LH-Series, Low-Height Skidding System

▼ LH-Series, Low-Height Skidding System

Low-Height Skidding
System for Heavy Loads
The Ideal Low-Height
Jack & Slide Solution

Skidding Systems
The Skidding System is comprised
of a series of skid beams moved by
• Low starting height saves time and increases versatility hydraulic push-pull cylinders, travelling
over a pre-constructed skid track.
• Portable design allows for easy transport and setup
A series of special PTFE-coated Teflon® pads
• System can push or pull load without relocating skidding cylinder are placed on the skid tracks to reduce friction.
• Skid track sections bolt together to allow each setup to be The push-pull cylinders are then connected by
hydraulic hoses to our Split-Flow Pump. The
customized as needed
Split-Flow Pump can be mounted on an optional
• Replaceable PTFE skid pads lower the total cost of ownership. pump cart for easy transport.
An optional storage and transport frame easily
holds the equipment in between use.

▼ LH400, Low-Height Skidding System provides the service team with the ability to maneuver and ▼ LH400 Skidding used to remove an old press from a
transport a press frame. facility to make room for new equipment.

358 www.enerpac.com
 Low-Height Skidding System
Low-Height Skidding Jack
Starter Kit - LH400SKW
LH400SKJ Starter Kit
includes:
Model
Numbers
Qty
LH
A complete starter kit is available Push-Pull Unit (1780 kN) LHPP25 2x Series
to fit the needs of any jack and Skid Beam A (1 meter) LHSB1A 2x
slide application. This system comes with
Skid Beam B (1 meter) LHSB1B 2x
two skidding units that will support up to
3560 kN in total. This kit will get the job Skid Track (1 meter) LHST1 10x
done, but there are optional accessories Split-Flow Pump (400V, 3 ph) SFP213MW 1x
available in addition (see page 360-361). Pump Cart (for SFP-pump) LHPC 1x
Each skidding unit will have 1 push-pull Hydraulic Hoses (15 m) HC7250C 4x Skidding Capacity with two push-pull units:
unit, 2 skid beams, 5 skid tracks, and
2 hoses.
Storage/Transport Frame LHSF 1x 3560 kN
The Split-Flow Pump has 2 outlets and can Push-Pull Stroke:
be easily towed on the pump cart. After the 600 mm
job is complete, components can be stowed
on the included storage frame. Maximum Operating Pressure:
700 bar

1 2 3 4 5
SFP-Series, Split-Flow Pump
Split-Flow pumps distribute an
equal amount of hydraulic oil to a
maximum of 8 outlets. Smart valve
technology allows both controlled
lifting and lowering of heavy loads.

Page: 336

LHPC Pump Cart

LH-Series, Low-Height Skidding System Requirements The LHPC pump cart easily tows
1 Skid Track LHST1 Required pump around jobsite and can be
2 Skid Beam LHSB1A + LHSB1 Required used with all models of SFP-Series
Split-Flow Pumps.
3 Push-Pull Cylinder Unit LHPP25 Required
4 Hydraulic Hoses Required
5 Split-Flow Electric Pump SFP Required
6* Track Support Application dependant
7* Storage-Transport Frame LHSF Optional Hydraulic Power Packs
8* Pump Cart LHPC Optional Enerpac offers a comprehensive
* not shown range of hydraulic power packs
that are optimized for use with
Skidding Systems.
LH400, Low-Height Skidding System (dimensions in mm)
749 1640
329 640 325 675
Hoses
Distribution Distribution Distribution Distribution

Enerpac offers a complete line of

260

Load Load Load Load

Load
Distribution
Load
Distribution
Load
Distribution
Load
Distribution

high quality hydraulic hoses.

To ensure the integrity of your
2874 system, specify only genuine
Enerpac hydraulic hoses.
172

477,5 477,5 477,5

92

128
153

Page:

359
 LH-Series, Low-Height Skidding Components
▼ LHPP25 Low-Height Push-Pull Unit
Push-Pull Unit
• Connects to first skid beam to push
or pull load along skid track
• Easily reverse direction by switching
reaction tabs
• Complies to ASME B30.1 and other
safety standards.

▼ Low-Height Push-Pull Unit

Maximum Model Stroke Weight
Capacity Number
(kN)
Push Pull (mm) (kg)

222 97,8 LHPP25 600 111

▼ LHSB1A and LHSB1B Skid Beams

Skid Beams
• Interlocks without any fasteners to
slide load over skid track;
skid beam A (LHSB1A) attaches to
the push-pull unit
skid beam B (LHSB1B) attaches to
skid beam A
• Polished stainless steel skid surface
• Carrying handles for easy transport.

▼ Skid Beams
Capacity Model Weight
Number

(kN) (kg)

890 LHSB1A 66
890 LHSB1B 63

◀ Details of push-pull
unit of LH400.

360 www.enerpac.com
 Low-Height Skidding Components
▼ LHST1 Skid Track
LH
Series

Skidding Capacity with two push-pull units:

3560 kN
Push-Pull Stroke:
600 mm
Maximum Operating Pressure:
700 bar

Skid Track
Teflon® Pads
• Support the load for skidding operations
A series of special PTFE coated
• Track sections bolt together Teflon® pads are placed on the
• Includes 9 pieces easily replaceable PTFE skid pads. skid tracks. The PTFE surface is
matched with the skid beam and
designed to achive minimum friction coefficients.
Replacement Teflon® Pads come in packs of
12 pieces. Order model number HSKSPS1.
▼ Skid Track
Maximum Model Track Weight
Capacity Number Length (incl.
(per skid track) pads)
(kN) (mm) (kg) Storage and Transport Frame
890 LHST1 955 67 For easy storage and transport
of all low-height skidding
components.

Fits following components:

2x LLPP25 Push-Pull Unit
2x LHSB1A Skid Beam A
▼ An LH400 Skidding System allows the 2x LHBS1B Skid Beam B
maintenance team to transport transformers ▼ Low-Height Skidding System assembly 10x LHST1 Skid Tracks
with access limitations. (LH400).
Model Overall Dimensions
Number LxWxH

(mm) (kg)

LHSF 1080 x 935 x 895 200

With all components stored dimensions are:
1080 x 935 x 1003 mm, and total weight 1350 kg.

361