GOVERNMENT OF RAJASTHAN

WATER RESOURCES DEPARTMENT

BASIC SCHEDULE OF RATES 2023

KOTA ZONE
(EFFECTIVE FROM 14 / 08 / 2023)

CHIEF ENGINEER
WATER RESOURCES ZONE
KOTA
 CONTENTS

Chapter Particulars Page

GENERAL NOTES 1-1
BASIC RATES
I LABOUR RATES 2-3
II SUPPLY OF MATERIAL 4-7
III CARRIAGE OF MATERIAL 8-9
IV HIRE CHARGES OF MACHINERIES 10-11

MAIN WORKS
V EARTHWORK IN EXCAVATION / EMBANKMENT 12-19
AND PROTECTION WORKS
VI MORTAR 20-20
VII MASONRY 21-23
VIII PLASTER AND POINTING 24-25
IX CONCRETE AND CANAL LINING 26-33
X CENTERING, SHUTTERING AND RCC 34-35
XI FOUNDATION AND SURFACE TREATMENT 36-39
XII GATES AND ALLIED WORKS 40-52
XIII PIPES / FITTINGS / SPECIALS 53-65
XIV MICRO IRRIGATION 66-71
XV TUNNEL AND ALLIED WORKS 72-74

MISCELLANEOUS AND ALLIED WORKS

XVI SURVEY, INVESTIGATION AND TESTING 75-84
XVII DISMANTLING & DEMOLISHING WORKS 85-85
XVIII MISCELLANEOUS WORKS 86-94
XVIII (A) MISCELLANEOUS WORKS 95-96
MISCELLANEOUS WORKS 97-98
XIX COMPENSATION OF PROPERTIES 99-108

USEFUL INFORMATION
Annexure I to XII From 109
Annex. I List of relevant IS codes
Annex. II Material consumption of main items
Annex. III Grading of Aggregate & Classes of Bricks
Annex. IV Weight of Building Material
Annex. V Reinforcement Characteristics
Annex. VI Weight of Structural Steel Section
Annex. VII Conversion Factors
Annex. Strange's Table
VIII IX Preliminary Design of Spillway
Annex.
Annex. X Soil Characteristics
Annex. XI Concrete Finishes
Annex. XII Extract from IS: 4826-1979
BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

GENERAL NOTES
1 Notes have been given before each chapter wherever necessary, which
must be read thoroughly before using the B.S.R. for incorporating
appropriate provisions and specifications in estimates and tender
documents.
2 Rates are for complete finished items and inclusive of all ancillary
works necessary for the completion of work covered under respective
item as per Indian standard specifications unless otherwise specified in
the description of the item.

3 Rates of all items provided in this BSR are inclusive of labour welfare,
camping, medical and sanitation facilities to labour, tools and plants
etc., required to complete the work as per Indian standard
specifications.
4 In case of disputes if any, regarding interpretation of the description of
items in this Schedule of Rates, the decision of the Chief Engineer,
Water Resources Rajasthan, Jaipur shall be final and binding.

5 PPC Cement shall be used unless otherwise specified. For concrete mix
design, use of flyash is permitted only with OPC cement.
6 If for any specific work, any item not included in this BSR is required
to be used, the relevant item and corresponding rates shall be adopted
from prevailing BSR of PWD/PHED, Rajasthan as the case be.
Similarly, for plantation works, rates and items from Forest BSR shall
7 be
Foradopted.
items related to Solar Power generation, rates approved by
Rajasthan Renewable Energy Corporation Limited (RRECL) shall be
adopted.
8 Further, for SCADA & PLC Works which are not available in WRD
BSR, the same may be adopted from Chapter-46 of RUIDP Integrated
Schedule of Rates-2022.

6
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER-I

LABOUR RATES
1 The labour rates are inclusive of all allowances including weekly holidays, no extra payment will be
admissible on this account.
2 The rates of skilled and unskilled labour's are inclusive of necessary tools, which are normally carried
by them according to the trade practice.
3 The rates are exclusive of labour cess, GST and contractor's profit unless otherwise specified.
4 Labour rates shall be governed by minimum wages act in force.
5 These rates are for analysis and estimation purpose only.
6 The grade designation of labour will be determined as per class and quality of the work skill of the
labour and work desired from labour
7 Rates for item no 20 are applicable only for limited period daily basis, if it is to be employed on
monthly basis, rates approved by finance department shall be applicable.

S. No. Item Unit Rate in Rs.

UNSKILLED
1 (a) Beldar/ Coolie / Chowkidar / Water man / Earth- dresser Per Day 300.00
(b) White washer/store or laboratory attendant/floor polisher Per Day 335.00
(c) Dak Runner with his own cycle Per Day 300.00
(d) Sweeper part time
(i) For 2 hours 90.00
(ii) For 1/2 day (Four hours) 160.00
(iii) Per Day 300.00
SEMI SKILLED
2 Mate Per Day 325.00
3 (a) Helper for Steel fabricator / Driller / Truck / Tractor /Compressor/ Per Day 360.00
Jack Hammer /Dumper
(b) Helper for Mason/ Mistri / Painter/ Carpenter/ Electrician Per Day 360.00
/Black Smith / Plumber / Survey Work/Fitter
4 (a) Security Guard with licensed gun owned by him Monthly 15660.00
Charges for Reliver, P.F., ESI, Service Charges, CGST, SGST are
extra
(b) Security Guard without gun Monthly 14260.00
Charges for Reliver, P.F., ESI, Service Charges, CGST, SGST are
extra
5 Munshi/Survey Amin/ Density Observer/ Record Keeper/Time
Keeper/ Gate Keeper/ Core Observer/ Laboratory Assistant /
Gauge Reader / Telephone Assistant
(a) Grade I Per Day 450.00
(b) Grade II Per Day 395.00
6 Cook cum Chowkidar Per Day 310.00
7 Stone breaker (unsing Ghan) / Turriya
(a) Grade I Per Day 420.00
(b) Grade II Per Day 380.00
8 Chawalia Per Day 380.00

2 LABOUR RATES
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

9 Operator for Jack Hammer/ Vibrator/ Pneumatic Tamper or Per Day 490.00
pavement Breaker/shot-crete placer
10 Gardener
(a) Grade I Per Day 355.00
(b) Grade II Per Day 310.00
SKILLED
11 Mason/ Painter/ Carpenter/ Electrician /Black smith / Plumber
(a) Grade I Per Day 540.00
(b) Grade II Per Day 490.00
12 (a) Survey Mistry / earthwork Mistry / Work Mistry Per Day 540.00
(Experienced/Trained) / Tracer (I.T.I.) / Wireless Operator
(Trained) / Receptionist
(b) Patwari / Amin (Trained / Retired) Per Day 730.00
(c) Supervisor for Civil work / HEM Works Per Day 625.00
13 Welder/Fitter/Line-man/Turner/Wireman/Driller Per Day 540.00
14 Stone Dresser/cutter (Silawat)
(a) Grade I Per Day 540.00
(b) Grade II Per Day 490.00
15 Boat man/Blaster (with license) Per Day 730.00
16 Divers with life jackets and all accessories for working under Per Hour 1405.00
water. Payment shall be made for Duty hours at site up to 5 meter
water depth
(a) Add extra if water depth is more than 5 meter but less than 10 Per Hour 25 % extra
meter above item 16
(b) Add extra if water depth is beyond 10 meter Per Hour 50 % extra
above item 16
17 Light vehicle driver for Jeep/Car/Station wagon etc. (License Per Day 625.00
holder) (Grade I)
18 (a) Driver for pumps/Concrete Mixers Per Day 490.00
(b) Driver for Compressor/ Generators/ DG Set/ Grout pump/Driller Per Day 490.00
(c) Heavy vehicle driver for Trucks/Dumpers/Tractors/ Stone crusher Per Day 675.00
etc. (License holder)/ Crane operator
19 Driver for Heavy Machine like chain type Dozers/Shovels, Per Day 705.00
Excavator (Long Boom), JCB Operator Chain type/Tyre Mounted
etc. (License Holder) Boring/Wagonet machine operator
20 (a) Typist having knowledge of typing in computer Per Day 540.00
(b) Computer Operator having knowledge of M.S.
Office/Excel/Power point
(i) with own computer Per Day 650.00
(ii) without computer Per Day 540.00
21 Work Agents/Surveyors/Supervisors
(a) Civil Engineer Possessing Degree or equivalent. Per Day 1300.00
(b) Civil Engineer Possessing Diploma or equivalent. Per Day 865.00
22 Auto CAD ( civil ) / GIS operator
(a) Having experience More than 5 year Per Day 1080.00
(b) Having experience of 1 -5 years Per Day 760.00
23 Surveyor for Total Station / DGPS instrument Per Day 865.00
24 Surveyor for Social/ Economic/ Demographic survey Per Day 865.00

3 LABOUR RATES
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER - II
SUPPLY OF MATERIALS
NOTES:
1 These rates are at work site inclusive of all taxes, GST, Contractor's profit, overheads & royalty
etc. unless otherwise specified.
2 Measurments shall be made on the basis of stacks and effective height for payment purpose will
be as prescribed below. No separate payment shall be made for laying of stacks.
3 Effective height of stacks for various materials shall be as under:
(i) Stone,boulders,brick bats,morrum,sand,surkhi,flyash etc. 85 % of Av. Ht.
(ii) Un-slacked lime, aggregates etc. 90% of Av. Ht.
4 These rates are for analysis and estimation purpose only.

S.No Item Unit Rate

1 (i) Crusher broken stone aggregate of various sizes in accordance with

IS:383 for concrete work for dams, canals, and other important
structures, well graded with size of aggregate including all lead and lift.
(a) 150 to 80 mm size Cum 800.00
(b) 80 to 40 mm size Cum 900.00
(c) 40 to 20 mm size Cum 1050.00
(d) 20 to 10 mm size Cum 1100.00
(e) 10 to 4.75 mm size Cum 1000.00
(ii) Hand broken stone aggregate of various sizes in accordance with
IS:383 for concrete work for dams, canals, and other important
structures, well graded with size of aggregate including all lead and lift.
(a) 150 to 80 mm size Cum 680.00
(b) 80 to 40 mm ( Hand broken) Cum 770.00
(c) 40 to 20 mm ( Hand broken) Cum 890.00
(d) 20 to 12.5 mm ( Hand broken) Cum 940.00
2 Stones for Random Rubble masonry work at least 90% stones weighing Cum 960.00
not less than 37.50 Kg. and no dimension less than 23 cm for massive
work including all lead and lift.
3 Stones for Random Rubble masonry, at least 75% stones not less than Cum 900.00
15 cm in size in any direction and weighing not less than 23 kg
including all lead and lift.
4 C.R. Masonry stone for face work of massive structures duly hammer Cum 2484.00
dressed on all beds and sides, the beds joints & faces shall be chisel
dressed for at least 8 cm back from face and at least 4 cm from sides
height not less than 25 cm and weighing not less then 50 kg., 50%
stones to have depth more than 45 cm & tail area not less than half the
face area including all lead and lift.
5 (a) C.R. Masonry stone for face work of general structures duly hammer Cum 2403.00
dressed not less than 20 cm in any direction and at least 50% stones to
be more than 23 cm in depth including all lead and lift.
(b) C.R. stones headers, hammer dressed finished size not less than 20 cm Cum 2643.00
x 20 cm and depth not less than 30 cm
6 Stones for soling, boulder for rock toe, toe drain, rock fill etc. not less Cum 820.00
than 15 cm in any direction including all lead and lift.

4 SUPPLY OF MATERIALS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

(a) Quarry spalls properly screened and graded but not more than 10 cm Cum 550.00
and not less than 10 mm in size including all lead and lift.
(b) Quarry rubish not more than 10 cm in size including all lead and lift. Cum 400.00
8 (a) Pitching stones atleast 75% stones to be more than 40 kg, in weight and Cum 1100.00
23 cm x 25 cm x 30 cm in size including all lead and lift.
(b) Pitching stones atleast 75% stones to be more than 25 kg, in weight and Cum 990.00
20 cm x 20 cm x 23 cm in size including all lead and lift.
(c ) Stones for Rip-Rap at least one side not less than 23 cm in size Cum 910.00
including all lead and lift.
(d ) Stones for Rip - Rap at least one side not less than 15 cm in size. Cum 825.00
9 (a) Cement PPC (in bags) 50 Kg in weight. As per IS 1489 and IS 8112 Bag 315.00
(excluding cost of empty bag).
(b) Cement OPC (in bags) 50 Kg in weight. As per IS 1489 and IS 8112 Bag 350.00
(excluding cost of empty bags).
(c) Super Sulphate Cement (in bags) 50 Kg in weight. (excluding cost of Bag 400.00
empty bags).
10 Bentonite (powder form) Kg 4.55
11 Unslaked Lime (Sojat or equivalent) including all lead and lift. Cum 4900.00
12 Surkhi pulverized as per IS specification i.e., passing through IS Sieve Cum 900.00
No. 9 including all lead and lift.
13 Natural Sand (Un-screened) including all lead and lift. Cum 1200.00
14 Natural Sand screened and free from organic and deleterious material Cum 1400.00
including all lead and lift.
15 Natural Aggregate including all lead and lift.
(a) 150 to 80 mm size Cum 600.00
(b) 80 to 40 mm size Cum 675.00
(c) 40 to 20 mm size Cum 790.00
(d) 20 to 10 mm size Cum 825.00
16 Morrum or Murda including all lead and lift. Cum 400.00
17 Supply of Steel including all lead and lift.
With out contractor Benefit
(a) Mild steel and medium tensile steel bars as per latest relevant IS code Kg 66.00
(b) HYSD steel bars as per latest relevant IS code Kg 72.00
(c) Structural steel as per latest relevant IS code Kg 74.00
18 Supply of bricks as per IS : 1077 including all lead and lift.
(a) Well burnt clay bricks (size 230x110x70 mm) class designation 100 as 1000 5750.00
per specification Nos
(b) Well burnt clay bricks (size 230x110x70 mm) class designation 75 as 1000 4820.00
per specification Nos
(c) Comman burnt clay bricks (size 230x110x70 mm) class designation 50 1000 4300.00
as per specification Nos
(d) Brick bats Cum 950.00
(e) Supply of pucca clay tiles (size 30 x 15 x 5 cm) class designation 105 1000 5600.00
as per IS:3367-1993 Nos
19 Hydraulically compressed P.C.C. tiles 40 mm thick (50 mm
compressed to 40 mm) in cement, sand, aggregate upto 10 mm (well
graded crusher broken) as per specifications conforming to ISI 10646-
1991 with concrete of M15 grade including all lead and lift.
(a) 300 x 300 mm size Each 27.00

5 SUPPLY OF MATERIALS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

(b) 150 x 300 mm size Each 14.00

20 Stone patties edges hammer dressed including all lead and lift.
(a) Length up to 1.50 m and thickness 50 mm and above Sqm 675.00
(b) Length up to 1.50 m to 2.50 m and thickness 70 mm and above Sqm 800.00
(c) Length up to 2.50 m to 4 m and thickness 80 mm and above Sqm 900.00
21 Cut stone sills, slab, or lintels one face plain and edge hammer dressed
including all lead and lift.
(a) 100 to 125 mm thick Sqm 625.00
(b) 126 to 150 mm thick Sqm 750.00
(c) 151 to 200 mm thick Sqm 850.00
22 Fly ash confirming to IS 3812 ( in bags) 20 Kg in weight including all Per bag 50.00
lead and lift.
23 Chemical for curing as per ASTM Per Lit 60.00
24 Empty bag of 50 kg capacity in good condition
(a) Jute Each 25.00
(b) Plastic / Polythene Each 10.00
25 ISI marked low Density Poly Ethylene (LDPE) film black, High Impact Kg. 190.00
resistant, Heavy duty Grade 030 in thickness of 125, 200 & 250 micron
in the form of flat sheet of 6 to 9 metre width without having any joints
as per IS: 2508
26 (a) Distance stone well dressed of required shape and size 60 cm x 23 cm x Each 300.00
7 cm with exposed faces chiesel dressed.
(b) Distance stone well dressed of required shape and size 60 cm x 23 cm x Each 350.00
7 cm with distance marked engraved and exposed faces well painted.
27 Cost of Diesel Lit 94.00
28 Amonium nitrate Kg 70.00
29 Gelatin emulsion type Kg 82.00
30 Fuse Coil RM 12.00
31 Ordinary detonator Each 10.00
32 Drill Rod 800 mm long Each 4950.00
33 Electric Detonator Each 20.00
34 Sealing Compound Kg 60.00
35 Air hose double braided Mt 235.00
36 Claw coupling Each 55.00
37 Hose clamps Each 36.00
38 Valve 3" dia Each 2400.00
39 Suction pipe 3" dia Mt 425.00
40 Foot Valve 3" Each 550.00
41 GI pipe 3" dia Meter 750.00
42 Extension Rod 1¼" hex 800 mm Each 3650.00
43 Extension Rod 1¼" hex 1600 mm Each 7500.00
44 Extension Rod 1¼" hex 2400 mm Each 11000.00
45 Extension Rod 1¼" hex 3200 mm Each 18000.00
46 Coupling sleeves1¼" Each 1650.00
47 Shank Rod Each 7000.00
48 Bit 48 mm dia Each 2600.00
49 Water Body Each 1650.00
50 Water body washer Each 38.00
51 Lubricating oil litre 225.00

6 SUPPLY OF MATERIALS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

52 Grinding wheel Each 900.00

53 Bit adopter Each 1550.00
54 Shank adopter Each 6350.00
55 T.C.T. Cross bit Each 1950.00
56 GI/MS pipe 65 mm dia Mt 550.00
57 Blasting Powder kg 45.00
58 Blasting Fuse ( Fuse Wire) Each 17.00

7 SUPPLY OF MATERIALS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER - III
CARRIAGE OF MATERIALS
NOTES :
1 The rates of this chapter shall be applicable only when leads exceed 250 metres except mentioned
otherwise.
2 The distance between 250 metres to 750 metres shall be considered as ½ km lead, and that above
750 metres to 1500 metres shall be considered as 1km . Subsequent distance shall be rounded off by
ignoring less than 500 m distance and by considering a distance of 500 m and above as full
kilometre.
3 Item No. 4 will not be applicable for items of Chapter – II
4 These rates are at work site inclusive of all taxes, GST, Contractor's profit, overheads & royalty etc.
unless otherwise specified.
S.No Item Unit Rate
1 Carriage of Materials by mechanical transport including loading,
unloading and stacking , if stacking is not required no deduction is to
be done
Stone, Aggregate, Ballast, Sand, Lime, Surkhi, Fly-ash, Morrum,
Kanker etc.
(a) Lead up to ½ Km. Cum 90.00
(b) Lead up to 1 Km. Cum 98.00
(c) Lead up to 2 Km. Cum 115.00
(d) Lead up to 3 Km. Cum 131.00
(e) Lead up to 4 Km. Cum 147.00
(f) Lead up to 5 Km. Cum 163.00
(g) Lead beyound 5 km. but up to 20 km. for each subsequent km Cum 8.00
(h) Lead beyound 20 km. for each subsequent km Cum 8.00
2 Deduct if Loading is not done for stone, Aggregate, Ballast, Timber, Cum 65.00
Sand, Lime, Surkhi, Fly-ash, Morrum, Kanker etc.
3 Carriage of Materials by mechanical transport including loading,
unloading and stacking, if stacking is not required no deduction is to
be done for; Cement, Surkhi (Pulverized), Fly ash, Tar, Timber,
bricks, steel, cut stone etc.
(a) Lead up to ½ Km. M.T. 109.00
(b) Lead up to 1 Km. M.T. 115.00
(c) Lead up to 2 Km. M.T. 126.00
(d) Lead up to 3 Km. M.T. 135.00
(e) Lead up to 4 Km. M.T. 146.00
(f) Lead up to 5 Km. M.T. 155.00
(g) Lead beyond 5 Km but up to 20 km. for each subsequent km M.T. 6.00
(h) Lead beyond 20 Km but up to 50 km. for each subsequent km M.T. 6.00
4 Deduct if Loading is not done for Cement, Surkhi (Pulverized), Tar, M.T. 91.00
bricks, steel, cut stone etc.
5 Transportation of miscellaneous items like sign boards, tools and Truck 4968.00
plants, hume pipes, sanitary & electric goods, shuttering and Load (7-
centering etc.including loading, unloading and handling with care 10 MT
without making any damage lead upto 20 Km capacity)
(a) Add extra for each subsequent km beyond 20km over item No. 5 -do- 48.00
per km

8 CARRIAGE OF MATERIALS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

Note : Per truck load for hume pipes with or without collars shall be as follows :

SN Pipe (diameter) Nos.

1 2000/1500 mm dia 1
2 1200 mm dia 2
3 900/1000 mm dia 3
4 600 mm dia 6
5 450 mm dia 10
6 300 mm dia 15
7 150 mm dia 120
8 100 mm dia 150

9 CARRIAGE OF MATERIALS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER – IV

HIRE CHARGES OF MACHINERIES

NOTES :

These rates are for hiring private machinery in working condition for works and quotations/tenders will have to be
1
called with detailed terms and conditions and necessary action be taken as per G.F.&A.R./P.W.F.& A.R.
Watch & ward and essential repair including cost of spare parts to be replaced of machine is included in the rates given
2
below & shall be the responsibility of the owner of the equipment.
These rates are at work site inclusive of all taxes, GST, Contractor's profit, overheads & royalty etc. unless otherwise
3
specified.
Hire charges of Machine are taken for a day of 8 hours actual working (Machine in running condition) excluding rest
4
period. For part working up to 4 hours half day payment shall be made only.
5 Vehicle will remain available for any hour of the day to facilitate emergency tours.

6 Unauthorised run and it's diesel consumption will be liability of the owner of the vehicle
Hire charges Hire charges without
without diesel but diesel but with Provision for Idle
S. with operational operation staff
Hire charges for Machine / T&P Unit diesel per Km/or charges
No. staff M.oil, spares M.oil, spares &
per hr. (in liters) (in Rs.)
& lubricants (in lubricants (in Rs)
Rs) without GST / profit
1 Trucks upto 5 tonne capacity (light Day 950 766.70 0.20 Per Km 522.0
commercial vehicles)
2 Trucks 7-10 tonne capacity Day 1400 1129.90 0.25 Per Km 627.0
3 Dumpers 7-10 tonne capacity Day 1600 1291.40 0.25 Per Km 783.0
4 Tractors -
(a) Upto – 40 HP Day 650 524.60 0.20 per km 313.00
(b) Above 40 HP (for consolidation) Day 700 565.00 3.00 per hr 418.00
5 Tractor mounted compressor (upto 160 Day 750 605.30 3.00 per hr 470.00
cfm.) 0.20 Per Km
6 Air compressors (Stationary)
(a) Upto 160 cfm Day 750 605.30 3.00 per hr 418.00
(b) Above 160 cfm and upto 250 cfm Day 900 726.40 5.00 per hr 470.00
(c) 300 cfm to 350 cfm Day 1075 867.60 7.50 per hr 522.00
Jack hammer / Rock Breaker machine Day 450 363.20 157.00
7 without drill rod but with necessary
8 hosepipe
Driller Day 450 363.20 157.00
Concrete mixers
(a) 10/7 cft. capacity Day 550 443.90 1.00 per hr 261.00
(b) 14/10 cft. capacity Day 600 484.30 1.20 per hr 365.00
10 Mortar miller Day 475 383.40 1.00 per hr 261.00
11 Needle/surface vibrator (without staff) Day 325 262.30 0.80 per hr 63.00
12 Diesel driven generator
(a) Upto 6KVA Day 500 403.60 0.80 per hr 131.00
(b) Above upto 10KVA Day 600 484.30 1.60 per hr 146.00
(c) Above upto 25KVA Day 750 605.30 7.25 per hr 157.00
(d) Above upto 50KVA Day 850 686.00 12.00 per hr 209.00
13 Pumping sets
(a) 5 to 10 HP Day 400 322.80 0.80 per hr 209.00
(b) Above 10 HP to 16 HP Day 475 383.40 1.20 per hr 313.00
(c) Above 16 HP to 30 HP Day 525 423.70 1.60 per hr 365.00
14 Diesel Road roller 8 to 10MT Day 1200 968.50 5.00 per hr 522.00
15 Sheep's foot roller (without staff)

10 HIRE CHARGES OF MACHINERIES

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

(a) Capacity 5 MT Day 280 226.00 0.00

(b) Capacity 3 MT Day 225 181.60 0.00
16 Plain roller 3 MT (without staff) Day 180 145.30 0.00
Tractor Trolly above 2 Cum capacity
17 (without staff)
(a) Two wheeler with out hydraulic lift Day 250 201.80 - 73.00
(b) Four wheeler without hydraulic lift Day 300 242.10 - 84.00
(c) Four wheeler with hydraulic lift Day 350 282.50 - 94.00
18 Karawha Day 120 96.90 - 52.00
19 Water Tanker
(a) Wheel – mounted
(i) Upto 3000 Lit. capacity Day 300 242.10 - 125.00
(ii)Above 3000 but upto 5000 Lit. capacity Day 400 322.80 - 188.00
Truck- mounted 5000 Lit. to 8000 Lit. Day 1350 1089.60 0.25 per km 522.00
(b) capacity
Inspection Vehicles with driver such as
20 Car/Jeep/Bolero or equivalent Model not
older than 3 years (Two wheel drive)
for offices having a city (Municipal limit of per
(a) town as their jurisdiction) up to 1500 km Month 27900
per month including POL but excluding
GST
for offices having a district as their per
(b) jurisdiction up to 2000 km per month month 32900
including POL but excluding GST
for offices having juridiction more then one per
(c) district but less then state up to 2200 km per month 34900
month including POL but excluding GST
for offices having juridiction whole state per
(d) up to 2500 km per month including POL month 37900
but excluding GST
(e) Model not older then 2 years Day 900 726.40 0.07 per km
Hydraulic excavator/ loader like JCB/
Poclain, Hitachi etc. with all accessories
21 (for actual site working, idle period) having
bucket capacity
(a) upto 0.40 cum Hr. 625 504.40 5.00 per hr 313.00
(b) above 0.40 & upto 0.75 cum Hr. 1000 807.10 7.25 per hr 439.00
(c) above 0.75 cum Hr. 1400 1129.90 15.00 per hr 585.00
22 Dozer for spreading / levelling
(a) upto 100 HP Hr. 580 468.10 5.00 per hr 131.00
(b) above 100 & upto 175 HP Hr. 1050 847.50 15.00 per hr 407.00
(c) above 175 HP Hr. 1400 1129.90 20.00 per hr 501.00
23 Hiring of Fiber Boat
Power Driven with license 6 to 10 seat Per hr. 1650 1331.70 0.80 per hr 209.00
(a) capacity with operator
Manually operated with boatmen with Per hr. 1350 1089.60 - 125.00
(b) license 6 to 10 seat capacity
Grout pump including water hose, air hose, Day 500 403.60 104.00
24 fittings, repairs etc.
25 Vibro compactor with operator Day 4800 3874.10 8 Per Hr 574.00
26 Vibro sheep foot compactor with operator Day 5000 4035.50 8 Per Hr 679.00
27 Rent charge of Auto Level without men Day 475 383.40 - - -

11 HIRE CHARGES OF MACHINERIES

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER - V

EARTHWORK IN EXCAVATION / EMBANKMENT AND PROTECTION

NOTES
1 These rates are at work site inclusive of all taxes, GST, Contractor's profit, overheads & royalty
etc.
2 Mode of measurement and classification on nature of work as well as type of strata shall be
governed by IS:1200 (Part-I) and Hand Book of method of measurements: Publication No. SP-27
of Bureau of Indian Standards. (refer useful data in which extract copy of same is provided)

3 In case of earthwork in excavation and for embankment part A, B only "crow fly distance"
between C.G. of Embankment/spoil bank base to the C.G. of borrow area cut shall be considered
as "shortest practicable route" for the purpose of lead what so ever the case may be.

4 No payment for earthwork of ramps, approaches to embankments shall be made and cost of such
operation shall deemed to have been included in item rates given below.

5 No Payment for construction and maintenance of haul roads for approach to borrow area shall be
admissible and cost there of shall be deemed to have been included in the item rates given below.

6 The rates of earthwork for embankments are for complete item and includes allowance for
shrinkage due to compaction, wastage etc.

7 In case of earth work for bunds, the lift shall not be considered separately but shall be considered
with the lead as computed below : Total lead = 1.2(L+12H)
Where : L = Lead in meter as per note no 3
H = Height of weighted C.G. over base in meter.

8 The use of explosive in excavation shall not be considered as a "reason" for classification of
strata.
9 For Estimation Purpose classification of strata shall be inspected and approved by Executive
Engineer.
10 In case of change of strata from that as contemplated in the sanctioned estimate, prior
permission/approval of the Superintending Engineer should be invariably obtained.

11 In case, hard rock requiring blasting and having hardness more than 2 Mohs and quantity is more
than 500 cum, it shall be got checked and approved by the Superintending Engineer for payment.

12 No extra payment will be made for de-watering on any items of this chapter. In case dewatering is
not required for these items then no payment shall be deducted against these items.

13 Mix strata rate for canal excavation can be allowed by estimate sanctioning authority who will
ascertain the same based on details of sufficient trial pits to be applicable to canals having
discharge capacity less than 10 cusecs and limited to 2 m depth of cutting and water courses of
minor tanks & minors and water courses of major & medium projects.
14 Rate of earth work in excavation is including the cost of dewatering/ planking/ shoring/ timbering
/ strutting / barricading if any required at site.

12 EARTHWORK IN EXCAVATION/EMBANKMENT AND PROTECTION WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

S.No. Item Unit Rate

PART "A" : EARTH WORK IN EXCAVATION
WORK TO BE EXECUTED BY MECHANICAL MEANS
1 Excavation including loading, unloading, disposal and dressing of
excavated earth within initial lead of 50m and lift up to 1.5m including
dressing of excavated area and dewatering wherever required complete in
all respect soil
(a) Soft/Loose Cum 92.00
(b) Hard / dense soil Cum 95.00
(c) Hard soil mixed with Kankar / boulders, Morrum Cum 118.00
Excavation including loading unloading disposal and dressing of
excavated rock within initial lead of 50m and lift upto 1.5m in dry or
moist including dressing of excavated area, de-watering wherever
required complete in all respect.
(a) Soft / Disintegrated rock Cum 161.00
(b) Hard rock not requiring blasting Cum 241.00
(c) Phylite & other hard rock requiring nominal blasting Cum 346.00
(d) Hard rock (dry or moist) requiring blasting (where hardness of rock is Cum 446.00
more than 2) including disposal of excavated material in the designated
spoil bank / embankment, dressing of excavated material and dewatering
with all leads & lifts of excavation and disposal. The contractor is free to
use the usable excavated stone else where for which any transition
expenditure & royalties, tax etc if required to be paid then it will be
liability of contractor as the cost of usable stone has already been
deducted from the rate.
3 Excavation with line drilling, controlled blasting near structures,
populated area (situated within 50m) including dewatering, loading,
unloading, disposal & dressing within initial lead of 50m and lift upto
1.5m complete in all respect in dry or moist and also including
compensation of damages if any , in :
(a) Phylite and other hard rock requiring nominal blasting Cum 561.00
(b) Hard rock (dry or moist) requiring blasting (where hardness of rock is Cum 636.00
more than 2) including dewatering, disposal of excavated material in the
designated spoil bank/ embankment and dressing of excavated material
with all leads & lifts of excavation and disposal. The contractor is free to
use the usable excavated stone else where for which any transition
expenditure & royalties, tax etc if required to be paid then it will be
liability of contractor as the cost of usable stone has already been
deducted from the rate.

4 Final excavation by line drilling including removing of hard rock by Cum 1079.00
wedging and barring and chiseling near final levels (only upto 0.3 m
depth) without resorting to blasting including dewatering, disposal of
excavated material within initial lead of 50m and lift of 1.5m complete in
all respect
5 Excavation for foundation of Dam in seams/faults and at other confined Cum 1263.00
places nearer to Abutment, peir, wings etc. in hard rock by line drilling /
rock breaker including dewatering, disposal, loading, unloading and
dressing of excavated material within initial lead of 50m. and lift upto
1.5m complete in all respect.
6 Loading , Unloading and Disposal of land slide soil / earth/ sand/ pebbles Cum 188.00
/ malba/ debris / rubbish / stone pebbles / rock mass including breaking
of big boulders (if required) within initial lead of 50 m and lift up to 1.50
m.

13 EARTHWORK IN EXCAVATION/EMBANKMENT AND PROTECTION WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

7 Removal of slit/soil/earth, sand, pebbles, 'Malba', debris, rubbish, stone

pebbles & obstruction deposited in canal bed up to design line grade and
sections having design due to erosion/scour/slips in canal banks/silting
with or without bushes and weeds etc. in dry or moist condition from
canal bed including dewatering, loading unloading and disposal at
suitable place as directed by Engineer in charge with initial lead of 50m.
and lift upto 1.5 m with proper dressing on canal bed complete in all
respect
(a) For 5 to 15 cms depth, having
(i) Unlined section Sqm 18.00
(ii) Lined section Sqm 15.50
(b) For depth above 15 cms but upto 30cms having
(i) Unlined section Sqm 32.00
(ii) Lined section Sqm 28.00
Measurements of works for item No. 7 (a) & 7 (b) shall be limited to
canal bed area only
(c) For depth above 30cm. Cum 90.00
(d) Extra on item 7(c) only if silt clearance is done under water & mud. Cum 23.00
8 Re-handling of excavated material including loading unloading and
dressing within initial lead of 50 m and lift of 1.5m with cost of de-
watering wherever required and all applicable taxes and levies etc.
complete in all respect
(a) Earth / Soil Cum 88.00
(b) Mixed strata muck Cum 108.00
(c) Rock Cum 139.00
9 Extra charges for disposal of excavated/re-handled material in required
profile laid in uniform layers and given side slopes well dressed having
layer thickness including loading and un-loading wherever required with
cost of dewatering wherever required complete in all respect
(a) Not exceeding 15cm Cum 9.50
(b) Not exceeding 20 cm Cum 8.10
10 Extra lead over item no 1 to 8 of excavated material.
(a) Beyond initial lead of 50 m & upto 250 m Cum 9.50
(b) Add extra over item 10 (a) for lead beyond 250m & upto 750m Cum 8.75
(for average 1/2Km).
(c) Add extra for each subsequent lead of 500m or part, there of beyond ½ Cum 8.50
Km. & upto 5 Km
(d) Add extra for each subsequent lead of 1 km or part there of beyond 5 Km Cum 8.50
11 Add extra over item No. 1 to 8 for disposal of excavated material above Cum 8.50
initial lift of 1.5m and for every additional lift of 1.5m or part there of
including loading and un- loading wherever required
12 Add extra over item No. 1 to 5 for excavation under water for all type of Cum 25%
strata including dewatering charges. (Quantity under water during actual
work is only to be considered) Quantity of excavation below water level
in foundation area during continous pump running should only be
considered.
13 Refilling the excavated earth (excluding rock) in trenches, plinth side of Cum 91.00
foundations etc. in layers not exceeding 20 cm in depth, consolidating
each deposited layer by ramming and watering including cost of water,
loading and un-loading wherever required with cost of dewatering
wherever required.

14 EARTHWORK IN EXCAVATION/EMBANKMENT AND PROTECTION WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

14 Filling in plinth with locally available river shingle under floors including Cum 394.00
watering , ramming , consolidating and dressing complete including cost
of shingle, and loading and un-loading wherever required with cost of
dewatering wherever required, complete in all respect
15 Earth work in excavation in foundation, trenches etc. including dressing
of sides and ramming of bottoms, including getting out the excavated
material, refilling after laying pipe/ foundation and disposal of surplus
excavated material at a lead upto 50m suitable site as per direction of
Engineer for following depths, below natural ground / Road top level.
15.1 In all types soils/ saturated soil such as morrum, sand, sandy silt, clay,
black cotton soil, kankar, etc.
(i) Depth upto 1.5 m Cum 192
(ii) Add extra for over all depth of excavation above 1.5 m and upto 3.0 m Cum 13
15.2 In ordinary rock.
(i) Depth upto 1.5 m Cum 820
(ii) Add extra for over all depth of excavation above 1.5 m and upto 3.0 m Cum 57
15.3 In hard rock (required blasting) including Blasting materials.
(i) Depth upto 1.5 m Cum 1377
(ii) Add extra for over all depth of excavation above 1.5 m and upto 3.0 m Cum 96
15.4 In hard rock (Blasting prohibited)
(i) Depth upto 1.5 m Cum 2776
(ii) Add extra for over all depth of excavation above 1.5 m and upto 3.0 m Cum 194
PART "B" : EARTH WORK IN EMBANKMENT
WORK TO BE EXECUTED BY MECHANICAL MEANS
16 Earth work in rough (borrow area) excavation for embankments in hard
soil, morrum or highly weathered strata dry or moist, including laying in
20 cm layers (before compaction) and breaking of clods, sorting of grass,
pebbles etc. and dressing when compacted by vibro compactor, vibro
sheep foot roller, sheep foot roller/pneumatic tyred roller to obtain dry
density of at least 98% of Standard Proctor's density with initial
lift of 1.5m (Excluding charges for compaction and watering) including
loading and un-loading wherever required complete in all respect.

(a) With initial lead of 250 m Cum 128.00

(b) With lead beyond 250 m and up to 750 m (½ Km) Cum 137.50
(c) Add extra for each subsequent lead of 500m or part there of beyond ½ Cum 8.75
Km and up to 5 km
(d) Add extra beyond 5km for each subsequent km. or part there-of. Cum 8.50
(e) Deduct if only carriage of earth is to be done (including unloading and Cum 56.00
placing on embankment in 15 cm layers)
17 (a) Deduct in item no 16 (a) to (d) above if Standard Proctor's density to be Cum 10.00
achived is at least 95%
(b) Deduct in item no 16 (a) to (d) above if Standard Proctor's density to be Cum 19.00
achived is at least 90%
18 Compaction of earth or highly weathered strata
(a) By manually or plain roller. (density 90% of Proctor) Cum 25.00
(b) By mechanical equipment such as sheep foot roller/ pneumatic tyred
roller/vibro compactor / vibro sheep foot compactor required as per site
condition to obtain dry density of.

