE_Q_8P
LOGO_LIGHT R4137

MPZ2012S300A
100 9 6
EYE_SCL 9
C
LOGO_LIGHT WIFI

L4104
EYE_Q_10P D4105 WIFI
B 7 5.5V
LOGO_LIGHT ADMC 5M 02 200L Ready 13Y MTV EMI Solution 5.5V
10 D4102
LOGO_LIGHT

1K Q4100 D4103
LOGO_LIGHT

R4138 OPT
R4134 EYE_Q_10P
R4132

MMBT3904(NXP)E 100
C4120 LOGO_LIGHT EYE_SDA 11
10K

0.1uF
16V EYE_Q_10P D4106
ADMC 5M 02 200L
OPT
+3.5V_ST

R4107
OPT
10K
WOL/ETH_POWER_ON
22
IR R4130

D4104 WIFI
C4107 OPT
100pF 5.6V WOL/WIFI_POWER_ON
50V AMOTECH CO., LTD.
22
R4136

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS 14Y SMART TV SMALL 2013.07.25.
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. IR&JOG / WIFI 606

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 14Y SMART TV SMALL USB
USB_CTL3

USB_DM3

USB_DP3

/USB_OCD3

+3.3V_NORMAL

OCP USB2 +5V_USB_2

USB2
R4304
10K
OPT
R4303
10K
MAX 1.5A
3AU04S-305-ZC-(LG)
IC4301 JK4302
AP2171DM8G +5V_USB_2

1
+5V_NORMAL

USB DOWN STREAM

GND NC R4305
1 8 2.2

2
USB_DM2
IN_1 OUT_2 R4306
2 7 2.2

3
USB_DP2
C4302 C4301 Add Serial Resistor
0.1uF IN_2 OUT_1
3 6 10uF C4322 for EOS improvement
16V 2013.11.26

4
10V 10uF
EN FLG 10V

5
4 5
/USB_OCD2

USB_CTL2

+3.3V_NORMAL

OCP USB1 +5V_USB_1 USB1 (DVR Ready)

R4302
10K
OPT
R4301
10K MAX 1.5A
3AU04S-305-ZC-(LG)
IC4300 JK4300
AP2171DM8G +5V_USB_1

1
+5V_NORMAL

USB DOWN STREAM

GND NC R4307
1 8 2.2

2
USB_DM1
IN_1 OUT_2 R4308
2 7 2.2

3
USB_DP1
C4304 C4303
0.1uF IN_2 OUT_1 Add Serial Resistor
3 6 10uF
16V C4310 for EOS improvement

4
10V 2013.11.26
10uF
EN FLG

5
4 5 10V
/USB_OCD1

USB_CTL1

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
14Y SMART TV SAMLL 2013.07.25
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR USB1/2 600
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 14Y SMART TV SMALL LVDS INTERFACE

LVDS_FHD LVDS_HD 2D/3D_CTL 2D/3D_CTL

I2C_SDA1

[30Pin FHD 60Hz] [30Pin HD 60Hz] I2C_SCL1

PWM_DIM1

OPC_EN

TXA0N TXC0N
5V_PANEL_VCC
TXA0P TXC0P

5V_PANEL TXA1N TXC1N

5V_PANEL
L1102 P7103 TXA1P TXC1P
12V_PANEL
120OHM 10031HR-30
UBW2012-121F P7102 TXA2N TXC2N
T-CON
Pin T-CON 10031HR-30
Assign Pin TXA2P TXC2P
Assign
1 30 5V
GND 30 1
2 29 TXACLKN TXCCLKN
5V
5V_PANEL

