0% found this document useful (0 votes)

28 views248 pages

Eastgrove (Deiled11) Final

The document outlines the structural analysis and design criteria for a proposed three-storey commercial building with a roof deck in Bacolod City, Negros Occidental, owned by Alenco Iloilo Realty Corp. It includes specifications for materials, load calculations, and compliance with various structural codes, detailing parameters for dead loads, live loads, earthquake loads, and wind loads. The analysis employs advanced modeling software to ensure structural integrity under specified conditions.

Uploaded by

Royce John Bañas

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

28 views248 pages

Eastgrove (Deiled11) Final

Uploaded by

Royce John Bañas

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 248

STRUCTURAL ANALYSIS

AND

DESIGN FOR THE PROPOSED

THREE(3)-STOREY

COMMERCIAL BUILDING WITH

ROOFDECK
PROJECT: THREE (3)- STOREY COMMERCIAL BUILDING WITH ROOFDECK
OWNER: ALLENCO ILOILO REALTY CORP.
LOCATION: BACOLOD CITY, NEGROS OCCIDENTAL

DESIGN CRITERIA

CODES:

1. NATIONAL STRUCTURAL CODE OF THE PHILIPPINES 7TH EDITION (NSCP C101-15) 2ND
PRINTING 2019
2. UNIFORM BUILDING CODE (UBC1997)
3. AMERICAN CONCRETE INSTITUTE (ACI 318M-2014)
4. AMERICAN SOCIETY OF CIVIL ENGINEERS (ASCE 7-2016)
5. AMERICAN INSTITUTE OF STEEL CONSTRUCTION (AISC 360-16)

COMPRESSIVE STRENGTH OF CONCRETE FOR ALL STRUCTURAL MEMBERS : 21 MPa

YIELD STRENGTH OF REINFORCING STEEL FOR ALL R. C. MEMBERS : 276 MPa (INTERMEDIATE
GRADE)
STRUCTURAL STEEL : A36 ROLLED SHAPES (36,000psi)
SOIL BEARING CAPACITY : Borehole 1 @4.5m = 90 kN/m2, Borehole 3 @4.5m = 427 kN/m2

_________________________________
Civil Engineer
PRC NO._____________
PTR NO._____________
ISSUED AT___________
ISSUED ON___________
PROPERTY REDUCTION FACTORS: FROM TABLE 406.6.3.1.1(a), NSCP C101-15 2ND PRINTING

FOR CONCRETE COLUMNS = 0.70 x GROSS MOMENT OF INERTIA

FOR CONCRETE BEAMS = 0.35 x GROSS MOMENT OF INERTIA

DEAD LOADS

SELF-WEIGHT

ROOF DLS
CEILING + MECH, ELECTL, PLUMBING = 0.25 KN/SQM
ROOFING SHEET = 0.05 KN/SQM
PURLINS = 0.2 KN/SQM
TOTAL ROOF DL = 0.5 KN/SQM
2ND TO 3RD FLOOR DLS
WT OF RC SLAB (0.125M THK) = 3.5 KN/SQM
CHB WALL = 3.5 KN/M ON AFFECTED BEAMS

LIVE LOADS

COMMERCIAL LIVE LOAD = 2.4 KN/SQM

ROOF LIVE LOAD = 0.6 KN/SQM

EARTHQUAKE LOAD PARAMETERS

ZONE 4
IMPORTANCE FACTOR 1
RWX 8.0
RWY 8.0
SOIL TYPE SD
CT 0.0853
NEAR SOURCE FACTOR 1
NV 1

WIND LOAD PARAMETERS

CODE: ASCE 7-2016

CATEGORY IV
BASIC WIND SPEED = 250 KPH
EXPOSURE B
midas Gen WIND LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.wpf

WIND LOADS BASED ON IBC2012(ASCE7-10) (Directional Procedure) [UNIT: kN, m]

__________________________________________________________________________

Design Wind Loads : F = p * Area

Design Wind Pressure : p = qz*G*Cp1 - qh*G*Cp2
Velocity Pressure at Design Height z [psf] : qz = 0.00256*Kz*Kzt*Kd*V^2
Velocity Pressure at Mean Roof Height [psf] : qh = 0.00256*Kh*Kht*Kd*V^2
Calculated Value of qh for X-dir [psf] : qh = 64.76
Calculated Value of qh for Y-dir [psf] : qh = 64.76

Basic Wind Speed [mph] : V = 155.00

Directional Factor for X-dir Wind Loads : Kdx = 0.85
Directional Factor for Y-dir Wind Loads : Kdy = 0.85
Exposure Category : D
Mean Roof Height : H = 43.31
Gradient Height [ft] : Zg = 700.00
Power Law Exponent : Alpha= 11.50
Kz at Mean Roof Height (Kh) : Kh = 1.24

Structural Rigidity : Rigid Structure

Gust effect Factor for X-dir Wind Loads : Gx = 0.85

Gust effect Factor for Y-dir Wind Loads : Gy = 0.85

Topographic Effects for X-dir Wind Loads : Not Included

Topographic Effects for Y-dir Wind Loads : Not Included
Accidental Eccentricity for X-direction : Wx = None
Accidental Eccentricity for Y-direction : Wy = None
Scale Factor for X-directional Wind Loads : SFx = 1.00
Scale Factor for Y-directional Wind Loads : SFy = 0.00

-----------------------------------------------------------------------------------------------

Wind force of the specific story is calculated as the sum of the forces
of the following two parts.
1. Part I : Lower half part of the specific story
2. Part II : Upper half part of the just below story of the specific story

The reference height for the calculation of the wind pressure related factors are,
therefore, considered separately for the above mentioned two parts as follows.

Reference height for the wind pressure related factors(except topographic related factors)
1. Part I : top level of the specific story
2. Part II : top level of the just below story of the specific story

Reference height for the topographic related factors :

1. Part I : bottom level of the specific story
2. Part II : bottom level of the just below story of the specific story

-----------------------------------------------------------------------------------------------

** External Pressure Coefficients at Windward and Leeward Walls (Cp1, Cp2)

STORY Cp1 Cp2(X-DIR) Cp2(Y-DIR)

NAME (Windward) (Leeward) (Leeward)
---------- ----------- ----------- -----------
Roof 0.800 -0.500 -0.298
4F 0.800 -0.500 -0.298
3F 0.800 -0.500 -0.298
2F 0.800 -0.500 -0.298
1F 0.800 -0.500 -0.298
B 0.000 0.000 0.000
----------------------------------------------

** Velocity Exposure Coefficients at Design Height (Kz)

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:47
http://www.MidasUser.com
Gen 2021 -1/5-
midas Gen WIND LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.wpf

** Topographic Factors at Windward and Leeward Walls (Kzt)

** Velocity Pressure at Design Height (qz) [Current Unit]
STORY Kz Kzt(X-DIR) Kzt(Y-DIR) Kzt(X-DIR) Kzt(Y-DIR) qz(X-DIR) qz(Y-DI
R)
NAME (Windward) (Windward) (Leeward) (Leeward)
---------- ----------- ----------- ----------- ----------- ----------- ----------- ---------
--
Roof 1.275 1.000 1.000 1.000 1.000 3.192 3.1
92
4F 1.275 1.000 1.000 1.000 1.000 3.192 3.1
92
3F 1.258 1.000 1.000 1.000 1.000 3.148 3.1
48
2F 1.185 1.000 1.000 1.000 1.000 2.965 2.9
65
1F 1.080 1.000 1.000 1.000 1.000 2.703 2.7
03
B 0.000 0.000 0.000 0.000 0.000 0.000 0.0
00
--------------------------------------------------------------------------------------------
--

W I N D L O A D G E N E R A T I O N D A T A X - D I R E C T I O N

STORY NAME PRESSURE ELEV. LOADED LOADED WIND ADDED STORY STORY OVERTURN
`G
HEIGHT BREADTH FORCE FORCE FORCE SHEAR MOMENT
---------- -------- ------- ------- ------- ---------- ---------- ---------- ---------- --------
--
Roof 3.488533 15.6 0.6 81.8 171.2172 0.0 171.2172 0.0 0
.0
4F 3.488533 14.4 2.7 81.8 765.32265 0.0 765.32265 171.2172 205.460
64
3F 3.458525 10.2 4.2 81.8 1166.8057 0.0 1166.8057 936.53985 4138.9
28
2F 3.333917 6.0 5.1 81.8 1347.2301 0.0 1347.2301 2103.3456 12972.9
79
G.L. 3.156193 0.0 3.0 81.8 774.52985 0.0 -- 3450.5757 33676.4
34
------------------------------------------------------------------------------------------------
--

W I N D L O A D G E N E R A T I O N D A T A Y - D I R E C T I O N

STORY NAME PRESSURE ELEV. LOADED LOADED WIND ADDED STORY STORY OVERTURN
`G
HEIGHT BREADTH FORCE FORCE FORCE SHEAR MOMENT
---------- -------- ------- ------- ------- ---------- ---------- ---------- ---------- --------
--
Roof 2.956415 15.6 0.6 40.141 71.204064 0.0 0.0 0.0 0
.0
4F 2.956415 14.4 2.7 40.141 317.88875 0.0 0.0 0.0 0
.0
3F 2.926407 10.2 4.2 40.141 482.8654 0.0 0.0 0.0 0
.0
2F 2.801799 6.0 5.1 40.141 552.17971 0.0 0.0 0.0 0
.0
G.L. 2.624075 0.0 3.0 40.141 315.99899 0.0 -- 0.0 0
.0
------------------------------------------------------------------------------------------------
--

W I N D L O A D G E N E R A T I O N D A T A RZ - D I R E C T I O N

STORY NAME TORSIONAL ELEV. LOADED LOADED WIND ADDED STORY ACCUMULATED
PRESSURE HEIGHT BREADTH TORSION TORSION TORSION TORSION

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:47
http://www.MidasUser.com
Gen 2021 -2/5-
midas Gen WIND LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.wpf

---------- --------- ------- ------- ------- ---------- ---------- ---------- -----------

Roof 0.0 15.6 0.6 81.8 0.0 0.0 0.0 0.0
4F 0.0 14.4 2.7 81.8 0.0 0.0 0.0 0.0
3F 0.0 10.2 4.2 81.8 0.0 0.0 0.0 0.0
2F 0.0 6.0 5.1 81.8 0.0 0.0 0.0 0.0
G.L. 0.0 0.0 3.0 81.8 0.0 0.0 -- 0.0
-----------------------------------------------------------------------------------------

===========================
ECCENTRICITY RELATED DATA
===========================

STORY STORY STORY ACCIDENTAL ACCIDENTAL ACCIDENTAL ACCIDENTAL

NAME FORCE(X) FORCE(Y) ECCENT.(X) ECCENT.(Y) TORSION(X) TORSION(Y)
---------- ---------- ---------- ---------- ---------- ---------- ----------
Roof 171.2172 0.0 0.0 0.0 0.0 0.0
4F 765.32265 0.0 0.0 0.0 0.0 0.0
3F 1166.8057 0.0 0.0 0.0 0.0 0.0
2F 1347.2301 0.0 0.0 0.0 0.0 0.0
G.L. -- -- 0.0 0.0 -- --

WIND LOADS BASED ON IBC2012(ASCE7-10) (Directional Procedure) [UNIT: kN, m]

__________________________________________________________________________

Design Wind Loads : F = p * Area

Basic Wind Speed [mph] : V = 155.00

Structural Rigidity : Rigid Structure

Gust effect Factor for X-dir Wind Loads : Gx = 0.85

Gust effect Factor for Y-dir Wind Loads : Gy = 0.85

Topographic Effects for X-dir Wind Loads : Not Included

Topographic Effects for Y-dir Wind Loads : Not Included
Accidental Eccentricity for X-direction : Wx = None
Accidental Eccentricity for Y-direction : Wy = None
Scale Factor for X-directional Wind Loads : SFx = 0.00
Scale Factor for Y-directional Wind Loads : SFy = 1.00

-----------------------------------------------------------------------------------------------

The reference height for the calculation of the wind pressure related factors are,
therefore, considered separately for the above mentioned two parts as follows.

Reference height for the topographic related factors :

1. Part I : bottom level of the specific story
2. Part II : bottom level of the just below story of the specific story

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:47
http://www.MidasUser.com
Gen 2021 -3/5-
midas Gen WIND LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.wpf

-----------------------------------------------------------------------------------------------

** External Pressure Coefficients at Windward and Leeward Walls (Cp1, Cp2)

STORY Cp1 Cp2(X-DIR) Cp2(Y-DIR)

** Velocity Exposure Coefficients at Design Height (Kz)

** Topographic Factors at Windward and Leeward Walls (Kzt)
** Velocity Pressure at Design Height (qz) [Current Unit]
STORY Kz Kzt(X-DIR) Kzt(Y-DIR) Kzt(X-DIR) Kzt(Y-DIR) qz(X-DIR) qz(Y-DI
R)
NAME (Windward) (Windward) (Leeward) (Leeward)
---------- ----------- ----------- ----------- ----------- ----------- ----------- ---------
--
Roof 1.275 1.000 1.000 1.000 1.000 3.192 3.1
92
4F 1.275 1.000 1.000 1.000 1.000 3.192 3.1
92
3F 1.258 1.000 1.000 1.000 1.000 3.148 3.1
48
2F 1.185 1.000 1.000 1.000 1.000 2.965 2.9
65
1F 1.080 1.000 1.000 1.000 1.000 2.703 2.7
03
B 0.000 0.000 0.000 0.000 0.000 0.000 0.0
00
--------------------------------------------------------------------------------------------
--

W I N D L O A D G E N E R A T I O N D A T A X - D I R E C T I O N

STORY NAME PRESSURE ELEV. LOADED LOADED WIND ADDED STORY STORY OVERTURN
`G
HEIGHT BREADTH FORCE FORCE FORCE SHEAR MOMENT
---------- -------- ------- ------- ------- ---------- ---------- ---------- ---------- --------
--
Roof 3.488533 15.6 0.6 81.8 171.2172 0.0 0.0 0.0 0
.0
4F 3.488533 14.4 2.7 81.8 765.32265 0.0 0.0 0.0 0
.0
3F 3.458525 10.2 4.2 81.8 1166.8057 0.0 0.0 0.0 0
.0
2F 3.333917 6.0 5.1 81.8 1347.2301 0.0 0.0 0.0 0
.0
G.L. 3.156193 0.0 3.0 81.8 774.52985 0.0 -- 0.0 0
.0
------------------------------------------------------------------------------------------------
--

W I N D L O A D G E N E R A T I O N D A T A Y - D I R E C T I O N

STORY NAME PRESSURE ELEV. LOADED LOADED WIND ADDED STORY STORY OVERTURN
`G
HEIGHT BREADTH FORCE FORCE FORCE SHEAR MOMENT

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:47
http://www.MidasUser.com
Gen 2021 -4/5-
midas Gen WIND LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.wpf

---------- -------- ------- ------- ------- ---------- ---------- ---------- ---------- --------
--
Roof 2.956415 15.6 0.6 40.141 71.204064 0.0 71.204064 0.0 0
.0
4F 2.956415 14.4 2.7 40.141 317.88875 0.0 317.88875 71.204064 85.4448
77
3F 2.926407 10.2 4.2 40.141 482.8654 0.0 482.8654 389.09282 1719.63
47
2F 2.801799 6.0 5.1 40.141 552.17971 0.0 552.17971 871.95822 5381.85
92
G.L. 2.624075 0.0 3.0 40.141 315.99899 0.0 -- 1424.1379 13926.6
87
------------------------------------------------------------------------------------------------
--

W I N D L O A D G E N E R A T I O N D A T A RZ - D I R E C T I O N

STORY NAME TORSIONAL ELEV. LOADED LOADED WIND ADDED STORY ACCUMULATED
PRESSURE HEIGHT BREADTH TORSION TORSION TORSION TORSION
---------- --------- ------- ------- ------- ---------- ---------- ---------- -----------
Roof 0.0 15.6 0.6 81.8 0.0 0.0 0.0 0.0
4F 0.0 14.4 2.7 81.8 0.0 0.0 0.0 0.0
3F 0.0 10.2 4.2 81.8 0.0 0.0 0.0 0.0
2F 0.0 6.0 5.1 81.8 0.0 0.0 0.0 0.0
G.L. 0.0 0.0 3.0 81.8 0.0 0.0 -- 0.0
-----------------------------------------------------------------------------------------

===========================
ECCENTRICITY RELATED DATA
===========================

STORY STORY STORY ACCIDENTAL ACCIDENTAL ACCIDENTAL ACCIDENTAL

NAME FORCE(X) FORCE(Y) ECCENT.(X) ECCENT.(Y) TORSION(X) TORSION(Y)
---------- ---------- ---------- ---------- ---------- ---------- ----------
Roof 0.0 71.204064 0.0 0.0 0.0 0.0
4F 0.0 317.88875 0.0 0.0 0.0 0.0
3F 0.0 482.8654 0.0 0.0 0.0 0.0
2F 0.0 552.17971 0.0 0.0 0.0 0.0
G.L. -- -- 0.0 0.0 -- --

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:47
http://www.MidasUser.com
Gen 2021 -5/5-
midas Gen SEIS LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.spf

* MASS GENERATION DATA FOR LATERAL ANALYSIS OF BUILDING [UNIT: kN, m]

_________________________________________________________

STORY TRANSLATIONAL MASS ROTATIONAL CENTER OF MASS

NAME (X-DIR) (Y-DIR) MASS (X-COORD) (Y-COORD)
----------- ----------- ----------- ----------- ----------- -----------
Roof 0.64863996 0.64863996 772.298843 13.52275 44.85
4F 176.583759 176.583759 115982.466 16.4422173 51.6497847
3F 842.993764 842.993764 520837.547 16.9053798 52.6418911
2F 853.404107 853.404107 527674.699 16.9388312 52.5244546
1F 707.624505 707.624505 354342.959 18.3844407 58.4461305
B 1477.79101 1477.79101 442551.395 20.8647649 63.8142216
----------- ----------- ----------- ----------- ----------- -----------
TOTAL : 4059.04579 4059.04579

* ADDITIONAL MASSES FOR THE CALCULATION OF EQUIVALENT SEISMIC FORCE

_____________________________________________________________________

Note. The following masses are between two adjacent stories or on the
nodes released from floor rigid diaphragm by *Diaphragm Disconnect command.
The masses are proportionally distributed to upper/lower stories according
to their vertical locations. For dynamic analysis, however, floor masses
and masses on vertical elements remain at their original locations.

STORY TRANSLATIONAL MASS

NAME (X-DIR) (Y-DIR)
-------------- ----------- -----------
Roof 0.0 0.0
4F 0.0 0.0
3F 0.0 0.0
2F 0.0 0.0
1F 104.07731 104.07731
B 142.868276 142.868276
-------------- ----------- -----------
TOTAL : 246.945586 246.945586

* EQUIVALENT SEISMIC LOAD IN ACCORDANCE WITH UNIFORM BUILDING CODE 1997 [UNIT: kN, m]
_____________________________________________________________________________________________

Seismic Zone Factor (Z) : 0.40

Importance Factor (I) : 1.00
Soil Profile Type : SD

Seismic Source Type : B

Closest Distance To Known Seismic Source [km] : 10.00
Near Source Factor, Na (UBC-97 Table 16-S) : 1.00
Near Source Factor, Nv (UBC-97 Table 16-T) : 1.00

Seismic Coefficient, Ca (UBC-97 Table 16-Q) : 0.44

Seismic Coefficient, Cv (UBC-97 Table 16-R) : 0.64

Fundamental Period Associated With X-dir. (Tx) : 0.1980

R Factor of Lateral System for X-direction (Rx) : 8.0000
Seismic Coefficient for X-dir. UBC-97(Para.1630.2.1) : 0.137500

Fundamental Period Associated With Y-dir. (Ty) : 0.1980

R Factor of Lateral System for Y-direction (Ry) : 8.0000
Seismic Coefficient for Y-dir. UBC-97(Para.1630.2.1) : 0.137500

Total Effective Weight For X-dir. Seismic Loads (Wx) : 26332.366434

Total Effective Weight For Y-dir. Seismic Loads (Wy) : 26332.366434

Scale Factor For X-directional Seismic Loads : 1.00

Scale Factor For Y-directional Seismic Loads : 0.00

Accidental Eccentricity For X-direction (Ex) : Positive

Accidental Eccentricity For Y-direction (Ey) : Positive

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:44
http://www.MidasUser.com
Gen 2021 -1/6-
midas Gen SEIS LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.spf

Torsional Amplification for Accidental Eccentricity : Do not Consider

Torsional Amplification for Inherent Eccentricity : Do not Consider

Total Base Shear Of Model For X-direction : 3620.700385

Total Base Shear Of Model For Y-direction : 0.000000
Summation Of Wi*Hi Of Model For X-direction : 251725.396218
Summation Of Wi*Hi Of Model For Y-direction : 0.000000
--------------------------------------------------------------------------------------

===========================
ECCENTRICITY RELATED DATA
===========================

X - D I R E C T I O N A L L O A D Y - D I R E C T I O N A L L O A
D

STORY ACCIDENTAL INHERENT ACCIDENTAL INHERENT ACCIDENTAL INHERENT ACCIDENTAL INH

ERENT
NAME ECCENT. ECCENT. AMP.FACTOR AMP.FACTOR ECCENT. ECCENT. AMP.FACTOR AMP
.FACTOR
---------- ---------- ---------- ---------- ---------- ---------- ---------- ---------- ---
-------
Roof -4.09 0.0 1.0 0.0 2.00705 0.0 1.0
0.0
4F -4.09 0.0 1.0 0.0 2.00705 0.0 1.0
0.0
3F -4.09 0.0 1.0 0.0 2.00705 0.0 1.0
0.0
2F -4.09 0.0 1.0 0.0 2.00705 0.0 1.0
0.0
1F -4.09 0.0 1.0 0.0 2.00705 0.0 1.0
0.0
G.L 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0
------------------------------------------------------------------------------------------------
-------

------------------------------------------------------------------------------------------------
-------
The accidental amplification factors are automatically set to 1.0 when torsional amplification e
ffect
to accidental eccentricity is not considered.
The inherent amplification factors are automatically set to 0 when torsional amplification effec
t
to inherent eccentricity is not considered.
The inherent amplification factors are all set to 'the input value - 1.0'.(This is to exclude th
e true
inherent torsion)
------------------------------------------------------------------------------------------------
-------

** Story Force , Seismic Force x Scale Factor + Added Force

S E I S M I C L O A D G E N E R A T I O N D A T A X - D I R E C T I O N

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:44
http://www.MidasUser.com
Gen 2021 -2/6-
midas Gen SEIS LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.spf

3F 8266.397 13.7 1628.93 0.0 1628.93 447.5691 1881.887 6662.323 0.0 6

662.323
2F 8368.481 9.5 1143.499 0.0 1143.499 2076.499 10603.18 4676.911 0.0 4
676.911
1F 7959.548 3.5 400.7025 0.0 400.7025 3219.998 29923.17 1638.873 0.0 1
638.873
G.L. -- 0.0 -- -- -- 3620.7 42595.62 --- ---
---
------------------------------------------------------------------------------------------------
-------

S E I S M I C L O A D G E N E R A T I O N D A T A Y - D I R E C T I O N

STORY STORY STORY SEISMIC ADDED STORY STORY OVERTURN. ACCIDENT. INHERENT T
OTAL
NAME WEIGHT LEVEL FORCE FORCE FORCE SHEAR MOMENT TORSION TORSION T
ORSION
---------- -------- ------- -------- -------- -------- -------- --------- --------- --------- --
-------
Roof 6.360563 19.1 1.747409 0.0 0.0 0.0 0.0 0.0 0.0
0.0
4F 1731.58 17.9 445.8217 0.0 0.0 0.0 0.0 0.0 0.0
0.0
3F 8266.397 13.7 1628.93 0.0 0.0 0.0 0.0 0.0 0.0
0.0
2F 8368.481 9.5 1143.499 0.0 0.0 0.0 0.0 0.0 0.0
0.0
1F 7959.548 3.5 400.7025 0.0 0.0 0.0 0.0 0.0 0.0
0.0
G.L. -- 0.0 -- -- -- 0.0 0.0 --- ---
---
------------------------------------------------------------------------------------------------
-------

=================================================
COMMENTS ABOUT TORSION
=================================================

------------------------------------------------------------------------------------------------
-------
If torsional amplification effects are considered :
------------------------------------------------------------------------------------------------
-------
Accidental Torsion , Story Force * Accidental Eccentricity * Amp. Factor for Accidental Eccentri
city
Inherent Torsion , Story Force * Inherent Eccentricity * Amp. Factor for Inherent Eccentricity

------------------------------------------------------------------------------------------------
-------
If torsional amplification effects are not considered :
------------------------------------------------------------------------------------------------
-------
Accidental Torsion , Story Force * Accidental Eccentricity
Inherent Torsion , 0

------------------------------------------------------------------------------------------------
-------
The inherent torsion above is the additional torsion due to torsional amplification effect.
The true inherent torsion is considered automatically in analysis stage when the seismic force i
s
applied to the structure.
------------------------------------------------------------------------------------------------
-------

* MASS GENERATION DATA FOR LATERAL ANALYSIS OF BUILDING [UNIT: kN, m]

_________________________________________________________

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:44
http://www.MidasUser.com
Gen 2021 -3/6-
midas Gen SEIS LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.spf

STORY TRANSLATIONAL MASS ROTATIONAL CENTER OF MASS

* ADDITIONAL MASSES FOR THE CALCULATION OF EQUIVALENT SEISMIC FORCE

_____________________________________________________________________

STORY TRANSLATIONAL MASS

* EQUIVALENT SEISMIC LOAD IN ACCORDANCE WITH UNIFORM BUILDING CODE 1997 [UNIT: kN, m]
_____________________________________________________________________________________________

Seismic Zone Factor (Z) : 0.40

Importance Factor (I) : 1.00
Soil Profile Type : SD

Seismic Source Type : B

Closest Distance To Known Seismic Source [km] : 10.00
Near Source Factor, Na (UBC-97 Table 16-S) : 1.00
Near Source Factor, Nv (UBC-97 Table 16-T) : 1.00

Seismic Coefficient, Ca (UBC-97 Table 16-Q) : 0.44

Seismic Coefficient, Cv (UBC-97 Table 16-R) : 0.64

Fundamental Period Associated With X-dir. (Tx) : 0.1980

R Factor of Lateral System for X-direction (Rx) : 8.0000
Seismic Coefficient for X-dir. UBC-97(Para.1630.2.1) : 0.137500

Fundamental Period Associated With Y-dir. (Ty) : 0.1980

R Factor of Lateral System for Y-direction (Ry) : 8.0000
Seismic Coefficient for Y-dir. UBC-97(Para.1630.2.1) : 0.137500

Total Effective Weight For X-dir. Seismic Loads (Wx) : 26332.366434

Total Effective Weight For Y-dir. Seismic Loads (Wy) : 26332.366434

Scale Factor For X-directional Seismic Loads : 0.00

Scale Factor For Y-directional Seismic Loads : 1.00

Accidental Eccentricity For X-direction (Ex) : Positive

Accidental Eccentricity For Y-direction (Ey) : Positive

Torsional Amplification for Accidental Eccentricity : Do not Consider

Torsional Amplification for Inherent Eccentricity : Do not Consider

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:44
http://www.MidasUser.com
Gen 2021 -4/6-
midas Gen SEIS LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.spf

Total Base Shear Of Model For X-direction : 0.000000

Total Base Shear Of Model For Y-direction : 3620.700385
Summation Of Wi*Hi Of Model For X-direction : 0.000000
Summation Of Wi*Hi Of Model For Y-direction : 251725.396218
--------------------------------------------------------------------------------------

===========================
ECCENTRICITY RELATED DATA
===========================

X - D I R E C T I O N A L L O A D Y - D I R E C T I O N A L L O A
D

STORY ACCIDENTAL INHERENT ACCIDENTAL INHERENT ACCIDENTAL INHERENT ACCIDENTAL INH

** Story Force , Seismic Force x Scale Factor + Added Force

S E I S M I C L O A D G E N E R A T I O N D A T A X - D I R E C T I O N

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:44
http://www.MidasUser.com
Gen 2021 -5/6-
midas Gen SEIS LOAD CALC.

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.spf

0.0
1F 7959.548 3.5 400.7025 0.0 0.0 0.0 0.0 0.0 0.0
0.0
G.L. -- 0.0 -- -- -- 0.0 0.0 --- ---
---
------------------------------------------------------------------------------------------------
-------

S E I S M I C L O A D G E N E R A T I O N D A T A Y - D I R E C T I O N

STORY STORY STORY SEISMIC ADDED STORY STORY OVERTURN. ACCIDENT. INHERENT T
OTAL
NAME WEIGHT LEVEL FORCE FORCE FORCE SHEAR MOMENT TORSION TORSION T
ORSION
---------- -------- ------- -------- -------- -------- -------- --------- --------- --------- --
-------
Roof 6.360563 19.1 1.747409 0.0 1.747409 0.0 0.0 3.507137 0.0 3
.507137
4F 1731.58 17.9 445.8217 0.0 445.8217 1.747409 2.096891 894.7865 0.0 8
94.7865
3F 8266.397 13.7 1628.93 0.0 1628.93 447.5691 1881.887 3269.344 0.0 3
269.344
2F 8368.481 9.5 1143.499 0.0 1143.499 2076.499 10603.18 2295.06 0.0
2295.06
1F 7959.548 3.5 400.7025 0.0 400.7025 3219.998 29923.17 804.2299 0.0 8
04.2299
G.L. -- 0.0 -- -- -- 3620.7 42595.62 --- ---
---
------------------------------------------------------------------------------------------------
-------

=================================================
COMMENTS ABOUT TORSION
=================================================

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/03/2025 05:44
http://www.MidasUser.com
Gen 2021 -6/6-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

------------------------------------------------------------------------------------------
midas Gen - Steel Code Checking[ AISC(15th)-LRFD16 ] Gen 2021
==========================================================================================

+============================================================+
| MIDAS(Modeling, Integrated Design & Analysis Software) |
| midas Gen - Design & checking system for windows |
+============================================================+
| Steel Member Applicable Code Checking |
| Based On Eurocode3:05, Eurocode3, AISC(15th)-LRFD16, |
| AISC(15th)-ASD16, AISC(14th)-LRFD10, |
| AISC(14th)-ASD10, AISC(13th)-LRFD05, |
| AISC(13th)-ASD05, AISC-LRFD2K, AISC-LRFD93, |
| AISC-ASD89, CSA-S16-01, BS5950-90 |
| |
| |
| |
| |
| |
| |
| (c)SINCE 1989 |
+============================================================+
| MIDAS Information Technology Co.,Ltd. (MIDAS IT) |
| MIDAS IT Design Development Team |
+============================================================+
| HomePage : www.MidasUser.com |
+============================================================+
| Gen 2021 |
+============================================================+

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

--------------------------------------------------------------------------------------
LCB C Loadcase Name(Factor) + Loadcase Name(Factor) + Loadcase Name(Factor)
--------------------------------------------------------------------------------------
1 1 DL( 1.400)
2 1 DL( 1.200) + LL( 1.600)
3 1 DL( 1.200) + WL-X( 1.000) + LL( 1.000)
4 1 DL( 1.200) + WL-Y( 1.000) + LL( 1.000)
5 1 DL( 1.200) + WL-X(-1.000) + LL( 1.000)
6 1 DL( 1.200) + WL-Y(-1.000) + LL( 1.000)
7 1 DL( 1.200) + EL-X( 1.000) + LL( 1.000)
8 1 DL( 1.200) + EL-Y( 1.000) + LL( 1.000)
9 1 DL( 1.200) + EL-X(-1.000) + LL( 1.000)
10 1 DL( 1.200) + EL-Y(-1.000) + LL( 1.000)
11 1 DL( 1.200) + RS-M(RS)( 1.000) + LL( 1.000)
12 1 DL( 1.200) + RS-O(RS)( 1.000) + LL( 1.000)
13 1 DL( 1.200) + RS-M(RS)(-1.000) + LL( 1.000)
14 1 DL( 1.200) + RS-O(RS)(-1.000) + LL( 1.000)
15 1 DL( 0.900) + WL-X( 1.000)
16 1 DL( 0.900) + WL-Y( 1.000)
17 1 DL( 0.900) + WL-X(-1.000)
18 1 DL( 0.900) + WL-Y(-1.000)
19 1 DL( 0.900) + EL-X( 1.000)
20 1 DL( 0.900) + EL-Y( 1.000)
21 1 DL( 0.900) + EL-X(-1.000)
22 1 DL( 0.900) + EL-Y(-1.000)
23 1 DL( 0.900) + RS-M(RS)( 1.000)
24 1 DL( 0.900) + RS-O(RS)( 1.000)

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:18
http://www.MidasUser.com
Gen 2021 -1/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

25 1 DL( 0.900) + RS-M(RS)(-1.000)

26 1 DL( 0.900) + RS-O(RS)(-1.000)
--------------------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:18
http://www.MidasUser.com
Gen 2021 -2/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. PROJECT :
*. MEMBER NO = 353, ELEMENT TYPE = Beam
*. LOADCOMB NO = 8, MATERIAL NO = 1, SECTION NO = 38
*. UNIT SYSTEM : kN, m

*. SECTION PROPERTIES : Designation = HM 594x302x14/23

Shape = I - Section. (Rolled)
Depth = 0.594, Top F Width = 0.302, Bot.F Width = 0.302
Web Thick = 0.014, Top F Thick = 0.023, Bot.F Thick = 0.023

Area = 2.17090e-02, Asy = 9.26133e-03, Asz = 8.31600e-03

Ybar = 1.51000e-01, Zbar = 2.97000e-01, Qyb = 1.79187e-01, Qzb = 1.14005e-02
Syy = 4.45000e-03, Szz = 7.00100e-04, Zyy = 5.01723e-03, Zzz = 1.07570e-03
Iyy = 1.32179e-03, Izz = 1.05720e-04, Iyz = 0.00000e+00
ry = 2.46800e-01, rz = 6.98000e-02
J = 2.97190e-06, Cwp = 8.61726e-06

*. DESIGN PARAMETERS FOR STRENGTH EVALUATION :

Ly = 4.20000e+00, Lz = 4.20000e+00, Lu = 4.20000e+00
Ky = 1.00000e+00, Kz = 1.00000e+00

*. MATERIAL PROPERTIES :
Fy = 2.48211e+05, Es = 1.99948e+08, MATERIAL NAME = A36

======================================================================================
[[[*]]] COMPUTE MOMENT MAGNIFICATION FACTORS AND MAGNIFIED MOMENTS.
======================================================================================

( ). Factored force/moments caused by unit load case.