15 EARTHWORK IN EXCAVATION/EMBANKMENT AND PROTECTION WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

(i) at least 95% of Standard Proctor's density Cum 39.00

(ii) at least 98% of Standard Proctor's density Cum 42.00
(c) Add extra over item No. 18 (b) for compaction in restricted area nearby Cum 20%
structure or flanks by hand rammers or by pneumatic tampers.
(d) Add Extra over item no 18 a & 18 b (i) for compaction of earth work sqm 24.00
only on side slope for resectioning / remodelling of existing canal by
mechanical compactor or any other mean on canal side slopes.
In this case no lip cutting shall be paid extra
19 Lip cutting and final dressing as per designed section including re- Sqm 34.00
handling and disposal of excavated earth in layers 20 cm on
embankments etc. with cost of dewatering wherever required, and
20 complete in
Benching all respect
base and disposal of the excavated material including dressing Cum 97.00
etc. complete within initial lead up to 50m and lift up to 1.5m
21 Labour charges including watering for puddle work to obtain minimum Cum 114.00
dry density as 90 % of M.D.D.
22 Construction of earthen dowel 0.50m top width and 0.40m height (area Per RM 152.00
0.40 sqm) including ramming, watering, & dressing etc. complete with all
lead and lift.
23 Dressing of uneven embankment in required profile Sqm 14.30
24 Scrapping of grass and shrubs Sqm 5.60
25 Ploughing and picking of surface of old embankment Per 10 4.60
sqm
26 Threading / turfing of grass on slopes of bunds etc. in rows 15 cm centre Sqm 83.00
to centre in each direction including Ploughing, levelling, breaking of
clods, and removal of stones etc. if required including maintenance for 30
days or more till the grass develops fully with all leads and lifts complete.
27 Repairs of rain cuts, gullies etc. on bunds embankments, canals and other extra on 20%
petty works. basic
28 Watering of earth including cost of carriage of water when source of
water is
(a) up to 1 Km Cum 12.60
(b) Beyond 1 Km but up to 5 Km extra per Km Cum 5.00
(c) Extra for every subsequent 1 Km or part thereof when source is more Cum 3.70
than 5 Km
29 Add extra for earth taken from private land with all lead and lift, land to Cum 35.00
be arrangged by contractor through private negotiations. Item applicable
on certification by E.E. that no Government land is available with 250
meters from borrow area.

PART C : PROTECTION WORK

30 Supplying and laying sand of grade as per design requirement in required Cum 1799.00
profile including all lead & lifts.This item is to be used only for laying
filter / inverted filter
31 Supplying and laying aggregate in layers and profile as specified
including all leads & lifts. This item is to be used only for laying filter /
invertedballast
(a) Broken filter 40 to 80 mm size Cum 1047.00
(b) Broken ballast 20 to 40 mm size Cum 1205.00
(c) River gravel 40 to 80 mm size Cum 936.00
(d) River gravel 20 to 40 mm size Cum 1079.00
(e) River gravel up to 20 mm size Cum 1122.00

16 EARTHWORK IN EXCAVATION/EMBANKMENT AND PROTECTION WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

32 Dry boulder filling in required profile with filling of voids etc. complete Cum 1286.00
including all lead & lifts, and well finished surface
33 Supplying and laying quarry spalls properly graded but not more than Cum 815.00
10cm in size with spreading in required profile including all leads & lifts
34 Labour charges for spreading of morrum or kanker on embankment etc.
with initial lead upto 50m lift upto 1.50m for
5cm to 18cm depth Cum 265.00
35 Supplying stone, spall and laying R. R. stone pitching, hammer dressed
with packing of voids from small stones including all lead & lifts, in
required profile of
(a) 45 cm thickness in two layers (± 5 % thickness tolerance) Cum 2160.00
(b) 30 cm thickness (± 5 % thickness tolerance) Cum 2058.00
(c) 23 cm thickness (± 5 % thickness tolerance) Cum 1820.00
36 Supplying stone, spall and laying Rip rap in required profile properly
hand packed using stone of specified size including all lead & lifts
(a) 23 cm thickness (± 5 % thickness tolerance) Cum 1712.00
(b) 30 cm thickness (± 5 % thickness tolerance) Cum 1794.00
(c) Only labour charges for laying of rip rap stone in required profile / Cum 520.00
thickness and hand packed properly using stones already available at site,
including all lead and lift.
37 (a) Supplying of rock fragment of specified sizes & propositions and laying Cum 1132.00
dumped rip rap in required profile including cost of excavation with all
lifts and lead up to ½ km (average thickness of rip rap 50 cms or more)
(b) Deduct from item no 36 (a) if only laying is to be done Cum 962.00
(c) Extra charges over item no. 36 a, 36 b for subsequent lead above 1/2 km as per item no. 10 c of
38 Protection Geotextile Non-woven : 400 GSM (NG2) part
/SqmA of this 95.00
chapter
Supply of Protection Geotextile made up of 100% virgin Polypropylerne
staple Fibres with needle punching process, having Mass per unit area
400 g/sqm as per ENISO 9864, CBR Puncture Strength of 4000 N as per
ENISO 12236, wide width tensile mass per unit area 26.5/32 KN/m as
per ENISO 10319, wide width elongation at break strength (MD/CD)
50/50% as per ENISO10319, dynamic performance resistance cone drop
10mm as per ENISO 13433, permittivity/flow rate 20 10-3m/s as per
ENISO 11058 and apparent opening size (AOS) 0.075mm as per ENISO
12956, UV Resistance @ 500 Hours > 70% as per relevant ENISO
standards complete at site.
Test of Non woven Geotextile NG 2 shall be done as per specification of
ENISO standards from independent approved lab.
39 Geotextile Layer for Filtration: 250 GSM (NG1) /Sqm 60.00
Supply of Filtration Geotextile made up of 100% virgin Polypropylerne
staple Fibres with needle punching process, having Mass per unit area
250 g/sqm as per EN ISO 9864, CBR Puncture Strength of 2300 N as
per EN ISO 12236, wide width tensile mass per unit area KN/m as per
ENISO 10319 15.8/18.5, wide with elongation at break strength
(MD/CD) 50/50% as per ENISO 10319 UV Resistance @ 500 Hours >
70% as per ENISO, Apparent Opening Size 0.075 mm as per ENISO
12956 & Water Flow Rate 35 l0-3 m /s as per ENISO11058, dynamic
performance resistance-cone drop 22mm as per ENISO 13433 complete
at site. Test of Nonwoven Geotextile NG 1 shall be done as per
specification of ENISO standards from independent approved lab.

17 EARTHWORK IN EXCAVATION/EMBANKMENT AND PROTECTION WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

40 Geotextile Layer for Filtration: 100-125 GSM (NG3) /Sqm 30.00

Supply of Protection Geotextile made up of 100% virgin Polypropylerne
staple Fibres with needle punching process, having Mass per unit area
100-125 g/sqm as per ENISO 9864, CBR Puncture Strength (CBR)of
1000 N as per ENISO 12236, wide width tensile mass per unit area 6/7.5
KN/m as per ENISO 10319, dynamic performance resistance cone drop
335 mm as per ENISO 13433, and UV Resistance @ 500 Hours > 70%
as per relevant ENISO standards complete at site.
Test of Non woven Geotextile NG 3 shall be done as per specification of
ENISO standards from independent approved lab.

41 750micron thick HDPE Geomembrane as water proofing layer: /Sqm 165.00

750 micron thick HDPE Geomembrane textured (Both side) as
waterproofing layer: Supply of HDPE liner 1 mm thickness manufactured
as per GRI GM 13 standards complete at site. Testing of HDPE Geo
membrane should be done as per specifications of GRIGM 13 from
independent approved lab.

42 1mm thick HDPE Geomembrane as waterproofing layer: /Sqm 220.00

1mm thick HDPE Geomembrane textured (Both side) as waterproofing
layer: Supply of HDPE liner 1 mm thickness manufactured as per GRI
GM 13 standards complete at site. Testing of HDPE Geo membrane
should be done as per specifications of GRIGM 13 from independent
approved lab.
43 1.5 mm thick HDPE Geomembrane as waterproofing layer: /Sqm 330.00
1.5 mm thick HDPE Geomembrane textured (Both side) as waterproofing
layer: Supply of HDPE liner 1 mm thickness manufactured as per GRI
GM 13 standards complete at site. Testing of HDPE Geo membrane
should be done as per specifications of GRIGM 13 from independent
approved lab.
44 2.0 mm thick HDPE Geomembrane as waterproofing layer: /Sqm 420.00
2.0 mm thick HDPE Geomembrane textured (Both side) as waterproofing
layer: Supply of HDPE liner 1 mm thickness manufactured as per GRI
GM 13 standards complete at site. Testing of HDPE Geo membrane
should be done as per specifications of GRIGM 13 from independent
approved lab.
45 Laying, welding & testing of 1mm HDPE Liner /Sqm 18.00
46 Laying & Stitching of 400 GSM protection Geotextile /Sqm 8.00
47 Laying & Stitching of filter geotextile 250 GSM /Sqm 8.00
48 Laying & Stitching of Protection geotextile 125 GSM /Sqm 8.00

PART – D QUARRY RUBBISH / SPALL :-

49 Spreading of quarry rubbish / spalls / murranda to required grade & / cum 38.00
camber in layers not exceeding 15 cm. thickness (loose) as per
specifications including dressing etc. complete.
50 Supplying, Laying & consolidation of quarry rubbish / Murrum / Murda / cum 584.00
to required grade & camber in layers not exceeding 15 cm. thickness
(loose) by road roller as per specifications including dressing etc.
PART – Ecomplete.
CONSTRUCTION OF WATER COURSE :-
51 Survey and rehabilitation work of existing water course including jungle Per KM 37473.64
clearance, cutting and uprooting of trees. Earth work in excavation /
embankment for restoration of sector, clearance of silt dressing and
manual compaction of earth work etc. complete in all respect.

18 EARTHWORK IN EXCAVATION/EMBANKMENT AND PROTECTION WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

52 Construction of single nakka as per drawing and specifications shown in Each 3857.00
typical drawing using PCC (1:3:6) M-10, A20, in foundation below
Nakka wall & random rubble masonry in cement sand mortar 1:6 having
plaster 20mm thick and 50mm thick cement concrete (1:2:4) coping in M-
15, A-20. Supplying and fixing of Nakka gate with two frames and one
shutter complete in all respect.

53 Construction of Double nakka as per drawing and specifications shown in Each 4307.00
typical drawing using PCC (1:3:6) M-10, A20, in foundation below
Nakka wall & random rubble masonry in cement sand mortar 1:6 having
plaster 20mm thick and 50mm thick cement concrete (1:2:4) coping in M-
15, A-20. Supplying and fixing of Nakka gate with four frames and one
shutter complete in all respect.

54 Construction of CD works as per drawing and specifications shown in Each 16079.00

typical drawing using PCC (1:3:6) M-10-A-20, in foundation below walls
& WC bed , random rubble masonry in cement sand mortar 1:6 having
plaster 20mm thick in cement sand mortar 1:3 on wall and cement
concrete (1:2:4) M-15,A-20 50mm thick and providing laying & fixing in
position RCC spun or Hume pipe 450mm NP-2.

19 EARTHWORK IN EXCAVATION/EMBANKMENT AND PROTECTION WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER VI

MORTAR

NOTES:
1 These rates are at work site exclusive of all taxes, GST, Contractor's profit, overheads &
royalty etc. unless otherwise specified.

2 The rates given below are complete rates and include all leads of the construction material.

3 Rates are inclusive of cost of water, grinding, mixing of mortar by mechanical mixer and
required T&P unless other wise mentioned.

4 For only petty works mannual mixing of the mortar will be allowed, Petty work is defined
where total mortar consumption in a single work order is note more then 5 cum.

5 The proportions of various ingredients in the item are by volume batching.

S. Rate in
Item Unit
No. Rs.

1 Cement mortar 1 : 6 including all leads of all construction materials. (1

Cement and 6 sand) Cum 3096.00

2 Cement mortar 1 : 5 (1 Cement and 5 sand) including all leads of all

Cum 3363.00
construction materials.
3 Cement mortar 1 : 4 (1 Cement and 4 sand) including all leads of all
Cum 3737.00
construction materials.
4 Cement mortar 1 : 3 (1 Cement and 3 sand) including all leads of all
Cum 4385.00
construction materials.
5 Cement mortar 1 : 2 (1 Cement and 2 sand) including all leads of all
Cum 5232.00
construction materials.
6 Add extra over item No. 1 to 5 in case weigh batching is adopted Cum 79.00
7 Mud mortar including all leads of all construction materials. Cum 515.00

20 MORTAR
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER VII

MASONRY
NOTES
1 These rates are at work site inclusive of all taxes, GST, Contractor's profit, overheads
& royalty etc. unless otherwise specified.
2 All rates in this chapter are inclusive of de-watering wherever required.
3 These rates include lifts up to 5 meters from ground level upward & downward.
4 The labour rates are inclusive of laying, mixing of mortar by mechanical mixer, all T
& P, scaffolding, curing and water charges etc.
5 Masonry work will be considered as superstructure, for different structures as under :
(i) Canal :- The masonry executed above designed canal bed level.
(ii) Dam weir, wing wall and C.D. works etc.
The masonry above apron level and or from the level where the batter starts.
6 One full bag of cement is 50 kg by weight and 0.03481 cum by volume (standard).
7 In works involving coursed masonry, thickness of 0.30 m per coursed face shall only
be payable as coursed masonry and the rest will be paid as R. R. masonry. The rate is
inclusive of chisel dressing on all the four faces of stones.
S. No. Item Unit Rate in Rs
PART A : RANDOM RUBBLE, COURSED / KHARANJA
1 Random rubble stone masonry (using R. R. stones where 75 %
stones to be not less than 15 cm in size in any direction and
weighing not less than 23 kg.) for foundation including curing
with all leads of all construction materials including curing etc.
complete.
(a) In cement sand mortar 1:3 Cum 4944.00
(b) In cement sand mortar 1:4 Cum 4580.00
(c) In cement sand mortar 1:5 Cum 4377.00
(d) In cement sand mortar 1:6 Cum 4243.00
(e) In cement sand mortar 1:8 Cum 4080.00
2 R.R. stone Masonry Kharanja with proper packing of chipping
stones using hammer as per IS specification (using R. R. stones
where 75 % stones to be not less than 15 cm in size in any
direction and weighing not less than 23 kg.) for foundation Cum 4315.00
including all leads of all construction materials, curing etc.
complete in 1: 6 Cement Mortar
Coursed stone Kharanja masonry (using hammer dressed stones
not less than 20 cm in any direction and at least 50 % stones to
be more than 23 cm in depth) up to 0.5 thickness on top of
exposed face, including all leads of all construction materials
including curing etc. complete.
(a) In cement sand mortar 1:3 Cum 7485.00
(b) In cement sand mortar 1:4 Cum 7221.00
(c) In cement sand mortar 1:5 Cum 7043.00
(d) In cement sand mortar 1:6 Cum 6915.00
(e) In cement sand mortar 1:8 Cum 6773.00
4 R. R. stone masonry in mud mortar including all leads of all Cum 2411.00
construction materials.

21 MASONRY
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

5 Dry stone masonry including all leads of all construction Cum 1718.00
materials.
6 R. R. stone masonry (where 90 % stones weighing not less than
37.5 kg and no dimension to be less than 23 cm.) for foundation
including all leads of all construction materials including curing
etc. complete.
(a) In cement sand mortar 1:3 Cum 5273.00
(b) In cement sand mortar 1:4 Cum 4917.00
(c) In cement sand mortar 1:5 Cum 4717.00
(d) In cement sand mortar 1:6 Cum 4572.00
7 Coursed stone masonry (using C.R. stone for face work duly
hammer dressed on beds and all sides, the bed joints and faces
chisel dressed for at least 8 cm back from face and at least 4 cm
from sides, height not less than 25 cm and weighing not less
than 50 kg, 50 % stones to have depth more than 45 cm and tail
area not less than half the face area) for foundation (up to 0.5 m
thickness) including all leads of all construction materials
including curing etc. complete.
(a) In cement sand mortar 1:3 Cum 6655.00
(b) In cement sand mortar 1:4 Cum 6346.00
(c) In cement sand mortar 1:5 Cum 6169.00
8 Add extra over item no. 1 to 7 for
(a) Masonry work in superstructure Cum 212.00
(b) Thickness of wall upto 30 cm or less Cum 186.00

(c) Each subsequent height of 3.0 metre or part there-of above

initial lift of 5.0 m from ground level (up ward and down ward) Cum 308.00
for dam work under item no 6& 7.
(d) Each subsequent height of 3.0 metre or part thereof above Cum 215.00
initial lift of 5.0 m from ground level (up ward and down ward)
for item other than 6 & 7.
PART B : ARCH MASONRY:
9 Coursed stone Arch masonry (Using C.R. stones hammer
dressed & size not less tham 20 cm x 20cm x 30cm) including
all leads of all construction materials including curing etc.
(a) complete.
In cement sand mortar 1:3 Cum 10885.00
(b) In cement sand mortar 1:4 Cum 10559.00
(c) In cement sand mortar 1:5 Cum 10372.00
(d) In cement sand mortar 1:6 Cum 10237.00
PART C : BRICK MASONRY:
10 Brick masonry (using well burnt clay bricks of size 230 x 110
x 70 mm, class designation 75 as per specification) up to plinth
including all leads of all construction materials including curing
etc. complete.
(a) In cement sand mortar 1:3 Cum 6114.00
(b) In cement sand mortar 1:4 Cum 5894.00
(c) In cement sand mortar 1:5 Cum 5767.00
(d) In cement sand mortar 1:6 Cum 5676.00

22 MASONRY
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

11 Half Brick masonry (using well burnt clay bricks of size 230 x
110 x 70 mm, class designation 75 as per specification) for
partition wall including all leads of all construction materials
including curing etc. complete.
(a) In cement sand mortar 1:3 Sqm 741.00
(b) In cement sand mortar 1:4 Sqm 724.00
12 Brick masonry on edge (using well burnt clay bricks of size 230
x 110 x 70 mm, class designation 75 as per specification) for
partition wall including all leads of all construction materials
including curing etc. complete.
(a) In cement sand mortar 1:3 Sqm 622.00
(b) In cement sand mortar 1:4 Sqm 605.00
13 Add extra for superstructure brick masonry on item no 10 Cum 212.00
14 Add extra if well burnt clay bricks (size 230x110x70 mm) class
designation 100 as per specifications are to be used
(a) Over Item No. 10 Cum 490.36
(b) Over Item No. 11 Sqm 50.73
(c) Over Item No.12 Sqm 33.82
15 Deduct if common burnt clay bricks (size 230x110x70 mm)
class designation 50 as per specifications are to be used are to
be used.
(a) Over Item No. 10 Cum 274.18
(b) Over Item No. 11 Sqm 28.36
(c) Over Item No.12 Sqm 18.91
16 Add extra for each subsequent height of 3.0 metre or part there
of above initial lift of 5.0 m from ground level (up ward and Cum 220.00
down ward) over item No 10

23 MASONRY
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER - VIII

PLASTERING AND POINTING

NOTES
1 The rates are for complete work including racking of joints, curing, grinding, mixing of
mortar by mechanical mixer, finishing, T&P, scaffolding and cost of material.
2 The rate covers protection of all places and things, requiring protection and cleaning of
all such places and things of all dropping and splashes of mortar etc.
3 These rates are at work site inclusive of all taxes, GST, Contractor's profit, overheads &
royalty etc. unless otherwise specified.
4 The rates in this chapter are inclusive of de-watering wherever required.
5 25 mm plaster ( 1:3 ) is to be used for only block joint for spillway work, 20 mm thick
plaster is to be used for RR Masonry and 12 mm thick plaster is to be used for brick
masonry
S. No. Item Unit Rate in Rs
CEMENT PLASTER
1 Plaster in cement sand mortar 1:3 including racking of joints, smooth
finishing & curing etc. complete including all leads of all
construction materials of thickness:
(a) 25 mm To be used only for spillway block joints Sqm
391.00
(b) 20 mm Sqm 335.00
(c) 12mm Sqm 251.00
(d) 6 mm Sqm 152.00
2 Plaster in cement sand mortar 1:4 including racking of joints, smooth
finishing & curing etc. complete including all leads of all
construction materials of thickness:
(a) 20 mm Sqm 314.00
(b) 12mm Sqm 238.00
3 Plaster in cement sand mortar 1:5 including racking of joints, smooth
finishing & curing etc. complete including all leads of all
construction materials of thickness:
(a) 20 mm Sqm 302.00
(b) 12mm Sqm 230.00
4 Plaster in cement sand mortar 1:6 including racking of joints, smooth
finishing & curing etc. complete including all leads of all
construction materials , of thickness:
(a) 20 mm Sqm 297.00
(b) 12mm Sqm 225.00
Add extra over item no 1 to 4 used for repair of plaster including 10% of
5 cutting the patch in a uniform shape, racking and preparing surface Sqm item rate
including all leads of all construction materials complete in all
respect.
Finishing with neat cement (punning) including cost of cement and 40.00
Sqm
all leads of all construction materials.
Add extra over item no 1 to 4 for plaster done over ceiling. 20% of item
7 rate

24 PLASTERING AND POINTING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

Add extra over item no 1 to 4 for plaster over spherical or groin 25% of item
8 ceiling. rate
9 Making grooves as per design in plaster 10 mm to 20 mm wide. metre. 10.00
10 Making lining out on plaster to imitate stone or concrete blocks Sqm 48.00
walling.
11 Add extra over item No. 1 to 4 for height from more than 5 m from 10% of item
base / floor level of structure / building for every additional height of rate
3.0 m or part thereof (upward & downward).
12 Add extra for plastering on circular work not exceeding 6 m in 10% of item
radius. rate
( c) POINTING
13 Flush or ruled pointing on stone masonry including racking of joints
and curing etc. complete including all leads of all construction
materials in mortar ratio.
(a) In Cement sand mortar 1:3 Sqm 149.00
(b) In Cement sand mortar 1:4 Sqm 145.00
14 Raised and cut pointing on stone masonry including racking of
joints and curing etc. complete including all leads of all construction
materials in mortar ratio.
(a) Cement sand mortar 1:3 Sqm 231.00
(b) Cement sand mortar 1:4 Sqm 226.00
15 Add extra over item No. 13 to 14 for height from more than 5 m 10% of item
from base / floor level of structure / building for every additional rate
height of 3.0 m or part there-of (upward & downward).

25 PLASTERING AND POINTING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER IX
CONCRETE & CANAL LINING
NOTES
1 These rates are at work site inclusive of all leads, all taxes, GST, Contractor's profit, overheads,
panchayat tax & royalty etc. unless otherwise specified.
2 These rates include lifts up to 5 meters from ground level upward and downward.
3 Rates for complete work including required material components, admixture, laying,
compaction, vibration, curing and all types of T & P including vibrator, P.O.L. etc and grinding
and mixing of mix/mortar.
4 The Concrete for all grade shall be produced in conformation to the laid down procedures and all
relevant clauses of IS 456 : 2000, IS 457 and other relevant IS code & practices.
5 Rates of concrete (Nominal mix or Design Mix) is assessed considering concrete produced /
manufactured by weigh batch hopper mechnical mixer with assigned capacity of mixing drum .
6 For Nominal mix concreting work, the coarse aggregates and fine aggregates can be measured by
the standard boxes and cement by bag. The boxes should be designed for 1/2 bag,1 bag etc. of
cement.
7 No R.C.C. work shall be permitted without the use of mechanical mixer by hopper and vibrator.

8 The rate for R.C.C. work is inclusive of cost of providing cement mortar covers blocks. The rates
for centering includes placement of cover blocks.
9 Use of nominal mix of concrete 1:2:4 & 1:1.5:3 is allowed only for petty works or with the
permission of Engineer incharge issued with proper justification for use of nominal mix.

10 For Part-A, rates are excluding the cost of centering, shuttering and form work required for
concreting. For Part-B (Canal Lining), rates are inclusive of cost of centering, shuttering and
form work required for concreting.

11 The rates in this chapter are inclusive of de-watering wherever required.

12 Proportion of ingredients in concrete will be governed by mix design. If the Cement consumption
for the approved Concrete mix design is lower than cement content shown in respective BSR
item, than deduction from rate of concrete will be made @ Rs 6.30 per Kg for lesser requirment
of cement per cum of concrete. But no extra payment shall be paid if cement consumption is
higher than cement content shown in respective item. Cement consumption in Mix design is to
be in coherance of latest revision of IS-456 code.

13 Use of fly ash shall be permitted with permission of Superintending Engineer for design mix
only when OPC cement is being used. Fly ash qulaity and quantity to be used should conform IS
code 3812-1981 part-I and fineness as per IS code 269-1989. No extra labour charges for mixing
of fly ash shall be admissible.

14 Add extra with the permission of Superintending Engineer,

1. Rs 260.00 per cum of concrete if computerised password protected composite weight-batching
and mixing plant with suitable green concrete transportation mechanism or transit mixer is used
2. Rs 175.00 per cum of concrete if computerised mobile transit mixer (i.e Fiori) is used.
3. Rs 100.00 per cum including Hire charges of pump, piping work & accessories etc. if
concrete is to be placed by the pump.

26 CONCRETE CANAL LINING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

PART A : CONCRETE WORK

S. No. Item Unit Rate in Rs
1 Providing and Laying in position of Cement concrete Design mix M-
15 including leads of all construction materials, plasticizers (if
required), curing, compaction and finishing with rendering in cement
sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints
excluding the cost of centering, shuttering and reinforcement. Well
graded crusher broken stone aggregate of maximum size upto;
(For mix design Cement content considered 320 kg/ cum of
concrete)

(a) 150 mm Cum 5463.00

(b) 80 mm Cum 5573.00
(c) 40 mm Cum 5723.00
(d) 20 mm Cum 5775.00
2 Providing and Laying in position of Cement concrete Design mix M-
20 including leads of all construction materials, plasticizers (if
required), curing, compaction and finishing with rendering in cement
sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints
excluding the cost of centering, shuttering and reinforcement. Well
graded crusher broken stone aggregate of maximum size upto;
(For mix design Cement content considered 400 kg/ cum of
concrete)
(a) 150 mm Cum 6028.00
(b) 80 mm Cum 6138.00
(c) 40 mm Cum 6288.00
(d) 20 mm Cum 6340.00
3 Providing and Laying in position of Cement concrete Design mix M-
25 including leads of all construction materials, plasticizers (if
required), curing, compaction and finishing with rendering in cement
sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints
excluding the cost of centering, shuttering and reinforcement. Well
graded crusher broken stone aggregate of maximum size upto;
(For mix design Cement content considered 420 kg/ cum of
concrete)
(a) 150 mm Cum 6288.00
(b) 80 mm Cum 6398.00
(c) 40 mm Cum 6548.00
(d) 20 mm Cum 6600.00
4 Providing and Laying in position of Cement concrete Design mix M-
30 including leads of all construction materials, plasticizers (if
required), curing, compaction and finishing with rendering in cement
sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints
excluding the cost of centering, shuttering and reinforcement. Well
graded crusher broken stone aggregate of maximum size upto;
(For mix design Cement content considered 428 kg/ cum of
concrete)
(a) 150 mm Cum 6319.00
(b) 80 mm Cum 6429.00
(c) 40 mm Cum 6579.00
(d) 20 mm Cum 6631.00

27 CONCRETE CANAL LINING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

5 Providing and Laying in position of Cement concrete Design mix M-

35 including leads of all construction materials, plasticizers (if
required), curing, compaction and finishing with rendering in cement
sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints
excluding the cost of centering, shuttering and reinforcement. Well
graded crusher broken stone aggregate of maximum size upto;
(For mix design Cement content considered 435 kg/ cum of
concrete)
(a) 150 mm Cum 6400.00
(b) 80 mm Cum 6510.00
(c) 40 mm Cum 6660.00
(d) 20 mm Cum 6712.00
6 Providing and Laying in position of Cement concrete Nominal mix
(1:1.5:3) including leads of all construction materials, curing,
compaction and finishing with rendering in cement sand mortar 1:3 (1
cement : 3 coarse sand) and making good the joints excluding the cost
of centering, shuttering and reinforcement. Well graded crusher
broken stone aggregate of maximum size upto;

(a) 150 mm Cum 5818.00

(b) 80 mm Cum 5927.00
(c) 40 mm Cum 6091.00
(d) 20 mm Cum 6145.00
7 Providing and Laying in position of Cement concrete Nominal mix
(1:2:4) including leads of all construction materials, curing,
compaction and finishing with rendering in cement sand mortar 1:3 (1
cement : 3 coarse sand) and making good the joints excluding the cost
of centering, shuttering and reinforcement. Well graded crusher
broken stone aggregate of maximum size upto;
(a) 150 mm Cum 5375.00
(b) 80 mm Cum 5484.00
(c) 40 mm Cum 5648.00
(d) 20 mm Cum 5703.00
8 Providing and Laying in position of Cement concrete Nominal mix
(1:3:6) including leads of all construction materials, curing,
compaction and finishing with rendering in cement sand mortar 1:3 (1
cement : 3 coarse sand) and making good the joints excluding the cost
of centering, shuttering and reinforcement. Well graded crusher
broken stone aggregate of maximum size upto;
(a) 150 mm Cum 4808.00
(b) 80 mm Cum 4922.00
(c) 40 mm Cum 5092.00
(d) 20 mm Cum 5150.00
9 Providing and Laying in position of Cement concrete Nominal mix
(1:4:8) including leads of all construction materials, curing,
compaction and finishing with rendering in cement sand mortar 1:3 (1
cement : 3 coarse sand) and making good the joints excluding the cost
of centering, shuttering and reinforcement. Well graded crusher
broken stone aggregate of maximum size upto;
(a) 150 mm Cum 4424.00
(b) 80 mm Cum 4538.00
(c) 40 mm Cum 4709.00
(d) 20 mm Cum 4766.00

28 CONCRETE CANAL LINING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

10 Providing and Laying in position of Cement concrete Nominal mix

(1:5:10) including leads of all construction materials, curing,
compaction and finishing with rendering in cement sand mortar 1:3
(1 cement : 3 coarse sand) and making good the joints excluding the
cost of centering, shuttering and reinforcement. Well graded crusher
broken stone aggregate of maximum size upto;
(a) 150 mm Cum 4222.00
(b) 80 mm Cum 4336.00
(c) 40 mm Cum 4507.00
(d) 20 mm Cum 4564.00
11 Nominal mix of Plain Cement Concrete well mixed and laid in position
using 20% max permissible limit of plums above 160 mm and up to
450mm, including curing and finishing etc including all leads of all
construction materials complete in all respect with well graded crusher
broken stone aggregate. The plums shall be distributed evenly and shall
be not closer than 150 mm from the surface.
11.1 PCC Nominal Mix 1:2:4 with plum,
(a) Max size of Aggregate 80 mm, Cum 5089.00
(b) Max size of Aggregate 40 mm, Cum 5224.00
(c) Max size of Aggregate 20 mm Cum 5269.00
11.2 PCC Nominal Mix 1:3:6 with plum,
(a) Max size of Aggregate 80 mm, Cum 4602.00
(b) Max size of Aggregate 40 mm Cum 4743.00
(c) Max size of Aggregate 20 mm Cum 4790.00
11.3 PCC Nominal Mix 1:4:8 with plum,
(a) Max size of Aggregate 80 mm Cum 4277.00
(b) Max size of Aggregate 40 mm, Cum 4418.00
(c) Max size of Aggregate 20 mm, Cum 4465.00
11.4 PCC Nominal Mix 1:5:10 plum,
(a) Max size of Aggregate 80 mm, Cum 4102.00
(b) Max size of Aggregate 40 mm, Cum 4240.00
(c) Max size of Aggregate 20 mm, Cum 4287.00
12 Add extra over labour rates for item No. 2 to 5 for II stage concrete for
obstruction of II stage embedded parts & restricted working space.
(a) In Vertical/ radial block-outs Cum 810.6
(b) In horizontal block-outs Cum 507
13 Add extra over item No. 1 to 7
(a) For each subsequent height of 3.0 meter or part thereof above initial lift Cum
160.00
of 5.0 m from ground level. (upward and downward)
(b) Add Extra for RCC work for Retaining wall, wing wall, returns, divide Cum 190.00
wall, Pier.
(c) Add Extra for RCC work for Bed Plate, Girder, Slab etc in suspended Cum 175.00
form
(d) Add Extra for RCC work for sluice well, intake, pump house, Arch, Cum 225.00
Ogee
(e) Add Extra for RCC work for tunneling, chute block, basin block, end Cum 260.00
sill, dented end sill etc
(f) Extra labour charges if concreting is done on water retaining structures Cum 200.00

29 CONCRETE CANAL LINING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

PART B : CANAL LINING

14 Preparation and dressing the sub grade including removal of
irregularities up to 7.5 cm in soil, morrum mixed with pebbles, small
boulders and kankar & murrum for
(a) Bed Sqm 9.90
(b) Side slopes Sqm 13.30
15 Preparation and dressing the sub grade including removal of
irregularities up to 7.5 cm in soft rock & similar type of strata for
(a) Bed Sqm 14.40
(b) Side slopes Sqm 18.60
16 Cement concrete lining of nominal mix (1:3:6) with, upto 20 mm size
well graded crusher broken stone aggregate laid as per specifications
including all leads of all construction materials including rendering,
compaction and curing etc. complete for canal bed of thickness.
(a) 10 cm Sqm 620.00
(b) 7.5 cm Sqm 477.00
17 Cement concrete lining of nominal mix (1:3:6) with upto 20 mm size Sqm
well graded crusher broken stone aggregate laid as per specifications
including all leads of all construction materials including rendering
and curing etc. complete for canal side lining of thickness.
(a) 10 cm Sqm 713.40
(b) 7.5 cm Sqm 564.40
18 Providing and laying cast in situ plain cement concrete design mix M-
15 grade for lining, using well graded crusher broken aggregate of
maximum nominal size 20 mm conforming to IS:383-1970, including
proportioning of the ingredients by weigh batching and mixing by
mechanical mixer including finishing of concrete lining, cutting of
grooves for construction joints, complete as per specification with all
leads and lifts of construction material complete for canal bed of
thickness.

(a) 10 cm Sqm 692.00

(b) 7.5 cm Sqm 532.00
19 Providing and laying cast in situ plain cement concrete design mix M-
15 grade for lining, using well graded crusher broken aggregate of
maximum nominal size 20 mm conforming to IS-383-1970, including
proportioning of the ingredients by weigh batching and mixing by
mechanical mixer including finishing of concrete lining, cutting of
grooves for construction joints, complete as per specification with all
leads and lifts of construction material complete for canal side of
thickness.

(a) 10 cm Sqm 765.00

(b) 7.5 cm Sqm 602.00
20 Add extra over item no 16 to 19 for lining done by paver as per Sqm 96
specifications complete
21 Add extra over item no 16 to 19 for placement of cement concrete Sqm 47
lining with acrow type (or equivalent) steel slip form gantry.
22 Add extra over item no 16 to 19 if super sulphate Cement is to be used
for lining of canal Bed & Sides
(a) 100 mm thick CC lining Sqm 50.00
(b) 75 mm thick CC lining Sqm 37.00

30 CONCRETE CANAL LINING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

23 Add Extra over item no 16 to 19 if two coat of water based chemical Sqm 30.00
curing is used for sides of canal lining
24 Canal lining with hydraulic compressed pre-cast cement concrete M15
tiles of size 300 x 300 x 40 mm laid over 12 mm (av.) thick subgrade
cement plaster in CM (1:6) , 12 mm thick sandwich plaster in CM 1:5
and 6 mm thick jointing mortar in cement mortar (1:3) etc. including
curing and all leads& lift of all construction materials complete in all
respect

(a) In bed. Sqm 697.00

(b) In sides Sqm 733.00
25 Canal lining with hydraulic compressed pre-cast slab of cement
concrete M15 tiles of size 300 x 150 x 40 mm laid over 12 mm (av.)
thick subgrade cement plaster in CM (1:6) , 12 mm thick jointing
sandwich plaster in CM 1:5 and 6 mm thick jointing mortar in cement
mortar (1:3) etc. including curing and all leads& lift of all
construction materials complete in all respect
(a) In bed. Sqm 780.00
(b) In sides Sqm 816.00
26 Providing and laying canal lining with mechanically vibrated 300 x
300 x 50 mm PCC blocks made from concrete mix 1:2:4, A20
including all leads and lifts of material, curing, stacking, loading,
unloading & transportation of blocks from manufacturing site to lining
site. Single tile lining consisting of 12 mm thick cement mortar (1:6)
plaster on sub-grade, 12 mm thick sandwich plaster in cement mortar
(1:5) over sub grade & 50 mm thick tile lining in cement mortar (1:3)
laid over 6 mm thick mortar layer in cement mortar (1:3) & jointing
mortar 1:3 including curing, all leads of all construction materials and
machinery charges with mixture vibration etc., complete as per
technical specifications
(a) In bed Sqm 756.00
(b) In sides Sqm 794.00
27 Providing and laying canal lining with mechanically vibrated 300 x
150 x 50 mm PCC blocks made from concrete mix 1:2:4, A20
including all leads and lifts of material, curing, stacking, loading,
unloading & transportation of blocks from manufacturing site to lining
site. Single tile lining consisting of 12 mm thick cement mortar (1:6)
plaster on sub-grade, 12 mm thick sandwich plaster in cement mortar
(1:5) over sub grade & 50 mm thick tile lining in cement mortar (1:3)
laid over 6 mm thick mortar layer in cement mortar (1:3) including
curing, all leads of all construction materials, curing charges and
machinery charges with mixture vibration etc., complete as per
technical specifications.
(a) In bed Sqm 830.00
(b) In sides Sqm 857.00
28 Providing and laying double tile canal lining with mechanically
vibrated 300 x 300 x 50 mm PCC blocks made from concrete mix
1:2:4, A20 including all leads and lifts of material, curing, stacking,
loading, unloading & transportation of blocks from manufacturing site
to lining site.
First layer of 50 mm thick PCC tile to be laid in 6mm thick jointing
cement mortar (1:5) and side jointing cement mortar 1:3 over 10 mm
thick cement mortar (1:6) . Second layer of PCC blocks is to be laid in
CM 1:3 over 16 mm sandwitch plaster in CM (1:4) and over that 6 mm
thick cement jointing mortar 1:3 (Bottom & side ) including curing,
all leads of all construction materials complete as per specifications.

(a) In bed Sqm 1214.00

(b) In sides Sqm 1269.00

31 CONCRETE CANAL LINING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

29 Providing and laying double tile canal lining with mechanically

vibrated 300 x 150 x 50 mm PCC blocks made from concrete mix
1:2:4, A20 including all leads and lifts of material, curing, stacking,
loading, unloading & transportation of blocks from manufacturing site
to lining site.
First layer of 50 mm thick PCC tile to be laid in 6mm thick jointing
cement mortar (1:5) and side jointing cement mortar 1:3 over 10 mm
thick cement mortar (1:6) . Second layer of PCC blocks is to be laid in
CM 1:3 over 16 mm sandwitch plaster in CM (1:4) and over that 6 mm
thick cement jointing mortar 1:3 (Bottom & side ) including curing,
all leads of all construction materials complete as per specifications.

(a) In bed Sqm 1266.00

(b) In sides Sqm 1447.00
30 Brick masonry lining consisting of 12 mm thick plaster in cement
mortar (1:6) on sub grade, 16 mm thick sandwich plaster in cement
mortar (1:3) over base plaster & 70 mm thick brick masonry in cement
mortar (1:3) laid over 6 mm thick mortar layer in cement mortar (1:3)
including curing etc. including all leads of construction materials
complete as per specifications.

(a) In bed 10 Sqm 3727.00

(b) In sides 10 Sqm 3929.00
31 P&F precast dense cement concrete (vibro pressed) drains section
block of different size as per approved drawing and design and strength
as per IS Code 2185-1979 part – I of grade "D" (5mm2) proper quality
of additive/ admixture like plasticizer etc added to produce high
quality and durable drain section blocks of required shape as per
approved design and drawing complete with fixing and joining in
cement mortar 1:4 in proper grade and level complete in all respect
including dressing of earth work and disposal of surplus earth within
0.5 Km lead .