5V_PANEL

5V_PANEL NC 29 2
3 TXACLKP TXCCLKP
4.7K
R1113

4.7K
R1114

C1102 28 5V
0.1uF NC 28 3
4 27 Interlace Mode Selection
16V
NC 27 4
5 26 TXA3N TXC3N
NC
GND 26 5
6 25 TXA3P TXC3P
NC
RD+ 25 6 TXA0N
7 24 TXA4N TXC4N
GND
RD- 24 7 TXA0P
TXA0N 8 23 TXA4P TXC4P
SR3+
GND 23 8
TXA0P 9 22 SR3-
RCL+ 22 9 TXA1N
TXA1N 10 21 SCLK+
RCLK- 21 10 TXA1P
TXA1P 11 20 TXB0N TXD0N
SCLK-
GND 20 11
TXA2N 12 19 TXB0P TXD0P
SR2+
RC+ 19 12 TXA2N
TXA2P 13 18 TXB1N TXD1N
SR2-
RC- 18 13 TXA2P
14 17 TXB1P TXD1P
GND
GND 17 14
TXACLKN 15 16 TXB2N TXD2N
SR1+
RB+ 16 15 TXACLKN
TXACLKP 16 15 TXB2P TXD2P
SR1-
RB- 15 16 TXACLKP
17 14 GND
GND 14 17
TXA3N 18 13 TXBCLKN TXDCLKN
SR0+ LVDS_SEL
RA+ 13 18 TXA3N
TXA3P 19 12 TXBCLKP TXDCLKP
SR0- +3.3V_NORMAL
RA- 12 19 TXA3P
TXB0N 20 11 FR3+
GND 11 20
TXB0P 21 10 LVDS_VESA TXB3N TXD3N
FR3-
Flicker Tuning Protection 10 21 R1109
TXB1N 22 9 3.3K for 22" HD module TXB3P TXD3P
FCLK+
LVDS SEL 9 22
23 5V_PANEL_VCC TXB4N TXD4N
TXB1P 8 FCLK- 12V_PANEL_VCC
8 23 LVDS_JEIDA
24 GND R1110 TXB4P TXD4P
7 GND 10K
GND 7 24 12V_PANEL OPT
TXB2N 25 6 L1101
FR2+ L1103
GND 6 25 120OHM 120OHM
TXB2P 26 5 UBW2012-121F
FR2- UBW2012-121F
GND 5 26
TXBCLKN 27 4 FR1+
VLCD 4 27
TXBCLKP 28 3 FR1-
VLCD 3 28
29 4.7K 4.7K 12V_PANEL
TXB3N 2 FR0+
2 29 R1112 R1111 C1101
30 VLCD 0.1uF
TXB3P 1 FR0- 12V_PANEL 12V_PANEL
1 30 16V
VLCD
31
31

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS 14Y SMART TV SMALL 2013.07.25
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LVDS 603

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 LOCAL DIMMING Delete

L/DIM0_SCLK

L/DIM0_MOSI

I2C_SCL1

I2C_SDA1

L/DIM0_VS

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS 14Y SMART TV SMALL 2013.07.25.
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LOCAL DIMMING 604

Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
 14Y SMART TV LED DRIVER +19V
13.10.17
28" Diode Iuput Current 2.27A
11.12.02 change to 3A Diode
22uF 2EA->47uF 1EA L65000 D65000
11.11.15 EAE60365101->EAE61423901
1K->100ohm 33uH UF3D(SUZHOU GRANDE)
1000pF->100pF
R65006
100
WLED_ENABLE C65003 C65004
47uF 4.7uF
R65010 C65002 25V 50V 11.11.29
100K 100pF 0DSKE00048A Diode DEL
1% 50V

IC65000
DT1641AS [EP]GND
12.08.11 D
270K+270K
->510K 2012size Q65000
EN VIN R65024 0 G AOD478
C65005
1 24 1uF
Vout(ovp)= Vovp_ref(3V) x [Rovpl+Rovph]/Rovpl Rovph S