*.Load combination ID = 8
-------------------------------------------------------------------------------
Load Case Pa Myi Myj Mzi Mzj
-------------------------------------------------------------------------------
DL -300.12 146.42 -144.82 -9.45 9.39
LL -123.60 70.25 -69.81 -4.48 4.51
DL+LL -423.72 216.67 -214.63 -13.93 13.90
OTHER CASES -4.59 -0.49 6.36 -108.04 113.96
-------------------------------------------------------------------------------
TOTAL -428.31 216.18 -208.27 -121.97 127.86
-------------------------------------------------------------------------------
*.Member end moments caused by gravity load(DL+LL).
My1G = 214.63, My2G = 216.67
Mz1G = 13.90, Mz2G = 13.93

( ). Compute coefficient assuming no lateral translation of the frame (Cmy, Cmz)

[ AISC(15th) Specification C2.1.1b. (C2-4) ]
-. Cmy = 0.850 (User defined or default value)
-. Cmz = 0.850 (User defined or default value)

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:18
http://www.MidasUser.com
Gen 2021 -3/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Compute moment magnification factors(B1y,B1z).

-. Pu = Pu(DL+LL) + Pu(WL(EL)) = 428.31 kN.
-. About major(Local-y) axis.
SLENy = Ky*Ly/ry = 17.02
Lambda = (SLENy/pi)*SQRT(Fy/Es) = 0.1909
Pey = (Area*Fy)/Lambda^2 = 147927.33 kN.
B1y = Cmy / (1-Pu/Pey) = 0.85
B1y < 1.0 ---> B1y = 1.00
-. About minor(Local-z) axis.
SLENz = Kz*Lz/rz = 60.17
Lambda = (SLENz/pi)*SQRT(Fy/Es) = 0.6748
Pez = (Area*Fy)/Lambda^2 = 11832.29 kN.
B1z = Cmz / (1-Pu/Pez) = 0.88
B1z < 1.0 ---> B1z = 1.00

( ). Magnification factors for sidesway moments(B2y,B2z).

-. B2y = 1.00 (Default value)
-. B2z = 1.00 (Default value)

( ). Given factored axial forces and moments at <J>.

----------------------------------------------------------------
Load Case Pa My Mz
----------------------------------------------------------------
DL -300.12 -144.82 9.39
LL -123.60 -69.81 4.51
DL+LL -423.72 -214.63 13.90
OTHER CASES -4.59 6.36 113.96
----------------------------------------------------------------
TOTAL -428.31 -208.27 127.86
----------------------------------------------------------------

( ). Compute magnified moments.

-. Muy = B1y*My(DL+LL) + B2y*My(OTHERS) = -208.27 kN-m.
-. Muz = B1z*Mz(DL+LL) + B2z*Mz(OTHERS) = 127.86 kN-m.

======================================================================================
[[[*]]] CHECK AXIAL STRENGTH.
======================================================================================

( ). Check slenderness ratio of axial compression member (KL/r).

[ AISC(15th) Specification E2. ]
-. KL/r = 60.2 < 200.0 ---> O.K.

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1a> ]
-. Lambda_r = 0.56*SQRT[Es/Fy] = 15.89
-. BTR = bf/2tf = 6.57 < Lambda_r ---> NON-SLENDER SECTION !

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:18
http://www.MidasUser.com
Gen 2021 -4/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Check depth-thickness ratio of web (DTR).

[ AISC(15th) Specification B4. <Table B4.1a> ]
-. Lambda_r = 1.49*SQRT[Es/Fy] = 42.29
-. Dweb = H-tf1-tf2 = 0.52 m.
-. DTR = Dweb/tw = 37.29 < Lambda_r ---> NON-SLENDER SECTION !

( ). Calculate Flexural Buckling Stress (Fcr1).

[ AISC(15th) Specification E3 ]
pi^2 * E
-. Fe = ----------- = 545040.9411 KPa.
(Lc/r)^2
-. Lc/r = 60.172
-. 4.71 * SQRT[Es/Fy] = 133.681
-. Fy/Fe = 0.4554
-. When Lc/r < 4.71 * SQRT[Es/Fy]
-. Fcr1 = (0.658)^(Fy/Fe) * Fy = 205135.9573 KPa.

( ). Calculate axial compressive strength (phiPn).

[ AISC(15th) Specification E1. ]
-. Fcr = 205135.9573 KPa.
-. Resistance factor for compression : phi = 0.90
-. phiPn = phi*Area*Fcr = 4007.97 kN.

( ). Check ratio of axial strength (Pu/phiPn).

Pu 428.31
-. ------- = --------------- = 0.107 < 1.000 ---> O.K.
phiPn 4007.97

======================================================================================
[[[*]]] CHECK FLEXURAL STRENGTH ABOUT MAJOR AXIS.
======================================================================================

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0045 m^3.
-. Syt = 0.0045 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Calculate limiting width-thickness ratio of web for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 3.76*SQRT[Es/Fy] = 106.72
-. Lambda_r = 5.70*SQRT[Es/Fy] = 161.78

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 6.57 < Lambda_p = 10.79 ---> COMPACT.

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:18
http://www.MidasUser.com
Gen 2021 -5/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Check width-thickness ratio of web (DTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. DTR = 37.29 < Lambda_p = 106.72 ---> COMPACT.

( ). Calculate lateral-torsional buckling modification factor (Cb).

[ AISC(15th) Specification F1.(2) (F1-1) ]
-. Cb = 1.000 (User defined or default value)

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F2.1 (F2-1) ]
-. Mn.Y = Mp = Fy*Zyy = 1245.33 kN-m.

--------------------------------------------------------------------------
[*] Check Lateral-Torsional Buckling (LTB).
--------------------------------------------------------------------------

( ). Compute limiting laterally unbraced length for the limit state of yielding (Lp).
[ AISC(15th) Specification F2.2 (F2-5) ]
-. Lp = 1.76*rz*SQRT[Es/Fy] = 3.49 m.

( ). Compute laterally unbraced length for the limit state of inelastic lateral-
torsional buckling (Lr).
[ AISC(15th) Specification F2.2 (F2-6) ]
[ SQRT[Rzz*Cw] ]
-. rts = SQRT[ ------------ ] = 0.08 m.
[ Syy ]
-. c = 1.00 (for a doubly symmetry H-Shape)
-. h0 = H - 0.5*(tf1+tf2) = 0.57 m. (distance between the flange centroid)
Es
-. X1 = ------ = 39.36
0.7Fy
J*c
-. X2 = ------ = 4.73
Syy*h0
-. Lr = 1.95*rts*X1 * SQRT[ X2 +SQRT[ X2^2 + 6.76*(1/X1)^2 ] ] = 11.26 m.

( ). Calculate nominal flexural strength for Lateral-torsional buckling (LTB).

[ AISC(15th) Specification F2.2 (F2-2) ]
-. Lp < Lb < Lr.
[ Lb-Lp ]
-. Mn = Cb *[ Mp - (Mp-0.7*Fy*Syy) * ------- ] = 1202.02 kN-m.
[ Lr-Lp ]
-. Mn.LTB = MIN [ Mn, Mp ] = 1202.02 kN-m.

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:18
http://www.MidasUser.com
Gen 2021 -6/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Compute flexural strength about major axis (phiMny).

-. Mny = MIN[ Mn.Y, Mn.LTB ] = 1202.02 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMny = phi*Mny = 1081.82 kN-m.

( ). Check ratio of flexural strength (Muy/phiMny).

Muy 208.27
-. -------- = --------------- = 0.193 < 1.000 ---> O.K.
phiMny 1081.82

======================================================================================
[[[*]]] CHECK FLEXURAL STRENGTH ABOUT MINOR AXIS.
======================================================================================

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0045 m^3.
-. Syt = 0.0045 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 6.57 < Lambda_p = 10.79 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F6.1 (F6-1) ]
-. Mn.Y = Mp = MIN[ Fy*Zzz, 1.6*Fy*Szz ] = 267.00 kN-m.

--------------------------------------------------------------------------
[*] Check Flange Local Buckling (FLB).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Flange local buckling (FLB).

-. COMPACT flange ---> the limit state of flange local buckling is not applied.

( ). Compute flexural strength about minor axis (phiMnz).

-. Mnz = Mn.Y = 267.00 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMnz = phi*Mnz = 240.30 kN-m.

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:18
http://www.MidasUser.com
Gen 2021 -7/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Check ratio of flexural strength (Muz/phiMnz).

Muz 127.86
-. -------- = --------------- = 0.532 < 1.000 ---> O.K.
phiMnz 240.30

======================================================================================
[[[*]]] CHECK INTERACTION OF COMBINED STRENGTH.
======================================================================================

( ). Check interaction ratio of combined strength.

[ AISC(15th) Specification H1.1(b) ]
-. Pr/Pc < 0.20 ---> Formula(H1-1b)
Pr [ Mry Mrz ]
-. ComRat = ------ + [ ----- + ----- ]
2*Pc [ Mcy Mcz ]
= 0.053 + [ 0.193 + 0.532 ]
= 0.778 < 1.000 ---> O.K.

======================================================================================
[[[*]]] CHECK SHEAR STRENGTH.
======================================================================================

( ). Calculate the web shear buckling coefficient (Cv2).

[ AISC(15th) Specification G2.2 (G2-9) ]
-. for webs of all other doubly/singly symmetric shapes and channels.
-. kv (web plate buckling coefficient) = 1.20
-. h/tw = 6.565< 1.10*SQRT[kv*Es/Fy] = 34.200
-. Cv2 = 1.00

( ). Calculate shear strength in local-y direction (phiVny).

-. Aw = 0.01 m^2.
-. Vn = 0.6*Fy*Aw*Cv2 = 2068.8912 kN.
-. Resistance factor for shear : phi = 0.90
-. phiVny = phi*Vn = 1862.00 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 8, POS = J )
-. Applied shear force : Vuy = 59.48 kN.
Vuy 59.48
-. -------- = --------------- = 0.032 < 1.000 ---> O.K.
phiVny 1862.00

( ). Calculate shear strength coefficient (Cv1).

[ AISC(15th) Specification G2.1 (G2-2) ]
-. for Rolled H-Shape members.
-. h/tw = 37.286 < 2.24*SQRT[Es/Fy] = 63.576
-. Cv1 = 1.00

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:18
http://www.MidasUser.com
Gen 2021 -8/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Calculate shear strength in local-z direction (phiVnz).

-. Aw = 8.32e-03 m^2.
-. Vn = 0.6*Fy*Aw*Cv1 = 1238.4753 kN.
-. for webs of rolled H-shape members with h/tw < 2.24*SQRT[Es/Fy].
-. Resistance factor for shear : phi = 1.00
-. phiVnz = phi*Vn = 1238.48 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 7, POS = J )
-. Applied shear force : Vuz = 148.73 kN.
Vuz 148.73
-. -------- = --------------- = 0.120 < 1.000 ---> O.K.
phiVnz 1238.48

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:18
http://www.MidasUser.com
Gen 2021 -9/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -1/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

25 1 DL( 0.900) + RS-M(RS)(-1.000)

26 1 DL( 0.900) + RS-O(RS)(-1.000)
--------------------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -2/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. PROJECT :
*. MEMBER NO = 21, ELEMENT TYPE = Beam
*. LOADCOMB NO = 10, MATERIAL NO = 1, SECTION NO = 35
*. UNIT SYSTEM : kN, m

*. SECTION PROPERTIES : Designation = HW 350x350x12/19

Shape = I - Section. (Rolled)
Depth = 0.350, Top F Width = 0.350, Bot.F Width = 0.350
Web Thick = 0.012, Top F Thick = 0.019, Bot.F Thick = 0.019

Area = 1.71890e-02, Asy = 8.86666e-03, Asz = 4.20000e-03

Ybar = 1.75000e-01, Zbar = 1.75000e-01, Qyb = 1.03882e-01, Qzb = 1.53125e-02
Syy = 2.26500e-03, Szz = 7.76000e-04, Zyy = 2.49318e-03, Zzz = 1.17498e-03
Iyy = 3.96370e-04, Izz = 1.35820e-04, Iyz = 0.00000e+00
ry = 1.51900e-01, rz = 8.89000e-02
J = 1.79109e-06, Cwp = 3.72014e-06

*. DESIGN PARAMETERS FOR STRENGTH EVALUATION :

Ly = 4.80000e+00, Lz = 4.80000e+00, Lu = 4.80000e+00
Ky = 1.00000e+00, Kz = 1.00000e+00

*. MATERIAL PROPERTIES :
Fy = 2.48211e+05, Es = 1.99948e+08, MATERIAL NAME = A36

( ). Factored force/moments caused by unit load case.

*.Load combination ID = 10
-------------------------------------------------------------------------------
Load Case Pa Myi Myj Mzi Mzj
-------------------------------------------------------------------------------
DL -157.50 -14.40 33.97 3.99 -6.06
LL -63.32 -3.76 15.80 1.50 -2.79
DL+LL -220.82 -18.16 49.77 5.49 -8.85
OTHER CASES -88.66 -33.77 18.94 156.96 -128.40
-------------------------------------------------------------------------------
TOTAL -309.48 -51.93 68.71 162.45 -137.25
-------------------------------------------------------------------------------
*.Member end moments caused by gravity load(DL+LL).
My1G = 18.16, My2G = 49.77
Mz1G = 5.49, Mz2G = 8.85

( ). Compute coefficient assuming no lateral translation of the frame (Cmy, Cmz)

[ AISC(15th) Specification C2.1.1b. (C2-4) ]
-. Cmy = 0.850 (User defined or default value)
-. Cmz = 0.850 (User defined or default value)

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -3/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Compute moment magnification factors(B1y,B1z).

-. Pu = Pu(DL+LL) + Pu(WL(EL)) = 309.48 kN.
-. About major(Local-y) axis.
SLENy = Ky*Ly/ry = 31.60
Lambda = (SLENy/pi)*SQRT(Fy/Es) = 0.3544
Pey = (Area*Fy)/Lambda^2 = 33970.39 kN.
B1y = Cmy / (1-Pu/Pey) = 0.86
B1y < 1.0 ---> B1y = 1.00
-. About minor(Local-z) axis.
SLENz = Kz*Lz/rz = 53.99
Lambda = (SLENz/pi)*SQRT(Fy/Es) = 0.6055
Pez = (Area*Fy)/Lambda^2 = 11635.59 kN.
B1z = Cmz / (1-Pu/Pez) = 0.87
B1z < 1.0 ---> B1z = 1.00

( ). Magnification factors for sidesway moments(B2y,B2z).

-. B2y = 1.00 (Default value)
-. B2z = 1.00 (Default value)

( ). Given factored axial forces and moments at <I>.

----------------------------------------------------------------
Load Case Pa My Mz
----------------------------------------------------------------
DL -157.50 -14.40 3.99
LL -63.32 -3.76 1.50
DL+LL -220.82 -18.16 5.49
OTHER CASES -88.66 -33.77 156.96
----------------------------------------------------------------
TOTAL -309.48 -51.93 162.45
----------------------------------------------------------------

( ). Compute magnified moments.

-. Muy = B1y*My(DL+LL) + B2y*My(OTHERS) = -51.93 kN-m.
-. Muz = B1z*Mz(DL+LL) + B2z*Mz(OTHERS) = 162.45 kN-m.

( ). Check slenderness ratio of axial compression member (KL/r).

[ AISC(15th) Specification E2. ]
-. KL/r = 54.0 < 200.0 ---> O.K.

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1a> ]
-. Lambda_r = 0.56*SQRT[Es/Fy] = 15.89
-. BTR = bf/2tf = 9.21 < Lambda_r ---> NON-SLENDER SECTION !

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -4/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Check depth-thickness ratio of web (DTR).

[ AISC(15th) Specification B4. <Table B4.1a> ]
-. Lambda_r = 1.49*SQRT[Es/Fy] = 42.29
-. Dweb = H-tf1-tf2 = 0.29 m.
-. DTR = Dweb/tw = 23.83 < Lambda_r ---> NON-SLENDER SECTION !

( ). Calculate Flexural Buckling Stress (Fcr1).

[ AISC(15th) Specification E3 ]
pi^2 * E
-. Fe = ----------- = 676920.8772 KPa.
(Lc/r)^2
-. Lc/r = 53.993
-. 4.71 * SQRT[Es/Fy] = 133.681
-. Fy/Fe = 0.3667
-. When Lc/r < 4.71 * SQRT[Es/Fy]
-. Fcr1 = (0.658)^(Fy/Fe) * Fy = 212896.8465 KPa.

( ). Calculate axial compressive strength (phiPn).

[ AISC(15th) Specification E1. ]
-. Fcr = 212896.8465 KPa.
-. Resistance factor for compression : phi = 0.90
-. phiPn = phi*Area*Fcr = 3293.54 kN.

( ). Check ratio of axial strength (Pu/phiPn).

Pu 309.48
-. ------- = --------------- = 0.094 < 1.000 ---> O.K.
phiPn 3293.54

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0023 m^3.
-. Syt = 0.0023 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Calculate limiting width-thickness ratio of web for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 3.76*SQRT[Es/Fy] = 106.72
-. Lambda_r = 5.70*SQRT[Es/Fy] = 161.78

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 9.21 < Lambda_p = 10.79 ---> COMPACT.

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -5/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Check width-thickness ratio of web (DTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. DTR = 23.83 < Lambda_p = 106.72 ---> COMPACT.

( ). Calculate lateral-torsional buckling modification factor (Cb).

[ AISC(15th) Specification F1.(2) (F1-1) ]
-. Cb = 1.000 (User defined or default value)

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F2.1 (F2-1) ]
-. Mn.Y = Mp = Fy*Zyy = 618.84 kN-m.

--------------------------------------------------------------------------
[*] Check Lateral-Torsional Buckling (LTB).
--------------------------------------------------------------------------

( ). Compute limiting laterally unbraced length for the limit state of yielding (Lp).
[ AISC(15th) Specification F2.2 (F2-5) ]
-. Lp = 1.76*rz*SQRT[Es/Fy] = 4.44 m.

( ). Compute laterally unbraced length for the limit state of inelastic lateral-
torsional buckling (Lr).
[ AISC(15th) Specification F2.2 (F2-6) ]
[ SQRT[Rzz*Cw] ]
-. rts = SQRT[ ------------ ] = 0.10 m.
[ Syy ]
-. c = 1.00 (for a doubly symmetry H-Shape)
-. h0 = H - 0.5*(tf1+tf2) = 0.33 m. (distance between the flange centroid)
Es
-. X1 = ------ = 56.25
0.7Fy
J*c
-. X2 = ------ = 1.89
Syy*h0
-. Lr = 1.95*rts*X1 * SQRT[ X2 +SQRT[ X2^2 + 6.76*(1/X1)^2 ] ] = 16.84 m.

( ). Calculate nominal flexural strength for Lateral-torsional buckling (LTB).

[ AISC(15th) Specification F2.2 (F2-2) ]
-. Lp < Lb < Lr.
[ Lb-Lp ]
-. Mn = Cb *[ Mp - (Mp-0.7*Fy*Syy) * ------- ] = 612.31 kN-m.
[ Lr-Lp ]
-. Mn.LTB = MIN [ Mn, Mp ] = 612.31 kN-m.

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -6/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Compute flexural strength about major axis (phiMny).

-. Mny = MIN[ Mn.Y, Mn.LTB ] = 612.31 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMny = phi*Mny = 551.08 kN-m.

( ). Check ratio of flexural strength (Muy/phiMny).

Muy 51.93
-. -------- = --------------- = 0.094 < 1.000 ---> O.K.
phiMny 551.08

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0023 m^3.
-. Syt = 0.0023 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 9.21 < Lambda_p = 10.79 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F6.1 (F6-1) ]
-. Mn.Y = Mp = MIN[ Fy*Zzz, 1.6*Fy*Szz ] = 291.64 kN-m.

--------------------------------------------------------------------------
[*] Check Flange Local Buckling (FLB).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Flange local buckling (FLB).

-. COMPACT flange ---> the limit state of flange local buckling is not applied.

( ). Compute flexural strength about minor axis (phiMnz).

-. Mnz = Mn.Y = 291.64 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMnz = phi*Mnz = 262.48 kN-m.

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -7/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Check ratio of flexural strength (Muz/phiMnz).

Muz 162.45
-. -------- = --------------- = 0.619 < 1.000 ---> O.K.
phiMnz 262.48

( ). Check interaction ratio of combined strength.

[ AISC(15th) Specification H1.1(b) ]
-. Pr/Pc < 0.20 ---> Formula(H1-1b)
Pr [ Mry Mrz ]
-. ComRat = ------ + [ ----- + ----- ]
2*Pc [ Mcy Mcz ]
= 0.047 + [ 0.094 + 0.619 ]
= 0.760 < 1.000 ---> O.K.

( ). Calculate the web shear buckling coefficient (Cv2).

[ AISC(15th) Specification G2.2 (G2-9) ]
-. for webs of all other doubly/singly symmetric shapes and channels.
-. kv (web plate buckling coefficient) = 1.20
-. h/tw = 9.211< 1.10*SQRT[kv*Es/Fy] = 34.200
-. Cv2 = 1.00

( ). Calculate shear strength in local-y direction (phiVny).

-. Aw = 0.01 m^2.
-. Vn = 0.6*Fy*Aw*Cv2 = 1980.7265 kN.
-. Resistance factor for shear : phi = 0.90
-. phiVny = phi*Vn = 1782.65 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 10, POS = J )
-. Applied shear force : Vuy = 62.44 kN.
Vuy 62.44
-. -------- = --------------- = 0.035 < 1.000 ---> O.K.
phiVny 1782.65

( ). Calculate shear strength coefficient (Cv1).

[ AISC(15th) Specification G2.1 (G2-2) ]
-. for Rolled H-Shape members.
-. h/tw = 23.833 < 2.24*SQRT[Es/Fy] = 63.576
-. Cv1 = 1.00

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -8/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Calculate shear strength in local-z direction (phiVnz).

-. Aw = 4.20e-03 m^2.
-. Vn = 0.6*Fy*Aw*Cv1 = 625.4926 kN.
-. for webs of rolled H-shape members with h/tw < 2.24*SQRT[Es/Fy].
-. Resistance factor for shear : phi = 1.00
-. phiVnz = phi*Vn = 625.49 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 5, POS = J )
-. Applied shear force : Vuz = 71.39 kN.
Vuz 71.39
-. -------- = --------------- = 0.114 < 1.000 ---> O.K.
phiVnz 625.49

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -9/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:19
http://www.MidasUser.com
Gen 2021 -1/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

25 1 DL( 0.900) + RS-M(RS)(-1.000)

26 1 DL( 0.900) + RS-O(RS)(-1.000)
--------------------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:19
http://www.MidasUser.com
Gen 2021 -2/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. PROJECT :
*. MEMBER NO = 731, ELEMENT TYPE = Beam
*. LOADCOMB NO = 5, MATERIAL NO = 1, SECTION NO = 34
*. UNIT SYSTEM : kN, m

*. SECTION PROPERTIES : Designation = I 36a

Shape = I - Section. (Rolled)
Depth = 0.360, Top F Width = 0.136, Bot.F Width = 0.136
Web Thick = 0.010, Top F Thick = 0.016, Bot.F Thick = 0.016

Area = 7.64400e-03, Asy = 2.86507e-03, Asz = 3.60000e-03

Ybar = 6.80000e-02, Zbar = 1.80000e-01, Qyb = 5.04617e-02, Qzb = 2.31200e-03
Syy = 8.77600e-04, Szz = 8.16000e-05, Zyy = 1.00923e-03, Zzz = 1.54328e-04
Iyy = 1.57960e-04, Izz = 5.54900e-06, Iyz = 0.00000e+00
ry = 1.23800e-01, rz = 2.69000e-02
J = 4.72351e-07, Cwp = 1.64353e-07

*. DESIGN PARAMETERS FOR STRENGTH EVALUATION :

Ly = 3.00000e+00, Lz = 3.00000e+00, Lu = 3.00000e+00
Ky = 1.00000e+00, Kz = 1.00000e+00

*. MATERIAL PROPERTIES :
Fy = 2.48211e+05, Es = 1.99948e+08, MATERIAL NAME = A36

( ). Compute moment magnification factors(B1y,B1z).

-. If tension or bending member.
-. Assumed B1y = 1.00
-. Assumed B1z = 1.00

( ). Magnification factors for sidesway moments(B2y,B2z).

-. B2y = 1.00 (Default value)
-. B2z = 1.00 (Default value)

( ). Given factored axial forces and moments at <I>.

----------------------------------------------------------------
Load Case Pa My Mz
----------------------------------------------------------------
DL 0.00 -14.48 0.00
LL 0.00 -8.45 0.00
DL+LL 0.00 -22.93 0.00
OTHER CASES 0.00 -31.07 0.00
----------------------------------------------------------------
TOTAL 0.00 -54.00 0.00
----------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:19
http://www.MidasUser.com
Gen 2021 -3/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Compute magnified moments.

-. Muy = B1y*My(DL+LL) + B2y*My(OTHERS) = -54.00 kN-m.
-. Muz = B1z*Mz(DL+LL) + B2z*Mz(OTHERS) = 0.00 kN-m.

( ). Check slenderness ratio of axial tension member (L/r).

[ AISC(15th) Specification D1. ]
-. L/r = 111.5 < 300.0 ---> O.K.

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0009 m^3.
-. Syt = 0.0009 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Calculate limiting width-thickness ratio of web for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 3.76*SQRT[Es/Fy] = 106.72
-. Lambda_r = 5.70*SQRT[Es/Fy] = 161.78

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 4.30 < Lambda_p = 10.79 ---> COMPACT.

( ). Check width-thickness ratio of web (DTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. DTR = 30.44 < Lambda_p = 106.72 ---> COMPACT.

( ). Calculate lateral-torsional buckling modification factor (Cb).

[ AISC(15th) Specification F1.(2) (F1-1) ]
-. Cb = 1.000 (User defined or default value)

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:19
http://www.MidasUser.com
Gen 2021 -4/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F2.1 (F2-1) ]
-. Mn.Y = Mp = Fy*Zyy = 250.50 kN-m.

--------------------------------------------------------------------------
[*] Check Lateral-Torsional Buckling (LTB).
--------------------------------------------------------------------------

( ). Compute limiting laterally unbraced length for the limit state of yielding (Lp).
[ AISC(15th) Specification F2.2 (F2-5) ]
-. Lp = 1.76*rz*SQRT[Es/Fy] = 1.34 m.

( ). Compute laterally unbraced length for the limit state of inelastic lateral-
torsional buckling (Lr).
[ AISC(15th) Specification F2.2 (F2-6) ]
[ SQRT[Rzz*Cw] ]
-. rts = SQRT[ ------------ ] = 0.03 m.
[ Syy ]
-. c = 1.00 (for a doubly symmetry H-Shape)
-. h0 = H - 0.5*(tf1+tf2) = 0.34 m. (distance between the flange centroid)
Es
-. X1 = ------ = 45.51
0.7Fy
J*c
-. X2 = ------ = 3.09
Syy*h0
-. Lr = 1.95*rts*X1 * SQRT[ X2 +SQRT[ X2^2 + 6.76*(1/X1)^2 ] ] = 4.86 m.

( ). Calculate nominal flexural strength for Lateral-torsional buckling (LTB).

[ AISC(15th) Specification F2.2 (F2-2) ]
-. Lp < Lb < Lr.
[ Lb-Lp ]
-. Mn = Cb *[ Mp - (Mp-0.7*Fy*Syy) * ------- ] = 204.34 kN-m.
[ Lr-Lp ]
-. Mn.LTB = MIN [ Mn, Mp ] = 204.34 kN-m.

( ). Compute flexural strength about major axis (phiMny).

-. Mny = MIN[ Mn.Y, Mn.LTB ] = 204.34 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMny = phi*Mny = 183.91 kN-m.

( ). Check ratio of flexural strength (Muy/phiMny).

Muy 54.00
-. -------- = --------------- = 0.294 < 1.000 ---> O.K.
phiMny 183.91

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:19
http://www.MidasUser.com
Gen 2021 -5/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0009 m^3.
-. Syt = 0.0009 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 4.30 < Lambda_p = 10.79 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F6.1 (F6-1) ]
-. Mn.Y = Mp = MIN[ Fy*Zzz, 1.6*Fy*Szz ] = 32.41 kN-m.

--------------------------------------------------------------------------
[*] Check Flange Local Buckling (FLB).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Flange local buckling (FLB).

-. COMPACT flange ---> the limit state of flange local buckling is not applied.

( ). Compute flexural strength about minor axis (phiMnz).

-. Mnz = Mn.Y = 32.41 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMnz = phi*Mnz = 29.17 kN-m.

( ). Check ratio of flexural strength (Muz/phiMnz).

Muz 0.00
-. -------- = --------------- = 0.000 < 1.000 ---> O.K.
phiMnz 29.17

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:19
http://www.MidasUser.com
Gen 2021 -6/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Check interaction ratio of combined strength.

[ AISC(15th) Specification H1.1(b) ]
-. Pr/Pc < 0.20 ---> Formula(H1-1b)
Pr [ Mry Mrz ]
-. ComRat = ------ + [ ----- + ----- ]
2*Pc [ Mcy Mcz ]
= 0.000 + [ 0.294 + 0.000 ]
= 0.294 < 1.000 ---> O.K.

( ). Calculate shear strength coefficient (Cv1).

[ AISC(15th) Specification G2.1 (G2-2) ]
-. for Rolled H-Shape members.
-. h/tw = 30.440 < 2.24*SQRT[Es/Fy] = 63.576
-. Cv1 = 1.00

( ). Calculate shear strength in local-z direction (phiVnz).