(a) 40 mm thick Sqm 835.00

(b) up to 60 mm thick Sqm 1008.00
(c) up to 80 mm thick Sqm 1229.00
32 Providing and laying cast in situ concrete sleepers 15 cm x 7.5 cm in
bed in cement concrete (1:3:6) with maximum size of crusher broken
stone aggregate upto 20 mm well graded including all leads of all
construction materials including curing, finishing & form work etc.
complete as per specification for:
(a) In bed RM 62.00
(b) In sides RM 67.00
33 A Filling of construction joints with Bitumen based sealing compound,
including painting the concrete sleepers below lining and sides of
lining panel as per specification provided in IS: 3384-1986 and all RM 68.00
leads of all construction materials including cost of sealing compound,
complete in all respect.
B Filling of construction joints with Bitumen based sealing compound
lining in the grove as per IS made by cutter upto the 1/3 depth of
concrete lining as per specification provided in IS: 3384-1986 and all RM 89.00
leads of all construction materials including cost of sealing compound,
complete in all respect.

32 CONCRETE CANAL LINING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

34 Extra charges for water spray by nozzle on sub grade of canal

Sqm 2.50
including bed and side slopes before laying plain concrete for lining
35 work.
Providing and laying under drainage below canal lining consisting of
porous concrete of mix ratio 1:4 (1 cement: 4 course aggregate) 75 mm
diametre, 300 mm long supported by 75 mm thick layer of coarse Each 150.00
aggregate 12.5 mm to 40 mm size and 50 mm thick layer of sand.
36 Providing and laying 75mm thick sand layer in bed (over clays sub
grade) duly stabilized with cement slurry (1:20) including all leads and Sqm 191.00
lift of material.
37 Providing and laying 75mm thick sand layer on side slope (over clays
sub grade) duly stabilized with cement slurry (1:10) including all leads Sqm 233.00
and lift of material.
38 (a) Providing and laying CNS (Cohesive non swelling) seclected soil
(from any source including private fileds) and laying in layers below
PCC block / CC lining in layers of 15-20 cm watering and compaction
to achieve a density of 95 % of standard proctor's density including all Cum 302.00
lead & lift, dewatering whenever necessary and complete as per
technical specifications.Thickness of and specification of CNS should
confirm to IS:9451 latest revision.

39 Supplying, laying & spreading of LDPE film of 250 micron on bed

and sides including jointing etc. complete as per specifications
including cost of LDPE film, overlapping, adhesive tape etc. with Sqm 59.00
transportation charges upto work site complete.
40 Supply, laying and fixing of G.I. Chain link wire mesh of 10cm x
10cm of 12 gauge for concrete work/ concrete lining work in canal,
including cutting, stepples required for fixing wire mesh strips, placing Sqm 128
in position complete in all respect as per drawing, specification and as
per direction of Engineer-in-charge
41 Supply, laying and fixing of G.I. Chain link wire mesh of 10cm x
10cm of 10 gauge for concrete work/ concrete lining work in canal,
including cutting, stepples required for fixing wire mesh strips, placing Sqm 148
in position complete in all respect as per drawing, specification and as
per direction of Engineer-in-charge
42 Supply, laying and fixing of G.I. Chain link wire mesh of 10cm x
10cm of 8 gauge for concrete work/ concrete lining work in canal,
including cutting, stepples required for fixing wire mesh strips, placing Sqm 168
in position complete in all respect as per drawing, specification and as
per direction of Engineer-in-charge

33 CONCRETE CANAL LINING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER -X

CENTERING, SHUTTERING AND R.C.C.

NOTES
1 The following rates are inclusive of all taxes, levies, Contractor's profit & royalty etc.
2 False work / centering and shuttering should confirm to IS 14687 and Steel sheet plates
conforming to IS 2062 or IS 8500 or IS 1977 may be used for form and form lining and rolled
sections and tubes conforming to IS 2062 or IS 8500 or IS 1161 may be used for steel forming and
bracings.
3 Steel shuttering plates should be structuraly strong, rigid and having good finish, it should not
defelect for designed load.
4 The rates are for complete items including all leads & lifts of material except otherwise stated.
5 Add extra over basic rate of concrete (to be used for RCC) as per item No.10 to meet additional
expenses on account of obstructions in laying and placing of concrete due to reinforcement.
6 The rates for centering and shuttering are for steel/ plywood shuttering for complete work
including, centering shuttering, nails, nut bolts and other such items required to prevent bulging or
leaking of concrete etc.
7 The shuttering shall be removed after required time as per instructions of Engineer- In- Charge and
IS: 456
8 The rates are inclusive of providing plastic or cement mortar cover blocks for reinforcement and
placing thereof at appropriate places properly.
9 No deduction shall be made for weep holes, grout pipes etc. wherever required to be left in C.C.
and no payment on accounts of extra labour shall be made for leaving such pipes or holes.
10 Necessary arrangements for even and safe load distrtibution to ground level and rigidness of props
are inlcusive in the rates for centering and shuttering.
11 For details of Finishes F1,F2, F3, & F4 please refer Annexure XI.
12 The rates in this chapter are inclusive of de-watering wherever required.

S.No. Item Unit Rate in Rs

1 Side shuttering including propping etc. complete (to achieve finish F 2
for :
(a) Block joints of foundation stilling basins buckets, aprons etc. (non -
Sqm 160.00
suspended horizontally laid mass concrete)
(b) Top or intermediate bed plates, in between masonry or piers,
Sqm 185.00
abutments sluice wells etc.
(c) Retaining wall, counterfort, abutment, wing walls up stream or down-
Sqm 220.00
stream slope facings of dams and open faces of construction joints etc.
(d) Curved edges or sides of special shapes like baffle or chute blocks, end
sills, Basin Block, projected copings, extended sills, curved surfaces Sqm 340.00
arches, circular ducts etc.
2 Centering and shuttering for slabs, beams, lintels Columns, trough with
or without caps and base including propping and removing Sqm 225.00

3 Centering and shuttering for piers, galleries, barrels, intake well, sluice
Sqm 340.00
well upto 3.0m height from base/floor level (To achieve F2 finish)

34 CENTERING, SHUTTERING AND RCC

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

4 Add extra over item No. 1 c , 1d, 2 and 3 for centering and shutterring
for each additional 1 m height or part thereof above initial height of Sqm 25.00
3.0m from base/floor level.
5 Centering and shuttering for 2nd stage concrete for F2 finish)
(a) For vertical blocks outs
Sqm 300.00

(b) For radial/inclined block outs

Sqm 330.00

6 Add/Deduct as under
(a) Add extra on item No.1to 3 & 5 in case F3 or F4 finish is required
Sqm 25%

(b) Deduct over item No.1to 3 & 5 if finish F1 is required

Sqm 20%

(c) Deduct over 1 to 5 if only propping is to be done (excluding planking)

Sqm 40%
to provide rigid support to existing surface.
7 (a) Supply & fixing of copper strip (95% to 98% purity) of 35 cm wide
and 16 gauge in construction joints of RCC works including cutting, R.M. 2760.00
grooving in Z or V shape and gas welding etc. complete.
(b) Supply & fixing 6 mm thick rubber water seal of approved quality in
construction/contraction joints as per drawing complete in all respect.
i 200 mm wide R.M. 525.00
ii 305 mm wide R.M. 675.00
(c) Supply & fixing 6 mm thick PVC water seal of approved quality in
construction/contraction joint as per drawing complete in all respect.
i 200 mm wide R.M. 630.00
ii 305 mm wide R.M. 800.00
8 Steel shuttering for precasting R.C.C. members for railing of bridges
Sqm 360.00
with all lifts complete.(Area of railing)
9 (a) Labour charges for steel reinforcement including bending, binding, and
placing in position all reinforcement as per drawing including cost of kg 13.00
binding wire and all leads and lifts.
(b) Supplying of M.S. reinforcement including labour charges for bending
binding and placing in position all reinforcement as per drawing
including cost of binding wire and all leads and lifts using.
i Plain bars (IS:432) Kg. 83.00
ii Tor or ribbed bars (IS :1786) Kg. 89.00
10 Extra labour charges for RCC due to obstruction in laying and placing
the reinforced cement concrete due to reinforcement.
(a) In foundation rafts, beams, columns bases stilling basins, buckets,
Cum 140.00
aprons etc. (non suspended horizontally laid mass concrete)
(b) Columns, slabs, cantilevers projections staircases, lintels, beams,
chajjas, Retaining walls, piers, abutments, galleries, arch covers, bed Cum 200.00
plates, sluice capstan bases etc.
(c) Aqueduct troughs, siphon conduits, box type sluice barrels, domes
spiral shafts or stair cases ( thin walled section) and ogee crests, baffle Cum 400.00
or chute blocks, end sills, buckets, projects coping, extended sill etc.

35 CENTERING, SHUTTERING AND RCC

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER - XI

FOUNDATION AND SURFACE TREATMENT

NOTE:-
(1) Provision of any item of this chapter in an estimate should only be taken with the permission of the
Superintending Engineer.
(2) These rates are at work site inclusive of all leads and lifts and also inclusive of all taxes, levies,
Contractor's profit and royalty etc.

(3) The rates in this chapter are inclusive of de-watering wherever required.
Unit Rate in Rs.
S.No. Item

PART A: FOUNDATION TREATMENT

Note- These rates for complete job and also includes maintaining and
furnishing of all data, test result and consumption statement in prescribed
formats.
1 (a) Drilling holes of 35 mm diameter for anchor rods.
i) Upto 1.50 m depth meter 129.00
ii) Beyond 1.5 m for each subsequent metre meter 181.00
(b) Labour charges for Fixing of anchor bars in neat cement grout including Each 245.00
cost of cement and curing etc. complete
(c) Supply of Tor steel anchor bars of required diameter, length and shape at Kg 72.00
site of work complete.
2 Drilling 35 mm to 48 mm dia holes in all types of rock or artificial hard
material like concrete or masonary for consolidation/ curtain grouting in
stages by percussion drilling including cost of drilling equipment,
compressed air, water etc. complete & re-drilling in the hole through set
grout, if required.
(a) Up to 5 m depth meter 861.00
(b) From 5 to 10 m depth meter 1277.00
(c) From 10 to 15 m depth meter 1836.00
(d) From 15 to 20 m depth meter 2601.00
(e) From 20 to 25 m depth meter 3162.00
(f) Beyond 25 m depth meter 3871.00
3 Drilling more than 48 mm but upto 76 mm dia, holes in all types of rock
or artificial hard material like concrete or masonry for consolidation/
curtain grouting in stages by percussion drilling including cost of drilling
equipment, compressed air, water etc. complete and re-drilling in the hole
through set grout if required.
(a) Up to 5 m depth meter 1543.00
(b) From 5 to 10 m depth meter 1879.00
(c) From 10 to 15 m depth meter 2479.00
(d) From 15 to 20 m depth meter 3558.00
(e) From 20 to 25 m depth meter 4031.00
(f) Beyond 25 m depth meter 4647.00

36 FOUNDATION AND SURFACE TREAT MENT

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

4 Drilling 35 mm to 48 mm dia, holes in over burden hard soil compacted

earth, morrum etc. for consolidation / curtain grouting in stages by
percussion drilling including cost of drilling equipment, compressed air,
water etc. complete and re-drilling in the hole through set grout if
required.
(a) Up to 5 m depth meter 625.00
(b) From 5 to 10 m depth meter 810.00
(c) From 10 to 15 m depth meter 1010.00
(d) From 15 to 20 m depth meter 1395.00
(e) From 20 to 25 m depth meter 1545.00
(f) Beyond 25 m depth meter 1845.00
5 Drilling more than 48 mm but upto 76 mm dia, holes in over burden hard
soil compacted earth, morrum etc. for consolidation / curtain grouting in
stages by percussion drilling including cost of drilling equipment,
compressed air, water etc. complete and re-drilling in the hole through set
grout if required.
(a) Up to 5 m depth meter 919.00
(b) From 5 to 10 m depth meter 1231.00
(c) From 10 to 15 m depth meter 1272.00
(d) From 15 to 20 m depth meter 1567.00
(e) From 20 to 25 m depth meter 1814.00
(f) Beyond 25 m depth meter 2081.00
6 Supplying and lowering into holes and fixing of casing pipes of suitable meter 1061.00
diameter to enable drilling of minimum 48 mm dia grout holes.
7 Washing and open flushing of drilled holes by alternate jet of air and Hole / 704.00
water under pressure prior to pressure washing and flushing or grout after Stage
stage grouting including cost of equipment, compressed air and etc.
8 complete.
Normal pressure washing of drilled hole in stages in approved pattern for Hole / 1521.00
cleaning of clay, soil and other filler materials from the seams and joints Stage
in the foundation rock by establishing connections under pressure with air
& water including cost of equipment, accessories compressed air, water,
labour, admixtures if any required etc. complete as per specification.
9 Grouting of drilled holes minimum 35 mm dia with or without packers M.T. 12143.00
with cement/ clay and or chemicals (in the form of slurry with water) in
prescribed ratio till refusal including cost of grouting equipment,
compressed air and water etc. complete but excluding cost of cement, clay
and chemicals (only dry weight of ingredients excluding chemicals to be
considered ) with a working pressure upto 15 kg/Cm2 (Dry cement
consumption)

10 Conducting water intake test in test holes under pressure for determining Each 1456.00
permeability before or after grouting including cost of equipment and
water etc. complete
11 Add extra if works are performed through drainage gallery
(a) Over item No.2, 3, 4 & 5 25%
(b) Over item No. 7, 8 & 9 10%

37 FOUNDATION AND SURFACE TREAT MENT

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

PART B : PREPARATION OF FOUNDATION AND SURFACE

TREATMENT
12 Preparation of foundation of structure including removal of all loose
stones, silt and final washing.
(a) By manual labour Sqm 23.00
(b) By compressed air & water under pressure Sqm 70.00
13 Preparation of surface of existing concrete surface/ masonry in lime Sqm 205.00
mortar/ cement mortar including removal of organic deposit by washing
with etching compound and use of wet sand blasting and final washing the
surface with air and water jet including cost of all material and equipment
required for the work complete.
14 Prepration of old masonry surfaces before laying of further masonry or Sqm 118.00
concrete over it by cleaning the surface and mortar joints with brushing
and raking finally, washing by compressed air & water under pressure.
15 Chipping concrete surface, cleaning the exposed surface of steel and Sqm 69.0
concrete with wire brush, washing with water complete as per
specifications excluding scaffolding etc.
16 (a) 37 mm thick guniting with cement mortar (1:3) on concrete/masonry Sqm 1497.0
surface after proper fixing of 9 gauge welded mesh of good quality rust
free of size 50 mm x 50 mm in TWO layers with anchors / clamps in
stone masonry / concrete, after racking the joints clean the surface by
compressed air & water jet. Apply epoxy and anchor first layer of mesh
with surface to be treated then 15 mm thick mortar is to be applied with
pressure gun. After hardening of first layer of mortar anchor the second
layer of mesh and apply 22 mm thick cement plaster, complete in all
respect as per technical specification.

(b) 37 mm thick guniting with cement mortar (1:3) on concrete/masonry Sqm 1094.0
surface after proper fixing of 9 gauge welded mesh of good quality rust
free of size 50 mm x 50 mm in ONE layers with anchors / clamps in
stone masonry / concrete, after racking the joints clean the surface by
compressed air & water jet. Apply epoxy and 15 mm thick mortar with
compressed air gun on the surface to be treated. After hardening of first
layer of mortar anchor the welded wire mesh and apply 22 mm thick
cement plaster, complete in all respect as per technical specification.

(c) 22 mm thick guniting with cement mortar (1:3) on concrete/masonry Sqm 917.0
surface after proper fixing of 9 gauge welded mesh of good quality rust
free of size 50 mm x 50 mm in ONE layer fixed with anchors / clamps in
stone masonry / concrete, after racking the joints clean the surface by
compressed air & water jet. Apply epoxy, anchor the mesh and apply 22
mm thick cement plaster with pressure gun, complete in all respect as per
technical specification.

38 FOUNDATION AND SURFACE TREAT MENT

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

17 (a) 37 mm thick shotcrete by wet mix process, applied with compressed air Sqm 1673.0
gun after chipping of defective concrete / masonry, racking the joints,
cleaning of surface thoroughly with wet sand blasting after fixing of 9
gauge good quality rust free welded mesh of size 50 mm x 50 mm in
TWO layers with anchors / clamps. After racking the joints clean the
surface thoroughy by wet sand blasting, anchor the first layer of welded
mesh in position and apply 15 mm cement concrete (1:2:1) by pressure
gun and after hardening of first layer, anchor second layer of welded wire
mesh, apply 22 mm thick cement concrete complete in all respect. Cement
concrete comprising of cement, sand, coarse aggregate, water and quick
setting compound in the proportion 1:2:1, sand and coarse aggregate
conforming to IS 383 and table no. 1 of IS:9012 respectively.

(b) 37 mm thick shotcrete by wet mix process, applied with compressed air Sqm 1275.0
gun after chipping of defective concrete / masonry, racking the joints,
cleaning of surface thoroughly with wet sand blasting after fixing of 9
gauge good quality rust free welded mesh of size 50 mm x 50 mm in
ONE layer with anchors / clamps. After racking the joints clean the
surface thoroughy by wet sand blasting apply 15 mm cement concrete
(1:2:1) by pressure gun and after hardening of first layer, anchor welded
wire mesh, apply 22 mm thick cement concrete complete in all respect.
Cement concrete comprising of cement, sand, coarse aggregate, water and
quick setting compound in the proportion 1:2:1, sand and coarse aggregate
conforming to IS 383 and table no. 1 of IS:9012 respectively.

(c) 22 mm thick shotcrete by wet mix process, applied with compressed air Sqm 1135.0
gun after chipping of defective concrete / masonry, racking the joints,
cleaning of surface thoroughly with wet sand blasting after fixing of 9
gauge good quality rust free welded mesh of size 50 mm x 50 mm in
ONE layer with anchors / clamps. After racking the joints clean the
surface thoroughy by wet sand blasting anchor welded wire mesh
properly, apply 22 mm thick cement concrete complete in all respect.
Cement concrete comprising of cement, sand, coarse aggregate, water and
quick setting compound in the proportion 1:2:1, sand and coarse aggregate
conforming to IS 383 and table no. 1 of IS:9012 respectively.

18 Add extra over item No. 16 &17 for each subsequent height 3.00 m or Sqm 65.0
part there-of above initial lift of 5 m from ground level (upward or
19 downward)
Reaming, redrilling and pressure jet flushing of foundation holes of NX Per meter 2325
size, in the drainage gallery of dam, using diamond drill bit of suitable
size, diamond reamer shell with using hydraulically operated rotary core
drilling equipments, rods of suitable length to specified depth, fixing PVC
pipes with caps, including cost of materials, hire charges of equipments,
fuel, labour with all leads and lift etc. complete as directed by Engineer in
Charge.

20 Reaming, redrilling and pressure jet flushing of porous holes of 200 mm Per meter 4650
dia, in the drainage gallery of dam, using diamond drill bit of suitable
size, diamond reamer shell with using hydraulically operated rotary core
drilling equipments, rods of suitable length to specified depth, fixing PVC
pipes with caps, including cost of materials, hire charges of equipments,
fuel, labour with all leads and lift etc. complete as directed by Engineer in
Charge.

39 FOUNDATION AND SURFACE TREAT MENT

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER-XII
GATE AND ALLIED WORKS

Item Description of item Unit Rates in

No. Rs.
1 A Design, drawing, fabrication, supply, erection, testing and commissioning of tonne 169359.00
Embedded parts consisting of sill beams, vertical tracks, vertical seal tracks,
sealing frame, guide tracks/rails, wall plates, seal seats, anchors, anchor girders,
yoke girders, tie flats, trunnion supports, rope and pulley supports etc. and any
required necessary item, with all accessories as per relevant IS code, for all type
radial gates/ Vertical lift fix wheel type sluice and Canal gates/Stop log gates
including cost of all materials, machinery, labour, cutting, aligning,
anchoring, welding, finishing, cleaning, tools and tackles, applying two coat
of zinc rich epoxy primer to give dry film thickness of 70± 5 microns and
finish coat (two coats) of solvent less coal tar epoxy paint using airless spray to
provide dry film thickness of 150± 5 microns per coat thus total dry film
thickness of all coats, including primer coating, should not be less than 350
microns., including packing & forwarding, transportation charges complete
item, as per specifications and approved drawings.
B Design, Drawing, fabrication, supply, erection, testing and commissioning of tonne 123305.00
Vent liners (steel liners for sluice/tunnel or as per requirement in
Dam/irrigation system) including Embedded parts consisting of liner plates,
anchors, stiffeners, girders, fasteners etc. and any required necessary item, with
all accessories for all types of Gates/ sluice channels/ any section of water
resources projects including cost of all materials, machinery, labour, cutting,
aligning, anchoring, welding, finishing, cleaning, tools and tackles, applying two
coat of zinc rich epoxy primer to give dry film thickness of 70± 5 microns and
finish coat (two coats) of solvent less coal tar epoxy paint using airless spray
to provide dry film thickness of 150± 5 microns per coat thus total dry
film thickness of all coats, including primer coating, should not be less
than 350 microns., including packing & forwarding, transportation charges
complete, as per specifications and approved drawings.

2 Design, Drawing, fabrication, supply, erection, testing and commissioning of tonne 175746.00
Radial gate consisting of skin plate, stiffeners, horizontal girders, sector arms,
trunnion assemblies, tie beam, pulley supports, bracings, rubber seals, clamp
plates etc., with all accessories as per relevant IS code for radial gates
including cost of all materials, machinery, labour, cutting, bending, aligning,
anchoring, welding, finishing, cleaning, tools and tackles, applying two
coat of zinc rich epoxy primer to give dry film thickness of 70± 5 microns
and finish coat (two coats) of solvent less coal tar epoxy paint using airless
spray to provide dry film thickness of 150± 5 microns per coat thus total dry
film thickness of all coats, including primer coating, should not be less than
350 microns., seal fixing etc., complete as per specifications and approved
drawings complete, including packing & forwarding, transportation charges for
structural steel components and other materials.

40 GATE AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

3 Design, Drawing, fabrication, supply, erection, testing and commissioning of tonne 176935.00
Vertical lift fix wheel type sliding gate/inter changeable Stop log gates
consisting of skin plate, stiffeners, horizontal girders, pulley, pulley supports,
bracings, lifting lug, bracket, rubber seals, clamps plates etc., with all
accessories as per relevant for Canal, sluice Vertical gates and spillway gates
including cost of all materials, machinery, labour, cutting, bending, aligning,
anchoring, welding, seal fixing, tools and tackles etc., finishing, cleaning,
applying two coat of zinc rich epoxy primer to give dry film thickness of 70± 5
microns and finish coat(two coats)of solvent less coal tar epoxy paint using
airless spray to provide dry film thickness of 150 ± 5 microns per coat thus total
dry film thickness of all coats, including primer coating, should not be less
than 350 microns., complete as per specifications and approved drawings
complete, including packing & forwarding, transportation charges for
structural steel components and other materials.

4 Design, Drawing, fabrication, supply, erection, testing and commissioning tonne 174880.00
of Vertical lift sliding type gate with frame consisting of skin plate,
sealing frame, stiffeners, horizontal and vertical girders, guide, stainless
steel flat/Brass flat, rivets, wedges, lifting rods etc., with all accessories as per
relevant IS code including frame & gate complete set for Canal Cross, Escape,
Head regulator /Tank head regulator including cost of all materials,
machinery, labour, cutting, aligning, welding, finishing, cleaning, seal
fixing, tools and tackles etc., applying two coat of zinc rich epoxy primer to
give dry film thickness of 70±5 microns and finish coat (two coats) of solvent
less coal tar epoxy paint using airless spray to provide dry film thickness of
150±5 microns per coat thus total dry film thickness of all coats,
including primer coating, should not be less than 350 microns., complete as per
specifications and approved drawings with all lead and lifts, including
packing & forwarding, transportation charges for structural steel
5 components and other
Design, Drawing, materials.supply, erection, testing and commissioning of tonne
fabrication, 174810.00
Vertical lift sliding type Dam Shutter gates interchangeable consisting of
sealing frame (embedded parts), skin plate of shutters, stiffeners, horizontal and
vertical girders, guide, stainless steel flat, lifting hooks, clits fasteners etc., with
all accessories including frame & gate complete set for Barrage/ Stop dam/
waste weir / spillway including cost of all materials, machinery, labour,
cutting, aligning, welding, finishing, cleaning, tools and tackles, seal fixing,
applying one coat of zinc rich epoxy primer and three coats of cold applied
coal tar epoxy paint, including primer coating, should not be less than 350
microns., etc. complete as per specifications and approved drawings,
including packing & forwarding, transportation charges for structural steel
components and other materials.

6 Design, Drawing, fabrication, supply, erection, testing and commissioning of Per 84757.00
Adequate capacity electrically operated rope drum hoist according to relevant IS tonne
code, consisting of hoist platform bridge, rope drums, connecting shaft, gear capacit
system, Reduction gear unit, electric motor, electro- magnetic brake system, y
control panel, pulleys, wire rope, gate position indicator, limit switch with
inbuilt manual operating system, etc. complete, with all accessories for
operating gates including cost of all materials, machinery, labour, cutting,
aligning, anchoring, welding, finishing, cleaning, greasing, oil filling, tools and
tackles, applying two coats of zinc chromate red oxide primer and three coats of
approved synthetic enamel paint etc., complete as per specifications and
approved drawings, including packing & forwarding, transportation charges for
all materials.

41 GATE AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

7 Design, Drawing, fabrication, supply, erection, testing and commissioning of Per 77299.00
Adequate capacity manually operated rope drum hoist according to relevant tonne
IS code, consisting of hoist platform bridge, rope drums, connecting shaft, gear capacit
system unit, pulleys, wire rope, Gate position indicator, manual operation y
system, etc. complete, with all accessories for operating gates including cost of
all materials, machinery, labour, cutting, aligning, anchoring, welding, finishing,
cleaning, greasing, oil filling, tools and tackles, applying two coats of zinc
chromate red oxide primer and three coats of approved synthetic enamel paint
etc., complete as per specifications and approved drawings, including packing
& forwarding, transportation charges for all materials.

8 A Design, Drawing, fabrication, supply, erection, testing and commissioning of Per 72118.00
Adequate capacity manually operated screw type hoist according to relevant tonne
IS code, consisting of supporting structure, platform bridge etc., operating capacit
handle, gate position indicator, plumber block, couplings with all required y
accessories for operating Head/cross/ escape regulator gate including cost
of all materials, machinery, labour, tools and tackeles, cutting, aligning,
anchoring, welding, finishing, cleaning, greasing, oiling, applying two coats of
zinc chromate red oxide primer and three coats of approved synthetic enamel
paint etc., complete as per specifications and approved drawings with all lead
and lifts, including packing & forwarding, transportation charges for structural
steel components and other materials.

B Design, Drawing, fabrication, supply, erection, testing and commissioning of Per 76182.00
Adequate capacity Electrically operated screw type hoist according to relevant tonne
IS code, consisting of supporting structure, platform bridge etc., operating capacit
handle, gate position indicator, plumber block, couplings, motor, reduction gear y
unit, limit switch, control panel, cables, with inbuilt manually operation with all
required accessories for operating Head/cross/ escape regulator gate including
cost of all materials, machinery, labour, tools and tackeles, cutting, aligning,
anchoring, welding, finishing, cleaning, greasing, oiling, applying two coats of
zinc chromate red oxide primer and three coats of approved synthetic
enamel paint etc., complete as per specifications and approved drawings with all
lead and lifts, including packing & forwarding, transportation charges for all
materials.
9 Design, drawing, fabrication, supply, erection, testing and commissioning of Per 304081.00
adequate capacity Moving Gantry Crane according to relevant IS code consisting tonne
of rail mounted gantry frame, top platform with handling long/cross travel capacit
arrangements, rope drums, gear systems, rails, electric motors, electromagnetic y
brake system, operator and panel cabin, control panel, wire rope, ladder,
motorized cable reeling drum, suitable counter weight etc. with all accessories
for Operating stop log gates elements including cost of all materials,
machinery, tools and tackles, labour, aligning, anchoring, welding, cleaning,
greasing, applying two coats of zinc chromate red oxide primer three coats
of approved synthetic enamel paint etc., complete as per specifications and
approved drawings with all lead and lifts, including packing &
forwarding, transportation, charges for all materials.

42 GATE AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

10 Design, Drawing, fabrication, supply, erection, testing and commissioning tonne 234342.00
of Automatic lifting beam with all accessories, like automatic
detach/attach system, hooks/rollers, guides, pins complete for handling,
lowering and lifting of Stop log/ emergency gates including cost of all
materials, machinery, tools and tackles, labour, cutting, aligning,
welding, finishing, cleaning, applying one coat of zinc rich epoxy primer
and two coats of cold applied coal tar epoxy paint etc., complete as per
specifications and approved drawings, including packing &
forwarding, transportation charges for structural steel components
and other materials.(per tonne weight)

11 Design, Drawing, fabrication, supply, erection and commissioning of tonne 142238.00

Trestle assy/ Railing decking/Trash rack/Structural steel hoist bridge/
structural steel hoist supporting structure for monorail / Catwalk bridge for
connecting spillway piers for all type of sluice with embedded parts consisting
of columns, beams, bracings, stiffeners, ties, chequered plate covering, hand
railing, ladder etc., with all other accessories for operating gates, other structure
including cost of all materials, machinery, labour, tools and tackles,
cutting, aligning, anchoring, welding, finishing, cleaning, applying two
coats of zinc chromate red oxide primer and three coats of approved
synthetic enamel paint etc., complete as per specifications and approved
drawings, including packing & forwarding, transportation charges for
structural steel components and other materials.

12 Design, Drawing, fabrication, supply, erection and commissioning per 95124.00

of adequate capacity Electrically operated mono-rail hoist assembly tonne
consisting of electric motor, rope drum, gear system, wire rope with lifting capacit
attachment, Monorail long beam, equalizer idle pulleys, festoon cabling, y
control panel etc., with all accessories for operating pump house stop-log gate
including cost of all materials (excluding only hoisting supporting trestle
column structure), machinery, labour, cleaning, greasing etc., complete as
per specifications and approved drawings, including packing &
forwarding transportation charges for structural steel components and other
materials.
13 Design, Drawing, fabrication, supply, erection, testing and commissioning Per 164776.00
of EOT crane consisting of double girder box type construction, rail Tonne
mounted end carriages with long and cross travel arrangement, main and capacit
auxiliary hoists of specified capacity, rails, pendant control, gear boxes, electric y
motors, brakes, rope drums, wire ropes, sheaves, end buffer stoppers,
pendant operated DSL bus bars with all accessories for main and auxiliary
hoists for handling pumps and accessories in pump house including cost of all
materials, machinery, labour, cutting, aligning, welding, finishing,
cleaning, greasing, applying two coats of zinc chromate red oxide
primer and three coats of synthetic enamel paint etc., complete as per
specifications and approved drawings with all lead and lifts, including
packing & forwarding transportation charges for structural steel
components and other materials.

43 GATE AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

14 Design, Drawing, fabrication, supply, erection, testing and commissioning per 150924.00
of Hydraulic Hoist for Spill way, Head Sluice & other Regulating gates, tonne
with all accessories like Power Pack, duly filled with oil, Hydraulic cylinder, capacit
Hydraulic cylinder pipe line, Limit Switch, Dial indicator panel, Cable, y
Control panel etc including cost of all materials, machinery, labour, cutting,
aligning, welding, finishing, cleaning, greasing, applying two coats of
zinc chromate red oxide primer and three coats of synthetic enamel paint
etc. with all scope of work, complete as per specifications and approved
drawings with all lead and lifts, including packing & forwarding transportation
charges for structural steel components and other materials.

15 The bifurcation of cost of work at various stage of construction/work for item no.
1 to 14
A Fabrication work excluding materials including cost of machinery, labour, 25% Cost of
cutting, aligning, anchoring, welding, finishing, cleaning, applying one coat the Item
of zinc rich epoxy primer and three coats of cold applied coal tar epoxy
paint etc., including packing & forwarding charges as per specifications and
approved drawings.
B Fabrication work including cost of all materials, machinery, labour, cutting, 70% Cost of
aligning, anchoring, welding, finishing, cleaning, applying one coat of zinc the Item
rich epoxy primer and three coats of cold applied coal tar epoxy paint etc.,
including packing & forwarding charges as per specifications and approved
drawings.
C Erection work with commissioning, testing for above item of work 30% Cost of
excluding fabricated items including cost of all required materials, tools the Item
and tackles for erection work, machinery, labour, cutting, aligning,
anchoring, welding, finishing, cleaning, etc., including packing &
forwarding, transportation charges, as per specifications and approved
drawings.
16 Design, Drawing, fabrication, supply, erection, testing and commissioning of Rail M 10722.00
track using 45 kg/m standard rails on bridge for movement of gantry crane
for handling and operating stop log gate elements including cost of all
materials, machinery, labour, aligning, anchoring, welding, cleaning, applying
one coat of zinc rich epoxy primer and two coats of cold applied coal tar
epoxy paint for buffers and rail supporting plates etc., complete as per
specifications and approved drawings with all lead and lifts, including packing &
forwarding transportation charges for all materials.

17 Providing fabrication and fitting work of Stainless steel flat on Embedded kg 732.00
parts (on Departmental section, only MS section Given by department) of
gates with testing , including cost of all materials (SS flat and welding rods
etc.), machinery, tools and tackles, labour, cutting, aligning, welding, finishing,
cleaning, applying two coat of cement primer etc., complete as per specifications
and approved drawings, including packing & forwarding, transportation charges
for structural steel components and other materials.

44 GATE AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

Providing Casting machining and assembling of Cast Steel Rollers kg 494.00

assembly complete with testing, including cost of all materials as Cast steel
Rollers, Stainless steel Eccentric pin/shaft with square cut shape in one
end for adjustment, Lock plate, bronze bush, cover plate, nut bolts,
machinery, labour, cutting, aligning, welding, finishing, cleaning,
applying one coat of zinc rich epoxy primer and two coats of cold applied
coal tar epoxy paint, etc., complete as per specifications and approved
drawings with all lead and lifts, tools and tackles, including packing &
forwarding, transportation charges for structural steel components and
other materials.

19 Providing Casting, dressing and assembling of Cast Iron Ballast weight assembly kg 106.00
complete as per drawing with testing, including cost of all materials as Cast
iron Ballast weight, Suitable type tapped threaded hole with nut hook for
lifting in all sides, with machinery, labour, cutting, aligning, welding, finishing,
cleaning, etc., complete as per specifications and approved drawings
with all lead and lifts, tools and tackles including packing & forwarding
transportation charges for structural steel components and other materials.

20 Providing Casting machining and assembling of Cast Iron Items for Tank, canal, 0.00
barrage, stop dam gates as CI wedges with suitable L-end key nut bolts, CI
couplings, CI guides, assembly complete as per drawing with testing
including cost of all materials with machinery, labour, cutting, aligning,
welding, finishing, cleaning, etc., complete as per specifications and approved
drawings with all lead and lifts, including packing & forwarding charges for
structural steel components and other materials.

A CI wedges with suitable L-end key nut bolts kg 165.00

B CI couplings, Guides, etc. kg 171.00
21 Providing Fabrication, machining and assembling of different types of MS
Anchors/ MS chuck nut for Gates assembly, complete as per drawing with
testing including cost of all materials, applying one coat of zinc rich epoxy
primer and two coats of cold applied coal tar epoxy paint with machinery,
labour, cutting, aligning, welding, finishing, cleaning, etc., complete as per
specifications and approved drawings with all lead and lifts,
including packing & forwarding charges for structural steel components and
other materials.

A MS Chuck Nut kg 200.00

B U, J, H, I type anchors kg 130.00
C Anchor bolts with two nut and two washers kg 152.00
22 Providing Casting machining and assembling of Head stocks assembly
with handle complete for operating Tank, canal, barrage, stop dam gates, as per
drawing with testing, including cost of all materials as head stock
body, GM Nut, Warm wheel, Gear, Bush, Pin, operating handle etc. with
machinery, labour, cutting, aligning, welding, finishing, cleaning, painting etc.,
complete as per specifications and approved drawings with all lead and lifts,
including packing & forwarding transportation charges for structural steel
components and other materials.

A Head Stock Worm & wheel type coupled set 63/56mm dia mm dia. threaded kg 288.00
Nut (Model WW- 90) two tone capacity, approx-322 kg weight
B Head Stock Worm & wheel type, single set, 63mm/56mm dia threaded nut kg 254.00
(Model WW-90) one tone capacity approx-175 kg weight
C Head Stock screw jack type 50mm dia. threaded Nut (Model M-75), 0.750 kg 201.00
tonne capacity, approx-45 kg weight

45 GATE AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

D Head Stock screw jack type 45mm dia. threaded Nut (Model M-70), 0.700 kg 200.00
tonne capacity , approx-42 kg
E Head Stock screw jack type 36mm dia. threaded Nut (Model S-36),0.400 kg 267.00
tonne capacity, approx-19.5 kg
23 Straightening and machining work of structural steel sections (departmental
materials) complete job, with all machinery as plainer machine etc., labour,
cutting, aligning, finishing, cleaning etc., complete as per specifications and
approved drawings, with all lead and lifts, including packing & forwarding
charges for structural steel components and other materials.
23.01 Straightening work any steel sections kg 5.00
23.02 Machining work of structural steel sections like as Guide T, Track etc. with sqm 2924.00
plainer machine
24 Providing, fabrication, threading (Square and V threading as required),
machining, straightening of MS Round bar complete as per drawing with testing,
including cost of all materials, with machinery, labour, cutting, aligning,
welding, finishing, cleaning etc., complete as per specifications and approved
drawings with all lead and lifts, including packing & forwarding transportation
charges for structural steel components and other materials.

A Rate for double start square threading for 63mm dia. round bar with materials kg 185.00
B Rate for double start square threading for 63mm dia. round bar without m 2008.00
C Rate for single start square threading for 63mm dia. round bar with materials kg 174.00
D Rate for single start square threading for 63mm dia. round bar without m 1875.00
E Rate for double start square threading for 56mm dia. round bar with materials kg 168.00
F Rate for double start square threading for 56mm dia. round bar without m 1585.00
G Rate for single start square threading for 56mm dia./ 50mm dia/ 45mm dia. kg 169.00
round bar with materials
H Rate for single start square threading for 56mm dia./ 50mm dia/ 45mm dia. m 1126.00
round bar without materials
I Rate for single start square threading for 36mm dia./32mm dia round bar with kg 162.00
materials
J Rate for single start square threading for 36mm dia./ 32mm dia round bar m 571.00
without materials
K Rate for "V " threading for Round bar with materials
(i) 63 mm dia kg 169.00
(ii) 56 mm dia kg 159.00
(iii) 50 mm dia. kg 153.00
(iv) 45 mm dia kg 155.00
(v) 36 mm dia. kg 149.00
(vi) 32 mm dia. kg 149.00
L Rate for "V " threading for Round bar without materials
(i) 63 mm dia m 1807.00
(ii) 56 mm dia m 1687.00
(iii) 50 mm dia. m 1427.00
(iv) 45 mm dia m 1014.00
(v) 36 mm dia. m 514.00
(vi) 32 mm dia. m 514.00

46 GATE AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

25 Providing, Fabrication, machining with straightening work of Guide Tee,

Track, Sealing frame, Leaf frame or any part of gate's, complete as per
drawing with testing, including cost of all materials, with machinery,
labour, tools and tackles cutting, aligning, welding, finishing, cleaning etc.,
applying one coat of zinc rich epoxy primer and two coats of cold applied
coal tar epoxy paint, etc., complete as per specifications and
approved drawings with all lead and lifts, including packing &
forwarding, transportation charges for structural steel components and other
materials.
A Rate of work with all materials kg 127.00
B Rate of work without materials kg 34.00
C Erection work of fabricated gates, any parts of gate's and any accessories of kg 58.00
gate's, complete as per drawing with testing, including cost of all
materials required for completing the job like welding rods, tools
tackles etc., with machinery, labour, tools and tackles cutting, aligning,
welding, finishing, cleaning etc., applying one coat of zinc rich epoxy
primer and two coats of cold applied coal tar epoxy paint, etc.,
complete as per specifications and approved drawings with all lead
and lifts, including packing & forwarding, transportation charges for
structural steel components and other materials.