THERMAL
= 3V x (510K+22K)/22K = 72.54V 25V
R65003

25
510K OVP VREF
VOUT 2 23
1/8W Rovpl Over Current Limit
1% R65009 C65001 300mA/Rcs(100mohm)=3A
R65000 NC_1 CS
22K 1000pF 3 22
100
PWM_DIM1 1% 50V
R65025
PGND_1 NDRV
4 21 0.1 Rcs
R65001 C65000
100K 100pF 12.08.11
Rss
1%
50V 24K->22K PGND_2 RSS R65018 1W
5 20 R65016 RSS : Setting Soft Start Time
11.11.15 220K 1% 30K 1% Ccp2
1000pF->100pF C65007 SST[s] = (Ccp1 x V)/2(1.25/Rss)
PDIM COMP
6 19 V = Vcomp_stable - Vcomp_charge_start
when using ADIM function, connect PWM_DIM2 OPT 4700pF
R65002 50V
100K RISET RT R65015 R65017 C65009
7 18 R65019
PWM_DIM2 RT : Setting Operation Freq.
1% 39K 1% 1.5K 1%
R65004 1.5K 1% 0.047uF
LS8 LS1 25V
1K 8 17 Ccp1
Riset[ohm] = 1240[v] / Iled[A] 1%
Iled[A] = 1240[v] / Riset[ohm] Riset R65005
18K LS7 LS2
28inch 1string 130mA / 2ch = 65mA/ch 9 16
1%
22inch 1string 130mA / 2ch = 65mA/ch
LS6 LS3
65mA = 1240[V] / 19[Kohm] 10 15

LS5 LS4
11 14

NC_2 LGND
12 13

12.10.16
EAN62407801->EAN62656301

VOUT 2013.10.07. DMB Tech. Recommend circuit

discharge path & Current ripple reducting
13.10.17. Improve Ripple Current

LED_28inch OPT OPT

C65013 C65011 C65012
1uF 1/10W C65006 C65015 C65008 1uF
100V 100K 33uF 33uF 1uF 1uF
R65030 100V 100V 100V 100V 100V

C65014 1/10W
1uF 100K
100V
R65031

R65011 0

1/10W 2013.10.30. 28" LED Pinmap is changed

R65012 0 LED_22inch P65000
R65027 0 22Inch 28Inch
1/10W
12507WR-06L
LED_22inch 1/10W
R65007 0 R65013 0 LED_28inch
JP65001
1/10W
LED_22inch 1/10W 1 FB2 FB1
R65008 0 R65014 0 LED_28inch

1/10W JP65000
1/10W 2 FB3
FB2

3
VLED VLED
JP65002
4
VLED VLED
JP65004
5 NC
FB1

OPT 6
FB1 FB2
R65028 0 R65023 0
JP65003

1/10W 1/10W LED_22inch 7

OPT R65026 0
R65029 0 R65020 0
1/10W
1/10W 1/10W IF130mA IF130mA
R65021 0

1/10W 2 String 3 String

16 PKG 18 PKG
R65022 0

1/10W
THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION. 2013.07.25.
14Y SMART TV SMALL
FIRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS
ESSENTIAL THAT ONLY MANUFACTURES SPECIFIED PARTS BE USED FOR LED DRIVER 605
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
Copyright © 2015 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
Repair guide
 Contents of LCD TV Standard Repair Process

No. Error symptom (High category) Error symptom (Mid category) Page Remarks

1 No video/Normal audio 1

2 No video/No audio 2

3 A. Video error Video error, video lag/stop, fail tunning 3, 4

4 Color error 5

Vertical/Horizontal bar, residual image, light

5 6
spot, external device color error
6 No power 7
B. Power error Off when on, off while viewing, power auto
7 8
on/off
8 No audio/Normal video 9
C. Audio error
9 Wrecked audio/discontinuation/noise 10
No response in remote controller, key error,
10 11
D. Function error recording error, memory error
11 External device recognition error 12

12 E. Noise Circuit noise, mechanical noise 13

13 F. Exterior error Exterior defect 14

14 G. Network error Connection defect / Network speed low 15

First of all, Check whether there is SVC Bulletin in GCSC System for these model.
 Contents of LCD TV Standard Repair Process Detail Technical Manual
No. Error symptom Content Page Remarks
1 Check LCD back light with naked eye A1
2 LED driver measuring method A2
A. Video error_ No video/Normal audio
3 Check White Balance value A3
4 Main Board voltage measuring method A4
6 TUNER input signal strength checking method A6
A. Video error_ No video/Video lag/stop
7 LCD-TV Version checking method A7
9 LCD TV connection diagram A8
10 Tuner Checking Part A9
A. Video error_Color error Check Link Cable (LVDS) reconnection
11 A10
condition
12 Adjustment Test pattern - ADJ Key A12
13 LCD TV connection diagram A8
A. Video error_Vertical/Horizontal bar, Check Link Cable (LVDS) reconnection
14 A10
residual image, light spot condition
15 Adjustment Test pattern - ADJ Key A12
16 Exchange T-Con Board (1) A-1/5