-. Aw = 3.60e-03 m^2.
-. Vn = 0.6*Fy*Aw*Cv1 = 536.1365 kN.
-. for webs of rolled H-shape members with h/tw < 2.24*SQRT[Es/Fy].
-. Resistance factor for shear : phi = 1.00
-. phiVnz = phi*Vn = 536.14 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 5, POS = I )
-. Applied shear force : Vuz = 34.78 kN.
Vuz 34.78
-. -------- = --------------- = 0.065 < 1.000 ---> O.K.
phiVnz 536.14

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:19
http://www.MidasUser.com
Gen 2021 -7/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:19
http://www.MidasUser.com
Gen 2021 -1/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

25 1 DL( 0.900) + RS-M(RS)(-1.000)

26 1 DL( 0.900) + RS-O(RS)(-1.000)
--------------------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:19
http://www.MidasUser.com
Gen 2021 -2/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. PROJECT :
*. MEMBER NO = 451, ELEMENT TYPE = Beam
*. LOADCOMB NO = 2, MATERIAL NO = 1, SECTION NO = 33
*. UNIT SYSTEM : kN, m

*. SECTION PROPERTIES : Designation = I 36c

Shape = I - Section. (Rolled)
Depth = 0.360, Top F Width = 0.140, Bot.F Width = 0.140
Web Thick = 0.014, Top F Thick = 0.016, Bot.F Thick = 0.016

Area = 9.08400e-03, Asy = 2.94933e-03, Asz = 5.04000e-03

Ybar = 7.00000e-02, Zbar = 1.80000e-01, Qyb = 4.06726e-02, Qzb = 2.45000e-03
Syy = 9.64000e-04, Szz = 8.77000e-05, Zyy = 1.13883e-03, Zzz = 1.70932e-04
Iyy = 1.73510e-04, Izz = 6.14000e-06, Iyz = 0.00000e+00
ry = 1.38200e-01, rz = 2.60000e-02
J = 6.82964e-07, Cwp = 1.81857e-07

*. DESIGN PARAMETERS FOR STRENGTH EVALUATION :

Ly = 6.00000e+00, Lz = 6.00000e+00, Lu = 6.00000e+00
Ky = 1.00000e+00, Kz = 1.00000e+00

*. MATERIAL PROPERTIES :
Fy = 2.48211e+05, Es = 1.99948e+08, MATERIAL NAME = A36

( ). Compute moment magnification factors(B1y,B1z).

-. If tension or bending member.
-. Assumed B1y = 1.00
-. Assumed B1z = 1.00

( ). Magnification factors for sidesway moments(B2y,B2z).

-. B2y = 1.00 (Default value)
-. B2z = 1.00 (Default value)

( ). Given factored axial forces and moments at <1/2>.

----------------------------------------------------------------
Load Case Pa My Mz
----------------------------------------------------------------
DL 0.00 41.26 0.00
LL 0.00 35.44 0.00
DL+LL 0.00 76.70 0.00
OTHER CASES 0.00 0.00 0.00
----------------------------------------------------------------
TOTAL 0.00 76.70 0.00
----------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:19
http://www.MidasUser.com
Gen 2021 -3/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Compute magnified moments.

-. Muy = B1y*My(DL+LL) + B2y*My(OTHERS) = 76.70 kN-m.
-. Muz = B1z*Mz(DL+LL) + B2z*Mz(OTHERS) = 0.00 kN-m.

( ). Check slenderness ratio of axial tension member (L/r).

[ AISC(15th) Specification D1. ]
-. L/r = 230.8 < 300.0 ---> O.K.

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0010 m^3.
-. Syt = 0.0010 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Calculate limiting width-thickness ratio of web for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 3.76*SQRT[Es/Fy] = 106.72
-. Lambda_r = 5.70*SQRT[Es/Fy] = 161.78

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 4.43 < Lambda_p = 10.79 ---> COMPACT.

( ). Check width-thickness ratio of web (DTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. DTR = 21.74 < Lambda_p = 106.72 ---> COMPACT.

( ). Calculate lateral-torsional buckling modification factor (Cb).

[ AISC(15th) Specification F1.(2) (F1-1) ]
-. Cb = 1.000 (User defined or default value)

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:19
http://www.MidasUser.com
Gen 2021 -4/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F2.1 (F2-1) ]
-. Mn.Y = Mp = Fy*Zyy = 282.67 kN-m.

--------------------------------------------------------------------------
[*] Check Lateral-Torsional Buckling (LTB).
--------------------------------------------------------------------------

( ). Compute limiting laterally unbraced length for the limit state of yielding (Lp).
[ AISC(15th) Specification F2.2 (F2-5) ]
-. Lp = 1.76*rz*SQRT[Es/Fy] = 1.30 m.

( ). Compute laterally unbraced length for the limit state of inelastic lateral-
torsional buckling (Lr).
[ AISC(15th) Specification F2.2 (F2-6) ]
[ SQRT[Rzz*Cw] ]
-. rts = SQRT[ ------------ ] = 0.03 m.
[ Syy ]
-. c = 1.00 (for a doubly symmetry H-Shape)
-. h0 = H - 0.5*(tf1+tf2) = 0.34 m. (distance between the flange centroid)
Es
-. X1 = ------ = 52.21
0.7Fy
J*c
-. X2 = ------ = 2.20
Syy*h0
-. Lr = 1.95*rts*X1 * SQRT[ X2 +SQRT[ X2^2 + 6.76*(1/X1)^2 ] ] = 5.31 m.

( ). Calculate nominal flexural strength for Lateral-torsional buckling (LTB).

[ AISC(15th) Specification F2.2 (F2-3), (F2-4) ]
-. Lb > Lr
Cb*Pi^2*Es [ J*c [ Lb ]^2 ]
-. Fcr = ---------- * SQRT[ 1+0.078*------ [ --- ] ] = 150492.3974 KPa.
(Lb/rts)^2 [ Syy*h0 [ rts ] ]
-. Mn = Fcr*Sx = 145.07 kN-m.
-. Mn.LTB = MIN [ Mn, Mp ] = 145.07 kN-m.

( ). Compute flexural strength about major axis (phiMny).

-. Mny = MIN[ Mn.Y, Mn.LTB ] = 145.07 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMny = phi*Mny = 130.57 kN-m.

( ). Check ratio of flexural strength (Muy/phiMny).

Muy 76.70
-. -------- = --------------- = 0.587 < 1.000 ---> O.K.
phiMny 130.57

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:19
http://www.MidasUser.com
Gen 2021 -5/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0010 m^3.
-. Syt = 0.0010 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 4.43 < Lambda_p = 10.79 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F6.1 (F6-1) ]
-. Mn.Y = Mp = MIN[ Fy*Zzz, 1.6*Fy*Szz ] = 34.83 kN-m.

--------------------------------------------------------------------------
[*] Check Flange Local Buckling (FLB).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Flange local buckling (FLB).

-. COMPACT flange ---> the limit state of flange local buckling is not applied.

( ). Compute flexural strength about minor axis (phiMnz).

-. Mnz = Mn.Y = 34.83 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMnz = phi*Mnz = 31.35 kN-m.

( ). Check ratio of flexural strength (Muz/phiMnz).

Muz 0.00
-. -------- = --------------- = 0.000 < 1.000 ---> O.K.
phiMnz 31.35

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:19
http://www.MidasUser.com
Gen 2021 -6/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Check interaction ratio of combined strength.

[ AISC(15th) Specification H1.1(b) ]
-. Pr/Pc < 0.20 ---> Formula(H1-1b)
Pr [ Mry Mrz ]
-. ComRat = ------ + [ ----- + ----- ]
2*Pc [ Mcy Mcz ]
= 0.000 + [ 0.587 + 0.000 ]
= 0.587 < 1.000 ---> O.K.

( ). Calculate shear strength coefficient (Cv1).

[ AISC(15th) Specification G2.1 (G2-2) ]
-. for Rolled H-Shape members.
-. h/tw = 21.743 < 2.24*SQRT[Es/Fy] = 63.576
-. Cv1 = 1.00

( ). Calculate shear strength in local-z direction (phiVnz).

-. Aw = 5.04e-03 m^2.
-. Vn = 0.6*Fy*Aw*Cv1 = 750.5911 kN.
-. for webs of rolled H-shape members with h/tw < 2.24*SQRT[Es/Fy].
-. Resistance factor for shear : phi = 1.00
-. phiVnz = phi*Vn = 750.59 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 2, POS = I )
-. Applied shear force : Vuz = 71.98 kN.
Vuz 71.98
-. -------- = --------------- = 0.096 < 1.000 ---> O.K.
phiVnz 750.59

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:19
http://www.MidasUser.com
Gen 2021 -7/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:17
http://www.MidasUser.com
Gen 2021 -1/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

25 1 DL( 0.900) + RS-M(RS)(-1.000)

26 1 DL( 0.900) + RS-O(RS)(-1.000)
--------------------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:17
http://www.MidasUser.com
Gen 2021 -2/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. PROJECT :
*. MEMBER NO = 163, ELEMENT TYPE = Beam
*. LOADCOMB NO = 8, MATERIAL NO = 1, SECTION NO = 37
*. UNIT SYSTEM : kN, m

*. SECTION PROPERTIES : Designation = I 40c

Shape = I - Section. (Rolled)
Depth = 0.400, Top F Width = 0.146, Bot.F Width = 0.146
Web Thick = 0.014, Top F Thick = 0.017, Bot.F Thick = 0.017

Area = 1.02070e-02, Asy = 3.21200e-03, Asz = 5.80000e-03

Ybar = 7.30000e-02, Zbar = 2.00000e-01, Qyb = 4.86931e-02, Qzb = 2.66450e-03
Syy = 1.19240e-03, Szz = 9.97000e-05, Zyy = 1.41210e-03, Zzz = 1.95147e-04
Iyy = 2.38470e-04, Izz = 7.27500e-06, Iyz = 0.00000e+00
ry = 1.52900e-01, rz = 2.67000e-02
J = 8.26949e-07, Cwp = 2.67488e-07

*. DESIGN PARAMETERS FOR STRENGTH EVALUATION :

Ly = 2.98333e+00, Lz = 2.98333e+00, Lu = 2.98333e+00
Ky = 1.00000e+00, Kz = 1.00000e+00

*. MATERIAL PROPERTIES :
Fy = 2.48211e+05, Es = 1.99948e+08, MATERIAL NAME = A36

( ). Compute moment magnification factors(B1y,B1z).

-. If tension or bending member.
-. Assumed B1y = 1.00
-. Assumed B1z = 1.00

( ). Magnification factors for sidesway moments(B2y,B2z).

-. B2y = 1.00 (Default value)
-. B2z = 1.00 (Default value)

( ). Given factored axial forces and moments at <1/4>.

----------------------------------------------------------------
Load Case Pa My Mz
----------------------------------------------------------------
DL 0.00 26.03 0.00
LL 0.00 12.64 0.00
DL+LL 0.00 38.67 0.00
OTHER CASES 0.00 14.47 0.00
----------------------------------------------------------------
TOTAL 0.00 53.15 0.00
----------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:17
http://www.MidasUser.com
Gen 2021 -3/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Compute magnified moments.

-. Muy = B1y*My(DL+LL) + B2y*My(OTHERS) = 53.15 kN-m.
-. Muz = B1z*Mz(DL+LL) + B2z*Mz(OTHERS) = 0.00 kN-m.

( ). Check slenderness ratio of axial tension member (L/r).

[ AISC(15th) Specification D1. ]
-. L/r = 111.7 < 300.0 ---> O.K.

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0012 m^3.
-. Syt = 0.0012 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Calculate limiting width-thickness ratio of web for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 3.76*SQRT[Es/Fy] = 106.72
-. Lambda_r = 5.70*SQRT[Es/Fy] = 161.78

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 4.42 < Lambda_p = 10.79 ---> COMPACT.

( ). Check width-thickness ratio of web (DTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. DTR = 23.59 < Lambda_p = 106.72 ---> COMPACT.

( ). Calculate lateral-torsional buckling modification factor (Cb).

[ AISC(15th) Specification F1.(2) (F1-1) ]
-. Cb = 1.000 (User defined or default value)

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:17
http://www.MidasUser.com
Gen 2021 -4/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F2.1 (F2-1) ]
-. Mn.Y = Mp = Fy*Zyy = 350.50 kN-m.

--------------------------------------------------------------------------
[*] Check Lateral-Torsional Buckling (LTB).
--------------------------------------------------------------------------

( ). Compute limiting laterally unbraced length for the limit state of yielding (Lp).
[ AISC(15th) Specification F2.2 (F2-5) ]
-. Lp = 1.76*rz*SQRT[Es/Fy] = 1.33 m.

( ). Compute laterally unbraced length for the limit state of inelastic lateral-
torsional buckling (Lr).
[ AISC(15th) Specification F2.2 (F2-6) ]
[ SQRT[Rzz*Cw] ]
-. rts = SQRT[ ------------ ] = 0.03 m.
[ Syy ]
-. c = 1.00 (for a doubly symmetry H-Shape)
-. h0 = H - 0.5*(tf1+tf2) = 0.38 m. (distance between the flange centroid)
Es
-. X1 = ------ = 48.94
0.7Fy
J*c
-. X2 = ------ = 2.56
Syy*h0
-. Lr = 1.95*rts*X1 * SQRT[ X2 +SQRT[ X2^2 + 6.76*(1/X1)^2 ] ] = 5.26 m.

( ). Calculate nominal flexural strength for Lateral-torsional buckling (LTB).

[ AISC(15th) Specification F2.2 (F2-2) ]
-. Lp < Lb < Lr.
[ Lb-Lp ]
-. Mn = Cb *[ Mp - (Mp-0.7*Fy*Syy) * ------- ] = 290.33 kN-m.
[ Lr-Lp ]
-. Mn.LTB = MIN [ Mn, Mp ] = 290.33 kN-m.

( ). Compute flexural strength about major axis (phiMny).

-. Mny = MIN[ Mn.Y, Mn.LTB ] = 290.33 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMny = phi*Mny = 261.30 kN-m.

( ). Check ratio of flexural strength (Muy/phiMny).

Muy 53.15
-. -------- = --------------- = 0.203 < 1.000 ---> O.K.
phiMny 261.30

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:17
http://www.MidasUser.com
Gen 2021 -5/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0012 m^3.
-. Syt = 0.0012 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 4.42 < Lambda_p = 10.79 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F6.1 (F6-1) ]
-. Mn.Y = Mp = MIN[ Fy*Zzz, 1.6*Fy*Szz ] = 39.59 kN-m.

--------------------------------------------------------------------------
[*] Check Flange Local Buckling (FLB).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Flange local buckling (FLB).

-. COMPACT flange ---> the limit state of flange local buckling is not applied.

( ). Compute flexural strength about minor axis (phiMnz).

-. Mnz = Mn.Y = 39.59 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMnz = phi*Mnz = 35.64 kN-m.

( ). Check ratio of flexural strength (Muz/phiMnz).

Muz 0.00
-. -------- = --------------- = 0.000 < 1.000 ---> O.K.
phiMnz 35.64

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:17
http://www.MidasUser.com
Gen 2021 -6/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Check interaction ratio of combined strength.

[ AISC(15th) Specification H1.1(b) ]
-. Pr/Pc < 0.20 ---> Formula(H1-1b)
Pr [ Mry Mrz ]
-. ComRat = ------ + [ ----- + ----- ]
2*Pc [ Mcy Mcz ]
= 0.000 + [ 0.203 + 0.000 ]
= 0.203 < 1.000 ---> O.K.

( ). Calculate shear strength coefficient (Cv1).

[ AISC(15th) Specification G2.1 (G2-2) ]
-. for Rolled H-Shape members.
-. h/tw = 23.586 < 2.24*SQRT[Es/Fy] = 63.576
-. Cv1 = 1.00

( ). Calculate shear strength in local-z direction (phiVnz).

-. Aw = 5.80e-03 m^2.
-. Vn = 0.6*Fy*Aw*Cv1 = 863.7755 kN.
-. for webs of rolled H-shape members with h/tw < 2.24*SQRT[Es/Fy].
-. Resistance factor for shear : phi = 1.00
-. phiVnz = phi*Vn = 863.78 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 2, POS = J )
-. Applied shear force : Vuz = 32.54 kN.
Vuz 32.54
-. -------- = --------------- = 0.038 < 1.000 ---> O.K.
phiVnz 863.78

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:17
http://www.MidasUser.com
Gen 2021 -7/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -1/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

25 1 DL( 0.900) + RS-M(RS)(-1.000)

26 1 DL( 0.900) + RS-O(RS)(-1.000)
--------------------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -2/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. PROJECT :
*. MEMBER NO = 45, ELEMENT TYPE = Beam
*. LOADCOMB NO = 8, MATERIAL NO = 1, SECTION NO = 31
*. UNIT SYSTEM : kN, m

*. SECTION PROPERTIES : Designation = I 45b

Shape = I - Section. (Rolled)
Depth = 0.450, Top F Width = 0.152, Bot.F Width = 0.152
Web Thick = 0.014, Top F Thick = 0.018, Bot.F Thick = 0.018

Area = 1.11400e-02, Asy = 3.64800e-03, Asz = 6.07500e-03

Ybar = 7.60000e-02, Zbar = 2.25000e-01, Qyb = 6.52005e-02, Qzb = 2.88800e-03
Syy = 1.50040e-03, Szz = 1.17800e-04, Zyy = 1.76041e-03, Zzz = 2.26799e-04
Iyy = 3.37590e-04, Izz = 8.95400e-06, Iyz = 0.00000e+00
ry = 1.74100e-01, rz = 2.84000e-02
J = 9.45270e-07, Cwp = 4.17758e-07

*. DESIGN PARAMETERS FOR STRENGTH EVALUATION :

Ly = 6.00000e+00, Lz = 6.00000e+00, Lu = 6.00000e+00
Ky = 1.00000e+00, Kz = 1.00000e+00

*. MATERIAL PROPERTIES :
Fy = 2.48211e+05, Es = 1.99948e+08, MATERIAL NAME = A36

( ). Compute moment magnification factors(B1y,B1z).

-. If tension or bending member.
-. Assumed B1y = 1.00
-. Assumed B1z = 1.00

( ). Magnification factors for sidesway moments(B2y,B2z).

-. B2y = 1.00 (Default value)
-. B2z = 1.00 (Default value)

( ). Given factored axial forces and moments at <I>.

----------------------------------------------------------------
Load Case Pa My Mz
----------------------------------------------------------------
DL 0.00 -22.84 0.00
LL 0.00 -11.01 0.00
DL+LL 0.00 -33.85 0.00
OTHER CASES 0.00 -145.68 0.00
----------------------------------------------------------------
TOTAL 0.00 -179.53 0.00
----------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -3/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Compute magnified moments.

-. Muy = B1y*My(DL+LL) + B2y*My(OTHERS) = -179.53 kN-m.
-. Muz = B1z*Mz(DL+LL) + B2z*Mz(OTHERS) = 0.00 kN-m.

( ). Check slenderness ratio of axial tension member (L/r).

[ AISC(15th) Specification D1. ]
-. L/r = 211.3 < 300.0 ---> O.K.

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0015 m^3.
-. Syt = 0.0015 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Calculate limiting width-thickness ratio of web for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 3.76*SQRT[Es/Fy] = 106.72
-. Lambda_r = 5.70*SQRT[Es/Fy] = 161.78

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 4.22 < Lambda_p = 10.79 ---> COMPACT.

( ). Check width-thickness ratio of web (DTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. DTR = 28.67 < Lambda_p = 106.72 ---> COMPACT.

( ). Calculate lateral-torsional buckling modification factor (Cb).

[ AISC(15th) Specification F1.(2) (F1-1) ]
-. Cb = 1.000 (User defined or default value)

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -4/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F2.1 (F2-1) ]
-. Mn.Y = Mp = Fy*Zyy = 436.95 kN-m.

--------------------------------------------------------------------------
[*] Check Lateral-Torsional Buckling (LTB).
--------------------------------------------------------------------------

( ). Compute limiting laterally unbraced length for the limit state of yielding (Lp).
[ AISC(15th) Specification F2.2 (F2-5) ]
-. Lp = 1.76*rz*SQRT[Es/Fy] = 1.42 m.

( ). Compute laterally unbraced length for the limit state of inelastic lateral-
torsional buckling (Lr).
[ AISC(15th) Specification F2.2 (F2-6) ]
[ SQRT[Rzz*Cw] ]
-. rts = SQRT[ ------------ ] = 0.04 m.
[ Syy ]
-. c = 1.00 (for a doubly symmetry H-Shape)
-. h0 = H - 0.5*(tf1+tf2) = 0.43 m. (distance between the flange centroid)
Es
-. X1 = ------ = 43.95
0.7Fy
J*c
-. X2 = ------ = 3.40
Syy*h0
-. Lr = 1.95*rts*X1 * SQRT[ X2 +SQRT[ X2^2 + 6.76*(1/X1)^2 ] ] = 5.19 m.

( ). Calculate nominal flexural strength for Lateral-torsional buckling (LTB).

[ AISC(15th) Specification F2.2 (F2-3), (F2-4) ]
-. Lb > Lr
Cb*Pi^2*Es [ J*c [ Lb ]^2 ]
-. Fcr = ---------- * SQRT[ 1+0.078*------ [ --- ] ] = 144411.9809 KPa.
(Lb/rts)^2 [ Syy*h0 [ rts ] ]
-. Mn = Fcr*Sx = 216.68 kN-m.
-. Mn.LTB = MIN [ Mn, Mp ] = 216.68 kN-m.

( ). Compute flexural strength about major axis (phiMny).

-. Mny = MIN[ Mn.Y, Mn.LTB ] = 216.68 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMny = phi*Mny = 195.01 kN-m.

( ). Check ratio of flexural strength (Muy/phiMny).

Muy 179.53
-. -------- = --------------- = 0.921 < 1.000 ---> O.K.
phiMny 195.01

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -5/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0015 m^3.
-. Syt = 0.0015 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 4.22 < Lambda_p = 10.79 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F6.1 (F6-1) ]
-. Mn.Y = Mp = MIN[ Fy*Zzz, 1.6*Fy*Szz ] = 46.78 kN-m.

--------------------------------------------------------------------------
[*] Check Flange Local Buckling (FLB).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Flange local buckling (FLB).

-. COMPACT flange ---> the limit state of flange local buckling is not applied.

( ). Compute flexural strength about minor axis (phiMnz).

-. Mnz = Mn.Y = 46.78 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMnz = phi*Mnz = 42.10 kN-m.

( ). Check ratio of flexural strength (Muz/phiMnz).

Muz 0.00
-. -------- = --------------- = 0.000 < 1.000 ---> O.K.
phiMnz 42.10

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -6/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Check interaction ratio of combined strength.

[ AISC(15th) Specification H1.1(b) ]
-. Pr/Pc < 0.20 ---> Formula(H1-1b)
Pr [ Mry Mrz ]
-. ComRat = ------ + [ ----- + ----- ]
2*Pc [ Mcy Mcz ]
= 0.000 + [ 0.921 + 0.000 ]
= 0.921 < 1.000 ---> O.K.

( ). Calculate shear strength coefficient (Cv1).

[ AISC(15th) Specification G2.1 (G2-2) ]
-. for Rolled H-Shape members.
-. h/tw = 28.667 < 2.24*SQRT[Es/Fy] = 63.576
-. Cv1 = 1.00

( ). Calculate shear strength in local-z direction (phiVnz).

-. Aw = 6.07e-03 m^2.
-. Vn = 0.6*Fy*Aw*Cv1 = 904.7303 kN.
-. for webs of rolled H-shape members with h/tw < 2.24*SQRT[Es/Fy].
-. Resistance factor for shear : phi = 1.00
-. phiVnz = phi*Vn = 904.73 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 8, POS = I )
-. Applied shear force : Vuz = 73.70 kN.
Vuz 73.70
-. -------- = --------------- = 0.081 < 1.000 ---> O.K.
phiVnz 904.73

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:15
http://www.MidasUser.com
Gen 2021 -7/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:20
http://www.MidasUser.com
Gen 2021 -1/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

25 1 DL( 0.900) + RS-M(RS)(-1.000)

26 1 DL( 0.900) + RS-O(RS)(-1.000)
--------------------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:20
http://www.MidasUser.com
Gen 2021 -2/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. PROJECT :
*. MEMBER NO = 743, ELEMENT TYPE = Beam
*. LOADCOMB NO = 13, MATERIAL NO = 1, SECTION NO = 32
*. UNIT SYSTEM : kN, m

*. SECTION PROPERTIES : Designation = HM 488x300x11/18

Shape = I - Section. (Rolled)
Depth = 0.488, Top F Width = 0.300, Bot.F Width = 0.300
Web Thick = 0.011, Top F Thick = 0.018, Bot.F Thick = 0.018

Area = 1.59190e-02, Asy = 7.20000e-03, Asz = 5.36800e-03

Ybar = 1.50000e-01, Zbar = 2.44000e-01, Qyb = 1.40902e-01, Qzb = 1.12500e-02
Syy = 2.78300e-03, Szz = 5.40400e-04, Zyy = 3.09984e-03, Zzz = 8.23673e-04
Iyy = 6.79160e-04, Izz = 8.10600e-05, Iyz = 0.00000e+00
ry = 2.06600e-01, rz = 7.14000e-02
J = 1.37492e-06, Cwp = 4.47654e-06

*. DESIGN PARAMETERS FOR STRENGTH EVALUATION :

Ly = 1.14580e+01, Lz = 1.14580e+01, Lu = 1.14580e+01
Ky = 1.00000e+00, Kz = 1.00000e+00

*. MATERIAL PROPERTIES :
Fy = 2.48211e+05, Es = 1.99948e+08, MATERIAL NAME = A36

( ). Compute moment magnification factors(B1y,B1z).

-. If tension or bending member.
-. Assumed B1y = 1.00
-. Assumed B1z = 1.00

( ). Magnification factors for sidesway moments(B2y,B2z).

-. B2y = 1.00 (Default value)
-. B2z = 1.00 (Default value)

( ). Given factored axial forces and moments at <J>.

----------------------------------------------------------------
Load Case Pa My Mz
----------------------------------------------------------------
DL 0.00 -16.22 0.00
LL 0.00 -0.65 0.00
DL+LL 0.00 -16.87 0.00
OTHER CASES 0.00 -22.09 0.00
----------------------------------------------------------------
TOTAL 0.00 -38.96 0.00
----------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:20
http://www.MidasUser.com
Gen 2021 -3/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Compute magnified moments.

-. Muy = B1y*My(DL+LL) + B2y*My(OTHERS) = -38.96 kN-m.
-. Muz = B1z*Mz(DL+LL) + B2z*Mz(OTHERS) = 0.00 kN-m.

( ). Check slenderness ratio of axial tension member (L/r).

[ AISC(15th) Specification D1. ]
-. L/r = 160.5 < 300.0 ---> O.K.

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0028 m^3.
-. Syt = 0.0028 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Calculate limiting width-thickness ratio of web for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 3.76*SQRT[Es/Fy] = 106.72
-. Lambda_r = 5.70*SQRT[Es/Fy] = 161.78

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 8.33 < Lambda_p = 10.79 ---> COMPACT.

( ). Check width-thickness ratio of web (DTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. DTR = 38.73 < Lambda_p = 106.72 ---> COMPACT.

( ). Calculate lateral-torsional buckling modification factor (Cb).

[ AISC(15th) Specification F1.(2) (F1-1) ]
-. Cb = 1.000 (User defined or default value)

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:20
http://www.MidasUser.com
Gen 2021 -4/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F2.1 (F2-1) ]
-. Mn.Y = Mp = Fy*Zyy = 769.41 kN-m.

--------------------------------------------------------------------------
[*] Check Lateral-Torsional Buckling (LTB).
--------------------------------------------------------------------------

( ). Compute limiting laterally unbraced length for the limit state of yielding (Lp).
[ AISC(15th) Specification F2.2 (F2-5) ]
-. Lp = 1.76*rz*SQRT[Es/Fy] = 3.57 m.

( ). Compute laterally unbraced length for the limit state of inelastic lateral-
torsional buckling (Lr).
[ AISC(15th) Specification F2.2 (F2-6) ]
[ SQRT[Rzz*Cw] ]
-. rts = SQRT[ ------------ ] = 0.08 m.
[ Syy ]
-. c = 1.00 (for a doubly symmetry H-Shape)
-. h0 = H - 0.5*(tf1+tf2) = 0.47 m. (distance between the flange centroid)
Es
-. X1 = ------ = 37.31
0.7Fy
J*c
-. X2 = ------ = 5.62
Syy*h0
-. Lr = 1.95*rts*X1 * SQRT[ X2 +SQRT[ X2^2 + 6.76*(1/X1)^2 ] ] = 11.05 m.

( ). Calculate nominal flexural strength for Lateral-torsional buckling (LTB).

[ AISC(15th) Specification F2.2 (F2-3), (F2-4) ]
-. Lb > Lr
Cb*Pi^2*Es [ J*c [ Lb ]^2 ]
-. Fcr = ---------- * SQRT[ 1+0.078*------ [ --- ] ] = 165023.8143 KPa.
(Lb/rts)^2 [ Syy*h0 [ rts ] ]
-. Mn = Fcr*Sx = 459.26 kN-m.
-. Mn.LTB = MIN [ Mn, Mp ] = 459.26 kN-m.

( ). Compute flexural strength about major axis (phiMny).

-. Mny = MIN[ Mn.Y, Mn.LTB ] = 459.26 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMny = phi*Mny = 413.34 kN-m.

( ). Check ratio of flexural strength (Muy/phiMny).

Muy 38.96
-. -------- = --------------- = 0.094 < 1.000 ---> O.K.
phiMny 413.34

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:20
http://www.MidasUser.com
Gen 2021 -5/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0028 m^3.
-. Syt = 0.0028 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 8.33 < Lambda_p = 10.79 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F6.1 (F6-1) ]
-. Mn.Y = Mp = MIN[ Fy*Zzz, 1.6*Fy*Szz ] = 204.44 kN-m.

--------------------------------------------------------------------------
[*] Check Flange Local Buckling (FLB).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Flange local buckling (FLB).

-. COMPACT flange ---> the limit state of flange local buckling is not applied.

( ). Compute flexural strength about minor axis (phiMnz).

-. Mnz = Mn.Y = 204.44 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMnz = phi*Mnz = 184.00 kN-m.

( ). Check ratio of flexural strength (Muz/phiMnz).

Muz 0.00
-. -------- = --------------- = 0.000 < 1.000 ---> O.K.
phiMnz 184.00

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:20
http://www.MidasUser.com
Gen 2021 -6/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Check interaction ratio of combined strength.

[ AISC(15th) Specification H1.1(b) ]
-. Pr/Pc < 0.20 ---> Formula(H1-1b)
Pr [ Mry Mrz ]
-. ComRat = ------ + [ ----- + ----- ]
2*Pc [ Mcy Mcz ]
= 0.000 + [ 0.094 + 0.000 ]
= 0.094 < 1.000 ---> O.K.

( ). Calculate shear strength coefficient (Cv1).

[ AISC(15th) Specification G2.1 (G2-2) ]
-. for Rolled H-Shape members.
-. h/tw = 38.727 < 2.24*SQRT[Es/Fy] = 63.576
-. Cv1 = 1.00

( ). Calculate shear strength in local-z direction (phiVnz).

-. Aw = 5.37e-03 m^2.
-. Vn = 0.6*Fy*Aw*Cv1 = 799.4391 kN.
-. for webs of rolled H-shape members with h/tw < 2.24*SQRT[Es/Fy].
-. Resistance factor for shear : phi = 1.00
-. phiVnz = phi*Vn = 799.44 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 11, POS = J )
-. Applied shear force : Vuz = 12.41 kN.
Vuz 12.41
-. -------- = --------------- = 0.016 < 1.000 ---> O.K.
phiVnz 799.44

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:20
http://www.MidasUser.com
Gen 2021 -7/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:16
http://www.MidasUser.com
Gen 2021 -1/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

25 1 DL( 0.900) + RS-M(RS)(-1.000)

26 1 DL( 0.900) + RS-O(RS)(-1.000)
--------------------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:16
http://www.MidasUser.com
Gen 2021 -2/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

*. PROJECT :
*. MEMBER NO = 69, ELEMENT TYPE = Beam
*. LOADCOMB NO = 8, MATERIAL NO = 1, SECTION NO = 36
*. UNIT SYSTEM : kN, m

*. SECTION PROPERTIES : Designation = HM 588x300x12/20

Shape = I - Section. (Rolled)
Depth = 0.588, Top F Width = 0.300, Bot.F Width = 0.300
Web Thick = 0.012, Top F Thick = 0.020, Bot.F Thick = 0.020

Area = 1.87210e-02, Asy = 8.00000e-03, Asz = 7.05600e-03

Ybar = 1.50000e-01, Zbar = 2.94000e-01, Qyb = 1.79538e-01, Qzb = 1.12500e-02
Syy = 3.83800e-03, Szz = 6.00600e-04, Zyy = 4.30891e-03, Zzz = 9.19728e-04
Iyy = 1.12827e-03, Izz = 9.00900e-05, Iyz = 0.00000e+00
ry = 2.45500e-01, rz = 6.94000e-02
J = 1.92717e-06, Cwp = 7.26630e-06

*. DESIGN PARAMETERS FOR STRENGTH EVALUATION :

Ly = 1.00000e+00, Lz = 1.00000e+00, Lu = 1.00000e+00
Ky = 1.00000e+00, Kz = 1.00000e+00

*. MATERIAL PROPERTIES :
Fy = 2.48211e+05, Es = 1.99948e+08, MATERIAL NAME = A36

( ). Compute moment magnification factors(B1y,B1z).

