DriscoPlex® MDPE & HDPE Molded Fittings
Molded Butt Tee
DriscoPlex® MDPE and HDPE Molded
Fittings are available to meet your needs in
compliance with ASTM D2513, D3261,
F2897 and AWWA C901 and C906 product
standards.
Made in the USA and produced from high
quality MDPE and HDPE material,
DriscoPlex® Fittings are manufactured from
PE 2708 and NSF-61/Annex G approved
PE 4710 resin as listed in PPI-TR4.
DriscoPlex® PE Fittings Advantages:
Durable Light Weight Chemical Resistant
Leak Tight Impact Resistant Life Cycle Cost
Excellent Flow Fusibility Toughness
Easy Install Corrosion Resistant Environmental
DriscoPlex® PE Fittings Material Physical Properties
Property Standard HDPE Typical Values MDPE Typical Values
Material Designation ASTM F714 PE4710 PE 2708
Cell Classification ASTM D3350 445574C (black) 234373E
Density [4] ASTM D1505 0.960 g/cc (black) 0.939 g/cc (Yellow)
Melt Index [4] ASTM D1238 0.08 g/10 min 0.18 g/10 min
Flexural Modulus [5] ASTM D790 >120,000 psi > 90,000 psi
Tensile Strength [5] ASTM D638 Type IV >3500 psi > 2800 psi
SCG (PENT) [7] ASTM F1473 >2000 hours > 2000 hours
HDB at 73°F (23°C) [4] ASTM D2837 1600 psi 1250 psi
Color; UV stabilizer [C] Black –
ASTM D3350
[E] – Yellow
This is not a product specification and does not guarantee or establish specific minimum or maximum values or
manufacturing tolerance for material or piping products to be supplied. Values obtained from tests of specimens taken
from piping product may vary from these typical values.
Bulletin PP 3.01 | February 2016 www.performancepipe.com © 2016 Chevron Phillips Chemical Company LP
Performance Pipe, a division of Chevron Phillips Chemical Company LP | 5085 W. Park Blvd | Suite 500 | Plano, TX 75093 | Phone: 800-527-0662 | Fax: 972-599-7329
Molded Butt Tee
Dimensions Package Package Box Part Number
Butt Tee DR/Wall
A x B x L (in) Quantity Weight (lbs) Quantity MDPE HDPE FM*
C
1/2" CTS 0.090" wall 1.69 x 2.83 x 5.65 10 0.05 100 1005165 - -
1" CTS 0.102" wall 1.72 x 2.94 x 5.88 10 0.15 100 1005206 - -
C
3/4" IPS DR 11 1.72 x 2.94 x 5.88 10 0.10 50 1005179 1007902 -
DR 9 0.20 - 1079219 -
1" IPS 1.72 x 3.06 x 6.12 10 50 C
DR 11 0.16 1005196 1007910 -
C
DR 10 0.45 1005218 - -
1 1/4" IPS 2.75 x 4.53 x 9.25 10 10
DR 11 0.45 1007917 -
C
1 1/2" IPS DR 11 3.02 x 4.62 x 9.24 10 0.60 10 1005229 1007923 -
DR 7 1.30 - 1078881 -
2.88 x 5.125 x F2
2" IPS DR 9 10 1.10 10 - 1007926 1003765
10.25 C F1
DR 11 0.95 1005246 1006426 1003777
DR 7 2.90 1096092 -
3.00 x 6.06 x 12.13
DR 9 2.45 1007929 -
3" IPS 4 4 C F1
DR 11 / 11.5 2.06 1005260 1007933 1003805
3.00 x 5.72 x 11.44
DR 17 2.15 - 1097154 -
DR 7 6.06 - 1096094 -
3.00 x 6.22 x 12.44 F2
DR 9 6.00 - 1007937 1003829
C F1
4" IPS DR 11 / 11.5 4 4.55 4 1005278 1006434 1003853
C
DR 13.5 3.00 x 6.75 x 13.50 4.16 1005283 - -
DR 17 4.00 - 1097152 -
DR 7 16.48 - 1096093 -
4.25 x 8.63 x 17.25 F2
DR 9 15.88 - - 1003881
C F1
6" IPS DR 11 / 11.5 1 10.35 1 1005291 1006442 1003900
C
DR 13.5 4.06 x 8.31 x 16.62 10.20 1005296 - -
DR 17 9.85 - 1007941 -
DR 7 37.00 - 1078932 -
F2
DR 9 35.60 - 1070200 1036859
6.00 x 12.09 x C F1
8" IPS DR 11 1 27.14 1 1005310 - 1003939
24.18 C
DR 13.5 26.70 1005316 - -
DR 17 25.84 - 1097363 -
This product flyer is intended for reference purposes. It should not be used in place of the advice from a licensed Professional Engineer.
Additional fitting sizes and DR available. Contact Performance Pipe.
Legend
C – CSA F1 – FM 150 F2 – FM 200
*FM Products only available in High Density Materials
Bulletin PP 3.01 | February 2016 www.performancepipe.com © 2016 Chevron Phillips Chemical Company LP
Performance Pipe, a division of Chevron Phillips Chemical Company LP | 5085 W. Park Blvd | Suite 500 | Plano, TX 75093 | Phone: 800-527-0662 | Fax: 972-599-7329
