Leaders in Life. Safety.

Technology

TRADE PRODUCT LIST

REVISION A

NEW ZEALAND Edition

Subject to change without notice

informationguide2019

www.notifier.co.nz 1 Trade Product List 2019

www.notifier.co.nz 2 Trade Product List 2019
 Table Of Contents

CONVENTIONAL FIRE ALARM CONTROL PANELS 3 INSTALLATION TOOLS 26

NOTIFICATION APPLIANCES 27
CFP-16 SERIES 3 HAZARDOUS AREA NOTIFICATION APPLIANCES 28
CFP-16 SERIES FIRE ALARM CONTROL PANEL 3 FIRE BELLS 29
CFP-16 PANEL ACCESSORIES 4
AGENT RELEASE EQUIPMENT 30
ADDRESSABLE FIRE ALARM CONTROL PANELS 5
AGENT RELEASE MODULE 30
ONYX AFP-3030 ADDRESSABLE FIRE ALARM CONTROL PANEL 5 AGENT RELEASE LOCAL CONTROL STATION (LCS) 30
ONYX AFP-3030 LOOP (SLC) MODULES 5 ILLUMINATED WARNING SIGNS 31
NOTI-FIRE-NET NCA-2- NETWORK CONTROL ANNUNCIATOR 7
AFP-3030 ANNUNCIATORS 7 ANCILLARIES 32
NOTI-FIRE NET NETWORKING MODULES 9
ONYX AFP-3030 ACCESSORIES 9 CONVENTIONAL MANUAL CALL POINTS 32
HAZARDOUS AREA MANUAL CALL POINTS 32
INTEGRATION 10 ADDRESSABLE MANUAL CALL POINTS 32
MAGNETIC DOOR HOLDERS 32
NOTIFIER ONYXWORKS™ WORKSTATION 10
ONYX FIRSTVISION™ 10 FLAME DETECTION 33
INTEGRATION - NOTI-FIRE-NET GATEWAYS 11
FLAME DETECTORS 33
CONVENTIONAL DETECTORS 12
GAS DETECTION 35
ADDRESSABLE DETECTORS 16
XCD GAS DETECTORS 35
ADDRESSABLE CLIP PROTOCOL DETECTORS 16
SWIFT 16 LINEAR HEAT DETECTION 36
FLASHSCAN PROTOCOL DETECTORS 16
DETECTOR ACCESSORIES 18 FIBRE OPTIC LINEAR HEAT DETECTION 36
REMOTE INDICATORS 19 GENERAL PURPOSE LINEAR HEAT DETECTION 36
ADDRESSABLE FIELD I/O MODULES 19 HARSH AREA LINEAR HEAT DETECTION 37
ADDRESSABLE FIELD INPUT & OUTPUT MULTI-MODULES 21
ADDRESSABLE LOOP POWERED AV 22 ASPIRATED SMOKE DETECTION 38

EMERGENCY WARNING SYSTEMS 23 VESDA DETECTORS 38

VESDA ACCESSORIES 40
I-2000 - EMERGENCY WARNING 23 FAAST ADDRESSABLE ASPIRATED SMOKE DETECTORS 41
FIRE FIGHTER TELEPHONE SYSTEM 23 ASPIRATED DETECTOR PIPE & FITTINGS 41
DIGITAL VOICE COMMAND 23
DA SERIES BUILDING OCCUPANT WARNING SYSTEM 24 OSID OPEN AREA DETECTION 42

EMERGENCY WARNING ANCILLARIES 25 POWER SUPPLIES & BATTERIES 43

CEILING SPEAKERS 25 NPS SERIES POWER SUPPLY 43

HORN SPEAKERS 25 BATTERIES 43
HONEYWELL AV SPECIAL APPLICATION SPEAKERS 26

www.notifier.co.nz 1 Trade Product List 2019

Table Of Contents

DETECTOR TEST & REMOVAL 44 INFORMATION 55

SOLO TEST KITS 44 IECEX HAZARDOUS AREA CLASSIFICATION 55

SOLO AEROSOLS 44 INGRESS PROTECTION (IP) 55
OTHER DETECTOR TEST & REMOVAL EQUIPMENT 45 NEMA ENCLOSURE TYPES TO IEC CLASSIFICATION 56
CABINET PAINT CODES 56
ENCLOSURES & MOUNTING CHASSIS 46 FLAME DETECTOR SELECTION GUIDE 57
FLAME DETECTOR APPLICATION GUIDE 57
MODULE ENCLOSURES 46 GAS DETECTOR APPLICATION GUIDE 58
CABINET SURROUNDS 46
MOUNTING CHASSIS & BRACKETS 47 TERMS & CONDITIONS OF SALE 59

INSTALLATION CABLE 48 INDEX 62

I.S BARRIERS & SURGE SUPPRESSION 49

INTRINSICALLY SAFE BARRIERS & ISOLATORS 49

SURGE SUPPRESSION MODULES 49

SPARE PARTS 50

GENERIC 50
POWER SUPPLIES 50
NFS 2-8 SERIES FACP 50
IFS-2600 SERIES FACP 50
CFP-16 SERIES FACP 50
PRINTER EQUIPMENT 50
AM-1010/AFP-2020 SERIES 50
AFP-3030 SERIES PANEL 51
AFP-2800 SERIES FACP 51
SOLO TEST EQUIPMENT 52
I-2000 EWIS 52
VESDA 53
OSID 54

www.notifier.co.nz 2 Trade Product List 2019

 Conventional Fire Alarm Control Panels

CFP - 16 SERIES FIRE ALARM CONTROL PANEL

With usability as a key focus for development

Part # Description
and utilizing industry leading manufacturing and
testing practices; the CFP-16 will provide an easy CFP-16/650-8Z-PS5NZ 8 zones fitted with NPS-5 in CAB650

to use and powerful detection and control system CFP-16/900-8Z-PS5NZ 8 zones fitted with NPS-5 in CAB900
for all conventional detection applications.
CFP-16/650-8Z-PS11NZ 8 zones fitted with NPS-11 in CAB650

The standard panel is equipped with 8 zones but CFP-16/900-8Z-PS11NZ 8 zones fitted with NPS-11 in CAB900
may be extended to 16 Zones by the addition of
an 8 Zone expansion module.

The CFP-16 is extremely flexible and can be Zone Index Kits

programmed to meet the demands of a wide
variety of building types. Part # Description

• Simple to install FSKIT650NZ NZ Acrylic (FS) kit, includes Annunciator Plates CAB650

• Expandable to 16 x conventional FSKIT900NZ NZ Acrylic (FS) kit, includes Annunciator Plates CAB900
zones
• 24 character programmable zone descriptor RSMSK650 CAB650 Rear Service Mimic Surrounod Kit

• Compatible with System Sensor devices RSMSK900 CAB650 Rear Service Mimic Surrounod Kit
• Space for up to 33AH batteries
• IP30 rated for CAB650 / CAB 900

Cabinet Dimensions: Accessories

- CAB650 - 650mm H x 450mm W x 190mm D
Part # Description
- CAB900 - 900mm H x 450mm W x 190mm D
ZEM-8 8 Zone expansion module to suit CFP-16
FPA Equipment Listing #: NI/102
ACM-8RA Relay module to provide up to 8 C/NO/NC relay contacts

ZLKT16 Annunciator name plate for zone & custom labelling

Remote LED mimic annunciator for up to 8 zones with status

ACM-ZM8
LED’s

NOTE: Contact your Notifier systems consultant for pricing of alternate configurations

CFP - 16 SERIES FIRE AGENT RELEASE PANEL

Incorporating all the features of the CFP-16

Part # Description
FACP and the Notifier agent release module the 8 zones fitted with NPS-5, 1 x Agent Release zone in CAB650
CFP-16/650F-LCS1
agent release control panels provide 8 zones of with LCS fitted to outer door

detection with 1 zone of agent release. 8 zones fitted with NPS-5, 1 x Agent Release zone in CAB900
CFP-16/900F-LCS2
with LCS fitted to outer door
• CAB650 and CAB900 versions available 8 zones fitted with NPS-5, 1 x Agent Release zone in CAB650
CFP-16/650F-LCS3
• Versions available with LCS fitted to with LCS fitted to outer door and DA30 OWS
outer door. 8 zones fitted with NPS-5, 1 x Agent Release zone in CAB900
• Space for up to 33AH batteries CFP-16/900F-LCS4
with LCS fitted to outer door and DA30 OWS
• IP30 rated for CAB650 / CAB 900
Zone Index Kits
Cabinet Dimensions:
- CAB650 – 650mm H x 450mm W x 190mm D
Part # Description
- CAB900 – 900mm H x 450mm W x 190mm D FSKIT650NZ NZ Acrylic (FS) kit, include Annunciator Plates CAB650
FSKIT900NZ NZ Acrylic (FS) kit, include Annunciator Plates CAB900
FPA Equipment Listing #: NI/102 RSMSK650 CAB650 Rear Service Mimic Surround Kit
RSMSK900 CAB900 Rear Service Mimic Surround Kit

www.notifier.co.nz 3 Trade Product List 2019

Conventional Fire Alarm Control Panels

CFP-16 PANEL ACCESSORIES

ACM-8RA Relay Expansion Module Part # Description

ACM-8RA Relay module to provide up to 8 C/NO/NC relay contacts
Provides 8 programmable relay contacts.
• Fits into standard CHS-xL slot.
• 1A @ 24VDC contacts
• Expandable up to 32 modules
• Compatible with CFP-16

FPA Equipment Listing#: NI/665

CFP-16 LED Mimic Modules Part # Description

Provides 8/16 zone remote alarm indication ACM-ZM8 Remote LED mimic annunciator for up to 8 zones with status LED’s

AEM-ZM8 Remote LED mimic expansion annunciator for an additional 8 zones

• Compatible with standard annunciator
mounting enclosures
• Red high-intensity LED’s See Page 46 for Annunciator mounting enclosures

FPA Equipment Listing#:

CFP-16 SGD and interface Part # Description

The SGD (signal generating device) provides the SGDIF16 SGD interface to suit CFP- 16NZ

interface to the NZ alarm monitoring services SFDMK16 SGD Inner Door Mounting KitI

This mounts in either in a slot on the CHS-3L or can be

mounted on a standard annunciator slot using the
SGD Inner Door Mounting Kit.

FPA Equipment Listing #: NI/501

Strobe/Sounder Interface Part # Description

• 5A reversible output for use with dual strobes IFS-993F Monitored Strobe/Sounder Interface
• Comes with subplate to fit into standard CHS-xL slot

FPA Equipment Listing#: NI/667

Slim Remote Zone Index Mimic Part # Description

AEM-ZM8 Remote LED mimic expansion annunciator for an additional 8 zones
The slim LED mimic panels provide a convenient
means of remotely placing an LED index away from MIM425 with ACM-ZM 8 Zones, ONYX Black
the main fire alarm control panel. ZMS/425RF-8ZI
(Max 24 zones or 48 zones in 2 rows)
The mimics connect to the panel’s serial ACM- 485
communications line via a four core cable (two data ZMS/900RF-8ZI MIM900 with ACM-ZM 8 Zones, ONYX Black (Max 72 zones)
and two power connections).

The ACM-ZM Zone mimic interface module is fitted Cabinet Dimensions:

in the mimic cabinet and interfaces to the Silence - ZMS/425 – 425mm H x 450mm W x 51mm D
Alarms and Evacuation Bulgin keys. - ZMS/900 – 900mm H x 450mm W x 51mm D

www.notifier.co.nz 4 Trade Product List 2019

 Addressable Fire Alarm Control Panels

ONYX AFP-3030 ADDRESSABLE FIRE ALARM CONTROL PANEL

Onyx AFP-3030 Part # Description

AFP-3030 1-loop fitted with NPS-5 in CAB650 with Display and
The AFP-3030 is an intelligent Fire Alarm Control Panel AFP-3030NZ/ D650R1L5
Rear Service
(FACP) with a flexible and scaleable architecture which
AFP-3030 1-loop fitted with NPS-5 in CAB650 with Display and
makes it suitable for virtually any application including AFP-3030NZ/ D650F1L5
Front Service
large scale networked facilities. Fire emergency detection
and evacuation are extremely critical to life safety, and AFP-3030 1-loop fitted with NPS-5 in CAB900 with Display and
AFP-3030NZ/D900R1L5
Rear Service
the AFP-3030 is ideally suited for these applications
AFP-3030 1-loop fitted with NPS-5 in CAB900 with Display and
• One to ten addressable loops AFP-3030NZ/ D900F1L5
Front Service
• Up to 159 detectors and 159 modules per SLC, 318
AFP-3030 1-loop fitted with NPS-5 in 18U with Display, No
devices per loop / 3,180 per FACP (or network node) AFP-3030NZ/ D18Ux1L5
Service
• Networkable up to 200 nodes
AFP-3030 1-loop fitted with NPS-5 in 28U with Display, No
• Field programmable with QWERTY keypad AFP-3030NZ/ D28Ux1L5
Service
• Support for AS1668.1 compliant smoke control
with SCS Series smoke control system
• VeriFire Tools programming, diagnostic and Agent Release Panels
reporting tools Part # Description
AFP- 3030NZ/650F1L5GL AFP-3030NZ/650F-1L-PS5-GL with ARM & display
Cabinet Dimensions:
AFP- 3030NZ/900F1L5GL AFP-3030NZ/900F-1L-PS5-GL with ARM & display
- CAB650 – 650mm H x 450mm W x 190mm D
- CAB900 – 900mm H x 450mm W x 190mm D
Zone Index Kits
FPA Equipment Listing #: HW/104 Part # Description
FSKIT650NZ NZ Acrylic (FS) kit, includes Annunciator Plates CAB650
FSKIT900NZ NZ Acrylic (FS) kit, includes Annunciator Plates CAB900
RSMSK650 CAB650 Rear Service Mimic Surround Kit

RSMSK900 CAB900 Rear Service Mimic Surround Kit

Accessories

Part # Description
ACM-ZM8 Remote LED mimic annunciator for up to 8 zones with status LED’s
ACM-8RA Relay module to provide up to 8 C/NO/NC relay contacts
ZLKT16 Annunciator name plate for zone & custom labelling

NOTE: Contact your Notifier systems consultant for pricing of alternate configurations

ONYX AFP-3030 LOOP (SLC) MODULES

AFP-3030 Loop (SLC) Modules Part # Description

• Installs into standard CHS-xL chassis LCM-320 Loop Control Module Used as loops 1, 3, 5, 7 or 9
• Supports CLIP and FlashScan protocols LEM-320 Loop Expander Module Used as loops 2, 4, 6, 8 or 10
(panel dependant)
• Up to 400mA driving current

FPA Equipment Listing #: NI/671, NI/672

ACM-8RA Relay Expansion Module

Part # Description
Provides 8 programmable relay contacts. ACM-8RA Relay module to provide up to 8 C/NO/NC relay contacts

• Fits into standard CHS-xL slot.

• 1A @ 24VDC contacts
• Expandable up to 32 modules
• Compatible with CFP-16

FPA Equipment Listing#: NI/665

www.notifier.co.nz 5 Trade Product List 2019

Addressable Fire Alarm Control Panels

AFP- 3030 LED Mimic Modules Part # Description

Provides 8/16 zone remote alarm indication ACM-ZM8 Remote LED mimic annunciator for up to 8 zones with status LED’s

AEM-ZM8 Remote LED mimic expansion annunciator for an additional 8 zones

• Compatible with standard annunciator
mounting enclosures
• Red high-intensity LED’s See Page 46 for Annunciator mounting enclosures

FPA Equipment Listing#:

AFP- 3030 SGD and interface

Part # Description
The SGD (signal generating device) provides the
SGDIF16 SGD interface to suit AFP- 3030
interface to the NZ alarm monitoring services
SFDMK16 SGD Inner Door Mounting KitI
This mounts in either in a slot on the CHS-3L or can be
mounted on a standard annunciator slot using the
SGD Inner Door Mounting Kit.

FPA Equipment Listing #: NI/501

Strobe/Sounder Interface
Part # Description
• 5A reversible output for use with dual strobes IFS-993F Monitored Strobe/Sounder Interface
• Comes with subplate to fit into standard CHS-xL slot

FPA Equipment Listing#: NI/667

Slim Remote Zone Index Mimic Part # Description

Remote LED mimic expansion annunciator for an additional 8
The slim LED mimic panels provide a convenient AEM-ZM8
zones
means of remotely placing an LED index away from
MIM425 with ACM-ZM 8 Zones, ONYX Black
the main fire alarm control panel. ZMS/425RF-8ZI
(Max 24 zones or 48 zones in 2 rows)
The mimics connect to the panel’s serial ACM- 485
communications line via a four core cable (two data ZMS/900RF-8ZI MIM900 with ACM-ZM 8 Zones, ONYX Black (Max 72 zones)
and two power connections).

The ACM-ZM Zone mimic interface module is fitted Cabinet Dimensions:

in the mimic cabinet and interfaces to the Silence - ZMS/425 – 425mm H x 450mm W x 51mm D
Alarms and Evacuation Bulgin keys. - ZMS/900 – 900mm H x 450mm W x 51mm D

AFP-3030 Programming cable Part # Description

USB3 USB lead 3m, to suit AFP-3030/ NCA-2
Up-load/ download cable

www.notifier.co.nz 6 Trade Product List 2019

 Addressable Fire Alarm Control Panels

NOTI-FIRE-NET NCA-2 - NETWORK CONTROL ANNUNCIATOR

The NOTIFIER NCA-2 is a second-generation Part # Description

NCA-2NZ - Network Control Annunciator to suit NFN, CPU Assembly
Network Control Annunciator for the NOTI•FIRE•NET™ NCA-2AUPLUS
inc mounting brackets
network, compatible for use with ONYX® AFP-3030 fire
alarm control panels, as well as first-generation NCA
Network Control Annunciators.

The NCA-2 provides system control and display capabilities

for all, or for selected network nodes. When connected to
one or more networked panels the NCA-2 provides network
control and status/history display capabilities. It may also be
configured as the Primary Display for displayless nodes on
the network.
• Enhanced-format 640-character LCD display with
backlighting.
• Easy to use control interface consisting of “soft” keys used
to navigate screen menus, “hard” keys with fixed control
functions and a full QWERTY keypad.
• Full supervision of all inputs and network
integrity.
• Requires 24V DC, and a network connection
• Required as master control node for mixed
AFP-3030 / AFP-2800 networks

AFP-3030 ANNUNCIATORS

LCD2-80 remote mimic display

Part # Description
• Provides 80 character mimic function LCD2-80 80 character LCD remote mimic panel
• Displays all alarm, fault and isolate conditions
• Compatible with standard mounting enclosures See Page 46 for Annunciator mounting enclosures

FPA Equipment Listing #: NI/631

SCS-8 Smoke Control Station Part # Description

SCE-8A Smoke Control Annunciator (expander) 8 x switch groups
Provides 8 banks of switches and indications
suitable for AS1668 fan and damper controls SCS-8A Smoke Control Annunciator (control) 8 x switch groups
SCE-8LA Smoke Control Module (expander) 8 x switch groups
• Incorporates lamp test and A/C reset buttons SCS-8LA Smoke Control Module (control) 8 x switch groups

FPA Equipment Listing #: NI/630 See Page 46 for Annunciator mounting enclosures

www.notifier.co.nz 7 Trade Product List 2019

Addressable Fire Alarm Control Panels

ACM-24AT Annunciator Control Module Part # Description

ACM-24AT Control Annunciator 24 buttons, 48 LED indications
• Ideal for zone isolates and test solenoids
• 24 color-programmable (red/green/ AEM-24AT Expansion Annunciator 24 buttons, 48 LED indications

yellow) Active and 24 yellow Fault LEDs,

24 momentary touch-pad switches
See Page 46 for Annunciator mounting enclosures
• System Fault LED
• On- Line/Power LED
• Local piezo sounder with a silence switch for
audible indication of alarm and fault conditions

ACM-48A Annunciator Control Module Part # Description

ACM-48AT Annunciator (Control) 48 x LED indications
• Ideal for zone alarm indications AEM-48AT Annunciator (expander) 48 x LED indications
• 48 color-programmable (red/green/yellow)
Active LEDs
• System Fault LED See Page 46 for Annunciator mounting enclosures

• On-Line/Power LED
• Local piezo sounder with a Silence switch
for audible indication of alarm and trouble
conditions
• Slide-out zone text label

LDM-32 Lamp & Relay Driver Module Part # Description

LDM-32 Lamp driver module (control), to suit AFP-3030
Provides 32 x 0V sink outputs to drive LEDs. Ideally suited
to graphical mimics. LDM-R32 Lamp driver module (expander), to suit AFP-3030

• The optional relay driver module provides 32 x

common, normally open contacts. FPA Equipment Listing #: NI/634, NI635
• Fits into CHS-xL chassis

www.notifier.co.nz 8 Trade Product List 2019

 Integration

NOTI-FIRE NET NETWORKING MODULES

Noti·Fire·Net™ Network Modules Part # Description

NCM-W Noti·Fire·Net control module – Wire
• Supports network of up to 100 nodes
• Wire, multi and single mode fibre NCM-F Noti·Fire·Net control module – MMOF

options
• 312.5K baud transmission rate
• Dual port for network redundancy
• Mounts on PSI or fits into CHS-xL chassis

NOTE: Not compatible with High Speed

Noti·Fire·Net™

Noti·Fire·Net™ Repeater Modules Part # Description

RPT-WF Noti·Fire·Net Wire to MMOF repeater
• Regenerates Noti·Fire·Net signals for
extremely long cable/fibre runs RPT-W Noti·Fire·Net Wire to Wire repeater

• Mounts on PSI or fits into CHS-xL chassis

NOTE: Use HS-NCM-x for High Speed

Noti·Fire·Net™

High Speed Noti·Fire·Net™ Network Part # Description

Modules HS-NCM-W High Speed Noti·Fire·Net Module – Wire

• Supports network of up to 200 nodes HS-NCM-MF High Speed Noti·Fire·Net Module – MMOF
• Wire, multi and single mode fibre options inc HS-NCM-SF High Speed Noti·Fire·Net Module – SMOF
hybrid cards HS-NCM-WMF High Speed Noti·Fire·Net Module – Wire / MMOF
• Up to 100mb baud transmission rate
HS-NCM-WSF High Speed Noti·Fire·Net Module – Wire / SMOF
• 1 x HS-NCM can support 2 nodes
HS-NCM-MFSF High Speed Noti·Fire·Net Module – MMOF / SMOF
• Can be used as a repeater
• Mounts on PSI or fits into CHS-xL chassis

www.notifier.co.nz 9 Trade Product List 2019

Integration

NOTIFIER ONYXWORKS™ WORKSTATION

ONYXWorks™
Powerful, versatile platform for life safety management

ONYXWorks is the next generation in life safety management for centralized control and monitoring of the fire alarm
system. The intuitive, graphical display allows personnel to rapidly pinpoint, investigate, and respond to alarm events
with minimal operator training. Versatile enough for single-site, multi-site and even worldwide applications, the
ONYXWorks graphical workstation allows end-users to manage their NOTIFIER life safety system over a proprietary
network or Ethernet.