26 Transportation of hydraulic gates/ heavy earth moving machineries and

other equipment’s, plants etc. and their components, materials, loading &
unloading work, from FOR to different irrigation project sites of Water
Resources Department in Rajasthan by Pacca/ Kachcha Road.
A 12.00 Tonne minimum capacity open body truck and above km 104.00
B 9.00 Tonne minimum capacity normal half body truck km 90.00
C 9.00 Tonne minimum capacity open body truck km 91.00
D 6.00 Tonne minimum capacity normal half body truck km 74.00
E 6.00 Tonne minimum capacity open body truck km 77.00
F 4.00 Tonne minimum capacity normal body truck km 71.00
G Trailer truck open body approx 14m long for HEM and equivalent km 172.00
machinery/items transportation work capacity above 25MT
H Loading & unloading of steel material, weighing at MPLUN/ SAIL/ Other tonne 1173.00
outside stores and transportation from MPLUN/ SAIL/ Other stores to
CMU campus and unloading of material.
I Over dimension charges for gate job transportation
(i) 12.0 Tonne minimum capacity open body truck and above with over Km 111.00
dimension job
(ii) 9.0 Tonne minimum capacity normal half body truck with over dimension Km 96.00
(iii) 9.0 Tonne minimum capacity open body truck with over dimension job Km 97.00
(iv) 6.0 Tonne minimum capacity normal half body truck with over dimension Km 78.00
(v) 6.0 Tonne minimum capacity open body truck with over dimension job Km 82.00
(vi) 4.00 Tonne minimum capacity normal body truck with over dimension job Km 75.00
27 Providing MS Nut Bolts of required size and type, as per specifications with kg 124.00
testing, including all lead and lifts, packing & forwarding charges for all
components etc. complete.
28 Providing High tensile MS Nut Bolts of required size and type, as kg 158.00
per specifications with testing, including all lead and lifts, packing &
forwarding charges for all components etc. complete.

47 GATE AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

29 Providing Stainless steel counter shank nut bolts with washer of kg 484.00
required size and type, as per specifications with testing, including all
lead and lifts, packing & forwarding charges for all components etc.
complete.
30 Providing Rubber seals as per IS:11855 for Dam sluice, canal, barrage, stop
dam etc. gates of required size and type and specifications with testing,
including all lead and lifts, packing & forwarding charges for
all components etc. complete.
A Rubber seal musical note type 75mmx33mm x12mm (33mm Bulb) m 679.00
B Rubber seal musical note type 100mmx44mm x14mm (44mm Bulb) m 1137.00
C Rubber seal musical note type 100mmx44mm x14mm (44mm Bulb) Teflon m 2558.00
cladded
D Rubber seal Z type 150mm x75mm x 35mm x 20mm (L-75mm/35mm) m 1942.00
E Rubber seal Flat type 75mm x12mm uncladed m 405.00
F Rubber seal Flat type 100mm x14mm uncladed m 675.00
G Rubber seal Flat type 150mm x20mm uncladed m 1445.00
H Rubber seal Corners musical note type 100mm x44mm x14mm (44mm m 5116.00
bulb), Teflon cladded inside bulb or outside bulb 300mm x300mm long ,
set of two pieces
I Rubber seal musical note type 75mmx33mm x12mm (33mm Bulb) teflon m 1721.00
cladded
J Rubber seal Z type 100mm x55mm x25mm x 20mm (L-55mm/25mm ) uncladed m 1453.00
K Rubber seal Z type 120mm x75mm x 35mm x 20mm (L-75mm/35mm ) uncladed m 1658.00
L Rubber seal Corners musical note type 100mm x44mm x14mm (44mm m 2274.00
bulb), un claded inside bulb or outside bulb 300mmx300mm long, set of two
31 pieces
Painting of Spillway gates, sluice gates, canal gates (both vertical or
radial),stop log gates, exposed embedded parts and all un machined
ferrous surface (hoist cylinders, cylinder heads, hydraulic piping, pipe
fittings, bonnet covers), exposed to water as per IS 14177,for which surface
preparation by blast cleaning of class "B" primer coat (one coat) of
inorganic zinc silicate (preferably airless spray)or alternatively, two coats of
zinc rich primer(containing not less than 85% zinc on dry film) to give
dry film thickness of 70 ± 5 micron and finish coat (two coats) of
solvent less coal tar epoxy paint using airless spray to provide dry film
thickness of 150±5 micron per coats. Thus, total dry film thickness of all the
coats, including primer coating, should not be less than 350 microns, this
will be include expenses on mobilisation and demobilisation of equipments.
For maintenance painting the surface preparation shall be
done by appropriate hand and power tool cleaning, prior to hand power
tool cleaning. Any heavy layer of rust should be removed by chipping
visible oil, grease, dirt and other foreign material be cleaned using solvents
like clean mineral spirits, xylol or white gasoline. After hand and power tool
cleaning the surface should be cleaned of loose dust and debris and/or blast
cleaned as laid down in para 7.0 of IS code 14177. After the surface
preparation the primer and finishing coats shall be carried out as provided
above for painting etc. complete.

A Up to 1.5m height sqm 678.00

B Beyond 1.5m height sqm 713.00

48 GATE AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

32 Painting of lifting beam/lifting tackles are per IS 14177, for which

surface preparation by blast cleaning, as per class "C" or class "B", primer
coat (two coats) of zinc Phosphate primer, to provide dry film thickness
of 40 microns per coat and finish coat (two coats) of alkyd based
micaceous iron oxide paint, using airless spray, to provide minimum dry
film thickness of 65±5 microns per coat, at an interval of 24 hours. Thus,
total dry film thickness of all the coats, including primer coating,
should not be less than 200 microns. This will include expenses on
mobilisation and demobilisation of equipments. For maintenance painting,
the surface preparation shall be done by appropriate hand and power tool
cleaning. Prior to hand and power tool cleaning, any heavy layer of rust
should be removed by chipping. Visible oil, grease, dirt and other foreign
material be cleaned using solvents like clean mineral spirits, xylol or
white gasoline. After hand and power tool cleaning, the surface should be
A cleaned
Upto 1.5ofmloose dust and debris and / or blast cleaned as laid down in para 7.0 of
height sqm 570.00
B beyond 1.5m height sqm 599.00
33 Painting of structural components of Hoist including supporting
structures and surfaces of hydraulic hoist sun exposed to water
as per IS 14177, for which surface preparation by blast cleaning of class 'B',
primer coat (two coats) of Zinc phosphate primer to give dry film thickness
of 40 ± 5microns per coat and finish coat(one coat) of alkyd based micaceous
iron oxide paint give dry film thickness of 65 ± 5 microns followed by two
coats of synthetic enamel paint, using airless spray, to give dry film
thickness of 25 ± 5 microns per coat, at an interval of 24 hours. Thus total
dry film thickness of all the coats, including primer coating, should
not be less than 175 microns. This will include expenses on mobilisation and
demobilisation of equipments. For maintenance painting, the surface
preparation shall be done by appropriate hand and power tool cleaning. Prior to
hand and power tool cleaning, any heavy layer of rust should be
removed by chipping. Visible oil, grease, dirt and other foreign material be
A cleaned
Up to 1.5musing solvents like clean mineral spirits, xylol or white
height sqm 567.00
B Beyond 1.5m height sqm 596.00
34 Painting of machinery, including gearing, housing, shafting, bearing,
pedestals, oil tanks, control cabinets, hoist beams, pipe support, clamps,
ladders etc., of hoists and supporting structures, as per IS 14177, for which
surface preparation by blast cleaning of class 'B', primer coat (one coat)
of Zinc phosphate paint to give a minimum dry film thickness of 50 ± 5
microns and finish coat (three coats) of aluminium paint or synthetic
enamel paint, using airless spray, to provide a dry film thickness of
25 ± 5 microns per coat. Thus, total dry film thickness of all
the coats, including primer coat, should not be less than 125 microns.
This will include expenses on mobilisation and demobilisation of
equipments. For maintenance painting, the surface preparation shall be
done by appropriate hand and power tool cleaning. Prior to hand and
power tool cleaning, any heavy layer of rust should be removed by
chipping. Visible oil, grease, dirt and other foreign material be cleaned
A using solvents
Up to 1.5m like clean mineral spirits, xylol or white gasoline. After
height sqm 473.00
B Beyond 1.5m height sqm 496.00

49 GATE AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

35 Painting of un machined surface, as per IS 14177, for which surface

preparation by blast cleaning of class 'B', primer coat (one coat) of
chlorinated rubber based zinc phosphate primer, to provide a dry
film thickness of 50± 5 microns and finish coat (three coats) of vinyl resin
/chlorinated rubber, using airless spray, to provide a dry film
thickness of 30 ± 5 microns per coat. Thus, total dry film thickness of
all coasts including primer coat should not be less than 125 microns.
Thus will include expenses on mobilisation and demobilisation of
equipments. For maintenance painting, the surface preparation shall be done
by appropriate hand and power tool cleaning. Prior to hand and power tool
cleaning, any heavy layer of rust should be removed by chipping. Visible
oil, grease, dirt and other foreign material be cleaned using solvents like
clean mineral spirits, xylol or white gasoline. After hand and power tool
cleaning, the surface should be cleaned of loose dust and debris and / or
A blast
Up tocleaned as laid down in Para 7.0 of IS Code14177. After the surface
1.5 m height sqm 673.00
B Beyond 1.5 m height sqm 706.00
36 Operation of vertical / radial gates, hoist operation, stop log gates, Gantry Crane, For 4279.00
mono rail etc. at Dams for all seasons round the clock whenever required, as per One
direction of Engineer in-Charge, by providing skilled & semi skilled staff well Shift
conversant with the work of operation of gates as well as meet out all types of 8.00
maintenance & repair work of gates whenever required in any emergency during Hours
operation of the gates including deployment of Chowkidar at gate section of the
Dam.

37 Oiling and greasing of Crest radial gates,Vertical Gates and Intake Service well Sqm 186.00
Gates of Dam including all charges of man and material complete, which include
cleaning of wire rope with petrol / diesel and applying Cardium compound to
wire ropes, oiling & greasing etc complete as per direction of Engineer-in-
Charge.
38 Labour charges for removal of existing wornout/damaged bottom rubber seal of m 650.00
crest Radial Gates, Vertical Gates and Intake Service Well Gates of Dam by
cutting bolts with gas cutter, providing holes in new rubber seal insertion of
sleevs and fixing over gates with nut blots, washer ect including cost of gas (LPG
and Oxygen) cylinder etc complete.
39 Labour charges for removal of existing wornout/damaged side rubber seal of m 603.00
crest Radial Gates, Vertical Gates and Intake Service Well Gates of Dam by
cutting bolts with gas cutter,providing holes in new rubber seal insertion of sleevs
and fixing over gates with nut blots, washer ect including cost of gas (LPG and
Oxygen) cylinder etc complete
40 Labour charges for removal of existing wornout/damaged bottom and side rubber m 371.00
seal of Stop Log Gate of Dam by cutting bolts with gas cutter, providing holes in
new rubber seal insertion of sleevs and fixing over gates with nut blots, washer
ect including cost of gas (LPG and Oxygen) cylinder etc complete
41 Providing and applying one coat of Zinc rich epoxy primer paint (zinc content sqm. 282.00
85%) of approved quality 40 micron dry film thickness to gates/ embedded parts/
hoist components including cost of all materials, labour, removing rust cleaning
surface, scaffolding with all lead and all lifts etc. complete.
42 Providing and applying two coats of anticorrosive bituminous black paint of sqm. 122.00
approved quality 40 micron dry film thickness each coat to gate components such
as horizontal girders/sector and all bracings/ trunnion assembly/ yoke girders/
stiffeners/ foot bridge etc. including cost of all materials, labour, removing rust,
cleaning surface, scaffolding with all lead and lifts etc. complete.

50 GATE AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

43 Providing and filling/ replacing gear oil of approved quality up to the required litre 449.00
gauge level for Reduction gear unit of hoists/ gantry cranes including cost of all
materials, machinery, labour with all leads and lifts etc. complete.
44 Providing and applying grease of approved quality to gate and hoist components kg 572.00
requiring greasing as part of annual maintenance using grease gun wherever
necessary including cost of all materials, machinery, labour, scaffolding etc.
complete.
45 Providing and applying cardium compound of approved quality to wire ropes of kg 201.00
hoists/ gantry cranes as part of annual maintenance including cost of all materials,
machinery, labour etc. complete.
46 Providing and filling/ replacing hydraulic oil of approved quality up to the litre 236.00
required gauge level including cost of all materials, machinery, labour etc.
47 complete. gates/ hoists/ embedded parts for re- painting by removing rust, oil,
Cleaning sqm 84.00
paint, grease etc., by using wire brush, scrubber, rust remover and applying a
coat of rust inhibitive compound etc., complete.
48 Transportation charges with utility van and with four men (two helpers- one
welder and one fitter) with welding parts, cutting items and extra tools and
tackles required for fitting/ repair work of gate parts and head etc.
A upto 50 km Each 6343.00
B for above 50km, per Km extra charge Each 107.00
49 Oiling, Greasing work of gate parts like Headstock, Headstock parts, Roller
Assembly, Operating Rod, Sealing Frame, Guide Tee with all Labor tools and
tackles etc. and Material for vertical lift sliding type/ fix wheel gates excluding
cardium compund and gear oil .
A For gates size up to 1.0 m x 1.0m Each 1579.00
B For gate size above 1 Sqm to 10 Sqm Each 2527.00
C For gate size above 10.00 Sqm to 20.00 Sqm Each 3790.00
50 Genral maintenance of Diesel Generator Set. (Only Labour Charges) Per 3199.00
Set.
51 Greasing and rocker & roller bearing of spillway bridge including cleaning the Per 2987.00
dust, dirt, grease with wire brush, petrol or diesel spray, removing rust with fine Bearin
sand paper filling gease and painting work on out side surface of grease chamber, g
complete in all respect.
52 A Providind of Rubber Seals as per IS 11855 for dams, sliuce, canals, barrage ,stop
log gates etc of required size and type and specifications with testing , including
all lead and lifts, packing and forwording charges for all components etc.
complete in all respect
(i) Rubber Seal Flat type of Size 127mm ×12, 16,20mm / meter 1889.00
(ii) Rubber Seal Flat type with corner of Size 130mm × 25mm / meter 2927.00
(iii) Rubber Seal Flat type with corner of Size 90 mm × 20 mm / meter 2280.00
(iv) Rubber Seal Flat type of Size 72 mm × 25 mm / meter 1469.00
(v) Rubber Seal Flat type with corner of Size 100 mm × 20 mm / meter 2591.00
(vi) Rubber Seal Flat type with corner of Size 125mm x 25 mm with 30mm taper / meter 2601.00
(vii) Rubber Seal Musical Knot, Hollow Bulb type of Size 100mm × 40mm x 15 mm / meter 1669.00
(viii) Rubber Seal Musical Knot, Solid Bulb type of Size 100mm × 45mm x 15 mm / meter 1731.00
(ix) Rubber Seal Musical Knot, Solid Bulb with brass clading type of Size 100mm × / meter 3316.00
45mm x 15 mm
(x) Rubber Seal Musical Knot, Solid Bulb double stem type of Size 160mm × 45mm / meter 2386.00
x 15 mm
(xi) Rubber Seal Musical Knot, Solid Bulb type of Size 75mm × 35mm x 10 mm / meter 1028.00

51 GATE AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

(xii) Rubber Seal Z type of Size 120 mm × 76mm x x30mm x 20 mm / meter 2743.00
(xiii) Rubber Seal Flat type with corner of Size 65 mm × 15 mm / meter 1251.00
(xiv) Rubber Seal Musical Knot, Solid Bulb type of Size 100mm × 35mm x 12 mm / meter 1293.00
(xv) Rubber Seal Musical Knot, Solid Bulb type of Size 85mm × 35mm x 12 mm / meter 1146.00
B Add extra 20% over item no 52 A for prviding rubber seal coated with TEFLON / meter
coating.
53 grade) Timber seal (as per Cum 227802.00
st
Supplying and fixing of M.P Teakwood (I
specification and drawing) with Nut and bolts including removing old
timber seal & fixing new and vacating service bay by shifting on tier (at
service bay) to pier and bringing the tier for maintenance to service bay
and removing old timber seal by opening bolts, drilling holes in timber seal
54 & fixing
Supply etc.fixing
and Complete in all respect.
of sluice/regulator gates for canal using MS plates, channels, kg 138.00
tees, angles, girders etc. of given size and design having suitable brass/gunmetal
lining, rubber seals etc. and desired rod length, capstan head, clamps keys,
hoisting plateform, ladders, supports, etc. complete (excluding civil works)
including painting with zinc rich primer& epoxy paint & delivery at site.

(a) Add extra if worm gears are to be provided in the capstan kg 10.00
(b) Add extra if counter weight type design is followed kg 10.00

(c) Add extra if the opening size is greater than 1 sqm but upto 3 sqm (Drawing and kg 4.00
design shall also be supplied by supplier, for gates having size more than 1.00
sqm)
(d) Add extra, if the opening size is greater than 3 sqm upto 5 sqm requiring heavy kg 15.00
channel/girders.
55 Labour charges for fixing sluice gate including rod clamps & headposts
etc.complete for new & old tanks.
(a) Gate size up to 1 sqm Each 1995.00
(b) Extra for every additional square meter of gates size including rod clamps and Each 1450.00
head posts etc. complete
56 Labour charges for fixing of canal regulator gates complete including rod, clamps
and head posts etc.
(a) Gate size up to 1 sqm Each 1088.00
(b) Extra for every additional square meter of gates size including rod clamps and Each 909.00
head posts etc.complete

52 GATE AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER -XIII
PIPES / FITTINGS / SPECIALS

NOTES:-
1 The rates are inclusive of all taxes, levies, royalty, GST, leads of all material and contractor's profit etc.

2 The pipe of respective pressure rating is allowed only up to 80% of permissible pressure as per IS standards.

3 The rates in this chapter are inclusive of de-watering wherever required.

4 Rate os Providing, lowering, laying, aligning, fixing and jointing of all type of pipes is excluding earthwork
and any civil work required i.e drain , nala , Railway- NH-SH crossing etc.
5 For economic design of piped micro irrigation network, DI / Metalic pipes are not to be used up to diameter
(ID) of 300 mm unless otherwise specific reason.
6 Minimum pressure rating of HDPE pipe for piped micro irrigation network is to be taken PN6 irrespective
of working pressure in pipe.

Pipe Line Work

S. No. Description
Unit Rate in Rs.
1 DI PIPES & SPECIALS
1.1 Providing, lowering, laying, aligning, fixing in position and jointing in trenches.
Ductile Iron(DI) ISI marked K-7 grade S&S pipes as per IS: 8329-2000 (amended up
to date) with internal cement mortar lining suitable for potable water with rubber ring
(EPDM) joints as per IS:5382-1985 including all taxes(central and local),
transportation and freight charges, inspection charges, loading/unloading charges
stacking of pipes including cost of labour and material special (T-bend etc.)
satisfactorily hydraulic testing, disinfection etc complete as per technical specification
and direction of engineer incharge (excluding earthwork ).
Note-Providing and fixing of all requisite sepecials as per drawing, design and layout
are inclusive in RM measurement of the item and shall not be paid separately.
1.1.1 80 mm RMT 1494.00
1.1.2 100 mm RMT 1543.00
1.1.3 150 mm RMT 2189.00
1.1.4 200 mm RMT 2793.00
1.1.5 250 mm RMT 3635.00
1.1.6 300 mm RMT 4643.00
1.1.7 350 mm RMT 5667.00
1.1.8 400 mm RMT 6917.00
1.1.9 450 mm RMT 8176.00
1.1.10 500 mm RMT 9753.00
1.1.11 600 mm RMT 12749.00
1.1.12 700 mm RMT 17092.00
1.1.13 800 mm RMT 21942.00
1.1.14 900 mm RMT 26908.00
1000 mm RMT 32290.00

53 PIPES /FITTINGS/ SPECIALS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

1.2 Providing, lowering, laying in trenches, aligning, fixing in position and jointing
Ductile Iron (DI) ISI marked K-9 grade S&S pipes as per IS:8329-2000 (amended
upto date), with internal cement mortar lining suitable for potable water with rubber
ring (EPDM) joints as per IS: 5382-1985 including all taxes (Central and local),
transportation and freight charges, inspection charges, loading/ unloading charges,
including cost of labour and material, specials (Tee, bend etc.) satisfactory hydraulic
testing, disinfection etc. complete as per technical specifications and direction of
Engineer-in Charge. (excluding earth work).
Note : Providing and fixing of all requisite specials as per drawing, design and layout
are inclusive in RM measurement of the item and shall not be paid separately.
1.2.1 100mm RMT 1764.00
1.2.2 150 mm RMT 2509.00
1.2.3 200 mm RMT 3328.00
1.2.4 250 mm RMT 4421.00
1.2.5 300 mm RMT 5604.00
1.2.6 350 mm RMT 6836.00
1.2.7 400 mm RMT 8326.00
1.2.8 450 mm RMT 9944.00
1.2.9 500 mm RMT 11655.00
1.2.10 600 mm RMT 15252.00
1.2.11 700 mm RMT 19314.00
1.2.12 800 mm RMT 23755.00
1.2.13 900 mm RMT 28928.00
1.2.14 1000 mm RMT 34926.00
1.2.15 1100 mm RMT 42178.00
1.2.16 1200 mm RMT 48906.00
2.0 HDPE PIPES
2.1 Providing, lowering, laying and jointing in trenches. standard lengths HDPE ISI
marked Pipes as per IS-4984: l995 (amended upto date) with necessary jointing
material like mechanical connectors, i.e. thread/ insert joint/ quick release coupler
joint/ compression fitting joint or flanged joint and specials jointing pipe by butt
fusion/ electro fusion welding method, including all taxes , transportation and freight
charges, inspection charges, loading/ unloading charges, stacking of pipes, including
cost of labour and material, specials (Tee, bend etc.), satisfactory hydraulic testing,
disinfection etc. complete as per technical specifications and direction of Engineer-in-
charge of following class and diameter. (excluding earth work)
Note : Providing and fixing of all requisite specials as per drawing, design and layout
are inclusive in RM measurement of the item and shall not be paid. separately. Supply
upto 110 mm dia. in coil & above 110 mm dia straight length in 6M.
2.1 HDPE PE-100 PN-6
2.1.1 63 mm dia RM 161.00
2.1.2 75 mm dia RM 212.00
2.1.3 90 mm dia RM 298.00
2.1.4 110 mm dia RM 444.00
2.1.5 125 mm dia RM 585.00
2.1.6 140 mm dia RM 737.00
2.1.7 160 mm dia RM 928.00
2.1.8 180 mm dia RM 1167.00
2.1.9 200 mm dia RM 1399.00
2.1.10 225 mm dia RM 1762.00
2.1.11 250 mm dia RM 1994.00
2.1.12 280 mm dia RM 2493.00

54 PIPES /FITTINGS/ SPECIALS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

2.1.13 315 mm dia RM 3158.00

2.2 HDPE PE-100 PN-8
2.2.1 63 mm dia RM 178.00
2.2.2 75 mm dia RM 244.00
2.2.3 90 mm dia RM 330.00
2.2.4 110 mm dia RM 475.00
2.2.5 125 mm dia RM 673.00
2.2.6 140 mm dia RM 832.00
2.2.7 160 mm dia RM 1063.00
2.2.8 180 mm dia RM 1313.00
2.2.9 200 mm dia RM 1597.00
2.2.10 225 mm dia RM 2006.00
2.2.11 250 mm dia RM 2435.00
2.2.12 280 mm dia RM 3023.00
2.2.13 315 mm dia RM 3788.00
2.3 HDPE PE-100 PN-10
2.3.1 63 mm dia RM 221.00
2.3.2 75 mm dia RM 307.00
2.3.3 90 mm dia RM 410.00
2.3.4 110 mm dia RM 608.00
2.3.5 125 mm dia RM 825.00
2.3.6 140 mm dia RM 1033.00
2.3.7 160 mm dia RM 1344.00
2.3.8 180 mm dia RM 1688.00
2.3.9 200 mm dia RM 2046.00
2.3.10 225 mm dia RM 2560.00
2.3.11 250 mm dia RM 3721.00
2.3.12 280 mm dia RM 4592.00
2.3.13 315 mm dia RM 5732.00

3.0 MS PIPES and Specials

3.1 Manufacturing, supplying, lowering, laying and jointing in position to correct line
spirally welded SAW/Fabricated MS Pipe having bevelled end plates I coils,
confirming to IS 3589-200 I or its latest revision / amendmendment, for following
thickness and inside diameter including all taxes, transportation and freight charges,
inspection charges, loading/ unloading charges, including cost of labour and material,
specials (Tee, bend etc.), field joints, satisfactory hydraulic testing, disinfection,
commissioning etc. complete as per technical specifications and direction of Engineer-
in-Charge; (excluding earthwork, internal lining and outer coating).
Note : Providing and fixing of all requisite specials as per drawing, design and layout
are inclusive in RM measurement of the item and shall not be paid separately.
A Outer dia of pipe 219.1 mm and thickness
i) 2.6 mm RMT 1626.00
ii) 3.2 mm RMT 1995.00
iii) 4 mm RMT 2485.00
iv) 4.5 mm RMT 2789.00
B Outer dia of pipe 273 mm and thickness
i) 3.6 mm RMT 2801.00
ii) 4 mm RMT 3107.00
iii) 5 mm RMT 3870.00
iv) 6.3 mm RMT 4852.00

55 PIPES /FITTINGS/ SPECIALS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

C Outer dia of pipe 323.9 mm and thickness

i) 4 mm RMT 3695.00
ii) 4.5 mm RMT 4151.00
iii) 5.6 mm RMT 5148.00
iv) 7.1 mm RMT 6496.00
D Outer dia of pipe 355.6 mm and thickness
i) 4 mm RMT 4062.00
ii) 5 mm RMT 5063.00
iii) 5.6 mm RMT 5660.00
iv) 7.1 mm RMT 7146.00
v) 8 mm RMT 8031.00
E Outer dia of pipe 406.4 mm and thickness
i) 4 mm RMT 4648.00
ii) 5 mm RMT 5796.00
iii) 6.3 mm RMT 7280.00
iv) 7.1 mm RMT 8188.00
v) 8.8 mm RMT 10105.00
F Outer dia of pipe 457 mm and thickness
i) 4 mm RMT 5233.00
ii) 5 mm RMT 6527.00
iii) 6.3 mm RMT 8200.00
iv) 7.1 mm RMT 9225.00
v) 8.8 mm RMT 11391.00
G Outer dia of pipe 508 mm and thickness
i) 5 mm RMT 7263.00
ii) 5.6 mm RMT 8125.00
iii) 6.3 mm RMT 9128.00
iv) 7.1 mm RMT 10271.00
v) 8.8 mm RMT 12687.00
vi) 10 mm RMT 14382.00
vii) 11 mm RMT 15789.00
H Outer dia of pipe 610 mm and thickness
i) 5.8 mm RMT 10121.00
ii) 6.3 mm RMT 10984.00
iii) 7.1 mm RMT 12362.00
iv) 8.8 mm RMT 15279.00
v) 10 mm RMT 17328.00
vi) 11 mm RMT 19029.00
vii) 12.5 mm RMT 21570.00
I Outer dia of pipe 711 mm and thickness
i) 6.3 mm RMT 12822.00
ii) 7.1 mm RMT 14433.00
iii) 8 mm RMT 16242.00
iv) 8.8 mm RMT 17846.00
v) 10 mm RMT 20245.00
vi) 11 mm RMT 22237.00
vii) 12.5 mm RMT 25216.00
J Outer dia of pipe 813 mm and thickness
i) 7.1 mm RMT 16525.00
ii) 8 mm RMT 18599.00
iii) 8.8 mm RMT 20438.00
iv) 10 mm RMT 23190.00

56 PIPES /FITTINGS/ SPECIALS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

v) 11 mm RMT 25478.00
vi) 12.5 mm RMT 28898.00
vii) 14.2 mm RMT 32758.00
K Outer dia of pipe 914 mm and thickness
i) 8 mm RMT 20932.00
ii) 8.8 mm RMT 23005.00
iii) 10 mm RMT 26107.00
iv) 11 mm RMT 28686.00
v) 12.5 mm RMT 32544.00
vi) 12 mm RMT 31260.00
vii) 14.2 mm RMT 36900.00
L Outer dia of pipe 1016 mm and thickness
i) 8.8 mm RMT 25597.00
ii) 10 mm RMT 29053.00
iii) 11 mm RMT 31927.00
iv) 12.5 mm RMT 36226.00
v) 12 mm RMT 34794.00
vi) 14.2 mm RMT 41083.00
vii) 16 mm RMT 46208.00
M Outer dia of pipe 1067 mm and thickness
i) 8.8 mm RMT 26893.00
ii) 10 mm RMT 30526.00
iii) 11 mm RMT 33547.00
iv) 12.5 mm RMT 38067.00
v) 12 mm RMT 36562.00
vi) 14.2 mm RMT 43175.00
vii) 16 mm RMT 48564.00
N Outer dia of pipe 1118 mm and thickness
i) 8.8 mm RMT 28189.00
ii) 10 mm RMT 31999.00
iii) 11 mm RMT 35167.00
iv) 12.5 mm RMT 39908.00
v) 12 mm RMT 38329.00
vi) 14.2 mm RMT 45266.00
vii) 16 mm RMT 50921.00
O Outer dia of pipe 1219 mm and thickness
i) 10 mm RMT 34916.00
ii) 11 mm RMT 38375.00
iii) 12.5 mm RMT 43554.00
iv) 14.2 mm RMT 49408.00
v) 16 mm RMT 55588.00
vi) 17.5 mm RMT 60723.00
P Outer dia of pipe 1321 mm and thickness RMT
i) 12.5 mm 47237.00
ii) 14.2 mm RMT 53591.00
iii) 16 mm RMT 60301.00
iv) 17.5 mm RMT 65878.00
v) 20 mm RMT 75145.00
Q Outer dia of pipe 1422 mm and thickness
i) 12.5 mm RMT 50883.00
ii) 14.2 mm RMT 57733.00
iii) 16 mm RMT 64968.00

57 PIPES /FITTINGS/ SPECIALS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

iv) 17.5 mm RMT 70983.00

v) 20 mm RMT 80979.00
R Outer dia of pipe 1524 mm and thickness
i) 14.2 mm RMT 61916.00
ii) 16 mm RMT 69681.00
iii) 17.5 mm RMT 76138.00
iv) 20 mm RMT 86870.00
v) 22.2 mm RMT 96285.00
S Outer dia of pipe 1626 mm and thickness
i) 14.2 mm RMT 66099.00
ii) 16 mm RMT 74394.00
iii) 17.5 mm RMT 81293.00
iv) 20 mm RMT 92762.00
v) 22.2 mm RMT 102825.00
T Outer dia of pipe 1727 mm and thickness
i) 14.2 mm RMT 70241.00
ii) 16 mm RMT 79061.00
iii) 17.5 mm RMT 86398.00
iv) 20 mm RMT 98596.00
v) 22.2 mm RMT 109300.00
U Outer dia of pipe 1829 mm and thickness
i) 14.2 mm RMT 74424.00
ii) 16 mm RMT 83775.00
iii) 17.5 mm RMT 91553.00
iv) 20 mm RMT 104487.00
v) 22.2 mm RMT 115840.00
V Outer dia of pipe 2032 mm and thickness
i) 16 mm RMT 93155.00
ii) 17.5 mm RMT 101812.00
iii) 20 mm RMT 116212.00
iv) 22.2 mm RMT 128855.00
v) 25 mm RMT 144904.00
W Outer dia of pipe 2235 mm and thickness
i) 17.5 mm RMT 112072.00
ii) 20 mm RMT 127938.00
iii) 22.2 mm RMT 141870.00
iv) 25 mm RMT 159561.00
X Outer dia of pipe 2540 mm and thickness
i) 20 mm RMT 145554.00
ii) 22.2 mm RMT 161424.00
iii) 25 mm RMT 181582.00
3.2 Providing and fixing of flanged/ plain ended MS specials made from MS sheet strips
of relavant IS specification of approved thickness by welding, lowering, laying,
aligning, fixing in position at all level/ depths in trenches complete including all
taxes, material, labour, inside lining, outside coating, testing and commisssioning
along with pipe line as per technical specifications and direction of Engineer in
Charge.
3.2.1 MS pipe specials up to 600 mm dia (with minimum 5mm thickness sheet) Kg 126.00
3.2.2 MS pipe specials up to 600 mm dia (with minimum 6.3 mm thickness sheet) Kg 134.00

58 PIPES /FITTINGS/ SPECIALS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

Lining and Coating of MS Pipe

3.3 Providing and applying 3 LPE (3 Layer Polyethylene) coating conforming to ISO SQM 1227.00
21809-1 , DIN 30670-91 , ANSI/AWWA C2 l3-01 or CAN/CSA Z245.20-10 to
external surface of M.S. Pipe comprising of a layer of fusion bonded epoxy (FBE),
overlaid with PE adhesive coat with an outer layer of high density polyethylene,
including preparation of surface by solvent cleaning as per ISO 8502 3, abrasive
blasting to a surface finish of Grade SA 2.5 to DIN EN ISO 8501 - 1 and surface
profile of 50 to 75 microns as per DIN EN ISO 8503-2. Minimum thickness of FBE
shall be 200 microns and of adhesive layer shall be 200-250 microns including field
joints coating at site complete as per technical specification and direction of Engineer
in Charge.
Note:(i) 3LPE external surface coating on MS pipes shall be factory applied only.
(ii) Rates are for total thickness of 3LPE coating system as per DIN 30670-Table-3
(a) For pipe dia. Up to 500 mm and less than 800 mm minimum thickness of coating
system 2.5-3.2 mm
(b)For pipe dia. equal and more than 800 mm minimum thickness of coating system
3.2-3.7 mm
3.4 Providing and applying DFBE (Dual Layer Fusion Bonded Epoxy) Coating to the SQM 954.00
external surface of M.S. Pipes conforming to Canadian Standard CSA Z 245.20-10,
consisting of Ist layer of (FBE) Fusion Bonded Epoxy as corrosion protection layer
and 2nd layer also of FBE powder as Abrasion Resistant Overcoat (ARO), including
preparation of surface by cleaning as per ISO 8502-3 and abrasive blasting to a finish
to SA 2.5 of Swedish standard SIS 055900 (latest edition) and anchor pattern of 75 to
100 microns including field joints coating at site complete as per technical
specification and direction of Engineer in Charge.
Note:
(i) DFBE external surface coating on MS pipes shall be factory applied only.
(ii) Minimum thickness of I layer of FBE shall be 350 microns and of II layer of ARO
shall be 400 microns (i.e. total thickness of 750 microns) with tolerance of+ I00
microns
3.5 Providing and applying Spray applied, 100% Solids (Solvent free) Two Component SQM 852.00
PU ( Polyurethane) coating as per AWWA C222 Standard on external surface of M.S.
Pipe including preparation of pipe outer surface as per SSPC-SPIO/NACE No 2 near
white blast cleaning. Anchor profile obtained shall be more than 75 microns,
including field joints coating at site complete as per technical specification and
direction of Engineer in Charge.
Note:
(i) PU external surface coating on MS pipes shall be factory applied only.
(ii) Rates are for single coat of PU of thickness 625 microns.

3.6 Providing and applying with mechanical arrangement I :3 proportion cement sand SQM
gunite of following thickness to M.S. Pipe surface under 2.1 Kg per Sqcm to 2.80 Kg
per Sqcm. pressure including removing the loose materials as directed by EiC and
including scrapping the surface with wire brushes, degreasing, cleaning by
compressed air and providing fixing BRC fabric no.14 as reinforcement, curing for 21
days, disposing off the rebound materials with in a lead of 50 mtr including field
joints coating at site complete as per technical specification and direction of Engineer
in Charge.
3.6.1 25 mm thick SQM 545.00
3.6.2 40 mm thick SQM 613.00

59 PIPES /FITTINGS/ SPECIALS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

3.7 Providing and applying Solvent free, two pack liquid epoxy lining to internal surface SQM 568.00
of M.S. Pipe as per BS 6920:2000 and AWWA C2 I0 standard including preparation
of internal surface of pipe by cleaning as per ISO 8502-3 and abrasive blasting to a
surface finish to SA 2.5 to DIN, ISO 8501-1 and surface profile of 50 to 75 microns as
per DIN-ISO 8503-4, including field joints coating at site complete as per technical
specification and direction of Engineer in Charge. Liquid Epoxy shall be NSF/WRAS
approved for drinking water.
Note:
(i) Liquid epoxy lining on internal surface of MS pipe shall be factory applied only.
(ii) Dry Film Thickness (DFT) shall be minimum 406 microns with tolerance +200 & -
0 microns.