-. If tension or bending member.
-. Assumed B1y = 1.00
-. Assumed B1z = 1.00

( ). Magnification factors for sidesway moments(B2y,B2z).

-. B2y = 1.00 (Default value)
-. B2z = 1.00 (Default value)

( ). Given factored axial forces and moments at <I>.

----------------------------------------------------------------
Load Case Pa My Mz
----------------------------------------------------------------
DL 0.00 -15.12 0.00
LL 0.00 -6.78 0.00
DL+LL 0.00 -21.90 0.00
OTHER CASES 0.00 -13.99 0.00
----------------------------------------------------------------
TOTAL 0.00 -35.89 0.00
----------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:16
http://www.MidasUser.com
Gen 2021 -3/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Compute magnified moments.

-. Muy = B1y*My(DL+LL) + B2y*My(OTHERS) = -35.89 kN-m.
-. Muz = B1z*Mz(DL+LL) + B2z*Mz(OTHERS) = 0.00 kN-m.

( ). Check slenderness ratio of axial tension member (L/r).

[ AISC(15th) Specification D1. ]
-. L/r = 14.4 < 300.0 ---> O.K.

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0038 m^3.
-. Syt = 0.0038 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Calculate limiting width-thickness ratio of web for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 3.76*SQRT[Es/Fy] = 106.72
-. Lambda_r = 5.70*SQRT[Es/Fy] = 161.78

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 7.50 < Lambda_p = 10.79 ---> COMPACT.

( ). Check width-thickness ratio of web (DTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. DTR = 43.50 < Lambda_p = 106.72 ---> COMPACT.

( ). Calculate lateral-torsional buckling modification factor (Cb).

[ AISC(15th) Specification F1.(2) (F1-1) ]
-. Cb = 1.000 (User defined or default value)

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:16
http://www.MidasUser.com
Gen 2021 -4/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F2.1 (F2-1) ]
-. Mn.Y = Mp = Fy*Zyy = 1069.52 kN-m.

--------------------------------------------------------------------------
[*] Check Lateral-Torsional Buckling (LTB).
--------------------------------------------------------------------------

( ). Compute limiting laterally unbraced length for the limit state of yielding (Lp).
[ AISC(15th) Specification F2.2 (F2-5) ]
-. Lp = 1.76*rz*SQRT[Es/Fy] = 3.47 m.

( ). Calculate nominal flexural strength for Lateral-torsional buckling (LTB).

-. Lb < Lp ---> Lateral-torsional buckling is not applied.

( ). Compute flexural strength about major axis (phiMny).

-. Mny = Mn.Y = 1069.52 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMny = phi*Mny = 962.57 kN-m.

( ). Check ratio of flexural strength (Muy/phiMny).

Muy 35.89
-. -------- = --------------- = 0.037 < 1.000 ---> O.K.
phiMny 962.57

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0038 m^3.
-. Syt = 0.0038 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 7.50 < Lambda_p = 10.79 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:16
http://www.MidasUser.com
Gen 2021 -5/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F6.1 (F6-1) ]
-. Mn.Y = Mp = MIN[ Fy*Zzz, 1.6*Fy*Szz ] = 228.29 kN-m.

--------------------------------------------------------------------------
[*] Check Flange Local Buckling (FLB).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Flange local buckling (FLB).

-. COMPACT flange ---> the limit state of flange local buckling is not applied.

( ). Compute flexural strength about minor axis (phiMnz).

-. Mnz = Mn.Y = 228.29 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMnz = phi*Mnz = 205.46 kN-m.

( ). Check ratio of flexural strength (Muz/phiMnz).

Muz 0.00
-. -------- = --------------- = 0.000 < 1.000 ---> O.K.
phiMnz 205.46

( ). Check interaction ratio of combined strength.

[ AISC(15th) Specification H1.1(b) ]
-. Pr/Pc < 0.20 ---> Formula(H1-1b)
Pr [ Mry Mrz ]
-. ComRat = ------ + [ ----- + ----- ]
2*Pc [ Mcy Mcz ]
= 0.000 + [ 0.037 + 0.000 ]
= 0.037 < 1.000 ---> O.K.

( ). Calculate shear strength coefficient (Cv1).

[ AISC(15th) Specification G2.1 (G2-2) ]
-. for Rolled H-Shape members.
-. h/tw = 43.500 < 2.24*SQRT[Es/Fy] = 63.576
-. Cv1 = 1.00

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:16
http://www.MidasUser.com
Gen 2021 -6/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China.acs

( ). Calculate shear strength in local-z direction (phiVnz).

-. Aw = 7.06e-03 m^2.
-. Vn = 0.6*Fy*Aw*Cv1 = 1050.8275 kN.
-. for webs of rolled H-shape members with h/tw < 2.24*SQRT[Es/Fy].
-. Resistance factor for shear : phi = 1.00
-. phiVnz = phi*Vn = 1050.83 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 8, POS = I )
-. Applied shear force : Vuz = 38.98 kN.
Vuz 38.98
-. -------- = --------------- = 0.037 < 1.000 ---> O.K.
phiVnz 1050.83

Modeling, Integrated Design & Analysis Software Print Date/Time : 05/21/2025 20:16
http://www.MidasUser.com
Gen 2021 -7/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:05
http://www.MidasUser.com
Gen 2021 -1/6-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

*. PROJECT :
*. MEMBER NO = 528, ELEMENT TYPE = Beam
*. LOADCOMB NO = 2, MATERIAL NO = 1, SECTION NO = 2
*. UNIT SYSTEM : kN, m

*. SECTION PROPERTIES : Designation = RAFTER-2L1X1X1/4

Shape = 2L - Section. (Built-up)
Depth = 0.025, Flg Width = 0.025, BTB Spacing = 0.000
Web Thick = 0.006, Flg Thick = 0.006

Area = 5.64515e-04, Asy = 2.15053e-04, Asz = 2.15053e-04

Ybar = 2.54000e-02, Zbar = 1.67821e-02, Qyb = 1.40820e-04, Qzb = 3.22580e-04
Syy = 1.82924e-06, Szz = 2.85920e-06, Zyy = 3.29662e-06, Zzz = 4.86491e-06
Iyy = 3.06986e-08, Izz = 7.26237e-08, Iyz = 0.00000e+00
ry = 7.37431e-03, rz = 1.13423e-02
J = 1.42728e-08, Cwp = 2.54502e-13

*. DESIGN PARAMETERS FOR STRENGTH EVALUATION :

Ly = 4.14384e-01, Lz = 4.14384e-01, Lu = 4.14384e-01
Ky = 1.00000e+00, Kz = 1.00000e+00

*. MATERIAL PROPERTIES :
Fy = 2.48211e+05, Es = 1.99948e+08, MATERIAL NAME = A36

( ). Compute moment magnification factors(B1y,B1z).

-. If tension or bending member.
-. Assumed B1y = 1.00
-. Assumed B1z = 1.00

( ). Magnification factors for sidesway moments(B2y,B2z).

-. B2y = 1.00 (Default value)
-. B2z = 1.00 (Default value)

( ). Given factored axial forces and moments at <I>.

----------------------------------------------------------------
Load Case Pa My Mz
----------------------------------------------------------------
DL 20.71 -0.07 -1.33e-03
LL 26.64 -0.09 -1.89e-03
DL+LL 47.36 -0.16 -3.22e-03
OTHER CASES 0.00 0.00 0.00
----------------------------------------------------------------
TOTAL 47.36 -0.16 -3.22e-03
----------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:05
http://www.MidasUser.com
Gen 2021 -2/6-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Compute magnified moments.

-. Muy = B1y*My(DL+LL) + B2y*My(OTHERS) = -0.16 kN-m.
-. Muz = B1z*Mz(DL+LL) + B2z*Mz(OTHERS) = -3.22e-03 kN-m.

( ). Check slenderness ratio of axial tension member (L/r).

[ AISC(15th) Specification D1. ]
-. L/r = 56.2 < 300.0 ---> O.K.

( ). Calculate axial tensile strength (phiPn).

[ AISC(15th) Specification D2. ]
-. Resistance factor for tension : phi = 0.90
-. phiPn = phi*Area*Fy = 126.11 kN.

( ). Check ratio of axial strength (Pu/phiPn).

Pu 47.36
-. ------- = --------------- = 0.376 < 1.000 ---> O.K.
phiPn 126.11

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 4.00 < Lambda_p = 10.79 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y). -. For double angles with web
legs in compression
-. Mn.Y = 1.5*My = 0.68 kN-m.

--------------------------------------------------------------------------
[*] Check Lateral-Torsional Buckling (LTB).
--------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:05
http://www.MidasUser.com
Gen 2021 -3/6-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Compute limiting laterally unbraced length for the limit state of yielding (Lp).
[ AISC(15th) Specification F9.2 (F9-8) ]
-. Lp = 1.76*rz*SQRT[Es/Fy] = 0.57 m.

( ). Compute limiting laterally unbraced length for the limit state of

inelastic lateral torsional buckling (Lr).
[ AISC(15th) Specification F9.2 (F9-9) ]
-. Lp = 1.95*(Es/Fy)*(SQRT[Ryy*J]/Syy) *SQRT[2.36*(Fy/Es)*d*Syy/J + 1] = 27.78 m.

( ). Calculate nominal flexural strength for Lateral flexural buckling (LTB).

[ AISC(15th) SpecificationF9.2 (b) (2) ]
For stems and web legs in compression
-. When My/Mcr > 1.0
d [ Rzz ]
-. B = -2.3 * ---- * SQRT[ --- ] = -0.32
Lb [ J ]
-. Mcr = 1.95*Es/Lb * SQRT[Rzz/J] * (B+SQRT[1+B^2]) = 22.15 kN-m.
-. Mn.LTB = (0.92 - 0.17*Mcr/My)*Mcr = 0.68 kN-m.

--------------------------------------------------------------------------
[*] Check Flange Local Buckling (FLB).
--------------------------------------------------------------------------

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 1.8292e-06 m^3.
-. Syt = 3.5622e-06 m^3.

( ). Calculate nominal flexural strength for Flexural local buckling (FLB).

[ AISC(15th) Specification F9.3 (a) ]
-. For compact sections, flange local buckling is not applied.

--------------------------------------------------------------------------
[*] Check Stem Local Buckling (SLB).
--------------------------------------------------------------------------

( ). Calculate limiting width-thickness ratio of stem for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.84*SQRT[Es/Fy] = 23.84
-. Lambda_r = 1.52*SQRT[Es/Fy] = 43.14

( ). Calculate nominal flexural strength for Local buckling of tee stems (SLB).
[ AISC(15th) Specification F9.4 (F9-16) ]
-. Fcr = Fy = 248211.3398 KPa.
-. Mn.SLB = Fcr * Syy = 0.45 kN-m.

( ). Compute flexural strength about major axis (phiMny).

-. Mny = MIN[ Mn.Y, Mn.LTB, Mn.SLB ] = 0.45 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMny = phi*Mny = 0.41 kN-m.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:05
http://www.MidasUser.com
Gen 2021 -4/6-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Check ratio of flexural strength (Muy/phiMny).

Muy 0.16
-. -------- = --------------- = 0.382 < 1.000 ---> O.K.
phiMny 0.41

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 4.00 < Lambda_p = 10.79 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y).

-. Fn = Fy = 248211.3398 KPa.
-. Mn = Fn*Szz = 0.71 kN-m.

( ). Compute flexural strength about minor axis (phiMnz).

-. Mnz = Mn.Y = 0.71 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMnz = phi*Mnz = 0.64 kN-m.

( ). Check ratio of flexural strength (Muz/phiMnz).

Muz 3.22e-03
-. -------- = --------------- = 0.005 < 1.000 ---> O.K.
phiMnz 0.64

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:05
http://www.MidasUser.com
Gen 2021 -5/6-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Check interaction ratio of combined strength.

[ AISC(15th) Specification H1.1(a) ]
-. Pr/Pc > 0.20 ---> Formula(H1-1a)
Pr 8 [ Mry Mrz ]
-. ComRat = ---- + --- [ ----- + ----- ]
Pc 9 [ Mcy Mcz ]
= 0.376 + (8/9)*[ 0.382 + 0.005 ]
= 0.720 < 1.000 ---> O.K.

( ). Calculate the web shear buckling coefficient (Cv2).

[ AISC(15th) Specification G2.2 (G2-9) ]
-. for webs of all other doubly/singly symmetric shapes and channels.
-. kv (web plate buckling coefficient) = 1.20
-. h/tw = 4.000< 1.10*SQRT[kv*Es/Fy] = 34.200
-. Cv2 = 1.00

( ). Calculate shear strength in local-y direction (phiVny).

-. Aw = 3.23e-04 m^2.
-. Vn = 0.6*Fy*Aw*Cv2 = 48.0408 kN.
-. Resistance factor for shear : phi = 0.90
-. phiVny = phi*Vn = 43.24 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 2, POS = J )
-. Applied shear force : Vuy = 0.01 kN.
Vuy 0.01
-. -------- = --------------- =2.917e-04 < 1.000 ---> O.K.
phiVny 43.24

( ). Calculate the web shear buckling coefficient (Cv2).

[ AISC(15th) Specification G2.2 (G2-9) ]
-. for webs of all other doubly/singly symmetric shapes and channels.
-. kv (web plate buckling coefficient) = 5.00
-. h/tw = 4.000< 1.10*SQRT[kv*Es/Fy] = 69.811
-. Cv2 = 1.00

( ). Calculate shear strength in local-z direction (phiVnz).

-. Aw = 3.23e-04 m^2.
-. Vn = 0.6*Fy*Aw*Cv2 = 48.0408 kN.
-. Resistance factor for shear : phi = 0.90
-. phiVnz = phi*Vn = 43.24 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 1, POS = I )
-. Applied shear force : Vuz = 0.05 kN.
Vuz 0.05
-. -------- = --------------- = 0.001 < 1.000 ---> O.K.
phiVnz 43.24

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:05
http://www.MidasUser.com
Gen 2021 -6/6-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:49
http://www.MidasUser.com
Gen 2021 -1/8-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

*. PROJECT :
*. MEMBER NO = 5, ELEMENT TYPE = Beam
*. LOADCOMB NO = 2, MATERIAL NO = 1, SECTION NO = 1
*. UNIT SYSTEM : kN, m

*. SECTION PROPERTIES : Designation = RAFTER-2L2X2X1/4, 2L2X2X1/4

Shape = 2L - Section. (Rolled)
Depth = 0.051, Flg Width = 0.051, BTB Spacing = 0.000
Web Thick = 0.006, Flg Thick = 0.006

Area = 1.21935e-03, Asy = 4.30107e-04, Asz = 4.30107e-04

Ybar = 5.08000e-02, Zbar = 3.59156e-02, Qyb = 6.44965e-04, Qzb = 1.29032e-03
Syy = 7.99689e-06, Szz = 1.10741e-05, Zyy = 1.44206e-05, Zzz = 6.14515e-05
Iyy = 2.88032e-07, Izz = 5.62563e-07, Iyz = 0.00000e+00
ry = 1.53670e-02, rz = 2.13868e-02
J = 4.11896e-08, Cwp = 2.78587e-12

*. DESIGN PARAMETERS FOR STRENGTH EVALUATION :

Ly = 3.94595e-01, Lz = 3.94595e-01, Lu = 3.94595e-01
Ky = 1.00000e+00, Kz = 1.00000e+00

*. MATERIAL PROPERTIES :
Fy = 2.48211e+05, Es = 1.99948e+08, MATERIAL NAME = A36

( ). Factored force/moments caused by unit load case.

*.Load combination ID = 2
-------------------------------------------------------------------------------
Load Case Pa Myi Myj Mzi Mzj
-------------------------------------------------------------------------------
DL -61.04 0.00 0.00 0.09 0.34
LL -77.53 0.00 0.00 0.13 0.48
DL+LL -138.56 0.00 0.00 0.22 0.81
OTHER CASES 0.00 0.00 0.00 0.00 0.00
-------------------------------------------------------------------------------
TOTAL -138.56 0.00 0.00 0.22 0.81
-------------------------------------------------------------------------------
*.Member end moments caused by gravity load(DL+LL).
My1G = 0.00, My2G = 0.00
Mz1G = 0.22, Mz2G = 0.81

( ). Compute coefficient assuming no lateral translation of the frame (Cmy, Cmz)

[ AISC(15th) Specification C2.1.1b. (C2-4) ]
-. Cmy = 1.000 (User defined or default value)
-. Cmz = 1.000 (User defined or default value)

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:49
http://www.MidasUser.com
Gen 2021 -2/8-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Compute moment magnification factors(B1y,B1z).

-. Pu = Pu(DL+LL) + Pu(WL(EL)) = 138.56 kN.
-. About major(Local-y) axis.
SLENy = Ky*Ly/ry = 25.68
Lambda = (SLENy/pi)*SQRT(Fy/Es) = 0.2880
Pey = (Area*Fy)/Lambda^2 = 3649.40 kN.
B1y = Cmy / (1-Pu/Pey) = 1.04
-. About minor(Local-z) axis.
SLENz = Kz*Lz/rz = 18.45
Lambda = (SLENz/pi)*SQRT(Fy/Es) = 0.2069
Pez = (Area*Fy)/Lambda^2 = 7068.63 kN.
B1z = Cmz / (1-Pu/Pez) = 1.02

( ). Magnification factors for sidesway moments(B2y,B2z).

-. B2y = 1.00 (Default value)
-. B2z = 1.00 (Default value)

( ). Given factored axial forces and moments at <J>.

----------------------------------------------------------------
Load Case Pa My Mz
----------------------------------------------------------------
DL -61.04 0.00 0.34
LL -77.53 0.00 0.48
DL+LL -138.56 0.00 0.81
OTHER CASES 0.00 0.00 0.00
----------------------------------------------------------------
TOTAL -138.56 0.00 0.81
----------------------------------------------------------------

( ). Compute magnified moments.

-. Muy = B1y*My(DL+LL) + B2y*My(OTHERS) = 0.00 kN-m.
-. Muz = B1z*Mz(DL+LL) + B2z*Mz(OTHERS) = 0.83 kN-m.

( ). Check slenderness ratio of axial compression member (KL/r).

[ AISC(15th) Specification E2. ]
-. KL/r = 25.7 < 200.0 ---> O.K.

( ). Check width-thickness ratio of legs of angle (BTR).

[ AISC(15th) Specification B4. <Table B4.1a> ]
-. Lambda_r = 0.45*SQRT[Es/Fy] = 12.77
-. BTR = bf/tf = 8.00 < Lambda_r ---> NON-SLENDER SECTION !

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:49
http://www.MidasUser.com
Gen 2021 -3/8-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Calculate Flexural Buckling Stress (Fcr1).

[ AISC(15th) Specification E3 ]
pi^2 * E
-. Fe = ----------- = 2992903.9573 KPa.
(Lc/r)^2
-. Lc/r = 25.678
-. 4.71 * SQRT[Es/Fy] = 133.681
-. Fy/Fe = 0.0829
-. When Lc/r < 4.71 * SQRT[Es/Fy]
-. Fcr1 = (0.658)^(Fy/Fe) * Fy = 239743.3095 KPa.

( ). Torsional and flexural-torsional buckling stress (Fcr2)

[ AISC(15th) Specification E4.(b) (E4-3) ]
-. Singly symmetric shape where z is the axis of symmetry
-. Gs = 7.7221e+07 KPa.
-. Kx = 1.00 (Conservatively taken value).
-. L = 0.395 m.
-. r0^2 = 8.347e-04 m^2/m.
-. H = 1 -(y0^2 + z0^2)/r0^2 = 0.836
-. Fez = Pi^2*Es/(Lcz/rz)^2 =5797038.8940 KPa.
-. Fex = [Pi^2*Es*Cwp/(Lcx)^2 + Gs*J]/(Area*r0^2) =3125146.4275 KPa.
-. Fe = (Fez+Fex)/(2*H)*[1-SQRT[1-(4*Fez*Fex*H/(Fez+Fex)^2)] ]
=2727175.3045 KPa.

-. Lc/r = 25.678
-. 4.71 * SQRT[Es/Fy] = 133.681
-. Fy/Fe = 0.0910

-. When Lc/r < 4.71 * SQRT[Es/Fy]

-. Fcr2 = (0.658)^(Fy/Fe) * Fy = 238933.8145 KPa.

( ). Calculate axial compressive strength (phiPn).

[ AISC(15th) Specification E1. ]
-. Fcr = 238933.8145 KPa.
-. Resistance factor for compression : phi = 0.90
-. phiPn = phi*Area*Fcr = 262.21 kN.

( ). Check ratio of axial strength (Pu/phiPn).

Pu 138.56
-. ------- = --------------- = 0.528 < 1.000 ---> O.K.
phiPn 262.21

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:49
http://www.MidasUser.com
Gen 2021 -4/8-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 8.00 < Lambda_p = 10.79 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y).

-. For tee stems and web in tension
-. Mn.Y = MIN[ Fy*Zyy, 1.6*My ] = 3.18 kN-m.

--------------------------------------------------------------------------
[*] Check Lateral-Torsional Buckling (LTB).
--------------------------------------------------------------------------

( ). Compute limiting laterally unbraced length for the limit state of yielding (Lp).
[ AISC(15th) Specification F9.2 (F9-8) ]
-. Lp = 1.76*rz*SQRT[Es/Fy] = 1.07 m.

( ). Compute limiting laterally unbraced length for the limit state of

inelastic lateral torsional buckling (Lr).
[ AISC(15th) Specification F9.2 (F9-9) ]
-. Lp = 1.95*(Es/Fy)*(SQRT[Ryy*J]/Syy) *SQRT[2.36*(Fy/Es)*d*Syy/J + 1] = 30.33 m.

( ). Calculate nominal flexural strength for Lateral flexural buckling (LTB).

[ AISC(15th) Specification F9.2 (a) (1) ]
For stems and web legs in tension
-. Lb < Lp ---> Lateral-torsional buckling is not applied.

--------------------------------------------------------------------------
[*] Check Flange Local Buckling (FLB).
--------------------------------------------------------------------------

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 1.9351e-05 m^3.
-. Syt = 8.0197e-06 m^3.

( ). Calculate nominal flexural strength for Flexural local buckling (FLB).

[ AISC(15th) Specification F9.3 (a) ]
-. For compact sections, flange local buckling is not applied.

( ). Compute flexural strength about major axis (phiMny).

-. Mny = Mn.Y = 3.18 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMny = phi*Mny = 2.86 kN-m.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:49
http://www.MidasUser.com
Gen 2021 -5/8-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Check ratio of flexural strength (Muy/phiMny).

Muy 0.00
-. -------- = --------------- = 0.000 < 1.000 ---> O.K.
phiMny 2.86

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 8.00 < Lambda_p = 10.79 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y).

-. Fn = Fy = 248211.3398 KPa.
-. Mn = Fn*Szz = 2.75 kN-m.

( ). Compute flexural strength about minor axis (phiMnz).

-. Mnz = Mn.Y = 2.75 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMnz = phi*Mnz = 2.47 kN-m.

( ). Check ratio of flexural strength (Muz/phiMnz).

Muz 0.83
-. -------- = --------------- = 0.334 < 1.000 ---> O.K.
phiMnz 2.47

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:49
http://www.MidasUser.com
Gen 2021 -6/8-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Check interaction ratio of combined strength.

[ AISC(15th) Specification H1.1(a) ]
-. Pr/Pc > 0.20 ---> Formula(H1-1a)
Pr 8 [ Mry Mrz ]
-. ComRat = ---- + --- [ ----- + ----- ]
Pc 9 [ Mcy Mcz ]
= 0.528 + (8/9)*[ 0.000 + 0.334 ]
= 0.826 < 1.000 ---> O.K.

( ). Calculate the web shear buckling coefficient (Cv2).

[ AISC(15th) Specification G2.2 (G2-9) ]
-. for webs of all other doubly/singly symmetric shapes and channels.
-. kv (web plate buckling coefficient) = 1.20
-. h/tw = 8.000< 1.10*SQRT[kv*Es/Fy] = 34.200
-. Cv2 = 1.00

( ). Calculate shear strength in local-y direction (phiVny).

-. Aw = 6.45e-04 m^2.
-. Vn = 0.6*Fy*Aw*Cv2 = 96.0816 kN.
-. Resistance factor for shear : phi = 0.90
-. phiVny = phi*Vn = 86.47 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 2, POS = J )
-. Applied shear force : Vuy = 1.50 kN.
Vuy 1.50
-. -------- = --------------- = 0.017 < 1.000 ---> O.K.
phiVny 86.47

( ). Calculate the web shear buckling coefficient (Cv2).

[ AISC(15th) Specification G2.2 (G2-9) ]
-. for webs of all other doubly/singly symmetric shapes and channels.
-. kv (web plate buckling coefficient) = 5.00
-. h/tw = 8.000< 1.10*SQRT[kv*Es/Fy] = 69.811
-. Cv2 = 1.00

( ). Calculate shear strength in local-z direction (phiVnz).

-. Aw = 6.45e-04 m^2.
-. Vn = 0.6*Fy*Aw*Cv2 = 96.0816 kN.
-. Resistance factor for shear : phi = 0.90
-. phiVnz = phi*Vn = 86.47 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 1, POS = J )
-. Applied shear force : Vuz = 0.03 kN.
Vuz 0.03
-. -------- = --------------- =3.003e-04 < 1.000 ---> O.K.
phiVnz 86.47

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:49
http://www.MidasUser.com
Gen 2021 -7/8-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

======================================================================================
[[[*]]] CHECK DEFLECTION.
======================================================================================

( ). Compute Maximum Deflection.

-. LCB = 5
-. DAF = 1.000 (Deflection Amplification Factor).
-. Position = 0.197m From i-end(Node 6).
-. Def = -5.595e-07 * DAF =-5.595e-07m (Global Z)
-. Def_Lim = 0.001m
Def < Def_Lim ---> O.K !

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:49
http://www.MidasUser.com
Gen 2021 -8/8-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

------------------------------------------------------------------------------------------
midas Gen - Cold Formed Steel Code Checking [ AISI-CFSD08 ] Gen 2021
==========================================================================================

+============================================================+
| MIDAS(Modeling, Integrated Design & Analysis Software) |
| midas Gen - Design & checking system for windows |
+============================================================+
| Cold Formed Steel Member Applicable Code Checking |
| Based On Eurocode3-1-3:06, AISI-CFSD08, AISI-CFSD86 |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| (c)SINCE 1989 |
+============================================================+
| MIDAS Information Technology Co.,Ltd. (MIDAS IT) |
| MIDAS IT Design Development Team |
+============================================================+
| HomePage : www.MidasUser.com |
+============================================================+
| Gen 2021 |
+============================================================+

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:14
http://www.MidasUser.com
Gen 2021 - 1 / 14 -
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

*. PROJECT :
*. MEMBER NO = 299, ELEMENT TYPE = Beam
*. LOADCOMB NO = 2, MATERIAL NO = 1, SECTION NO = 3
*. UNIT SYSTEM : kN, m

*. SECTION PROPERTIES : Designation = PURLINS-2''X6''X1.8mm

Shape = CC - Section. (Built-up)
Depth = 0.150, Width = 0.050, Lip Depth = 0.020
Thickness = 0.002, Fillet Radius = 1.000e-04

Area = 5.05950e-04, Asy = 1.71975e-04, Asz = 3.23115e-04

Ybar = 1.55686e-02, Zbar = 7.50000e-02, Qyb = 7.48618e-03, Qzb = 1.09475e-03
Syy = 2.28347e-05, Szz = 5.27810e-06, Zyy = 0.00000e+00, Zzz = 0.00000e+00
Iyy = 1.71260e-06, Izz = 1.81732e-07, Iyz = 0.00000e+00
ry = 5.81801e-02, rz = 1.89523e-02
J = 5.46426e-10, Cwp = 8.96299e-10

*. DESIGN PARAMETERS FOR STRENGTH EVALUATION :

Ly = 3.00000e+00, Lz = 3.00000e+00, Lu = 3.00000e+00
Ky = 1.00000e+00, Kz = 1.00000e+00

*. MATERIAL PROPERTIES :
Fy = 2.48211e+05, Es = 1.99948e+08, MATERIAL NAME = A36

( ). Factored force/moments caused by unit load case.

*.Load combination ID = 2
-------------------------------------------------------------------------------
Load Case Pu Myi Myj Mzi Mzj
-------------------------------------------------------------------------------
DL -0.15 -0.07 -0.19 -1.54e-03 -1.54e-03
LL -0.14 -0.06 -0.24 -1.40e-03 -1.40e-03
DL+LL -0.29 -0.13 -0.43 -2.94e-03 -2.94e-03
OTHER CASES 0.00 0.00 0.00 0.00 0.00
-------------------------------------------------------------------------------
TOTAL -0.29 -0.13 -0.43 -2.94e-03 -2.94e-03
-------------------------------------------------------------------------------

======================================================================================
[[[*]]] CALCULATE FULL SECTION PRORERTIES.
======================================================================================

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:14
http://www.MidasUser.com
Gen 2021 - 2 / 14 -
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Calculate properties of sections with or without lips.

[ AISI-CFSD08 Calc. Section Properties III 3.3 ]
-. Alpha = 1.0000
-. r = R + t/2 = 0.0010 m.
-. a = H - (2*r+t) = 0.1462 m.
-. a_bar = H - t = 0.1482 m.
-. b = B - [r+t/2 + Alpha*(r+t/2)] = 0.0462 m.
-. b_bar = B - (t/2 + Alpha*t/2) = 0.0482 m.
-. c = Alpha*[C - (r+t/2)] = 0.0181 m.
-. c_bar = Alpha*(C - t/2) = 0.0191 m.
-. u = 1.57*r = 0.0016 m.

-. A = t{ a + 2b + 2c + Alpha(2c + 2u) } = 0.0005 m^2.

-. Iyy = (2*t) * { 0.0417*a^3 + b*(a/2+r)^2 + u*(a/2+0.637*r)^2) + 0.149*r^3 +
Alpha*[0.0833*c^3 + (c/4)*(a-c)^2 + u*(a/2+0.637*r)^2) + 0.149*r^3] }
= 1.7129e-06 m^4.
-. x_bar = (2*t/A) * { b*(b/2+r) + u*(0.363*r) + Alpha*[u*(b+1.637*r) + c*(b+2*r)] }
= 0.0147 m.
-. Izz = (2*t) * { b*(b/2+r)^2 + 0.0833*b^3 + 0.356*r^3 + Alpha*[c*(b+2*r)^2 +
u*(b+1.637*r)^2 + 0.149*r^3] } - A*x_bar^2
= 1.8163e-07 m^4.

-. m = b_bart/(12Iy) * { 6c_bara_bar^2 + 3b_bara_bar^2 - 8*c_bar^3 }

= 0.0238 m.
-. x0 = (-1)*(x_bar + m) = -0.0385 m.

-. Rxx = (t^3/3){ a + 2b + 2u + Alpha(2c + 2u) }

= 0.000000 m^4.
-. Cwp = (t^2/A)*{ (x_bar*A*a_bar^2/t) * [b_bar^2/3 + m^2 - m*b_bar] +
[A/(3*t)] * [m^2*a_bar^3 + b_bar^2*c_bar^2*(2*c_bar+3*a_bar)] -
(Iyy*m^2/t)*(2*a_bar + 4*c_bar) + (m*c_bar^2/3) * {8*b_bar^2*c_bar +
2*m*[2*c_bar*(c_bar-a_bar) + b_bar*(2*c_bar-3*a_bar)]} +
(b_bar^2*a_bar^2/6)*[(3*c_bar+b_bar)*(4*c_bar+a_bar) - 6*c_bar^2] +
m^2*a_bar^4/4 }
= 0.000000 m^6.

-. Beta_w = (-1)[0.0833(tx_bara_bar^3) + tx_bar^3a_bar] = -0.0000 m^5.