17 Exchange T-Con Board (2) A-2/5

<Appendix>
18 Defected Type caused by T-Con/ Exchange LED driver Board (PSU) A-3/5
Inverter/ Module
19 Exchange Module itself (1) A-4/5
20 Exchange Module itself (2) A-5/5
Standard Repair Process
Established
Error A. Video error date
LCD TV symptom
No video/ Normal audio Revised date

First of all, Check whether all of cables between board is inserted properly or not.
(Main B/D↔ Power B/D, LVDS Cable,Speaker Cable,IR B/D Cable,,,)

☞A1 ☞A4
No video Normal Y Check Back Light Y Check MAIN Board Normal Y
Normal audio On Replace Module
audio On with naked eye Voltage19V voltage

N N N
Move to No ☞A2 Check LED Driver Replace MAIN B/D
video/No audio

Normal Y Replace module

voltage

End
N

Replace MAIN B/D

※Precaution ☞A7 & A3

Always check & record S/W Version and White
Replace Main Board Re-enter White Balance value
Balance value before replacing the Main Board
Standard Repair Process

Established
Error A. Video error date
LCD TV symptom
No video/ No audio Revised date

☞A4
Y Check and
No Video/ Check MAIN Board Normal
replace
No audio Voltage 19V voltage?
MAIN B/D

N End

Replace Adaptor
Standard Repair Process

Established
Error A. Picture Problem date
LCD TV symptom
Picture broken/ Freezing Revised date

. By using Digital signal level meter

☞ A6
. By using Diagnostics menu on OSD
Check RF Signal level ( Menu→ Set up→ Support → Signal Test )
- Signal strength (Normal : over 50%)
- Signal Quality (Normal: over 50%)

Y Check whether other equipments have problem or not.

Normal
(By connecting RF Cable at other equipment)
Signal?
→ DVD Player ,Set-Top-Box, Different maker TV etc`

N
☞ A7
Check RF Cable
Normal Y Check SVC N Use Signal Test Normal Y
Connection Close
1. Reconnection Picture? S/W Version Bulletin? Check Signal status Picture?
2. Install Booster
Y N
N
S/W Upgrade Check
N Contact with signal distributor
Normal Tuner soldering
Picture? or broadcaster (Cable or Air)
Normal N
Y Picture? Replace
Main B/D
Y
Close
Close
Standard Repair Process

Established
Error A. Picture Problem (DVB-S/S2) date
LCD TV symptom
Tuning fail, Picture broken/ Freezing Revised date

☞ A6 Check RF signal cable (DVB satellite signal or not)

Check whether other equipments have problem or not.
Check RF Signal level
(By connecting RF Cable at other equipment)
→ Set-Top-Box, Different maker TV etc

Check satellite setting. ☞ A7

- Check LNB frequency. Y N
Normal Y Normal Check SVC Check Replace
- Check satellite
Signal? setting? S/W Version Bulletin? Tuner soldering Main B/D
- Check Satellite connection
(DiSEqC, motor, etc…) Y
N N
S/W Upgrade

Contact with
Change satellite setting N
signal distributor Normal
(match with installed ANT)
or broadcaster Picture?
(Cable or Air)
Y
N
Normal
Picture? Close
Close
Y

Close
Standard Repair Process

Established
Error A. Video error date
LCD TV symptom
Color error Revised date

☞A8
☞ A10/ A11
※ Check and Y
Check color by input
replace Link
-External Input Y Y
Color Cable Color Color
-COMPONENT Replace Main B/D Replace module
error? (LVDS) and error? error?
-RGB
contact
-HDMI/DVI N N N
condition

Check error color End

input mode

☞A12 Check
External Input/ External Y
external
Check Test pattern Component device/Cable Replace Main B/D
device and
error normal
cable
N