Through its intelligent gateway architecture, ONYXWorks can easily meet the needs of expanding systems. ONYXWorks is also an
ideal retrofit solution. Additionally, ONYXWorks provides mass notification capabilities through IP-based voice paging and LED sign
integration.

• Contemporary intuitive interface

• Simple, non proprietary configuration.
• Monitor and control up to 200 fire networks
• Mass notification paging functions
• Email alerting functions
• Operates on Microsoft Windows 10 (64 bit,
Enterprise)

Workstation

Description
OnyxWorks™ Workstation & map development

Software Licensing

Part # Description
OnyxWorks™ Workstation Basic Licence, includes email and Netlogic
OW-LIC-BASIC
(requires map development)
OW-LIC-NOTIFY-IP Workstation licence upgrade

OW4-LIC-UG Upgrade licence OnyxWorks™ from previous to v4

PC-Based Noti·Fire·Net Gateways

Part # Description
NFN-GW-PC-W PC based NFN gateway, Wire
NFN-GW-PC-F PC based NFN gateway, MMOF

ONYX FIRSTVISION™

ONYX FirstVision™ is a revolutionary way

Description
finding navigational tool for fire fighters and
other emergency responders. Onyx FirstVision™ 22” way finding tool including map development
ONYX FirstVision™ utilizes a 22” touch
screen interface to graphically display critical
information on the origin and spread of a fire;
allowing fire fighters to quickly locate and
extinguish the fire.

• Intuitive interface designed for fire fighters

• Self unlocking metal enclosure
• Displays information on multiple fire
networks
• Presents hazmat, hydrant and other related
information

www.notifier.co.nz 10 Trade Product List 2019

 Integration

INTEGRATION - NOTI-FIRE-NET GATEWAYS

BacNet Gateway Part # Description

Provides a BacNet interface from a Noti·Fire·Net BACNET-GW Bacnet gateway- Interface between Noti-fire-Net and BACnet protocol

to BMS system etc.

• Max 15,000 Bacnet objects on 14 nodes

• Uses BacNet over IP
• Requires network control module

ModBus Gateway Part # Description

Provides a ModBus interface from a Noti·Fire·Net MODBUS-GW Modbus/TCP Gateway

to BMS system etc.

• Monitors up to 4 nodes
• Uses ModBus over IP
• Requires network control module

Embedded Noti·Fire·Net Gateway Part # Description

NFN gateway used to provide an interface to NFN-GW-AU-EM-3 Embedded Noti-Fire-Net gateway
OnyxWorks™ Workstation or ONYX FirstVision™

• Monitor and control of all nodes on the

Noti·Fire·Net network
• Utilizes TCP/IP
• Requires network control module

PC based NotiFireNet Gateway Part # Description

NFN gateway used to provide an interface to NFN-GW-PC-F NFN-GW-PC-F -PC based NFN gateway
OnyxWorks™ Workstation or ONYX FirstVision™
NFN-GW-PC-W PC based NFN gateway

• Monitor and control of all nodes on the

Noti·Fire·Net network
• Utilizes TCP/IP
• Requires network control module

NWS-3 Web Server Part # Description

NWS-3 Notifier Web Server
Provides a web server functionality to remotely
monitor the status of all devices on a Noti·Fire·Net from
any computer using an internet browser.

• Utilizes TCP/IP
• Requires network control module

VESDAnet Gateway
Part # Description
The VESDA Gateway provides a communication VESDA-HLI-GW VesdaNet gateway
link between the NOTI•FIRE•NET™ network
and the Xtralis™ VESDAnet network.

• Utilizes TCP/IP
• Requires network control module
• Supports up to 100 detectors

www.notifier.co.nz 11 Trade Product List 2019

Conventional Detectors

CONVENTIONAL DETECTORS

Low Profile 4-wire Smoke Alarms Part # Description

• AS3786 2014 A1 approved 2012/24AUSI 2012/24AUSI Photoelectric with 9V battery back-up

• Pure white colour 2012J Photoelectric externally powered

• Built in sounder
• N/O and N/C Alarm contacts
• Interconnect up to 24 units

2151BAUS – Low Profile Photo Detector Part # Description

• Low profile design Conventional photo optical smoke detector, 7%/m obscuration, uses B401AUS
2151BAUS
• Chamber design resists entry of dust Base - off white

• Flashing LED with maintenance alert

• Dual LED’s for 360° visibility
• Field cleanable with easily removed cover
• 12/24VDC operation
• 7%/m obscuration
FPA Equipment Listing#: NI/308

5151 Series Thermal Detectors Part # Description

• Provides rate of rise &/or fixed point operation Conventional thermal detector, rate of rise, 63deg, system sensor, requires
5151RAUS
• Available in low temperature (63°C) and high B401AUS - off white, Type A

temperature (90°C) Conventional thermal detector, fixed temp 63deg, system sensor, requires
5151AUS
• Uses universal B401 plug in base B401AUS - off white, Type B
• Magnetic test feature Conventional thermal detector, rate of rise, 90deg, system sensor, requires
5151HRAUS
• Dual LED’s for 360° visibility B401AUS - off white, Type C
• 12/24VDC operation Conventional thermal detector, fixed temp 90deg, system sensor, requires
5151HAUS
B401AUS - off white, Type D
FPA Equipment Listing#: NI/221, NI/219, NI/222, NI/220

B401AUS Universal Conventional Detector Base Part # Description

• Universal for all plug-in conventional Universal conventional detector base (for System Sensor Series 100
B401AUS
detectors conventional detectors) - off white

• Shorting-spring to ensure continuity

when testing circuit Accessories
• Colour coded terminals Description
Part #
• Tamper proof lock
Surface mount box to suit detector base B501AUS/B401AUS
• Multiple hole centres SMK-400
- off white
WB-1AP-IV Wet base shroud for detector base
WB-1AP-IV
- off white

50xx Series Conventional Fixed Temperature Heat Part # Description

Detector
5057NZ 5057 Conventional fixed heat detector Blue (58°C)
5076NZ 5076 Conventional fixed heat detector Yellow (77°C)
• Available in two temperature ranges (Blue: 58°C and
Yellow: 77°C). 5057WPNZ 5057WP Waterproof Conventional fixed heat detector Blue (58°C)
• The heat detectors come in two variants; standard 5076WPNZ 5076WP Waterproof Conventional fixed heat detector Yellow (77°C)
version for normal usage and a weatherproof version
for use outdoors or in areas where moisture or dust is
present.
• The Notifier bi-metallic heat sensor is a highly reliable
detector with an aesthetically pleasing, compact, low
profile design.

FPA Equipment Listing #: NI/223, 224, 225, 226

www.notifier.co.nz 12 Trade Product List 2019

 Conventional Detectors

Photo-Electric Duct Detectors Part # Description

• Air velocity rating from 0.5 m/s to 20.32m/s D2-AUS Conventional 2-wire duct detector

• Versatile mounting option.

D4120W 4-Wire watertight duct detector (24VDC, 24VAC, 120VAC)
• Includes replaceable plug-in sensor head
• Backward compatible with Innovair models D4120 Photo Duct detector 4-wire (24VDC, 24VCA, 120VAC)
• Multi-voltage (stand-alone) options Wet Base shroud off-white, suitable for analogue andconventional detectors
WB-1AP-IV
available 200 series

NOTE: Requires sampling tube Accessories

Part # Description
FPA Equipment Listing #: NI/326, 328, 327
DST-1.5 Sampling tube to suit duct 0.3m to 0.6m
DST-3 Sampling tube to suit duct 0.5m to 1.2m
DST-5 Sampling tube to suit duct 1.2m to 2.4m
DST-10 Sampling tube to suit duct 2.4m to 3.7m
ETX Duct detector exhaust tube

Conventional Reflector Type Beam Detectors Part # Description

• Single-ended reflective design BEAM1224 Conventional beam detector

• 10-100m range >70m requires BEAMMK BEAM1224S Beam detector with built in test station
• 4-wire 12/24VDC operation
• Ceiling or wall mount Accessories
• In-built alignment tool Part # Description
• Automatic gain control
BEAMSMK Surface Mount Kit for BEAM 1224, for flat surfaces only
• Remote test station available
BEAMLRK BEAMSMK Surface mount kit Long range kit (70-100m)
• BEAM1224S includes built-in test station
Multi mount kit - For use when mounting beam detector on ceiling or on an
FPA Equipment Listing #: NI/311, 312 BEAMMK
angle.
RTS451KEY Remote test station with key lock to reset beam detector

Type E Thermal Probes Part # Description

• Provides fixed point operation E60 Type E Thermal Probe set @ 60 °deg

• High Temperature setting E70 Type E Thermal Probe set @ 70 °deg

• Common & Normally Open contacts E80 Type E Thermal Probe set @ 80 °deg
• 316 Stainless Steel E90 Type E Thermal Probe set @ 90 °deg
• Not certified for NZ4512, can be used for engineered
E100 Type E Thermal Probe set @ 100 °deg
solutions++
E110 Type E Thermal Probe set @ 110 °deg
E120 Type E Thermal Probe set @ 120 °deg
E150 Type E Thermal Probe set @ 150 °deg
E180 Type E Thermal Probe set @ 180 °deg
E200 Type E Thermal Probe set @ 200 °deg

E240 Type E Thermal Probe set @ 240 °deg

www.notifier.co.nz 13 Trade Product List 2019

Ancillaries

CONVENTIONAL MANUAL CALL POINTS

Part # Description
Conventional Indoor MCP
MCPCNZ NZ conventional MCP Indoor Red, flexible element, with clear flap
This MCP is highly reliable with an aesthetically pleasing,
compact, low-profile design.
Accessories
• Flexibal non- frangible element
Part # Description
FPA Equipment Listing#: NI/601 NZMCPOS Polycarbonate MCP operation sign
NZFE1612 Flexible MCP element with Notifier Logo
PS200FLAP Replacement Clear flap cover for MCP
SC070 Spare test key (pk10)
PS059 Breakable seal for hinged cover (pk5)

Conventional Outdoor MCP NZTB017 Surface mount bezel and adaptable plate for NZ back box

SG-1x10 Glass replacement element for MCP (Pack of 10)

This MCP is highly reliable with an aesthetically pleasing, Indoor Protective cover Stopper II® with Horn & Clear Spacer, Fire Label / red
STI-1130
compact, low-profile design. horn/clear space

• Flexibal non- frangible element

• IP67 Part # Description
MCPCWPNZ NZ conventional MCP Outdoor Red, flexible element, with clear flap
FPA Equipment Listing#: NI/602

Conventional Indoor Manual Call Points Part # Description

• Normally Open and Normally Closed MCP1A-R Red MCP, indoor, surface mount, “House + Flame”, back box included

operation MCP3A-R Red MCP resettable indoor, surface mount

• Transparent cover available. MCP3A-W White MCP, indoor, surface mount “Emergency Alarm”
(Standard on Yellow MCP) MCP3A-Y Yellow MCP, indoor, surface mount, “Extinguishant Release”
• Multiple colour options for variety of
MCP3A-G Green MCP, indoor, surface mount, “Door Release”
functions
MCP3A-B Blue MCP, indoor, surface mount, no label
• Flexible (non-glass) element available
(Standard on Red resettable MCP)
Accessories

Part # Description
SG-1x10 Spare MCP glass (pk 10) common to all MCP’s
Clear replacement flap to cover MCP from accidental
PS200FLAP
breakage - curved shape
PS210 Flexible MCP element to suit KAC MCP’s
SC070 Spare test key (pk 10) SC070

WCP3A Conventional Outdoor Manual Call Points

Part # Description
• Outdoor (IP67) rating WCP3A-R Red surface mount MCP, “House + Flame”
• Normally Open and Normally Closed operation WCP3A-W White surface mount MCP, “Emergency alarm”
• Transparent cover available. WCP3A-Y Yellow surface mount MCP with clear cover, “Extinguishant Release”
(Standard on Yellow MCP)
WCP3A-G Green surface mount MCP, “Door Release”
• Multiple colour options for variety of functions
WCP3A-B Blue surface mount MCP, no label
• Flexible (non-glass) element available

Accessories

Part # Description
SG-1x10 Spare MCP glass (pk 10)
Clear replacement flap to cover MCP from accidental
PS200FLAP
breakage - curved shape
PS210 Flexible MCP element
SC070 Spare test key (pk 10)

www.notifier.co.nz 14 Trade Product List 2019

 Ancillaries

Double Pole Manual Call Points Part # Description

• Indoor & Outdoor (IP67) rating White Double pole indoor call point for Emergency door release, with flexible
MCP4A-WSF
• Transparent cover available. element

• Multiple colour options for variety of functions Green Double pole indoor call point for Emergency door release, with flexible
MCP4A-GSF
• With Glass or Flexible (non-glass) element element
available Green Double pole indoor call point for Emergency door release, with glass
MCP4A-GSG
element

WCP4A-GSG Green Double pole outdoor call point IP67, with glass element

WCP4A-RSG Red Double pole outdoor call point IP67, with glass elemen

CONVENTIONAL HUSH MODULE

NZ Conventional Hush Module

Part # Description
Notifier’s Conventional Global Hush Module is designed to HUSHCM NZ Conventional Hush Module
be used as a component part of a managed smoke facility
System (MSFM) on the CFP-16 conventional fire alarm
control panel.

• Provides a cost effective solution for installations in

residential premises
• Simple installation and mounting
• Operating instructions screened on fascia of the unit (no
additional label required)
• Flexible panel programming for MSFM operation

www.notifier.co.nz 15 Trade Product List 2019

 Addressable Detectors

ADDRESSABLE CLIP PROTOCOL DETECTORS

SDX-851 Intelligent Photo Sensor Part # Description

• CLIP protocol SDX-851AUS CLIP Photo-optical Smoke Sensor - off white
• Flat chamber design to reduce false alarms
• Adjustable from 1.64% to 7.71%/m
obscuration

FPA Equipment Listing#: NI/321

FDX-851(R) Intelligent Thermal Sensor Part # Description

• CLIP protocol FDX-851AUS CLIP fixed temperature thermal sensor - off white
• Fixed Temp or Rate-of-Rise models FDX-851RAUS CLIP rate of rise thermal sensor - off white
available
• Adjustable from 58°C to 88°C

FPA Equipment Listing#: NI/217, 218

IDX-751 – Intrinsically Safe Addressable Part # Description

Photoelectric Detector
IDX-1AE Intrinsically safe addressable photoelectric detector - off white
• CLIP protocol
• Uses universal B501 plug in base
• Use with KFD0-CS-Ex1.54-Y2 - P+F 1-channnel Accessories
isolated barrier
Part # Description
Certified to IEC:
- Ex ia-IIB T5 Ga (-20oC ≤ Ta ≤ +40oC) IMX-1E Intrinsically safe translator module.

- Ex ia-IIB T4 Ga (-20oC ≤ Ta ≤ +60oC)

- Zones 0, 1 and 2 See page 49 for isolators

FPA Equipment Listing#: NI/323

ADDRESSABLE FLASHSCAN PROTOCOL DETECTORS

FSP-851 Intelligent Photo Sensor Part # Description

• FlashScan protocol FSP-851AUS FlashScan Photo-optical Smoke Sensor - off white

• Dual Bi-colour LED indication FSP-851AUS/BCK FlashScan Photo-optical Smoke Sensor - black
• Flat chamber design to reduce false alarms
• Adjustable from 1.64% to 7.71%/m
obscuration
• Fine protective mesh to prevent insect entry

FPA Equipment Listing #: NI/304

FAPT-851 Acclimate™ Multi-Criteria Sensor Part # Description

• FlashScan protocol FAPT-851AUS FlashScan Acclimate Multi-Criteria Heat/Smoke Sensor
• Photo and Thermal multi-criteria sensing
• Automatically adjusts sensitivity based on
environment
• Capable of “heat-only” alarm mode to
prevent smoke from alarming the device
• Adjustable from 1.3% to 13% obscuration
• Incorporates 63°C fixed temp alarm

FPA Equipment Listing #: NI/301

www.notifier.co.nz 16 Trade Product List 2019

 Addressable Detectors

FST-851(R) Intelligent Thermal Sensor Part # Description

• FlashScan protocol FST-851RAUS – FlashScan rate of rise thermal sensor (ROR 63C) - off
FST-851RAUS
white, Type A
• Fixed Temp or Rate-of-Rise models
available FST-851AUS – FlashScan fixed temperature thermal sensor (Fixed 63C) -
FST-851AUS
• Adjustable from 58°C to 88°C off white, Type B
FST-851HAUS - High Temperature Thermal sensor (Adjustable 63C -88C)
FST-851HAUS
FPA Equipment Listing #: NI/201, 227 - off white, Type D

FST-851(R)-WP Intelligent Sealed Thermal Part # Description

Sensor
FST-851-WP FlashScan fixed temperature sealed thermal sensor (Fixed 63C) - off white

• FlashScan protocol FST-851R-WP (ROR 63C) - off white

• Fixed Temp or Rate-of-Rise models
available
Accessories
FPA Equipment Listing #: NI/207, 208
Part # Description
CP500 Address programmer for FST-851-WP

FSC-851 IntelliQuad™ Multi-Criteria Sensor Part # Description

• FlashScan protocol FlashScan IntelliQuad multi-criteria sensor – CO, Photo, Thermal and
FSC-851AUS
• Multi-Criteria sensing provided by Photo, IR - off white

Thermal, Carbon Monoxide and Infra-Red

sensing elements
• Designed to reduce false alarms
• Capable of “heat-only” alarm mode to
prevent smoke from alarming the device

FPA Equipment Listing #: NI/322

Addressable Reflector type Beam Detector

Part # Description
• FlashScan protocol FSB-200 Beam Detector complete with reflector
• Powered from the SLC FSB-200S Beam Detector with built-in test facility
• Single-ended reflective design
• 10-100m range >70m requires BEAMMMK Accessories
• Ceiling or wall mount unit
• In-built alignment tool Part # Description
• Automatic gain control BEAMSMK Surface Mount Kit for BEAM 1224 for flat surfaces only
• Remote test station available BEAMLRK Long range kit (70-100m)
• FSB-200S includes built-in test station
Multi mount kit - For use when mounting beam detector on ceiling or on an
BEAMMK
angle. Requires BEAMSMK
FPA Equipment Listing #: NI/310
RTS151KEY Key Remote test station with key lock to reset beam detector

www.notifier.co.nz 17 Trade Product List 2019

Addressable Detectors

DETECTOR ACCESSORIES

Universal Addressable Detector Base Part # Description

• Universal for all plug-in addressable detectors B501AUS Universal addressable detector base, off-white

• Colour coded terminal B501AUS-W Universal addressable detector base, pure white
• Tamper proof lock B501AUS-BK Universal addressable detector base, black
• Multiple hole centres
Accessories

Part # Description
SMK-400 Surface mount box for off-white detector base

WB-1AP-IV Wet base shroud for analogue and conventional detectors 200 Series

B524IEFT – Short Circuit Isolator Base Part # Description

• Universal for all plug-in addressable detectors B524IEFT Universal addressable detector base with isolator, off-white
• Tamper proof lock
• Multiple hole centres
• In-built short circuit isolator

FPA Equipment Listing #: NI/660

Coloured Detector Options Part # Description

Replaceable cover for 851 series Photoelectric, BCK-200B/10 Black detector conversion kit for the 851 and 2151B (Pack of 10)

Ionization and Heat detectors. W-200B/1 Detector cover - Pure White to suit 800 series and 2151BAUS

