XCMG mine car alarm fault information statistics

(a) Yellow alarm level 1: It does not affect the operation of the vehicle and will be inspected at the appropriate time.

(b) Red alarm level 0: prompts the driver to immediately use the service brake to stop the vehicle. (People need to get on the

Classifica quan
project
tion tity
Oil suction blockage alarm 3
Oil return blockage alarm 3
High pressure blockage alarm 3
Lift handle failure 1
Keep driving 1
Centralized lubrication system failure 1
Low steering accumulator pre-charge pressure alarm 3
Hydraulic Steering (accumulator) pressure low alarm 1
type3
Steering valve inlet pressure low alarm 1
Brake accumulator pre-charge pressure low alarm 3
High hydraulic oil temperature alarm 1
Loading brake pressure low alarm 1
Low brake pressure alarm 1
Brake cooling temperature low alarm 2
Low parking brake pressure alarm 1
Air filter clogging alarm 6
Low fuel level alarm 1
Engine yellow light alarm 1
Power type1 High water temperature alarm 1
Low oil pressure alarm 1
Low water level alarm in water tank 1
Engine red light alarm 1
Door detection 1
seat belt alarm 1
Front left suspension sensor failure 1
Front right suspension sensor failure 1
Rear left suspension sensor failure 1
Rear right suspension sensor failure 1
Electrical2
Weighing system failure 1
Battery (charging) voltage is low 1
Drive system yellow alarm 1
Electrical2

Car ladder failure 1

le. (People need to get on the car to check and troubleshoot)

grad
code
e
2 301-303
2 304-306
2 307-309
2 310
2 311
2 312
1 351-553
1 354
1 355
1 356-358
1 359
1 360
1 361
1 362-363
0 381
2 101-106
2 107
2 108
1 151
1 152
1 153
0 181
2 201
2 202
2 203
2 204
2 205
2 206
2 207
2 208
2 209
1 251
0 281
0 282
 XCMG mine car alarm fault information statistics
(a) Yellow alarm level 1: It does not affect the operation of the vehicle and will be inspected at the appropriate
time.

(b) Red alarm level 0: prompts the driver to immediately use the service brake to stop the vehicle. (People need
to get on the car to check and troubleshoot)