-. Beta_f = (t/2)*[(b_bar-x_bar)^4 - x_bar^4] +
(t*a_bar^2/4)*[(b_bar-x_bar)^2-x_bar^2] = 0.0000 m^5.
-. Beta_l = (2*c_bar*t)*(b_bar-x_bar)^3 + (2/3)*t*(b_bar-x_bar) *
[(a_bar/2)^3 - (a_bar/2-c_bar)^3] = 0.0000 m^5.
-. j = 1/(2*Izz)*(Beta_w + Beta_f + Beta_l) - x0 = 0.0780 m.
-. ry = SQRT( Iyy/A ) = 0.0582 m.
-. rz = SQRT( Izz/A ) = 0.0189 m.
-. r0 = SQRT[ ry^2 + rz^2 + x0^2 ] = 0.0723 m.
-. Beta = 1 - (x0/r0)^2 = 0.7168
*.Member end moments caused by gravity load(DL+LL).
My1G = 0.13, My2G = 0.43
Mz1G = 2.94e-03, Mz2G = 2.94e-03

( ). Compute equivalent moment factor (Cmy, Cmz).

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:14
http://www.MidasUser.com
Gen 2021 - 3 / 14 -
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

-. Cmy = 1.000 (User defined or default value)

-. Cmz = 1.000 (User defined or default value)

( ). Compute moment magnification factors(Alpha_y,Alpha_z).

-. Pu = Pu(DL+LL) + Pu(WL(EL)) = 0.29 kN.
-. About major(Local-y) axis.
Pey = (Pi^2*Es*Iyy) / (Ky*Ly)^2 = 375.58 kN.
Omega_c = 1.9200
Alpha_y = 1 - Omega_c*(Pu/Pey) = 1.00
-. About minor(Local-z) axis.
Pez = (Pi^2*Es*Izz) / (Kz*Lz)^2 = 39.83 kN.
Alpha_z = 1 - Omega_c*(Pu/Pez) = 0.99

( ). Given factored axial forces and moments at <1/2>.

----------------------------------------------------------------
Load Case Pu My Mz
----------------------------------------------------------------
DL -0.15 0.25 -1.54e-03
LL -0.14 0.25 -1.40e-03
DL+LL -0.29 0.51 -2.94e-03
OTHER CASES 0.00 0.00 0.00
----------------------------------------------------------------
TOTAL -0.29 0.51 -2.94e-03
----------------------------------------------------------------

( ). Compute magnified moments.

-. Muy = (Cmy/Alpha_y)*My(DL+LL) + My(OTHERS) = 0.51 kN-m.
-. Muz = (Cmz/Alpha_z)*Mz(DL+LL) + Mz(OTHERS) = -2.98e-03 kN-m.

( ). Factored max. shear forces.

-. Vuy = 0.00 kN.
-. Vuz = 0.10 kN.

( ). Check slenderness ratio of axial compression member (Kl/r).

[ AISI-CFSD08 Specification I C4 (d) ]
-. Kl/r = 158.3 < 200.0 ---> O.K.

======================================================================================
[[[*]]] DETERMINE ALLOWABLE CONCENTRATED LOAD (Pa).
======================================================================================

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:14
http://www.MidasUser.com
Gen 2021 - 4 / 14 -
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Calculate stress at effective section.

[ AISI-CFSD08 Specification I C4 Eq.C4.1-1~4 ]
-. Gs = Es / [ 2*(1+Por) ] =76903086.056 KPa.
-. sigma_ey = Pi^2*Es / (Ky*Ly/ry)^2 = 742342.357 KPa.
-. sigma_ez = Pi^2*Es / (Kz*Lz/rz)^2 = 78714.568 KPa.
-. Fe1 = sigma_ez = 78714.568 KPa.
-. sigma_t = {1/(A*r0^2)} * {Gs*Rxx + Pi^2*Es*Cwp/(Kt*Lt)^2} = 92126.588 KPa.
-. Fe2 = {1/(2*Beta)} * {(sigma_ey+sigma_t) - SQRT[
(sigma_ey+sigma_t)^2 - 4*Beta*sigma_ey*sigma_t]}= 88716.568 KPa.

-. Fe = MIN[ Fe1, Fe2 ] = 78714.568 KPa.

-. Lambda_c = SQRT[ Fy / Fe ] = 1.7758

-. In case of Lambda_c > 1.5
-. Fn = (0.877/Lambda_c^2)*Fy = 69032.676 KPa.
-. Omega_c = 1.800

< For web element >

[ AISI-CFSD08 Specification I B2.1 Eq.B2.1-1~4 ]
-. HTR = w/t = 81.22 < 200 ---> O.K.
-. k = 4.00
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/w)^2 = 109573.234 KPa.
-. Lambda = SQRT[ Fn / Fcr ] = 0.7937
-. In case of Lambda > 0.673
-. Rho = (1 - 0.22/Lambda)/Lambda = 0.9107
-. b = Rho*w = 0.133 m. (Partially effective).

< For flange elements >

[ AISI-CFSD08 Specification I B4 Eq.B2.1-1~5, Eq.B4.1-11 ]
-. HTR = w/t = 25.67
-. S = 1.28*SQRT[ Es/Fn ] = 68.89
-. Is = c^3*t*sin^2(rad) / 12 = 0.0000 m^4.
-. Ia1 = t^4*399*[(BTR/S)-0.328]^3 = 0.0000 m^4.
-. Ia2 = t^4*[115*(w/t)/S + 5] = 0.0000 m^4.
-. Ia = MIN[ Ia1 , Ia2 ] = 0.0000 m^4.
-. n = 0.4889
-. k = 3.09
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/w)^2 = 846409.498 KPa.
-. Lambda = SQRT[ Fn / Fcr ] = 0.2856
-. In case of Lambda < 0.673
-. b = 0.046 m. (Fully effective).

< For lip elements >

[ AISI-CFSD08 Specification I B4.2 Eq.B4.2-1~13 ]
-. HTR = d/t = 10.06 < 60 ---> O.K.
-. k = 0.43
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/d)^2 = 768511.798 KPa.
-. Lambda = SQRT[ Fn / Fcr ] = 0.2997
-. In case of Lambda < 0.673
-. ds = 0.018 m. (Fully effective).

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:14
http://www.MidasUser.com
Gen 2021 - 5 / 14 -
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Calculate allowable compression force (Pa).

[ AISI-CFSD08 Specification I C4 Eq.C4-1~4 ]
-. bWeb = 0.133 m.
-. bFlange = 0.046 m.
-. bLip = 0.018 m.
-. Ae = A - [(a-bWeb) + 2*(b-bFlange) + 2*(c-bLip)]*t = 4.824e-04 m^2.
-. Pn = Ae * Fn = 33.30 kN.
-. Pa = Pn / Omega_c = 18.50 kN.

( ). Check ratio of axial load (Pu/Pa).

Pu 0.29
-. ---- = --------------- = 0.016 < 1.000 ---> O.K.
Pa 18.50

======================================================================================
[[[*]]] DETERMINE ALLOWABLE CONCENTRATED LOAD (Pao, L=0).
======================================================================================

( ). Calculate stress at effective section.

[ AISI-CFSD08 Specification I C4 Eq.C4-1, Eq.C4-3~4 ]
-. Fe is infinity Since L is Zero
-. In case of Fe > Fy/2.
-. Fn = Fy = 248211.340 KPa.
-. Omega_c = 1.8 = 1.800

< For web element >

[ AISI-CFSD08 Specification I B2.1 Eq.B2.1-1~4 ]
-. HTR = w/t = 81.22 < 200 ---> O.K.
-. k = 4.00
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/w)^2 = 109573.234 KPa.
-. Lambda = SQRT[ Fn / Fcr ] = 1.5051
-. In case of Lambda > 0.673
-. Rho = (1 - 0.22/Lambda)/Lambda = 0.5673
-. b = Rho*w = 0.083 m. (Partially effective).

< For flange elements >

[ AISI-CFSD08 Specification I B4 Eq.B2.1-1~5, Eq.B4.1-11 ]
-. HTR = w/t = 25.67
-. S = 1.28*SQRT[ Es/Fn ] = 36.33
-. Is = c^3*t*sin^2(rad) / 12 = 0.0000 m^4.
-. Ia1 = t^4*399*[(BTR/S)-0.328]^3 = 0.0000 m^4.
-. Ia2 = t^4*[115*(w/t)/S + 5] = 0.0000 m^4.
-. Ia = MIN[ Ia1 , Ia2 ] = 0.0000 m^4.
-. n = 0.4054
-. k = 3.09
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/w)^2 = 846409.498 KPa.
-. Lambda = SQRT[ Fn / Fcr ] = 0.5415
-. In case of Lambda < 0.673
-. b = 0.046 m. (Fully effective).

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:14
http://www.MidasUser.com
Gen 2021 - 6 / 14 -
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

< For lip elements >

[ AISI-CFSD08 Specification I B4.2 Eq.B4.2-1~13 ]
-. HTR = d/t = 10.06 < 60 ---> O.K.
-. k = 0.43
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/d)^2 = 768511.798 KPa.
-. Lambda = SQRT[ Fn / Fcr ] = 0.5683
-. In case of Lambda < 0.673
-. ds = 0.018 m. (Fully effective).

( ). Calculate allowable compression force (Pao, L=0).

[ AISI-CFSD08 Specification I C4 Eq.C4-1~4 ]
-. bWeb = 0.083 m.
-. bFlange = 0.046 m.
-. bLip = 0.018 m.
-. Ae = A - [(a-bWeb) + 2*(b-bFlange) + 2*(c-bLip)]*t = 3.921e-04 m^2.
-. Pn = Ae * Fn = 97.32 kN.
-. Pao = Pn / Omega_c = 54.07 kN.

( ). Check ratio of axial load (Pu/Pao, L=0).

Pu 0.29
-. ----- = --------------- = 0.005 < 1.000 ---> O.K.
Pao 54.07

======================================================================================
[[[*]]] CHECK NOMINAL MOMENT STRENGTH ABOUT MAJOR AXIS (Mny1).
======================================================================================

( ). Calculate compression flange.

[ AISI-CFSD08 Specification I B4 Eq.B4-1~3, Eq.B4.1-1~11, Eq.B4.2-1~13 ]
-. BTR = w/t = 25.67 < 60 ---> O.K.
-. S = 1.28 * SQRT(Es / Fy) = 36.3294
-. In case of S/3 < BTR < S, n = 1/2
-. Ia1 = t^4*399*[(BTR/S)-0.328]^3 = 0.0000 m^4.
-. Ia2 = t^4*[115*(w/t)/S + 5] = 0.0000 m^4.
-. Ia = MIN[ Ia1 , Ia2 ] = 0.0000 m^4.
-. Is = c^3*t*sin^2(rad) / 12 = 0.0000 m^4.
-. D/w = 0.4329
-. In case of 0.25 < D/w < 0.8
-. k = MIN[ {4.82-5*(D/w)}*(Is/Ia)^n+0.43, 4.0 ] = 3.09
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/w)^2 = 846409.498 KPa.
-. Lambda = SQRT[ Fy / Fcr ] = 0.5415
-. In case of Lambda < 0.673
-. be = 0.046 m. (Fully effective).

( ). Calculate compression lip.

[ AISI-CFSD08 Specification I B4 Eq.B4-1~3, Eq.B4.1-1~11, Eq.B4.2-1~13 ]
-. HTR = d/t = 10.06 < 60 ---> O.K.
-. f1 = Fy*[{H/2 - t/2 - r*(1-cos(rad))/(H/2)}] = 241923.319 KPa.
-. f2 = Fy*[{H/2 - t/2 - r*(1-cos(rad))-c*sin(rad)/(H/2)}] = 182021.649 KPa.
-. Psi = f2 / f1 = 0.752
-. k = 0.578 / (Psi + 0.34) = 0.53
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/d)^2 = 945650.428 KPa.
-. Lambda = SQRT[ Fy / Fcr ] = 0.5058
-. In case of Lambda < 0.673
-. ds = 0.018 m. (Fully effective).
-. z_cg = 0.075 m.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:14
http://www.MidasUser.com
Gen 2021 - 7 / 14 -
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Calculate effective section properties about y-axis. Unit : m.

----------------------------------------------------------------------------------
Element Effective Len. z L*z L*z^2 I'1
----------------------------------------------------------------------------------
Comp. Flange 0.046 9.000e-04 4.158e-05 0.0000 ---
Comp. Lip 0.018 0.011 1.982e-04 2.1702e-06 4.9415e-07
Comp. Corner(Flange) 0.002 0.001 1.983e-06 0.0000 0.0000
Comp. Corner(Lip) 0.002 0.001 1.985e-06 0.0000 0.0000
Web 0.146 0.075 0.011 0.0008 0.0003
Tens. Flange 0.046 0.149 0.007 0.0010 ---
Tens. Lip 0.018 0.139 0.003 0.0003 4.9415e-07
Tens. Corner(Flange) 0.002 0.149 2.335e-04 3.4733e-05 0.0000
Tens. Corner(Lip) 0.002 0.149 2.336e-04 3.4750e-05 0.0000
----------------------------------------------------------------------------------
Sum 0.281 --- 0.021 0.0023 0.0003
----------------------------------------------------------------------------------

( ). Check if the web is fully effective.

[ AISI-CFSD08 Specification I B1.2(a), B2.3 Eq.B2.3-1~7 ]
-. HTR = w/t = 81.22 < 200 ---> O.K.
-. f1 = Fy * [ {z_cg-(r+t/2)} / (z_cg) ] = 241923.319 KPa.
-. f2 = -Fy * [ {(H-z_cg)-(r+t/2)} / (z_cg) ] = -241923.319 KPa.
-. Psi = f2 / f1 = -1.000
-. k = 4 + 2*(1-Psi)^3 + 2*(1-Psi) = 24.000
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/w)^2 = 657439.403 KPa.
-. Lambda = SQRT[ f1 / Fcr ] = 0.6066
-. basis = z_cg - (r+t/2) = 0.073 m.
-. be1 = be / (3 - Psi) = 0.037 m.
-. In case of ho / bo < 4
-. be2 = MIN[ be/2, be-be1 ] = 0.073 m.
-. In case of be1 + be2 > basis.
-. be( = be1 + be2) shall be taken as basis.
-. In case of Lambda < 0.673
-. be = 0.073 m. (Fully effective).

( ). Calculate moment on the basis of initiation of yielding about major axis(Mny1).

[ AISI-CFSD08 Specification I C3.1.1 Eq.C3.1.1-1 ]
-. I'y = L*z2 + I'1 - L*z_cg^2 = 0.0010 m^3.
-. Iy = I'y * t = 1.7125e-06 m^4.
-. Sey = Iy / (z_cg) = 2.2834e-05 m^3.
-. Mny1 = Sey * Fy = 5.67 kN-m.

======================================================================================
[[[*]]] CHECK NOMINAL LATERAL BUCKLING STRENGTH ABOUT MAJOR AXIS (Mny2).
======================================================================================

( ). Calculate bending coefficient (Cb).

-. Cb = 1.000 (User defined or default value)

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:14
http://www.MidasUser.com
Gen 2021 - 8 / 14 -
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Calculate moment on the basis of lateral buckling stress about major axis(fcy).
[ AISI-CFSD08 Specification I C3.1.2 Eq.C3.1.2-1~6 ]
-. Sfy = Iyy / Zbar = 2.2839e-05 m^3.
-. My = Sfy * Fy = 5.67 kN-m.
-. Mey = Cb * r0 * A * SQRT[ sigma_ez*sigma_t ] = 3.11 kN-m.
-. Mcy = Mey = 3.11 kN-m.
-. fcy = Mcy / Sfy = 136349.498 KPa.

( ). Calculate compression flange.

[ AISI-CFSD08 Specification I B4 Eq.B4-1~3, Eq.B4.1-1~11, Eq.B4.2-1~13 ]
-. BTR = w/t = 25.67 < 60 ---> O.K.
-. S = 1.28 * SQRT(Es / fcy) = 49.0164
-. In case of S/3 < BTR < S, n = 1/2
-. Ia1 = t^4*399*[(BTR/S)-0.328]^3 = 0.0000 m^4.
-. Ia2 = t^4*[115*(w/t)/S + 5] = 0.0000 m^4.
-. Ia = MIN[ Ia1 , Ia2 ] = 0.0000 m^4.
-. Is = c^3*t*sin^2(rad) / 12 = 0.0000 m^4.
-. D/w = 0.4329
-. In case of 0.25 < D/w < 0.8
-. k = MIN[ {4.82-5*(D/w)}*(Is/Ia)^n+0.43, 4.0 ] = 3.09
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/w)^2 = 846409.498 KPa.
-. Lambda = SQRT[ fcy / Fcr ] = 0.4014
-. In case of Lambda < 0.673
-. be = 0.046 m. (Fully effective).

( ). Calculate compression lip.

[ AISI-CFSD08 Specification I B4 Eq.B4-1~3, Eq.B4.1-1~11, Eq.B4.2-1~13 ]
-. HTR = d/t = 10.06 < 60 ---> O.K.
-. f1 = fcy*[{H/2 - t/2 - r*(1-cos(rad))/(H/2)}] = 132895.311 KPa.
-. f2 = fcy*[{H/2 - t/2 - r*(1-cos(rad))-c*sin(rad)/(H/2)}] = 99989.632 KPa.
-. Psi = f2 / f1 = 0.752
-. k = 0.578 / (Psi + 0.34) = 0.53
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/d)^2 = 945650.428 KPa.
-. Lambda = SQRT[ fcy / Fcr ] = 0.3749
-. In case of Lambda < 0.673
-. ds = 0.018 m. (Fully effective).
-. z_cg = 0.075 m.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:14
http://www.MidasUser.com
Gen 2021 - 9 / 14 -
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Calculate effective section properties about y-axis. Unit : m.

( ). Check if the web is fully effective.

[ AISI-CFSD08 Specification I B1.2(a), B2.3 Eq.B2.3-1~7 ]
-. HTR = w/t = 81.22 < 200 ---> O.K.
-. f1 = fcy * [ {z_cg-(r+t/2)} / (z_cg) ] = 132895.311 KPa.
-. f2 = -fcy * [ {(H-z_cg)-(r+t/2)} / (z_cg) ] = -132895.311 KPa.
-. Psi = f2 / f1 = -1.000
-. k = 4 + 2*(1-Psi)^3 + 2*(1-Psi) = 24.000
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/w)^2 = 657439.403 KPa.
-. Lambda = SQRT[ f1 / Fcr ] = 0.4496
-. basis = z_cg - (r+t/2) = 0.073 m.
-. be1 = be / (3 - Psi) = 0.037 m.
-. In case of ho / bo < 4
-. be2 = MIN[ be/2, be-be1 ] = 0.073 m.
-. In case of be1 + be2 > basis.
-. be( = be1 + be2) shall be taken as basis.
-. In case of Lambda < 0.673
-. be = 0.073 m. (Fully effective).

( ). Calculate moment on the basis of lateral buckling strength about major axis(Mny2).
[ AISI-CFSD08 Specification I C3.1.2 Eq.C3.1.2-1 ]
-. I'y = L*z2 + I'1 - L*z_cg^2 = 0.0010 m^3.
-. Iy = I'y * t = 1.7125e-06 m^4.
-. Scy = Iy / z_cg = 2.2834e-05 m^3.
-. Mny2 = (Mcy *Scy) / Sfy = 3.11 kN-m.

======================================================================================
[[[*]]] CHECK ALLOWABLE MOMENT STRENGTH ABOUT MAJOR AXIS (May).
======================================================================================

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:14
http://www.MidasUser.com
Gen 2021 - 10 / 14 -
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Check ratio of bending strength about major axis (Muy/May).

[ AISI-CFSD08 Specification I C3.1 Eq.C3.1-1 ]
-. Omega_f = 1.800
-. Mny1 = 5.67 kN-m.
-. Mny2 = 3.11 kN-m.
-. May = MIN[ Mny1, Mny2 ] / Omega_f = 1.73 kN-m.
Muy 0.51
-. ----- = --------------- = 0.294 < 1.000 ---> O.K.
May 1.73

======================================================================================
[[[*]]] CHECK ALLOWABLE MOMENT STRENGTH ABOUT MAJOR AXIS (Mayo, Ly=0).
======================================================================================

( ). Check ratio of bending strength about major axis (My/Mayo, L=0).

[ AISI-CFSD08 Specification I C3.1 Eq.C3.1-1 ]
-. Mnyo = Mny1
-. Mayo = Mnyo / Omega_f = 3.15 kN-m.
My 0.51
-. ------ = --------------- = 0.161 < 1.000 ---> O.K.
Mayo 3.15

======================================================================================
[[[*]]] CHECK NOMINAL MOMENT STRENGTH ABOUT MINOR AXIS (Mnz1).
======================================================================================

( ). Calculate compression web.

[ AISI-CFSD08 Specification I B2.1 Eq.B2.1-1~4 ]
-. HTR = w/t = 81.22 < 500 ---> O.K.
-. k = 4.00
-. y_cg = 0.018 m.
-. fcom = Fy * [ y_cg / (B - y_cg) ] = 141895.291 KPa.
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/w)^2 = 109573.234 KPa.
-. Lambda = SQRT[ fcom / Fcr ] = 1.1381
-. In case of Lambda > 0.673
-. Rho = (1 - 0.22/Lambda)/Lambda = 0.7088
-. b = Rho*w = 0.104 m. (Partially effective).

( ). Calculate effective section properties about z-axis. Unit : m.

-------------------------------------------------------------------------------
Element Effective Len. y L*y L*y^2 I'1
-------------------------------------------------------------------------------
Flanges 0.092 0.025 0.002 5.7750e-05 1.6435e-05
Left Corners 0.003 0.001 3.968e-06 0.0000 0.0000
Right Corners 0.003 0.049 1.531e-04 7.4622e-06 0.0000
Web 0.104 9.000e-04 9.327e-05 0.0000 ---
Lips 0.036 0.049 0.002 8.7271e-05 ---
-------------------------------------------------------------------------------
Sum 0.239 --- 0.004 0.0002 1.6436e-05
-------------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:14
http://www.MidasUser.com
Gen 2021 - 11 / 14 -
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Check if the flange is fully effective.

[ AISI-CFSD08 Specification I B1.2(a), B2.3 Eq.B2.3-1~4 ]
-. HTR = w/t = 25.67 < 200 ---> O.K.
-. f1 = Fy * [{y_cg-(r+t/2)} / (B-y_cg)] = 127071.239 KPa.
-. f2 = -Fy * [{(B-y_cg)-(r+t/2)} / (B-y_cg)] = -233387.288 KPa.
-. Psi = f2 / f1 = -1.837
-. k = 4 + 2*(1-Psi)^3 + 2*(1-Psi) = 55.325
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/w)^2 =15176603.688 KPa.
-. Lambda = SQRT[ f1 / Fcr ] = 0.0915
-. basis = y_cg - (r+t/2) = 0.016 m.
-. be1 = be / (3 - Psi) = 0.010 m.
-. be2 = MIN[ be/2, be-be1 ] = 0.023 m.
-. In case of be1 + be2 > basis.
-. be( = be1 + be2) shall be taken as basis.
-. In case of Lambda < 0.673
-. be = 0.016 m. (Fully effective).

( ). Calculate moment on the basis of initiation of yielding about minor axis(Mnz1).

[ AISI-CFSD08 Specification I C3.1.1 Eq.C3.1.1-1 ]
-. I'z = L*y2 + I'1 - L*y_cg^2 = 9.0118e-05 m^3.
-. Iz = I'z * t = 1.6221e-07 m^4.
-. Sez = Iz / (B - y_cg) = 5.0989e-06 m^3.
-. Mnz1 = Sez * Fy = 1.27 kN-m.

======================================================================================
[[[*]]] CHECK NOMINAL LATERAL BUCKLING STRENGTH ABOUT MINOR AXIS (Mnz2).
======================================================================================

( ). Calculate moment on the basis of lateral buckling stress about minor axis(fcz).
[ AISI-CFSD08 Specification I C3.1.2.1 Eq.C3.1.2.1-15 ]
-. Cs = 1.000 (Compression).
-. Sfz = Izz / Ybar = 1.1666e-05 m^3.
-. Mz = Sfz * Fy = 2.90 kN-m.
-. Mez = Cs * A * sigma_ey
*{j+Cs*SQRT[j^2+r0^2*(sigma_t/sigma_ey)]}/Ctfz = 60.09 kN-m.
-. Mcz = Mz = 2.90 kN-m.
-. fcz = Mcz / Sfz = 248211.340 KPa.

( ). Calculate compression web.

[ AISI-CFSD08 Specification I B2.1 Eq.B2.1-1~4 ]
-. HTR = w/t = 81.22 < 500 ---> O.K.
-. k = 4.00
-. y_cg = 0.020 m.
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/w)^2 = 109573.234 KPa.
-. Lambda = SQRT[ fcom / Fcr ] = 1.5051
-. In case of Lambda > 0.673
-. Rho = (1 - 0.22/Lambda)/Lambda = 0.5673
-. b = Rho*w = 0.083 m. (Partially effective).

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:14
http://www.MidasUser.com
Gen 2021 - 12 / 14 -
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

( ). Calculate effective section properties about z-axis. Unit : m.

-------------------------------------------------------------------------------
Element Effective Len. y L*y L*y^2 I'1
-------------------------------------------------------------------------------
Flanges 0.092 0.025 0.002 5.7750e-05 1.6435e-05
Left Corners 0.003 0.001 3.968e-06 0.0000 0.0000
Right Corners 0.003 0.049 1.531e-04 7.4622e-06 0.0000
Web 0.083 9.000e-04 7.465e-05 0.0000 ---
Lips 0.036 0.049 0.002 8.7271e-05 ---
-------------------------------------------------------------------------------
Sum 0.218 --- 0.004 0.0002 1.6436e-05
-------------------------------------------------------------------------------

( ). Check if the flange is fully effective.

[ AISI-CFSD08 Specification I B1.2(a), B2.3 Eq.B2.3-1~4 ]
-. HTR = w/t = 25.67 < 200 ---> O.K.
-. f1 = fcz * [{y_cg-(r+t/2)} / (B-y_cg)] = 147495.444 KPa.
-. f2 = -fcz * [{(B-y_cg)-(r+t/2)} / (B-y_cg)] = -232580.511 KPa.
-. Psi = f2 / f1 = -1.577
-. k = 4 + 2*(1-Psi)^3 + 2*(1-Psi) = 43.376
-. Fcr = k*Pi^2*E/(12*(1-por^2))*(t/w)^2 =11898770.098 KPa.
-. Lambda = SQRT[ f1 / Fcr ] = 0.1113
-. basis = y_cg - (r+t/2) = 0.018 m.
-. be1 = be / (3 - Psi) = 0.010 m.
-. be2 = MIN[ be/2, be-be1 ] = 0.023 m.
-. In case of be1 + be2 > basis.
-. be( = be1 + be2) shall be taken as basis.
-. In case of Lambda < 0.673
-. be = 0.018 m. (Fully effective).

( ). Calculate moment on the basis of lateral buckling strength about minor axis(Mnz2).
[ AISI-CFSD08 Specification I C3.1.2 Eq.C3.1.2-1 ]
-. I'z = L*y2 + I'1 - L*y_cg^2 = 8.3348e-05 m^3.
-. Iz = I'z * t = 1.5003e-07 m^4.
-. Scz = Iz / y_cg = 7.5661e-06 m^3.
-. Mnz2 = (Mcz * Scz) / Sfz = 1.88 kN-m.

======================================================================================
[[[*]]] CHECK ALLOWABLE MOMENT STRENGTH ABOUT MINOR AXIS (Maz).
======================================================================================

( ). Check ratio of bending strength about minor axis (Muz/Maz).

[ AISI-CFSD08 Specification I C3.1 Eq.C3.1-1 ]
-. Omega_f = 1.800
-. Mnz1 = 1.27 kN-m.
-. Mnz2 = 1.88 kN-m.
-. Maz = MIN[ Mnz1, Mnz2 ] / Omega_f = 0.70 kN-m.
Muz 2.98e-03
-. ----- = --------------- = 0.004 < 1.000 ---> O.K.
Maz 0.70

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:14
http://www.MidasUser.com
Gen 2021 - 13 / 14 -
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name ROOF.acs

======================================================================================
[[[*]]] CHECK ALLOWABLE MOMENT STRENGTH ABOUT MINOR AXIS (Mazo, Lz=0).
======================================================================================

( ). Check ratio of bending strength about minor axis (Mz/Mazo, L=0).

[ AISI-CFSD08 Specification I C3.1 Eq.C3.1-1 ]
-. Mnzo = Mnz1
-. Mazo = Mnzo / Omega_f = 0.70 kN-m.
Mz 2.94e-03
-. ------ = --------------- = 0.004 < 1.000 ---> O.K.
Mazo 0.70

( ). Calculate shear strength in local-z direction (Vaz).

[ AISI-CFSD08 Specification I C3.2.1 Eq.C3.2.1-1~7 ]
-. HTR = h/t = 81.222
-. kv = 5.340 (Default value)
-. HTRa = 1.51*SQRT[ Es*kv/Fy ] = 99.037
-. Omega_v = 1.600
-. Vaz1 = 0.60*t^2*SQRT[ kv*Fy*Es ] / Omega_v = 19.78 kN.
-. Vaz2 = 0.6 * Fy * h * t / Omega_v = 24.49 kN.
-. Vaz = MIN[ Vaz1, Vaz2 ] = 19.78 kN.

( ). Check ratio of shear strength (Vuz/Vaz).

( LCB = 2, POS = 1/2 )
-. Applied shear force : Vuz = 0.10 kN.
-. Applied bending moment : My = 0.51 kN-m.
Vuz 0.10
-. ----- = --------------- = 0.005 < 1.000 ---> O.K.
Vaz 19.78
[ My ]^2 [ Vuz ]^2
-. [ ---- ] + [ ----- ] = 0.161 < 1.000 ---> O.K.
[ Mayo ] [ Vaz ]

======================================================================================
[[[*]]] CHECK INTERACTION OF COMBINED AXIAL LOAD AND BENDING.
======================================================================================

( ). Check interaction ratio of combined strength.

[ AISI-CFSD08 Specification I C5 Eq.C5-1~3 ]
-. In case of Pu/Pa < 0.15 ---> Eq.C5-3
-. ComRat = Pu/Pa + My/May + Mz/Maz
= 0.016 + 0.293 + 0.004 = 0.313 < 1.000 ---> O.K.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 21:14
http://www.MidasUser.com
Gen 2021 - 14 / 14 -
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:12
http://www.MidasUser.com
Gen 2021 -1/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

25 1 DL( 0.900) + RS-M(RS)(-1.000)

26 1 DL( 0.900) + RS-O(RS)(-1.000)
--------------------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:12
http://www.MidasUser.com
Gen 2021 -2/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

*. PROJECT :
*. MEMBER NO = 2940, ELEMENT TYPE = Beam
*. LOADCOMB NO = 2, MATERIAL NO = 1, SECTION NO = 40
*. UNIT SYSTEM : kN, m

*. SECTION PROPERTIES : Designation = CANOPY-2''x2''x2mm

Shape = B - Section. (Built-up)
Depth = 0.050, Flg Width = 0.050, Web Center = 0.048
Web Thick = 0.002, Top F Thick = 0.002, Bot.F Thick = 0.002

Area = 3.84000e-04, Asy = 2.00000e-04, Asz = 2.00000e-04

Ybar = 2.50000e-02, Zbar = 2.50000e-02, Qyb = 8.64500e-04, Qzb = 8.64500e-04
Syy = 5.90848e-06, Szz = 5.90848e-06, Zyy = 6.91600e-06, Zzz = 6.91600e-06
Iyy = 1.47712e-07, Izz = 1.47712e-07, Iyz = 0.00000e+00
ry = 1.96129e-02, rz = 1.96129e-02
J = 2.21184e-07, Cwp = 1.00000e+28

*. DESIGN PARAMETERS FOR STRENGTH EVALUATION :

Ly = 3.50000e+00, Lz = 3.50000e+00, Lu = 3.50000e+00
Ky = 1.00000e+00, Kz = 1.00000e+00

*. MATERIAL PROPERTIES :
Fy = 2.48211e+05, Es = 1.99948e+08, MATERIAL NAME = A36

( ). Compute moment magnification factors(B1y,B1z).

-. If tension or bending member.
-. Assumed B1y = 1.00
-. Assumed B1z = 1.00

( ). Magnification factors for sidesway moments(B2y,B2z).

-. B2y = 1.00 (Default value)
-. B2z = 1.00 (Default value)

( ). Given factored axial forces and moments at <1/2>.

----------------------------------------------------------------
Load Case Pa My Mz
----------------------------------------------------------------
DL 0.00 0.44 0.00
LL 0.00 0.58 0.00
DL+LL 0.00 1.02 0.00
OTHER CASES 0.00 0.00 0.00
----------------------------------------------------------------
TOTAL 0.00 1.02 0.00
----------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:12
http://www.MidasUser.com
Gen 2021 -3/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

( ). Compute magnified moments.