Intelligent Duct Detector Housings Part # Description

• Air velocity rating from 0.5 m/s to 20.32m/s Duct detector housing for intelligent photoelectric detectors, requires
DNR-AUS
• Versatile mounting option. detector and sampling tube

• Replaceable plug-in sensor head (not included) Weatherproof duct detector housing for intelligent detector, requires detector
DNRW
• Backward compatible with Innovair models and sampling tube
• Indoor and Weatherproof (IP66) options
Accessories
NOTE: Requires separate intelligent detector and Part # Description
sampling tube
DST1.5 Sampling tube to suit duct 0.3m to 0.6m

DST3 Sampling tube to suit duct 0.5m to 1.2m

FPA Equipment Listing #: NI/324, 325
DST5 Sampling tube to suit duct 1.2m to 2.4m

DST10 Sampling tube to suit duct 2.4m to 3.7m

ETX Duct detector exhaust tube

www.notifier.co.nz 18 Trade Product List 2019

 Addressable Detectors

Stainless Steal Detector Guard Part # Description

• requires project related approval Stainless steel square detector guard
DETS
Height: 100mm, Width: 110mm, Depth: 60mm

Wire Detector Guard Part # Description

• Protect detector against tamper and STI-9604 White wire detector guard
accidental damage

REMOTE INDICATORS

Remote Indicators Part # Description

• Compatible with conventional and RI-CON Remote indicator “FIRE ALARM – IN CONCEALED SPACE

addressable detectors RI-FLOOR Remote indicator “FIRE ALARM – IN UNDER FLOOR”

• High brightness LED RI-LIFT Remote indicator “FIRE ALARM – IN LIFT SHAFT”
RI-ROOF Remote indicator “FIRE ALARM – IN ROOF”
RI-ROOM Remote indicator “FIRE ALARM – IN ROOM”

Concealed Detector Bracket Part # Description

DETBKT-1 Concealed detector bracket -1m
DETBKT-2 Concealed detector bracket -2m
DETBKT-3 Concealed detector bracket -3m

ADDRESSABLE FIELD I/O MODULES

Addressable Output Modules Part # Description

• FlashScan protocol Single intelligent control (monitored output) module. Requires external
FCM-1
• Control or Relay versions available for creating 24VDC

addressable relay outputs or notification FRM-1 Single intelligent relay output module.
appliance circuits
Accessories
FPA Equipment Listing #: NI615, 614
Part # Description
SMB-500 Surface mount box to suit 500 series modules

www.notifier.co.nz 19 Trade Product List 2019

Addressable Modules

Addressable Monitor Modules Part # Description

• FlashScan protocol FMM-101 Single switch input mini-module

• Switch input or conventional zone versions FMM-1 Single switch input module
available. FZM-1 Single conventional zone interface module Requires external 24VDC

FPA Equipment Listing #: NI/610, 609, 608, 607 Accessories

Part # Description
SMB-500 Surface mount box to suit 500 series modules
ZCM Conventional Zone Conversion Module for FZM-1 and XP6-MA

ISO-X Loop Isolator Module Part # Description

• Isolates section of loop against short ISO-X Loop (SLC) isolator module

circuits. Accessories

FPA Equipment Listing #: NI/613, 619 Part # Description

SMB-500 Surface mount boxt o suit 500 series modules

FDMR-1 Addressable Dual Input/Output Part # Description

Module
FDMR-1 FlashScan dual input/output module

• Ideally suited to AS1668 fan control function

• FlashScan protocol Accessories
• Can disable 1 input and/or 1 output Part # Description
• DIN rail, panel or surface mount accessories M200E-DIN DIN rail mount clip

M200E-PMB Panel mounting clip

FPA Equipment Listing #: NI/613, 619
M200E-SMB-KO Surface mount box with knockouts

SLC Isolator Module Part # Description

• Loop isolator module M700X SLC Isolator module Euro cassette style

• With plug-in screw connections and LEDs

• Euro cassette style Accessories

Part # Description
M200E-DIN DIN rail mount clip
M200E-PMB Panel mounting clip
M200E-SMB-KO Surface mount box with knockouts

ADDRESSABLE HUSH MODULE

Addressable Hush Module Part # Description

HUSHAM NZ Addressable Hush Module
Notifier’s addressable Hush Module is designed to be
used as a component part of a Type 5 - 7e fire alarm
control system.
• Provides a cost effective solution for installations in
residential premises
• Simple installation and mounting
• Operating instructions screened on fascia of the
unit( no additional label required)
• Flexible panel programming for NZS4512:2010
(Type 5 operation)
• Intuitive rotary decade address setting

FPA Equipment Listing #: NI/649

www.notifier.co.nz 20 Trade Product List 2019

 Addressable Manual Call Points

ADDRESSABLE FIELD INPUT & OUTPUT MULTI-MODULES

XP Series Multipoint Monitor Modules Part # Description

• Used to interface with devices such as flow XP-10M 10 way switch input module
and pressure switches, SFIP’s or conventional
6 way Conventional zone interface module
detectors. XP-6MA
Requires external 24V / Rrequires ZCM
• Switch input or conventional zone versions
available ZCM Zone Conversion Module
• Can disable up to 2 unused inputs.
• Mounts in CHS-x chassis

FPA Equipment Listing #: NI/606, 604

XP Series Multipoint Output Modules Part # Description

• FlashScan protocol XP-6R 6 way relay output module
• Control or Relay versions available for creating
addressable relay outputs or notification XP-6C 6 way control output (NAC) module Requires external 24V
appliance circuits
• Can disable up to 2 unused outputs.
• Mounts in CHS-x chassis

FPA Equipment Listing #: NI/607

ADDRESSABLE MANUAL CALL POINTS

Addressable Indoor MCP

Part # Old # Description
NZ MCP with isolator - Indoor red, surface mount with
These MCP’s are designed for use on the two wire MCPANZ FG-05-047
clear cover
communication circuit providing both signaling of an
alarm to the fire indicator panel and local LED indication
of activation. Accessories
• CLIP protocol Part # Old # Description
• Inbuilt loop isolator NZMCPOS FG-42-033 Polycarbonate MCP operation sign
NZFE1612 FG-18-026 Flexible MCP element with Notifier Logo
FPA Equipment Listing #: NI/626
PS200FLAP FG-18-026 Replacement Clear flap cover for MCP
SC070 FG-18-023 Spare test key (pk10)
PS059 FG-18-024 Breakable seal for hinged cover (pk5)
Surface mount bezel and adaptable plate for NZ
NZTB017 FG-18-025
back box
STI-3150 FG-72-016 Weather stopper, clear polycarbonate enclosure

WCP5A Addressable Outdoor MCP Part # Description

These MCP’s are designed for use on the two wire MCPAWNZ NZ MCP with isolator - Outdoor red, surface mount with clear cover

communication circuit providing both signaling of an

alarm to the fire indicator panel and local LED indication Accessories
of activation.
• CLIP protocol Part # Old # Description
• Inbuilt loop isolator NZMCPOS FG-42-033 Polycarbonate MCP operation sign
• IP67 outdoor rating
NZFE1612 FG-18-026 Flexible MCP element with Notifier Logo

FPA Equipment Listing #: NI/627 PS200FLAP FG-18-026 Replacement Clear flap cover for MCP
SC070 FG-18-023 Spare test key (pk10)
PS059 FG-18-024 Breakable seal for hinged cover (pk5)
Surface mount bezel and adaptable plate for NZ
NZTB017 FG-18-025
back box
STI-3150 FG-72-016 Weather stopper, clear polycarbonate enclosure

www.notifier.co.nz 21 Trade Product List 2019

Addressable Modules

ADDRESSABLE LOOP POWERED AV

NFX Series Wall Mount Sounders & Beacons Part # Description

• CLIP protocol NFX-WS-R Addressable Wall Sounder. Red

• Powered from SLC NFX-WSF-RR Addressable Sounder\ Strobe

• Fits to B501AUS plug in base for easy install NFX-WF-RR Addressable Strobe

Accessories

Part # Description
B501AP-IV Plug in base for NFX series
BRR Deep base. Red
BDD Deep base. Off-white
WRR Waterproof base. Red
WDD Waterproof base. Off- white

NFX Series Base Sounders & Beacons Part # Description

• CLIP protocol NFX-BS-IV Addressable Sounder base. Off-white

• Powered from SLC NFXI-BS-IV Addressable Sounder base with isolator

• Fits to B501AP plug in base for easy install NFX-BF-IVR Addressable Strobe base
• Able to fit detector directly to sounder/strobe NFX-BSF-IVR Addressable Sounder/ Strobe base

Accessories

Part # Description
B501AP-IV Plug in base for NFX series
BRR Deep base. Red
BDD Deep base. Off-white
WRR Waterproof base. Red
WDD Waterproof base. Off- white
IBS-LID/DW Lid to suit sounder base (pk10)

www.notifier.co.nz 22 Trade Product List 2019

 Emergency Warning Systems

I-2000 - EMERGENCY WARNING AND COMMUNICATION SYSTEM

The Notifier I-2000 Emergency Warning and Intercommunication System (EWIS) has been designed to facilitate the orderly
and speedy evacuation of a building in the event of an emergency. This procedure may be initiated automatically by a fire
alarm system or manually by a break glass call point.

The I-2000 may be used as a fully automated system or it will allow Fire Wardens to easily control and coordinate an
evacuation using the dedicated emergency telephone network.

• Vertical control layout with up to 3 WIPs per zone

• Any combination of the following amplifiers can be used; 10W, 25W, 50W, 100W and 200W.
• Programmable timers and user configuration can be achieved on site.
• Background music inputs and PABX inputs available with zone selection through keypad control.
• Warden present indicators
• Cascade override
• Remote paging consoles
• Distributed network amplifiers

As these systems are available in any size or configuration, pricing is dependent on the particular design.

FPA Equipment Listing #: NI/401

Warden Intercom Phones Part # Description

• Separate speaker for call tone WIP Handset to suit I-2000 EWIS panel

• Simple two wire connection

• Includes wall mounting bracket
• Compatible with all I2000 systems

Weatherproof Enclosures Part # Description

Surface mount outdoor enclosure in red WIP-BOX-IP66 Weather proof (IP66) surface mount enclosure

• Ideally suited as WIP handset enclosures

• Thumb turn handle (non locked)

Cabinet Dimensions:
- 300mm H x 200m W x 150mm D

www.notifier.co.nz 23 Trade Product List 2019

Emergency Warning Systems

DA SERIES BUILDING OCCUPANT WARNING SYSTEM

DA Series Stand-alone Occupant Part # Description

Warning Systems
DA-30CAB Stand alone 30W occupant warning system with NPS-5 in CAB650

Stand alone occupant warning system DA-60CAB Stand alone 60W occupant warning system with NPS-11 in CAB650
including power supply and battery charger DA-120CAB Stand alone 120W occupant warning system with NPS-11 in CAB650
in metal enclosure.

• Digital pre-recorded speech messages FPA Equipment Listing #: NI/409, 410, 411
• Chime, Lock-down, False alarm and Test
messages
• Ability to synchronize multiple amplifiers
• Includes DA series BOWS and power supply
indications and controls

Cabinet Dimensions:
- CAB650 - 650mm H x 450mm W x 190mm D

DA Series Occupant Warning Modules Part # Description

• Digital pre-recorded speech messages DA-30 30 Watt building occupant warning system

• Chime, Lock-down, False alarm and Test DA-60 60 Watt building occupant warning system
messages DA-120 120 Watt building occupant warning system
• Ability to synchronize multiple amplifiers
• Mounts onto CHS-1L chassis Accessories

Part # Description
CMM-2 CMM-2 – Custom message module (2 x messages)

DA Series Occupant Warning Display Part # Description

Modules
DA Series control and microphone
DA-DISPA
Provides DA series occupant warning system to suit 18u/28u/40u cabinets

amplifiers with manual control and PA DA-DISP/B– DA Series control and microphone
DA-DISPB
functionality. to suit CAB650/CAB900 cabinets
DA-DISP/C – DA Series control module
DA-DISPC
• Designed to be installed in standard to suit 18u/28u/40u cabinets
annunciator slots. DA-DISP/D – DA series PA selector for up to 4 zones
DA-DISPD
Requires a DA-DISP/C for each zone control

SDM-4 Speaker Distribution Module Part # Description

The SDM-4 can be used with a DA series amplifier SDM-4 4 way speaker distribution module
to provide up to 4 individual monitored speaker
circuits.

• 40W output per circuit (max)

• Inputs to disable zones
• Individual S/C and O/C indications

Remote Desktop Paging Console Part # Description

Paging console to provide remote paging MIC/1D Desktop paging console, 1 x Zone

functionality to DA series amplifiers MIC/4D Desktop paging console, 4 x Zones

• CAT5 connection to DA series OWS

• max 300m from OWS

www.notifier.co.nz 24 Trade Product List 2019

 Emergency Warning Ancillaries

CEILING SPEAKERS

SP-100 Ceiling Speaker Part # Description

• Power tappings: 0.375, 0.75, 1.5, 3, 6 W SP-100 Recessed ceiling speaker - 100mm

• SPL: 90dB 1W @ 1m
• Ceiling cut-out: 140mm ø
Accessories

Part # Description
L-SMB-W Surface mount box to suit 4” speaker, White Ø 280mm, depth 75mm

SP-100-BK Black Ceiling Speaker Part # Description

• Power tappings: 0.375, 0.75, 1.5, 3, 6 W SP-100-BK Recessed ceiling speaker (100mm)

• SPL: 90dB 1W @ 1m
Accessories
• Ceiling cut-out: 140mm ø

Part # Description
L-SMB-BK Surface mount box to suit 4” speaker, Black dia. Ø 280mm, depth 75mm

HORN SPEAKERS

SPH-15W Horn Speaker Part # Description

• Power tappings: 0.95, 1.9, 3.75, 7.5, 15 W SPH-15 SPH-15 – 15W Horn Speaker

• SPL: 106dB 1W @ 1m
• Suitable for outdoor (IP66)

Exd Alarm Horn Speakers

Part # Description
• 100V audio line BEXL15D100V BExL15D100V Exd Horn Speaker - 100V line, 15W
• 15W RMS rated output BEXCS110-L2D Exd Alarm Horn\LED Beacon, 110 dB
• 102dB @ 1W
Certified to IEC:-
- II 2G Ex d-IIB T4 Ta. -50oC to +70oC
- II 2G Ex d-IIC T4 Ta. -50oC to +55oC
- II2D Ex tD A21 IP67 T115 **
- Zones 1,2, 21 and 22

HONEYWELL AS7240.24 CERTIFIED

Wall mount Loudspeakers Part # Description

• Intelligible voice and superior sound reproduction 4’’ metal wall mount loudspeaker, 6/3/1.5/0.75W, white metal enclosure, AS
L-VWM06A/ENC
• Robust metal enclosure ISO 7240.24:2015, with capacitor
• Harmonious with all indoor decoration
• Simple power setting
• Easy installation
• AS ISO 7240-24 Certified Type A Speaker / IP21C
• Available with or without capacitor(part number
without “C”)

www.notifier.co.nz 25 Trade Product List 2019

Emergency Warning Ancillaries

HONEYWELL AS7240.24 CERTIFIED SPEAKERS

Part # Description
Ceiling Loudspeakers
4”Ceiling Loudspeaker, 6/3/1.5/0.75/0.375W White
L-VCP06D-W
• Excellent sound reproduction White plastic dome, AS ISO7240. 24: 2015, with capacitor
• Robust plastic/metal dome 4” Ceiling Loudspeaker, 6/3/1.5/0.75/0.375W Black
L-VCP06D-BK
• AS ISO 7240-24 Certified Type A Speaker / IP21C Black plastic dome, AS ISO7240. 24: 2015, with capacitor
• Available with or without capacitor (part 5” Ceiling loudspeaker, 6/3/1.5W White
L-VCP06A/ENC
number without “C”) White plastic dome, AS ISO 7240.24:2015, with capacitor
6.5” Metal ceiling loudspeaker, 6/3/1.5/0.75W White
L-VCM6A/ENC
Red dome, AS ISO 7240.24:2015, with capacitor

Accessories

Part # Description
L-SMB-W Surface mount box to suit 4” speaker White, Ø 280mm, depth 75mm.

L-SMB-BK Surface mount box to suit 4” speaker Black, Ø 280mm, depth 75mm.

Horn Loudspeakers
Part # Description
• Intelligible voice and superior sound reproduction
• Low-profile design blends easily into any Outdoor horn, 15/10/5W, 8ohm, Grey, ABS, AS ISO 7240.24:2015, with
L-VHP15A/EN
outdoor applications capacitor
• Ergonomic and stylish design
• High-strength UV protective UL94V0 ABS housing
• AS ISO 7240-24 Certified Type B Speaker / IP33C
certified (IP 66 compliant)

Projection Loudspeakers Part # Description

• Intelligible voice and superior sound reproduction Unidirectional loudspeaker, 10/5/2.5/1.25W, White, Aluminum, AS ISO
L-VJM10A/ENC
• Ceiling or wall mount 7240.24:2015, with capacitor
• Meets virtually any outdoor requirements Unidirectional projection loudspeaker, 20/10/5/2.5W, White, Aluminum, AS
L-VJM20A/ENC
• AS ISO 7240-24 Certified Type B Speaker / IP33C ISO 7240.24:2015, with capacitor
certified (IP65 compliant) Bidirectional speaker, 20/10/5/2.5W, White, Aluminum, AS ISO 7240.24:2015,
• Available with or without capacitor(part number L-VBM20A/ENC
with capacitor
without “C”)

Column Loudspeakers
Part # Description
• Intelligible voice and superior sound reproduction Outdoor column speaker, 20/10/5/2.5W, White, Aluminum, AS ISO
L-VOM20A/ENC
• Robust aluminum housing 7240.24:2015, with capacitor
• Supplied with universal swivel bracket for Outdoor column speaker, 40/20/10/5W, White, Aluminum, AS ISO
easy angle adjustment L-VOM40A/ENC
7240.24:2015, with capacitor
• Able to be switched between 100V and 70V
• Adapts to extreme environmentw
• AS ISO 7240-24 Certified Type B Speaker / IP33C
certified (IP65 compliant)
• Available with or without capacitor
(part number without “C”)

L-PPP20A – Pendant Speaker

Part # Description
• Suitable for speech and music reproduction L-PPP20A Pendant Speaker
• Robust fire resistant ABS enclosure
• 2m long fire resistant cable
• Not AS7240.24 certified requires project
related approval

INSTALLATION TOOLS

Hole Saws Part # Description

A range of quality hole saws to permit easy HOLESAW-100 140mm Hole saw to suit 4” speakers

installation of suit the Notifier ceiling speakers. HOLESAW-125 165mm Hole saw to suit 5” speakers
ARBOR A6 Arbor to suit hole saw

www.notifier.co.nz 26 Trade Product List 2019

 Emergency Warning Ancillaries

NOTIFICATION APPLIANCES

ENscape Series Wall/Ceiling Sounders

Part # Description
• 2 stage tones CWSO-RR-S1 Surface mount low profile sounder. Red
• Up to 110db (A) output (max)
CWSO-WW-S1 Surface mount low profile sounder. White
• Outdoor (IP65) version
CWSO-RR-W1 Surface mount IP65 sounder. Red
• 12mA alarm current
• 32 tones CWSO-WW-W1 Surface mount IP65 sounder. White

• Synchronized sound
• EN54-3 approved

ENscape Series Sounder with

supplementary Indicator Description
Part #
• 2 stage tones CWSS-RB-S7 Strobe Beacon. Red body, Red Lens, low profile base
• 110dB 110db (A) output (max)
CWSS-RB-W7 Strobe Beacon. Red body, Red Lens, Deep/IP65 base
• Outdoor (IP65) version
• 22mA alarm current
• 32 tones
• Synchronized flash and sound
• Sounder EN54-3 approved Strobe not EN54-23
approved

ENscape Beacons Part # Description

CWST-RB-S7 Signal Beacon, Red body, Red Lens, low profile base
• Excellent light output
• Soft start function to reduce power surges Signal Beacon, Red body, Red Lens,
CWST-RB-W7
• Synchronized flash low Deep/IP65 base
CWST-WA-S7 ENscape Beacon red body, amber lens, low profile base
CWST-WW-S5 ENscape Beacon white body,clear lens low profile base, EN54-23 W & C Class

Mini Horn Sounders

Part # Description
• Up to 91dB output SpectrAlert Mini-Horn Sounder T3 pattern,
MHW
• 13mA alarm current - White
• 12/24VDC operation SpectrAlert Mini-Horn Sounder T3 pattern,
MHR
- Red

SOLEX Series Strobes Part # Description

• 10cd output SOLEX10A Solex Strobe 10Cd - Amber Shallow Base (10-60vdc)

• 10V-60VDC input SOLEX10B Solex Strobe 10Cd - Blue Shallow Base (10-60vdc)
• IP54 with shallow base, IP65 Deep base SOLEX10G Solex Strobe 10Cd - Green Shallow Base (10-60vdc)
• 80mA alarm current SOLEX10R Solex Strobe 10Cd - Red Shallow Base (10-60vdc)

Accessories

Part # Description
SOLEX-WDBR Deep conduit base to suit Roshni/Solex - Red
SOLEX-WDBW Deep conduit base to suit Flashni/Solex - White

www.notifier.co.nz 27 Trade Product List 2019

Emergency Warning Ancillaries

UL- AV Devices Part # Description

SRL- P Red indoor wall mount strobe with clear lens, plain
Features include
• A universal mounting plate with a P2RL-P Red indoor horn strobe 2w, plain

preliminary snap-in feature to hold the SRHK-P Red outdoor strobe, IP66, with clear lens High Candela, Plain/ no label
product in place for the screw attachment
• 7 field-selectable candela settings 15, 30,
75, 95, 110, 135, 185 for wall and ceiling
mount devices.
• Rotary switches to select horn tone and
volume settings. Compatible with 12- or
24-volt systems.
• L-Series horn strobes are listed to UL 1971
and UL 464 for public mode evacuation.