3.8 Providing and applying I00% Solids,Rigid, DTM Polyurethane Coating co internal SQM 603.00
surface of M.S. Pipe as per AWWA C222 standard including preparation of internal
surface of pipe as per SSPC-SPl O/NACE No 2 near white blast cleaning. Anchor
profile shall be more than 75 microns including field joints coating at site complete as
per technical specification and direction of Engineer in Charge. Polyurethane Coating
shall be NSF/WRAS/SS-375 approved for drinking water.
Note:
(i) PU internal lining on MS pipe shall be factory applied.
(ii) Rates are for single coat of PU of thickness 500 microns

3.9 Providing and making inner cement mortar lining to M.S. Pipes with mechanical
devices in cement mortar 1: 1 proportion, including cost of all materials, labour,
special sand required. machinery, power generation, all equipments, including field
joints at site complete as per technical specification and direction of Engineer in
3.9.1 9charge.
mm thick for pipes upto 700 mm dia SQM 307.00
3.9.2 12 mm thick for pipes above 700 mm dia SQM 341.00

4.0 BWSC PIPES

4.1 Providing, lowering, laying and jointing in trenches bar wrapped steel cylinder pipes
(BWSC) for overlapping steel welded joint as per IS: 15155-2001(amended up to
date) of following class and diameter including all taxes including all taxes(central
and local), transportation and freight charges, inspection charges, loading/unloading
charges stacking of pipes including cost of labour and metrial special (T-bend etc.)
satisfactorily hydraulic testing, disinfection etc complete as per technical specification
and direction of engineer incharge (excluding earthwork) ; with E.D. exemption.
Note--Providing and fixing of all requisite specials as per drawing, design and layout
are inclusive in RM measurement of the item and shall not be paid separately.
NOTES
1) Class mentioned below represents the factory test pressure of pipe,
2) For external coating at site to the joints, necessary polythene wrapping for pouring
cement slurry shall also be provided with each pipe.
2
4.1.1 Factory test pressure 12 Kg /Cm
i) 250 mm RMT 3625.00
ii) 300 mm RMT 4128.00
iii) 350 mm RMT 4625.00
iv) 400 mm RMT 5296.00
v) 450 mm RMT 6112.00
vi) 500 mm RMT 6614.00
vii) 600 mm RMT 8494.00
viii) 700 mm RMT 10924.00
ix) 800 mm RMT 13396.00
x) 900 mm RMT 16196.00

60 PIPES /FITTINGS/ SPECIALS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

xi) 1000 mm RMT 19487.00

xii) 1100 mm RMT 26823.00
xiii) 1200 mm RMT 29755.00
xiv) 1300 mm RMT 32526.00
xv) 1400 mm RMT 36266.00
xvi) 1500 mm RMT 43074.00
xvii) 1600 mm RMT 45863.00
2
4.1.2 Factory test pressure 14Kg /Cm
i) 250 mm RMT 3629.00
ii) 300 mm RMT 4136.00
iii) 350 mm RMT 4628.00
iv) 400 mm RMT 5310.00
v) 450 mm RMT 6125.00
vi) 500 mm RMT 6791.00
vii) 600 mm RMT 8861.00
viii) 700 mm RMT 12167.00
ix) 800 mm RMT 14894.00
x) 900 mm RMT 18058.00
xi) 1000 mm RMT 22907.00
xii) 1100 mm RMT 26893.00
xiii) 1200 mm RMT 30827.00
xiv) 1300 mm RMT 35143.00
xv) 1400 mm RMT 40568.00
xvi) 1500 mm RMT 50896.00
xvii) 1600 mm RMT 53428.00
2
4.1.3 Factory test pressure 16 Kg /Cm
i) 250 mm RMT 3634.00
ii) 300 mm RMT 4147.00
iii) 350 mm RMT 4634.00
iv) 400 mm RMT 5326.00
v) 450 mm RMT 6208.00
vi) 500 mm RMT 7226.00
vii) 600 mm RMT 9445.00
viii) 700 mm RMT 13045.00
ix) 800 mm RMT 15032.00
x) 900 mm RMT 19473.00
xi) 1000 mm RMT 23542.00
xii) 1100 mm RMT 28613.00
xiii) 1200 mm RMT 33257.00
xiv) 1300 mm RMT 38284.00
xv) 1400 mm RMT 44125.00
xvi) 1500 mm RMT 52378.00
xvii) 1600 mm RMT 57681.00
2
4.1.4 Factory test pressure 18 Kg /Cm
i) 250 mm RMT 3640.00
ii) 300 mm RMT 4158.00
iii) 350 mm RMT 4639.00
iv) 400 mm RMT 5391.00
v) 450 mm RMT 6561.00
vi) 500 mm RMT 7645.00
vii) 600 mm RMT 10068.00

61 PIPES /FITTINGS/ SPECIALS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

viii) 700 mm RMT 13929.00

ix) 800 mm RMT 16183.00
x) 900 mm RMT 20882.00
xi) 1000 mm RMT 25488.00
xii) 1100 mm RMT 30693.00
xiii) 1200 mm RMT 35785.00
xiv) 1300 mm RMT 41116.00
xv) 1400 mm RMT 47889.00
xvi) 1500 mm RMT 56112.00
xvii) 1600 mm RMT 62525.00
2
4.1.5 Factory test pressure 20 Kg /Cm
i) 250 mm RMT 3645.00
ii) 300 mm RMT 4171.00
iii) 350 mm RMT 4702.00
iv) 400 mm RMT 5759.00
v) 450 mm RMT 7009.00
vi) 500 mm RMT 8237.00
vii) 600 mm RMT 10846.00
viii) 700 mm RMT 15107.00
ix) 800 mm RMT 18899.00
x) 900 mm RMT 22907.00
xi) 1000 mm RMT 28172.00
xii) 1100 mm RMT 33672.00
xiii) 1200 mm RMT 39272.00
xiv) 1300 mm RMT 45253.00
xv) 1400 mm RMT 53001.00
xvi) 1500 mm RMT 62765.00
xvii) 1600 mm RMT 68949.00
5.0 Providing, lowering, laying and jointing in trenches, standard lengths ISI marked AC
pressure pipe class 15 manufactured by MAZZA process as per lS-1592-2003 or
amended upto date with AC coupling and EPDM Rubber sealing rings of Type -3 as
per IS: 5382/1985 (Reaffirmed 1998) or amended up to date, including all taxes ,
transportation and freight charges, inspection charges, loading/ unloading charges,
stacking of pipes, labour and material, satisfactory hydraulic testing etc. complete as
per technical specifications and direction of Engineer-in-charge. (excluding earth
work and specials)
5.1 100 mm dia Cl-15 RM 456.50
5.2 125 mm dia Cl-15 RM 583.00
5.3 150 mm dia Cl-15 RM 727.00
5.4 200 mm dia Cl-15 RM 1183.00
5.5 250mm dia Cl-15 RM 1629.00
5.6 300 mm dia Cl-15 RM 2358.00
5.7 350 mm dia Cl-15 RM 3117.00
5.8 400 mm dia Cl-15 RM 4125.00
5.9 450 mm dia Cl-15 RM 4846.00
5.10 500 mm dia Cl-15 RM 6136.00
5.11 600 mm dia Cl-15 RM 8745.00
5.12 700 mm dia Cl-15 RM 11231.00
5.13 800 mm dia Cl-15 RM 15290.00
5.14 900 mm dia Cl-15 RM 19250.00
5.15 1000 mm dia Cl-15 RM 23210.00

62 PIPES /FITTINGS/ SPECIALS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

6.0 Removing and Laying of Pipe line

6.1 De-jointing and removing of already laid Cl/DI pipes of following diameters in
excavated trenches with care, without damaging pipes, CID joints, valves, specials
etc. and other materials and then refilling of soil after de-laying and de-jointing of
pipelines 1.17 with proper compaction and disposing of all surplus soil as directed
with in a lead of 30 mtr. This also include stacking the pipes with care and
transporting the same to div./sub div. store or as directed by EiC with in the division.
(Rates are Exclusive of Earth Work)
6.1.1 80 mm RMT 45.00
6.1.2 100 mm RMT 50.00
6.1.3 125 mm RMT 50.00
6.1.4 150 mm RMT 59.00
6.1.5 200 mm RMT 79.00
6.1.6 250 mm RMT 98.00
6.1.7 300 mm RMT 119.00
6.1.8 350mm RMT 134.00
6.1.9 400 mm RMT 164.00
6.1.10 450 mm RMT 200.00
6.1.11 500 mm RMT 257.00
6.1.12 600 mm RMT 309.00
6.2 De-jointing and removing of already laid MS pipes of following diameters in
excavated trenches with care, without damaging pipes, CID joints, valves, specials
etc. and other materials and then refilling of soil after de-laying and de-jointing of
pipelines with proper 1.18 compection and disposing of all surplus soil as directed
with in a lead of 30 mtr. This also include stacking the pipes with care and
transporting the same to div./sub div. store or as directed by EiC with in the division.
(Rates are Exclusive of Earth Work and jointing material)
6.2.1 100 mm RMT 36.00
6.2.2 125 mm RMT 36.00
6.2.3 150 mm RMT 42.00
6.2.4 200 mm RMT 80.00
6.2.5 250 mm RMT 99.00
6.2.6 300 mm RMT 120.00
6.2.7 350mm RMT 141.00
6.2.8 400 mm RMT 162.00
6.2.9 450 mm RMT 208.00
6.2.10 500 mm RMT 251.00
6.2.11 600 mm RMT 303.00
6.3 Laying, Jointing, Testing and Commissioning of Ductile Iron(DI) Pipes of any
class in assorted length with specials, valves etc. as per satisfaction of EiC, including
local handling and transportation . (Rates are Exclusive of Earth Work and
jointing materials)
6.3.1 80 mm RMT 63.00
6.3.2 100 mm RMT 63.00
6.3.3 125 mm RMT 66.00
6.3.4 150 mm RMT 81.00
6.3.5 200 mm RMT 97.00
6.3.6 250 mm RMT 115.00
6.3.7 300 mm RMT 138.00
6.3.8 350mm RMT 161.00
6.3.9 400 mm RMT 195.00
6.3.10 450 mm RMT 234.00

63 PIPES /FITTINGS/ SPECIALS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

6.3.11 500 mm RMT 296.00

6.3.12 600 mm RMT 354.00
6.4 Laying, Jointing, Testing and Commissioning of AC PressurePipes (Class-
10/15/20) of any class in assorted length with specials, valves etc. including local
handling and transportation and as per satisfaction of EiC. (Rates are Exclusive of
Earth Work and jointing materials)
6.4.1 80 mm RMT 32.00
6.4.2 100 mm RMT 34.00
6.4.3 125 mm RMT 37.00
6.4.4 150 mm RMT 40.00
6.4.5 200 mm RMT 47.00
6.4.6 250 mm RMT 52.00
6.4.7 300 mm RMT 98.00
6.4.8 350mm RMT 106.00
6.4.9 400 mm RMT 121.00
6.4.10 450 mm RMT 139.00
6.4.11 500 mm RMT 158.00
6.4.12 600 mm RMT 162.00
6.5 Laying, Jointing, Testing and Commissioning of HDPE pipes of any grade in
assorted length with specials, valves etc. with jointing material/ fixing of necessary
jointing material like mechenical connector i.e. thread/ insert joint/ quick release
coupler joint compresion fitting joint or flanged joint and jointing pipe in proper
position jointing of all specials by butt fusion I electro fusion welding method,
including local handling and transportation and as per satisfaction of EiC. (Rates are
Exclusive of Earth Work and jointing materials)
6.5.1 63 mm RMT 10.35
6.5.2 75 mm RMT 16.10
6.5.3 90 mm RMT 24.15
6.5.4 110 mm RMT 36.80
6.5.5 125 mm RMT 43.70
6.5.6 140 mm RMT 49.45
6.5.7 160 mm RMT 83.95
6.5.8 180 mm RMT 89.70
6.5.9 200 mm RMT 94.30
6.5.10 225 mm RMT 97.75
6.5.11 250mm RMT 120.75
6.5.12 280mm RMT 128.80
6.5.13 315mm RMT 138.00
6.6 Providing, lowering, laying, aligning, fixing in position and jointing at all level/
depths DI standard specials with rubber ring (EPDM)/ nut bolt and insertion sheet and
jointing as per IS: 9523-2000 or as amended up to date, such as tees, bends, tapers,
caps etc. within trenches in DI pipe line complete including all material, labour, taxes,
testing and commissioning along with pipe line as per technical specifications and
direction of Engineer-in-charge (excluding earth work).
6.6.1 All End Socketed
6.6.1.1 Up to 300 mm Diameter Kg 145.00
6.6.1.2 Above 300mm and up to 600 mm diameter Kg 161.00
6.6.1.3 Above 600 mm diameter Kg 207.00

64 PIPES /FITTINGS/ SPECIALS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

6.6.2 All End Flanged

6.6.2.1 Up to 300 mm Diameter Kg 158.00
6.6.2.2 Above 300mm and up to 600 mm diameter Kg 179.00
6.6.2.3 Above 600 mm diameter Kg 235.00
6.6.3 Single Flange/ MJ Collar
6.6.3.1 Up to 300 mm Diameter Kg 151.00
6.6.3.2 Above 300mm and up to 600 mm diameter Kg 168.00
6.6.3.3 Above 600 mm diameter Kg 219.00
6.6.4 Double Flange Pipe (up to 1 mtr. length)
6.6.4.1 Up to 300 mm Diameter Kg 167.00
6.6.4.2 Above 300mm and up to 600 mm diameter Kg 195.00
6.6.4.3 Above 600 mm diameter Kg 246.00

65 PIPES /FITTINGS/ SPECIALS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER - XIV
MICRO IRRIGATION

General Condition

1 The rates are inclusive of all taxes, levies, royalty, GST, leads of all material and contractor's profit etc.

2 The pipe of respective pressure rating is allowed only up to 80% of permissible pressure as per IS
standards.
3 All the pipe network should be designed in such manner that the total head losss (including frictional head
loss, fitting losses and elveation differance excluding suction head, losses of filteration unit and pump
house losses ) for a Chak of size up to 200 Ha should not be more than 45 m and for chak of size 200 to
400 Ha should not be more than 50 meter. However, if topography of a particular chak doesn’t permit the
same than for a particular chak engineer-in-charge may permit more head loss.

4 Items for different water allowances 2.50, 3, 4 or 5 cusec / 1000 acre are to be taken in estimate with the
prior approval from competent authority.

5 The rates in this chapter are inclusive of de-watering wherever required.

Rate in
S.No Item Unit
Rs
PLANNING AND DESIGNING
1 Collection of revenue map and jamabandi of the Area of Interest, scanning revenue map / Ha 56
and digitization of khasra boundary & jamabandi.
Rate shall be paid per Ha GCA
2 Geo-refrencing of digitized khasra map and marking chak & sub chak of required size for / Ha 57
micro irrigation and providing chak & sub chak wise GCA, CCA details in excel format.
Soft copy with two set of Hard copy shall be provided.
Rate shall be paid per Ha CCA

3 Planning of field distribution pipe network up to chak and sub chak level, hydraulic design / Ha 104
of pipe network planning & design of outlet arrangement with drawing and Irrigation
scheduling up to chak level. Chak Plan showing pipe network is to be provided in soft copy
& two set of Hard copy.
Rate shall be paid per Ha CCA
4 Preparation of l-section of pipe lines as per approved pipe network & hydraulic design / Ha 135
from competent authority (showing safety valve & control valve arrangement, filteration
system and other accessory if required). Design and drawing of thrust blocks, pedestals and
valve chamber, are to be provided. All design, drawing should fulfill the design
specification as per the tender document and IS code / relevant mannuals.
Rate shall be paid per Ha CCA

5 Irrigation scheduling with timing up to subchak level is to be preapred as per approved / Ha 46

design and revenue record. Rate shall be paid per Ha CCA

6 Planning and design of Diggie for micro irrigation system including design of intake/ sump Each 85000
well, pump house and other ancillary developments to be done in the campus and
providing all hydro- electro mechanical designs and drawings.

66 MICRO IRRIGATION
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

A FIELD DISTRIBUTION PIPE NETWORK Unit Rate in

Water allowance has been taken 3.0 cusec / 1000 acre Rs
1 Supplying, laying, jointing, testing and commissioning of buried HDPE, PE 100 grade / Ha 44200
pipe net work system in the chak upto Hydrant (chak size up to 200 Ha and sub chak 4.5
Ha and Hydrant at every 1.25 Ha to 1.5 Ha) including fittings/ specials as per approved
design & drawings and fulfilling IS code / mannuals specification. This item includes
excavation, refilling, ramming and disposal of extra excavated material. This item is for
water allowance @ 3 cusec / 1000 acre and pipe line terminating at Hydrant is to be
designed to carry minimum 3.5 lps discharge and 20 meter head.
The rates are inclusive of material, lead & lift and also inclusive of all kind of taxes, levies,
turnover tax, service tax, octroi, vat, panchayat tax, royalty, GST & contractor profit.
Note: This is including cost of supply & fixing of manual operated Hydrant- outlet
assembly as per the respective item, but excluding cost of safety valves, control valves and
metering arrangements.

2 Supplying, laying, jointing, testing and commissioning of buried HDPE PE 100 grade pipe / Ha 40200
net work system in the chak upto Hydrant (Chak size up to 200 Ha and sub chak at every
4.5 Ha and hydrant at every 2.0 Ha to 2.5 Ha) including fittings/ specials as per approved
design & drawings and fulfilling IS code / mannuals specification. This item is including
excavation, refilling, ramming and disposal of extra excavated material. This item is for
water allowance @ 3 cusec / 1000 acre and pipe line terminating at Hydrant is to be
designed to carry minimum 3.5 lps discharge and 20 m head.
The rates are inclusive of material, lead & lift and also inclusive of all kind of taxes, levies,
turnover tax, service tax, octroi, vat, panchayat tax, royalty, GST & contractor profit.
Note: This is including cost of supply & fixing of manual operated Hydrant- outlet
assembly as per the respective item, but excluding cost of safety valves, control valves and
metering arrangements.

3 Supplying, laying, jointing, testing and commissioning of buried HDPE PE 100 grade pipe / Ha 33300
net work system in the chak upto Hydrant (Chak size up to 200 Ha and sub chak with
hydrant at every 4.0 Ha to 5.0 Ha) including fittings/ specials as per approved design &
drawings and fulfilling IS code / mannuals specification. This item is including excavation,
refilling, ramming and disposal of extra excavated material. This item is for water
allowance @ 3 cusec / 1000 acre and pipe line terminating at Hydrant is to be designed to
carry minimum 3.75 lps discharge and Head 22 meter.
The rates are inclusive of material, lead & lift and also inclusive of all kind of taxes, levies,
turnover tax, service tax, octroi, vat, panchayat tax, royalty, GST & contractor profit.
Note: This is including cost of supply & fixing of manual operated Hydrant- outlet
assembly as per the respective item, but excluding cost of safety valves, control valves and
metering arrangements.
4 Supplying, laying, jointing, testing and commissioning of buried HDPE PE 100 pipe grade / Ha 26000
net work system within the chak upto Hydrant (Chak size of 201 to 400 Ha and sub chak at
every 8.0 Ha to 8.5 Ha) including fittings/ specials as per approved design & drawings
and fulfilling IS code / mannuals specification. This item is including excavation, refilling,
ramming and disposal of extra excavated material.
This item is for water allowance @ 3 cusec / 1000 acre and pipe line terminating at
Hydrant is to be designed to carry minimum 5 lps discharge and Head 25 meter.
The rates are inclusive of material, lead & lift and also inclusive of all kind of taxes, levies,
turnover tax, service tax, income tax, octroi, vat, panchayat tax, royalty, GST & contractor
profit.
Note: This is including cost of supply & fixing of manual operated Hydrant- outlet
assembly as per the respective item, but excluding cost of safety valves, control valves and
metering arrangements.

67 MICRO IRRIGATION
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

B FIELD DISTRIBUTION PIPE NETWORK

Water allowance has been taken 2.5 cusec / 1000 acre
1 Supplying, laying, jointing, testing and commissioning of buried HDPE PE 100 grade pipe / Ha 38400
net work system within the chak upto Hydrant (chak size up to 200 Ha and sub chak 4.5
HA and Hydrant at every 1.25 Ha to 1.5 Ha) including fittings as per approved design &
drawings and fulfilling IS code / mannuals specification. This item is including excavation,
refilling, ramming and disposal of extra excavated material. This item is for water
allowance @ 2.5 cusec / 1000 acre and pipe line terminating at Hydrant is to be designed to
carry minimum 3.5 lps discharge and 20 M head.
The rates are inclusive of material, lead & lift and also inclusive of all kind of taxes, levies,
turnover tax, service tax, income tax, octroi, vat, panchayat tax, royalty, GST & contractor
profit.
Note: This is including cost of supply & fixing of manual operated Hydrant- outlet
assembly as per the respective item, but excluding cost of safety valves, control valves and
metering arrangements.
2 Supplying, laying, jointing, testing and commissioning of buried HDPE PE 100 grade pipe / Ha 35600
net work system within the chak upto Hydrant (Chak size up to 200 Ha and sub chak at
every 4.5 Ha and hydrant at every 2.0 Ha to 2.5 Ha) including fittings as per approved
design & drawings and fulfilling IS code / mannuals specification. This item is including
excavation, refilling, ramming and disposal of extra excavated material. This item is for
water allowance @ 2.5 cusec / 1000 acre and pipe line terminating at Hydrant is to be
designed to carry minimum 3.5 lps discharge and 20 m head.
The rates are inclusive of material, lead & lift and also inclusive of all kind of taxes, levies,
turnover tax, service tax, income tax, octroi, vat, panchayat tax, royalty, GST & contractor
profit.
Note: This is including cost of supply & fixing of manual operated Hydrant- outlet
assembly as per the respective item, but excluding cost of safety valves, control valves and
metering arrangements.
3 Supplying, laying, jointing, testing and commissioning of buried HDPE PE 100 grade pipe / Ha 28700
net work system within the chak upto Hydrant (Chak size up to 200 Ha and sub chak with
hydrant at every 4.0 Ha to 5.0 Ha) including fittings as per approved design & drawings
and fulfilling IS code / mannuals specification. This item is for water allowance @ 2.5
cusec / 1000 acre and pipe line terminating at Hydrant is to be designed to carry minimum
3.75 lps discharge and Head 22 m.
The rates are inclusive of material, lead & lift and also inclusive of all kind of taxes, levies,
turnover tax, service tax, income tax, octroi, vat, panchayat tax, royalty, GST & contractor
profit.
Note: This is including cost of supply & fixing of manual operated Hydrant- outlet
assembly as per the respective item, but excluding cost of safety valves, control valves and
metering arrangements.
Supplying, laying, jointing, testing and commissioning of buried HDPE PE 100 grade pipe / Ha 22500
net work within the chak upto Hydrant (Chak size of 350-400 Ha and sub chak at every 8.0
Ha to 8.5 Ha) including fittings as per approved design & drawings and fulfilling IS code /
mannuals specification. This item is including excavation, refilling, ramming and disposal
of extra excavated material.
This item is for water allowance @ 2.5 cusec / 1000 acre and pipe line terminating at
Hydrant is to be designed to carry minimum 5 lps discharge and Head 25 m.
The rates are inclusive of material, lead & lift and also inclusive of all kind of taxes, levies,
turnover tax, service tax, income tax, octroi, vat, panchayat tax, royalty, GST & contractor
profit.
Note: This is including cost of supply & fixing of manual operated Hydrant- outlet
assembly as per the respective item, but excluding cost of safety valves, control valves and
metering arrangements.

68 MICRO IRRIGATION
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

C FIELD DISTRIBUTION PIPE NETWORK

Water allowance has been taken 4 cusec / 1000 acre
1 Supplying, laying, jointing, testing and commissioning of buried HDPE PE 100 grade, pipe / Ha 58856
net work within the chak upto Hydrant (Av. chak size up to 200 Ha, sub chak 12.5-15.0 Ha
and Hydrant at every 1.25 Ha to 1.5 Ha) including fittings / specials as per approved design
& drawings and fulfilling IS code/mannuals specification. This item is including
excavation, refilling, ramming and disposal of extra excavated material. This item is for
water allowance @ 4.0 cusec / 1000 acre and pipe line terminating at Hydrant emanating
water @ 20 meter head.
The rates are inclusive of material, lead & lift and also inclusive of all kind of taxes, levies,
turnover tax, service tax, income tax, octroi, vat, panchayat tax, royalty, GST & contractor
profit.
Note: This is including cost of supply & fixing of manual operated Hydrant- outlet
assembly as per the respective item, but excluding cost of safety valves, control valves and
metering arrangements.
D FIELD DISTRIBUTION PIPE NETWORK
Water allowance has been taken 5 cusec / 1000 acre

1 Supplying, laying, jointing, testing and commissioning of buried HDPE PE 100 grade pipe / Ha 65570
net work within the chak upto Hydrant (Av. chak size up to 200 Ha and sub chak 12.5-
15.0 Ha and Hydrant at every 1.25 Ha to 1.5 Ha) including fittings / specials as per
approved design & drawings and fulfilling IS code / mannuals specification. This item is
including excavation, refilling, ramming and disposal of extra excavated material. This
item is for water allowance @ 5.0 cusec / 1000 acre and pipe line terminating at Hydrant
emanating water @ 20 meter head.
The rates are inclusive of material, lead & lift and also inclusive of all kind of taxes, levies,
turnover tax, service tax, income tax, octroi, vat, panchayat tax, royalty, GST & contractor
profit.
Note: This is including cost of supply & fixing of manual operated Hydrant- outlet
assembly as per the respective item, but excluding cost of safety valves, control valves and
metering arrangements.

CONTROL VALVES
1 Supplying, laying, jointing, testing and commissioning of Pilot operated SCADA
Compatible Diaphragm Type Pressure Reducing Valves (Class PN 1.6) for different
pipe sizes as under;
80 mm dia Each 120540
100 mm dia Each 132927
125 mm dia Each 162269
150 mm dia Each 180581
200 mm dia Each 224639
250 mm dia Each 308094
300 mm dia Each 404413
2 Supplying, laying, jointing, testing and commissioning of Diaphragm Type Flow Control
Valve With Electrical Actuator suitable for SCADA (PN 1.6 ) for different pipe sizes as
under;
80 mm dia Each 113798
100 mm dia Each 128639
125 mm dia Each 140144
150 mm dia Each 157086
200 mm dia Each 189135
250 mm dia Each 276791
300 mm dia Each 377516

69 MICRO IRRIGATION
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

SAFETY VALVES & CONTROL VALVES

1 Supplying, laying, jointing, testing and commissioning of safety valve i.e air valve, NRV, Rs @ 5% of
PRV, scour valve, check valve, butterfly valve, sluice valve, gate valve, ball valve,
dismentalling joint etc. essential for safety and smooth operation of pipe network. This also cost of pipe
include the civil work for installation, safety and ease of operation of valves.
network
2 Supplying, laying, jointing, testing and commissioning of motor operated pressure Rs @ 8% of
reducing flow control valve (elctro megnatic type) up to chak level excluding battery cost of pipe
backup or electric supply line for different pipe sizes as under; network
FILTERATION ARRANGEMENT
PRIMARY FILTERATION
1 Supplying, laying, jointing, testing and commissioning of Hydrocyclon filter for primary / Ha 2000
filteration up to particle size of 300 micron with dismentalling joint and all other
accessories required for proper functioning for discharge capacityies as under;
SECONDARY FILTERATION
2 Supplying, laying, jointing, testing and commissioning of auto clean screen / disc filter
having interconnecting manifold between filters in high quality MS pipe as per relevent IS
standard, duly fabricated & external surface duly epoxy painted to 150DFT including DP
switch and controller and battery backup. Providing and fixing Inlet, Outlet, Bypass
Butterfly Isolation valves & Check valve in CI, PN10 Wafer type and counter flanges in
ANSI B 16.5# 150 for discharge capacity as under;

35 LPS to 55 LPS each 695000

PLC-SACDA CONTROL
Supplying, designing and installation of PLC- SCADA system with all parts and GPRS
based transmission system (RTU) for operation of pipe irrigation network as per designed
irrigation scheduling up to Chak / Sub-Chak Level
1 With SCADA contorl up to 200 Ha Chak Lvel / ha 6000
2 With SCADA contorl up to 20 Ha sub-Chak Lvel and hydrant up to 1.25-1.5ha / ha 9500
3 With SCADA contorl up to 30 ha sub-Chak Lvel and hydrant up to 1.25-1.5 ha / ha 8000
NOTE:-
For estimation of different component of micro irrigation work "Turnkey Project on EPC mode" following
provision can be considered as per design / specification finalised for the scheme;
1 Cost of hydro electro mechanical works including pumps, motors, mud pumps, trash rack, screens, all
valve arrangement, flow / pressure meter, water level recorder, control panel within the pump house and
supply & installation of transformer (with one standby) etc. can be taken @ Rs 25000 per kw of capacity of
total pumps (including standby capacity). This is excluding the cost of electric transmission line from GSS
/ Grid to the pump house.
2 Filteration system
(a) Cost of primary filteration (if required) including siltation chamber, hydrocyclone filter with isolation
valve & manifold etc. arrangement, cost estimate can be prepared or it can be taken @ Rs 2000 per Ha
CCA for estimation purpose only. Primary filteration can filter material up to 200 micron particles.
(b) Cost of secondary filteration system including auto clean screen / disc filter having interconnecting
manifold between filters in high quality MS pipe as per relevent IS standard, duly fabricated & external
surface duly epoxy painted to 150DFT including DP switch and controller and battery backup. Providing
and fixing Inlet, Outlet, Bypass Butterfly Isolation valves & Check valve in CI, PN10 Wafer type and
counter flanges in ANSI B 16.5# 150 for designed discharge cost estimate can be prepared or it can be
taken @ Rs 4000 per Ha CCA for estimation purpose only. Secondary filteration for micro irrigation is
required to filter particle size up to 130 micron.

70 MICRO IRRIGATION
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

3 Cost for supplying, laying, jointing, testing and commissioning of safety valve i.e air valve, NRV, PRV,
scour valve, check valve, butterfly valve, sluice valve, gate valve, ball valve, dismentalling joint etc.
essential for safety and smooth operation of pipe network including civil work (pedestal,valve chamber
etc.) is to assesed from detailed sample estimate.
4 Cost for supplying, laying, jointing, testing and commissioning of motor operated pressure reducing flow
control valve (elctro megnatic / anaolg type) up to chak level excluding / including battery backup or
electric supply line for different pipe sizes is to assesed from detailed sample estimate.

5 Cost for supplying, designing and installation of PLC- SCADA system with all parts and GPRS based
transmission system (RTU) for operation of pipe irrigation network as per designed irrigation scheduling
up to Chak / Sub-Chak Level is to be assesed from detailed sample estimate for pattern adopted. Some of
the sample patterns are as under;
(a) SCADA control up to 200 Ha Chak Level and there after manual control
(b) With SCADA contorl up to 20 Ha sub-Chak Level and solonoid control valve up to hydrant at 1.25-1.5ha
(c) With SCADA contorl up to 20 Ha sub-Chak Level and solonoid control valve up to hydrant up to 1.75-
2.25ha
(d) With SCADA contorl up to 20 Ha sub-Chak Level and solonoid control valve up to hydrant up to 4.0-5.0ha
(e) With SCADA contorl up to 25 ha sub-Chak Level and solenoid control valve up to hydrant up to 8.0-8.5 ha

71 MICRO IRRIGATION
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER -XV
TUNNEL AND ALLIED WORKS
NOTES.
1 All General Notes are applicable to Tunnel and Allied Works to the extent they are relevant.
2 The basic rates are inclusive of additional costs for working inside tunnel, shaft and adit, with all
applicable machinaries whichever required for execution of underground works excluding the Tunnel
Boring Machine.
3 The basic rates are inclusive of scaling loose material, removal of under-cuts, cleaning bed including
lighting & ventilation inside tunnel.
4 Excavation - (A) All the open cut excavation upto Tunnel Portal / Adit Portal/ Inclined Shaft Portal
shall be measured and paid as per Chapter of Excavation.
Excavation - (B) The rates include dressing to the extent necessary for a particular item of work.
Excavation - (C) The payment for excavation shall be done as per pay-line indicated in the drawing.
The generally pay-line defined 15 cm beyond Minimum Excavation Line, In Bed no pay line
excavation shall be payable.
5 Unless otherwise specified the basic rates are inclusive of all leads and lifts.
6 Unless otherwise specified the basic rates are inclusive of standard finish (F2) required for concrete
surface.
7 For intake structure, tunnel portals, retaining walls, pitching etc, the rates as provided under Chapter
of Cement Concrete and other relavent chapter shall be adopted.
8 Measurements.- (A) Linear dimensions shall be measured to the nearest 0.01 m, the area shall be
worked out to the nearest 0.01 sq m and cubical contents to the nearest 0.01 cum.
Measurements.- (B) The measurement of permanent supports shall be done by weight, in kg. which
shall include the total weight of steel sections including the steel legging (if any), plates, bolts and
nuts and tie rods.
Measurements.- (C) No deduction shall be made for the volume of the reinforcement, but the volume
of permanent steel supports where provided shall be deducted from the total volume of concrete
9 lining.
The following Indian Standards may be referred to:-
Title Code No.
Safety Code for Tunneling work (first revision) 4756-1978
(Reaffirmed2007)
Code of practice for design of tunnels conveying water- 4880
General design(Reaffirmed1999) 4880 (Pt I )-1987
Geometric design (first revision) (Reaffirmed 2000) 4880 (Pt II)-1976
Hydraulic design (first revision) (Reaffirmed 2000) 4880 (Pt III)-1976
Structural design of concrete lining in rock(Reaffirmed 2000) 4880 (Pt IV)-1971
Structural design of concrete lining in soft strata and soils (Reaffirmed 2000). 4880 (Pt V)-1972
Tunnel supports(Reaffirmed 2000) 4880 (Pt VI)-1971
Structural design of steel lining(Reaffirmed 2000) 4880 (Pt VII)-1975
Code of practice for construction of tunnels- 5878
Precision survey and setting out(Reaffirmed 2000) 5878 (Pt I)-1971
Underground excavation in rock, section 1-Drilling and Blasting.(Reaffirmed 5878 (Pt II/Sec 1 )-
2000) 1970
Underground excavation in rock, section 2-Ventilation, lighting,Mucking and 5878 (Pt II/Sec 2)-
dewatering. (Reaffirmed 2000) 1971
Underground excavation in rock, section 3- Tunneling method for steeply 5878 (Pt II/Sec 3)-
inclined tunnels, shafts and underground power houses. (Reaffirmed 2000) 1971
Underground excavation in soft strata (Reaffirmed 2000) 5878 (Pt III)-1972
Tunnel supports (Reaffirmed 2000) 5878 (Pt IV)-1971
Concrete lining (first revision) (Reaffirmed 2000) 5878 (Pt V)-1976

72 TUNNEL AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

Steel lining (Reaffirmed 2000) 5878 (Pt VI)-1975

Grouting (Reaffirmed 2000) 5878 (Pt VII)-1972
Guniting equipment (Reaffirmed 2005) 6433-1972

S.N
Description of Item Unit Rate in Rs.
o
1 Excavation of tunnel up to pay line, Vertical/Inclined shaft, adit,
recess, enlargement by tunnelling methods including cost of
temporary supports in all types of soil/ rock strata (excluding cost
of providing permanent supports) including cost of blasting, all
materials, machinery, labour, ventilation, lighting, drainage,
dewatering, scaling excavated surface, removing and hauling
excavated muck outside tunnel up to specified dump area and all
other ancillary operations etc. complete with all underground lead and
lifts and ground lead up to 1km and all lifts. Including all applicable
taxes and levies etc
(a) Above 4.50 m D Shapped (Finished)/ Diameter (Finished) (Through Cum 3442.00
Shaft(s)/ Adit/Inclined Shaft)
(b) Above 4.50 m D Shapped (Finished)/ Diameter (Finished) (through Cum 2834.00
itself)
(c) Upto 4.50 m D Shapped (Finished)/ Diameter (Finished) (through Cum 4322.00
itself)
(d) Upto 4.50 m D Shapped/ Diameter (Through Shaft(s)/ Adit/Inclined Cum 4003.00
Shaft)
2 Geological Overbreak in underground excavation occurred due to Cum 1477.00
geological fault, removal of muck, stabilization of overbreak with
temporary supports etc including cost of all materials (excluding
back filling Concrete/masonry), machinery, labour, ventilation,
lighting, drainage, cleaning, scaffolding etc. complete with all leads
& lift. Including all applicable taxes and levies etc

3 Providing 25 mm thick guniting /shotcreting to sides and arch of Sqm 457.00

tunnel in M-25 proportion by weight including cost of all materials,
machinery, labour, ventilation, lighting, drainage and all other
ancillary operations etc. complete with all leads & lift. Including all
applicable taxes and levies etc
4 Providing and fixing Wiremesh of 100mmx100mm size 3.15mm wire Sqm 669.00
dia each ways or hard drawn steel wire fabric conforming to IS:1566-
1957 including all labour and materials with contractor's own
equipments Including all applicable taxes and levies etc; complete in
all respect
5 Providing and fixing 25 mm diameter HYSD Steel rock bolts with Per Mtr 584.00
adequate number of resin capsule including cost of all materials,
machinery, labour, ventilation, lighting, drainage, drilling 35-40 mm
dia. holes, threading one end of bolt for fixing nuts, inserting grout
capsule, driving bolt, fixing 10 mm thick and 200x200 mm size M.S.
plate washer and nuts, tightening the nuts by torque and all other
ancillary operations etc. complete with all lead and all lifts, including
testing bolt capacity for 10 % of fixed bolts. Including all applicable
taxes and levies etc
6 Providing fabrication and fixing in position permanent structural Per 98744.00
steel supports as per details including cost of all materials, Tonne
machinery, labour, ventilation, lighting, drainage, drainage cutting,
bending, welding, grinding and all other ancillary operations etc.
complete with all lead and all lifts. Including all applicable taxes and
levies etc

73 TUNNEL AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

7 Providing hoisting and fixing Precast Reinforcement Concrete in Cum 9234.00

shelves including setting in cement mortar (1:3) Cost of required
centering, shuttring and finishing smooth with 6 mm thick cement
plaster (1:3) on exposed surface complete but excluding the cost of
reinforcement with (1:2:4) (1Cement :2 Coarse Sand: 4Graded Stone
Aggregate 20 mm nominal size), all other ancillary operations etc.
complete with all ground and underground lead and all lifts.
Including all applicable taxes and levies etc

8 Providing and constructing un-coursed rubble stone masonry with Cum 3811.00
approved stones from tunnel excavated muck in CM 1:6 proportion
by volume for backfilling over cuts/ slips on tunnel sides due to
geological faults etc., including cost of all materials, machinery,
labour, ventilation, lighting, drainage, cleaning, scaffolding, batching
and mixing mortar, packing mortar and wedging stone chips in joints,
curing etc. complete with all leads and lifts. Including all applicable
taxes and levies etc
9 Providing and laying M-10 grade cement concrete using 40 mm Cum 5714.00
graded clean and hard crushed aggregate, for levelling and back
filling of geological over-cuts due to geological faults etc.,
including cost of all materials, machinery, labour, ventilation,
lighting, drainage, cleaning bed, batching and mixing concrete,
conveying up to placing point in agitator cars and Concrete pumps,
placing in position, vibrating, levelling compacting, finishing, curing
and all other ancillary operations etc. complete with all lead and lifts.
Including all applicable taxes and levies etc
(a) Add Extra if M-15 grade cement concrete used Cum 627.00
(b) Add Extra if 20 mm Aggregate used Cum 67.00
10 Providing and laying M-20 grade design mix Cum 8796.00
Reinforced cement concrete using 20 mm graded clean and hard
crushed aggregate, for kerb and bed lining including cost of all
materials (excluding cost of reinforcement), machinery, labour,
ventilation, lighting, drainage, form work, batching and mixing
concrete, conveying up to placing point in agitator cars and concrete
pumps, placing in position, levelling, vibrating, finishing, curing and
all other ancillary operations etc. complete with all lead and all lifts.
Including all applicable taxes and levies etc

(a) Add Extra if M-25 grade RCC used Cum 426.00

(b) Deduct if 40 mm Aggregate used Cum 67.00
11 Providing and laying M-20 grade design mix Reinforced cement Cum 11066.00
concrete using 20 mm graded clean and hard crushed aggregate, for
sides and arch lining including cost of all materials, machinery,
labour, ventilation, lighting, drainage, form work, rail mounted
shuttering gantry, batching and mixing concrete, conveying up to
placing point in agitator cars, placing in position using placer and
Concrete pump, levelling, vibrating, finishing, curing and all other
ancillary operations etc. complete with all lead and all lifts. Including
all applicable taxes and levies etc
(a) Add Extra if M-25 grade RCC used Cum 426.00
(b) Deduct if 40 mm Aggregate used Cum 67.00

74 TUNNEL AND ALLIED WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER -XVI
SURVEY, INVESTIGATION & TESTING
NOTES.
1 These rates are at work site inclusive of all leads, all taxes, GST, Contractor's profit, overheads , panchayat
tax & royalty etc.
2 Payment for SID works shall be released only after -(i) Submission of list of Bench Mark with value,
location and raw data / level book of field work.(ii) If survey is done by TS / DGPS then raw data with
northing and easting are to be submitted (iii) certification by field engineers that Bench marks and levels
has been checked and found correct.(iv) Submission of work in soft copy (Auto Cad file) and hard copy as
desired by Engineer in Charge.