-. Muy = B1y*My(DL+LL) + B2y*My(OTHERS) = 1.02 kN-m.
-. Muz = B1z*Mz(DL+LL) + B2z*Mz(OTHERS) = 0.00 kN-m.

( ). Check slenderness ratio of axial tension member (L/r).

[ AISC(15th) Specification D1. ]
-. L/r = 178.5 < 300.0 ---> O.K.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 1.12*SQRT[Es/Fy] = 31.79
-. Lambda_r = 1.49*SQRT[Es/Fy] = 42.29

( ). Calculate limiting width-thickness ratio of web for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 2.42*SQRT[Es/Fy] = 68.69
-. Lambda_r = 5.70*SQRT[Es/Fy] = 161.78

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 23.00 < Lambda_p = 31.79 ---> COMPACT.

( ). Check width-thickness ratio of web (DTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. DTR = 23.00 < Lambda_p = 68.69 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F7.1. (F7-1) ]
-. Mn.Y = Mp = Fy*Zyy = 1.7166 kN-m.

--------------------------------------------------------------------------
[*] Check Flange Local Buckling (FLB).
--------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:12
http://www.MidasUser.com
Gen 2021 -4/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

( ). Calculate nominal flexural strength for Flange local buckling (FLB).

[ AISC(15th) Specification F7.2. ]
-. For compact sections, flange local buckling is not applied.

--------------------------------------------------------------------------
[*] Check Web Local Buckling (WLB).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Web local buckling (WLB).

[ AISC(15th) Specification F7.3. (a) ]
-. For compact sections, web local buckling is not applied.

--------------------------------------------------------------------------
[*] Check Lateral-Torsional Buckling (LTB).
--------------------------------------------------------------------------

( ). Compute limiting laterally unbraced length for the limit state of yielding (Lp).
[ AISC(15th) Specification F7.4 (F7-12) ]
-. Lp = 0.13*Es*rz*SQRT[J*Ag]/Mp = 2.74 m.

( ). Compute limiting laterally unbraced length for the limit state of

inelastic lateral torsional buckling (Lr).
[ AISC(15th) Specification F7.4 (F7-13) ]
-. Lp = 2*Es*rz*SQRT[J*Ag]/(0.7*Fy*Syy) = 70.41 m.

( ). Calculate nominal flexural strength for Lateral-torsional buckling (LTB).

[ AISC(15th) Specification F7.4 (b) (F7-11) ]
-. Lp < Lb < Lr.
[ Lb-Lp ]
-. Mn = Cb *[ Mp - (Mp-0.7*Fy*Syy) * ------- ] = 1.71 kN-m.
[ Lr-Lp ]
-. Mn.LTB = MIN [ Mn, Mp ] = 1.71 kN-m.

( ). Compute flexural strength about major axis (phiMny).

-. Mny = MIN[ Mn.Y, Mn.LTB ] = 1.71 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMny = phi*Mny = 1.54 kN-m.

( ). Check ratio of flexural strength (Muy/phiMny).

Muy 1.02
-. -------- = --------------- = 0.665 < 1.000 ---> O.K.
phiMny 1.54

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:12
http://www.MidasUser.com
Gen 2021 -5/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 1.12*SQRT[Es/Fy] = 31.79
-. Lambda_r = 1.49*SQRT[Es/Fy] = 42.29

( ). Calculate limiting width-thickness ratio of web for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 2.42*SQRT[Es/Fy] = 68.69
-. Lambda_r = 5.70*SQRT[Es/Fy] = 161.78

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 23.00 < Lambda_p = 31.79 ---> COMPACT.

( ). Check width-thickness ratio of web (DTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. DTR = 23.00 < Lambda_p = 68.69 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F7.1. (F7-1) ]
-. Mn.Y = Mp = Fy*Zzz = 1.7166 kN-m.

--------------------------------------------------------------------------
[*] Check Flange Local Buckling (FLB).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Flange local buckling (FLB).

[ AISC(15th) Specification F7.2. ]
-. For compact sections, flange local buckling is not applied.

--------------------------------------------------------------------------
[*] Check Web Local Buckling (WLB).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Web local buckling (WLB).

[ AISC(15th) Specification F7.3. (a) ]
-. For compact sections, web local buckling is not applied.

( ). Compute flexural strength about minor axis (phiMnz).

-. Mnz = Mn.Y = 1.72 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMnz = phi*Mnz = 1.54 kN-m.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:12
http://www.MidasUser.com
Gen 2021 -6/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

( ). Check ratio of flexural strength (Muz/phiMnz).

Muz 0.00
-. -------- = --------------- = 0.000 < 1.000 ---> O.K.
phiMnz 1.54

======================================================================================
[[[*]]] CHECK TORSIONAL STRENGTH FOR COMBINED ACTION.
======================================================================================

( ). Calculate critical stress (Fcr).

[ AISC(15th) Specification H3.1. (H3-3) ]
-. HTR = h/tw = 23.000
-. HTR < 2.45*SQRT[Es/Fy]
-. Fcr = 0.6*Fy = 148926.8039 KPa.

( ). Calculate torsional strength (phiTn).

[ AISC(15th) Specification H3.1. ]
-. C = 2*(B-t)*(H-t)*t - 4.5*(4-pi)*t^3 = 9.185e-06 m^3.
-. Resistance factor for torsion : phi = 0.900
-. phiTn = phi*Fcr*C = 1.23 kN-m.

( ). Check ratio of torsional strength (Tu/phiTn).

( LCB = 2, POS = 1/2 )
Tu 0.25
-. ------- = --------------- = 0.205 < 1.000 ---> O.K.
phiTn 1.23
---> Tr/Tc > 0.2 : The torsional effects shall be considered.

======================================================================================
[[[*]]] CHECK SHEAR STRENGTH FOR COMBINED ACTION.
======================================================================================

( ). Calculate the web shear buckling coefficient (Cv2).

[ AISC(15th) Specification G2.2 (G2-9) ]
-. for webs of all other doubly/singly symmetric shapes and channels.
-. kv (web plate buckling coefficient) = 5.00
-. h/tw = 23.000< 1.10*SQRT[kv*Es/Fy] = 69.811
-. Cv2 = 1.00

( ). Calculate shear strength in local-z direction (phiVnz).

[ AISC(15th) Specification G4. ]
-. Aw = 2.0*h*t = 0.0002 m^2.
-. Vn = 0.6*Fy*Aw*Cv2 = 27.4025 kN.
-. Resistance factor for shear : phi = 0.90
-. phiVnz = phi*Vn = 24.66 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 2, POS = 1/2 )
-. Applied shear force : Vuz = 0.07 kN.
Vuz 0.07
-. -------- = --------------- = 0.003 < 1.000 ---> O.K.
phiVnz 24.66

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:12
http://www.MidasUser.com
Gen 2021 -7/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

( ). Check interaction ratio of combined strength.

[ AISC(15th) Specification H3.2 (H3-6) ]
-. Tr/Tc > 0.20,
[ Pr Mry ] [ Vrz Tr ]^2
-. ComRaty = [---- + -----] + [----- + ----]
[ Pc Mcy ] [ Vcz Tc ]
= 0.000 + 0.665 + ( 0.003 + 0.205)^2
= 0.709
[ Pr Mrz ] [ Vry Tr ]^2
-. ComRatz = [---- + -----] + [----- + ----]
[ Pc Mcz ] [ Vcy Tc ]
= 0.000 + 0.000 + ( 0.000 + 0.205)^2
= 0.042
-. ComRat = MAX[ComRaty, ComRatz] = 0.709

======================================================================================
[[[*]]] CHECK TORSIONAL STRENGTH.
======================================================================================

( ). Calculate critical stress (Fcr).

[ AISC(15th) Specification H3.1. (H3-3) ]
-. HTR = h/tw = 23.000
-. HTR < 2.45*SQRT[Es/Fy]
-. Fcr = 0.6*Fy = 148926.8039 KPa.

( ). Calculate torsional strength (phiTn).

[ AISC(15th) Specification H3.1. ]
-. C = 2*(B-t)*(H-t)*t - 4.5*(4-pi)*t^3 = 9.185e-06 m^3.
-. Resistance factor for torsion : phi = 0.900
-. phiTn = phi*Fcr*C = 1.23 kN-m.

( ). Check ratio of torsional strength (Tu/phiTn).

( LCB = 2, POS = J )
Tu 0.25
-. ------- = --------------- = 0.205 < 1.000 ---> O.K.
phiTn 1.23

( ). Calculate the web shear buckling coefficient (Cv2).

[ AISC(15th) Specification G2.2 (G2-9) ]

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:12
http://www.MidasUser.com
Gen 2021 -8/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

-. for webs of all other doubly/singly symmetric shapes and channels.

-. kv (web plate buckling coefficient) = 5.00
-. h/tw = 23.000< 1.10*SQRT[kv*Es/Fy] = 69.811
-. Cv2 = 1.00

( ). Calculate shear strength in local-z direction (phiVnz).

[ AISC(15th) Specification G4. ]
-. Aw = 2.0*h*t = 0.0002 m^2.
-. Vn = 0.6*Fy*Aw*Cv2 = 27.4025 kN.
-. Resistance factor for shear : phi = 0.90
-. phiVnz = phi*Vn = 24.66 kN.

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 2, POS = J )
-. Applied shear force : Vuz = 1.63 kN.
Vuz 1.63
-. -------- = --------------- = 0.066 < 1.000 ---> O.K.
phiVnz 24.66

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 20:12
http://www.MidasUser.com
Gen 2021 -9/9-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 11:56
http://www.MidasUser.com
Gen 2021 -1/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

25 1 DL( 0.900) + RS-M(RS)(-1.000)

26 1 DL( 0.900) + RS-O(RS)(-1.000)
--------------------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 11:56
http://www.MidasUser.com
Gen 2021 -2/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

*. PROJECT :
*. MEMBER NO = 1857, ELEMENT TYPE = Beam
*. LOADCOMB NO = 2, MATERIAL NO = 1, SECTION NO = 41
*. UNIT SYSTEM : kN, m

*. SECTION PROPERTIES : Designation = CANOPY, I 36c

Shape = I - Section. (Rolled)
Depth = 0.360, Top F Width = 0.140, Bot.F Width = 0.140
Web Thick = 0.014, Top F Thick = 0.016, Bot.F Thick = 0.016

Area = 9.08400e-03, Asy = 2.94933e-03, Asz = 5.04000e-03

*. DESIGN PARAMETERS FOR STRENGTH EVALUATION :

Ly = 6.00000e-01, Lz = 6.00000e-01, Lu = 6.00000e-01
Ky = 1.00000e+00, Kz = 1.00000e+00

*. MATERIAL PROPERTIES :
Fy = 2.48211e+05, Es = 1.99948e+08, MATERIAL NAME = A36

( ). Compute moment magnification factors(B1y,B1z).

-. If tension or bending member.
-. Assumed B1y = 1.00
-. Assumed B1z = 1.00

( ). Magnification factors for sidesway moments(B2y,B2z).

-. B2y = 1.00 (Default value)
-. B2z = 1.00 (Default value)

( ). Given factored axial forces and moments at <I>.

----------------------------------------------------------------
Load Case Pa My Mz
----------------------------------------------------------------
DL 0.00 -112.71 0.00
LL 0.00 -121.70 0.00
DL+LL 0.00 -234.40 0.00
OTHER CASES 0.00 0.00 0.00
----------------------------------------------------------------
TOTAL 0.00 -234.40 0.00
----------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 11:56
http://www.MidasUser.com
Gen 2021 -3/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

( ). Compute magnified moments.

-. Muy = B1y*My(DL+LL) + B2y*My(OTHERS) = -234.40 kN-m.
-. Muz = B1z*Mz(DL+LL) + B2z*Mz(OTHERS) = 0.00 kN-m.

( ). Check slenderness ratio of axial tension member (L/r).

[ AISC(15th) Specification D1. ]
-. L/r = 23.1 < 300.0 ---> O.K.

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0010 m^3.
-. Syt = 0.0010 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Calculate limiting width-thickness ratio of web for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 3.76*SQRT[Es/Fy] = 106.72
-. Lambda_r = 5.70*SQRT[Es/Fy] = 161.78

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 4.43 < Lambda_p = 10.79 ---> COMPACT.

( ). Check width-thickness ratio of web (DTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. DTR = 21.74 < Lambda_p = 106.72 ---> COMPACT.

( ). Calculate lateral-torsional buckling modification factor (Cb).

[ AISC(15th) Specification F1.(2) (F1-1) ]
-. Cb = 1.000 (User defined or default value)

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 11:56
http://www.MidasUser.com
Gen 2021 -4/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F2.1 (F2-1) ]
-. Mn.Y = Mp = Fy*Zyy = 282.67 kN-m.

--------------------------------------------------------------------------
[*] Check Lateral-Torsional Buckling (LTB).
--------------------------------------------------------------------------

( ). Compute limiting laterally unbraced length for the limit state of yielding (Lp).
[ AISC(15th) Specification F2.2 (F2-5) ]
-. Lp = 1.76*rz*SQRT[Es/Fy] = 1.30 m.

( ). Calculate nominal flexural strength for Lateral-torsional buckling (LTB).

-. Lb < Lp ---> Lateral-torsional buckling is not applied.

( ). Compute flexural strength about major axis (phiMny).

-. Mny = Mn.Y = 282.67 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMny = phi*Mny = 254.40 kN-m.

( ). Check ratio of flexural strength (Muy/phiMny).

Muy 234.40
-. -------- = --------------- = 0.921 < 1.000 ---> O.K.
phiMny 254.40

( ). Elastic section modulus refered to tension and compression flanges.

-. Syc = 0.0010 m^3.
-. Syt = 0.0010 m^3.

( ). Calculate limiting width-thickness ratio of flange for flexure.

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. Lambda_p = 0.38*SQRT[Es/Fy] = 10.79
-. Lambda_r = 1.00*SQRT[Es/Fy] = 28.38

( ). Check width-thickness ratio of flange (BTR).

[ AISC(15th) Specification B4. <Table B4.1b> ]
-. BTR = 4.43 < Lambda_p = 10.79 ---> COMPACT.

--------------------------------------------------------------------------
[*] Check Yielding (Y).
--------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 11:56
http://www.MidasUser.com
Gen 2021 -5/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

( ). Calculate nominal flexural strength for Yielding (Y).

[ AISC(15th) Specification F6.1 (F6-1) ]
-. Mn.Y = Mp = MIN[ Fy*Zzz, 1.6*Fy*Szz ] = 34.83 kN-m.

--------------------------------------------------------------------------
[*] Check Flange Local Buckling (FLB).
--------------------------------------------------------------------------

( ). Calculate nominal flexural strength for Flange local buckling (FLB).

-. COMPACT flange ---> the limit state of flange local buckling is not applied.

( ). Compute flexural strength about minor axis (phiMnz).

-. Mnz = Mn.Y = 34.83 kN-m.
-. Resistance factor for flexure : phi = 0.90
-. phiMnz = phi*Mnz = 31.35 kN-m.

( ). Check ratio of flexural strength (Muz/phiMnz).

Muz 0.00
-. -------- = --------------- = 0.000 < 1.000 ---> O.K.
phiMnz 31.35

( ). Check interaction ratio of combined strength.

[ AISC(15th) Specification H1.1(b) ]
-. Pr/Pc < 0.20 ---> Formula(H1-1b)
Pr [ Mry Mrz ]
-. ComRat = ------ + [ ----- + ----- ]
2*Pc [ Mcy Mcz ]
= 0.000 + [ 0.921 + 0.000 ]
= 0.921 < 1.000 ---> O.K.

( ). Calculate shear strength coefficient (Cv1).

[ AISC(15th) Specification G2.1 (G2-2) ]
-. for Rolled H-Shape members.
-. h/tw = 21.743 < 2.24*SQRT[Es/Fy] = 63.576
-. Cv1 = 1.00

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 11:56
http://www.MidasUser.com
Gen 2021 -6/7-
midas Gen Steel Code Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-11-25.acs

( ). Calculate shear strength in local-z direction (phiVnz).

( ). Check ratio of shear strength (Vu/phiVn).

( LCB = 2, POS = I )
-. Applied shear force : Vuz = 64.10 kN.
Vuz 64.10
-. -------- = --------------- = 0.085 < 1.000 ---> O.K.
phiVnz 750.59

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/23/2025 11:56
http://www.MidasUser.com
Gen 2021 -7/7-
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB1

Section : END(I)
1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material
(1) F'c : 20,684KPa
(2) Fy : 227,600KPa
(3) Fys : 227,600KPa

3. Section
(1) Section Size : 0.250 x 0.500m (R-Section)
(2) Cover : 0.0400m
(3) Compression : Not Considered
(4) Splicing Limit : 50%

0.250
0.0400

0.500
0.0400

4. Moments and Forces

(1) Mu,top : 62.00kN·m
(2) Mu,bottom : 37.98kN·m
(3) Vu : 31.98kN

5. Reinforcement
(1) Top Bar : 4-#5 (As = 0.000800m²)
Layer 1 : 2 EA (Cc = 0.0575m)
Layer 2 : 2 EA (Cc = 0.0987m)
(2) Bot Bar : 4-#5 (As = 0.000800m²)
Layer 1 : 2 EA (Cc = 0.0575m)
Layer 2 : 2 EA (Cc = 0.0987m)
(3) Stirrup : 2-#[email protected] (As = 0.000142m²)

6. Check Bending Moment Capacity (Positive)

(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
2025-07-01 17:38 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB1

40000 40000
smax1 = 15 ( ) - 2.5cc smax2 = 12 ( )
fs fs
smax = min ( smax1 , smax2 ) = 0.554m, Nreq = 2
s = 0.135 < 0.554m → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 200
ρmin.11 = 3 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0061
4 Mu
ρmin.2 = = 0.0057
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0057
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0281
fy εc + 0.004
ρmax = ρet = 0.0281
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0076
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 0.0414m
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 73.05kN·m
øMn = 65.74kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.578 → O.K

7. Check Bending Moment Capacity (Negative)

(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
40000 40000
smax1 = 15 ( ) - 2.5cc smax2 = 12 ( )
fs fs
smax = min ( smax1 , smax2 ) = 0.554m, Nreq = 2
s = 0.135 < 0.554m → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 200
ρmin.11 = 3 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0061
4 Mu
ρmin.2 = = 0.0095
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0061
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0281
fy εc + 0.004
ρmax = ρet = 0.0281
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0076
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 0.0414m
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 73.05kN·m

2025-07-01 17:38 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB1

øMn = 65.74kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.943 → O.K

8. Check Shear Capacity

(1) Calculate shear strength by concrete
ø = 0.750 d = 0.422m
øVc = ø 2 f'c bw d = 59.75kN
1
øVc < Vu < øVc → Minimum shear reinforcement is required
2
(2) Calculate required shear strength by shear reinforcement
bw bw
Av.min1/s = 0.75 f'c Av.min2/s = 50
fyt fyt
Av.min = max [ Av.min1 , Av.min2 ] = 0.000379m²/m
Av,req = Av.min = 0.000379m²/m
(3) Calculate shear strength by stirrup
Nleg = 2 Av1 = 0.0000710m² (#3)
Av fyt d
øVs = ø = 102kN
s
(4) Calculate ratio of shear capacity
øVn = øVc + øVs = 162kN
Vu / øVn = 0.197 → O.K
(5) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 24in ] = 0.211m
Nleg Av1
sreq = = 0.375m
Av.req
smax = min [ smax.0 sreq ] = 0.211m
s = 0.100m < smax = 0.211m → O.K

Section : MIDDLE
1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material
(1) F'c : 20,684KPa
(2) Fy : 227,600KPa
(3) Fys : 227,600KPa

3. Section
(1) Section Size : 0.250 x 0.500m (R-Section)
(2) Cover : 0.0400m
(3) Compression : Not Considered
(4) Splicing Limit : 50%

2025-07-01 17:38 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB1

0.250
0.0400

0.500
0.0400

4. Moments and Forces

(1) Mu,top : 28.79kN·m
(2) Mu,bottom : 35.35kN·m
(3) Vu : 26.68kN

6. Check Bending Moment Capacity (Positive)

2025-07-01 17:38 4
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB1

As
ρ= = 0.0076
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 0.0414m
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 73.05kN·m
øMn = 65.74kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.538 → O.K

7. Check Bending Moment Capacity (Negative)

(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
40000 40000
smax1 = 15 ( ) - 2.5cc smax2 = 12 ( )
fs fs
smax = min ( smax1 , smax2 ) = 0.554m, Nreq = 2
s = 0.135 < 0.554m → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 200
ρmin.11 = 3 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0061
4 Mu
ρmin.2 = = 0.0043
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0043
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0281
fy εc + 0.004
ρmax = ρet = 0.0281
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0076
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 0.0414m
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 73.05kN·m
øMn = 65.74kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.438 → O.K

8. Check Shear Capacity

2025-07-01 17:38 5
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB1

øVn = øVc + øVs = 111kN

Vu / øVn = 0.241 → O.K
(4) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 24in ] = 0.211m
Nleg Av1
sreq = = 0.211m
Av.req
smax = min [ smax.0 sreq ] = 0.211m
s = 0.200m < smax = 0.211m → O.K

Section : END(J)
1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material
(1) F'c : 20,684KPa
(2) Fy : 227,600KPa
(3) Fys : 227,600KPa

3. Section
(1) Section Size : 0.250 x 0.500m (R-Section)
(2) Cover : 0.0400m
(3) Compression : Not Considered
(4) Splicing Limit : 50%

0.250
0.0400

0.500
0.0400

4. Moments and Forces

(1) Mu,top : 58.99kN·m
(2) Mu,bottom : 55.49kN·m

2025-07-01 17:38 6
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB1

(3) Vu : 25.61kN

6. Check Bending Moment Capacity (Positive)

(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
40000 40000
smax1 = 15 ( ) - 2.5cc smax2 = 12 ( )
fs fs
smax = min ( smax1 , smax2 ) = 0.554m, Nreq = 2
s = 0.135 < 0.554m → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 200
ρmin.11 = 3 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0061
4 Mu
ρmin.2 = = 0.0085
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0061
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0281
fy εc + 0.004
ρmax = ρet = 0.0281
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0076
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 0.0414m
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 73.05kN·m
øMn = 65.74kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.844 → O.K

7. Check Bending Moment Capacity (Negative)

2025-07-01 17:38 7
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB1

4 Mu
ρmin.2 = = 0.0090
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0061
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0281
fy εc + 0.004
ρmax = ρet = 0.0281
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0076
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 0.0414m
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 73.05kN·m
øMn = 65.74kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.897 → O.K

8. Check Shear Capacity

(1) Calculate shear strength by concrete
ø = 0.750 d = 0.422m
øVc = ø 2 f'c bw d = 59.75kN
1
Vu < øVc → Shear reinforcement is not required
2
(2) Calculate shear strength by stirrup
Nleg = 2 Av1 = 0.0000710m² (#3)
Av fyt d
øVs = ø = 102kN
s
(3) Calculate ratio of shear capacity
øVn = øVc + øVs = 162kN
Vu / øVn = 0.158 → O.K
(4) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 24in ] = 0.211m
Nleg Av1
sreq = = 0.211m
Av.req
smax = min [ smax.0 sreq ] = 0.211m
s = 0.100m < smax = 0.211m → O.K

2025-07-01 17:38 8
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB2

Section : END(I)
1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material
(1) F'c : 20,684KPa
(2) Fy : 227,600KPa
(3) Fys : 227,600KPa

3. Section
(1) Section Size : 0.300 x 0.600m (R-Section)
(2) Cover : 0.0400m
(3) Compression : Not Considered
(4) Splicing Limit : 50%

0.300
0.0400

0.600
0.0400

4. Moments and Forces

(1) Mu,top : 96.43kN·m
(2) Mu,bottom : 28.35kN·m
(3) Vu : 35.14kN

5. Reinforcement
(1) Top Bar : 5-#5 (As = 0.001000m²)
Layer 1 : 3 EA (Cc = 0.0575m)
Layer 2 : 2 EA (Cc = 0.0987m)
(2) Bot Bar : 4-#5 (As = 0.000800m²)
Layer 1 : 4 EA (Cc = 0.0575m)
(3) Stirrup : 2-#[email protected] (As = 0.000142m²)

6. Check Bending Moment Capacity (Positive)

(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar

2025-07-04 21:03 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB2

40000 40000
smax1 = 15 ( ) - 2.5cc smax2 = 12 ( )
fs fs
smax = min ( smax1 , smax2 ) = 0.554m, Nreq = 2
s = 0.0617 < 0.554m → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 200
ρmin.11 = 3 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0061
4 Mu
ρmin.2 = = 0.0021
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0021
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0281
fy εc + 0.004
ρmax = ρet = 0.0281
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0049
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 0.0345m
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 95.64kN·m
øMn = 86.08kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.329 → O.K

7. Check Bending Moment Capacity (Negative)

(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
40000 40000
smax1 = 15 ( ) - 2.5cc smax2 = 12 ( )
fs fs
smax = min ( smax1 , smax2 ) = 0.554m, Nreq = 2
s = 0.0925 < 0.554m → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 200
ρmin.11 = 3 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0061
4 Mu
ρmin.2 = = 0.0079
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0061
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0281
fy εc + 0.004
ρmax = ρet = 0.0281
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0063
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 0.0432m
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 115kN·m

2025-07-04 21:03 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB2

øMn = 103kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.933 → O.K

8. Check Shear Capacity

(1) Calculate shear strength by concrete
ø = 0.750 d = 0.526m
øVc = ø 2 f'c bw d = 89.39kN
1
Vu < øVc → Shear reinforcement is not required
2
(2) Calculate shear strength by stirrup
Nleg = 2 Av1 = 0.0000710m² (#3)
Av fyt d
øVs = ø = 127kN
s
(3) Calculate ratio of shear capacity
øVn = øVc + øVs = 217kN
Vu / øVn = 0.162 → O.K
(4) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 24in ] = 0.263m
Nleg Av1
sreq = = 0.263m
Av.req
smax = min [ smax.0 sreq ] = 0.263m
s = 0.100m < smax = 0.263m → O.K

Section : MIDDLE
1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material
(1) F'c : 20,684KPa
(2) Fy : 227,600KPa
(3) Fys : 227,600KPa

3. Section
(1) Section Size : 0.300 x 0.600m (R-Section)
(2) Cover : 0.0400m
(3) Compression : Not Considered
(4) Splicing Limit : 50%

2025-07-04 21:03 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB2

0.300
0.0400

0.600
0.0400

4. Moments and Forces

(1) Mu,top : 17.68kN·m
(2) Mu,bottom : 34.12kN·m
(3) Vu : 20.56kN

5. Reinforcement
(1) Top Bar : 3-#5 (As = 0.000600m²)
Layer 1 : 3 EA (Cc = 0.0575m)
(2) Bot Bar : 4-#5 (As = 0.000800m²)
Layer 1 : 4 EA (Cc = 0.0575m)
(3) Stirrup : 2-#[email protected] (As = 0.000142m²)

6. Check Bending Moment Capacity (Positive)

(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
40000 40000
smax1 = 15 ( ) - 2.5cc smax2 = 12 ( )
fs fs
smax = min ( smax1 , smax2 ) = 0.554m, Nreq = 2
s = 0.0617 < 0.554m → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 200
ρmin.11 = 3 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0061
4 Mu
ρmin.2 = = 0.0025
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0025
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0281
fy εc + 0.004
ρmax = ρet = 0.0281
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0049
bw d
ρmin < ρ < ρmax → O.K
2025-07-04 21:03 4
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB2

(5) Calculate moment capacity

As fy
a= = 0.0345m
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 95.64kN·m
øMn = 86.08kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.396 → O.K

7. Check Bending Moment Capacity (Negative)

(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
40000 40000
smax1 = 15 ( ) - 2.5cc smax2 = 12 ( )
fs fs
smax = min ( smax1 , smax2 ) = 0.554m, Nreq = 2
s = 0.0925 < 0.554m → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 200
ρmin.11 = 3 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0061
4 Mu
ρmin.2 = = 0.0013
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0013
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0281
fy εc + 0.004
ρmax = ρet = 0.0281
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0037
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 0.0259m
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 72.32kN·m
øMn = 65.09kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.272 → O.K

8. Check Shear Capacity

(1) Calculate shear strength by concrete
ø = 0.750 d = 0.543m
øVc = ø 2 f'c bw d = 92.20kN
1
Vu < øVc → Shear reinforcement is not required
2
(2) Calculate shear strength by stirrup
Nleg = 2 Av1 = 0.0000710m² (#3)
Av fyt d
øVs = ø = 65.72kN
s
(3) Calculate ratio of shear capacity
øVn = øVc + øVs = 158kN
Vu / øVn = 0.130 → O.K
(4) Calculate spacing limits for reinforcement
2025-07-04 21:03 5
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB2

smax.0 = min [ d/2, 24in ] = 0.271m

Nleg Av1
sreq = = 0.271m
Av.req
smax = min [ smax.0 sreq ] = 0.271m
s = 0.200m < smax = 0.271m → O.K

Section : END(J)
1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material
(1) F'c : 20,684KPa
(2) Fy : 227,600KPa
(3) Fys : 227,600KPa

3. Section
(1) Section Size : 0.300 x 0.600m (R-Section)
(2) Cover : 0.0400m
(3) Compression : Not Considered
(4) Splicing Limit : 50%

0.300
0.0400

0.600
0.0400

4. Moments and Forces

(1) Mu,top : 79.64kN·m
(2) Mu,bottom : 17.65kN·m
(3) Vu : 34.44kN

5. Reinforcement
(1) Top Bar : 5-#5 (As = 0.001000m²)
2025-07-04 21:03 6
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB2

Layer 1 : 3 EA (Cc = 0.0575m)

Layer 2 : 2 EA (Cc = 0.0987m)
(2) Bot Bar : 4-#5 (As = 0.000800m²)
Layer 1 : 4 EA (Cc = 0.0575m)
(3) Stirrup : 2-#[email protected] (As = 0.000142m²)

6. Check Bending Moment Capacity (Positive)

(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
40000 40000
smax1 = 15 ( ) - 2.5cc smax2 = 12 ( )
fs fs
smax = min ( smax1 , smax2 ) = 0.554m, Nreq = 2
s = 0.0617 < 0.554m → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 200
ρmin.11 = 3 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0061
4 Mu
ρmin.2 = = 0.0013
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0013
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0281
fy εc + 0.004
ρmax = ρet = 0.0281
(4) Check ratio of tensile reinforcement
As
ρ= = 0.0049
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 0.0345m
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 95.64kN·m
øMn = 86.08kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.205 → O.K

7. Check Bending Moment Capacity (Negative)

(1) Calculate design parameter
β1 = 0.850
(2) Check space of rebar
40000 40000
smax1 = 15 ( ) - 2.5cc smax2 = 12 ( )
fs fs
smax = min ( smax1 , smax2 ) = 0.554m, Nreq = 2
s = 0.0925 < 0.554m → O.K
(3) Calculate required ratio of reinforcement
( f'c )1/2 200
ρmin.11 = 3 ρmin.12 =
fy fy
ρmin.1 = max ( ρmin.11 , ρmin.12 ) = 0.0061
4 Mu
ρmin.2 = = 0.0064
3 ø fy bd(d-a/2)
ρmin = min ( ρmin1 , ρmin2 ) = 0.0061
f'c εc
ρεt = 0.85 β1 ( )( ) = 0.0281
fy εc + 0.004
2025-07-04 21:03 7
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : FTB2

ρmax = ρet = 0.0281

(4) Check ratio of tensile reinforcement
As
ρ= = 0.0063
bw d
ρmin < ρ < ρmax → O.K
(5) Calculate moment capacity
As fy
a= = 0.0432m
0.85 f'c bw
ø = 0.900
Mn = As fy (d - a/2) = 115kN·m
øMn = 103kN·m
(6) Calculate ratio of moment capacity
Mu / øMn = 0.771 → O.K

8. Check Shear Capacity

(1) Calculate shear strength by concrete
ø = 0.750 d = 0.526m
øVc = ø 2 f'c bw d = 89.39kN
1
Vu < øVc → Shear reinforcement is not required
2
(2) Calculate shear strength by stirrup
Nleg = 2 Av1 = 0.0000710m² (#3)
Av fyt d
øVs = ø = 127kN
s
(3) Calculate ratio of shear capacity
øVn = øVc + øVs = 217kN
Vu / øVn = 0.159 → O.K
(4) Calculate spacing limits for reinforcement
smax.0 = min [ d/2, 24in ] = 0.263m
Nleg Av1
sreq = = 0.263m
Av.req
smax = min [ smax.0 sreq ] = 0.263m
s = 0.100m < smax = 0.263m → O.K

2025-07-04 21:03 8
midas Gen RC Beam Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-08-25.rcs

------------------------------------------------------------------------------------------
midas Gen - RC-Beam Checking [ NSCP 2015 ] Gen 2021
==========================================================================================

+============================================================+
| MIDAS(Modeling, Integrated Design & Analysis Software) |
| midas Gen - Design & checking system for windows |
+============================================================+
| RC-Member(Beam/Column/Brace/Wall) Analysis and Design |
| Based On Eurocode2:04, Eurocode2, ACI318-14, |
| ACI318M-14, ACI318-11, ACI318-08, ACI318-05, |
| ACI318-02, ACI318-99, ACI318-95, ACI318-89, |
| NSR-10, CSA-A23.3-94, BS8110-97, NSCP 2015 |
| |
| |
| |
| |
| (c)SINCE 1989 |
+============================================================+
| MIDAS Information Technology Co.,Ltd. (MIDAS IT) |
| MIDAS IT Design Development Team |
+============================================================+
| HomePage : www.MidasUser.com |
+============================================================+
| Gen 2021 |
+============================================================+

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/11/2025 22:58
http://www.MidasUser.com
midas Gen RC Beam Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-08-25.rcs

25 1 DL( 0.900) + RS-M(RS)(-1.000)

26 1 DL( 0.900) + RS-O(RS)(-1.000)
27 2 DL( 1.000)
28 2 DL( 1.000) + LL( 1.000)
29 2 DL( 1.000) + LL( 0.750)
30 2 DL( 1.000) + WL-X( 0.600)
31 2 DL( 1.000) + WL-Y( 0.600)
32 2 DL( 1.000) + WL-X(-0.600)
33 2 DL( 1.000) + WL-Y(-0.600)
34 2 DL( 1.000) + EL-X( 0.714)
35 2 DL( 1.000) + EL-Y( 0.714)
36 2 DL( 1.000) + EL-X(-0.714)
37 2 DL( 1.000) + EL-Y(-0.714)
38 2 DL( 1.000) + RS-M(RS)( 0.714)
39 2 DL( 1.000) + RS-O(RS)( 0.714)
40 2 DL( 1.000) + RS-M(RS)(-0.714)
41 2 DL( 1.000) + RS-O(RS)(-0.714)
--------------------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/11/2025 22:58
http://www.MidasUser.com
midas Gen RC Beam Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-08-25.rcs

*.midas Gen - RC-BEAM Analysis/Design Program.