Request repair
for external
device/cable

RGB/ Check external External Y

HDMI/DVI device and device/Cable Replace Main B/D
error cable normal
Standard Repair Process

A. Video error Established

Error date
LCD TV symptom Vertical / Horizontal bar, residual image,
light spot, external device color error Revised date

Vertical/Horizontal bar, residual image, light spot Replace

Module
☞A8
☞ A10/ A11 N
Check color condition by input Check external
Check and
-External Input Screen Y device Y Screen N Replace Main B/D Screen
-Component Normal? replace Link
normal? connection normal? normal?
-RGB Cable
condition
-HDMI/DVI
N N Y
Y

Replace Request repair End End

for external
☞A12 module
device
Check Test pattern

External device screen error-Color error

Check screen
condition by input
Check S/W Version Check N External
-External Input Connect other external
version Input N
-Component
error device and cable Screen Replace
-RGB
(Check normal operation of normal? Main B/D
-HDMI/DVI
Y External Input, Component,
Component RGB and HDMI/DVI by
error Y
S/W Upgrade connecting Jig, pattern
Generator ,Set-top Box etc.
Request repair for
external device
RGB
Y
error Connect other external
Normal N
device and cable N
screen? (Check normal operation of Screen Replace
External Input, Component, normal? Main B/D
Y HDMI/ RGB and HDMI/DVI by
DVI connecting Jig, pattern
Generator ,Set-top Box etc.
End
Standard Repair Process

Established
Error B. Power error date
LCD TV symptom
No power Revised date

☞A17 ☞A18
Check Power LED Y
Check Power input voltage and ST-BY 3.5V Replace Main B/D
Power LED On?

. Stand-By: Red N
. Operating: white
Check Power cord
was inserted properly

N
Normal?

Y
Y
※
Close Check MAIN B/D Normal
Voltage 19V Y
voltage?

☞A4
N

Measure voltage of each output of Power B/D Replace Adaptor

Standard Repair Process

Established
Error B. Power error date
LCD TV symptom
Off when on, off while viewing, power auto on/off Revised date

☞A22
N
Check A/C cord Error? Check Power Off CPU End
Replace Main B/D
Mode Abnormal

Y Abnormal
1

Fix A/C cord & Adaptor

* Please refer to the all cases which Status Power off List Explanation
"POWEROFF_REMOTEKEY" Power off by REMOTE CONTROL
can be displayed on power off mode.
"POWEROFF_OFFTIMER" Power off by OFF TIMER
"POWEROFF_SLEEPTIMER" Power off by SLEEP TIMER
"POWEROFF_INSTOP" Power off by INSTOP KEY
"POWEROFF_AUTOOFF" Power off by AUTO OFF
Normal "POWEROFF_ONTIMER" Power off by ON TIMER
"POWEROFF_RS232C" Power off by RS232C
"POWEROFF_RESREC" Power off by Reservated Record
"POWEROFF_RECEND" Power off by End of Recording
"POWEROFF_SWDOWN" Power off by S/W Download
"POWEROFF_UNKNOWN" Power off by unknown status except listed case
"POWEROFF_ABNORMAL1" Power off by abnormal status except CPU trouble
Abnormal
"POWEROFF_CPUABNORMAL" Power off by CPU Abnormal
Standard Repair Process

Established
Error C. Audio error date
LCD TV symptom
No audio/ Normal video Revised date

☞A24 ☞A25
Check user N Check audio B+ 19V Y
No audio Normal
menu > Off of MAIN Board
Screen normal voltage
Speaker off
Y N

Cancel OFF Replace MAIN board

Check Speaker N
Disconnection Replace MAIN Board End
disconnection

Replace Speaker
Standard Repair Process

Established
Error C. Audio error date
LCD TV symptom
Wrecked audio/ discontinuation/noise Revised date

→ abnormal audio/discontinuation/noise is same after “Check input signal” compared to No audio