grad
Fault name code
e
Communication abnormality between ACU and DCU 601 0
Communication abnormality between ACU and ECU 602 0
Communication failure between ACU and ECM 603 0
Diesel engine over speed 604 0
Excitation controller parameter setting error 605 0
Left wheel motor coil temperature is high and unloaded 606 0
Left wheel motor bearing temperature is high and unloaded 607 0
Right wheel motor coil temperature is high and unloaded 608 0
Right wheel motor bearing temperature is high and unloaded 609 0
Excitation current overcurrent 610 0
Main generator overcurrent 611 0
Generator bearing temperature is high and unloaded 612 0
Generator stator winding temperature is high and unloaded 613 0
Generator bearing temperature is high 614 1
Generator stator winding temperature is high 615 1
Wrong direction handle 616 1
Truck speed alarm 617 1
The handle direction is different from the running direction 618 1
Service brake implementation 619 1
Parking brake not released 620 1
Left wheel motor coil temperature is high 621 1
Left wheel motor bearing temperature is high 622 1
Right wheel motor coil temperature is high 623 1
Right wheel motor bearing temperature is high 624 1
Left front wheel speed acquisition abnormality 625 1
Right front wheel speed acquisition abnormality 626 1
DC voltage saturation 627 1
spare 628 1
spare 629 1
spare 630 1
Module 1_A phase upper tube failure 631 0
Module 1_A phase down tube failure 632 0
Module 1_B phase upper tube failure 633 0
Module 1_B phase down tube failure 634 0
Module 1_C phase upper tube failure 635 0
Module 1_C phase down tube failure 636 0
Module 1_D phase upper tube failure 637 0
Module 1_D phase down tube failure 638 0
Module 2_A phase upper tube failure 639 0
Module 2_A phase down tube failure 640 0
Module 2_B phase upper tube failure 641 0
Module 2_B phase down tube failure 642 0
Module 2_C phase upper tube failure 643 0
 Module 2_C phase down tube failure 644 0
Module 2_D phase upper tube failure 645 0
Module 2_D phase down tube failure 646 0
Module 3_A phase upper tube failure 647 0
Module 3_A phase down tube failure 648 0
Module 3_B phase upper tube failure 649 0
Module 3_B phase down tube failure 650 0
Module 3_C phase upper tube failure 651 0
Module 3_C phase down tube failure 652 0
Module 3_D phase upper tube failure 653 0
Module 3_D phase upper tube failure 654 0
Module 4_A phase upper tube failure 655 0
Module 4_A phase down tube failure 656 0
Module 4_B phase upper tube failure 657 0
Module 4_B phase down tube failure 658 0
Module 4_C phase upper tube failure 659 0
Module 4_C phase down tube failure 660 0
Module 4_D phase upper tube failure 661 0
Module 4_D phase upper tube failure 662 0
Inverter 1_A phase overcurrent 663 0
Inverter 1_B phase overcurrent 664 0
Inverter 1_C phase overcurrent 665 0
Inverter 1 chopper overcurrent 666 0
Contrarian 2_A phase overcurrent 667 0
Inverter 2_B phase overcurrent 668 0
Inverter 2_C phase overcurrent 669 0
Inverter 2 chopper overcurrent 670 0
Module 1 overtemperature fault 671 0
Module 2 overtemperature fault 672 0
Module 3 overtemperature fault 673 0
Module 4 overtemperature fault 674 0
Module 1 receiving pulse fiber calibration failure 675 0
Module 2 receiving pulse fiber calibration failure 676 0
Module 3 receiving pulse fiber calibration failure 677 0
Module 4 receiving pulse fiber calibration failure 678 0
Module 1 pulse board program selection error 679 0
Module 2 pulse board program selection error 680 0
Module 3 pulse board program selection error 681 0
Module 4 pulse board program selection error 682 0
DC current overcurrent (hardware protection) 683 0
Ground protection (hardware protection) 684 0
Intermediate DC overvoltage (hardware protection) 685 0
pulse board1communication fail 686 0
pulse board2communication fail 687 0
Collection box communication failure 688 0
pulse board3communication fail 689 0
pulse board4communication fail 690 0
Collection box serious failure 691 0
spare 692 0
spare 693 0
Battery voltage is low 694 1
RX4 total fault fiber disconnection fault 695 0
 RX6 total fault fiber disconnection fault 696 0
RX10 total fault fiber disconnection fault 697 0
RX12 fault fiber disconnection fault 698 0
Intermediate DC overvoltage (detected by software) 699 0
DC current overcurrent (software detection) 700 0
Ground protection (software detection) 701 0
Inverter 1 chopper1Overcurrent 702 0
Inverter 1 chopper2Overcurrent 703 0
Intermediate DC undervoltage 704 0
Inverter 1 three-phase unbalanced 705 0
Inverter 1 lacks phase 706 0
Inverter 2 three-phase unbalanced 707 0
Inverter 2 lack of phase 708 0
Left wheel motor over speed 709 1
Right wheel motor over speed 710 1
Excitation contactor engagement 711 1
Excitation contactor stuck points 712 1
DCU fan engagement 713 1
DCU fan stuck points 714 1
Inverter 1 threshold feedback error 715 1
contrarian2Threshold feedback error 716 1
Ground protection threshold error 717 1
Intermediate overvoltage threshold error 718 1
Intermediate DC overcurrent threshold error 719 1
DSP1 life signal lost 720 0
DSP2 life signal lost 721 0
The internal temperature of the converter is too high 722 1
Rectifier module overheated 723 0
FPGA pulse selection control word 1 feedback error 724 0
FPGA pulse selection control word 2 feedback error 725 0
Chopper 1 threshold error 726 1
Chopper 2 threshold error 727 1
Inverter 2 chopper 1 overcurrent 728 0
Inverter 2 chopper 2 overcurrent 729 0
ACU life signal lost 730 0
ECU life signal lost 731 0
IOParameter feedback error 732 1
Traction inverter 1 blockade protection 733 1
Traction inverter 2 blockade protection 734 1
DC side ground detection 735 0
AC side ground detection 736 0
Intermediate DC 2 overcurrent 737 0
Left wheel motor level 1 overload 738 1
Left wheel motor level 2 overload 739 1
Right wheel motor level 1 overload 740 1
Right wheel motor level 2 overload 741 1
Abnormal wind pressure switch 742 1
Braking resistor chopper has no flow 743 1
The braking resistor is not connected and has no current. 744 1
Revolver speed acquisition abnormality 745 1
Right wheel speed acquisition abnormality 746 1
spare 747