*.PROJECT :
*.DESIGN CODE : NSCP 2015, *.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in SI units in the report)
*.MEMBER : Member Type = BEAM, MEMB = 1791

*.DESCRIPTION OF BEAM DATA (iSEC = 12) : B-1

Section Type : Rectangle (RECT)
Beam Length (Span) = 7.275 m.
Section Depth (Hc) = 0.800 m.
Section Width (Bc) = 0.400 m.
Concrete Strength (fc) = 20684.278 KPa.
Modulus of Elasticity (Ec) = 21375586.730 KPa.
Main Rebar Strength (fy) = 275790.378 KPa.
Stirrups Strength (fys) = 275790.378 KPa.
Modulus of Elasticity (Es) = 200000000.000 KPa.

*.FORCES AND MOMENTS AT CHECK POINT <I> :

Positive Bending Moment P-Mu = 514.36 kN-m., LCB = 19
Negative Bending Moment N-Mu = 688.27 kN-m., LCB = 9
Shear Force Vu = 237.16 kN. , LCB = 9

*.REINFORCEMENT PATTERN :
------------------------------------------------------------
Location i di( m.) Rebar Asi( m^2.)
------------------------------------------------------------
Top 1 0.083 5-P32/ 2-P20 0.00465
Bottom 2 0.708 3-P32/ 2-P25 0.00339
------------------------------------------------------------
Stirrups : P10

===============================================================================
[[[*]]] ANALYZE POSITIVE BENDING MOMENT CAPACITY.
===============================================================================

( ). Compute design parameter.

-. beta1 = 0.8500 ( fc < 28 MPa.)

( ). Check spacing of reinforcement closet to the tensile face.

-. fs = (2/3)*fy =1.839e+05 KPa.
-. cc = 0.060 m.
-. s1 = 380*(280/fs) - 2.5Cc = 0.428 m.
-. s2 = 300*(280/fs) = 0.457 m.
-. smax = MIN[ s1, s2 ] = 0.428 m.
-. s = 0.124 m. < smax ---> O.K.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/11/2025 22:58
http://www.MidasUser.com
midas Gen RC Beam Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-08-25.rcs

( ). Compute required ratio of reinforcement.

-. k = 1.000000
-. Rhomi1 = MAX[ 0.25*SQRT(fc)/fy, 1.4/fy ] = 0.0051
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ] = 0.0151
-. Rhomin = MIN[ Rhomi1, Rhomi2 ] = 0.0051
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) = 0.0232
-. Rhomax = k*Rho_et = 0.0232

( ). Check ratio of tensile reinforcement.

-. Rho = Ast/(bw*d) = 0.0120
-. Rhomin < Rho < Rhomax ---> O.K !

( ). Check maximum permissible tensile reinforcement.

-. cb = (0.003/(0.003+0.004))*d = 0.304 m.
-. c_max = cb = 0.304 m.
-. a_max = beta1*c_max = 0.258 m.
-. Cc_max = 0.85*fc*(bw*a_max) = 1814.66 kN.
-. esc = 0.003*(c_max-dc)/c_max = 0.002
-. fsc = Es*esc = 275790.378 KPa.
-. Cs = (fsc-0.85*fc)*Asc = 1200.56 kN.
-. Ts_max = Cc_max+Cs = 3015.22 kN.
-. Asmax = Ts_max/fy = 0.011 m^2.
-. Ast = 0.003 m^2. < Asmax ---> O.K !

( ). Check compression steel yield condition.

-. cy = (0.003/(0.003-fy/Es))*dc = 0.154 m.
-. Ccy = 0.85*fc*bw*(beta1*cy) = 919.23 kN.
-. Csy = (fy-0.85*fc)*Asc = 1200.56 kN.
-. Tsy = Ccy+Csy = 2119.79 kN.
-. Asy = Tsy/fy = 0.008 m^2.
-. Ast = 0.003 m^2. < Asy ---> Compression steel does not yield.

( ). Search for neutral axis...... Unit : kN., m.

---------------------------------------------------------------------
Trial c Cc + Cs = CcCs Ts Ratio
---------------------------------------------------------------------
1-st 0.354 2117.10 1200.56 3317.66 936.17 -154.39
2-nd 0.177 1058.55 1200.56 2259.11 936.17 -41.31
3-rd 0.089 529.28 171.69 700.96 936.17 74.88
4-th 0.133 793.91 962.62 1756.54 936.17 12.37
5-th 0.111 661.59 613.55 1275.15 936.17 63.79
6-th 0.100 595.44 380.83 976.27 936.17 95.72
7-th 0.094 562.36 325.69 888.05 936.17 94.86
8-th 0.097 578.90 396.09 974.99 936.17 95.85
9-th 0.095 570.63 361.40 932.03 936.17 99.56
---------------------------------------------------------------------

( ). Compute allowable moment capacity.

-. a = beta1*c = 0.081 m.
-. esc = 0.003*(c-dc)/c = 0.000389
-. fsc = MIN[ Es*esc, fy ] = 77727.712 KPa.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/11/2025 22:58
http://www.MidasUser.com
midas Gen RC Beam Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-08-25.rcs

-. Cs = fsc*Asc = 361.40 kN.

-. Cc = 0.85*fc*bw*a = 570.63 kN.
-. Mn = Cc*(d-a/2)+Cs*(d-dc) = 607.00 kN-m.
-. phi = 0.90
-. phiMn = phi*Mn = 546.30 kN-m.

( ). Check ratio of positive moment capacity.

-. Rat_P = Mu/phiMn = 0.942 < 1.000 ---> O.K.

===============================================================================
[[[*]]] ANALYZE NEGATIVE BENDING MOMENT CAPACITY.
===============================================================================

( ). Compute design parameter.

-. beta1 = 0.8500 ( fc < 28 MPa.)

( ). Check spacing of reinforcement closet to the tensile face.

-. fs = (2/3)*fy =1.839e+05 KPa.
-. cc = 0.060 m.
-. s1 = 380*(280/fs) - 2.5Cc = 0.428 m.
-. s2 = 300*(280/fs) = 0.457 m.
-. smax = MIN[ s1, s2 ] = 0.428 m.
-. s = 0.062 m. < smax ---> O.K.

( ). Compute required ratio of reinforcement.

-. k = 1.000000
-. Rhomi1 = MAX[ 0.25*SQRT(fc)/fy, 1.4/fy ] = 0.0051
-. Rhomi2 = (4/3)*Mu/[ phi*fy*b*d*(d-a/2) ] = 0.0204
-. Rhomin = MIN[ Rhomi1, Rhomi2 ] = 0.0051
-. Rho_et = 0.85*beta1*(fc/fy)*(0.003/(0.003+0.004)) = 0.0232
-. Rhomax = k*Rho_et = 0.0232

( ). Check ratio of tensile reinforcement.

-. Rho = Ast/(bw*d) = 0.0162
-. Rhomin < Rho < Rhomax ---> O.K !

( ). Check maximum permissible tensile reinforcement.

-. cb = (0.003/(0.003+0.004))*d = 0.307 m.
-. c_max = cb = 0.307 m.
-. a_max = beta1*c_max = 0.261 m.
-. Cc_max = 0.85*fc*(bw*a_max) = 1836.64 kN.
-. esc = 0.003*(c_max-dc)/c_max = 0.002
-. fsc = Es*esc = 275790.378 KPa.
-. Cs = (fsc-0.85*fc)*Asc = 876.49 kN.
-. Ts_max = Cc_max+Cs = 2713.13 kN.
-. Asmax = Ts_max/fy = 0.010 m^2.
-. Ast = 0.005 m^2. < Asmax ---> O.K !

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/11/2025 22:58
http://www.MidasUser.com
midas Gen RC Beam Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-08-25.rcs

( ). Check compression steel yield condition.

-. cy = (0.003/(0.003-fy/Es))*dc = 0.170 m.
-. Ccy = 0.85*fc*bw*(beta1*cy) = 1014.16 kN.
-. Csy = (fy-0.85*fc)*Asc = 876.49 kN.
-. Tsy = Ccy+Csy = 1890.64 kN.
-. Asy = Tsy/fy = 0.007 m^2.
-. Ast = 0.005 m^2. < Asy ---> Compression steel does not yield.

( ). Search for neutral axis...... Unit : kN., m.

---------------------------------------------------------------------
Trial c Cc + Cs = CcCs Ts Ratio
---------------------------------------------------------------------
1-st 0.358 2142.75 876.49 3019.24 1282.31 -35.45
2-nd 0.179 1071.38 876.49 1947.86 1282.31 48.10
3-rd 0.090 535.69 -46.81 488.88 1282.31 38.13
4-th 0.134 803.53 588.01 1391.54 1282.31 91.48
5-th 0.112 669.61 310.21 979.82 1282.31 76.41
6-th 0.123 736.57 461.74 1198.31 1282.31 93.45
7-th 0.129 770.05 527.62 1297.67 1282.31 98.80
8-th 0.126 753.31 495.41 1248.72 1282.31 97.38
9-th 0.127 761.68 511.69 1273.37 1282.31 99.30
---------------------------------------------------------------------

( ). Compute allowable moment capacity.

-. a = beta1*c = 0.108 m.
-. esc = 0.003*(c-dc)/c = 0.000842
-. fsc = MIN[ Es*esc, fy ] = 168323.931 KPa.
-. Cs = (fsc-0.85*fc)*Asc = 511.69 kN.
-. Cc = 0.85*fc*bw*a = 761.68 kN.
-. Mn = Cc*(d-a/2)+Cs*(d-dc) = 824.74 kN-m.
-. phi = 0.90
-. phiMn = phi*Mn = 742.26 kN-m.

( ). Check ratio of negative moment capacity.

-. Rat_N = Mu/phiMn = 0.927 < 1.000 ---> O.K.

===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY.
===============================================================================

( ). Compute shear strength of concrete.

-. Vu = 237.16 kN.
-. Vc = 1/6*SQRT(fc)*bw*d = 217.37 kN.
-. phi = 0.75
-. phiVc = phi*Vc = 163.02 kN.
-. Vu > phiVc ---> Shear reinforcement is required.

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/11/2025 22:58
http://www.MidasUser.com
midas Gen RC Beam Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-06-08-25.rcs

( ). Compute required shear reinforcement. ( Av1 = 0.00008 m^2. )

-. Vs = (Vu-phiVc)/phi = 98.85 kN.
-. 1/3*SQRT(fc)*bw*d = 434.73 kN.
-. 2/3*SQRT(fc)*bw*d = 869.47 kN.
-. Vs < 1/3*SQRT(fc)*bw*d ---> O.K !
-. Avmin1 = 0.35*bw/fys = 0.00051 m^2/m.
-. Avmin2 = 0.062*SQRT(fc)*bw/fys = 0.00041 m^2/m.
-. Avmin = MAX[ Avmin1, Avmin2 ] = 0.00051 m^2/m.
-. Avreq = Vs/(fys*d) = 0.00050 m^2/m.
-. Av = MAX[ Avmin, Avreq ] = 0.00051 m^2/m.
-. N_leg = 2
-. Maximum spacing smax = MIN[ d/2, 600 mm ] = 0.358 m.
-. Calculate spacing s1 = N_leg*Av1 / Av = 0.30944 m.
-. Applied spacing s = MIN[ smax, s1 ] = 0.309 m.

===============================================================================
[[[*]]] CHECK CRACK WIDTHS.
===============================================================================

Modeling, Integrated Design & Analysis Software Print Date/Time : 06/11/2025 22:58
http://www.MidasUser.com
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : S1

1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material Ly
(1) F'c : 20,684KPa
(2) Fy : 227,600KPa
y
3. Design Load
(1) Dead Load : 3.500kN/m² x

(2) Live Load : 2.394kN/m² B1

4. Section Size
Y1
(1) Span(X) : 3.320m
Lx

(2) Span(Y) : 6.000m Y2

(3) Thickness : 0.125m

B4
(4) Cover : 0.0200m
(5) Use clear span : Yes B2

5. Slab Type & Support

X1 X2
(1) Slab Type : 2-Way Slab
(2) Support Type : Case-2
(3) Boundary Beams : B1 : 0.140 x 0.360 / B2 : 0.152 x 0.450 / B3 : 0.152 x 0.450 / B4 : 0.152 x 0.450

6. Determine the design type of slab

(1) Calculate span ratio [ Use clear span ]
Lx = 3.174m
Ly = 5.848m
Span Ratio( Lx / Ly ) = 0.543 >= 0.5 -> 2-Way Slab

7. Check Load
(1) Calculate factored load
LCB01 = 4.900kN/m² ( 1.4D )
LCB02 = 8.030kN/m² ( 1.2D+1.6L )
ωu = 8.030kN/m²

8. Check Thickness of Slab

(1) Calculate factors
β = lny / lnx = 1.842
αm = 2.644 (α1 = 1.842, α2 = 4.147, α3 = 2.294, α4 = 2.294)
(2) Calculate minimum thickness required
ln (0.8 + (fy / 200000))
hreq = = 0.107m
36 + 9β
h = 0.125m > hreq = 0.107m → O.K

9. Check Capacity of Slab

(1) Calculate Moment & Shear [ Direction X ]
Check Items TOP MIDDLE BOTTOM
Bar-1 #[email protected] #[email protected] #[email protected]
Bar-2 #[email protected] #[email protected] #[email protected]
Bar-3 - - -
Moment Coefficient (DL) 0.000 0.0353 0.000
Moment Coefficient (LL) 0.000 0.0626 0.000
Moment Coefficient (FL) 0.0843 0.000 0.0843

2025-07-01 18:49 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : S1

Shear Coefficient 0.923 0.000 0.923

Mu (kN·m/m) 81.84 46.91 81.84
Vu (kN/m) 141 0.000 141
øMn (kN·m/m) 113 57.40 113
øVn (kN/m) 681 681 681
Mu / øMn 0.724 0.817 0.724
Vu / øVn 0.207 0.000 0.207

(2) Calculate Moment & Shear [ Direction Y ]

Check Items LEFT CENTER RIGHT
Bar-1 #[email protected] #[email protected] #[email protected]
Bar-2 #[email protected] #[email protected] #[email protected]
Bar-3 - - -
Moment Coefficient (DL) 0.000 0.00285 0.000
Moment Coefficient (LL) 0.000 0.00570 0.000
Moment Coefficient (FL) 0.00685 0.000 0.00685
Shear Coefficient 0.0770 0.000 0.0770
Mu (kN·m/m) 22.57 13.87 22.57
Vu (kN/m) 21.70 0.000 21.70
øMn (kN·m/m) 102 51.86 102
øVn (kN/m) 617 617 617
Mu / øMn 0.221 0.268 0.221
Vu / øVn 0.0352 0.000 0.0352

2025-07-01 18:49 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : S2

1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
Ly
[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material
(1) F'c : 20,684KPa
y
(2) Fy : 227,600KPa
x
3. Design Load
B1
(1) Dead Load : 3.500kN/m²
(2) Live Load : 2.394kN/m²

4. Section Size
(1) Span(X) : 3.820m Y1
(2) Span(Y) : 4.000m
Lx

Y2
(3) Thickness : 0.125m
(4) Cover : 0.0200m
(5) Use clear span : Yes B3

B4
5. Slab Type & Support
(1) Slab Type : 2-Way Slab B2
(2) Support Type : Case-2
X1 X2
(3) Boundary Beams : B1 : 0.146 x 0.400 / B2 : 0.300 x 0.588 / B3 : 0.300 x 0.588 / B4 : 0.300 x 0.588

6. Determine the design type of slab

(1) Calculate span ratio [ Use clear span ]
Lx = 3.597m
Ly = 3.700m
Span Ratio( Lx / Ly ) = 0.972 >= 0.5 -> 2-Way Slab

7. Check Load
(1) Calculate factored load
LCB01 = 4.900kN/m² ( 1.4D )
LCB02 = 8.030kN/m² ( 1.2D+1.6L )
ωu = 8.030kN/m²

8. Check Thickness of Slab

(1) Calculate factors
β = lny / lnx = 1.029
αm = 11.10 (α1 = 2.357, α2 = 14.44, α3 = 13.79, α4 = 13.79)
(2) Calculate minimum thickness required
ln (0.8 + (fy / 200000))
hreq = = 0.0889m
36 + 9β
h = 0.125m > hreq = 0.0889m → O.K

9. Check Capacity of Slab

(1) Calculate Moment & Shear [ Direction X ]
Check Items TOP MIDDLE BOTTOM
Bar-1 #[email protected] #[email protected] #[email protected]
Bar-2 #[email protected] #[email protected] #[email protected]
Bar-3 - - -
Moment Coefficient (DL) 0.000 0.0191 0.000
Moment Coefficient (LL) 0.000 0.0287 0.000
Moment Coefficient (FL) 0.0478 0.000 0.0478

2025-07-02 14:33 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : S2

Shear Coefficient 0.528 0.000 0.528

Mu (kN·m/m) 59.60 29.52 59.60
Vu (kN/m) 91.51 0.000 91.51
øMn (kN·m/m) 113 57.40 113
øVn (kN/m) 681 681 681
Mu / øMn 0.527 0.514 0.527
Vu / øVn 0.134 0.000 0.134

(2) Calculate Moment & Shear [ Direction Y ]

Check Items LEFT CENTER RIGHT
Bar-1 #[email protected] #[email protected] #[email protected]
Bar-2 #[email protected] #[email protected] #[email protected]
Bar-3 - - -
Moment Coefficient (DL) 0.000 0.0169 0.000
Moment Coefficient (LL) 0.000 0.0259 0.000
Moment Coefficient (FL) 0.0428 0.000 0.0428
Shear Coefficient 0.472 0.000 0.472
Mu (kN·m/m) 56.41 27.93 56.41
Vu (kN/m) 84.15 0.000 84.15
øMn (kN·m/m) 102 51.86 102
øVn (kN/m) 617 617 617
Mu / øMn 0.553 0.539 0.553
Vu / øVn 0.136 0.000 0.136

2025-07-02 14:33 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BS1

1. General Information
Design Code Code Unit F'c Fy
ACI318-14 lbf, in 20,684KPa 227,600KPa

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Design Forces
(1) Service Load
Ps Msx Msy
0.000kN 2.100kN·m 1.000kN·m

(2) Factored Load

Pu Mux Muy
0.000kN 5.900kN·m 2.000kN·m

(3) Surcharge Load & Self Weight

Self Weight Surface Load Weight Density Soil Height
Considered - - -

3. Foundation
Depth Cover Lx Ly fe
0.200m 0.0800m 12.00m 12.00m 80.00kN/m²

4. Column
Shape B D Eccentricity(X) Eccentricity(Y)
Rectangle 0.000m 0.000m 0.000m 0.000m

2025-07-02 15:15 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BS1

6.00 6.00 6.00

Y1
6.00

X1
0.20

5. Rebar
Layer-1 (Y) Layer-2 (Y) Layer-1 (X) Layer-2 (X)
#[email protected] - #[email protected] -

6. Check Capacity
Check Items Calculated Criteria Ratio
Soil Capacity (kN/m²) 4.566 80.00 0.0571
qu,max (kN/m²) 5.494 - -
qu,min (kN/m²) 5.439 - -
One Way Shear-X (kN) 0.000 783 0.000
One Way Shear-Y (kN) 0.000 719 0.000
Two Way Shear (kN) 0.000 60.18 0.000
Moment-X Direction(Muy, kN·m/m) 0.0254 2.933 0.00866
Moment-Y Direction(Mux, kN·m/m) 0.0749 2.685 0.0279
Rebar Space-Y Direction(sx, m) 0.170 0.457 0.372
Rebar Space-X Direction(sy, m) 0.170 0.457 0.372

2025-07-02 15:15 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : RAMP SLAB

1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material Ly

(1) F'c : 20,684KPa

(2) Fy : 227,600KPa
y
3. Design Load
x
(1) Dead Load : 3.500kN/m²
B1
(2) Live Load : 4.800kN/m²

4. Section Size
Y1
(1) Span(X) : 7.000m
Lx

(2) Span(Y) : 12.00m Y2

(3) Thickness : 0.300m

B4
(4) Cover : 0.0200m
(5) Use clear span : No B2
5. Slab Type & Support
(1) Slab Type : 2-Way Slab X1 X2

(2) Support Type : Case-2

(3) Boundary Beams : B1 : 0.400 x 0.800 / B2 : 0.400 x 0.800 / B3 : 0.400 x 0.800 / B4 : 0.400 x 0.800

6. Determine the design type of slab

(1) Calculate span ratio
Lx = 7.000m
Ly = 12.00m
Span Ratio( Lx / Ly ) = 0.583 >= 0.5 -> 2-Way Slab

7. Check Load
(1) Calculate factored load
LCB01 = 4.900kN/m² ( 1.4D )
LCB02 = 11.88kN/m² ( 1.2D+1.6L )
ωu = 11.88kN/m²

8. Check Thickness of Slab

(1) Calculate factors
β = lny / lnx = 1.758
αm = 1.457 (α1 = 1.841, α2 = 1.841, α3 = 1.074, α4 = 1.074)
(2) Calculate minimum thickness required
ln (0.8 + (fy / 200000))
hreq = = 0.238m
36 + 5β(αm - 0.2))
h = 0.300m > hreq = 0.238m → O.K

9. Check Capacity of Slab

(1) Calculate Moment & Shear [ Direction X ]
Check Items TOP MIDDLE BOTTOM
Bar-1 #[email protected] #[email protected] #[email protected]
Bar-2 #[email protected] #[email protected] #[email protected]
Bar-3 - - -
Moment Coefficient (DL) 0.000 0.0343 0.000
Moment Coefficient (LL) 0.000 0.0594 0.000
Moment Coefficient (FL) 0.0820 0.000 0.0820

2025-07-01 18:50 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : RAMP SLAB

Shear Coefficient 0.900 0.000 0.900

Mu (kN·m/m) 573 353 573
Vu (kN/m) 449 0.000 449
øMn (kN·m/m) 653 653 653
øVn (kN/m) 1,849 1,849 1,849
Mu / øMn 0.878 0.541 0.878
Vu / øVn 0.243 0.000 0.243

(2) Calculate Moment & Shear [ Direction Y ]

Check Items LEFT CENTER RIGHT
Bar-1 #[email protected] #[email protected] #[email protected]
Bar-2 #[email protected] #[email protected] #[email protected]
Bar-3 - - -
Moment Coefficient (DL) 0.000 0.00366 0.000
Moment Coefficient (LL) 0.000 0.00666 0.000
Moment Coefficient (FL) 0.00898 0.000 0.00898
Shear Coefficient 0.0998 0.000 0.0998
Mu (kN·m/m) 184 115 184
Vu (kN/m) 85.36 0.000 85.36
øMn (kN·m/m) 614 614 614
øVn (kN/m) 1,741 1,741 1,741
Mu / øMn 0.300 0.187 0.300
Vu / øVn 0.0490 0.000 0.0490

2025-07-01 18:50 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : ST01

1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Design Data
(1) Material
F'c : 20,684KPa
Fy : 227,600KPa
Fys : 400,000KPa
(2) Design Load
DL (Stair) : 3.500kN/m²
DL (Landing) : 3.500kN/m²
Live Load : 2.400kN/m²
2.000
0.900 0.900
1.800

1.950 6.000 1.950

(3) Support : By Landing
(4) Thickness
Stair : 0.150m
Landing : 0.125m
Cover : 0.0200m
(5) Length
Landing(Left) : 1.950m
Landing(Right) : 1.950m
Stair : 6.000m
(6) Size
Height : 2.000m
Width : 1.800m

3. Calculate Design Load

(1) Stair
ωu = 1.2ωD + 1.6ωL = 8.040kN/m²
(2) Landing
ωu = 1.2ωD + 1.6ωL = 8.040kN/m²

4. Moment Diagram

2025-07-01 18:37 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : ST01

Mu = 0.000

Vu = 7.352

Vu = 0.000

Mu = 11.62
Vu = -5.782 Vu = -7.352

Mu = Vu
0.000
= Mu
0.000
= 0.000 Mu = 0.000
Mu = 2.602
Vu = 5.782

5. Shear Force Diagram

Mu = 0.000

Vu = 7.352

Vu = 0.000

Mu = 11.62
Vu = -5.782 Vu = -7.352

Mu = 0.000
Vu = 0.000
Mu = 0.000 Mu = 0.000
Mu = 2.602
Vu = 5.782

6. Check Stair
(1) Moment Capacity
Rebar Land(L) Stair Land(R) Min. Land Min. Stair
Mu (kN·m/m) 2.602 11.62 2.602 ρ = 0.00200 ρ = 0.00200
#3 @0.166 @0.0437 @0.166 @0.457(0.554) @0.457(0.554)
#3+4 @0.230 @0.0607 @0.230 @0.457(0.554) @0.457(0.554)
#4 @0.297 @0.0783 @0.297 @0.457(0.554) @0.457(0.554)
#4+5 @0.372 @0.0983 @0.372 @0.457(0.554) @0.457(0.554)
#5 @0.452 @0.119 @0.452 @0.457(0.554) @0.457(0.554)

(2) Shear Capacity

- Land(L) Stair Land(R)
Vu (kN/m) -5.782 -7.352 5.782
øVn (kN/m) 15.94 19.70 15.94
Vu / øVn 0.363 0.373 0.363

2025-07-01 18:37 2
MIDASIT http://www.midasuser.com

RC BASEWALL LIST

BASEWALL DETAIL ( BW1 )

1F GL0.000
GL

#5@150 #4@200
3000 (t=200)

#4@200 #4@200
1000

B1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BW1

1. General Information
(1) Design Code : ACI318-14
1F
(2) Code Unit : lbf, in G.L GL0

[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material
(1) F'c : 20,684KPa

3.000 ( t = 0.200 )
(2) Fy : 227,600KPa
(3) Fys : 227,600KPa

3. Section
(1) Basewall Type : 1 Way
(2) Cover : 0.0400m
(3) Story Information
B1
Story(B1) : H=3.000m, THK.=0.200m

4. Boundary Condition
(1) Top : Pin (Factor = 0.000)
(2) Bottom : Fix (Factor = 1.000)

5. Soil Load
(1) Surcharge Load : 0.000kip/ft²
(2) 1st Floor Level : GL+0.000ft
(3) Water Level : GL+0.000ft
(4) Live Factor : 1.600
(5) Soil Factor : 1.600
(6) Water Factor : 1.600
(7) Soil Property
Use N-Value : No
Use Active Soil Pressure : No
No. H(ft) Angle Density(kip/ft³)
1 32.81 30.00 0.115
2 32.81 30.00 0.115
3 32.81 30.00 0.115
4 32.81 30.00 0.115
5 32.81 30.00 0.115
6 32.81 30.00 0.115
7 32.81 30.00 0.115
8 32.81 30.00 0.115

6. Calculate soil pressure

Level Press.
Posi. Ko Equation
( ft ) ( kip/ft² )
Layer-01 Top 0.500 0.000 1.600x0.500x0.000 + 1.600x0.500x0.000 0.000
Layer-01 Bot 0.500 32.81 1.600x0.500x0.000 + 1.600x0.500x1.711 + 1.600x2.048 4.646
Layer-02 Top 0.500 32.81 1.600x0.500x0.000 + 1.600x0.500x1.711 + 1.600x2.048 4.646
Layer-02 Bot 0.500 65.62 1.600x0.500x0.000 + 1.600x0.500x3.422 + 1.600x4.096 9.292
Layer-03 Top 0.500 65.62 1.600x0.500x0.000 + 1.600x0.500x3.422 + 1.600x4.096 9.292
Layer-03 Bot 0.500 98.43 1.600x0.500x0.000 + 1.600x0.500x5.134 + 1.600x6.144 13.94
Layer-04 Top 0.500 98.43 1.600x0.500x0.000 + 1.600x0.500x5.134 + 1.600x6.144 13.94
Layer-04 Bot 0.500 131 1.600x0.500x0.000 + 1.600x0.500x6.845 + 1.600x8.193 18.58
Layer-05 Top 0.500 131 1.600x0.500x0.000 + 1.600x0.500x6.845 + 1.600x8.193 18.58
2025-07-01 18:39 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BW1

Layer-05 Bot 0.500 164 1.600x0.500x0.000 + 1.600x0.500x8.556 + 1.600x10.24 23.23

Layer-06 Top 0.500 164 1.600x0.500x0.000 + 1.600x0.500x8.556 + 1.600x10.24 23.23
Layer-06 Bot 0.500 197 1.600x0.500x0.000 + 1.600x0.500x10.27 + 1.600x12.29 27.88
Layer-07 Top 0.500 197 1.600x0.500x0.000 + 1.600x0.500x10.27 + 1.600x12.29 27.88
Layer-07 Bot 0.500 230 1.600x0.500x0.000 + 1.600x0.500x11.98 + 1.600x14.34 32.52
Layer-08 Top 0.500 230 1.600x0.500x0.000 + 1.600x0.500x11.98 + 1.600x14.34 32.52
Layer-08 Bot 0.500 262 1.600x0.500x0.000 + 1.600x0.500x13.69 + 1.600x16.39 37.17

1F( GL+0.000 ) GL0 G.L

γ = 18.00
3.000

ф = 30.00
Ko = 0.500

B1( GL-3.000 )
66.74

[ Unit ] kN/m² γ : kN/m³

7. Check Moment Capacity [ Direction Y ]

Mu = 0.000

Mu = 5.460

Mu = -12.17

(1) Story : B1
- Top Center Bottom Remark
Rebar1 #[email protected] #[email protected] #[email protected] -
Rebar2 - - #[email protected] -
Layer(s) -
Mu(kN·m/m) 1.214 5.460 -12.17 -
øMn(kN·m/m) 5.445 10.88 15.63 -
Ratio 0.223 0.502 0.778 -
Rebar Length(m) - - 0.400 -
Rebar Space(m) 0.361 0.271 0.158 smax = 0.554m

8. Check Shear Capacity [ Direction Y ]

2025-07-01 18:39 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BW1

Vu = -6.115
Vu = -5.979

Vu = 20.46
Vu = 24.40

(1) Story : B1
- Top Center Bottom Remark
Vu(kN/m) -6.115 - 24.40 -
Vucritical -5.979 - 20.46 -
øVc(kN/m) 24.34 - 24.34 -
øVs(kN/m) 0.000 - 0.000 -
øVn(kN/m) 24.34 - 24.34 -
Ratio 0.246 - 0.841 -
Rebar - - - -
Reinf. Length(m) - - - -

2025-07-01 18:39 3
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

------------------------------------------------------------------------------------------
midas Gen - RC-Column Checking [ NSCP 2015 ] Gen 2021
==========================================================================================

+============================================================+
| MIDAS(Modeling, Integrated Design & Analysis Software) |
| midas Gen - Design & checking system for windows |
+============================================================+
| RC-Member(Beam/Column/Brace/Wall) Analysis and Design |
| Based On Eurocode2:04, Eurocode2, ACI318-14, |
| ACI318M-14, ACI318-11, ACI318-08, ACI318-05, |
| ACI318-02, ACI318-99, ACI318-95, ACI318-89, |
| NSR-10, CSA-A23.3-94, BS8110-97, NSCP 2015 |
| |
| |
| |
| |
| (c)SINCE 1989 |
+============================================================+
| MIDAS Information Technology Co.,Ltd. (MIDAS IT) |
| MIDAS IT Design Development Team |
+============================================================+
| HomePage : www.MidasUser.com |
+============================================================+
| Gen 2021 |
+============================================================+

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/02/2025 14:49
http://www.MidasUser.com
Gen 2021 - 1 / 12 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

25 1 DL( 0.900) + RS-M(RS)(-1.000)

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/02/2025 14:49
http://www.MidasUser.com
Gen 2021 - 2 / 12 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

*.midas Gen - RC-COLUMN Analysis/Design Program.