☞A25
Wrecked audio/
Check and replace
Discontinuation/ Check audio
speaker and
Noise for B+ Voltage (19V)
connector
Check input all audio
signal Y Y
Signal
-RF
normal? Wrecked audio/
-External Input Normal
signal Discontinuation/
N Replace Main B/D voltage?
Noise only
for D-TV
N
Wrecked audio/
Discontinuation/
Replace MAIN B/D
Noise only
for Analog
(When RF signal is not
received)
Request repair to external Wrecked audio/ Replace MAIN B/D End
cable/ANT provider Discontinuation/
Noise only
(In case of External for External Input
N
Input signal error) Connect and check Normal
Check and fix other external device audio?
external device
Y

Check and fix external device

Standard Repair Process

D. General Function Problem Established

Error date
LCD TV symptom
Remote control & Local switch checking Revised date

1. Remote control(R/C) operating error Replace

Main B/D
☞A27 ☞A27 ☞A27
Check & Repair N Y Y
Check R/C itself Normal Y Normal Check B+ 3.5V Normal Check IR Normal
operating? Cable connection operating? Voltage? Signal?
Operation On Main B/D Output signal
Connector solder
N
Y N N
☞A4
Check R/C Operating Check & Replace Close Check 19v on MAIN B/D Repair/Replace
When turn off light Baterry of R/C Replace Adaptor IR B/D
in room Replace Main B/D
(Adaptor don’t have problem)
If R/C operate, Normal
operating? Close
Explain the customer
cause is interference
from light in room. N

Replace R/C
Standard Repair Process

Established
Error D. Function error date
LCD TV symptom
External device recognition error Revised date

Y Check technical
Check External Input and
Signal information Technical N
input Component Replace Main B/D
input? - Fix information information?
Recognition error
signal
- S/W Version
N Y

RGB,HDMI/
Check and fix DVI, Optical
Fix in Replace Main B/D
external device/cable Recognition error
accordance
with technical
information
Standard Repair Process

Established
Error E. Noise date
LCD TV symptom
Circuit noise, mechanical noise Revised date

Replace PSU(with LED driver)

Check location
Identify Circuit OR
of noise
noise type noise
Replace LED driver

Mechanical Check location of

noise noise

※ When the nose is severe, replace the module

(For models with fix information, upgrade the S/W or
※ Mechanical noise is a natural provide the description)
phenomenon, and apply the 1st level
description. When the customer does not OR ※ If there is a “Tak Tak” noise from the cabinet,
agree, apply the process by stage. refer to the KMS fix information and then proceed
※ Describe the basis of the description in as shown in the solution manual
“Part related to nose” in the Owner’s Manual. (For models without any fix information, provide
the description)
Standard Repair Process

Established
Error F. Exterior defect date
LCD TV symptom
Exterior defect Revised date

Zoom part with Module

Replace module
exterior damage damage

Cabinet
Replace cabinet
damage

Remote
controller Replace remote controller
damage

Stand
Replace stand
dent
Standard Repair Process

Established
Error G. Network Error date
LCD TV symptom
Exterior defect Revised date

Check Wired ethernet cable connection

Check Network status Check whether AP has a probelm or not.
Setting  Network  Networ Status

Check Network connection ☞ A7

Case1 WiFi . Y N
Normal Y Normal Check SVC Check Replace
- Check AP status
Signal? setting? S/W Version Bulletin? Wired, Wifi status Main B/D
Case2 Wired
(Cable / sub Assy)
- Check ethernet Port Y
N N
S/W Upgrade

Check connection
Try to new network connection N
with AP or internet Normal
(match with AP and ether setting)
(WiFi = AP) Picture?
(Wired = ethernet
port)
Y
N
Normal
Picture? Close
Close
Y

Close
Standard Repair Process

Established
Error G. CI+ Competibility Error date
LCD TV symptom
Exterior defect Revised date

Check defect CI slot pin

Check CI CAM status Check it’s worked CI+ 1.2 or 1.3
Setting  Antenna  CI information

Read Y Check status of CI+ Key in the Is there Y Check SVC N Check Replace
Information? In-start menu CI+ key? CAM S/W Bulletin? Wired, Wifi status Main B/D
Version (Cable / sub Assy)
N N Y

CAM S/W Upgrade

By OTA
Check damage of CI slot pin Replace
Or damage of CI CAM Main B/D N
Or Normal
Download Picture?
CI+ Key
Y