S. No. Item Unit Rate in Rs

A SURVEY
1 Establishing the Bench Mark with latitude and longitude by DGPS keeping Each 8500
instrument stand still for a period (minimum 6 Hr) to give coordinate
accurate to 1m X 1 m and level accuracy 10 mm (plus or minusis achieved)
2 Construction of Pucca bench mark, muttam of size 30x30x75 cm in cement Each 1326.50
concrete (1:3:6) with maximum aggregate size of 40 mm with 75 cm long
MS angle , size 25x25x5 mm embedded including curing transportation and
fixing at site etc. complete with all leads & lifts.
3 Construction of pillar in M-15 concrete grade for demarcation of Forest Each 4209.00
land with size 60cm x 60cm x 60cm below foundation and 45cm x 45cm
x60 cm above ground with a crown of 23cm height.Nominal reinforcement
is to be provided. Engraving letters “F.D.”, Arrow, Numbers etc., painting,
lettering, marking complete in all respect as per direction of Engineer-in-
charge is to be done over pillar.
4 Construction of Pucca bench mark, muttam of size 30x30x75 cm in RR Each 2290.00
stone masonry in cement mortar(1:6) plastered on exposed surface with
cement mortar (1:6) in 20 mm thickness.
5 Supply of 3 cm x 3 cm x 30 cm size wooden pegs (Babul, mango or teak Each 14
wood etc.)
6 (a) Digitization of Jamabandi and providing excel sheet to the departmentNote: Per 100 240
Jamabandi Register will be provided by Department Khasra
(b) Digitization of Khasra map with details in layers and providing soft copy Per 100 625
(acad file)Note: Khasra map will be provided by Department Khasra
7 A Coloured Printing of Map on Bond Paper
(a) A0 - Paper size Each 400
(b) A1 - Paper size Each 225
(c) A2 - Paper size Each 150
(d) A3 - Paper size Each 60
(e) A4 - Paper size Each 30
B Black & White Printing of Map on Bond Paper
(a) A0 - size Map Each 125
(b) A1 - size Map Each 60
(c) A2 - size Map Each 45
(d) A3 - size Map Each 30
(e) A4 - size Map Each 5

75 SURVEY, INVESTIGATION AND TESTING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

C Scanning of Map and providing soft copy to the department

(a) A0 - size Map Each 300
(b) A1 - size Map Each 175
(c) A2 - size Map Each 100
(d) A3 - size Map Each 30
(e) A4 - size Map Each 12
8 Transfer of bench mark either by DGPS or using auto level (double
levelling) by recording levels at 30 meter interval and marking temporary
bench mark at suiatble location. For DGPS survey raw data file and for auto
level survey, level book along with value of bench mark, location and
plotting of the survey data is to be submitted to the department.
(a) In hilly area / km 2140.00
(b) In semi hilly area / km 1430.00
(c) In plain area / km 1170.00
9 Single levelling with auto level, recording level @ 30 meter interval,
chaining pegging for l-section and cross section survey work for new dam
and canal etc.Level book, bench mark value and location and plotting of the
survey data (L-section or X-section) is to be submitted to the department.
(a) In hilly area / km 1170.00
(b) In semi hilly area / km 990.00
(c) In plain area / km 800.00
10 Grid survey at interval of 30 x 30 meter to conduct submergence survey with
TS / DGPS instrument and prepare 0.50 m interval contour plan and
superimposing over khasra map including all ancillary works as described in
specifications and conditions of contract.Note: Khasra map will be provided
by Department
Marking of existing FRL, MWL, MDDL contours and dam alignment. / ha 375.00
Prepare area-elevation and storage -elevation curves and tables.
11 Hire charges of total station instrument with operator and staff for Per Day 5500.00
topography survey , command area survey, canal survey, dam survey etc.
and collection of data, plotting the details and preparing digital map of area
in layers, and developing contours where ever required as directed by
engineer in charge; including supply of detailed drawings in appropriate
scale in soft copy & three set of hard copy complete in all respect. These
rates are including all types of taxes applicable.

12 Hire charges of DGPS instrument with operator and staff for bench mark Per Day 11000.00
shifting, topography survey, command area survey, canal survey, dam
survey etc. and collection of data, plotting the details and preparing digital
map of area in layers, and developing contours where ever required as
directed by engineer in charge; including supply of detailed drawings in
appropriate scale in soft copy & three sets of Hard copy complete in all
respect. These rates are including all types of taxes applicable.

76 SURVEY, INVESTIGATION AND TESTING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

B FOR NEW WORK

13 Survey work in a grid at defined interval using Total Station / DGPS
instrument and preparation of Block level plan showing all permanent
features/ utilities including trees, for planning of dam/ canal / water course /
pipe network alignment and superimposing it on digitalized sajra map and
developing contours at interval desired by Engineer Incharge. Block level
plan is to be submitted in hard copy three set and soft copy in Auto Cad
format, using layer system, showing all features.Note:- Khasra map will be
provided by Department
(i) In hilly / semi hilly area - Block level to be taken @ 10 meter grid / Ha 550.00
(ii) In hilly / semi hilly area - Block level to be taken @ 15 meter grid / Ha 440.00
(iii) In Plain area - Block level to be taken @ 30 meter grid / Ha 350.00
14 Transfer of Dam / Canal alignment from sajra map to the ground and
taking Levels by Auto level or DGPS, developing L-section and X-section
and submitting in hard copy three sets and soft copy in Auto Cad format,
using layer system, showing all features. (Total length of L-section and X-
section to be measured for payment)
14.1 L-section of Dam/ Canal
(a) (i) In hilly / revineous area - Levels for L-section to be taken at interval 5 / Km 1640.00
meter.
(b) (i) In semi hilly area - Levels for L-section to be taken at interval 10 meter. / Km 1390.00
(c) (ii) In Plain area - Levels for L-section to be taken at interval 30 meter. / Km 1120.00
14.2 X-section of Dam/ Canal (Total length of X-section shall be measured)
(a) (i) In hilly / revineous area - Levels for X-section to be taken at interval 3 / Km 1870.00
meter.
(b) (i) In semi hilly area - Levels for X-section be taken at interval 5 meter. / Km 1580.00
(c) (ii) In Plain area - Levels for X-section be taken at interval 5meter. / Km 1280.00
C FOR RENOVATION / REMODELLING OF EXISTING DAM / CANAL / IRRIGATION
15 SYSTEM/
Survey workWHS with total station and preparation of L- section showing level
@ 30 meter and X-section with levels at suitable interval clearly showing
shape of canal, X-section should be extended both side 10m beyond bank
toe/borrow area. The location of C.D. works direct out lets (with size &
nos.) / cuts, regulators and existing lining (type and extent) be marked
(this shall be done separately for each main canal, branches/minors/sub
minors). Listing of present status of existing structures and lining reaches
indicating visible distress conditions complete in all respect with material
including nominal jungle clearance required for survey work. Digital
plotting of drawings with scale 1:2500 (H) and 1:100 (V) for L-sections and
1:100 (H&V) for cross sections for main canal / branches and 1:50 for
distributaries and minor/sub-minors including all ancillary works as
described in specifications and conditions of contract.

(a) (a) For Existing canal having discharge up to 10 cusec / Km 4800

(b) (b) For Existing canal having discharge >11 & up to 25 cusec / Km 5250
(c) (c) For Existing canal having discharge> 26&up to 100 cusec / Km 5800
(d) (d) For Existing canal having discharge> 101 & up to 200 cusec / Km 7000
(e) (e) For Existing canal having discharge >201 & up to 500 cusec / Km 9050
(f) (f) For Existing canal having discharge more than 501 cusec / Km 14500

77 SURVEY, INVESTIGATION AND TESTING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

16 (a) Survey of existing command area with TS / DGPS instrument at 30m grid /Ha. 360
and plotting of contours at 50 cm interval on Shajra map indicating existing
alignment of complete distribution system from main canal to water
course with marking of existing Chak boundaries and out lets / Nakka
points. Preparation of Khasra list of entire submergence / command area
receiving irrigation complete in all respect including all ancillary works as
described in specifications and conditions of contract.
(b) Survey of command area to be developed with TS / DGPS instrument at /Ha. 425
30m grid or at nearer interval as per requirement of site and plotting of
contours at 10 cm interval on Shajra map, planning of water cource for OFD
works and preparation of L-section of WC and drawings of Nakka point, CD
works etc.. Preparation of Chak planning booklet showing Khasra list with
details of beneficiaries for & CCA / ICA and Chak plan showing WC
alignment, Nakka Point etc. complete in all respect including all ancillary
works as described in specifications and conditions of contract.

(c) Add over item 20 (a) if revised Chak planning including re-alignment of /Ha. 100
water course , shifting location of existing outlets is required.
Preparations of revised Chak plan & water course alignment, out lets /
Nakka points marked on contoured sajra map and submitting l-section of
water course and, Khasra list, complete in all respect.

D EXPERT SERVICES
17 Water Sector Engineering Expert having experience more than 25 years for Per day 7000.00
providing expert opinion on Civil / Mechanical / Electrical & Electronics,
Engineering aspects regarding Dam, Gates, Canal Rehabilitation, Network
Planning, Water Management, Hydrology, suggesting remedial measures
and submission of inspection report and drawings where ever necessary.
18 Water Sector Engineering Expert (along with GIS operator) having Per day 8200.00
experience more than 25 years in engineering field, for providing expert
opinion on use of GIS software in canal Network Planning, Water
Management, Hydrology and submitting detailed task report and
presentation of report.
19 Hiring of subject specialist for providing consultancy services in the filed of Per day 10000.00
SCADA, HEM Experts, Heavy Machineries, Under Water Investigations,
Environmentalist etc having minimum experience of 15 years in respective
field. Conveyance shall be provided by the department from the WRD
division headquarter to field / site.

20 Geological investigation (where directed) Checking of retrogression below Per day 5300.00
spill arrangement, logging of bore log, rock strata classification, suitability
of structure foundation and suggesting remedial measures for control of
excessive seepage from foundation or body of the dam etc. by the
Geological expert having experience more than 15 years and submission of
final report.
21 Social Scientist (Empanelled by Competent Authority in Land Aquisition Per day 3500.00
Process) having field experience of 10 year to monitor/ conduct and analyse
the socio - economic - demographic data of the benefitted / affected villages
and to prepare report of social impact assesment study or social management
plan.

78 SURVEY, INVESTIGATION AND TESTING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

22 Computation of peak flood, routed flood and checking of the adequacy of Each 9500.00
flood discharge, capacity of existing spill arrangement. In case of existing Project
spill arrangements are found inadequate, the alternative proposals for
increasing spill capacity without changing the existing MWL or encroaching
the free board be suggested.
23 Based on the existing cropping pattern, water availability, suitable Each 16000.00
percentage of cropping pattern to be suggested after getting approval from Project
District Agriculture officer and crop water requirement data / water
allowances, finalize the duty and computing B.C. Ratio of the Project

24 Preparation of draw-off statement/design of canal section and all structures / Km 4200.00

and if modification needed anywhere be suggested and incorporating it in
preparation of draw-off statement, design, drawing etc for complete canal
system in all respect with material
25 Conducting a joint meeting and walk through survey with department, WUA Each 18500.00
and E&M consultant computing the list of works required to be executed for Project
improvement of overall irrigation efficiency and finalization of the list in
general body meeting of WUA and tentative rehabilitation (remedial and
improvement measures be suggested for preparation of Draft Detailed
Project Report).
26 Preparation and submission of the Draft Detailed Project Report for Each 40000.00
rehabilitation of minor irrigation projects, excellent printed and binded set Project
including all technical features design, drawings, cost estimates etc.
complete in all respect as per guide lines of department in one set of hard
copy and soft copy

27 Preparation and submission of final Detailed Project Report for Each 40000.00
rehabilitation of minor irrigation projects incorporating suggesation / Project
observation of approving authorities pointed out on draft report in three set
of hard copy with drawings and soft copy.
E FOREST LAND DIVERSION

28 Collection of forest map, revenue maps and GT sheet for every affected per village 3200.00
village from concerned department etc. required for online submission of
proposal for diversion of forest land.
29 Preparation of Georeferenced digital map of project area demarcating per Job 30000.00
forest/wild life affected area, superimposed over digitized cadastral map and
google image. KML file of project layout and forest/wildlife affected area is
also to be prepared and provided. Digitized cadastral map of project area/
alignment/ submergence area will be provided by departments. soft copy of
Geo-referenced map, KML file with 3 sets of hard copy is to be provided.

30 Preparation of case for diversion of forest-land/clearance of wild life per Job 170000.00
affected by project area, online submission of applications for diversions of
forest land/ clearance for wild life, pursuing the case in concerned offices
and office of any other authority whenever required representing the case
before the approval/clearance authority and finally getting first stage
clearance/approval for wildlife/Forest land clearance

79 SURVEY, INVESTIGATION AND TESTING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

31 Preparation and submissition of detailed Catchment Area Treatment (CAT) per sq km 100.00
Plan in accordance of forest (conservation), Act, 1980 for getting Forest
Clearance as per Norms of Forest Dept./ Water Resources Dept / Water
Shed Dept. For Major/Medium Irrigation Project. The Treatment plan shall
be made for free Catchment Area (excluding the area alread treated /
treatment plan prepared by Water Shed or any other Government agency)
and accordingly payment shall be made. All the geo
referenced Maps/ .shap/.kmz files of free catchment area prepared from GT
sheet/ Google/ DTM freely available and related documents shall also be
provided in soft/digital form to the dept. Correction/updation shall be made
by agency as and when desired by Forest Dept. / Engineer-in-Charge Note-
The 60 % payment shall be relesed after submission of CAT plan and rest
40% shall be released after approval / vetted by competant authority.

F INVESTIGATION WORK
32 Boring NX dia (54.7 mm dia), hole with diamond coring bits including
taking out of core and arranging etc. core in proper order in core boxes
including cost of core boxes. as per relevant I.S. code of practice. These
rates are including Mobilization & demobilization of Rig.
(a) In over burden including boulders Per metre 3400.00
(b) In stratified soft rock such as Phylite, lime stone of softer quality and Per metre 4000.00
compatible rock
(c) In sand stone and harder variety of lime stone Per metre 4550.00
(d) In soft granite and quartzite rocks Per metre 7300.00
(e) In hard granite and quartzite rocks Per metre 11700.00
(f) In dam masonry with softer quality of stone Per metre 3900.00
(g) In dam masonry with harder quality of stone Per metre 7350.00
33 Exploratory vertical drilling of bore holes 150 mm dia through all kind of Per stage 1350.00
soils with the adequate / suitable equipments, tools and tackles for depths
mesured below existing ground level including mobilization, setting up
boring rig, shifting of rig from 1 bore hole to another and demobilization of
the same
34 Boring NX dia, hole with non coring bits in over burden including boulders Per 2800.00
Sample
35 Procurement /collection of soil samples and filling in containers/boxes and Per 525.00
transporting from site to laboratory for testing with all leads & lift complete Sample
including all charges and indicating location of borrow area on Index Map.
36 Procurement /collection of construction material like sand aggregate stone, Per 525.00
brick, water etc and filling in containers/boxes transporting from Sample
site/source/quarry to laboratory for testing with all leads & and lift complete
including all charges and indicating location of source/quarry on Index-Map.

G TESTING
A SOIL
(I) PHYSICAL TEST
i Mechanical Analysis Each 2648.00
ii Liquid Limit and Plastic Limit Each 1144.00
iii Shrinkage Limit Each 680.00
iv Compaction (OMC, Dry Density using Standard procter density Test) Each 2136.00

80 SURVEY, INVESTIGATION AND TESTING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

v Specific Gravity Each 828.00

vi Permeability test in lab Each 668.00
vii Triaxial Shear Each 6100.00
viii Despersibility
(a) Pin Hole Test Each 1700.00
(b) Crumb Test Each 960.00
ix Differential Free swelling index Each 1524.00
x Determination of Carbonates Each 1128.00
xi Total Soluble Solids Each 1056.00
xii Sieve Analysis (Dry Test) Each 500.00
xiii Sieve Analysis (Wet Test) Each 1100.00
xiv Hydrometer analysis for Grain Size (Silt & Clay) Each 1400.00
xv Natural moisture Content Each 350.00
xvi Bulk Density Each 450.00
xvii Classification of Soil Group Each 2200.00
xviii Atterbergs’s (Liquid Limit, Plastic Limit and Shrinkage Limit) Each 1824.00
xix Swelling Pressure and Swelling Pressure Index Each 1400.00
xx Differential free Swell (free Swell index) Each 1524.00
xxi Linear Shrinkage Each 500.00
xxii Permeability Test in Lab Each 2200.00
xxiii Standard Proctor Density Test Each 2200.00
xxiv Modified Proctor Density Test Each 2200.00
xxv Consolidation test Each 3000.00
xxvi Triaxial Shear test without pore pressure measurement Each 2500.00
xxvii Triaxial Shear test with pore pressure measurement Each 3600.00
xxviii Direct Shear test (without OMC, MDD) Each 2400.00
xxix California Bearing Ratio Test in soaked / unsoaked condition Excluding Each 2400.00
OMC / MDD test
xxx California Bearing Ratio Test in soaked / unsoaked condition Including Each 4500.00
OMC / MDD test
(II) CHEMICAL TEST
i PH, Dissolve salts clorides, carbonates, sulphates Each 1128.00
ii Total Soluble Solids Each 1056.00
iii Dispersivity of soil Each 2660.00
iv Electrical conductivity / Electrical Resistivity Each 300.00
v Alkali Metals* (Na2O & K2O) Each 500.00
vi Sodium Absorption Ratio* (Na, Ca, Mg) Each 900.00
vii Total Kjeldahl Nitogen (TKN)* Each 700.00
viii Carbonate* Each 1128.00
ix Organic Matter Each 1300.00
x Cation exchange capacity* Each 500.00
xi Silica sesquioxide ratio*(SiO2+Al2O3+Fe2O3) Each 500.00
B COARSE AGGREGATE
i Specific Gravity & Water Absorption Each 1408.00
ii Gradation/ Particle Size Distribution and Finness Modulus Each 744.00
iii Impact Value Each 1540.00
iv Crushing Value Each 1276.00
v Soundness Each 3028.00
vi Abrassion Value Each 1052.00

81 SURVEY, INVESTIGATION AND TESTING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

vii Moisture content of Agreegate Each 300.00

viii Water Absorption Each 704.00
ix Specific Gravity Each 704.00
x Bulk Density Each 450.00
xi Flakiness & Elongation Index Each 650.00
xii Deleterious material Each 1500.00
xiii Stripping value (20mmm pass and 12.5mm retain) Each 850.00
xiv Petrography examination of aggregates (Macro) Each 3000.00
xv Alkali Aggregate Reactivity Each 2500.00
xvi 10% fine value Each 900.00
xvii WMM Mix Design (as per MoRTH)* / GSB / WMM Each 10000.00
xviii Iron Content* Each 650.00
xix Chloride and Sulphate Each 500.00
xx PH value* Each 400.00
xxi Organic impurities Each 1500.00
C FINE AGGREGATE / SAND
i Fine Modules Particle Size Distribution Each 744.00
ii Specific Gravity & Water Absorption Each 1408.00
a Specific Gravity Each 704.00
b Water Absorption Each 704.00
iii Silt Content Material finer than 75 micron Each 1460.00
iv Organic Matter Each 1300.00
v Bulk Density Each 720.00
vi Bulking* Each 400.00
vii Bulking at different moisture content Each 1000.00
viii Chloride, Sulphate Each 950.00
ix PH value* Each 400.00
x Deleterious Material Each 1500.00
xi Surface Moisture Content* Each 800.00
xii Soundness Each 3028.00
xiii Alkali Aggregate Reactivity Each 2000.00
D CEMENT
I PHYSICAL TESTING
i Fineness Each 808.00
ii Consistency & Setting Time Each 400.00
iii Initial & Final Setting Tiime Each 916.00
iv Specific Gravity Each 452.00
v Compressive Strength Each 1544.00
vi Soundness (Le-chatelier’s test) Each 872.00
vii Soundness (Autoclave Test) Each 1300.00
viii Density Each 450.00
ix Drying shrinkage (PPC) Each 1660.00
x Transverse Strength Each 800.00
xi Fineness by wet sieving* Each 500.00
II CHEMICAL TESTING
i Ratio of lime % to the % of Silica (SiO2) + Alumina (Al2O3) + Iron Oxide Each 600.00
(Fe2O3)*
ii Ratio of % of Alumina (Al2O3) to that of Iron Oxide (Fe2O3)* Each 600.00
iii Loss on Ignition Each 776.00

82 SURVEY, INVESTIGATION AND TESTING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

iv Silica (SiO2) Each 1520.00

v Ferric Oxide (Fe2O3) + Alumina (Al2O3) Each 3196.00
vi Alumina (Al2O3) Each 500.00
vii Ferric Oxide (Fe2O3) Each 4068.00
viii Calcium Oxide (CaO) Each 1480.00
ix Magnesia (MgO) Each 1540.00
x Total Sulphur content as Sulphuric Anhydride (SO3) Each 1944.00
xi Insoluble Residue (IR) Each 1048.00
xii Sodium Oxide (Na2O) Each 500.00
xiii Potassium Oxide (K2O) Each 500.00
xiv Free Lime (CaO) in Portland Cement Each 500.00
xv Chloride (Cl-) Each 500.00
xvi Alkali Content* Each 500.00
E STEEL
(I) Physical Tests:
i Tensile Strength Test (Ultimate Strength, 0.2% proof stress, Yield stress, Each 1100.00
Elongation, Nominal Mass)
ii Weight per meter* Each 250.00
iii Bend Test Each 650.00
iv Rebend Test Each 650.00
v Total Elongation at maximum force Each 1100.00
vi Coupler (Pull-out Test, breaking strength and fractural area)* Each 1100.00
vii Rib Area Each 350.00
(II) Chemical Tests
i Carbon Each 900.00
ii Sulphur Each 650.00
iii Phosphorus Each 650.00
iv Sulphur + Phosphorous* Each 850.00
v Silicon Each 650.00
vi Manganese Each 650.00
F Brick
i Water Absorption Each 1400.00
ii Compressive Strength Each 2280.00
G Stone
i Compressive Strength Each 1776.00
ii Water Absorption Each 2280.00
H OTHER CONSTRUCTION MATERIAL
i Compressive Strength Test Each 700.00
ii Efflorescence Test Each 500.00
iii Compressive strength of cement concrete tiles Each 700.00
iv Rock Hardness at Mho Scale Each 300.00
I Cement Concrete
i Compressive Strength Each 660.00
ii Mix Design Each 19352.00
J FIELD TEST
(excluding transportation facility for technician, Machines, T&P and
samples collected)
i Field Density by sand Replacement method (each test) Each 2500.00
ii Field Density by Core cutter method (each test) Each 1500.00

83 SURVEY, INVESTIGATION AND TESTING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

iii Compressive Strength of C.C. core Specimen supplied by the client (per Each 500.00
specimen)
iv Slump Test (each Test) Each 50.00
v Collection of soil samples from Borrow area (each sample) Each 350.00
vi Field CBR Each 7000.00
vii Standard Penetration test ( only for N value and safe bearing capacity) Each 7000.00
viii Conducting plate load test in accordance with IS 1888 at the depth of 2.0 to Each 30000.00
3.0 meter below natural ground level or specified by EiC including back
filling and ramming after test using same soil or equivalent.
ix Compressive Strength of C.C. cubes (per three cubes crushed only) Each 300.00
x Compressive Strength of C.C. cubes (if three cubes are to be prepared, cured Each 550.00
and crushed )
xi Compressive Strength of mortar cubes (per three cubes) Each 250.00
xii Compressive Strength of mortar cubes (if cubes are to be prepared for per Each 358.00
three cubes)
xiii Flexural strength Each 10000.00
xiv Rebound Hammer test at one location at Jaipur (Excluding Transportation) Rs. 800/-each location
+ 1000 mobilization charge
for each site

xv To determine the compressive strength/depth of cracks by Ultrasonic Pulse Rs. 10000/- at one
Velocity meter location (4 Nos. tests)
xvi To measure the degree of corrosion of Reinforcement by Corrosion Meter Rs. 8000/- at one location
(Half Cell Potential Meter) (4 Nos. tests)
xvii Pile Integrity Test Rs.1000/- per pile +
Mobilization charges

84 SURVEY, INVESTIGATION AND TESTING

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER -XVII

DISMANTLING & DEMOLISHING WORKS

NOTES:-
1 The rates given are for dismantling of good quality work. For dismantling poor quality or
weathered; weakened work the rates will be reduced by 30%.

2 Useable material from dismantalling of stone masonry will have to be properly

stacked/deposited.
3 The rates are inclusive of all taxes, levies, royalty, leads of all material and contractor's
profit etc.
4 The rates in this chapter are inclusive of de-watering wherever required.

S.No. Item Unit Rate in Rs

1 Demolishing lime concrete and disposal of material within 50 m

lead, inclusive of de-watering wherever required. Cum 432.60

2 Dismantling cement concrete including disposal of material within

50 m lead, inclusive of de-watering wherever required. Cum 762.30

3 Demolishing of reinforced concrete including stacking of usable

material and disposal of unuseable material within 50 m lead Cum 1030.10
inclusive of de-watering wherever required.
4 Demolishing brick work in cement mortar including stacking of
usable material & disposal of unuseable material within 50 m lead Cum 659.30
inclusive of de-watering wherever required.
5 Demolishing stone rubble masonry including stacking of usable
material and disposal of unuseable material within 50 meters lead
inclusive of de-watering wherever required.
(a) In lime mortar Cum 494.40
(b) In cement mortar Cum 576.80
6 Dismantling old plaster or skirting, racking out joints and cleaning
the surface for plaster including disposal of rubbish to the
Sqm 20.00
dumping ground within 50 m lead, inclusive of de-watering
wherever required.
7 Dismantling of masonry with care inclusive of de-watering
wherever required.
(a) Dry stone masonry or pitching Cum 115.00
(b) Stone masonry in mud Cum 90.00
8 Add extra for all type of dismantling work for height more than 5
m from ground level for every additional height of 3.0 m or part 20%
there-of.
9 Dismantling cement concrete lining including disposal of material
within 50 m lead, inclusive of de-watering wherever required of
thickness
(a) 10.0 cm Sqm 40.00
(b) 7.50 cm Sqm 28.00
(c) 5.0 cm Sqm 22.00

85 DISMANTLING AND DEMOLISHING WORKS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER - XVIII

MISCELLANEOUS WORKS
NOTE:-
(1) These rates are at work site inclusive of all leads and lifts and also inclusive of all taxes, levies, turn
over tax, income tax, service tax, sales tax, octroi, panchayat tax, Contractor's profit and royalty etc.
(2) The rates in this chapter are inclusive of de-watering wherever required except item 32.
(3) Stem of the trees shall be measured at 1 m above the ground level.
(4) Provision for item no 25 shall be taken with permission of Superintending Engineer
(5) “SPECIAL REPAIR OF DAM / CD WORKS”. Items from S.No. 47 to 59 are to be incorporated in
the estimate with the prior permission of zonal CE / ACE.

S.No. Item Unit Rate in Rs

1 Cutting & clearance of jungle, bushes, shrubs Ankra/Ipomoea,
Juliflora typna etc. on canal and bunds in dry/moist/slushy conditions
including disposal as per instructions of the Engineer-in-charge. Cost
of wood has been deducted from rates and thus will be property of
contractor after cutting.
(a) Ordinary Sqm 1.45
(b) Thick Sqm 2.50
(c) For dowels and outer slopes. Sqm 1.85
2 Cutting and uprooting of trees including removing of roots and filling
of hole, cutting/up rooted would be property of the department
(a) 7.5 cm to 15 cms girth Each 41.00
(b) Over 15 cms to 30 cms. girth Each 126.00
(c) Over 30 cms to 45 cms. girth Each 212.00
(d) Over 45 cms to 60 cms. girth Each 362.00
(e) Over 60 cms. girth Each 512.00
(f) (If uprooting and removal of roots is not required than 25% of the
above rates will only be payable and if only uprooting is required to be
done 75% of these rates will be paid)
3 Uprooting " Water Hyacinth" (Jal Kumbhi) or similar aquatic plants in
water including re-handling and disposal within lead of 250 m from
dam/canal.
(a) In dam submergence (when boat is to be used) Sqm 8.60
(b) In canal flow water Sqm 1.90
4 Weed clearance in canal and branches including disposal beyond canal
banks and its burning.
(a) In dry bed Sqm 1.15
(b) In pool of water Sqm 2.70
5 Cutting & uprooting of Sarkanda, or Arrows or Jhundas including Sqm 6.00
disposal as directed by Engineer-in-charge
6 Destroying and removal of unwanted perennial aquatic weeds, leaves
complete in all respect in irrigation tanks & canals by spraying un-
harmful chemical, of suggested concentration of herbicides on cluster
of roots/plants and leaves including cost of herbicides water spray
machine and skilled labour with usual precautions and measures etc.
complete (Complete killing will be considered when roots get affected
and degenerated).
i Dry condition Sqm 1.75
ii In pool of water Sqm 2.90

86 MISCELLANEOUS WORKS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

7 Thoor cutting (thick fencing of thoor) and disposal within initial lead R.M. 9.80
of 50 meters.
8 Dag belling
(a) 5 cm to 7.5 cm deep 10 M 8.00
(b) Over 7.5 cm to 10 cm deep 10 M 12.00
(c) Over 10 cm to 15 cm deep 10 M 16.10
9 Making new service road 4 to 5 m width including jungle clearance,
cutting of trees upto 10 cms dia, cutting of humps upto 30 cms, height
and filling local depressions, making of ramps on Nallah crossing etc.
(a) In plain area Km 7350.00
(b) In semi- hilly area Km 11650.00
(c) In hilly area Km 16650.00
10 Repair of existing service road including jungle clearance, filling cuts,
depression and dressing etc. complete.
(a) In plain area Km 2650.00
(b) In semi- hilly area Km 4000.00
(c) In hilly area Km 5660.00
11 Making standard type cement gauge including engraving letters and R.M. 550.00
painting including scaffolding etc.
12 Painting standard type gauge with black, red and white un-washable R.M. 210.00
paints including cost of material
13 Painting distance mark stone and lettering with light blue white or Each 120.00
yellow un-washable paint including cost of material
14 Supply of wire crates in required sizes made of hot dipped G.I. Wire Sqm 389.00
conforming to IS 4826 -1979 having mesh of 10 cm x 10 cm (surface
area of crate will be measured) made of wire of 5 mm diameter.

15 Filling crates with stone, in position at site including hinging with hot Cum 1090.00
dipped G.I. Wire 5 mm dia, excluding cost of wire crates, including
cost of stones in position complete in all respects.
16 Providing and fixing 200 mm dia Porous drain with precast cement Metre 2700.00
aggregate (1:4.5) blocks 0.60 m x 0.60 m x 0.30 m in two pieces
complete.
17 Providing and laying cement concrete coping in (1:2:4) with maximum
size of crusher broken aggregate upto 20 mm including shuttering etc.
with all leads of material complete in all respect in thickness of:
(a) 75 mm Sqm 480.00
(b) 50 mm Sqm 320.00
18 Labour charges for fixing of anchor bars in masonry Each 12.00
19 Supply and fixing in position of APM block made of C.I. as per Per block 10500
standard specification with adjustable arrangement and required
fixtures including transportation to site second stage concerning in
C.C. (1:2:4) centering shuttering painting with red oxide finishing etc.
complete in all respect cost of APM block (all size) per block

Note: APM block will be fixed in C.C. after adjusting throat with as
per requirement and as per direction of Engineer-in-charge.

87 MISCELLANEOUS WORKS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

20 Add extra over items of cement plaster/ cement concrete/cc.lining/cc per pack 60
flooring or RCC for providing and mixing Polypropylene/Polyester of 125 gm
fibres as per IS 16481:2022 or latest revision, 6/12 mm long @ 0.25%
(125 gram per 50 kg of cement) or in ratio of as specified by
manufacturer specification and direction of Engineer in charge with all
leads and lifts.
21 Labour charges for fixing stone patties/ lintels duly approved in
cement sand mortar (1:3) and pointing underneath with cement sand
mortar (1:3) for clear span up to 3.5 m of thickness.
(a) Upto 8 cm Sqm 170
(b) Above 8 cm Sqm 270
22 Providing & filling joints with sealing compound and coarse sand with Metre per 15
bitumen of grade 85/25 (6% by weight) cm depth.
23 Providing bitumen joints filter sheet conforming to IS: 1838-1983
(a) 12 mm Sqm 630
(b) 20 mm Sqm 780
(c) 25 mm Sqm 890
24 Supplying & fixing in position true to line and level elastomeric Cubic cm 1.5
neoprene bearings as per approved drawing and specifications
conforming to IRC-83 (Part -II) 1987.
25 Supplying & fixing in position MS precision machined finger type Kg 75
expansion joints as per approved detailed drawing and specification
conforming to standard drawing of MOST BD/I-69 A.
26 Supplying of well stitched earth filled bags of capacity, weigh not less
than 40 kg per bag at site etc. complete.
(a) Jute bag Each 32
(b) Plastic bag Each 16
27 Labour charges for making coffer dam/ring bund (under flowing / bag 26
stagnate water pool) by loading transporting earth filled cement bags
dropping at required locations in water including lead up to 3 km and
lift up to 8 meter from NSL complete (excluding cost of earth filled
cement bags).
28 Providing, laying and fixing in position RCC spun or hume pipe with
collars (ISI 458-2003) in required size packed in gasket for hume or
spun yarn & neatly finished with rich grout of cement mortar 1:3
perfectly air tight including testing of joints.

Description Unit Rate in Rs

Labour Charges only
(diametre) ( Excluding Labour Charges )
NP-2 NP-3 NP-4
(a) 150mm RM 434.00 465.00 520.00 66.00
(b) 200mm RM 527.00 558.00 595.00 106.00
(c) 250mm RM 620.00 657.00 731.00 110.00
(d) 300mm RM 929.00 1059.00 1233.00 132.00
(e) 450mm RM 1165.00 2094.00 2385.00 215.00
(f) 600mm RM 1635.00 3098.00 3544.00 231.00
(g) 900mm RM 3525.00 5941.00 7552.00 403.00
(h) 1000mm RM 4045.00 7217.00 8667.00 442.00
(i) 1200mm RM 5532.00 8605.00 12334.00 553.00
Note: Non ISI mark pipe but manufactured as per ISI deduct 20%

88 MISCELLANEOUS WORKS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

29 (a) Numbering of trees including identification for compensation, making Each 42.00
surface for numbering in size 15x15 cm and marking / writing /
appropriate indicated number by black enamel paint of approved
quality including cost of paint, brush, T&P etc.
(b) Numbering of trees and painting after peeling the bark making surface Each 32.00
for numbering in size 8 x 10 cm marking / writing / appropriate
indicated number by black enamel paint of approved quality including
cost of paint, brush, T&P etc.
30 (a) Operation & controlling including watch & ward of Head / Cross Each 1245.00
regulator gates for Feeder/main canal / distributory.
Appointing three opertor cum gauge reader per day, one in each shift
of 8 hr.
i) Where ever there is head cum cross regulator, no separate staff
would be taken.
ii) If two head/ cross regulator are within 1 km reach, no separate staff
would be taken.
(b) Operation & controlling including watch & ward of Head / Cross Each 610.00
regulator gates for Feeder/main canal / distributory.
Appointing one opertor cum gauge reader per day for (24 hr.)
i) Where ever there is head cum cross regulator, no separate staff
would be taken.
ii) If two head/ cross regulator are within 1 km reach, no separate staff
would be taken.

31 Regulation & patrolling of Feeder/ Main / Branch/ Distributory and

Minor canals of canal irrigation projects with their own conveyance
system (Two Wheeler with POL) and mobile (with recharge pack) for
communicating with site incharge or control room. including Jute
rassi, Torch, Fawda etc. all T&P required for regulation.

(a) Canal Having Discharge capacity up to 100 cusec Per 2 km / 420

day
(b) Canal Having Discharge capacity 100 cusec to 500 cusec Per 2 km / 505
day
(c) Canal Having Discharge capacity 500 cusec to 1000 cusec Per 2 km / 677
day
32 Canal Having Discharge capacity > 1000 cusec Per 2 km / 1105
day
33 Watch & ward of office building after office hours. per day 787.00
34 Watch & ward of irrigation colonies campus, houses with or without
office buildings.
(a) for Colony having 50 no buildings, one chowikidar is to be provided per day 393.00
(b) Colony having 51 no to 200 no buildings, two chowkidar is to be per day 878.00
provided
35 (a) Watch & Ward of spillway gates for Major, Medium & Minor per day 1180.00
Irrigation Projects
(b) Watch & Ward including operation of spillway gates for Major, per day 1789.00
Medium & Minor Irrigation Projects as per direction of Engineer in
Charge, providing one beldar in every shift and one electrician as per
requirement
36 Cleaning of irrigation colonies campus road and road side drains with
or without office buildings
(a) for Colony having 50 no buildings, one chowikidar is to be provided Per Month 9735.00
(b) Colony having 51 no to 200 no buildings, two chowkidar is to be Per Month 19470.00
provided

89 MISCELLANEOUS WORKS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

37 Watch & ward of irrigation rest houses I class building Per day 2099.00
( supplying 2 beldar and two chowkidar daily, one gardner)
38 Patrolling and watch & ward of dam with Mobile phones (with
recharge pack) for communicating with site incharge or control room P.Km/day 990.00
including T&P.
39 Maintenance and upkeep of plants, trees, lawn and other flower pots Per day 691.00
including watering etc. complete but excluding compost, pesticide.
40 Fixing of Distance stone in 30x30x30 cm pit excavated in all type of Each 250.00
strata and back filling with cement concrete (1:4:8) projected 10 cm
above ground level well finished and properly cured. (Excluding cost
of Distance stone)
Measuring devices
41 Supply and fixing at site (except civil work required) for accurate
measurement of flowing water through channels of calibrated pre-
fabricated fibre-glass reinforced plastic (FRP) moulded cut throat
flume without any joint, with a side chamber provided in U/S
connecting through pipe at bottom with water flowing flume accurate
in dimensions and having accuracy of + 1 mm smooth & uniform
surface with 0.013 as value of rougosity, inside blue outside gray
colour, with engraved gauge marking in cm and litre per second &
engraved discharge table showing calculation discharge variation at
every 0.10 cm and flow measured at submerged condition etc.
complete in all respect. The flumes shall consist from M.S. pipe frame
embaded in moulding, light in weight and easy in handling including
stiffeners hold fast, sand treatment on the back side of flume etc.
complete.
(a) Channel discharge in Cusec
(b) Up to 1 cusec, 3 mm thick Each 4570
(c) Up to 2 cusec, 3 mm thick Each 11700
(d) Up to 3 cusec, 3 mm thick Each 15000
(e) Up to 4 cusec, 3 mm thick Each 15600
(f) Up to 5 cusec, 4 mm thick Each 38600
(g) Up to 6 cusec, 4 mm thick Each 39400
(h) Up to 8 cusec, 4 mm thick Each 43500
(i) Up to 10 cusec, 4 mm thick Each 44700
(j) Up to 12 cusec, 5 mm thick Each 51590
(k) Up to 15 cusec, 5 mm thick Each 53800
(l) Up to 20 cusec, 5 mm thick Each 61900
(m) Up to 25 cusec, 5 mm +-1mm thick Each 94400
(n) Up to 30 cusec, 5 mm +-1mm thick Each 98000
(o) Up to 40 cusec, 5 mm +-1mm thick Each 114000
(p) Up to 50 cusec, 5 mm +-1mm thick Each 122900
(q) Up to 60 cusec, 6 mm +-1mm thick Each 133600
(r) Up to 70 cusec, 6 mm +-1mm thick Each 145300
(s) Up to 80 cusec, 6 mm +-1mm thick Each 157900

90 MISCELLANEOUS WORKS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

42 Supply and fixing at site (except civil work required) for accurate
measurement of flowing water through channels of calibrated pre-
fabricated fibre-glass reinforced plastic (FRP) moulded Parshall
Flume, with a side chamber provided in U/S connecting through pipe
at bottom with water flowing flume accurate in dimensions and having
accuracy of + 1 mm smooth & uniform surface with 0.013 as value of
rougosity, inside blue outside gray colour, with engraved gauge
marking in cm and litre per second & engraved discharge table
showing calculation discharge variation at every 0.20 cm and flow
measured at submerged condition etc. complete in all respect. The
flumes shall consist from M.S. pipe frame embaded in moulding,
assemble dissemble system for easy in handling / transportation
including stiffeners hold fast, sand treatment on the back side of flume
etc. complete.