Red and Amber Dual Strobes Part # Description

• 100mA alarm current (per strobe) STR-DUAL Red and Amber Dual strobe on white metal box

• Strong metal mounting box

SRHKRLFIRE Outdoor Brigade Part # Description

Strobe
SRHKRLFIRE SpectrAlert Advance Outdoor Brigade strobe

• 135-185cd adjustable output

• 228 - 286mA alarm current
• Outdoor (IP66) rating
• Labelled “FIRE” in accordance with
requirements of AS1670.1
• Includes surface mount back box

HAZARDOUS AREA NOTIFICATION APPLIANCES

Explosion Proof Strobes Part # Description

• High output 5J or 15J options BEXBGL2D Exd LED beacon - Red Lens, 24V DC
BEXBG05D24DC-RD Exd Strobe, 5J, Red Lens, 24V DC
Certified to IEC:- BEXBG05D24DC-AM Exd Strobe, 5J Amber Lens, 24V DC
- II 2G Ex d-IIC t
BEXBG15D24DC-RD Exd Strobe, 15J Red Lens, 24V DC
- II 2G Ex d-IIC T4 Ta. -50oC to +60oC
BEXBG15D24DC-AM Exd Strobe, 15J Red Lens, 24V DC
- II 2G Ex d-IIC T5 Ta. -50oC to +55oC
- II 2G Ex d-IIC T6 Ta. -50oC to +40oC
- II 2D Ex tD IIC A21 T115oC Db IP67
- Zones 1, 2, 21 and 22

Explosion Proof Alarm Horns Part # Description

• High 110dB or 120dB output BEXS110D24DC Exd Alarm Horn, 110 dB

• 45 tone settings BEXS120D24DC Exd Alarm Horn, 117 dB

Certified to IEC:-
- II 2G Ex d-IIB T4 Ta. -50oC to +70oC
- II 2G Ex d-IIC T4 Ta. -50oC to +55oC
- II2D Ex tD A21 IP67 T115 **
- Zones 1,2, 21 and 22

www.notifier.co.nz 28 Trade Product List 2019

 Emergency Warning Ancillaries

IS-A105N-R Intrinsically Safe Horn Sounder

Part # Description
• 105dB output
IS-A105N-R Intrinsically safe Horn Sounder 24VDC, Red
• 49 tone settings and 3 input stages

Certified to IEC:-
- II 1G Ex ia-IIC T4 Ga. -40oC < Ta < +60oC
- Zone 0

IS-mA1-R Intrinsically Safe ‘Minialarm’

Sounder

• 100db output Part # Description

• 49 tone settings and 3 input stages IS-MA1-R Intrinsically safe Mini alarm Sounder 24VDC, Red

Certified to IEC:-
- II 1G Ex ia-IIC T4 Ga. -40oC < Ta < +60oC
- Zone 0

IS-mC1-R Intrinsically Safe ‘Minialert’

Combined Sounder/Beacon Part # Description
• 100db output IS-MC1-R/R Minialert combined sounder/beacon, 24VDC, Red

• 24cd beacon output

• 49 tone settings and 3 input stages

Certified to IEC:-
- II 1G Ex ia-IIC T4 Ga. -40oC < Ta < +60oC
- Zone 0

IS-mB1 Intrinsically Safe ‘Minialite’ Beacon

Part # Description
• 24cd beacon output IS-MB1-R/R Intrinsically safe Minialite red lens
IS-MB1-R/A Intrinsically safe Minialite amber lens
Certified to IEC:-
- II 1G Ex ia-IIC T4 Ga. -40oC < Ta < +60oC IS-MB1-R/B Intrinsically safe Minialite blue lens

- Zone 0

IS-L101L Intrinsically Safe LED Beacon Part # Description

• 48cd beacon output IS-L101L-R/R Intrinsically safe LED Beacon red lens
IS-L101L-R/A Intrinsically safe LED Beacon amber lens
Certified to IEC:- IS-L101L-R/B Intrinsically safe LED Beacon blue lens
- II 1G Ex ia-IIC T4 Ga. -40oC < Ta < +60oC
- Zone 0

FIRE BELLS

Part # Description
SSM Series Fire Bells
SSM24-6 6” (150mm) Alarm bell – 24VDC
SSM series alarm bells are low current, high SSM24-8 8” (200mm) Alarm bell – 24VDC
decibel notification appliances for use in fire or SSM12-6 6” (150mm) Alarm bell – 12VDC
other signaling applications.
Accessories
• High dB output
Part # Description
• Suitable for indoor and outdoor use
• Low current draw WBB Back Box to suit Bells –Red

Fire alarm bells for hazardous areas (Exd) Part # Description

BEXSB1DC24G Exd 8” Fire Bell Red, 24V
BEXSB1AC230G Exd 8" Fire Bell Red, 240Vac low current high decibel

www.notifier.co.nz 29 Trade Product List 2019

Agent Release Equipment

AGENT RELEASE MODULE

The Notifier Agent release module is used to

Part # Description
control the release of suppressing agents in
ARM Agent Release Module Kit
accordance with AS4214 or AS14520.1

• Dual risk operation from 3 risk inputs Accessories

• Optional Pyrozone interface
• Master “Service Isolate” button Part # Description
• Fits into 1 x CHS-xL slot LCS-SW Spare Switch

AGENT RELEASE LOCAL CONTROL STATION (LCS)

The Notifier local control station is used for Part # Description

connection to a gas control panel for remote
LCS Agent release local control station
control of the suppression agent isolation and
release.
Accessories
• Simple to install, flip down enclosure
• Interfaces to Notifier Agent Release module Part # Description
LCS-SW Spare Switch
Enclosed Dimensions (Standard LCS)
- 190mm Hx 110mm Wx 80mm D

Enclosure Dimensions (Standard LCS): Part # Description

- 190mm H x 110mm W x 80mm D
STI-3150 Weather stopper, clear polycarbonate enclosure
STI-1130 Indoor Protective cover Stopper II® with Horn & Clear Spacer, Fire Label / red
horn/clear space

www.notifier.co.nz 30 Trade Product List 2019

 Agent Release Equipment

ILLUMINATED WARNING SIGNS

Indoor Red Warning Sign (body only) Part # Description

• Attractive slim-line sign WSR-I Red Indoor Warning Sign (body only)

• Integrated piezo sounder

• High brightness red LED illumination Face Plates
• Range of standard face plates
Part # Description
• Black sign coloured text
WSF-I/CUST Indoor Face plate Customer Specified Text
WSF-I/FA-DNE Indoor Face Plate “FIRE ALARM, DO NOT ENTER”
WSF-I/FA-EA Indoor Face Place “FIRE ALARM, EVACUATE AREA”
WSF-I/FDC Indoor Face Plate “FIRE DOOR CLOSING”
WSF-I/DNE-GD Indoor Face Plate “DO NOT ENTER, GAS DISCHARGED”

Outdoor Red Warning Sign (body only) Part # Description

• IP66 outdoor rating WSR-O Outdoor Red Warning Sign (body only)

• Integrated piezo sounder

• High brightness red LED illumination Face Plates
• Range of standard face plates
• Black sign coloured text Part # Description
WSF-O/CUST Outdoor Face plate, Customer Specified Text
WSF-O/FA-DNE Outdoor Face Plate “FIRE ALARM, DO NOT ENTER”
WSF-O/FA-EA Outdoor Face Place “FIRE ALARM, EVACUATE AREA”
WSF-O/FDC Outdoor Warning Sign Fascia “Fire Door Closing”

WSF-O/DNE-GD Outdoor Face Plate “DO NOT ENTER, GAS DISCHARGED”

Indoor System Inoperative Warning Sign Part # Description

• Attractive slim-line styling WSA-I/SI Indoor “System Inoperative” Warning Sign

• Integrated piezo sounder

• High brightness amber LED illumination
• System Inoperative faceplate for use with
agent release systems
• Black sign coloured text

Outdoor System Inoperative Warning Part # Description

Sign
WSA-O/SI Outdoor “System Inoperative” Warning Sign

• IP66 outdoor rating WS-FIRE Warning Sign - “FIRE” 150mm x 60mm, red on white
• Integrated piezo sounder WS-FIP Warning Sign - “FIRE INDICATOR PANEL”, red on white
• High brightness amber LED illumination WS-000 Warning Sign - “Dial 000, Local Fire Alarm Only”, red on white, 80 x 25mm
• System Inoperative faceplate for use with
Warning Sign - “WARNING - FIRE DOOR CLOSING”,
agent release systems WS-WFDC
non-illuminating, 730mm(w) x 200mm(h)
• Black sign coloured text

www.notifier.co.nz 31 Trade Product List 2019

Ancillaries

HAZARDOUS AREA MANUAL CALL POINTS

EXD Manual Call Point Part # Description

Certified to IEC:- Red ExD Manual Call Point with protective flap,
BEXCP3A-BG-LF
- Ex e d-IIC T6 Gb (-40oC ≤ Ta ≤ +55oC) no resistors

- Ex t-IIIC T60 Db (-40oC ≤ Ta ≤ +55oC)

WCP3A-IS Intrinsically Safe Conventional Part # Description

Outdoor MCP
Red surface mount Intrinsically safe MCP,
WCP3A-R-IS
• Outdoor (IP67) ratin House + Flame

• Nor ally Open and Nor ally Closed operation

• Flexible (non-glass) element available Accessories

Part # Description
Certified to IEC:-
SG-1X10 Spare MCP glass (pk 10), common to all MCP’s
- Ex ia-IIB T4 Ga (-30oC ≤ Ta ≤ +40oC)
Clear replacements flap to cover MCP from accidental breakage suits all
- Zones 0, and 20 PS200FLAP
KAC MCP’s - curved shape
PS210 Flexible MCP element
SC070 Spare test key (pk 10), to suit all MCPs

MAGNETIC DOOR HOLDERS

Surface Mount Magnetic Door Holders Part # Description

• 400/1000N Holding force MDH400 MDH400 Magnetic Door Holder 400N (41kg)

• Spark suppression MDH1000 MDH1000 Magnetic Door Holder 1000N (102kg)

• Reverse polarity diode fitted
Accessories

Part # Description
MDHW15 Wall mount extension bracket 15cm

MDHW30 Wall mount extension bracket 30cm

MDH/F Floor Mount Bracket

Floor/Wall Mount Magnetic Door Holders Part # Description

• 15/30cm arm legths MDH400/15 Wall or Floor mount magnetic door holder 400N (41kg) with 15cm arm

• Spark suppression MDH400/30 Wall or Floor mount magnetic door holder 400N (41kg) with
MDH400/30
• Reverse polarity diode fitted 30cm arm

Accessories

Part # Description
SZ2575 Surface mount box for MDH400/15 or MDH400/30

www.notifier.co.nz 32 Trade Product List 2019

 Ancillaries

MDH1350 Magnetic Door Holder Part # Description

MDH1350 Surface mount magnetic door holder,
MDH1350
60mA (50kg)

Remote Door Release Part # Description

MDHREM Remote door release plate
Remote door release switch for magnetic door
holders, fitted onto Clipsal style switch plate

FLAME DETECTORS

FSL100 Flame Detectors Part # Description

Honeywell’s FSL100 range of Light Industrial/ UV flame detector Suitable for ATEX zone 2/22; FM 3611 Class 1,2&3 Div2 EN54-
Commercial Flame Detectors enables simple FSL100-UV
10 (HIGH sensitivity) certificate FM3260 approval (pending*). Red Housing
coverage of fire hazard areas across many fire hazard
applications. Installation, set-up and operation are
simple. Wide solid area coverage and fast speed UV flame detector Suitable for ATEX zone 2/22; FM 3611 Class 1,2&3 Div2 EN54-
FSL100-UV-W
of response optimize safety. With inbuilt automatic 10 (HIGH sensitivity) certificate FM3260 approval (pending*). White Housing
test and test lamps available to cover all models,
reliability is ensured.
UV/IR flame detector Suitable for ATEX zone 2/22; FM 3611 Class 1,2&3 Div2
Key Features & Benefits FSL100-UVIR
EN54-10 (HIGH sensitivity) certificate FM3260 approval (pending*). Red Housing
• UV, UV/IR and IR3 Flame Detectors to cover a wide
range of applications UV/IR flame detector Suitable for ATEX zone 2/22; FM 3611 Class 1,2&3 Div2
• Robust, simple to install & set-up; Wide angle and FSL100-UVIR-W EN54-10 (HIGH sensitivity) certificate FM3260 approval (pending*). White
fast speed of response Housing
• Automatic test and test lamps for simple check and
Triple IR flame detector Suitable for ATEX zone 2/22; FM 3611 Class 1,2&3 Div2
maintenance.
FSL100-IR4 EN54-10 (HIGH sensitivity) certificate (pending*) FM3260 approval (pending*).
Red Housing
Quick Specs Triple IR flame detector Suitable for ATEX zone 2/22; FM 3611 Class 1,2&3 Div2
• FSL100 Flame Detectors - UV, UV/IR and IR3 for FSL100-IR3-W EN54-10 (HIGH sensitivity) certificate (pending*) FM3260 approval (pending *).
light industrial applications White Housing
• GRP Housing, available in Red or White with
optional swivel mount
• 24 VDC nominal (10-28VDC), 25mA nominal Accessories
operation
• 4 to 20mA and Relay outputs. Part # Description
• EN54-10 Performance Approved FSL100-SM22 FSL100 Optional swivel mount

www.notifier.co.nz 33 Trade Product List 2019

Flame Detection

FS20X Flame Detector Part # Description

Part of the FSX family of electro-optical flame
DUAL IR/UV FLAME DETECTOR Copper-Free Aluminum Encl. with (2) M25
detectors, the FS20X UV/IR2/VIS represents a FS24X-911-23-6
entries, FM, cFM, ATEX, IECEx for Class I, Zone 1. With EN54-10 certification
quantum leap in integrating infrared and ultraviolet
sensing technologies.
Key Features & Benefits DUAL IR/UV FLAME DETECTOR Stainless Steel Encl. with (2) M25 entries, FM,
FS20X-211-24-6
cFM, ATEX, IECEx for Class I, Zone 1. With EN54-10 certification
• Detects hydrocarbon and non-hydrocarbon fuel
fires in all environmental conditions
• Range greater than 200 feet to 1 sq. ft. heptane fire
• Arc welding immunity Accessories
Quick Specs
Part # Description
• UV / IR2 / VIS Flame Detection Technology
• Field of view: 90° full 100% core of vision, ± 45° SM4 Stainless Steel Swivel mounting assembly for FS24X,SS4, SS2 detectors
from on axis
• Operating voltage: 24 VDC nominal (18-32 VDC) - SH-001 Sunshield for FS20X & FS24X Detectors, 316 Stainless Steel
regulated
• Sensitivity: Very high, high, medium and low - IR Test lamp for testing FS20X & FS24X detectors,
TL-2055
switch selectable explosion proof version. Incl universal charger
• 4 to 20mA and Relay outputs. IR Test lamp for testing FS20X & FS24X detectors,
• IECEx Certified Ex d for use in Gas Zone 1 TL-1055
non-explosion proof version. Incl universal charger
Hazardous Areas
• EN54-10 Performance Approval Universal charger for Fire Sentry Test Lamps and Interface Kits. For 110-240
PSU-12
VAC with international plugs

FS24X Flame Detector Part # Description

Sophisticated software algorithms and dual micro QuadBand™ IR3+ Detector, Copper-Free Aluminum Encl., (2) M25 entries FM,
FS24X-911-23-6
processors ensure that the FS24X IR3/VIS flame cFM, IECEx, ATEX and EN54-10 approved
detector has the highest fire detection performance QuadBand™ IR3+ Detector, 316 Stainless Steel Encl. (2) M25 entries FM, cFM,
combined with optimal false alarm rejection. FS24X-911-24-6
IECEx, ATEX and EN54-10 approved
Key Features & Benefits
• Detects hydrocarbon and non-hydrocarbon fuel
fires in all environmental conditions Accessories
• User selection outputs
• Optimal false alarm rejection Part # Description
Quick Specs Stainless Steel Swivel mounting assembly for
M4
• IR3 / VIS Flame Detection Technology FS24X,SS4, SS2 detectors
• Sensitivity: Very high, high, medium and low -
switch selectable H-001 Sunshield for FS20X & FS24X Detectors, 316 Stainless Steel
• Operating voltage: 24 VDC nominal (18-32 VDC)
IR Test lamp for testing FS20X & FS24X detectors,
- regulated TL-2055
• Humidity range: 5 to 98% relative humidity, non- explosion proof version. Incl universal charger
condensing IR Test lamp for testing FS20X & FS24X detectors,
TL-1055
• 4 to 20mA and Relay outputs. non-explosion proof version. Incl universal charger
• IECEx Certified Ex d for use in Gas Zone 1
Hazardous Areas
• EN54-10 Performance Approval

www.notifier.co.nz 34 Trade Product List 2019

 Gas Detection

XCD GAS DETECTORS

Sensepoint XCD gas detectors Part # Description

The Sensepoint XCD range of fixed gas detectors XCD Flammable CAT, 0-100%LEL (20,0 to 100.0%LEL) with LM25 Aluminium
SPXCDALMFX
is used to monitor areas where flammable, Alloy, M20 Entry

oxygen deficiency and toxic gasses may pose a SPXCDASMFX XCD Flammable CAT 0-100%LEL (20,0 to 100.0%LEL) with SS316, M20 Entry
hazard to working environments. XCD is designed
for a broad spectrum of industrial applications XCD CH4(Methane) IR, 0-100%LEL (20,0 to 100.0%LEL) with LM25
SPXCDALMRX
with a comprehensive choice of features and Aluminium Alloy, M20 Entry
benefits in a cost effective package.
SPXCDASMRX XCD CH4(Methane) IR 0-100%LEL (20,0 to 100.0%LEL) with SS316, M20 Entry

• AS3786 approved
SPXCDALMO1 XCD Oxygen, 25.0%/Vol with Aluminium Alloy, M20 Entry
• Includes field replaceable sensor
• Built in sounder
SPXCDASMO1 XCD Oxygen 25.0%/Vol with SS316, M20 Entry
• N/A and N/C Alarm contacts
• Interconnect up to 24 units XCD Hydrogen Sulphide 0-50ppm (10.0 to 100.0ppm) with LM25 luminium
SPXCDALMHX
Alloy, M20 Entry
Certified to IEC:-
- II 2G Ex d-IIC t SPXCDASMHX XCD Hydrogen Sulphide 0-50ppm (10.0 to 100.0ppm) with SS316, M20 Entry

- Ex d IIC T4 Gb. T6(Ta -40oC to +65oC) XCD Carbon Monoxide 0-500ppm (100 to 1000ppm) with Aluminium Alloy,
- Ex tb IIIC T85oC Db IP66 SPXCDALMCX
M20 Entry

Certified to ATEX:- SPXCDASMCX XCD Carbon Monoxide 0-500ppm (100 to 1000ppm) with SS316y, M20 Entry
- Ex d IIC T4 GD T6(Ta -40oC to +65oC)
XCD Hydrogen0-1000ppm with Aluminium Alloy,
- Ex tb IIIC T85oC Db IP66 SPXCDALMG1
M20 Entry
ATEX/IECEX & AP approved SP XCD Hydrogen 0-1000ppm with SS316, M20
SPXCDASMG1
Entry

SPXCDALMB1 XCD CO2(Carbon Dioxide) IR 0-2%VOL with Aluminium Alloy, M20 Entry

ATEX/IECEX & AP approved SP XCD CO2

SPXCDASMB1
(Carbon Dioxide) IR 0-2%VOL with SS316, M20

Unipoint Gas Detector Controllers Part # Description

UniPoint Controller (mV input Version)
DIN rail mounted controller for Sensepoint XCD 2306B2000
DIN rail mounting
gas detectors.
UniPoint Controller (mA input Version)
2306B1000
• 2 or 3 wire 4-20mA inputs DIN rail mounting
• 3 x alarm, 1 x fault relays

www.notifier.co.nz 35 Trade Product List 2019

Linear Heat Detection

FIBRE OPTIC LINEAR HEAT DETECTION

AP Sensing DTS Fibre Optic Linear Heat Detection

AP Sensing’s fiber optic, linear heat detection systems leave no area unmonitored and display the real-time
temperature and heat transfer of the entire area at once. Based on the quantum mechanical RAMAN-effect and
a patented code-correlation measurement technique AP Sensing’s “Linear Heat Series” measures an accurate
temperature profile along the optical fiber over several thousand meters with measurements every 10 seconds.
With an extremely high level of integration and unique optical assembly technology, AP Sensing offers you full
protection combined with worry free permanent operation.