Close Close

Old version of CI+ 1.2 CAM is not worked at the TV that is supported CI+ 1.3
 Check SVC Bulletin
Contents of LCD TV Standard Repair Process Detail Technical Manual
Continued from previous page

No. Error symptom Content Page Remarks

21 Check front display LED A17

22 B. Power error_No power Check power input Voltage & ST-BY 3.5V A18

24 POWER BOARD voltage measuring method A5

B. Power error_Off when on, off while
26 POWER OFF MODE checking method A22
viewing
Checking method in menu when there is no
28 A24
audio
C. Audio error_No audio/Normal video
Voltage and speaker checking method when
29 A25
there is no audio
C. Audio error_Wrecked Voltage and speaker checking method in
30 A25
audio/discontinuation case of audio error
D. Function error_ No response in
31 Remote controller operation checking method A27
remote controller, key error
Standard Repair Process Detail Technical Manual
Error Established
symptom A. Video error_No video/Normal audio date
LCD TV Revised
Content Check Back Light On with naked eye date A1

<LF49>

Power On -> disjoint back case -> check lighting at 2 points.

Standard Repair Process Detail Technical Manual
Error Established
symptom A. Video error_No video/Normal audio date
LCD TV Revised
Content LED driver measuring method date A2

<LF49>

Check the VLED (56V)

<28LB49>

6 Pin (MainBoard↔ Module)

1 FB1

2 FB3

3 VLED

4 VLED

5 NC

6 FB2

<22LB49>
6 Pin (MainBoard↔ Module)
1 FB1

2 FB1

3 VLED

4 VLED

5 FB2

6 FB2
Standard Repair Process Detail Technical Manual
Error Established
symptom A. Video error_No video/Normal audio date
LCD TV Revised
Content Check White Balance value date A3

<ALL MODELS>

Entry
Entry method
method

1.
1. Press
Press the
the ADJ
ADJ button
button on
on the
the remote
remote controller
controller for
for adjustment.
adjustment.

2.
2. Enter
Enter into
into White
White Balance
Balance of
of item
item 6.
10.

3. After
3. After recording
recording the
the R,
R, G,
G, B
B (GAIN,
(GAIN, Cut)
Cut) value
value of
of Color
Color Temp
Temp (Cool/Medium/Warm),
(Cool/Medium/Warm), re-
re-
enter the value after replacing the MAIN BOARD.
enter the value after replacing the MAIN BOARD.
Standard Repair Process Detail Technical Manual
Error Established
symptom A. Video error_No video/ Audio date
LCD TV Revised
Content Main Board Voltage measuring method date A5

<ALL MODELS>

C8302

Checking method
- Check the voltage of C8320 ( 19V )
Standard Repair Process Detail Technical Manual
Error Established
symptom A. Video error_Video error, video lag/stop date
LCD TV Revised
Content TUNER input signal strength checking method A6
date

<ALL MODELS>

MENU  support  signal test

 select channel

When the signal is strong, use the

attenuator (-10dB, -15dB, -20dB etc.)
Standard Repair Process Detail Technical Manual
Error Established
symptom A. Video error_Video error, video lag/stop date
LCD TV Revised
Content LCD-TV Version checking method A7
date

<ALL MODELS> 1. Checking method for remote controller for adjustment

Version

Press the IN-START with the remote

controller for adjustment
Standard Repair Process Detail Technical Manual
Error A. Video error _Vertical/Horizontal bar, residual Established
symptom image, light spot date
LCD TV Revised
Content LCD TV connection diagram (1) date A8

<LF49>

As the part connecting to the external input, check the screen condition by signal
Standard Repair Process Detail Technical Manual
Error Established
symptom
A. Video error_Video error, video lag/stop
LCD TV date
TUNER checking part Revised
Content date A9

<LF49>

Checking method:
1. Check the signal strength or check whether the screen is normal when the external device is connected.
2. After measuring each voltage from power supply, finally replace the MAIN BOARD.
Standard Repair Process Detail Technical Manual
Error Established
symptom
A. Video error, Color error
LCD TV date
Check and replace Link Cable(LVDS) and contact condition Revised
Content date A10 , A11