Channel discharge in Cusec

(a) Up to 100 cusec, 7 mm +-1mm thick Each 365000
(b) Up to 150 cusec, 7 mm +-1mm thick Each 388800
(c) Up to 200 cusec, 7 mm +-1mm thick Each 698000
(d) Up to 250 cusec, 7 mm +-1mm thick Each 715000
(e) Up to 300 cusec, 7 mm +-1mm thick Each 735000
(f) Up to 400 cusec, 7 mm +-1mm thick Each 776000
(g) Up to 500 cusec, 8 mm +-1mm thick Each 1280000
(h) Up to 750 cusec, 8 mm +-1mm thick Each 1370000
(i) Up to 1000 cusec, 9 mm +-1mm thick Each 1450000
(j) Up to 1250 cusec, 9 mm +-1mm thick Each 1506000
(k) Up to 1500 cusec, 9 mm +-1mm thick Each 1575400
43 Supply and fixing at site (except civil work required) for accurate
measurement of flowing water through channels of calibrated pre-
fabricated fibre-glass reinforced plastic (FRP) moulded V Notch
as per IS: 9108:1979 with a side chamber provided in U/S connecting
through pipe at bottom with water flowing flume accurate in
dimensions and having accuracy of + 1 mm, with engraved gauge
marking in cm and litre per second & engraved discharge table
showing calculation discharge variation at every 0.10 cm and flow
measured at submerged condition etc. complete in all respect.

Drain discharge in Lit / sec

(a) 15 Lit / sec 9800
(b) 30 Lit / sec 15400
(c) 45 Lit / sec 17330
(d) 60 Lit / sec 20800
(e) 90 Lit / sec 26450
(f) 120 Lit / sec 33550
44 Supply of fibreglass reinforced plastic (FRP) Gauge plate for accurate
measurement of water level, moulded and sandwiched with MS strip
both side finish, front side engraved and molded computerized
marking of bands and figures covered in radium, eye pleasent colour
combination, laminated with high abrasioj grade polyurethane ,
provision of MS pressed channel for gauge plate more than 60 cm
width etc., complete as directed.

(a) 10 cm wide P RMT 4450

(b) 15 cm wide P RMT 5450
(c) 30 cm wide P RMT 8450
45 Annual charges for boating in Irrigation reservoirs

91 MISCELLANEOUS WORKS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

A For Tourist recreation on commercial basis.

(a) Up to 2 seater boats all types Per Year 9250
(b) Up to 4 seater boats all types per boat 18600
(c) Up to 20 seater boats
i. Driven by Natural gas, Battery, Solar Energy & Manually Per Year 31100
ii. Driven by all other types per boat 62100
(d) More than 20 seater boats
i. Driven by Natural gas, Battery, Solar Energy & Manually Per Year 49650
ii. Driven by all other types per boat 124000
(e) Application Charges for Item 44 A (Non Refundable)
i. For Cooperative society/Govt & Semi Govt. Department 640
ii. For Private Persons 1290
iii. For Registered Private Firms 1830
B For recreation, transportation of Occupants of hotel by
registered firms/hotels
i Up to 2 seater boats all types Per Year 12400
ii Up to 4 seater boats all types per boat 31100
iii Up to 20 seater boats
(a) Driven by Natural gas, Battery, Solar Energy & Manually Per Year 62100
(b) Driven by all other types per boat 124200
iv More than 20 seater boats
(a) Driven by Natural gas, Battery, Solar Energy & Manually Per Year 62100
(b) Driven by all other types per boat 186000
v Application Charges for Item 44 B (Non Refundable)
(a) For Registered Private Firms/Hotels Per Year 3780
C For fishing purpose
Application Charges for Item 44 C (Non Refundable)
i. For Cooperative society/Govt & Semi Govt. Department Per Boat 160
one time
Per Boat 320
ii. For Private Persons
one time
Per Boat
iii. For Registered Private Firms
one time 540
D For transportation of Goods & other purpose other than A, B & C
above
i. Government /semi government department Per ton 6200
ii. For Registered Private Firms/Hotels Per ton 12400
Application Charges for Item 44 D (Non Refundable)
i. For Govt & Semi Govt. Department 645
ii. For Registered Private Firms/Hotels 1295
46 (a) Photography or Video shooting on irrigation structures / Reservoirs / Per Day 3780
Encroachment on department land / Illegal irrigation practice at site
etc. for documentary or reporting to higher officers including soft
copy of photography/ videography. (without conveyance)
(b) Photo Print 6" x 4" Each 27
47 Photography / Videography by Drone mounted with camera of high
resolution with different angles showing perspective view covering
specified features as detailed under:
(a) For Videography / photography of Canal and its appurtenance Length Per / day 6000
of 2.25 km is to be covered in a day including all taxes but exluding
conveyance charges. Soft copy of photographs / videography and one
set of 25 no Hard copy in 9" X 5" for all ptotographs captured is to be
provided.

92 MISCELLANEOUS WORKS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

(b) For Videography / photography of Dam and its appurtenance including Per / day 6000
submergance, minimum three sites are to be covered in a day
including all taxes but exluding conveyance charges. Soft copy of
photographs / videography and one set of 25 no of Hard copy in 9" X
5" for all ptotographs captured is to be provided.

SPECIAL REPAIR OF DAM / CD WORKS

These items are to be included in estimate with the written
permission of concerned Zonal Chief Engineer / ACE
48 Providing UV resistant , monotoxic, high strength, non shrink,polymer Per Sqm 4120
based Cementitious repair mortar such as Poly Ironite Ceremic
Cementitious (PICC) for resurfacing on damaged surfaces of concrete
dams, masonry dams and colgrout faced dams and hydraulic structures
to a thickness upto 10 to 15 mm or as per surface conditions and also
treatment to the lift joints and honeycombed areas, potholesetc. by
removing loose material particles, grout slurry, by breaking using
manual and /or mechanical means, removing of existing embedded
M.S.bar if any, cleaning the lift joints, honeycombing areas and
surface with special chemical for algae fungi removal and protection
with pressure water jet / sand blasting, applying a bond coat of special
type of primer suitable to bond old to new concrete and concrete to
rock for required bond strength before application of repair mortars
and providing a water repellent coat after finishing complete as per
specification including materials, machinery, labour, scaffolding with
special hanging platform, hire charges of cranes, insurance charges
transportation as directed by Engineer in charge.

49 Under water videography of dam body & its appertunance i.e gates, Per Hour 9199
under sluice, emergency gate grooves clearly showing location defect
area or area of interest indicating condition from all possible angles
and special focus on damaged portions complete in all respects upto
the satisfaction of Engineer in charge. The work also includes supply
of three sets of video in digital form and a depth wise report prepared
in hard copy.
50 Cleaning drainage gallery, adits, instrumentation galleries etc. by Per Sqm 65.00
scrubbing/ brushing including chiseling and removing leached lime
deposit and disposing off all the waste material outside adits in
specified location as directed etc., complete with all leads and lifts.

51 Supplying, Laying and fixing in position of 5 MM thick Geosynthetic Per Sqm 3850.00
Cementatious composite mat, specified as per ASTM: D 8364.
2
Initial flexural strength (1 Day) should be > 3.5 Mpa or 3.5 N/mm
and 28 days compressive strength as per ASTM D8329 should not be
2
less 40 Mpa or 40.0 N/mm .

93 MISCELLANEOUS WORKS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

52 Supply laying and Pushing of MS casing pipe of specified thickness

approved by concerned departmental authority by trenchless method
adopting micro-tunnelling or any suitable mechanical technology or
technology approved by Railway below ground at all depth for
crossing CD works / embankments in all respect, including excavation
of driven pit and exit pit ( depth up to 3 meter) with proper protection.
Providing MS cutting edges for front shield and Constructing thrust
bed at designated level. Necessary de-watering and providing concrete
foundation at the base of the driven pit, PVC/Rubber saddle as per the
requirement, crane for handing of pipe and any other machinery, tools,
and tackles required, construction of temporary works as per design,
drawing, requirement, approved by authority, specification and the
direction of the Engineer.
Apply corrosion resistant, protection on inside and outside of casing
pipe as per technical specification.

Note:- This item is to be used for Railway / NH / Express way

crossings only
In all type of soils
i 300 mm dia 8 mm thick casing pipe R. Mt 19,250.00
ii 400 mm dia 8 mm thick casing pipe R. Mt 22,950.00
iii 500 mm dia 8 mm thick casing pipe R. Mt 23,880.00
iv 600 mm dia 10 mm thick casing pipe R. Mt 31,050.00
v 700 mm dia 10 mm thick casing pipe R. Mt 34,550.00
53 Providing, jointing, laying, testing and commissioning of HDPE PE-
100/PN-6 (suitable for pulling method for jointing) pipes for
micro irrigation pipe network / crossing embankment as per IS-
14333 (amended upto date) with compliance for maintaining slope
as per design by trenchless adopting HDD method (Horizontal
Directional Drilling) below ground at all depth including carriage
etc. complete in all respect, construction of thrust pit and
receiving pit of required size upto 3 metre depth and soil
investigation, making suitable arrangement for barricading of pits,
traffic diversion, and necessary permission from relevant authority
(though department will assist in getting the permission), refilling of
pits in compacted layers of 150 mm including disposal of
surplus material with all lift and lead upto 50 metre as per
specification and the direction of the Engineer.
Note:- This item is to be used for crossings canal , embankments, CD
works etc.
In all types of soil including mixed starta
i 200 mm outer dia R. Mt 4,920.00
ii 225 mm outer dia R. Mt 6,760.00
iii 250 mm outer dia R. Mt 7,480.00
iv 315 mm outer dia R. Mt 9,130.00
v 400 mm outer dia R. Mt 15,500.00
vi 450 mm outer dia R. Mt 17,300.00

94 MISCELLANEOUS WORKS
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER -XVIII (A)

MISCELLANEOUS WORKS

Complete
S.N. Description Unit
Rate
Under Water Treatment : -
1 Providing and Fixing packers including grinding 14/18 mm diameter holes, fixing self
griping injection packers, sealing leak paths temporarily using fast setting mortar or Nos. 851.00
epoxy, removing packers after injection.
2 Providing treatment to the observed leakages through the spill way piers/ogee/ inspection
galleries by injecting hydrophophobic,A rigid-flexible sealing and strenghthening, low
viscosity, high compressive (>60MPa) and flexural strength (>45 MPa) polyurethane-
based elestic resin, non toxic with no negative envoiromental effect, to the cracks joint
and cavities in high pressure water bearing condition, injected in to the substrate using
pneumatically operated two component pump including drilling holes of 14 mm dia 300
mm deep, flushing drill holes with clean water, sealing leak/crack paths with rapid KG. 5676.00
setting cement, fixing non corrosive aliminium injection packers of size 13 mm dia 100
mm long licluding cost of all material, HOM of machinery, consumables like PU
cleaners, catalysts, static mixers, lubricating oil, flexible high pressure hose adapters etc,
cost of labour, scaffholding, finising etc complete with all lead and lifts and as per
directions of Engineer-in-Charge.

3 Cleaning by redrilling the vertical porous drain pipes for complete depth of holes
(Vertical from 0 m to 20 m) including removing of leaching grout material if any inside
of the V.P.D. including depth up to 5.0 m with all leads and lifts etc. complete as per R.M. 7504.00
direction of Engineer-in-charge. ( Vertical upward/ downward drilling).
4 Providing & apply of internal cement based water proof protective coating including
complete charges.Cutting of wall lift area with drilling, remove cutting subsequent with
grouting work with all lead , lift & cost of all metarials etc. complete as per approved Sqm 1198.00
design, drawing & specification and as directed by engineer-in-charge
5 Providing & applying abrasion resistant fibre reinforced shrinkage compenseted R-4
(Based on 1504-3) category thixotropic repair mortar with anti-acid impermeable by
manual method specified by manufacturer datasheet, consultant & engineer in charge Sqm 7158.00
include of curing for the build up to thickness average up to 20 mm as per relevant
specification etc. complete

6 Treatment of Underwater RCC Cold Joints / Cracks

6.1 Surface Preparation of the entire surface area by hand and power tool for removing alge,
mud, debris and other forign material for exposing cracks and other defects and marking
the damaged area of the substrate and making videos and photo survey for assesing the Sqm 504.00
quantum of the damages.
6.2 Groove Cutting :
Making 'V' groove of 5mm to 10 mm wide and 5mm to 10 mm deep over crack / joint R.M. 1057.00
line as per site requirement by including labour, tools & tackles etc

6.3 Groove Filling :

Application of two component, solvent free, moisture insensitive epoxy resin based patch
/ groove repair putty like Sikagard 694 F(I).or Equalant The product should suitable
for under-water applications, having mixed density of 1.55 Kg / litre, compressive KG. 1520.00
strength of > 20 N/mm2 (1 day) according to IS 9162-1979, Bond Strength of > 2.5
N/mm2 (3 Day ) as per EN 1542 and Slant Shear Strength of > 10 N/mm2 ( 3 Days ) as
per ASTM C 882 on Dry Concrete.

95 MISCELLANEOUS WORKS A
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

Complete
S.N. Description Unit
Rate
6.4 Grouting Packers Placement & Removal :
Drilling and fixing injection packers in RCC members including, Drilling holes in
structural members at the intervals as per site conditions, clean the holes by air blower
prior to fixing nozzles , insert 12 mm dia., minimum 50~75 mm long injection packers in
cleaned holes with moisture insensitive epoxy resin based putty Sikagard 694 FI, Nos. 784.00
grouting the packers approved material using suitable grouting pump as per site
requirement & cutting the packers by mechanical means after completion of grouting
work without damaging structural elements including cost of material, labour, tools &
tackles etc but excluding cost of grouting material as per approval.

6.5 Grouting Material :

Application of two part, low viscosity, moisture insensitive epoxy resin based injection
grout like Sikadur®-53 UF or equivalent technical specification The product should be
suitable to seal damp, wet and submerged cracks; having mixed density of ˜ 1.1 kg / litre,
compressive strength of >40 N/mm2 at 1 Day & > 75 N/mm2 at 14 Days, 30 Deg C as KG. 2072.00
per ASTM C 579, Tensile Strength of >40 N/mm2 at 14 Days as per ISO 527, Bond
Strength of > 10 N/mm2 (failure in concrete) according to ASTM C 882. Inclusive of
material cost , transportation, labour, tools & tackles etc

7 Treatment of Underwater patch repairs / honeycomb area

7.1 Application of two component, solvent free, moisture insensitive epoxy resin based patch
/ groove repair putty like Sikagard 694 F(I); including surface cleaning & removal of
any loosely bonded concrete by mechanical means. The product should suitable for under-
water applications, having mixed density of 1.55 Kg / litre, compressive strength of > 20
KG. 1792.00
N/mm2 (1 day) according to IS 9162-1979, Bond Strength of > 2.5 N/mm2 (3 Day ) as
per EN 1542 and Slant Shear Strength of > 10 N/mm2 ( 3 Days ) as per ASTM C 882 on
Dry Concrete.

8 Treatment of Underwater Honeycombed area, by providing shuttering.

8.1 Providing & installating shuttering on honeycomb area. Using conventional shutter as
formwork-. Providing, fixing and removing. Including loading, unloading, shifting and
transportation of formwork from one location to next location, all joint shall be sealed to
prevent leakage proof by using foam or rubber sheet, applying shutter oil on inner KG. 1680.00
surface before fixing of shuttering, formwork (including all consumable material)

8.2 Providing and under water application of Moisture Insenstive, High strengh, 3
component fillerised epoxy grout like Sikadur-53 UF Grout or Equalant , including
providing necessary shuttering, tools etc. The Product should cure underwater, by
displacing water and should have Compressive Strength of > 45 N/mm2 at 1 Day and > KG. 1008.00
60 N/mm2 @ 7 Days as per IS 9162-1979 & FIP 5.12; Bond Strenght of > 10 N/mm2 as
per ASTM C 882

8.3 Under water pre and post survey

under water pre and post survey for accesing quantum of damage and repair work with
all lead lift complete with all respect Sqm 1888.00

96 MISCELLANEOUS WORKS A
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER -XVIII (B)

MISCELLANEOUS WORKS

Item Complete Labour

Description Per / unit
No Rate Rate
1 Providing of Steel wire ropes as per IS:2266/2002 for dams, sluices, canals, barrage, stop log gates etc of
Construction 6X37(18/12/6-1), FMC, GAL-B Finish, RHO Lay, A1 Lub, T/S=1960N/mm2 of required
size, type and specifications with testing, including all lead and lift, packing and forwording charges for
all components etc, complete in all respects.
1.1 20mm Diameter, MBL= 231KN P. Meter 394.00
1.2 22mm Diameter, MBL= 280KN P. Meter 464.00
1.3 24mm Diameter, MBL= 333KN P. Meter 556.00
1.4 26mm Diameter, MBL= 391KN P. Meter 650.00
1.5 28mm Diameter, MBL= 453KN P. Meter 747.00
1.6 32mm Diameter, MBL= 592KN P. Meter 965.00
1.7 36mm Diameter, MBL= 749KN P. Meter 1177.00
1.8 38mm Diameter, MBL= 834KN P. Meter 929.00
1.9 40mm Diameter, MBL= 924KN P. Meter 1023.00
2.1 Labour charges for removal of existing old/ damaged Steel wire ropes of Crest gate, Gantry crane, etc of
dams, canals, barrage, etc & replacing it with new wire ropes with proper care & applying cardium
compound on the wire ropes including all sort of labour, tools, tackles & taxes, all lead & lift, cost of Metre 536.00
cardium compound, thimbes etc, complete in all respects and upto the satisfaction of engineer in charge.
Gate lifting wire rope
2.2 Labour charges for removal of existing old/ damaged Steel wire ropes of Crest gate, Gantry crane, etc of
dams, canals, barrage, etc & replacing it with new wire ropes with proper care & applying cardium
compound on the wire ropes including all sort of labour, tools, tackles & taxes, all lead & lift, cost of Metre 892.00
cardium compound, thimbes etc, complete in all respects and upto the satisfaction of engineer in charge.
Counter weight wire rope
3 Providing of Rubber Seals as per IS:11855/1986 for crest gates/stop log gates of dams, barrage, canals of
required size, type and specifications with testing including all lead and lifts, packing & forwarding
charges for all components, etc. complete in all respects. (Including 18% GST)
3.1 Musical Knote, Hollow Bulb type, Side Rubber Seal (Taflone Cladded) Size: 100 x 40 x 15 MM P. Meter 2,393.00
3.2 Musical Knote, Solid Bulb type, Side Rubber Seal (Taflone Cladded) Size: 100 x 45 x 15 MM P. Meter 2,720.00
3.3 Flat type, Bottom Rubber Seal, Size: 90 × 20 MM P. Meter 1,780.00
3.4 Flat type, Bottom Rubber Seal, Size: 100 × 20 MM P. Meter 1,845.00
3.5 Solid Bulb, Double stem type, Top Rubber Seal (Taflone Cladded) Size 160 × 45 x 15 MM P. Meter 2,545.00
3.6 Rubber Seal Corners (3D) for hollow bulb musical note type Side seal(100x40x15MM) with Flat type
P. Set 6,608.00
Bottom Seal size (90×20 MM), Taflone Cladded, 300MM x 300MM long (Set of 2PCS LHS & RHS)
3.7 Rubber Seal Corners (3D) for Solid Bulb Musical note Side seal(100x45x15MM) with Flat type Bottom
P. Set 7,316.00
Seal (100×20MM), Taflone Cladded, 300MM x 300MM long (Set of 2PCS LHS & RHS)
3.8 Rubber Seal Corners (2D) for Solid Musical note Side seal(100x45x15MM) with Solid Bulb, Double
P. Set 5,098.00
stem type, Top Seal (160×45x15 MM), Taflone Cladded, 300x300MM long (Set of 2PCS LHS & RHS)
3.9 Rubber Seal Flat Type Size : 120 MM x 20 MM ,Teflon Cladded P. Meter 3,068.00
3.10 Rubber Seal Z Type Size : 120 MM x 75 MM x 35 MM x 20 MM(L-75 MM/35 MM) ,Teflon Cladded P. Meter 3,540.00
Musical Knote, Solid Bulb type, Side Rubber Seal (Taflone Cladded) Size: 100MM x 35 MM x 12 MM P. Meter 2,065.00
4 Supply & fixing of Bearing No N222 ECP SKF or equivalent for Balancing pulley for wire rope of
Each 30,513.00 873.00
Radial/ Verical gates of Dams / Barrages
5 Labour charges for repairing for making wire rope free from load, from balancing pulley, taking out of
Each - 28,318.00
damaged pulley, checking, Repairing and Re-fixing, including trail, testing etc. complete in all respect.
6 Labour Charges of Checking of wire rope ends 28mm & 38mm dia including applying cardium
Each Rope - 734.00
compound to be supplied by department.
7 Labour charges for reversing ends of wire rope and applying cardium compound supplied by department
Each Rope - 4,172.00
on 38mm dia ( 4 ropes per gates )
8 Operation of diesel generator set during rainy season round the clock including general maitenance as
Per Day - 1,588.00
and when required as per norms prescribed by the manufacturer.
9 Oiling & Greasing of all Gears of Gantry Crane, Bearings,Trolley pulley,Lifting Beam Pulley,Lifting
beam Rollers,warm reducer Gear boxes,Trolly wheels,bracks,wheels including removing old grease after Per Tonne 515.00
removing necessary covers ,and washing by H.S. diesel,refitting of all covers including applying
Cardium compound on wire ropes

97 MISCELLANEOUS WORKS B
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

Item Complete Labour

Description Per / unit
No Rate Rate
10 Under Water visual inspection of upstream wall, Gates & Gate Grooves of major Dam up to 40 meter
water depth using submersible remotely operated vehicle (ROV), including : ROV, Tethers, Command
Module, Operating crew, Additional: Turbid water module etc. The work also includes depth wise video
indicating condition of track and damaged portions, Processed Data with Geo-tagging with detailed P.Sqm 163.00
software report in Pen drive, depth wise report prepared in hard copy(3 sets),
Mobilization/Demobilization of crew and equipment, etc complete in all respect.(Including 18% GST)

11 Supply of Diesel engine driven self-priming Pump sets (Mud Pumps). Diesel Engine as per IS 11170 (Amended upto
date) directly coupled to Self-priming pump through a flexible coupling mounted on a common sturdy and robust 5''
wheeled C.1./Fabricated M.S. Plate trolley manufactured by Pump Manufacturer. The base plate should be designed to
withstand load and vibrations of complete unit. After proper alignment of unit base plate should not cause accidental
breakage.Make of Engine- Kirloskar/Fieldmarshal/Petter/Greaves/Eicher/Cummins Accessories shall also be provided as
per Tender Document. Engine Specifications Rated Power- 15 HP, Cooling-A/C, Rating Speed -1500rpm, Bush Bearing-
, 1 No. Cylinder, 9 Liter Fuel tank Capacity • Self- Priming type Non-Clog Pump suitable for dewatering and lifing
muddy water. Delivery Casing : Grey cast iron of grade FG:200 as per IS: 210-1978 , Impeller : Stainless Steel CF8M as
per IS-6603 (amended or revised up to date), impeller should be dynamically balanced and keyed to the shaft passage
provided through hubs, to give hhydraulic balance and also to relieve stuffing box from any untoward loads. the
Impeller should open type to handle muddy water, Shaft Sleeve : Bronze grade LTB-2 of IS 318-1981 or Chrome Steel Nos. 1,37,645.00
07gr 13 of IS : 1570 part (B) 1986, Stuffing Box : Gray cast iron of grade a FG:200 as per IS 210-1978 water sealed or
mechanically sealed, Gland : Gray cast iron of Grade FG: 200 as per IS: 210-1978, SHAFT. Class 3A-IS 1675 Bush :-
Bronze grade LTBZ.3 or 4 of IS 318 or Nitrile/of less rubber Duty 15HP, Cooling A/c, 1500RPM, Self Primimg Non
Clog Pump, Suction Head- 6m, 18 m Delivery Head, 31.2 LPS Discharge, Suction and delivery pipe should be in
accordance with IS 15265:2003 The Accessories shall also be supplied- 95mm or 114.3 MM mm or equivalent Air cooled
engine coupled with 4''x4'' Non-Clog Centrifugal Pump on M.S. Base Frame with 4'' Wheels. Bend 4'', Hose Nipple 4'',
Heavy Green Suction Hose Pipe 4'', Heavy Green Suction Hose Pipe 4'' For Delivery, Foot Walve 4'', Clips. Complete in
all respect as per Technical Specification.

12 Supply of Diesel engine driven self-priming Pump sets (Mud Pumps). Diesel Engine as per IS 11170 (Amended upto
date) directly coupled to Self-priming pump through a flexible coupling mounted on a common sturdy and robust 5''
wheeled C.1./Fabricated M.S. Plate trolley manufactured by Pump Manufacturer. The base plate should be designed to
withstand load and vibrations of complete unit. After proper alignment of unit base plate should not cause accidental
breakage.Make of Engine- Kirloskar/Fieldmarshal/Petter/Greaves/Eicher/Cummins Accessories shall also be provided as
per Tender Document. Engine Specifications Rated Power- 25 HP, Cooling-W/C, Rating Speed -1500rpm, Bush Bearing-
, 2 No. Cylinder, 20 Liter Fuel tank Capacity • Self- Priming type Non-Clog Pump suitable for dewatering and lifing
muddy water. Delivery Casing : Grey cast iron of grade FG:200 as per IS: 210-1978 , Impeller : Stainless Steel CF8M as
per IS-6603 (amended or revised up to date), impeller should be dynamically balanced and keyed to the shaft passage
provided through hubs, to give hhydraulic balance and also to relieve stuffing box from any untoward loads. the
Impeller should open type to handle muddy water, Shaft Sleeve : Bronze grade LTB-2 of IS 318-1981 or Chrome Steel Nos. 3,06,178.00
07gr 13 of IS : 1570 part (B) 1986, Stuffing Box : Gray cast iron of grade a FG:200 as per IS 210-1978 water sealed or
mechanically sealed, Gland : Gray cast iron of Grade FG: 200 as per IS: 210-1978, SHAFT. Class 3A-IS 1675 ,Bush :-
Bronze grade LTBZ.3 or 4 of IS 318 or Nitrile/of less rubber Duty 25HP, Cooling W/c, 1500RPM, Self Primimg Non
Clog Pump, Suction Head- 6m, 20 m Delivery Head, 43.10 LPS Discharge, Suction and delivery pipe should be in
accordance with IS 15265:2003, The Accessories shall also be supplied - Water cooled 114.3 MM Bore double Cylinder
Engine with radiator cooled electric self start coupled with 6''x6'' Non-Clog Centrifugal Pump on M.S. Base Frame with
4'' Wheels. Bend 6'', Hose Nipple 6'', Heavy Green Suction Hose Pipe 6'', Heavy Green Suction Hose Pipe 6'' For
Delivery, Foot Walve 6'', Clips. Complete in all respect as per Technical Specification.

98 MISCELLANEOUS WORKS B
 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER -XIX

COMPENSATION OF PROPERTIES
GENERAL NOTES FOR ALL COMPENSATION PART:
1 The owners shall be allowed to lift the usable material and trees free of cost.
2 Payment of compensation of Pucca house to be taken up from other relevant chapter of BSR by
measurement of individual item exist in house.
3 The awards issued prior to issue of this BSR shall not be affected.
4 These rates of compensation shall be applicable on properties for which Gazzette notification under
relevant section of prevaling Land Acquisition Act published after issuance of this BSR.
PART A : COMPENSATION OF KATCHA HOUSES
1 Rate for compensation of item No.1 to 9 is for following specifications
I Mud flooring
ii Mud plastered walls.
iii Frame work of M.P. Teak wood Grade-II
iv Wood work shutters of Babool/country wood.
Increase/
Category
Rate in decrease in rates
S.No. Item of Unit
Rs for 5 cm ht.or
houses.
part thereof.
1 Single country tile roofing resting over brick masonry
in mud mortar for standard height 2.85 m.
(a) Complete rate A Per sqm of 6992 61
plinth area
(b) Without wood work Per sqm of 6591 58
plinth area
(c) Without wood work & roofing Per sqm of 5927 52
plinth area
2 Single country tile roofing resting over stone masonry
in mud mortar for standard height 2.85 m
(a) Complete rate B Per sqm of 5642 49
plinth area
(b) Without wood work Per sqm of 5327 47
plinth area
(c) Without wood work & roofing Per sqm of 4756 42
plinth area
3 Single country tile roofing resting over mud walls for
standard height 2.15 m.
(a) Complete rate C Per sqm 1932 18
(b) Without wood work Per sqm 1611 15
(c) Without wood work & roofing Per sqm 1338 12
Chabutara with dry stone masonry wall on three side Per sqm 711
and one side attached with main house wall with
standard height 0.50 m
5 Mud wall in mud mortar for boundary walls of Per RM 503 50
thickness 15 cm. To 22.50 cm with standard height of
1.50 m from G.L.
6 Mud wall in mud mortar for boundary wall of Per RM 671 22
thickness 22.50 cm to 30.00 cm with standard height
of 1.50 m from G.L.

99 COMPENSATION KATCHA HOUSES

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

7 Katcha House of Dry Stone wall with stone Patti

roofing resting over Mud/Dry stone walls for height
of 2.85 m
(a) With wood work Per sqm of 5661 23
plinth area
(b) Without wood work Per sqm of 5227 23
plinth area
8 Compensation of Katcha houses with C.G.I. roofing
resting over dry stone wall in for height of 2.15 m.
(a) With wood work Per sqm of 5013 23
plinth area
(b) Without wood work Per sqm of 4578 23
plinth area
9 Sheds attached with houses covered with C.G.I. Per sqm of 940 2
sheets & resting over stone Patties /angle / iron plinth area
pipes/ballies etc. of 2.15 m. height without foundation
complete.
10 Measurement of Kucha Houses for compensation Per Houses 487.00
estimate purpose complete etc like plinth area
measurement of house/actual measurement of wood
work, bara courtyard plot area etc complete including
preparation of Drawing of each indivisual House in
soft and hard copy, superimposing house drawing on
Village map and prepare individual estimate for
compensation purpose & prepare details of section(4)
of land acquisition act in 6 hard copies and master
copy

11 Measurement of puccha Houses for compensation Per sqm of 22.00

purpose including checking of foundation etc. Plinth Area
copmlete and to prepare estimate including
preparation of Drawing of each individual House in
soft and hard copy, superimposing house drawing on
Village map and prepare individual estimate for
compensation purpose & prepare details of section(4)
of compensation act in 6 hard copies and master copy

12 Measurement of Bara/Chowk including preparation of Per sqm 0.44

Drawing of each indivisual Bara/Chowk in soft and
hard copy, superimposing Bara/Chowk drawing on
Village map and prepare individual estimate for
compensation purpose & prepare details of section(4)
of land acquisition act in 6 hard copies and master
copy

13 Measurement of well and attached accessories Per well 277.00

including marking of well ,indentification from
revenu record and local enquiry including preparation
of Drawing of each indivisual Well in soft and hard
copy, superimposing Well drawing on Village map
and prepare individual estimate for compensation
purpose & prepare details of section(4) of land
acquisition act in 6 hard copies and master copy

100 COMPENSATION KATCHA HOUSES

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

14 Video graphy of each village including all salient

Geological features like Nallah, Hillock, etc. of
village and Houses,including taking photograph from
two angles, displaying house number and Name of
house owner on each photograph (three copies each).
(a) Village having upto 50 houses Each Village 4460.00
(b) Village 51 houses to 100 house Each Village 8200.00
(c) Village 101 houses to 200 houses Each Village 11940.00
(d) Village 201 houses to 300 houses Each Village 19420.00
15 Preparation of List of population after Publishing of Per Houses 102.00
section 11 for affected/ Displaced persons as per
gender male female and as per age group above and
below 18 year as per direction of engineer in charge
along with listing the affected/ displaced families as
per house no. by their name and collect the Aadhar
card, voter id, Ration card, Bhamashah card or any
other documents due to Birth, age, No. of each
document mention in list including collection of the
information of pashubada petty shop etc as per house
number for Project only

101 COMPENSATION KATCHA HOUSES

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER -XIX

PART B : COMPENSATION OF PUCCA HOUSES

NOTES:
1 These rates are inclusive of all lead and lifts of the material scaffolding, cantering,
shuttering required for construction of building.
2 The owners of property and land shall be allowed to lift the usable material and trees
free of cost.
3 These rates of compensation shall be applicable on properties for which Gazette
notification under relevant section of Land Acquisition Act published after issuance of
4 this BSR.
For electrical fittings/ installation @ 3.50% extra shall be payable.
5 The sanitary fitting @ 7% extra will be payable.
6 The rates mentioned are inclusive of depreciation on the houses. No further reduction
on account of depreciation is required.