Enabling fast, reliable and cost-effective sensing through highly integrated optical measurement systems.
AP Sensing DTS will provide temperature monitoring for;

• Fire Detection
• Power cable monitoring
• Oil & Gas downhole performance monitoring
• Pipeline leakage detection

Suitable applications include large distributed manufacturing facilities, refineries, power plants, silos,
warehouses, cold stores, conveyor belt systems, cable trays and tunnels
• Suitable for Harsh and Hazardous areas
• Continuous temperature monitoring
• Ability to integrate into management systems

GENERAL PURPOSE LINEAR HEAT DETECTION

68 deg C
System Sensor Linear Heat Detection
Part # Description
System Sensor’s linear heat detection system SS-LD-68-155-100 Linear Heat Cable 68deg, 100m roll
is a fixed temperature device consisting of the
SS-LD-68-155-200 Linear Heat Cable 68deg, 200m roll
conductor cable and an EOL box.
SS-LD-68-155-500 Linear Heat Cable 68deg, 500m roll

When heated to the rated temperature, the SS-LD-68-155-1000 Linear Heat Cable 68deg, 1000m roll
heat sensitive polymer insulation melts
allowing the inner conductors to contact each 78 deg C
other initiating an alarm state. Part # Description
SS-LD-78-172-100 Linear Heat Cable 78deg, 100m roll
This type of detection is widely used in
SS-LD-78-172(200M) Linear Heat Cable 78deg, 200m roll
industrial, petrochemical, refinery and power
generation plants. SS-LD-78-172-500 Linear Heat Cable 78deg, 500m roll
SS-LD-78-172-1000 Linear Heat Cable 78deg, 1000m roll
• Continuous sensitivity along the length of
cable 88 deg C
• Easy to install, test and splice
Part # Description
SS-LD-88-190-100 Linear Heat Cable 88deg, 100m roll
FPA Equipment Listing #: SS-LD-88-190-200 Linear Heat Cable 88deg, 200m roll
NI/ 209, 210, 211, 212
SS-LD-88-190-500 Linear Heat Cable 88deg, 500m roll
SS-LD-88-190-1000 Linear Heat Cable 88deg, 1000m roll

105 deg C

Part # Description
SS-LD-105-220-100 Linear Heat Cable 105deg, 100m roll
SS-LD-105-220-200 Linear Heat Cable 105deg, 200m roll
SS-LD-105-220-500 Linear Heat Cable 105deg, 500m roll
SS-LD-105-220-1000 Linear Heat Cable 105deg, 1000m roll

Accessories
Part # Description
8687/EOL 47k End of line box
MB LHD Junction Box to suit linear heat cable

www.notifier.co.nz 36 Trade Product List 2019

 Linear Heat Detection

HARSH AREA LINEAR HEAT DETECTION

System Sensor Linear Heat Detection 68 deg C

with Nylon coating
Part # Description
System Sensor’s linear heat detection system SS-LDN-68-155-100 Linear Heat Cable 68deg, with nylon coating, 100m roll
is a fixed temperature device consisting of the
SS-LDN-68-155-200 Linear Heat Cable 68deg, with nylon coating, 200m roll
conductor cable and an EOL box.
SS-LDN-68-155-500 Linear Heat Cable 68deg, with nylon coating, 500m roll

When heated to the rated temperature, the SS-LDN-68-155-1000 Linear Heat Cable 68deg, with nylon coating, 1000m

heat sensitive polymer insulation melts

allowing the inner conductors to contact each
78 deg C
other initiating
an alarm state. Part # Description
SS-LDN-78-172-100 Linear Heat Cable 78deg, with nylon coating, 100m roll
This type of detection is widely used in
SS-LDN-78-172-200 Linear Heat Cable 78deg, with nylon coating, 200m roll
industrial, petrochemical, refinery and power
generation plants. SS-LDN-78-172-500 Linear Heat Cable 78deg, with nylon coating, 500m roll
SS-LDN-78-172-1000 Linear Heat Cable 78deg, with nylon coating, 1000m
• Continuous sensitivity along the length of
cable
• Easy to install, test and splice 88 deg C
• Chemical resistant Part # Description
• UV resistant SS-LDN-88-190-100 Linear Heat Cable 88deg, with nylon coating, 100m roll
SS-LDN-88-190-200 Linear Heat Cable 88deg, with nylon coating, 200m roll
FPA Equipment Listing #:
SS-LDN-88-190-500 Linear Heat Cable 88deg, with nylon coating, 500m roll
NI/ 213, 314, 215, 216
SS-LDN-88-190-1000 Linear Heat Cable 88deg, with nylon coating, 1000m

105 deg C

Part # Description
SS-LDN-105-220-100 Linear Heat Cable 105deg, with nylon coating, 100m
SS-LDN-105-220-200 Linear Heat Cable 105deg, with nylon coating, 200m
SS-LDN-105-220-500 Linear Heat Cable 105deg, with nylon coating, 500m
LDN-105-220(1000m) Linear Heat Cable
SS-LDN-105-220-1000
105deg, with nylon coating, 1000m

Accessories

Part # Description
8687/EOL 47k End of line box
MB LHD Junction Box to suit linear heat cable

www.notifier.co.nz 37 Trade Product List 2019

Aspirated Smoke Detection

VESDA DETECTORS

VESDA-E VEU

The VEU series of aspirating smoke detectors Part # Description

are the premium detector of the VESDA-E
VEU-A00 VESDA-E VEU with LED display
range. A range of revolutionary new features
VEU-A10 VESDA-E VEU with 3.5” Display
provide unsurpassed detection performance,
flexibility, field programmability, connectivity
and reduced total cost of ownership. FPA Equipment Listing#: VS/ 337, 338
• Ultra-wide sensitivity range; 15 times greater
than VESDA VLP
• Provision for more sampling holes provide
an increased coverage in high airflow
applications by at least 40%
• Considerably longer linear pipe runs
and extended branched pipe network
configurations cater perfectly to applications
with higher ceilings providing an increased
coverage by up to 80%
• Convenient detector mounting for ease of
service and maintenance

Intelligent VESDA-E VEP

Part # Description
Intelligent VESDA-E VEP aspirating smoke detectors VEP-A00-1P-NTF Intelligent VEP single pipe, up to 1000 sq. m through one pipe
are seamlessly integrated on the SLC loop with
VEP-A00-P-NTF
NOTIFIER fire alarm control panels for a complete
very early warning fire system. It bring the latest and VEP-A10-P-NTF Intelligent VEP four pipes, up to 2,000 sq. m through four pipes
most advanced detection technology forming the
new Aspirating Smoke Detection (ASD) benchmark.
Intelligent VEP is built on the new Flair technology
- a revolutionary detection chamber that uses
direct imaging of the sampled particles via a CMOS
image combined with multiple photo-diodes. The
Flair detection chamber in VEP provides very early
warning smoke detection, fewer nuisance alarms,
higher stability and increased longevity to apply
in wide range of applications.VEP delivers a range
of revolutionary features that provide user value
such as longer pipe runs, out-of-box operation, field
replaceable components, WiFi connectivity, 3.5” touch
screen & remote monitoring via iVESDA. It is backward
compatible with the world’s number one ASD, VLP
allowing significant upgrade opportunities.

Features & Benefits

• Seamless integration with the SLC loop of NOTIFIER
fire alarm control panels
• One and four pipe models for different applications
• Alarm and trouble status reporting at the fire alarm
control panel without using any additional hardware
• FLAIR detection technology delivers reliable very
early warning smoke detection
• Multi-stage filtration
• Intuitive LCD user interface
• Airflow monitoring at each port
• Referencing to accommodate external
environmental conditions to minimize nuisance
alarms
• Backwards compatible with VESDA VLP
• Remote monitoring with iVESDA mobile app
• Configuration through VESDA VSC application

www.notifier.co.nz 38 Trade Product List 2019

 Aspirated Smoke Detection

VESDA DETECTORS

VESDA-E VEP

The VESDA-E VEP series of smoke detectors bring Part # Description

the latest and most advanced detection technology VEP-A00-1P VESDA-E VEP with LEDs, Plastic Enc.
to provide very early warning and the best nuisance
VEP-A00-4P VESDA-E VEP with LEDs, Plastic Enc.
alarm rejection to a wide range of applications.
VEP-A10-4P VESDA-E VEP with 3.5”Disp, Plastic Enc.
Built on the Flair detection technology and years
of application experience, VEP detectors achieve
consistent performance over their lifetime via
FPA Equipment Listing#: VS/ 339, 340
absolute calibration. In addition, the VEP delivers
a range of revolutionary features that provide user
value.
• One and four pipe models for different
applications
• Flair detection technology delivers reliable very
early warning in a wide range of environments
with minimal nuisance alarms
• Multi stage filtration and optical protection
with clean air barriers ensures lifetime detection
performance
• Four alarm levels and a wide sensitivity range
deliver optimum protection for the widest range
of applications
• Intuitive LCD icon display provides instant status
information for immediate response

VESDA Laser FOCUS

Part # Description
• Single Pipe
VLF-250 Relays Only
• Single Zone
• Instant Fault Finder™ VLF-500 Relays Only

• AutoLearn™ Smoke VIC-020 Multi-function Card – 2 x relays, 1 x input

• AutoLearn™ Flow VIC-030 Multi-function Card – 3 x relays, 1 x input

FPA Equipment Listing#: TBC

VESDA Laser COMPACT

Part # Description
VLC-500 Relays Only
• Single Pipe
• Single Zone VLC-505 VESDAnet Version
• AutoLearn™ Smoke VLX-100 VLC in EEX Housing inc flame arrestors
VLC-505-EX VESDA Laser Compact (VN) Exn Zone 2 - 800m2
FPA Equipment Listing#: VS/307, 308, 304

www.notifier.co.nz 39 Trade Product List 2019

Aspirated Smoke Detection

VESDA Laser PLUS Part # Description

• Four Pipes VLP-002 2 x Blank plates & Display

• One Zone VLP-012 1 Blank plate & Display & Programmer

• AutoLearn™ Smoke VLP-400 with Fire 1 & OK LED’s fitted

FPA Equipment Listing#: VS/309

Part # Description
VESDA Laser SCANNER with 7
VLS-204 Vesda FD7 Scanner, 2x Blank, Display, 7 Relays fitted
Relay
VLS-210 Vesda FD7 Scanner, 2x Blank, Programmer, 7 Relays fitted
Termination Card
VLS-214 Vesda FD7 Scanner, 1 Blank plate & Display & Programmer
• Four Pipes Vesda FD7 Scanner, Blank with FIRE 1 and OK LED’s plus Blank, Blank and 7
VLS-600
• Four Zones Relays
• AutoLearn™ Smoke

FPA Equipment Listing#: VS/310

Part # Description
VESDA Laser SCANNER with 12 Relay
Termination Card Vesda FD12 Scanner, Blank with FIRE 1 and OK LED’s plus Blank, Blank and
VLS-700
12 Relays
• Four Pipes VLS-304 Vesda FD12 Scanner, 2x Blank Display, 12 Relays fitted
• Four Zones VLS-310 Vesda FD12 Scanner, Blank, Programmer, Blank, 12 Relays
• AutoLearn™ Smoke
VLS-314 Vesda FD12 Scanner, 2x Blank, Display, Programmer, 12 Relays

FPA Equipment Listing#: VS/310

VESDA Laser INDUSTRIAL Part # Description

• Four Pipes VLI-880 VESDA VLI with Relays

• Four Zones VLI-885 VESDA VLI with VesdaNET

• AutoLearn™ Smoke

FPA Equipment Listing#: VS/333

VESDA ACCESSORIES

Part # Description
VHH-100 Hand Held Programmer inc Cable
VHX-1200 HLI – Wall mounted inc VESDAnet socket
VHX –0200 HLI – Vesdanet PC Link Windows, used with VSM3
VHX-1420-HFS Modbus HLI (Honeywell version) to suit Vesda Net gateway

www.notifier.co.nz 40 Trade Product List 2019

 FAAST Smoke Detectors

Remote Units Part # Description

VRT-000 Remote box with escutcheon only no blank plate
VRT-100 Remote box fitted with programmer
VRT-200 Remote box fitted with VLP display and 7 relays
VRT-300 Remote box fitted with VESDAnet socket
VRT-400 Remote box fitted with Scanner display and 7 relays
VRT-700 Remote box fitted with Scanner display no relays
VRT-800 Remote box fitted with Scanner display and 12 relays
VRT-900 Remote box fitted with Blank Plate and 12 Scanner relays
VRT-V00 VLF Remote display with RTC7
VRT-J00 Vesda VLC VN Remote display with RTC7
VRT-Q00 Vesda VLI Remote Display with RTC7
VRT-T00 Vesda VLI Remote Display with RTC0
VIC-010 VESDANet Interface card to suit VESDA
VRT-S07 System Relay Module
VRT-E00 Remote Box fitted with blank plate DRP & 7 relay card Scanner
VRT-K00 Remote Box fitted w/VLC VN Display & relay RTC

ASPIRATED DETECTOR PIPE & FITTINGS

An extensive range of aspirated detector pipe, bends,

Part # Description
fittings and sampling points to enable the creation of
E700-P Pipe per 4 meter length
the required pipe and detection network.
E700-PJ Pipe Junction fitting
E700-LB Large Radius Bend (150mm)
E700-SB Small Radius Bend (90mm)
E700-J J-Piece pipework
E700-EC Pipe End Cap
E700-ASP Aspirated Pipe Clip (HILTI) to suit 25 mm aspirated detector pipe
E700-T ABS Solid T Pieces
E700-TA Truck Adaptor for capillary tubes
E700-CSC Sampling Connector for Capillary tubes
E700-CT Capillary tube 5.2mm ID 8mm OD per metre
E700-SP Sampling Point for Capillary tube end
E700-SP-DCL Sampling point decal (200 per roll)
E700-SPLR Sampling point label RED (ea)
E700-HASP Heat Activated Sampling Point
E700-SRB Standard base for HASP (use extra CSC)

www.notifier.co.nz 41 Trade Product List 2019

Osid Open Area Detection

OSID OPEN AREA DETECTION

OSID Emitters Part # Description

• Dual frequency beam OSE-SP OSID Emitter Standard Power/Battery Version

• Multiple emitters for power input OSE-HP-01 OSID Emitter - High Power, Alkaline battery
• Ball & Socket adjustment OSE-SPW OSID Emitter Standard Power/24V Wired Version
• Laser alignment tool OSE-HPW OSID Emitter High Power/24V Wired Version

FPA Equipment Listing #: VS/330, 331, 332

Accessories

Part # Description
OSID-EHE OSID Emitter Environmental Housing
OSID-WG OSID Wire Cage
OSE-ACF OSE Anti-Condensation film to suit OSID-EHE (10pk)

OSID Imagers Part # Description

OSI-10 OSID Imager 7 degree coverage (min 25m)
• CMOS chip imager
• Multiple angle of coverage OSI-90 OSID Imager 80 degree coverage
• Ball & socket adjustment
Accessories
FPA Equipment Listing #: VS/327, 328, 329
Part # Description
OSID-EHI Imager Environmental Housing to suit OSID, IP66
OSID-WG Wire Cage to suit OSID
OSEH-ACF Anti-condensation to suit OSID-EHI (10pk)

OSI-LS Light shield for OSI-10

OSP-001 OSID FTDI Cable 1.5m

OSP-002 OSID Laser Alignment Too
OSE-RBL Battery Exchange Unit Lithium exchange unit
SE-RBA Emmitter Spare Battery Alkaline battery

OSID Installation tools Part # Description

OSID-INST OSID Install Kit

www.notifier.co.nz 42 Trade Product List 2019

 Power Supplies & Batteris

NPS SERIES POWER SUPPLY

NPS Series Stand-Alone Power Supplies Part # Description

2.7A power supply in cabinet.
24VDC power supply and battery charger in
NPS-2BB Fits 12AH batteries
enclosure. Ideal for use as a remote power supply
(230mm H x 350mm W x 130mm D) – Oyster Grey
for external equipment such as VESDA detectors.
5.6A power supply in cabinet.
NPS-5BB Fits 40AH batteries
• Include display module for indication and
(350mm H x 440mm W x 225mm D) – Oyster Grey
battery test
NPS-11/BBO 11A PSU Stand-alone PSU in 18U/BBO - ONYX Black (610mmx
• Includes fault output relays NPS-11/BBO
443mmx 285mm)
• Certified to AS4428.5

NPS Series Power Supply on Slim Part # Description

line Chassis
NPS-5S 5.6A Stand-alone Power Supply
NPS-11S 11.7A Stand-alone Power Supply
Panel mount 24VDC power supply and
battery charger.
Accessories

• Certified to AS4428.5 Part # Description

• Includes fault output relays
• Replaces PS243 NPS-DISP Display kit to suit NPS power supplies, provides status and battery test switch

NPS Series Power Supply on Wide line Part # Description

Chassis
NPS-5 5.6A Stand-alone Power Supply

Panel mount 24VDC power supply and battery NPS-11 11.7A Stand-alone Power Supply
charger.
Accessories
• Certified to AS4428.5
Part # Description
• Includes fault output relays
• Replaces PS249 NPS-DISP Display kit to suit NPS power supplies, provides status and battery test switch

BATTERIES

Panel Batteries Part # Description

Sealed Lead Acid (SLA) batteries to provide PS1265 SLA Battery 7AH - 151mm (L) x 65mm (W) x 101mm(H)

secondary power supply to equipment. BATT12 SLA Battery 12AH - 151mm(L) x 98mm(W) x 101mm(H)
BATT18 SLA Battery 18AH - 181mm(L) x 77mm(W) x 167mm(H)
• Approved to AS1603.4
BATT22 SLA Battery 22AH - 181mm(L) x 77mm(W) x 167mm(H)

NOTE: 2 x batteries required for 24V system BATT26 SLA Battery 26AH - 175mm(L) x 166mm(W) x 125mm(H)
BATT33 SLA Battery 33AH - 195mm(L) x 130mm(W) x 180mm(H)
BATT40 SLA Battery 40AH - 197mm(L) x 165mm(W) x 170mm(H)
BATT75 SLA Battery 75AH - 258mm(L) x 166mm(W) x 206mm(H)
BATT85 SLA Battery 85AH - 305mm(L) x 168mm(W) x 212mm(H)
BATT100 SLA Battery 100AH - 330mm(L) x 172mm(W) x 221mm(H)
BATT150 SLA Battery 150AH - 485mm(L) x 172mm(W) x 240mm(H)

www.notifier.co.nz 43 Trade Product List 2019

Detector Test & Removal

SOLO TEST KITS

SOLO Smoke Detector Kits Part # Description

Smoke test ‘Starter Pack’ (Contains Solo330 and Solo108) no bag included
SOLO808
Solo ‘Starter Packs’ for use in testing smoke (4m reach)
detectors only. Smoke test ‘Starter Pack’ (Contains Solo330 and Solo100) no bag included
SOLO809
exc bag (6m reach)
Smoke test and removal kit Contains Solo330, Solo100, Solo200 and
SOLO811
Solo610) inc bag (6m reach)

Part # Description
SOLO Smoke & Heat Detector Kits Smoke & Mains Heat detector test and removal kit (Contains Solo330,
SOLO814
Solo424, Solo100, Solo200 and Solo610) (6m reach)
Solo Detector test kits for use in testing
Smoke & Cordless Heat detector test and removal kit (Contains Solo330 ,
smoke & heat detectors. SOLO822
Solo461, Solo100, Solo200 and Solo610) (6m reach)
Smoke & Cordless Heat detector test and removal kit (Contains Solo330,
SOLO823
Solo461, 3x Solo100, Solo200 and Solo610) (9.3m reach)

SOLO Extension Poles Part # Description

Extension pole to suit all SOLO kits SOLO100 4 section telescopic pole (4.5m)
SOLO108 2 section telescopic pole (2.5m)
SOLO101 1 section extension pole (1.13m)

SOLO Tools Part # Description

SOLO200 Universal Detector Removal Tool
Add-on tools for the SOLO kits to add
SOLO330 Aerosol Smoke & CO dispenser
functionality to kits.
Cordless Heat detector tester (incl. 2x Solo760
SOLO461
Battery Batons & 1x Solo726 Battery Charger)
SOLO424 Heat detector tester 240V
SOLO425 SOLO Extension Cable 5metres
SOLO610 SOLO Protective Carrying / Storage Bag

SOLO AEROSOLS

SOLO Aerosols Part # Description

SOLOA5-001 Test Smoke, 250ml can, for hand-held or dispenser use

A range of aerosols for testing and cleaning
a variety of detectors. There are varieties SOLOA10-001 Test Smoke, 150ml can, for hand-helt or dispenser use, Non-Flammable
which are suitable for hand and\or dispenser
SOLOC3-001 Test CO, 250ml can, for hand-held or dispenser use
application

SOLO Smoke Sabre Part # Description

Smoke Sabre is a functional aerosol smoke Smoke detector tester with retractable ‘funnel’,
SMOKESABRE
check for testing smoke detectors quickly and 150ml

cost effectively at a flick-of-the-wrist. Low cost

and simple, it is a revolutionary tester that
eliminates the risk of harmful residue

www.notifier.co.nz 44 Trade Product List 2019

 Detectors Test & Removal

OTHER DETECTOR TEST & REMOVAL EQUIPMENT

Smoke Pens Part # Description

Smoke pens are ideal for testing MASD systems SMOKEPEN Smoke Pen and refills – c/w pk of 6 refills

and smoke detectors. They may also be used in SMOKEPEN-R Smoke Pen refills (pk of 6)
areas of high airflow to determine airflow
direction.