<LF49>

1. Check and replace LVDS Cable

2. Check LVDS connection condition
Standard Repair Process Detail Technical Manual
Error Established
symptom
A. Video error_Color error
LCD TV date
Adjustment Test pattern - ADJ Key Revised
Content date A12

You can view 6 types of patterns using the ADJ Key

Checking item : 1. Defective pixel 2. Residual image 3. MODULE error (ADD-BAR,SCAN BAR..)
4.Video error (Classification of MODULE or Main-B/D!)
Appendix : Exchange LVDS Cable or Main B/D (1)

Solder defect, CNT Broken Solder defect, CNT Broken Solder defect, CNT Broken

Solder defect, CNT Broken T-Con

T-Con Defect,
Defect,
Solder
T-Con CNT
defect,
Defect, CNT
CNT
CNT Broken
Broken
Broken
Broken Abnormal Power Section

Solder defect, Short/Crack Abnormal Power Section Solder defect, Short/Crack

Appendix : Exchange LVDS Cable or Main B/D (2)

Abnormal Power Section Abnormal Power Section Solder defect, Short/Crack

Solder defect, Short/Crack Fuse Open, Abnormal power section Abnormal Display

GRADATION Noise GRADATION

Appendix : Exchange the Module (1)

Panel Mura, Light leakage Panel Mura, Light leakage Press damage

Crosstalk Press damage Crosstalk

Un-repairable Cases
In this case please exchange the module.

Press damage
Appendix : Exchange the Module (2)

Vertical Block Vertical Line Vertical Block

Source TAB IC Defect Source TAB IC Defect Source TAB IC Defect

Horizontal Block Horizontal Block Horizontal line

Gate TAB IC Defect Gate TAB IC Defect
Gate TAB IC Defect Gate TAB IC Defect Gate TAB IC Defect

Un-repairable Cases
In this case please exchange the module.

Horizontal Block
Gate TAB IC Defect
Gate TAB IC Defect
Standard Repair Process Detail Technical Manual
Error Established
symptom B. Power error _No power date
LCD TV Revised
Content Check power input voltage and ST-BY 3.5V A18
date

<LF49>

L2403
Standard Repair Process Detail Technical Manual
Error Established
symptom B. Power error _Off when on, off whiling viewing date
LCD TV Revised
Content POWER OFF MODE checking method date A22

<ALL MODELS>

Entry method

1. Press the IN-START button of the remote controller for adjustment

2. Check the entry into adjustment item 3

Standard Repair Process Detail Technical Manual
Error Established
symptom C. Audio error_No audio/Normal video
LCD TV date
Revised
Content Checking method in menu when there is no audio date A24

<ALL MODELS>

Checking method
1. Press the MENU button on the remote controller
2. Select the SOUND function of the Menu
3. Change TV Sound Out to TV Speaker
Standard Repair Process Detail Technical Manual
Error Established
symptom C. Audio error_No audio/Normal video date
LCD TV Revised
Content Voltage and speaker checking method A25
when there is no audio date

<LF49>

L5400

Checking order when there is no audio

① Measure the 19V input voltage supplied from L5400 of Main Board
(If there is no input voltage, Replace Main Board)

② Connect the tester RX1 to the speaker terminal and if you hear the Chik Chik sound when you touch the GND
and output terminal, the speaker is normal.
Standard Repair Process Detail Technical Manual
Error D. Function error_ No response in remote controller, Established
symptom key error date
LCD TV Revised
Content Remote controller operation checking method date A27

<LF49>

P4102
1 GND
2 KEY1
3 KEY2
③ 4 +3.5V_ST
5 GND
6 LOGO/LED_R
④ 7 IR
8 GND
9 EYE_SCL
10 EYE_SDA
②
①

Checking order
1, 2. Check IR cable condition between IR & Main board.
3. Check the st-by 3.5V on the terminal 4.
4. When checking the Pre-Amp when the power is in ON condition, it is normal when the Analog
Tester needle moves slowly, and defective when it does not move at all.