bloc fix PLASTERING
MORTARS
Mounting and gap filling mortar for hollow blocks and bricks
PRODUCT
bloc fix is a ready mix mortar that requires only the
addition of water. It is made of cement, graded sand and
additives for improved workability, better bonding and water
retention.
bloc fix is particularly adapted for mounting
regular/hollow blocks, stones, and bricks and to fill gaps
between concrete and bricks.
CHARACTERISTICS
Composition Cement, graded sand,
additives
Appearance Grey powder
Mix Density 1.9 kg/Lt ± 0.1
Grain size Up to 4mm
Thickness after laying the 1 to 2 cm
bloc PACKAGING
Pull off strength at 28 days > 0.3 MPa Leb Syria Jordan UAE Qatar Kuwait KSA Oman
(BS 1881 part 207) 50 kg 50 kg 50 kg 50 kg 50 kg 50 kg 50 kg 50 kg
Compressive strength 13 MPa at 28 days
ASTM C 109
VOC, method USEPA 24 < 1 g/LT
Resistance to fire as per BS Class A1
EN 998 -2, 2003 CURING
Protect the newly applied material from sunshine and wind.
INSTRUCTIONS FOR USE The new material has to be cured with water for at least
SURFACE PREPARATION three days by spraying 3 to 4 times daily.
The surface should be clean, sound and free from any
powder or greasy matter. It must not be over-heated not YIELD
frozen. 1000 kg of bloc fix with 12 % of clean cool water will give
In hot weather, the surface receiving bloc fix should be around 550 liters of workable mortar.
brushed with some water immediately prior to the application. A 50 kg bag = 27 liters approx. of fresh mortar.
PRODUCT PREPARATION STORAGE
Using a low speed mixer, mix 50 kg bloc fix with 5 to 6 12 months after manufacturing date in original and non-open
liters of clean cool water to obtain a homogeneous paste. packaging , under cover, in dry condition, away from humidity,
If necessary, Adjust consistency by adding water without protected from extreme temperatures and direct sunlight.
excess.
For Lebanon , mix 50 Kg bloc fix with 5 to 6 liters of
SAFETY PRECAUTIONS
clean cool water to obtain a homogeneous paste.
The product contains cement powders which, when mixed
with water, release alkalis that could be harmful to the skin. It
PRODUCT APPLICATION
is preferable that the application be done in a ventilated
Apply weber.bloc fix on the blocks using a trowel.
area, and to wear protective gear for hands, eyes and
Place the blocks onto the mortar ensuring good contact.
respiratory system and to avoid breathing of the dust.
Check the level and continue with the next block.
Splashes on the skin should be washed away by cleaning
Remove excess material with a wet sponge before setting.
with soap and water. In case of contact with eyes, wash
Ideal application temperature is between + 5ºC and + 35ºC.
thoroughly with clean water . If swallowed, do not induce
vomiting in both cases seek medical attention. The product
is non-flammable.
1/2 Technical data sheet . Edition: 02.21-A www.middleeast.weber
bloc fix PLASTERING
MORTARS
DISCLAIMER
While the company guarantees its products against defective
materials, the use and application of these products are
made without guarantee since the conditions of their application
are beyond its control. It is recommended to verify with the
company that the product is suitable for the intended use,
and that this Data Sheet version is the latest one. The company
may modify it without prior notice. Technical characteristics
are listed for guidance only. For more information, please
contact the company’s office in your location.
NOTE
The information included on this Technical Data Sheet is the
sole property of Saint-Gobain Middle East Holding SAL (previously
SODAMCO Holding). The unauthorized disclosure, use,
dissemination or copying (either whole or partial) of this
data sheet or any information it contains, is prohibited and
subject to legal pursuit.
2/2 Technical data sheet . Edition: 02.21-A www.middleeast.weber