Test Magnets Part # Description

Telescopic test magnet to provide alarm T/MAG System Sensor telescopic test magnet

test on System Sensor conventional and

addressable detectors

System Sensor Detector Removal Tools Part # Description

Removal tools and accessories designed XP-4 Extension poles, 3 x 1.5m poles for XR2(B) kit

specifically for the System Sensor and XR2B Removal tool for 100B/800 series detectors
Notifier range of conventional and
addressable detectors

Digital SPL Meter Part # Description

• Digital readout of the ambient noise level at SPL-METER Digital SPL Meter 35 to 130dB

microphone
• Features low (30-80db) and High (80-130dB)
level
• Frequency range 31.5 - 8,000Hz
• Dynamic range 50dB / Accuracy: +/- 1.4dB
• Two built in weighting curves (A & C
weighting)
• Supplied with carry case, tripod mounting
adaptor and mic wind screen
• requires 1x 9V long life battery (included)
• Dimensions: 252H x 66W x 33D mm

Digital Impedence Meter Part # Description

• Simple user friendly operation Digital Impedance Meter 9V Batt.
IMP-METER
• Suits 70V and 100V up to 10k Watts LCD Display

• Calculates load in ohms and watts

• 9V battery powered with recharging port
• Compact handheld case
• Includes test leads
• Backlit LCD display
• Dimensions: 117H x 79W x 33D mm.

www.notifier.co.nz 45 Trade Product List 2019

Enclosures & Mounting Chassis

MODULE ENCLOSURES

XP Module DGP enclosures Part # Description

DGP enclosure to mount 2 x XP modules
Enclosure for XP multi input/output modules DGP1B
(261mm H x 268mm W x 90mm D)
when being mounted remote from the FACP.
DGP enclosure to mount 4 x XP modules
DGP2B
• APO grey (431mm H x 268mm W x 90mm D)
• Multiple rear, top and bottom knockout cable
entries

Control Panel Enclosures Part # Description

18U Cabinet with window door (887 H x 610 W x 285 D)
• Powder coated ONYX Black texture CAB18U-BK
- ONYX Black
• Includes blank inner door and gear tray
18U Cabinet with solid door (887 H x 610 W x 285 D)
CAB18US-BK
- ONYX Black
28U Cabinet with window door (1330 H x 610 W x 380 D)
CAB28U-BK
- ONYX Black
28U Cabinet with solid door (1330 H x 610 W x 380 D)
CAB28US-BK
- ONYX Black
40U Cabinet with window door (1865 x 610 W x 380 D)
CAB40U-BK
- ONYX Black
40U Cabinet with solid door (1865 x 610 W x 380 D)
CAB40US-BK
- ONYX Black

Battery or Panel Extension Enclosures Description

Part #
ONYX Black – Battery box to suit CAB650 and CAB900
• Powder coated ONYX black texture CAB650BB-BK
(250mm H x 450mm W x 190mm D)
• Knockouts to suit panel enclosure
ONYX Black – Battery box to suit 18U
18UBB-BK
(443mm H x 610mm W x 285mm D)
ONYX Black – Battery box to suit 28U & 40U
28UBB-BK
(443mm H x 610mm W x 380mm D)

Weatherproof Enclosures Part # Description

Surface mount outdoor enclosure in red. WIP-BOX-IP66 Weather proof (IP66) surface mount enclosure
• Ideally suited as WIP handset enclosures
• Thumb turn handle (non locked)

Cabinet Dimensions:
- 300mm H x 200m W x 150mm D

CABINET SURROUNDS

Panel Surrounds Part # Description

CAB650SUR-BK ONYX Black Flush surround to suit CAB 650
Onyx Black texture panel surrounds when CAB900SUR-BK ONYX Black Flush surround to suit CAB900
recessing cabinets into walls etc.
18USUR-BK ONYX Black Flush surround to suit 18U
• Powder coated Onyx Black texture 28USUR-BK ONYX Black Flush surround to suit 28U
• 50mm edging

NOTE: Contact your Notifier systems consultant for alternate (custom) dimensions

www.notifier.co.nz 46 Trade Product List 2019

 Enclosures & Mounting Chassis

MOUNTING CHASSIS & BRACKETS

XP module mounting chassis Part # Description

CHS-2 Mounting chassis for up to 2 x XP modules
The XP module mounting chassis provides a
method for simple installation of addressable Mounting chassis for up to 4 x XP modules
CHS-4
XP modules into a Notifier or 3rd party Designed to allow fitting into CAB650/CAB900
FACP or DGP. Mounting chassis for up to 6 x XP modules
CHS-6
Designed to allow fitting into 18U/28U/40U

Low-Profile mounting chassis Part # Description

CHS-1L Mounting chassis to suit 1 x LCM/ DA-BOWS with Cable Tie Mounts
The low-profile mounting chassis range provides
CHS-2L Mounting chassis to suit 2 x LCM/ DA-BOWS with Cable Tie Mounts
a uniform mounting assembly for almost
CHS-3L Mounting chassis to suit 3 x LCM/ DA-BOWS with Cable Tie Mounts
all Notifier panel modules enabling simple
installation of upgrade modules. CHS-4L Mounting chassis to suit 4 x LCM/ DA-BOWS with Cable Tie Mounts

The chassis is compatible with the following

devices;

- LCM & LEM Loop modules

- Relay modules
- DA Series occupant warning system
- + others

Annunciator Mounting Enclosures Part # Description

ABF-1B Annunciator flush mount box. Mounts 1x annunciator module
A range of mounting enclosures for a
number of annunciators. Available in Annuciator flush mount box with 003 keyed,
ABF-1DB
surface and flush mount versions. tinted Perspex door. Mounts 1 x Annunciator
Annuciator flush mount box with 003 keyed,
ABF-2DB
tinted Perspex door. Mounts 2 x Annunciators
Annuciator flush mount box.
ABF-2B
Mounts 2 x Annunciators or an NCA-2
Annuciator flush mount box with 003 keyed
ABF-4B
tinted Perspex door. Mounts 4 x Annunciators
Annunciator surface box. Mounts 1 x annunciator module. Note: Cannot install
ABS-1B
LCD-80
Annunciator surface mount box with trim.
ABS-1TB
Mounts 1 x Annunciator
Annuciator surface mount box.
ABS-2B
Mounts 2 x Annunciators or an NCA-2
Annuciator surface mount box with 003
ABS-2D
keyed tinted Perspex door. Mounts 2 x Annunciators
Annunciator surface mount box with 003
ABS-4D
keyed tinted Perspex door. Mounts 4 x Annunciators

www.notifier.co.nz 47 Trade Product List 2019

Installation Cable

INSTALLATION CABLE

Fire Rated Installation Cable Part # Description

Twisted 2-hour fire rated installation cable FR-0.75-2C-250 Fire Rated Cable (250m) 2-core x 0.75mm2
FR-0.75-2C-500 Fire Rated Cable (500m) 2-core x 0.75mm2
• AS3103 and ASS008 approved FR-0.75-2CS-250 Fire Rated Cable (250m) 2-core x 0.75mm2, screened
• Easy to strip and terminate
FR-0.75-2CS-500 Fire Rated Cable (500m) 2-core x 0.75mm2, screened
• Screen versions available
FR-1.00-2C-250 Fire Rated Cable (250m) 2-core x 1.00mm2
FR-1.00-2C-500 Fire Rated Cable (500m) 2-core x 1.00mm2
FR-1.50-2C-250 Fire Rated Cable (250m) 2-core x 1.50mm2
FR-1.50-2C-500 Fire Rated Cable (500m) 2-core x 1.50mm2
FR-1.50-2CS-250 Fire Rated Cable (250m) 2-core x 1.5mm2, screened
FR-1.50-2CS-500 Fire Rated Cable (500m) 2-core x 1.5mm2, screened
FR-1.50-2CW-500 Fire Rated Cable (500m) 2-core x 1.50mm2, white stripe
FR-1.50-4C-250 Fire Rated Cable (250m) 4-core x 1.50mm2
FR-2.50-2C-250 Fire Rated Cable (250m) 2-core x 2.5mm2
FR-2.50-2C-500 Fire Rated Cable (500m) 2-core x 2.50mm2

Red TPS Installation Cable Part # Description

• Easy to strip and terminate TPS-0.75-2C-200 TPS Flat Cable (200m) 2-core x 0.75mm2

• Twisted & flat versions available TPS-0.75-2C-500 TPS Flat Cable (500m) 2-core x 0.75mm2
TPS-1.00-2CW-200 TPS Flat Cable (200m) 2-core x 1.00mm2, white stripe
TPS-1.00-2CW-500 TPS Flat Cable (500m) 2-core x 1.00mm2, white stripe
TPS-1.5-2C-200 TPS Flat Cable (200m) 2-core x 1.5mm2
TPS-1.50-2C-500 TPS-Flat Cable (500m) 2-core x 1.50mm2
TPS-1.50-2CW-200 TPS Flat Cable (200m) 2-core x 1.50mm2, white stripe
TPS-1.50-2CW-500 TPS Flat Cable (500m) 2-core x 1.50mm2, white stripe
TPS-1.50-2CT-200 TPS Twisted Cable (200m) 2-core x 1.50mm2, twisted
TPS-1.50-2CT-500 TPS Twisted Cable (500m) 2-core x 1.50mm2, twisted
200 TPS Twisted Screened cable (200m) 2-core x 1.50mm2, twisted &
TPS-1.50-2CTS-200
screened
TPS-1.50-2CTS-500 TPS Twisted Screened cable (500m) 2-core x 1.50mm2, twisted & screened

www.notifier.co.nz 48 Trade Product List 2019

 I.S Barriers & Surge Suppression

INTRINSICALLY SAFE BARRIERS & ISOLATORS

1-chan. Isolation Barrier for use with IS

conventional detectors
Part # Description
Intrinsically safe interface for conventional
detection circuits. KFD0-CS-EX1.56 1-chan. Isol. Barrier for use with IS conventional detectors
• 1-channel isolated barrier
• DC supply (loop powered)
• SMART fire alarm input
• Current output 0 mA ... 40 mA
Group, category, type of protection: Ex II (1)GD, I (M1)
[Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma]
I (-20 °C ≤ Tamb ≤ 60 °C) [circuit(s) in zone 0/1/2]

1-chan. Zener Barrier for use with IS

sounders & strobes Part # Description
Intrinsically safe interface for notification
Z728 1-chan. Zener Barrier for use with IS sounders & strobes
devices such as sounders and beacons.
• 1-channel
• DC version, positive polarity
• Working voltage 26.5 V at 10 μA
• Series resistance max. 327 Ω
• Fuse rating 50mA
• DIN rail mounting
Group, category, type of protection: Ex II (1)GD, I (M1)
[Ex ia Ga]IIC, [Ex ia Da] IIIC, [Ex ia Ma]
I (-20 °C ≤ Tamb ≤ 60 °C) [circuit(s) in zone 0/1/2]

1-chan. Isolation Barrier for use with IS

addressable detectors
Part # Description
Intrinsically safe interface for addressable
KFD0-CS-EX1.54-Y2 1-chan. Isol. Barrier for use with IS addressable detectors
devices and to be used with the IMX-1E
translator module.
• 1-channel isolated barrier See page 13 for Addressable I.S detectors and translator module
• 24 V DC supply (loop powered)
• SMART fire alarm input
• Current input 1 mA ... 20 mA
Group, category, type of protection: Ex II (1)G [Ex ia Ga]
IIC , Ex II (1)D [Ex ia Da] IIIC , Ex I (M1) [Ex ia Ma] I (-20
°C ≤ Tamb ≤ 60 °C)

DX070 Enclosure for intrinsically safe Part # Description

barriers
DX070 Enclosure for IS barriers/isolators
Required to provide mechanical protection
for barriers and isolators

SURGE SUPPRESSION MODULES

Surge Suppression Modules

Part # Description
Surge suppression modules will reduce the risk Group, category, type of protection: Ex II (1)GD, I (M1) [Ex ia Ga] IIC, [Ex
of potential high voltage spikes on power and SURGE-MAINS ia Da] IIIC, [Ex ia Ma] I (-20 °C ≤ Tamb ≤ 60 °C) [circuit(s) in zone 0/1/2]
communication lines. Surge suppression and line filter for 240V mains (10A)
Group, category, type of protection: Ex II (1)G [Ex ia Ga] IIC , Ex II (1)
SURGE-AZF D [Ex ia Da] IIIC , Ex I (M1) [Ex ia Ma] I (-20 °C ≤ Tamb ≤ 60 °C) Surge
suppression for 4 x AZF (conventional zone) circuits
SURGE-SLC Surge Suppression for SLC loop. Protect both A & B channels
SURGE-RS485 Surge suppression for RS485 communications.
Channel Surge suppression for 24V circuits. Can be used for ring power,
SURGE-24V
ancillary power and NACs.

www.notifier.co.nz 49 Trade Product List 2019

Spare Parts

GENERIC

IFS-2008 Gas release termination board

IFS-1125C Supervision module for monitored outputs for connection to relays

PDM Power Distribution Module. 8 x fused outputs, Door Holder Output

WS-FIRE Brigade “FIRE”” label 150mm x 60mm, Red on White

BATT3 SWIFT wireless devices replacement batteries - 3V / CR123A batteries

452 003 Key Lock inc 2 x keys

POWER SUPPLIES

PS24X-DISP Remote display kit for PS24x power supplies

PBC-70 2.6 Amp 24V power supply (non-battery backed

PBC-150 5.6 Amp 24V power supply (non-battery backed

SP-320 11.7 Amp 24V power supply (non-battery backed)

NPS-DISP Display kit for NPS power supplies, provides indication and battery test switch

IFS-2600 SERIES FACP

2600/KEY Keypad membrane for IFS-2600

PSI Power Supply Interface to suit IFS-2600 + AFP-2800 + BC-200

IFS-816 16 zone indication board kit for 2600

CFP-16 SERIES FACP

CFP-16/CPU CPU\Termination Board Replacement for CFP-16

CFP-16/KEY Keypad (AUS) & display for CFP-16

NPS-11CHS NPS-11 Replacement to suit CFP-16/AFP-3030

NPS-5CHS NPS-5 Replacement to suit CFP-16/AFP-3030

PRINTER EQUIPMENT

PRN-80 Panel Printer Kit - includes Thermal Printer, DC-DC converter and metalwork

AM-1010/ AFP-2020 SERIES FACP

LIB-400 Dual loop interface board; supports up to 396 intelligent devices

LIB-200A Loop interface board; supports up to 198 intelligent devices

SIB-2048A Serial interface board for M2.7+ systems;

LCD-80 80 character LCD remote mimic for 1010/2020

MIB-W 1010/2020/INA Twisted pair wire media interface board

DIA-2020AUS Replacement backlit DIA for the 2020

CPU2-1010 Replacement CPU board for the 1010

CPU-2020 Replacement CPU board for the 2020

www.notifier.co.nz 50 Trade Product List 2019

 Spare Parts

AFP-2800 SERIES FACP

LCM-320 Loop Control Module Used as loops 1, 3, 5, 7 or 9

LEM-320 Loop Expander Module Used as loops 2, 4, 6, 8 or 10

KEYPAD/00 Keypad Membrane To suit AFP-2800 Keypad

AFP-2802/CPU CPU and LCD complete for AFP-2802

AFP-2800/CPU CPU and LCD complete for AFP-2800

PSI Power Supply Interface to suit IFS-2600 + AFP-2800

LCD-80/00 80 character LCD remote mimic panel to suit AFP-2800

SCS-8AU/00 Smoke Control Station with 8 x 3 position switches with 3 x LEDs per switch - e.g. AS1668 fan controls

SCS-8L/00 Custom mimic module 24 x inputs + 24 x outputs

ACM-16ATAUS/00 Annunciator Module with 16 Switches, 16 Red/Amber LED's

ACM-32AAUS/00 Annunciator Module with 32 Red LED. E.g. Flow switches, monitors etc.

LDM-32/00 LED Driver card for Graphic Mimic - to suit BC-200/AFP-2800

LDM-R32 Lamp driver relay kit 32 Relays (requires 10460 LDM-32). E.g. Plant & EWIS Interfaces.

NCM-SMOF Network Control Module - Single mode optical fibre

LIM Loop Interface Module (IFS-725I), to suit AFP-2800

NIM Network Interface Module (IFS-725I)

FIM Termination Board, to suit AFP-2800

NCM-W Network Control Module (Wire)

NCM-F Network Control Module - Multi-mode optical fibre

RPT-WF Not-Fire-Net network wire to multi-mode fibre repeater

RPT-W Noti-Fire-Net network wire to wire repeater

HS-NCM-W Network Control Module - Wire

HS-NCM-MF Network Control Module - Multi-mode optical fibre

HS-NCM-SF Network Control Module - Single mode optical fibre

HS-NCM-WMF Network Control Module - Wire/Multi-Mode optical fibre

HS-NCM-WSF Network Control Module - Wire/ Single-mode optical fibre

HS-NCM-MFSF Network Control Module - Multi-Mode/ Single mode optical fibre

USB USB to RS232 Converter, to suit AFP-2800, VESDA. Win7 Compatible

AFP-3030 SERIES PANEL

CPU2-3030AUPLUS CPU2-3030AU CPU Assembly To Suit AFP-3030 (NZ)

NCA-2AUPLUS NCA-2(AU) CPU

DISP-3030NZ Display module for AFP-3030NZ

USB3 USB3 - USB lead 3m, to suit AFP-3030/NCA-2

www.notifier.co.nz 51 Trade Product List 2019

Spare Parts

SOLO TEST EQUIPMENT

SOLO720 SOLO Replacement Battery Baton, for use with the SOLO461 Heat Detector Tester

SOLO725 SOLO BATTERY FAST CHARGER

SOLOSPARE1002 SOLO Plastic caps for SOLO200

SOLOSPARE1005 SOLO Silicon membrane 330/461

SOLOSPARE1028 SOLO Aerosol retaining cup

I-2000 EWIS

CB-MIC CB-style Balanced EWIS Microphone, supplied with mounting clip to suit 10W/25W/50W Evac modules

FA1922 FAB, 1920-5, I2000 Paging Console, Keyboard Overlay

FA2027 I2000 QECP-M3 Membrane K/Board 2 Zone & All Group 3 WIP for use on 21U cabinets

FA2029 I2000 Membrane Keyboard 8 Zones, 3 WIP/Zone for use on 21U cabinets

FP0732 30 zone paging console to suit I-2000

FP1067 I2000 4U Module blank upgrade kit

FP1068 I2000 FIP/BGA Master upgrade kit

FP1069 I2000 FIP/BGA Extender upgrade kit

FP1070 I2000 Strobe Master upgrade kit

FP1071 I2000 SPIF module upgrade kit

FP1072 I2000 ECM module + looms (no software) upgrade kit

FP1073 I2000 WIP Slave + Term.board upgrade kit

FP1074 I2000 100W Amp + transformer upgrade kit

FP1075 I2000 2x 50W Amp + Transformer upgrade kit

FP1076 I2000 2x 25W Amp + transformer upgrade kit

FP1077 I2000 4x 10W Amp + transformer upgrade kit

FP1078 I2000 4x 25W Amp + transformer upgrade kit

FP1079 I2000 200W Amp + transformer upgrade kit

FP1080 I2000 5 module hinge upgrade kit

FP1081 I2000 6 module hinge upgrade kit

FP1082 I2000 7 module hinge upgrade kit

FP1083 I2000 8Z display extender + looms upgrade kit

IC0391 60 Sec Analogue recorder IC to suit EMUX for I-2000

KT0519 200W Amplifier Kit - 2 x AMP cards + wiring loom for I-2000

ME0200 I2000 Cardframe, 699-038

ME0200 Card cage for I-2000

ME0205 Panel 8 Zone Display Extender / 3 WIP Display Keyboard Assembly for use on I2000 (Metalwork, mylar and PCB)

ME0207 Control Panel ECP, 3 WIP/ Zone 699-093 for use on I2000 (Metalwork, mylar and PCB)

ME0213 I2000 Microphone DIN plug for old ECP9002

ME0290 Microphone CB-type to suit I-2000

ME0297 Auto/Manual/Isolate Keyswitch for I2000

ME0330 PS2406 6 Amp 24 Volt Power Supply - Brick

ME0331 PS2406 6 Amp 24 Volt Power Supply 2U Rack Mount

ME0333 PS2412 12 Amp 24Volt Power Supply 2U Rack Mount

ME0381 MECP 2 Zone Mylar and Metalwork only, for I-2000

ME0382 8 Zone Mylar and Metalwork only, for I-2000

www.notifier.co.nz 52 Trade Product List 2019

 Spare Parts

I-2000 EWIS (Continued)

PA0484 Paging Console PCB Assy for I2000, 1929-1

PA0642 WIP Slave, OV Ref Inputs for WIPS2000

PA0643 Evac Control Panel 3WIP/Zone PCB Assy for I2000, ECP9702-2

PA0646 Audio Line Isolation Module for I2000, (DIN) ALIN9706

PA0647 200w Amplifier Card Module for I2000, AMP2009 (Single Amp)