Rate (in
S.No. Items Unit
Rs)

1 Rate for compensation of Pucca house including

excavation, masonry work plaster work in any mortar,
flooring, roofing wood work etc. complete in all
respect as per standard specification for standard height
of 3.00 m.
a Normal finish and average condition and 3 m. height Per sqm of 7999.00
plinth area
b If C.G.I. Sheet roofing is provided in place of Per sqm of 4851.00
Patti/RCC roofing plinth area
c If Kelu roofing is provided in place of Patti / RCC Per sqm of 4940.00
roofing plinth area
d If country tile roofing is provided in place of Patti / Per sqm of 4901.00
RCC roofing plinth area
2 Add/deduct from item No.1 of standard height of 3.0 m
increase/ decreases
a Every 30 cm height above or below 1.50%
3 Rate for masonry compound wall in lime/cement mortar Per RM 1491.00
up to 1.0 m
4 Add extra for each 0.50 m height of boundary wall over Per RM 429.60
item, 3
5 Rate for dry stone masonry compound wall up to 1.0 m Per RM 1270.80

6 Add extra for each 0.50 m height of boundary wall over Per RM 366.00
item, 5
7 Add for platform/courtyard with average flooring Per Sqm 928.00

102 COMPENSATION OF PUCCA HOUSES

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER -XIX

COMPENSATION FOR TEMPORARY LAND ACQUISITION

PART C : TEMPORARY LAND ACQUISITION

S.No. Item Unit Rate in Rs

1 Rate of compensation for temporary land

acquisition.
(a) For Vacant Land during one crop period (For six
months)

i For Command area / Ha 65000.00

ii For Uncommand area / Ha 16000.00
(b) For Land having crop grown for one crop period
(For six months)
i For Command area / Ha 80000.00
ii For Uncommand area / Ha 20000.00

103 TEMPORARY LAND ACQUISITION

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

CHAPTER -XIX

COMPENSATION FOR LAND ACQUISITION

PART D : COMPENSATION OF WELLS.
Notes :-
1 The rates for compensation of wells are for the wells constructed in cement or
lime mortar masonry including excavation in all types of strata and construction
of ancillary structures like Dhana, Kheli, Kundi, platform etc. but excluding
pump house.
2 For pucca pump house the payment shall be made on plinth area basis as per
chapter 19 B
3 These rates are inclusive of all lead and lifts of the material scaffolding,
centring, shuttering required for construction of wells.
4 For intermediate internal diameter and depth cost will be worked out by linear
interpolation
5 The rates are inclusive of digging of wells in dry/moist/ saturated/ wet
conditions including dewatering.
6 The awards issued prior to issuance of this BSR shall not be affected.
7 In case of wells the depth of wells shall be taken from top of lowest masonry
8 However, increase of Dohri the depth shall be calculated considering the
average of highest and lowest of masonry level.
9 In case of Dohri 10% extra on the cost stated in item no (3) shall be paid for
approaches and ancillary work like humps pipe channels, masonry channels,
Kundi etc.
S.No. Item
1 Rate for compensation of cement concrete/RCC/ wells/ Dohri including sinking
or digging of wells in all types of strata and construction of ancillary structures
like Dhana, Kheli, Kundi, Platform etc. excluding pump house as per given
below (Rate in Rs)
Depth below NSL in Metre Internal Diameter in metre
1.5 2 3 4 and above
2 76718 88348 112406 137527
3 96311 113756 149842 187524
4 116001 139312 187564 237986
5 135740 164943 225427 288681
6 159448 195622 270462 348626
7 179937 222230 309782 401290
8 200474 248913 349245 454186
9 227160 283464 400034 521888
10 248229 310791 440313 575705
11 269566 338525 481375 630801
12 299084 376726 537490 705561
13 320881 404993 579154 761230
14 343016 433779 621814 818528
15 375367 475631 683257 900346
16 397889 504838 726305 957867
17 420824 534676 770566 1017365
18 456007 580178 837334 1106243
19 479256 610325 881768 1165616
20 502988 641215 927627 1227315

104 COMPENSATION OF WELLS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

2 Rate for compensation of cement or lime mortar masonry wells including

excavation in all types of strata and construction of ancillary structures like
Dhana, Kheli, Kundi, Platform etc. excluding pump house as per given below
(Rate
Depthin Rs) NSL in Metre
below Internal Diameter in metre
1.5 2 3 4 and above
2 56313 68903 94881 121923
3 68332 84589 118297 153602
4 80449 100423 141999 185746
5 92614 116330 165842 218124
6 109135 137782 197568 260676
7 122114 154749 222986 295176
8 135143 171793 248547 329908
9 154901 197447 286499 380835
10 168526 215214 312994 416642
11 182417 233392 340272 453730
12 205266 263026 384024 512330
13 219682 281816 412023 550145
14 234438 301129 441018 589587
15 260377 334742 490571 655864
16 275583 354556 520073 695683
17 291203 375003 550786 737481
18 320233 412596 606140 811433
19 336230 433433 637144 853260
20 352712 455014 669574 897412
3 Rate for compensation of dry stone masonry wells including excavation in all
types of strata and construction of ancillary structures like Dhana, Kheli, Kundi,
Platform etc. excluding pump house as per given below (Rate in Rs)
Depth below NSL in Metre Internal Diameter in metre
1.5 2 3 4 and above
2 16912 22264 33767 46334
3 25144 33111 50241 68967
4 33473 44107 67000 92065
5 41851 55176 83901 115396
6 52714 69395 105252 144431
7 61595 81127 123156 169138
8 70524 92932 141202 194080
9 83375 109761 166493 228506
10 92590 121892 184900 253777
11 102071 134434 204092 280328
12 116765 153648 232894 319448
13 126457 166404 252234 345979
14 136490 179681 272571 374139
15 153026 201281 304885 417954
16 163199 214661 325157 445746
17 173783 228674 346638 475516
18 192162 252658 382466 524024
19 202812 266663 403668 553077
20 213949 281412 426296 584457

105 COMPENSATION OF WELLS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

4 Rate for compensation exclusively for digging of Katcha well in all type of
strata as per table given below rate in Rs
Depth below NSL in Metre Internal Diameter in metre
2 3 4 and above
2 1197 2127 4787 8511
3 1795 3192 7181 12766
4 2443 4344 9772 17373
5 3115 5540 12463 22157
6 3740 6647 14955 26588
7 4449 7909 17795 31635
8 5183 9214 20733 36858
9 5943 10564 23770 42257
10 6603 11737 26411 46952
11 7399 13154 29596 52615
12 8220 14614 32880 58455
13 8905 15831 35620 63325
14 9763 17357 39053 69428
15 10646 18927 42585 75707
5 Rate for compensation of Precast RCC Ring wells including sinking or digging
of wells in all types of strata and construction of ancillary structures like Dhana,
Kheli, Kundi, Platform etc. excluding pump house as per given below (Rate in
Rs)

Depth below NSL in Metre Internal Diameter in metre

1.5 2
2 11563 15313
3 17345 22970
4 23224 30776
5 29150 38655
6 34980 46387
7 40981 54378
8 47030 62444
9 53126 70584
10 59029 78426
11 65199 86678
12 71416 95003
13 77368 102921
14 83659 111358
15 89997 119869
16 95998 127861
17 102410 136484
18 108870 145181
19 114919 153246
20 121452 162056

106 COMPENSATION OF WELLS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

6 Compensation of Tube-well constructed in alluvial strata, over burden and in all

type of rock and tube well having casing pipes and diameters as under. The
bore of tube well considered similar to nominal dia of casing pipe
A - MS Black Casing Pipe
(i) Upto 30 Meter depth
Nominal bore 150mm dia a each 46005
Nominal bore 200 mm dia b each 66606
(ii) Above 30 Metre and upto
50 Meter depth
Nominal bore 150mm dia a each 61827
Nominal bore 200 mm dia b each 89670
(iii) Above 50 Metre and upto
70 Meter depth
Nominal bore 150 mm dia a each 82937
Nominal bore 200 mm dia b each 105046
(iv) Above 70 Metre and upto
100 Meter depth
Nominal bore 150mm dia a each 88197
Nominal bore 200 mm dia b each 128111
(v) Above 100 Metre depth
Nominal bore 150mm dia a 98745
Nominal bore 200 mm dia b each 143487
B- AC/PVC casing pipe each
(i) Upto 30 Meter depth
Nominal bore 150mm dia a each 24542
Nominal bore 200 mm dia b each 39019
(ii) Above 30 Metre and upto
50 Meter depth
Nominal bore 150mm dia a each 40364
Nominal bore 200 mm dia b each 62084
(iii) Above 50 Metre and upto
70 Meter depth
Nominal bore 150 mm dia a each 57564
Nominal bore 200 mm dia b each 77460
(iv) Above 70 Metre and upto
100 Meter depth
Nominal bore 150 mm dia a each 66734
Nominal bore 200 mm dia b each 100524
(v) Above 100 Metre depth
Nominal bore 150mm dia a each 77282
Nominal bore 200 mm dia b each 115900
7 Rate for compensation of
earthwork for bunds for
Doll/Dangar in all type of soil
a Up to 0.30 m height Per RM NIL
b Above 0.30 m to 0.50 m height Per RM 25.20
c Above 0.50 m to 1.00 m height Per RM 94.50
d Above 1.00 m to 1.50 m height Per RM 236.25
e Above 1.50 m height Per RM 283.50

107 COMPENSATION OF WELLS

 BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

ITEM NO.19 ( E) FOR FRUIT BEARING TREES. (RATES IN RS)

MEASUREMENT OF GIRTH IN CM OF THE FRUIT BEARING TREE IN CMS. (Perimeter of Stem)
331-
10 20 21-30 20-35 10- 30 31-60 61-80 81-120 121-150 151-180 181-210 211-240 241-270 271-300 301-320
Above.
AAM DESI - - - 1811 2085 2603 3829 5243 6035 6864 7656 8485 9281 10146 11032
AAM KALMI - - - 3034 3382 3971 5205 6524 7206 8034 8882 9713 10561 11372 12013
AMROOD - - - 1319 1962 2564 - - - - - - - - -
NIMBO 1057 - 1471 - - - - - - - - - - - -
SITAFAL 368 - 490 - - - - - - - - - - - -
IMALI - - - 218 489 1008 2155 3382 4038 4811 5546 6281 7017 7694 8335
ANAR 924.0156 1655.6904 - - 1716 - - - - - - - - - -
KARONDA 536.7348 752.4684 - - 982 - - - - - - - - - -
AMALA - - - 1275 1819 2114 3395 4754 - - - - - - -
KRINTH - - - 180 390 933 1811 2999 3528 - - - - - -
LASODA - - - 811 1399 1847 2965 4452 5000 - - - - - -

MEASUREMENT OF GIRTH IN CM OF THE FRUIT BEARING TREE IN CMS. (Perimeter of Stem)

NAME OF TREES
12-20 21 - 30 31 - 46 47 - 61 62 - 76 77 - 91 92 - 107 108 - 122 123 - 137 138 - 152 152 cm above.
Trees not included i.e
Neem, Babul, Ardu and 71 113 190 342 683 1021 1898 2608 3156 3512 4148
Khajur and similar tree

NAME OF TREES Girth up to 10 cm Ht. 3 to 4 m. Girth up to 12 cm Ht. up to 5 m. Girth up to 15 cm Ht. up to 5 m

Bamboo Tree 33 58 71
FOR ORANGE TREES. (RATES IN RS)
NAME OF TREES MEASUREMENT OF ITEM OF THE FRUIT BEARING TREE IN CMS. (Perimeter of Stem)
5 cm to 7.5 cm or > 7.5 cm to 12.5 cm or (> > 12.5 cm to 20 cm or (> > 20 cm to 35 cm or > 35 cm to 45 cm or > 45 cm or (> 18")
(> 2" to 3") 3" to 5") 5" to 8") (> 8" to 14") (>14" to 18")
1 2 3 4 5 6 7
ORANGE 295 590 880 1172 2778 4100
Note :- 1. Measurement of the perimeter of stem should be measured within 15 cm from ground level.

108 FRUIT BEARING TREES

BASIC SCHEDULE OF RATES WATER RESOURCES DEPARTMENT KOTA ZONE

ANNEXURES
I to XII

109
 BASIC SCHEDULE OF RATESWATER RESOURCES DEPARTMENT JAIPUR DISTRICT

Annexure I
LIST OF RELEVANT IS CODES

1. GEOLOGICAL INVESTIGATION AND SUBSURFACE EXPLORATION

1 IS 10060 : 2013 Geotechnical investigation for power house sites - Code of practice (First Revision)
2 IS 10290 : 1982 Code of practice for photogeological interpretation and mapping of river valley project sites
Subsurface exploration for canals and cross drainage works - Code of practice (First
3 IS 11385 : 2008
Revision)
4 IS 13216 : 1991 Code of practice for geological exploration for reservoir sites
5 IS 13578 : 2008 Subsurface exploration for barrages and weirs - Code of practice (First Revision)
6 IS 14330 : 1996 Ground water investigation for hydraulic structures - Guidelines
7 IS 15662 : 2006 Geological exploration for gravity dams and overflow structures - Code of practice
8 IS 15681 : 2006 Geological exploration by geophysical method (Seismic Refraction) - Code of practice
Recommendations for preparation of geological and geotechnical maps for river valley
9 IS 15686 : 2006
projects
10 IS 15736 : 2007 Geological exploration by geophysical method (Electrical Resistivity) - Code of practice
11 IS 4078 : 1980 Code of practice for indexing and storage of drill cores (First Revision)
IS 4410 : Part 7 Glossary of terms relating to river valley projects: Part 7 engineering geology (First
12
: 1982 Revision)
Subsurface exploration by pits, trenches, drifts and shafts - Code of practice (Second
13 IS 4453 : 2009
Revision)
Code of practice for presentation of drilling information and core description in foundation
14 IS 4464 : 1985
investigation (First Revision)
15 IS 5313 : 1980 Guide for core drilling observations (First Revision)
16 IS 5497 : 2008 Guide to topographical surveys for river valley projects (Second Revision)
17 IS 5529 Part 1 : In-situ permeability test Part 1 Test in overburden - Code of practice
18 2013
IS 5529 : Part 2 In - Situ permeability test: Part 2 tests in bedrock (Second Revision)
19 : 2006
IS 6926 : 1996 Diamond core drilling - Site investigation for river valley projects - Code of practice (First
20 revision)for determination of water level in a bore hole
IS 6935 : 1973 Method
21 IS 6955 : 2008 Subsurface exploration for earth and rockfill dams - Code of practice (First Revision)
22 IS 7422 : Part 1 Symbols and abbreviations for use in geological Maps: Section and subsurface exploratory
23 :IS1974
7422 : Part 2 logs: Partand
Symbols 1 abbreviations
abbreviations for use in geological maps: Section and subsurface exploratory
:IS1974
7422 : Part 3 logs: Part
Symbols and2 igneous rocks for use in geological maps: Sections and subsurface
abbreviations
25 : 1974
IS 7422 : Part 4 exploratory
Symbols andlogs: Part 3 sedimentary
abbreviations for use inrocks
geological maps: Sections and subsurface
26 : 1985
IS 7422 : Part 5 exploratory
Symbols andlogs: Part 4 metamorphic
abbreviations for use in rocks
geological maps: Sections and sub - Surface
: 1992 exploratory logs: Part 5 line symbols for formation contacts and structural features
2. WATER RESOURCES PLANNING, MANAGEMENT AND EVALUATION

1 IS 10336 : 1982 Guidelines for preparation of completion reports of multipurpose river valley projects
2 IS 13028 Part 1 Guidelines for integrated planning, development and management of river basins: Part 1
3 : 2014
IS overall planning
13142 : 1991 Proforma (First Revision)
for reporting progress of benefits created by river valley projects
4 IS 13218 : Part Proforma for reporting progress during construction for river valley projects: Part 1 irrigation
5 1 : 13218
IS 1992 : Part Proforma
works for reporting progress during construction for river valley projects: Part 2 hydel
6 2 : 1991 works
IS 13218 : Part Proforma for reporting progress during construction for river valley projbcts: Part 3 flood
7 3 : 13668
IS 1992 : 1993 Guidelines
control for fixing intensity of irrigation
8 IS 13739 : 1993 Guidelines for estimation of flood damages
9 IS 14519 : 1998 Guidelines for fixing rates for irrigation water
10 IS 15087 : 2001 Planning and design of drainage in irrigation projects - Guidelines
11 IS 16115 : 2013 Evaluation of completed irrigation projects (Major And Medium) - Guidelines
12 IS 4008 : 1985 Guide for presentation of project report for river valley projects (First Revision)
13 IS 4186 : 1985 Guide for preparation of project report for river valley projects (First Revision)
14 IS 4410 : Part 1 Glossary of terms relating to river valley projects: Part 1 irrigation practice (First Revision)
15 :IS1991
4410 : Part Glossary of terms relating to river valley projects: Part 11 hydrology: Sec 5 floods
16 11 : Sec :5Part
IS 4410 : Glossary of terms relating to river valley projects: Part 14 soil conservation and
14 : Sec 1 : reclamation: Sec 1 soil conservation
 BASIC SCHEDULE OF RATESWATER RESOURCES DEPARTMENT JAIPUR DISTRICT

17 IS 4410 : Part Glossary of terms relating to river valley projects: Part 14 soil conservation and
18 14 : Sec :2Part
IS 4410 : reclamation: Sec 2relating
Glossary of terms reclamation
to river valley projects: Part 17 water requirements of crops
19 17 : 1977
IS 4410 : Part 2 Glossary of terms relating to river valley projects: Part 2 project planning
20 :IS1967
4410 : Part Glossary of terms relating to river valley projects: Part 21 flood control
21 21 4410
IS : 1987: Part 4
Glossary of terms relating to river valley projects: Part 4 drawings (First Revision)
22 : 1982
IS 5510 : 1969 Guide for soil surveys for river valley projects
23 IS 6748 : Part 1 Recommendations for watershed management relating to soil conservation: Part 1
24 : 1973
IS agronomic aspects
7560 : 1974 Guidelines for allocation of cost among different purposes of river valley projects

3. FOUNDATION AND SUBSTRUCTURES

1 IS 11293 : 2018 Guidelines for the design of grout curtains for earth and rock fill dams, masonry dams and
2 IS 11293 : Part concrete gravity
Guidelines dams
for the design of grout curtains: Part 1 earth and rockfill dams
3 1 : 11293
IS 1985 : Part Guidelines for the design of grout curtains: Part 2 masonry and concrete gravity dams
4 2 : 1993 : 1986
IS 11973 Code of practice for treatment of rock foundations, core and abutment contacts with rock,
5 for embankment
IS 12584 : 1989 Bentonite damsin civil engineering works - Specification
for grouting
6 IS 14343 : 1996 Choice of grouting, materials for alluvial grouting - Guidelines
7 IS 14344 : 1996 Design and construction of diaphragms for under - Seepage control - Code of practice
8 IS 16547 : 2017 Investigations for foundation of existing earth and rock fill dams - Guidelines
9 IS 4410 : Part Glossary of terms relating to rivervalley projects: Part 19 grouting
10 19 4999
IS : 1996: 1991 Recommendations for grouting of pervious soils (First Revision)
11 IS 5050 : 1992 Code of practice for design, construction and maintenance of relief wells (First Revision)
12 IS 6066 : 1994 Pressure grouting of rock foundations in river valley projects - Recommendations (Second
13 IS 8414 : 2014 Revision)
Guidelines for design of under seepage control measures for earth and rockfill dams (First
Revision)
4. DAMS AND SPILLWAYS

1 IS 10135 : 1985 Code of practice for drainage system for gravity dams, their foundations and abutments
2 IS 10137 : 2015 (First Revision)
Guidelines for selection of spillways and energy dissipators (First Revision)
3 IS 10635 : 2014 Freeboard requirement in dams - Guidelines (Second Revision)
4 IS 11155 : 2019 Construction of spillways and similar overflow structures - Code of practice (Second
5 IS 11216 : 1985 Revision)
Code of practice for permeability test for masonry during and after construction
6 IS 11223 : 1985 Guidelines for fixing spillway capacity
7 IS 11485 : 2014 Criteria for design of sluices in concrete and masonry dams (First Revision)
8 IS 11527 : 2013 Structural design of energy dissipators for spillways - Criteria (First Revision)
9 IS 11772 : 2009 Design of drainage arrangements ofenergy dissipators and training walls of spillways -
10 IS 12169 : 1987 Guidelines
Criteria (First Revision)
for design of small embankment dams
11 IS 12200 : 2001 Provision of water - Stops at transverse contraction joints in masonry and concrete dams -
12 IS 12720 : 2004 Code offor
Criteria practice (First
structural Revision)
design of spillway training walls and divide walls (Second Revision)
13 IS 12731 : 1989 Hydraulic design of impact type energy dissipators - Recommendations
14 IS 12804 : 1989 Criteria for estimation of aeration demand for spillway and outlet structures
15 IS 12966 : Part Code of practice for galleries and other openings in dams: Part 1 general requirements
16 1
IS: 12966
1992 : Part Code of practice for galleries and other openings in dams: Part 2 structural design
17 2 : 1990 : 1991
IS 13048 Recommendations for hydraulic design of duck bill spillways
18 IS 13144 : 1991 Recommendations for provision of facilities outside the dams
19 IS 13195 : 1991 Preliminary design, operation and maintenance of protection works downstream of
20 spillways -design
IS 13551 : 1992 Structural Guidelines
of spillway pier and crest - Criteria
21 IS 13645 : 1993 Guniting the upstream face of masonry dams - Guidelines
22 IS 14591 : 1999 Temperature control of mass concrete for dams - Guidelines
23 IS 14690 : 1999 Quality control during construction of earth and rockfill dams - Recommendations
24 IS 14954 : 2001 Distress and remedial measures in earth and rockfill dams - Guidelines
25 IS 15058 : 2002 PVC water - Stops at transverse contraction joints for use in masonry and concrete dams -
26 Specification
IS 4410 : Part Glossary of terms relating to river valley projects: Part 18 energy dissipation devices
27 18 4410
IS : 1983: Part 8 Glossary
(Stilling Basins)
of terms relating to river valley projects: Part 8 dams and dam: Section (First
: 1992 Revision)
 BASIC SCHEDULE OF RATESWATER RESOURCES DEPARTMENT JAIPUR DISTRICT

28 IS 4410 : Part 9 Glossary of terms relating to river valley projects: Part 9 spillways and siphons (First
29 : 1982
IS 4997 : 1968 Revision)
Criteria for design of hydraulic jump type stilling basins with horizontal and sloping apron
30 IS 5186 : 1994 Design of chute and side channel spillways - Criteria (First Revision)
31 IS 6512 : 2019 Criteria for design of solid gravity dams (Second Revision)
32 IS 6934 : 2014 Hydraulic design of high ogee overflow and orifice spillways - Recommendations (Second
33 IS 7365 : 2010 Revision)
Criteria for hydraulic design of bucket type energy dissipators (Second Revision)
34 IS 7894 : 1975 Code of practice for stability analysis of earth dams
35 IS 8605 : 1977 Code of practice for construction of masonry in dams
36 IS 8826 : 1978 Guidelines for design of large earth and rockfill dams
37 IS 9296 : 2001 Inspection and maintenance of dams and appurtenant structures - Guidelines (First
38 IS 9297 : 1979 Revision)
Recommendations for lighting, ventilation and other facilities inside dams
39 IS 9429 : 1999 Drainage system for earth and rockfill dams - Code of practice (First Revision)
40 SP 55 : 1993 Design aid for anchorages for spillway piers, training walls and divide walls

5. RESERVOIR AND LAKES

1 IS 12182 : 1987 Guidelines for determination of effects of sedimentation in planning and performance of
2 IS 13665 : 2017 reservoirs - Methods for assessment of reservoir sedimentation (First Revision)
Hydrometry
3 IS 14654 : 1999 Minimising evaporation losses from reservoirs - Guidelines
4 IS 15472 : 2004 Guidelines for planning and design of low level outlets for evacuating storage reservoirs
5 IS 15840 : 2009 Determination of volume of water and water level in lakes and reservoirs
6 IS 4410 : Part 6 Glossary of terms relating to river valley projects: Part 6 reservoirs (First Revision)
7 :IS1983
5477 : Part 1 Fixing the capacities of reservoirs methods: Part 1 general requirements (First Revision)
8 :IS1999
5477 : Part 2 Fixing the capacities of reservoirs - Methods: Part 2 dead storage (First Revision)
9 : 1994
IS 5477 : Part 3 Fixing the capacities of reservoirs - Methods: Part 3 live storage (First Revision)
10 : 2002
IS 5477 : Part 4 Methods for fixing the capacities of reservoirs: Part 4 surcharge storage (First Revision)
11 :IS2019
6518 : 2017 Guidelines for control of sediment in reservoirs (Second Revision)
12 IS 6939 : 1992 Methods for determination of evaporation from reservoirs (First Revision)
13 IS 7323 : 1994 Operation of reservoirs - Guidelines (First Revision)
14 IS 8237 : 1985 Code of practice for protection of slope for reservoir embankment (First Revision)

6. HYDRAULIC GATES AND VALVES

1 IS 10021 : 2000 Guidelines for de - Icing system for hydraulic installations (First Revision)
2 IS 10096 : Part Recommendations for inspection; testing and maintenance of radial gates and their hoists:
3 1
IS: 10096
Sec 1 :: 2014
Part Part I inspection, testing
Recommendations and assembly
for inspection, at and
testing the manufacturing
maintenance ofstage:
radialSection I gates
gates and their hoists:
4 2 : 1983 : Part
IS 10096 Part 2 inspection, testing and assembly at the time of erection
Recommendations for inspection, testing and maintenance of radial gates and rope drum
5 3 : 10096
IS 2002 :Part hoists: Part 3 after erection
Recommendations (Second
for inspection, Revision)
testing and maintenance of radial gates and rope drum
6 1 : 10210
IS Sec 2 :: 2014
1993 hoists: Part
Criteria 1 inspection,
for design testing
of hydraulic and assembly
hoists at theRevision)
for gates (First manufacturing stage: Sec 2 rope
7 IS 11228 : 1985 Recommendations for design of screw hoists for hydraulic gates
8 IS 11793 : 1986 Guidelines for design of float driven hoisting mechanism for automatic gated control
9 IS 11855 : 2017 Design and use of rubber seals for hydraulic gates - Recommendations (Second Revision)
10 IS 13041 : 2013 Recommendations for inspection, testing and maintenance of hydraulic hoist (After
11 IS 13591 : 2019 Erection)
Criteria for(First Revision)
design of lifting beams (First Revision)
12 IS 13623 : 1993 Criteria for choice of gates and hoists
13 IS 14177 : 1994 Guidelines for painting system for hydraulic gates and hoists
14 IS 15466 : 2004 Rubber seals for hydraulic gates - Specification
15 IS 4410 : Part Glossary of terms relating to river valley projects: Part 16 gates and valves: Sec 1 gates
16 16 : Sec :1Part
IS 4410 : and Terms
Glossary ofrelated with gates
terms relating (Firstvalley
to river Revision)
projects: Part xvi gates and valves: Sec 2 valves
17 16 : Sec 2 :
IS 4410 : Part Glossary of terms relating to river valley projects
18 23 4622
IS : 1999: 2003 Recommendations for structural design of fixed - Wheel gates (Third Revision)
19 IS 4623 : 2000 Recommendations for structural design of radial gates (Third Revision)
20 IS 5620 : 1985 Recommendations for structural design criteria for low head (Second Slide Gates Revision)
21 IS 6938 : 2005 Design of rope drum and chain hoists for hydraulic gates - Code of practice (Second
Revision)
 BASIC SCHEDULE OF RATESWATER RESOURCES DEPARTMENT JAIPUR DISTRICT

22 IS 7326 : Part 1 Penstock and turbine inlet butterfly valves for hydropower stations and systems: Part 1
23 :IS1992
7326 : Part 2 criteria
Penstock forand
structural
turbineand
inlethydraulic
butterflydesign
valves (First Revision)
for hydro - Power stations and systems: Part 2
24 :IS1992
7326 : Part 3 guidelines for design and selection of control
Penstock and turbine inlet butterfly valves for hydropower stations and systems: Part 3
25 :IS1976
7332 : Part 1 recommendations
Spherical valves for forhydropower
operations stations
and maintenance
and systems: Part 1 criteria for structural and
26 : 1991
IS 7332 : Part 2 hydraulic design
Spherical valves (First Revision) stations and systems: Part 2 selection of control
for hydropower
27 : 1993
IS 7332 : Part 3 equipmentvalves
Spherical (First Revision)
for hydropower stations and systems: Part 3 recommendations for
28 :IS19947718 : 2018 operation and maintenance
Recommendations of spherical
for inspection, testingvalves (First Revision)
and maintenance of fixed wheel and slide gate
29 IS 9349 : 2006 (Second Revision)
Recommendations for structural design of medium and high head slide gates (Second
Revision)
7. CANALS AND CD WORKS

1 IS 10430 : 2000 Criteria for design of lined canals and guidance for selection of type of lining (First
2 IS 10646 : 1991 Revision)
Canal linings - Cementconcrete tiles - Specification (First Revision)
3 IS 11570 : 1985 Criteriafor hydraulic design of irrigation intake structures
4 IS 11809 : 1994 Lining for canals by stone masonry - Code of practice (First Revision)
5 IS 12331 : 1988 General requirements for canal outlets
6 IS 12379 : 1988 Code of practice for lining of water - Courses and field channels
7 IS 13143 : 1991 Joints in concrete lining of canals - Sealing compound - Specification
8 IS 16238 : 2017 Planning of parallel canals - Guidelines
9 IS 16472 : 2016 Design and construction of water courses - Guidelines
10 IS 3872 : 2002 Lining of canals with burnt clay tiles - Code of practice (First Revision)
11 IS 3873 : 1993 Laying .cement concrete/stone slab lining on canals - Code of practice (Second Revision)
12 IS 4410 : Part Glossary of terms relating to river valley projects: Part 15 Canal structures Section 1
13 15 : Sec :1Part
IS 4410 : General
Glossaryterms
of terms relating to river valley projects: Part 15 canal structures: Sec 2
14 15 4410
IS : Sec :2Part
: Transitions
Glossary of terms relating to river valley projects: Part 15 canal structures: Sec 3 Flume.
15 15 4410
IS : Sec :3Part
: Glossary of terms relating to river valley projects: Part 15 canal structures: Sec 4
16 15 4410
IS : Sec :4Part
: Regulating
Glossary ofworks
terms relating to river valley projects: Part 15 canal structures: Sec 5 Cross -
17 15 : Sec 5 : 5
IS 4410 : Part Drainage
Glossary of terms(First
Works Revision)
relating to river valley projects: Part v Canals (First Revision)
18 :IS1982
4515 : 2002 Stone pitched lining for canals - Code of practice (Second Revision)
19 IS 4558 : 1995 Under - Drainage of lined canals - Code of practice (Second Revision)
20 IS 4701 : 1982 Code of practice for earthwork on canals (First Revision)
21 IS 4839 : Part 1 Maintenance of canals - Code of practice: Part 1 unlined canals (Second Revision)
22 : 1992
IS 4839 : Part 2 Maintenance of canals - Code of practice: Part 2 lined canals (Second Revision)
23 : 1992
IS 4839 : Part 3 Code of practice for maintenance of canals: Part 3 canal structures, drains, outlets, jungle,
24 :IS1992
5256 : 1992 clearance,
Sealing plantation
expansion andinregulation
joints concrete flining
second revision)
of canals - Code of practice (First Revision)
25 IS 5690 : 1982 Guide for laying combination lining for existing unlined canals (First Revision)
26 IS 5968 : 1987 Guide for planning and layout of canal system for lrrigation (First Revision)
27 IS 6004 : 1980 Criteria for hydraulic design of sediment ejector for irrigation and power channels (First
28 IS 6522 : 1972 Revision)
Criteria for design of silt vanes for sediment control in offtaking canals
29 IS 6531 : 1994 Canal head regulators criteria for design (First Revision)
30 IS 6936 : 1992 Guide for location, selection and hydraulic design of canal escapes (First Revision)
31 IS 7112 : 2002 Criteria for design of cross -: Sec for unlined canals in alluvial soil (First Revision)
32 IS 7113 : 2003 Soil - Cement lining for canals - Code of practice (First Revision)
33 IS 7114 : 1973 Criteria for hydraulic design of cross regulators for canals
34 IS 7331 : 1981 Code of practice for inspection and maintenance of cross drainage works (First Revision)
35 IS 7495 : 1974 Criteria for hydraulic design of silt selective head regulator for sediment control in offtaking
36 IS 7784 : Part 1 canals of cross drainage works - Code of practice: Part 1 general features (Second
Design
37 :IS2013
7784 : Part 2 Revision)
Design of cross drainage works code of practice: Part 2 specific requirements: Sec 1
38 :ISSec 1 : :1995
7784 Part 2 aqueducts (First Revision
Code of practice for designJ of cross drainage works: Part 2 specific requirements: Sec 2
39 :ISSec 2 : :2000
7784 Part 2 superpassages (First
Code of practice for designRevision)
of cross drainage works: Part 2 specific requirements: Sec 3
40 : Sec
IS 3 : :1996
7784 Part 2 canal syphons
Design of cross(First Revision)
drainage works - Code of practice: Part 2 specific requirements: Sec 4
41 : Sec
IS 4 : :1999
7784 Part 2 level crossings
Code of practice(First Revision)
for design of cross drainage works part2 specific requirements: Sec 5
42 :ISSec 5 : 2000
7871 : 1975 syphon aqueducts
Criteria for hydraulic (First Revision)
design of groyne walls (Curved Wing) for sediment distribution at
43 IS 7873 : 1975 offtake points in a canal
Code of practice for limb concrete lining for canals
 BASIC SCHEDULE OF RATESWATER RESOURCES DEPARTMENT JAIPUR DISTRICT

44 IS 7880 : 1975 Criteria for hydraulic design qf skimming platform for sediment control in offtaking canal
45 IS 7986 : 1976 Code of practice for canal outlets
46 IS 8835 : 1978 Guidelines for planning and design of surface drains
47 IS 9097 : 1979 Guide for laying lining of canals with hot bitumen or bituminous felts
48 IS 9447 : 1980 Guidelines for assessment of seepage losses from canals by analytical method
49 IS 9451 : 1994 Guidelines for lining of canals in expansive soils (Second Revision)
50 IS 9452 : Part 1 Measurement of seepage losses from canals - Code of practice: Part 1 Ponding method
51 :IS1993
9452 : Part 2 Code of practice for measurement of seepage losses from canals: Part 2 inflow - O - utflow
52 :IS1980
9452 : Part 3 method
Code of practice for measurement of seepage losses from canals: Part 3 seepage meter
53 IS: 1988
9698 : 1995 methodof canals with polyethylene film - Code of practice (First Revision)
Lining
54 IS 9913 : 2000 Code of practice for construction of cross drainage works (First Revision)

8. HYDRAULIC STRUCTURES INSTRUMENTATION

1 IS 10334 : 1982 Code of practice for selection, splicing, installation and providing protection to the open
2 IS 10434 : Part ends of cables
Installation, used for connecting
maintenance resistance
and observation type measuring
of deformation devices
measuring in concrete
devices and
in concrete
3 1
IS: 10434
2003 : Part and masonry dams - Guidelines: Part 1 resistance type jointmeters (First
Guidelines for installation, maintenance and observation of preformation measuring Revision)
4 2 : 12949
IS 1996 : 2013 devices in concrete
Installation, and masonry
maintenance dams: Part
and observation 2 vibrating, wire
of instruments typepressure
for pore jointmeter measurements
5 IS 13073 : Part in earth and maintenance
Installation, rockfill dams and
- Vibrating wire type
observation electrical pore
of displacement pressure devices
measuring cell - Code of
in concrete
6 1 : 13073
IS 2002 : Part and masonry
Code dams
of practice for-installation,
Code of practice: Part 1 deflection
maintenance measurement
and observation using plumb
of displacement lines
measuring
7 2 : 2000 : 1992
IS 13232 devices for concrete and masonry dams: Part 2 geodetic observation - Crest
Installation, maintenance and observations of electrical strain measuring devices in collimation
8 IS 14248 : 1995 concrete dams
Guidelines - Code of practice
for instrumentation of barrages and weirs
9 IS 14278 : 1995 Stress measuring devices in concrete and masonry dams - Installation, commissioning and
10 IS 14750 : 2014 observations
Code of practice- Code of practice maintenance and observation of seepage measuring
for installation,
11 IS 14793 : 2013 devices for concrete/masonry
Installation, and earth/ rockfill
maintenance and observation of thedams (First Revision)
instruments for vibration studies other than
12 IS 17158 : 2019 earthquakes
Guide for typeonofhydraulic structures
measurement, choiceandofmachines - Code
location and typeofofpractice (Firstfor
instruments Revision)
underground
13 IS 6524 : 1972 powerof
Code house
practice for installation and observation of instruments for temperature
14 IS 6532 : 1972 measurements
Code of practiceinside dams :installation,
for design, resistance observation
type thermometers
and maintenance of uplift pressure
15 IS 7356 : Part 1 pipes for hydraulic structures on permeable
Code of practice for installation, maintenance foundations
and observation of instruments for pore
16 :IS2002
7356 : Part 2pressure measurements
Installation, observation andin earth dams andofrockfill
maintenance dams -for
instruments Part
pore1 : pressure
porous measurements
17 : 2003
IS 7436 : Part 1in earthfort
Guide and rockfill
ypes dams - Code offorpractice:
of measurements Part
structures in2river
twinvalley
tube hydraulic
projects andpiezometers
criteria for
18 : 1993
IS 7436 : Part 2choice for
Guide andtypes
location of measuring instruments:
of measurements for structuresPart 1 forvalley
in river earthprojects
and rockfill
anddams (First
criteria for
19 :IS2019
7500 : 2000 choiceofand
Code location
practice for of measuring
installation andinstrument:
observationPartof2cross
concrete
armsandfor masonry
measurementdamsof(Second
internal
20 IS 8226 : 2017 vertical movement
Installation and in earth
observation dams
of base(First Revision)
plate apparatus for measurement of foundation
21 IS 8282 : Part 1 settlement in embankments
Code of practice - Code
for installation, of practiceand
maintenance (First Revision) of pore pressure measuring
observations
22 :IS1976 devices in concrete and masonry dams: Part 1 electrical
8282 : Part 2 Installation, maintenance and observations of pore pressure resistance
measuring typedevices
cell in concrete
: 1996 and masonry dams - Code of practice: Part 2 vibrating wire type cell
9. FLOOD MANAGEMENT, EROSION MANAGEMENT & DIVERSION WORK

1 IS 10084 : Part Criteria for design of diversion works: Part 1 coffer dams
2 1 : 10084
IS 1982 : Part Design of diversion works - Criteria: Part 2 diversion channel and open cut or conduit in the
3 2 : 2014 : 1994
IS 10751 body of dam
Planning and(First
designRevision)
of guide banks for alluvial rivers - Guidelines (First Revision)
4 IS 10788 : Part Code of practice for construction of diversion works: Part 1 cellular coffer dams
5 1 : 11130
IS 1984 : 1984 Criteria for structural design of barrages and weirs
6 IS 11150 : 1993 Construction of concrete barrages - Code of practice (First Revision)
7 IS 11532 : 1995 Construction and maintenance of river embankments (Levees) - Guidelines (First Revision)
8 IS 12094 : 2018 Planning and design of river embankments (Levees) - Guidelines (Second Revision)
9 IS 12892 : 1989 Safety of barrage and weir structures - Guidelines
10 IS 12926 : 1995 Construction and maintenance of guide banks in alluvial rivers - Guidelines (First Revision)
11 IS 13877 : 1993 Planning and design of fish pass - Guidelines
12 IS 13912 : 1993 Closure of diversion channel and open cut or conduit inthe body of the dam - Code of
13 IS 14262 : 1995 practice
Planning and design of revetment - Guidelines
14 IS 14592 : Part Planning and design of barrage powerhouses - Guidelines: Part 1 investigation, planning
15 1 : 14815
IS 1998 : 2000 and layout
Design flood for river diversion works - Guidelines
 BASIC SCHEDULE OF RATESWATER RESOURCES DEPARTMENT JAIPUR DISTRICT

16 IS 14955 : 2001 Guidelines for hydraulic model studies of barrages and weirs
17 IS 4410 : Part Glossary of terms relating to river valley projects: Part 12 diversion works (First Revision)
18 12 4410
IS : 1993: Part Gloss4ry of terms relating to river valley projects: Part 22 barrages and weirs
19 22 : 1994: Part 3
IS 4410 Glossary of terms relating to river valley projects: Part 3 river and river training (First
20 : 1988
IS 6966 : Part 1 Revision)
Hydraulic design of barrages and weirs - Guidelines: Part 1 alluvial reaches (First Revision)
21 : 1989
IS 7349 : 2012 Barrages and weirs - Operation and maintenance - Guidelines (Second Revision)
22 IS 7720 : 1991 Criteria for investigation, planning and layout for barrages and weirs (First Revision)
23 IS 8408 : 1994 Planning and design of groynes in alluvial river - Guidelines (First Revision)
24 IS 9461 : 1980 Guidelines for data required for design of temporary river diversion works
25 IS 9795 : Part 1 Guidelines for the choice of the type of diversion works: Part 1 coffer dams
: 1981

10. SPECIFICATION FOR DUCTILE IRON (DI) PIPES, FITTINGS, SPECIALS, PE & HDPE PIPES

1 IS 8329 Centrifugally cast (spun) ductile iron pressure pipes for water, gas and sewage -
2 IS 9523 specification
Ductile iron fittings for pressure pipes for water, gas and sewage - specification
3 IS 5382 Rubber sealing rings for gas mains, water mains and sewers
4 IS 638 Specification for Sheet Rubber Jointing and Rubber Insertion Jointing
5 IS 12288 Code of practice for use and laying of Ductile Iron pipes
6 IS 11606 Methods for sampling of Cast Iron pipes and fittings
7 IS 455 Portland slag cement
8 IS 12330 Sulphate resisting Portland cement
9 IS 6452 Specification for high alumina cement for structural use
10 IS 6909 Specification for supersulphated cement
11 IS 8112 43 grade ordinary portland cement
12 IS 1387 General requirements for supply of metallurgical materials
13 IS 1500 Methods for Brinell hardness test for metallic materials
14 IS 1608 Mechanical testing of metals - tensile testing
15 ISO 2531 Ductile iron pipes, fittings, accessories and their joints for water applications
16 ISO 4179 Ductile iron pipes and fittings for pressure and non-pressure pipelines -- Cement mortar
17 ISO 4633 lining seals -- Joint rings for water supply, drainage and sewerage pipelines --
Rubber
18 ISO 8179 Specification
Ductile for materials
iron pipes -- External zinc-based coating – Part 1: Metallic zinc with finishing layer
19 ISO 8179 Ductile iron pipes -- External zinc coating -- Part 2: Zinc rich paint with finishing layer
20 ISO 8180 Ductile iron pipelines -- Polyethylene sleeving for site application
21 ISO 10802 Ductile iron pipelines -- Hydrostatic testing after installation
22 ISO 10803 Design method for ductile iron pipes
23 ISO 16132 Ductile iron pipes and fittings -- Seal coats for cement mortar linings
24 AWWA M 41 Ductile - Iron pipe and fittings (guideline code for design, manufacturing, testing, jointing,
25 BS EN 545 laying iron
Ductile & installation etc.) accessories and their joints for water pipelines - Requirements
pipes, fittings,
26 IS 5822 and test methods
MS pipeline
27 IS 12288 DI pipeline
28 IS 127886:1989 Polyethylene pipe for irrigation-Laterals with amendments number 5
29 (Reaffirmed
IS 14151 (Part Irrigation equipment sprinkler pipes specifications IS 14151 (Part I)1999 Part I Polyethylene
30 I) 1999
IS 14151 (Part pipes
Irrigation equipment sprinkler pipes specifications Part II quick couples Polyethylene pipes
31 II) 1999
IS 4984 : 1995 High Density Polyethylene (HDPE) Pipes for Water Supply - Specifications
(Reaffirmed