PA0648 200w Transformer Module for I2000, TRAN200

PA0649 Secondary Panel Interface Module for I2000, (DIN) PCB Assy SPIF9709

PA0650 4x10W / 2x25W Amplifier Card for I2000, EAMP9001

PA0651 FIP/BGA Master PCB Assy for I2000, (DIN) FIB8910

PA0652 FIP/BGA Extension PCB Assy for I2000 (DIN) FIPE9004

PA0657 Signal Interface PCB Assy for I2000, (DIN) SE9004

PA0660 Backplane PCB Assy for I2000, BPLN9001

PA0690 2x50W / 1 x 100W Amplifier Card Module PCB Assy for I2000, HAMP9308

PA0691 2x50W Transformer Card Module PCB Assy for I2000, HTRN9308-1

PA0692 1x100W Transformer Card Module PCB Assy for I2000, HTRN9308-2

PA0696 1x100W Transformer Card B495Module Music Switch for I2000, HTMS9408-2

PA0697 Strobe Termination Board PCB Assy for I2000, STRM9502, 8 Strobe/ 16 Relay Module (DIN)

PA0698 Evac Communication Module, PCB Assy for I2000, (DIN) ECM9603

PA0758 Multiplexer 16 sec Speech EMUX9601 for I2000, (replaces PA0654)

PA0759 Multiplexer 60 sec Speech for I2000, EMUX9601

PA0792 4 x 25W Transformer Module for I2000, c/w Relays, TRAN9705-2

PA0794 2 x 25W Transformer Module for I2000, c/w Relays, TRAN9705-4

PA0795 4 x 10W Transformer Module without Relays for I2000, TRAN 9706-1

PA0796 4 x 10W Transformer Module for I2000, c/w Relays, TRAN 9706-2

PA0916 WIP Termination PCB Assy for I2000, (common 0V version) DIN WTRM

SU0168 EWIS Gooseneck Microphone and bracket to suit I-2000 paging console, DM-521 B

SU0169 EWIS Paging Microphone with PTT for I2000 Sw PM600D

VESDA

FIL-FOAM Replace washable filter pads for plastic cont

VSP-000 Blank plate Non-EMC with VESDA logo

VSP-001 Vesda Programmer Module

VSP-002 VLP Display Module Display Module

VSP-003 Vesdanet Socket

VSP-004 Vesda Scanner Display Module

VSP-005 Vesda Filter Assembly to suit VESDA laser plus

VSP-007 Vesda Remote Termination card, no relays

VSP-008 Vesda Remote Termination card with 7 relays

VSP-009 Vesda Scanner Chassis & Complete Manifold Assembly

VSP-012 Vesda Remote Recess mounting kit

VSP-013 Vesda Detector Cover Assembly with EMC shields

VSP-014 Head termination card with 7 relays

VSP-015 Vesda-Spares Detector Aspirator Assembly

VSP-016 Vesda Head termination card with 12 relays

VSP-019 Vesda Filter Cover

VSP-024 Vesda Front cover for VLC-500

VSP-030 Vesda VLI intelligent filter to suit VLI

VSP-031 Vesda VLI secondary filter to suit VLI

www.notifier.co.nz 53 Trade Product List 2019

Spare Parts

VESDA (Continued)

VSP-032 Vesda VLI Replacement Aspirator to suit VLI

VSP-033 Vesda VLI chamber assembly to suit VLI

VSP-034 Vesda VLI VESDAnet Card Spare Part

VSP-036 Vesda VLI US flow manifold Spare

VSP-200 Blank Plate EMC painted, no VESDA logo

VSP-208 Vesda Remote Termination Card with 12 Relays

VSP-300 Blank plate, Non EMC, no vesda logo

VSP-501 Vesda Laser Compact Aspirator spare part only

VSP-502 Vesda Remote Display Compact

VSP-509 VESDAlink RS232 9P-9P Cable Cable for VHH-100 Programmer

VSP-511 VESDANET CABLE HD15 M/F Cable for VHH-100 Programmer

VSP-610 Tamper Proof Sampling Point to suit 25mm conduit

VSP-620 Tamper Proof Sampling Point to suit 8mm capillary tube

VSP-702 Remote Display VLF

VSP-710 VLF-02 Spare Front cover with serv. pan. ASIAN Language Set 1

VSP-715 Aspirator for VLF-500, 2 fan module

VSP-722 Aspirator for VLF-250, 1 fan module

VSP-820 F-BO-AFE70-2 -FAAST Purging Unit

VSP-850-G VESDA In-line filter Grey, 25mm or 1" pipe

VSP-855-20 In-Line Filter (pk20) to suit VSP-850-x

VSP-855-4 In-Line Filter (pk4) to suit VSP-850-x

VSP-860 VSP-860 - Freezer Sampling point to suit aspirated detection

VSP-870 In-line Flow Restrictor Assembly

VSP-871 Flow Restrictor Disc (pack of 10)

VSP-877 Vesda Flush Mount Sampling Point

VSP-890 VESDA VLQ VLQ Surface Mount Kit

VSP-960 Mounting bracket to suit VESDA-E

VSP-962 Filter to suit VESDA-E

VSP-962-20 Filter (20pcs) to suit VESDA-E

VSP-967 VESDA-E VEU-A10 Front Cover 3.5" Display

VSP-980-W VESDA-E VEA 6mm Sampl.Pt Standard Samp.Point- white

VSP-981-W VESDA-E VEA 4mm Sampl.Pt Standard Samp.Point- white

VSP-990 VESDA-E VEA 6mm Microbore Tube UL-compliant Plenum-rated (1000 ft)

VSP-991 VESDA-E VEA 4mm Microbore Tube UL-compliant Plenum-rated (500 ft)

VSP-1001 VESDA-E VEA 6mm to 6mm Straight Union (10pack)

OSID

OSP-001 FTDI Cable 1.5m

OSP-002 Laser Alignment Tool

OSE-RBL Battery Exchange Unit Lithium exchange unit

OSE-RBA OSE-RBA - Emitter Spare Battery Alkaline battery

www.notifier.co.nz 54 Trade Product List 2019

 Information

IECex Hazardous Area Classification:

Zones

Continuous Hazard Intermittent Hazard Possible Hazard

( > 1000hrs/annum) ( >10 < 1000hrs/annum) ( <10 hrs/annum)

EXPLOSIVE GASES Zone 0 Zone 1 Zone 2

DUST Zone 20 Zone 21 Zone 22

In which an explosive gas/dust and air mixture In which an explosive gas/dust and air In which an explosive gas/dust and air
is present continuously or is present for long mixture is likely to occur in the normal mixture is not likely to occur in the normal
periods. operation of the plant. operation.

Type of Protection

Zone Ex Type of Protection

Ex ia Intrinsically-Safe
0 Ex s Special (specially certified)

Ex ma Encapsulation

Any design suitable for Zone 0 plus

Ex d Flameproof

Ex ib/Ex I/EX ID Intrinsically-Safe

1 Ex p/ EX PD Pressurized / continuous dilution

Ex e Increased safety

Ex s Special protection

Ex m/ Ex MD/ Ex mb encapsulated
Any design suitable for Zone 1 plus
Ex n or N Non sparking (Non-incendive)
2 Ex ib Intrinsically-Safe
Ex o Oil immersion
Ex q Powder / sand filled

www.notifier.co.nz 55 Trade Product List 2019

Information

Apparatus Group

Representative Gas Type of Protection Ignitability

Acetylene Group IIC
Hydrogen Group IIC

Easier to ignite
Ethylene Group IIB
Propane Group IIA
Methane Group I

Temperature Class

Classification Temperature (Degrees C) Ignitability

T1 450
T2 300

Easier to ignite
T3 200
T4 135
T5 100
T6 85

Ingress Protection (IP):

FIRST NUMERAL IP SECOND NUMERAL

No Protection 0 0 No Protection

Protection against solid bodies larger than 50mm 1 1 Protected against vertically-falling drops of water or condensation
(e.g accidental contact with the hand)
Protection against solid bodies larger than 12.5mm 2 2 Protection against drops of water falling at up to 15º from the vertical
(e.g finger on the hand)
Protection against solid bodies larger than 2.5mm 3 3 Protection against drops of water falling at up to 60º from the vertical
(e.g tools, wires)
Protection against solid bodies larger than 1 mm 4 4 Protection against drops of water from all directions
(e.g small wires, fine tools)
Protection against dust 5 5 Protection against jets of water from all directions
(no harmful deposits)

Completely protected against dust 6 6 Completely protected against jets of water of similar force to heavy seas

7 Protected against to effects of immersion (defined in minutes)

NEMA Enclosure Types to IEC classification:

NEMA Enclosure Type Number Approximate IP Code

1 IP20
2 IP22
3 IP55
3R IP24
4 IP66
4X IP66
6 IP67
12 IP54
13 IP54

Cabinet Paint Codes:

Colour Dulux Paint Codes

Charcoal Texture #88531
APO Grey #32786
Oyster Grey #36856
Black Texture #32697

www.notifier.co.nz 56 Trade Product List 2019

 Information

Flame Detector Selection Guide:

Dual IR (IR2)

Triple IR (IR3)
Single IR

UV/IR2
UV
Optical Interference Sources

Arc Welding

Modulated IR Radiation

Electrical Sparks

Lightning

Radiation (Nuclear)

Sunlight

Artificial Lighting

UV Lamps

No Effect Some Effect Severe Effect

Smoke
Effects to Sensitivity

Steam

Water Spray

Oil Film

Dust

Minor Reduction Major Reduction

Flame Detector Application Guide:

Single IR Dual IR (IR2) Triple IR (IR3) UV/IR2

Low immunity to false sources High Immunity to false sources Excellent Immunity Highest Immunity
- Lowest Cost to false sources to false sources
- Fastest Response Time (Indoor Areas)
(Indoor or Outdoor Areas) (Indoor or Outdoor Areas)
(For Enclosed & Dark Areas)

Applications Applications Applications Applications

- Agriculture - Churches - Atria - Aircraft Hangars

- Bed Fillings - Coal Handling - Coal Handling - Engine Rooms
- Coal Milling - Fume Cupboards - Nuclear Industry - Engine Test Facilities
- Dryers - Printing - Pharmaceuticals - Generators
- Dust Collection/Filters - Spray Booths - Printing - High Voltage Equip.
- Felt Manufacture - Textiles - Spray Booths - Nuclear Industry
- Wallpaper Production - Waste Handling - Storage Tanks - Power Plants
- Woodworking - Tunnels - Storage Tanks
- Waste Tips

www.notifier.co.nz 57 Trade Product List 2019

Information

Gas Detector Application Guide:

Oil & Gas Chemical Plants Power Stations Waste Water

Treatment Plants

The oil and gas industry covers a Probably one of the largest users Traditionally coal and oil have been Waste Water Treatment Plants are a
large number of upstream activities of gas detection equipment are used as the main fuel for Power familiar site around many cities and
from exploration and production of oil Chemical Plants. They often use a Stations. towns. Sewage naturally gives off
and gas to its transportation, storage wide range of both flammable and In Europe and the US most are both Methane and
and refining. The large amount of toxic gases in their manufacturing being converted to natural gas. H2S. The ‘rotten eggs’ smell of H2S
highly flammable Hydrocarbon gases processes or create them as by- can often be noticed as the nose can
involved are a serious explosive risk products of the processes. Typical Applications: detect it at less than 0.1ppm.
and additionally toxic gases such as • Around the boiler pipe work and
Hydrogen Sulphide are often present. Typical Applications: burners Typical Applications:
• Raw material storage • In and around turbine packages • Digesters
Typical Applications: • Process areas • In coal silos and conveyor belts in • Plant sumps
• Exploration Drilling Rigs • Laboratories older coal/oil fired stations • H2S Scrubbers
• Production Platforms • Pump rows • Pumps
• Onshore oil and gas • Compressor stations Typical Gases:
terminals • Loading Areas Flammable: Typical Gases:
• Refineries Natural Gas, Hydrogen Flammable:
Typical Gases: Toxic: Methane, Solvent
Typical Gases: Flammable: Carbon Monoxide, vapours
Flammable: General Hydrocarbons SOx, NOx and Oxygen Toxic:
Hydrocarbon gases Toxic: deficiency Hydrogen Sulphide,
Toxic: Various including Carbon Dioxide,
Hydrogen Sulphide, Hydrogen Sulphide, Chlorine, Sulphur Dioxide,
Carbon Monoxide Hydrogen Fluoride Ozone.
and Ammonia

Boiler Rooms Hospitals Tumnels / Car Parks

Boiler Rooms come in all shapes and sizes. Small Hospitals may use many different flammable and Car Tunnels and enclosed Car Parks need to be
buildings may have a single boiler whereas larger toxic substances, particularly in their laboratories. monitored for the toxic gases from exhaust fumes.
buildings often have large boiler rooms housing Additionally, many are very large and have onsite Modern tunnels and car parks use this monitoring
several large boilers. utility supplies and backup power stations. to control the ventilation fans.
Tunnels may also need to be monitored for the
Typical Applications: Typical Applications: build up of natural gas.
• Flammable gas leaks from the incoming gas main • Laboratories
• Leaks from the boiler and surrounding gas piping • Refrigeration plants Typical Applications:
• Carbon Monoxide given off badly maintained • Boiler rooms • Car tunnels
boiler. • Underground and
Typical Gases: enclosed car parks
Typical Gases: Flammable: • Access tunnels
Flammable: Methane, Hydrogen • Ventilation control
Methane Toxic:
Toxic: Carbon Monoxide, Typical Gases:
Carbon Monoxide Chlorine, Ammonia, Flammable:
Ethylene oxide and Methane (natural gas),
Oxygen deficiency LPG, LNG, Petrol Vapour.
Toxic:
Carbon Monoxide,
Nitrogen Dioxide

www.notifier.co.nz 58 Trade Product List 2019

 HONEYWELL LIMITED (ACN 000 646 882) trading as ‘Honeywell Security & Fire’
TERMS AND CONDITIONS OF SALE
AUSTRALIA (TBC)

The following terms and conditions apply where Honeywell Limited (ACN 000 646 882) t/a 3.3 Subject to these Conditions, and only in relation to any Services provided by
Honeywell Security & Fire (“HSF”) supplies goods or services to a customer (“Customer”). HSF to a Customer who is not a consumer as defined by the Australian
Consumer Law, HSF hereby expressly warrants that for three (3) months
1. Definitions from date of provision, the Services shall be free from Errors. HSF will if any
For the purpose of these Conditions and unless the context otherwise requires: Errors occur in Services, during the Services Warranty Period, at its election,
“Australian Consumer Law” means the Australian Consumer Law set out in either:
Schedule 2 of the Competition and Consumer Act 2010 (Cth), as supplemented or (a) supply the Services again; or
amended. (b) pay the cost of having the Services supplied again.
“Conditions” means these Terms and Conditions of Sale. 3.4 Clauses 3.1,3.2 and 3.3 will not apply to Errors attributable to:
“Contract” means the contract formed in accordance with clause 2.1, consisting of (a) Non-HSF Goods or Services;
HSF’s proposal (if any), the relevant invoice and these Conditions and where (b) any modification or repair of Goods unless made by HSFor with HSF’s
applicable, Special Conditions of Subcontract relating to the Code and Guidelines. prior written approval;
“Equipment” means equipment manufactured by HSF or its affiliates. (c) negligent use, abuse or misuse of Goods;
“Errors” means the failure of Goods to perform a function as described in the HSF (d) the use of Goods under environmental, power or operating conditions
proposal, the HSF functional specification for those Goods, the appropriate HSF user beyond the limits or constraints specified by HSF;
manual or HSF product literature as the case may be. (e) the installation or wiring of any Goods other than in accordance with
“Goods” means Equipment or Software. HSF’s instructions;
“GST” means the tax imposed by the A New Tax System (Goods & Services) Act (f ) the use of any Goods with any Non-HSF Goods or Services; or
1999 (Cth) and related imposition Acts of the Commonwealth. (g) wear or burn-out resulting from usage of goods of a kind inherently
“Index” means the average weekly earnings measure (as per ABS No. 6302, Series susceptible to burn-out.
No, A594406R [or such other ABS reference as may be substituted for the measure]) 3.5 HSF authorises Customer to pass on the express warranties contained in
or in the event that this Index is discontinued, the Australian Bureau of Statistics clauses 3.2 (a) and (b) (as applicable) to end users who purchase Goods from
index that most reflects the Index’s constituents. Customer, provided that:
“Loss or Damage” includes all types of property, pecuniary or other loss or damage, (a) Customer is not authorised to, and must not purport to, pass on to
including consequential loss or damage and loss of profits. such end-users any warranty rights greater than, or different to, those
“Non-HSF Goods or Services” means equipment, documentation, product literature, granted by HSF in clause 3.2(a) or (b) (as relevant); and
labour, knowledge, service or computer programs in machine readable form that is (b) if Customer wishes to pass on the warranty rights granted in clause
supplied, manufactured, installed or provided by a person other than HSF. 3.2 (a) or (b) in writing, Customer must provide HSF with a copy of
“Person” includes a corporation. the document which it proposes to use for this purpose for review
“Services” means HSF labour or service. and written approval by HSF before such document is provided to the
“Software” means computer programs developed by HSF or its affiliates in the form end-user.
of machine readable instructions and any documentation or product literature relating 3.6 Our Goods come with guarantees that cannot be excluded under the
to those computer programs. Australian Consumer Law. Customer is entitled to a replacement or refund
“System” may include HSF equipment and software and Non-HSF Goods or for a major failure and for compensation for any other reasonably foreseeable
Services. Loss or Damage. Customer is also entitled to have the Goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not
2. Contract Formation amount to a major failure.
2.1 Subject to clause 2.3, a binding agreement will form between the parties: 3.7 This clause 3 states HSF’s total responsibility and liability, and Customer’s
(a) if these Conditions form part of a proposal to Customer, on receipt by sole remedy in respect of the Goods and Services. In no event will HSF be
HSF of Customer’s unconditional acceptance of the proposal, liable for any incidental, consequential, special, or indirect damages, even if
evidenced by Customer’s purchase order whether or not the proposal informed of the possibility of such damages and notwithstanding the failure
is referenced; or of the essential purpose of any limited remedy. No extension of this warranty
(b) otherwise, on HSF’s written acceptance of Customer’s purchase will be binding upon HSF unless set forth in writing and signed by HSF’s
order; and the Contract will constitute the entire contract between authorised representative.
the parties in connection with the sale of Goods and Services.
2.2 Any proposal incorporating these Conditions: 4. Limitation of Liability
(a) will not be valid after 30 days of its date, unless otherwise agreed by 4.1 To the full extent permitted by law and subject to clauses 3.1, 3.2 and 4.2:
HSF; and (a) HSF makes no warranty and will not be liable for any breach of
(b) may be varied or withdrawn by HSF at any time prior to unconditional statutory obligation or implied condition or warranty in respect of
acceptance by Customer. Goods and Services or the materials used, Systems or results of any
2.3 No modifications or variation of the Contract (including any statement by process with which the Goods and Services are used or integrated;
Customer that Customer’s terms will apply) shall bind HSF unless expressly (b) HSF shall under no circumstances be liable in any way whatsoever to
agreed to in writing by an authorised representative of HSF. HSF will not be Customer for any Loss or Damage sustained or incurred by Customer
deemed to have waived these Conditions if it fails to object to provisions or any other party arising directly or indirectly out of the supply of
submitted by Customer. Goods or Services by HSF, the use or performance of Goods or
2.4 These Conditions will prevail in relation to the supply of Goods and Services Services in isolation or as part of a System, any breach by HSF of
to the extent of any inconsistency between these Conditions and any other the Contract, or negligence of HSF. HSF’s liability to the Customer, if
documentation agreed by HSF under clause 2.3. any, in contract, tort or otherwise will be reduced to the extent the
Customer contributed to the Loss or Damage;
3. Express Warranty (c) HSF does not make any representations or give any warranty as to
3.1 Subject to these Conditions, HSF hereby expressly warrants that: the overall performance of any System or the results of any process
(a) Goods manufactured by HSF in its Baulkham Hills, New South Wales with which the Goods or Services are used or integrated; and
facility shall be free from Errors for thirty six (36) months from date of (d) the express warranties in clauses 3.1 and 3.2 is in substitution for all
supply or installation (whichever is the earlier) of the Goods (the other terms, conditions, warranties and representations, implied by
Goods Warranty Period). Any Non-HSF Goods sold by HSF, but not statute or otherwise, and all other terms, conditions, warranties and
manufactured by HSF, will be provided with the same warranty as representations are excluded.
provided by the original manufacturer; and 4.2 Where the Australian Consumer Law imposes statutory consumer
(b) Services performed by HSF shall be free from Errors for twelve (12) guarantees in respect of Services provided by HSF to the Customer, and
months from the date of performance of the Services (Services the Services are of a kind not ordinarily acquired for personal, domestic or
Warranty Period). household use or consumption, then the Customer’s remedies for breach of
3.2 HSF will if any Errors occur in Goods, during the Goods Warranty Period, at any such statutory consumer guarantee shall be limited to, at HSF’s election:
its election, either: (a) re-supply of the Services; or
(a) in the case of Equipment, (b) payment of the cost of having the Services supplied again.
(i) replace the Equipment or supply equivalent equipment FOB at 4.3 This clause 4 will survive termination or completion of the Contract.
HSF’s facility; or
(ii) repair the Equipment; or 5. Price and Terms of Payment
(iii) pay the cost of replacing the Equipment; and 5.1 Unless stated otherwise in writing, all prices quoted by HSF, are exclusive
(b) in the case of Software, of all taxes, (including any GST), duties, levies and any other government
(i) repair, modify or make good the Software; or charges, and where applicable shall be added to the price payable by the
(ii) make available to Customer instructions to enable Customer to Customer to HSF. When GST is payable by HSF in respect of a taxable supply
repair, modify or make good the Software; or made by HSF to the Customer, the Customer shall pay HSF, in addition to

www.notifier.co.nz 59 Trade Product List 2019

 the GST - exclusive price, the amount on account of GST shown in the tax may sell the Goods in the ordinary course of business but must hold
invoice rendered by HSF. all proceeds from any such sale in trust for HSF.
5.2 Unless stated otherwise in writing, all prices quoted by HSF, are based 7.2 Registration of security interest
on the factory or supplier price list as held by HSF at date of proposal and (a) For supplies made in Australia, terms in this clause 7.2 that are
also on rates of duty and primary wages and salaries, freight insurance defined by the Personal Property Securities Act 2009 (PPSA
and exchange rates prevailing at the date of the proposal. Any increase in (Australia) have the same meaning in this clause.
price resulting from variation in any of these factors shall be payable by (b) For supplies made in New Zealand, terms in this clause 7.2 that are
Customer. All prices are quoted based on HSF’s terms and conditions; to defined by the Personal Property Securities Act 1999 (PPSA (NZ))
the extent Customer’s terms and conditions are deemed to apply, HSF have the same meaning in this clause.
reserves the right to modify all prices according to the additional level of (c) The Customer agrees and acknowledges that:
risk and responsibility that Customer’s terms and conditions require HSF to (i) for the purposes of the PPSA, HSF has a security interest in the
undertake. Additionally, thirty (30) days prior to the expiry of the first term of Goods and in all proceeds from disposal of the Goods; and
this Contract or such other time as nominated by HSF and every anniversary (ii) HSF may register its security interest under this clause 7.2
thereafter, HSF may give to the Customer notice in writing that the price including as a purchase money security interest.
of the Goods or Services shall increase. In the absence of such notice, 7.3 Undertakings
prices quoted by HSF shall increase in accordance with the Index or by 5%, (a) The Customer agrees:
whichever is the greater. (i) to the maximum extent permitted by law, to waive any right to
5.3 HSF reserves the right to raise and be paid for progress claim invoices on receive a verification statement under the PPSA in respect of the
the Customer. Progress claim invoices may be raised upon the supply of security interest under this clause 7;
Equipment Services or Software to Customer or to some other place agreed (ii) to do all things HSF considers necessary or desirable to ensure
or upon the completion of agreed benchmarks or other measure as agreed that HSF’s security interest in the Goods is enforceable,
between Customer and HSF. continuously perfected and afforded the highest priority position
(a) where HSF has Goods ready for supply in accordance with a delivery available to HSF;
schedule agreed between HSF and Customer, but Customer is (iii) to indemnify, and on demand reimburse HSF for all expenses
not able to adhere to that delivery schedule, then HSF may invoice incurred in registering a financing statement or financing change
Customer in accordance with that delivery schedule. In the absence statement on the Personal Properties Securities Register or
of an agreed delivery schedule, the current HSF delivery schedule, as releasing any Goods the subject of the security interest; and
provided to Customer, shall be deemed to be the delivery schedule. (iv) to give HSF ten (10) Business Days’ prior written notice of any
(b) Goods paid for by Customer under sub-clause 5.3 will be held for proposed change in the Customer’s name and/or any other
Customer under HSF’s custody, care and control and will be insured change in the Customer’s details (including but not limited to
by HSF for fire and burglary at replacement value. changes in the Customer’s address, facsimile number, email
5.4 Except as otherwise agreed, invoices will be raised by HSF upon the supply address, or business practice) and immediately advise HSF
of Equipment, Services or Software. of any material change in the Customer’s business practices
5.5 Subject to approval of Customer’s credit by HSF, all charges shall be due and of selling or using any of HSF’s products subject to the security
payable and paid by Customer to HSF within thirty (30) days from date of interest which would result in a change in the end products
invoice. Where HSF has not approved Customer’s credit, all charges shall be produced or the nature of proceeds derived from such sales.
due and payable and paid by the Customer to HSF upon delivery of Goods or 7.4 Confidentiality
Services. The parties agree neither party will disclose any information of the kind
5.6 All payments shall be in Australian legal currency. mentioned in section 275(1) of the PPSA (Australia) or section 177 of the
5.7 Any moneys for which an account or invoice has been furnished to PPSA (NZ), unless the Customer or HSF are otherwise required to disclose
Customer, and which remain unpaid for ninety (90) days after the due date such information under the PPSA Australia or PPSA NZ (as applicable).
for payment shall, at HSF’s option, bear interest as from the date upon which
payment is due at the prevailing commercial overdraft rate of HSF’s then 8. Delay
current bank. 8.1 It is contemplated that any Goods or Services to be supplied by HSF will be
supplied during regular working hours on regular working days. If for any
6. Risk and Title reason Customer requests HSF to supply Goods or Services outside regular
6.1 Property and ownership in Equipment will not pass to the Customer but will working hours, any overtime or additional expenses occasioned thereby shall
remain in HSF until the purchase price of the Equipment has been paid in full. be invoiced to and paid by Customer to HSF as part of the purchase price for
6.2 Until property in the Equipment passes to the Customer: such Goods or Services, at HSF’s then current labour rates to customers.
(a) the Customer shall hold the Equipment as fiduciary bailee and agent 8.2 Extra costs incurred by HSF due to cessation of work occasioned by
for HSF; Customer’s instructions or lack of instructions, by interruptions, mistakes,
(b) unless otherwise notified in writing, the Customer is authorised to or work for which HSF is not responsible shall be reimbursed by Customer
sell or use the Equipment in the ordinary course of business; to HSF upon demand. Extra costs incurred by HSF due to occurrences
(c) after giving 48 hours notice to the Customer, HSF shall be entitled to under clause 9 and sub-clause 9.2 in these terms and conditions shall be
enter the Customer’s premises between 9am and 5pm to inspect the reimbursed by Customer to HSF upon demand.
Equipment;
(d) the Equipment shall be stored separately and in a manner to enable 9. Work to be done by others
them to be identified and cross-referenced to particular invoices; 9.1 Without prior written agreement with Customer to the contrary, HSF will
(e) if the Customer sells or uses the Equipment in a manufacturing or not set in place or install equipment or services piping nor carry out any
value added process of its own or a third party, then the Customer electric wiring work, welding or entry into process lines, or building work
shall hold such part of the proceeds of the sale, manufacturing or such as concreting, cutting and making good, or painting. Such work shall be
value added process as relates to the Equipment in trust for HSF. the responsibility of the Customer and at its expense and shall not be the
Such part shall be deemed to equal in dollar terms the amount owing responsibility of HSF.
by the Customer to HSF for these Equipment at the time. 9.2 HSF will not set the cut out or operating points of safety devices unless
6.3 If the Customer: under the supervision and at the sole responsibility of Customer.
(a) fails to make payments for the Equipment on the due date; or 9.3 HSF will not provide lifting machinery, scaffolding, toilets or other site
(b) commences to be wound up or is placed under official management amenities.
or suffers a receiver or manager to be appointed or becomes
insolvent or bankrupt or commits an act of bankruptcy, the Customer 10. Delivery, etc.
will deliver the Equipment to HSF upon demand. In the event the 10.1 Delivery of Goods not agreed to be installed by HSF shall be FOB a HSF
Customer does not comply with a demand within 48 hours of receipt, warehouse or HSF affiliated or office selected by HSF.
HSF shall be entitled to enter upon the Customer’s premises at 10.2 The delivery times made known to Customer are estimates only and HSF
any time to do all things necessary in order to take possession of does not accept any responsibility for delays whether caused by fire, strike,
the Equipment. The Customer will also pay on demand all costs lockout, dispute with workmen, delays caused by suppliers or others, flood,
associated with the exercise of HSF’s rights under this clause. accident, transportation delays, fuel shortage, inability to obtain material,
war, demand or requirement of Government or statutory authorities or any
7. Retention of Title and PPSA other cause beyond its control. In event of any delay, the date or dates for
7.1 Title performance of this contract by HSF shall be extended for a period at least
(a) All Goods supplied in accordance with the terms of this Contract equal to the time lost by reason of the delay or the delays subsequently
or any other agreement between HSF and the Customer remain caused therefrom.
HSF’s property until the Customer has paid in full all moneys that the 10.3 If the Goods or Services ordered by Customer are unable to be supplied to
Customer owes to HSF from time to time. Customer by the scheduled delivery date, HSF will notify Customer and with
(b) If the Customer purchases Goods for re-supply, then the Customer Customer’s consent, HSF may substitute equivalent goods or services in

www.notifier.co.nz 60 Trade Product List 2019

 place of the Goods and Services ordered by Customer, in order to satisfy 15.2 A party claiming that a dispute has arisen must give written notice to the
Customer’s order. other party specifying the nature of the dispute. On receipt by the other party
of the notice, the matter must be referred to the senior management of each
11. Loss of or Damage to Goods party for resolution. If the managers are unable to resolve the dispute within
11.1 To the extent permitted by law and subject to clause 4.1(b), in the case of ten business days, the parties must mediate the dispute under the mediation
Goods not agreed to be installed by HSF, HSF shall not be liable for any loss rules of the Law Society of New South Wales and the President of the Law
of or damage to the same after delivery FOB point of shipment, including any Society or the President’s nominee will select the mediator and determine
Loss or Damage in transit; the mediator’s compensation.
11.2 To the extent permitted by law and subject to clause 4.2, in the case of
Goods agreed to be installed by HSF, HSF shall not be responsible for loss 16. Software Licence
of or damage to goods, after those Goods have been delivered to the site. HSF agrees to grant to Customer a licence to use any Software provided pursuant to
Should any Goods after being delivered and prior to payment by Customer the Contract, upon and subject to the terms and conditions set out in HSF’s standard
be damaged or destroyed in any way whatsoever, other than by the fault of Software License Agreement which Customer shall execute prior to delivery or
HSF, Customer agrees promptly upon demand to pay or reimburse HSF. In installation of such Software.
addition to and apart from any and all other sums due to or to become due
to HSF under these terms and conditions, an amount equal to the Loss or 17. Governing Law
Damage so occasioned. These Conditions are governed by the laws of New South Wales, Australia. Each
party submits to the non-exclusive jurisdiction of the courts of NSW and the courts
12. Claims which hear appeals from those courts.
Goods supplied shall be examined by Customer promptly upon delivery. To the full
extent permitted by law and subject to clauses 3.1, 3.2 and 4.2, no claim will be 18. Indemnity
recognised by HSF unless such claim is reported to HSF within seven (7) days after Customer agrees to indemnify HSF, its employees and agents and each of them
delivery of the Goods to which the claim relates. from and against all Loss or Damage, resulting directly or indirectly from any acts,
errors or omissions of Customer in connection with the Contract or the use,
13. Return of Goods possession, operation of the Goods or Services. This clause will survive termination
13.1 Subject to clauses 13.2 and 13.3, Goods may be returned for credit if they or completion of the Contract.
do not correspond with the description under which they were sold.
13.2 No Goods may be returned for credit unless HSF’s written approval has been 19. Intellectual Property
first obtained and the original invoice number and date have been quoted for Subject to clause 16, nothing in these Conditions shall confer on Customer any
reference. licence, right, title or interest in or to any intellectual property comprised in
13.3 Only Goods of current design in original sealed cartons, will be considered the Goods or Services, which will at all times remain the property of HSF or
for credit, and a handling charge will be levied by HSF and paid by Customer its suppliers.
to cover necessary inspection, adjustment, repacking and clerical work.
Goods invoiced more than three (3) months prior to attempted return, Goods
which are special in any nature whatsoever, software wirings and tubing cut
to length and goods bought in to special order may not be returned.

14. Variations
Subject to its statutory obligations in relation to the supply of services under the
Australian Consumer Law, HSF reserves the right to revise at any time the extent or
type of goods or services it supplies to the Customer, if it believes that other goods
or services supplied by HSF can fulfil the same function.

15. Dispute Resolution

15.1 The parties agree that if a dispute arises out of or relates to the Contract, a
party may not commence any court or arbitration proceedings relating to the
dispute unless it has complied with the provisions of this clause 15, except
to seek urgent interlocutory relief.

www.notifier.co.nz 61 Trade Product List 2019

Index

1 BEXCP3A-BG-LF 31
FDM-1
FDMR-1
18
18
BEXCS110-L2D 23 Fibre Optic Linear Heat Detection 35
1668x2 4
BEXL15D100V 23 FIM 48
18U 43
BExS110D24DC 26 Fire Rated Cable 47
18U/BB 43
BExS120D24DC 26 FirstVision 9

2 Blue MCP 30 Flame Detector

Flame simulator
33
33

2012/24AUS 11
C Flashni 24
Flush surrounds for panels 43
2012J 11
CAB650BB-BK 43 FMM-1 18
2151BAUS 11
Capillary tube 40 FMM-101 18
28U 43
Ceiling Speaker 23 FRM-1 18
28U/BB 43
Centaur Bracket 44 FSB-200 15

4 CFP-16
CHS-1L
3
44
FSB-200S
FSP-851AUS
15
15
CHS-2 44 FSP-851AUS/BCK 15
40U 43
CHS-2L 44 FSL-751 15

5 CHS-3L
CHS-4
44
44
FSP-851AUS
FST-851AUS
15
15
CHS-4L 44 FST-851HAUS 15
5151AUS 11
CHS-6 44 FST-851RAUS 15
5151HAUS 11
CMM-2 22 FST-851R-WP 15
5151HRAUS 11
Code Red Bracket 44 FST-851-WP 15
5151RAUS 11
CPU (spare parts) 49 - 52 FZM-1 18

8 D G
885WP-B 11
D2 Duct Detector 12 Gas card See Agent Release Module

A D4120W
DA-120
12
22
Gas Detectors
Graphics
34
See OnyxWorks, See OnyxWorks
DA-120/CAB 22 Green MCP 30
AAM 18
DA-30 22
ABF-1B
ABF-1DB
44
44
DA-30CAB 22 H
DA-60 22
ABF-2B 44
DA-60CAB 22 HASP 40
ABF-2DB 44
DAA2-5070E 21 Horn Speaker 23, 24
ABF-4B 44
DA-DISPA 22 HS-NCM-MF 8
ABS-1B 44
DA-DISPB 22 HS-NCM-MFSF 8
ABS-1TB 44
DA-DISPC 22 HS-NCM-SF 8
ABS-2B 44
DA-DISPD 22 HS-NCM-W 8
ABS-2D 44
DBS-4-W 25 HS-NCM-WMF 8
ABS-4D 44
DBSLIDW 25 HS-NCM-WSF 8
ACM-16ATAUS/00 48
Detector guards 17
ACM-32AAUS/00
ACM-8RA
48
3
DGP1B 43 I
DGP2B 43
Agent Release Module 26
Digital Audio Amplifiers 21 IDX-1E 13
Almos Bracket 44
Digital Voice Command 21 IFS-1125C 49
Annunciator Enclosures 44
DNR-AUS 17 IFS-2004C 49
ASE bracket 44
DNRW 17 IFS-713 See CPU, See CPU
DS-FM 21 IFS-717E See RLY8
B DS-SFM 21 IFS-724 See FIM
DST1.5 12, 17 IFS-725I 48
B401 11 DST10 12, 17 IFS-816 49
B501AUS-BK 15 DST3 12, 17 IFS-993F 4
B501AUS 15 DST5 12, 17 IMX-1E 13
B501AUS-W 15 Dual strobe 4, 24 IR2 Flame Detector 33
BACNET-GW 10 Duct detector (addressable) 17 IR3 Flame Detector 33
Batteries 42 Duct detectors (conventional) 12 IS Horn Sounder 25
Battery box 43 DVC-AOI 21 Isolation Barrier 48
BCK-200B/10 15 DVC-EM 21 IS-A105N-R 25
BDA-70V 21 DX070 48 IS-L101L 25
BEAM1224 12 IS-mA1-R 25
BEAM1224S 12 E IS-mB1 25
BEAMLRK 12, 15 IS-mC1-R/R 25
BEAMMK 12, 15 End cap (ASD pipe) 40 ISO-X 18
BEAMSMK 12, 15 ETX 12, 17
Bells 25 E60 - E240 12 J
BEXBG05D24DC-RD 24
BEXBG15D24DC-RD 24 F J piece 40

Face plates for Warning signs 29 K

FAPT-851AUS 15
FCM-1 18 KFD0-CS-Ex1.56 48

www.notifier.co.nz 62 Trade Product List 2019

 Index

KFD0-CS-Ex1.54-Y2 48 U
P
L UniPoint Gas detector Controllers 34
Paging Console 22 Upload/Download cable 48
LaserCOMPACT 37 PBC-150 49 USB to RS232 Converter 48
LaserFOCUS 37 PBC-70 49 UV/IR Flame detector 33
LaserSCANNER 38 Pendant Speaker 24
LCD-80/2800 48 Pipe clip 40 V
LCM-320 5, 48 Pipe junction 40
LCS 24 Pressure switch 19 VESDA/ASD Pipe 40
LDM-32 7 Projection Speaker 24
LDM-R32 7 PS200 30, 31
LEM-320 5, 48 PS210 30, 31 W
LIM 48
Linear Heat Detection
Loop Control Module
35, 36
See LCM-320
R Warning sign face plate 29
White detector cover 15
Loop Expander Module See LEM-320 White MCP 30
Relay modules 3, 4, 44
Low profile chassis 44 WIP Handset 20
Remote indicator 17
WIP/BOX/IP66 20, 43
M Repeater
Resettable MCP
See RPT-F or RPT-WF
30 WSA-I/SI 29
Romteck Bracket 44 WSA-O/SI 29
M200E-DIN 18 WSR-I 29
Roshni 24
M200E-PMB 18 WSR-O 29
RPT-W 8
M200E-SMB-KO 18
RPT-WF 8
Magnetic Door Holders
MCP clear flap
32
30
RTS451Key 12 X
MDH/F
MDH1000
32
32
S XCD Gas Detector 34
XP module mounting 44
MDH1350 32
Sampling point 40 XP-10M 19
MDH400 32
SC070 30, 31 XP-4 44
MDHREM 32
SCS-8A 6 XP-6C 19
MDHW15 32
SCS-8LA 6 XP-6MA 19
MDHW30 32
SDM-4 22 XP-6R 19
MHRZA 25
SDX-851AUS 13
MHWZA 25
MIC/1D 22
Sensepoint XCD
SG-1x10
34
30, 31
Y
MIC/4D 22
Small bend 40
Mimic (LCD) See LCD-80 Y piece 40
SMB-500 18
Mini-Horn Sounder 25 Yellow MCP 30
SMK-400 11, 15
ModBus-GW-3 10
Smoke alarm See 2012
Z
N Smoke Pen
SMOKE-C
44
43
Zener barrier 48
SMOKE-CO 43
NCM-F 8 Z728 48
SMOKE-D 43
NCM-SF 8
SMOKE-S 43
NCM-W 8
SMOKESABRE 43
NFN-GW-AU-EM-3 10
SMOKE-T 43
NFN-GW-PC-F 9
SOLEX10 25
NFN-GW-PC-W 9
SOLO 43
NFS2 49
SP-125 23
NFS4 49
SP-320 49
NFS8 49
Speakers 24, 25
NIM 48
SpectrAlert 24
Notify-IP 9
SPH-15W 23
NPS-11 42, 49
SRHKRLFIRE 24
NPS-11/BBO 42
SSM Series Fire Bells 25
NPS-11S 42
STI-3150 24
NPS-2/BB 42
STI-9604 17
NPS-5 42, 49
Surge Suppression 48
NPS-5BB 42
Surrounds 43
NPS-5S 42
NPS-DISP
NTFast bracket
42, 49
44
T
NWS-3 10
T piece 40

O Test magnet
TPS Cable
44
47
Trunk adaptor 40
Onyx FirstVision 9
Type E Probe 12
OnyxWorks 9

www.notifier.co.nz 63 Trade Product List 2019

For over 60 years, NOTIFIER has been a leader
in the fire alarm industry.
Today, we are the largest
manufacturer of engineered fire alarm systems
with over 400 distributors worldwide,
and regional support operations on every continent
for the flexibility and options your business needs.
NOTIFIER – Fully Connected, Fully Protected.

Honeywell Security & Fire (Pacific) Honeywell Security & Fire (NZ)
Honeywell Ltd Honeywell Ltd
9 Columbia Way 56 Cawley St Ellerslie
Norwest Business Park AUCKLAND, NZ 1051
BAULKHAM HILLS NSW 2153 Visit: www.notifier.co.nz
Visit: www.notifier.com.au
Tel: +64 9 623 5050 (New Zealand)
Tel: 1300 234 234 (Australia) Email: [email protected]

DOC-02-183 – REV. A

informationguide2019

www.notifier.co.nz 64 Trade Product List 2019