*.PROJECT :
*.DESIGN CODE : NSCP 2015, *.UNIT SYSTEM : kN, m
(Note. Nonhomogenous equation in the code are written in SI units in the report)
*.MEMBER : Member Type = COLUMN , MEMB = 1008, LCB = 22, POS = J

*.DESCRIPTION OF COLUMN DATA (iSEC = 9) : 55x55

Section Type : Rectangular with Ties (RT)
Section Height (HTc) = 2.500 m.
Section Depth (Hc) = 0.550 m.
Section Width (Bc) = 0.550 m.
Concrete Cover to C.O.R. (do) = 0.064 m.
Concrete Strength (fc) = 20684.278 KPa.
Modulus of Elasticity (Ec) = 21375586.730 KPa.
Main Rebar Strength (fy) = 275790.378 KPa.
Ties/Spirals Strength (fys) = 275790.378 KPa.
Modulus of Elasticity (Es) = 200000000.000 KPa.

*.REBAR PATTERN = RT - 14 - 5 - P25(P32) Unit : m.

--------------------------------------------------------
i dyi dzi Rebar Asi
--------------------------------------------------------
1 -0.211 -0.211 1-P32 0.00080
2 -0.211 -0.106 1-P25 0.00049
3 -0.211 0.000 1-P25 0.00049
4 -0.211 0.106 1-P25 0.00049
5 -0.211 0.211 1-P32 0.00080
6 -0.070 0.211 1-P25 0.00049
7 0.070 0.211 1-P25 0.00049
8 0.211 0.211 1-P32 0.00080
9 0.211 0.106 1-P25 0.00049
10 0.211 0.000 1-P25 0.00049
11 0.211 -0.106 1-P25 0.00049
12 0.211 -0.211 1-P32 0.00080
13 0.070 -0.211 1-P25 0.00049
14 -0.070 -0.211 1-P25 0.00049
--------------------------------------------------------

===============================================================================
[[[*]]] CALCULATE SLENDERNESS RATIOS, MAGNIFIED FORCES/MOMENTS.
===============================================================================

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/02/2025 14:49
http://www.MidasUser.com
Gen 2021 - 3 / 12 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

( ). Factored forces/moments caused by unit load case. Unit : kN., m.

*.Load combination ID = 22
-------------------------------------------------------------------------------
Load Case Pu Myi Myj Mzi Mzj
-------------------------------------------------------------------------------
DL 109.00 9.63 0.82 10.97 -2.50
LL -0.00 0.00 0.00 0.00 0.00
DL+LL 109.00 9.63 0.82 10.97 -2.50
Others -25.95 -5.16 -174.84 -123.89 -411.23
-------------------------------------------------------------------------------
DL+LL+Others 83.04 4.47 -174.02 -112.92 -413.73
-------------------------------------------------------------------------------

( ). Compute member end moments(M1,M2). Unit : kN-m.

-. For Dead Load(DL).
My1D = 0.82, My2D = 9.63
Mz1D = 2.50, Mz2D = 10.97
-. For Gravity Load(DL+LL).
My1G = 0.82, My2G = 9.63
Mz1G = 2.50, Mz2G = 10.97
-. For Total Load(DL+LL+WL(EL)).
My1 = 4.47, My2 = 174.02
Mz1 = 112.92, Mz2 = 413.73

( ). Check slenderness ratios of BRACED/UNBRACED frame.

-. Slenderness ratio limits.
SRy(Braced) = 34 + 12*MIN(|My1/My2|,0.5) = 34.308 (Reverse curvature)
SRz(Braced) = 34 - 12*| Mz1/Mz2 | = 30.725 (Single curvature)
-. Radii of gyration.
ry = 0.30*Hc = 0.165 m.
rz = 0.30*Bc = 0.165 m.
-. Unbraced lengths.
Ly = 2.500 m.
Lz = 2.500 m.
-. Effective length factors.
Ky = 1.000
Kz = 1.000
-. SLENy = Ky*Ly/ry = 15.152 <= SRy ---> NOT SLENDER.
-. SLENz = Kz*Lz/rz = 15.152 <= SRz ---> NOT SLENDER.

( ). Moment magnification factors for major axis(DBy,DSy).

-. DBy = 1.00 (Default value)
-. DSy = 1.00 (Default value)

( ). Moment magnification factors for minor axis(DBz,DSz).

-. DBz = 1.00 (Default value)
-. DSz = 1.00 (Default value)

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/02/2025 14:49
http://www.MidasUser.com
Gen 2021 - 4 / 12 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

( ). Compute minimum moments(Mmin).

-. emin_y = 15 mm. + 0.03*Hc = 0.032 m.
-. emin_z = 15 mm. + 0.03*Bc = 0.032 m.
-. Mmin_y = Pu * emin_y = 2.62 kN-m.
-. Mmin_z = Pu * emin_z = 2.62 kN-m.

( ). Compute magnified moments. (Pos : J, Local-y : Braced, Local-z : Braced).

-. No sidesway moments.
QMb_y = My_G = 0.82 kN-m.
QMb_z = Mz_G = -2.50 kN-m.
-. Sidesway moments.
QMs_y = My_S = -174.84 kN-m.
QMs_z = Mz_S = -411.23 kN-m.
-. Compute magnified moments(Mcy,Mcz).
Mcy(No-Slender) = DBy*(QMb_y + QMs_y) = -174.02 kN-m.
Mcz(No-Slender) = DBz*(QMb_z + QMs_z) = -413.73 kN-m.

( ). Check total moment including 2nd-order effects.

-. Moments due to 1st-order effects.
Mcy-1st = 174.02 kN-m.
Mcz-1st = 413.73 kN-m.
-. Moments due to 2nd-order effects.
Mcy-2nd = DBy*(QMb_y + QMs_y) = 174.02 kN-m.
Mcz-2nd = DBz*(QMb_z + QMs_z) = 413.73 kN-m.
-. Ratio of moment due to 2nd-order effects to moment due to 1st-order effects.
Mcy-2nd / Mcy-1st = 1.0000 <= 1.4 ---> O.K ! Apply magnified moment.
Mcz-2nd / Mcz-1st = 1.0000 <= 1.4 ---> O.K ! Apply magnified moment.

( ). Design forces/moments of column(brace).

-. Axial Force (Compression) Pu = 83.04 kN.
-. Combined Bending Moment Mc = 448.84 kN-m.
-. Bending Moment about Local-y Mcy = -174.02 kN-m.
-. Bending Moment about Local-z Mcz = -413.73 kN-m.
-. Shear Force of Local-y Vuy = 123.95 kN.
-. Shear Force of Local-z Vuz = 92.45 kN.

===============================================================================
[[[*]]] ANALYZE CAPACITY OF BIAXIALLY LOADED RC_COLUMN(RC-BRACE).
===============================================================================

( ). Compute design parameters.

-. Ag = 0.3025 m^2.
-. Ast = 0.0081 m^2.
-. Rhot = Ast/Ag = 0.026862
-. esu = fy/Es = 0.001379
-. beta1 = 0.8500 ( fc < 28 MPa.)

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/02/2025 14:49
http://www.MidasUser.com
Gen 2021 - 5 / 12 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

( ). Check the ratio of reinforcement.

-. Rhomin = 0.010000
-. Rhomax = 0.030000
-. Rhot = 0.026862
Rhomin < Rhot < Rhomax ---> O.K !

( ). Compute eccentricities of biaxially loaded column.

-. Ecny = ABS(Mcz/Pu) = 4.9822 m.
-. Ecnz = ABS(Mcy/Pu) = 2.0955 m.
-. Eccn = ABS(Mc/Pu) = 5.4049 m.
-. Rota = ATAN(Ecny/Ecnz) = 67.1879 deg.
-. Rotation of neutral axis = 67.1879 deg.

( ). Compute concentric axial load capacity.

-. Po = (0.85*fc)*(Ag-Ast) + fy*Ast = 7416.57 kN.
-. Maximum Axial Load : Pomax = 0.8*Po = 5933.26 kN.
-. Maximum Axial Tension : Pt = -fy*Ast = -2240.99 kN.

----------------------------------------------------------------------------
*. Analysis of balanced condition.
----------------------------------------------------------------------------

( ). Compute capacity of concrete stress block.

-. cb = (0.003/(0.003+esu))*d = 0.436 m.
-. ab = beta1*cb = 0.371 m.
-. Acom = 0.158 m^2.
-. DCcy = 0.124 m.
-. DCcz = 0.037 m.
-. Cc = 0.85*fc*Acom = 2773.30 kN.
-. MnCy = Cc*DCcz = 102.53 kN-m.
-. MnCz = Cc*DCcy = 343.41 kN-m.

( ). Compute capacity of reinforcement.

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/02/2025 14:49
http://www.MidasUser.com
Gen 2021 - 6 / 12 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

------------------------------------------------------------------------------------------------
-.Where,
di = Distance from the section's neutral axis to the i-th reinforcement ( m.)
esi = Strain in the i-th reinforcement
fsi = Stress in the i-th reinforcement ( KPa.)
Asi = Cross-section area of the i-th reinforcement ( m^2.)
Fsi = Tensile strength of the i-th reinforcement ( kN.)
dzi = Distance from the center of the section to the i-th reinforcement in the element local z-ax
is ( m.)
dyi = Distance from the center of the section to the i-th reinforcement in the element local y-ax
is ( m.)
M_nPyi = Flexural strength about the element local y-axes in the i-th reinforcement ( kN-m.)
M_nPzi = Flexural strength about the element local z-axes in the i-th reinforcement ( kN-m.)
---------------------------------------------------------------------------------------------------
-----------
-. Ps = SUM [ Fsi ] = 525.55 kN.
-. MnPy = SUM [ MnPyi ] = 90.42 kN-m.
-. MnPz = SUM [ MnPzi ] = 294.62 kN-m.

( ). Compute nominal capacity(Pb,Mb) of Balanced Condition.

-. Pb = Cc + Ps = 3298.85 kN.
-. Mny = MnCy + MnPy = 192.95 kN-m.
-. Mnz = MnCz + MnPz = 638.03 kN-m.
-. Mb = SQRT(Mny^2+Mnz^2) = 666.56 kN-m.

( ). Compare actual eccentricity with balanced eccentricity.

-. Balanced eccentricity : eb = Mb/Pb = 0.202 m.
-. Minimum eccentricity : Emin (not defined) = 0.000 m.
-. Actual eccentricity : Eccn = Mu/Pu = 5.405 m.
-. eb < Eccn ---> Tension controls.

----------------------------------------------------------------------------
*. Final analysis with searched neutral axis.
----------------------------------------------------------------------------

( ). Search for neutral axis...... Unit : kN., m.

-. P-M calculation method : Keep M/P constant
-------------------------------------------------------------------------------
Trial c Pn Mn Ecn Eccn Ratio
-------------------------------------------------------------------------------
1-st 0.220 2.41 492.72 204.081 5.405 2.65
2-nd 0.231 157.31 517.55 3.290 5.405 35.71
3-rd 0.226 80.68 505.36 6.264 5.405 86.28
4-th 0.229 119.57 511.60 4.279 5.405 73.68
5-th 0.227 100.14 508.49 5.078 5.405 93.56
6-th 0.227 90.41 506.93 5.607 5.405 96.40
7-th 0.227 95.28 507.71 5.329 5.405 98.57
-------------------------------------------------------------------------------

( ). Compute capacity of compression stress block.

-. a = beta1*c = 0.193 m.
-. Acom = 0.052 m^2.
-. DCcy = 0.205 m.
-. DCcz = 0.109 m.
-. Cc = 0.85*fc*Acom = 914.47 kN.
-. MnCy = Cc*DCcz = 99.89 kN-m.
-. MnCz = Cc*DCcy = 187.72 kN-m.

( ). Compute capacity of reinforcement.

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/02/2025 14:49
http://www.MidasUser.com
Gen 2021 - 7 / 12 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

3 0.555 -0.004341 -275790.38 4.909e-04 -135.38 0.000 -0.00 -0.211 28.63

4 0.514 -0.003799 -275790.38 4.909e-04 -135.38 0.106 -14.32 -0.211 28.63

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/02/2025 14:49
http://www.MidasUser.com
Gen 2021 - 8 / 12 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

5 0.473 -0.003256 -275790.38 8.042e-04 -221.80 0.211 -46.91 -0.211 46.91

6 0.343 -0.001537 -275790.38 4.909e-04 -135.38 0.211 -28.63 -0.070 9.54
7 0.213 0.000181 36279.86 4.909e-04 17.81 0.211 3.77 0.070 1.26
8 0.083 0.001900 275790.38 8.042e-04 221.80 0.211 46.91 0.211 46.91
9 0.124 0.001358 271610.72 4.909e-04 133.33 0.106 14.10 0.211 28.20
10 0.165 0.000816 163163.31 4.909e-04 80.09 0.000 0.00 0.211 16.94
11 0.206 0.000274 54715.89 4.909e-04 26.86 -0.106 -2.84 0.211 5.68
12 0.247 -0.000269 -53731.53 8.042e-04 -43.21 -0.211 9.14 0.211 -9.14
13 0.377 -0.001988 -275790.38 4.909e-04 -135.38 -0.211 28.63 0.070 -9.54
14 0.507 -0.003706 -275790.38 4.909e-04 -135.38 -0.211 28.63 -0.070 9.54
------------------------------------------------------------------------------------------------
-.Where,
di = Distance from the section's neutral axis to the i-th reinforcement ( m.)
esi = Strain in the i-th reinforcement
fsi = Stress in the i-th reinforcement ( KPa.)
Asi = Cross-section area of the i-th reinforcement ( m^2.)
Fsi = Tensile strength of the i-th reinforcement ( kN.)
dzi = Distance from the center of the section to the i-th reinforcement in the element local z-ax
is ( m.)
dyi = Distance from the center of the section to the i-th reinforcement in the element local y-ax
is ( m.)
M_nPyi = Flexural strength about the element local y-axes in the i-th reinforcement ( kN-m.)
M_nPzi = Flexural strength about the element local z-axes in the i-th reinforcement ( kN-m.)
---------------------------------------------------------------------------------------------------
-----------
-. Ps = SUM [ Fsi ] = -819.20 kN.
-. MnPy = SUM [ MnPyi ] = 99.71 kN-m.
-. MnPz = SUM [ MnPzi ] = 279.11 kN-m.

( ). Compute nominal capacity(Pn,Mn) of given neutral axis.

-. Pn = Cc + Ps = 95.28 kN.
-. Mny = MnCy + MnPy = 199.60 kN-m.
-. Mnz = MnCz + MnPz = 466.83 kN-m.
-. Mn = SQRT(Mny^2+Mnz^2) = 507.71 kN-m.

( ). Compute strength reduction factor.

-. et = 0.00543
-. et_min = 0.00138
-. et_max = 0.00500
-. et > et_max ---> phi =0.900

( ). Compute axial load and moment capacities(phiPn,phiMn).

-. phiPn = phi*Pn = 85.75 kN.
-. phiMn = phi*Mn = 456.94 kN-m.
-. phiMny = phi*Mny = 179.64 kN-m.
-. phiMnz = phi*Mnz = 420.15 kN-m.

( ). Check ratios of axial load and moment capacity.

-. Rat_P = Pu/phiPn = 0.968 < 1.000 ---> O.K.
-. Rat_M = Mc/phiMn = 0.982 < 1.000 ---> O.K.

===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY OF BIAXIALLY LOADED RC-COLUMN ( END ).
===============================================================================

( ). Compute maximum spacing of ties.

-. smax = MIN[ 16*Dbar, 48*Dstir, Hc, Bc ] = 0.400 m.

( ). Compute concrete shear strength in local-z direction.

( LCB = 5, POS = I )
-. Applied axial force : Pu = -281.72 kN.
-. Applied shear force : Vuz = 92.45 kN.
-. d = Hc-do = 0.486 m.
-. Bw = Bc = 0.550 m.

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/02/2025 14:49
http://www.MidasUser.com
Gen 2021 - 9 / 12 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/02/2025 14:49
http://www.MidasUser.com
Gen 2021 - 10 / 12 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

-. Acv = Bw*d = 0.268 m^2.

-. Vc = 1/6*(1+0.29*Pu/Ag)*SQRT(fc)*Acv = 148.04 kN.
-. phi = 0.75
-. phiVc = phi*Vc = 111.03 kN.
-. Vuz < phiVc ---> Minimum shear reinforcement is required.

( ). Compute required reinforcement in local-z direction shear.

-. Avz = MAX[0.062*SQRT(fc)*Bw/fys, 0.35*Bw/fys] = 6.980e-04 m^2/m.
-. Calc. spacing s1 = N_leg*Av1 / Avz = 0.225 m.
-. sz = MIN[ s1, d/2, 600 mm, smax ] = 0.225 m.

( ). Compute concrete shear strength in local-y direction.

( LCB = 10, POS = I )
-. Applied axial force : Pu = 141.66 kN.
-. Applied shear force : Vuy = 123.95 kN.
-. d = Bc-do = 0.486 m.
-. Bw = Hc = 0.550 m.
-. Acv = Bw*d = 0.268 m^2.
-. Vc = 1/6*(1+Pu/(14*Ag))*SQRT(fc)*Acv = 209.61 kN.
-. phi = 0.75
-. phiVc = phi*Vc = 157.20 kN.
-. Vuy < phiVc ---> Minimum shear reinforcement is required.

( ). Compute required reinforcement in local-y direction shear.

-. Avy = MAX[0.062*SQRT(fc)*Bw/fys, 0.35*Bw/fys] = 6.980e-04 m^2/m.
-. Calc. spacing s1 = N_leg*Av1 / Avy = 0.225 m.
-. sy = MIN[ s1, d/2, 600 mm, smax ] = 0.225 m.

===============================================================================
[[[*]]] ANALYZE SHEAR CAPACITY OF BIAXIALLY LOADED RC-COLUMN ( MIDDLE ).
===============================================================================

( ). Compute maximum spacing of ties.

-. smax = MIN[ 16*Dbar, 48*Dstir, Hc, Bc ] = 0.400 m.

( ). Compute concrete shear strength in local-z direction.

( LCB = 5, POS = 1/2 )
-. Applied axial force : Pu = -271.03 kN.
-. Applied shear force : Vuz = 92.45 kN.
-. d = Hc-do = 0.486 m.
-. Bw = Bc = 0.550 m.
-. Acv = Bw*d = 0.268 m^2.
-. Vc = 1/6*(1+0.29*Pu/Ag)*SQRT(fc)*Acv = 150.12 kN.
-. phi = 0.75
-. phiVc = phi*Vc = 112.59 kN.

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/02/2025 14:49
http://www.MidasUser.com
Gen 2021 - 11 / 12 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

-. Vuz < phiVc ---> Minimum shear reinforcement is required.

( ). Compute required reinforcement in local-z direction shear.

-. Avz = MAX[0.062*SQRT(fc)*Bw/fys, 0.35*Bw/fys] = 6.980e-04 m^2/m.
-. Calc. spacing s1 = N_leg*Av1 / Avz = 0.225 m.
-. sz = MIN[ s1, d/2, 600 mm, smax ] = 0.225 m.

( ). Compute concrete shear strength in local-y direction.

( LCB = 10, POS = 1/2 )
-. Applied axial force : Pu = 152.35 kN.
-. Applied shear force : Vuy = 123.95 kN.
-. d = Bc-do = 0.486 m.
-. Bw = Hc = 0.550 m.
-. Acv = Bw*d = 0.268 m^2.
-. Vc = 1/6*(1+Pu/(14*Ag))*SQRT(fc)*Acv = 210.12 kN.
-. phi = 0.75
-. phiVc = phi*Vc = 157.59 kN.
-. Vuy < phiVc ---> Minimum shear reinforcement is required.

( ). Compute required reinforcement in local-y direction shear.

-. Avy = MAX[0.062*SQRT(fc)*Bw/fys, 0.35*Bw/fys] = 6.980e-04 m^2/m.
-. Calc. spacing s1 = N_leg*Av1 / Avy = 0.225 m.
-. sy = MIN[ s1, d/2, 600 mm, smax ] = 0.225 m.

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/02/2025 14:49
http://www.MidasUser.com
Gen 2021 - 12 / 12 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

+============================================================+
| MIDAS(Modeling, Integrated Design & Analysis Software) |
| midas Gen - Design & checking system for windows |
+============================================================+
| RC-Member(Beam/Column/Brace/Wall) Analysis and Design |
| Based On Eurocode2:04, Eurocode2, ACI318-14, |
| ACI318M-14, ACI318-11, ACI318-08, ACI318-05, |
| ACI318-02, ACI318-99, ACI318-95, ACI318-89, |
| NSR-10, CSA-A23.3-94, BS8110-97, NSCP 2015 |
| |
| |
| |
| |
| (c)SINCE 1989 |
+============================================================+
| MIDAS Information Technology Co.,Ltd. (MIDAS IT) |
| MIDAS IT Design Development Team |
+============================================================+
| HomePage : www.MidasUser.com |
+============================================================+
| Gen 2021 |
+============================================================+

*. DEFINITION OF LOAD COMBINATIONS WITH SCALING UP FACTORS.

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/01/2025 17:49
http://www.MidasUser.com
Gen 2021 - 1 / 10 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

25 1 DL( 0.900) + RS-M(RS)(-1.000)

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/01/2025 17:49
http://www.MidasUser.com
Gen 2021 - 2 / 10 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

*.midas Gen - RC-COLUMN Analysis/Design Program.

*.DESCRIPTION OF COLUMN DATA (iSEC = 8) : 80x85

Section Type : Rectangular with Ties (RT)
Section Height (HTc) = 3.500 m.
Section Depth (Hc) = 0.850 m.
Section Width (Bc) = 0.800 m.
Concrete Cover to C.O.R. (do) = 0.076 m.
Concrete Strength (fc) = 20684.278 KPa.
Modulus of Elasticity (Ec) = 21375586.730 KPa.
Main Rebar Strength (fy) = 275790.378 KPa.
Ties/Spirals Strength (fys) = 275790.378 KPa.
Modulus of Elasticity (Es) = 200000000.000 KPa.

*.REBAR PATTERN = RT - 12 - 4 - P32 Unit : m.

--------------------------------------------------------
i dyi dzi Rebar Asi
--------------------------------------------------------
1 -0.324 -0.349 1-P32 0.00080
2 -0.324 -0.116 1-P32 0.00080
3 -0.324 0.116 1-P32 0.00080
4 -0.324 0.349 1-P32 0.00080
5 -0.108 0.349 1-P32 0.00080
6 0.108 0.349 1-P32 0.00080
7 0.324 0.349 1-P32 0.00080
8 0.324 0.116 1-P32 0.00080
9 0.324 -0.116 1-P32 0.00080
10 0.324 -0.349 1-P32 0.00080
11 0.108 -0.349 1-P32 0.00080
12 -0.108 -0.349 1-P32 0.00080
--------------------------------------------------------

( ). Factored forces/moments caused by unit load case. Unit : kN., m.

*.Load combination ID = 19
-------------------------------------------------------------------------------
Load Case Pu Myi Myj Mzi Mzj
-------------------------------------------------------------------------------
DL 683.14 -102.22 14.71 76.94 -22.54
LL -0.00 0.00 0.00 0.00 0.00
DL+LL 683.14 -102.22 14.71 76.94 -22.54
Others -259.40 161.77 389.25 13.16 -89.87
-------------------------------------------------------------------------------
DL+LL+Others 423.74 59.55 403.96 90.10 -112.41
-------------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/01/2025 17:49
http://www.MidasUser.com
Gen 2021 - 3 / 10 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

( ). Compute member end moments(M1,M2). Unit : kN-m.

-. For Dead Load(DL).
My1D = 14.71, My2D = 102.22
Mz1D = 22.54, Mz2D = 76.94
-. For Gravity Load(DL+LL).
My1G = 14.71, My2G = 102.22
Mz1G = 22.54, Mz2G = 76.94
-. For Total Load(DL+LL+WL(EL)).
My1 = 59.55, My2 = 403.96
Mz1 = 90.10, Mz2 = 112.41

( ). Check slenderness ratios of BRACED/UNBRACED frame.

-. Slenderness ratio limits.
SRy(Braced) = 34 - 12*| My1/My2 | = 32.231 (Single curvature)
SRz(Braced) = 34 + 12*MIN(|Mz1/Mz2|,0.5) = 40.000 (Reverse curvature)
-. Radii of gyration.
ry = 0.30*Hc = 0.255 m.
rz = 0.30*Bc = 0.240 m.
-. Unbraced lengths.
Ly = 3.500 m.
Lz = 3.500 m.
-. Effective length factors.
Ky = 1.000
Kz = 1.000
-. SLENy = Ky*Ly/ry = 13.725 <= SRy ---> NOT SLENDER.
-. SLENz = Kz*Lz/rz = 14.583 <= SRz ---> NOT SLENDER.

( ). Moment magnification factors for major axis(DBy,DSy).

-. DBy = 1.00 (Default value)
-. DSy = 1.00 (Default value)

( ). Moment magnification factors for minor axis(DBz,DSz).

-. DBz = 1.00 (Default value)
-. DSz = 1.00 (Default value)

( ). Compute minimum moments(Mmin).

-. emin_y = 15 mm. + 0.03*Hc = 0.041 m.
-. emin_z = 15 mm. + 0.03*Bc = 0.039 m.
-. Mmin_y = Pu * emin_y = 17.16 kN-m.
-. Mmin_z = Pu * emin_z = 16.53 kN-m.

( ). Compute magnified moments. (Pos : J, Local-y : Braced, Local-z : Braced).

-. No sidesway moments.
QMb_y = My_G = 14.71 kN-m.
QMb_z = Mz_G = -22.54 kN-m.
-. Sidesway moments.
QMs_y = My_S = 389.25 kN-m.
QMs_z = Mz_S = -89.87 kN-m.
-. Compute magnified moments(Mcy,Mcz).
Mcy(No-Slender) = DBy*(QMb_y + QMs_y) = 403.96 kN-m.
Mcz(No-Slender) = DBz*(QMb_z + QMs_z) = -112.41 kN-m.

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/01/2025 17:49
http://www.MidasUser.com
Gen 2021 - 4 / 10 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

( ). Check total moment including 2nd-order effects.

-. Moments due to 1st-order effects.
Mcy-1st = 403.96 kN-m.
Mcz-1st = 112.41 kN-m.
-. Moments due to 2nd-order effects.
Mcy-2nd = DBy*(QMb_y + QMs_y) = 403.96 kN-m.
Mcz-2nd = DBz*(QMb_z + QMs_z) = 112.41 kN-m.
-. Ratio of moment due to 2nd-order effects to moment due to 1st-order effects.
Mcy-2nd / Mcy-1st = 1.0000 <= 1.4 ---> O.K ! Apply magnified moment.
Mcz-2nd / Mcz-1st = 1.0000 <= 1.4 ---> O.K ! Apply magnified moment.

( ). Design forces/moments of column(brace).

-. Axial Force (Compression) Pu = 423.74 kN.
-. Combined Bending Moment Mc = 419.31 kN-m.
-. Bending Moment about Local-y Mcy = 403.96 kN-m.
-. Bending Moment about Local-z Mcz = -112.41 kN-m.
-. Shear Force of Local-y Vuy = 79.88 kN.
-. Shear Force of Local-z Vuz = 132.39 kN.

( ). Compute design parameters.

-. Ag = 0.6800 m^2.
-. Ast = 0.0097 m^2.
-. Rhot = Ast/Ag = 0.014193
-. esu = fy/Es = 0.001379
-. beta1 = 0.8500 ( fc < 28 MPa.)

( ). Check the ratio of reinforcement.

-. Rhomin = 0.010000
-. Rhomax = 0.030000
-. Rhot = 0.014193
Rhomin < Rhot < Rhomax ---> O.K !

( ). Compute eccentricities of biaxially loaded column.

-. Ecny = ABS(Mcz/Pu) = 0.2653 m.
-. Ecnz = ABS(Mcy/Pu) = 0.9533 m.
-. Eccn = ABS(Mc/Pu) = 0.9896 m.
-. Rota = ATAN(Ecny/Ecnz) = 15.5498 deg.
-. Rotation of neutral axis = 16.7131 deg.

( ). Compute concentric axial load capacity.

-. Po = (0.85*fc)*(Ag-Ast) + fy*Ast = 14447.49 kN.
-. Maximum Axial Load : Pomax = 0.8*Po = 11557.99 kN.
-. Maximum Axial Tension : Pt = -fy*Ast = -2661.65 kN.

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/01/2025 17:49
http://www.MidasUser.com
Gen 2021 - 5 / 10 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

----------------------------------------------------------------------------
*. Analysis of balanced condition.
----------------------------------------------------------------------------

( ). Compute capacity of concrete stress block.

-. cb = (0.003/(0.003+esu))*d = 0.650 m.
-. ab = beta1*cb = 0.553 m.
-. Acom = 0.366 m^2.
-. DCcy = 0.035 m.
-. DCcz = 0.191 m.
-. Cc = 0.85*fc*Acom = 6428.70 kN.
-. MnCy = Cc*DCcz = 1229.23 kN-m.
-. MnCz = Cc*DCcy = 225.24 kN-m.

( ). Compute capacity of reinforcement.

------------------------------------------------------------------------------------------------
i dsi esi fsi Asi Fsi dzi MnPyi dyi MnPzi
------------------------------------------------------------------------------------------------
1 0.949 -0.001379 -275790.38 8.042e-04 -221.80 -0.349 77.37 -0.324 71.82
2 0.727 -0.000352 -70317.49 8.042e-04 -56.55 -0.116 6.58 -0.324 18.31
3 0.504 0.000676 135155.40 8.042e-04 108.70 0.116 12.64 -0.324 -35.20
4 0.281 0.001703 275790.38 8.042e-04 221.80 0.349 77.37 -0.324 -71.82
5 0.219 0.001990 275790.38 8.042e-04 221.80 0.349 77.37 -0.108 -23.94
6 0.157 0.002276 275790.38 8.042e-04 221.80 0.349 77.37 0.108 23.94
7 0.095 0.002562 275790.38 8.042e-04 221.80 0.349 77.37 0.324 71.82
8 0.318 0.001535 275790.38 8.042e-04 221.80 0.116 25.79 0.324 71.82
9 0.540 0.000508 101504.34 8.042e-04 81.63 -0.116 -9.49 0.324 26.43
10 0.763 -0.000520 -103968.55 8.042e-04 -83.62 -0.349 29.17 0.324 -27.08
11 0.825 -0.000806 -161242.49 8.042e-04 -129.68 -0.349 45.23 0.108 -14.00
12 0.887 -0.001093 -218516.44 8.042e-04 -175.74 -0.349 61.30 -0.108 18.97
------------------------------------------------------------------------------------------------
-.Where,
di = Distance from the section's neutral axis to the i-th reinforcement ( m.)
esi = Strain in the i-th reinforcement
fsi = Stress in the i-th reinforcement ( KPa.)
Asi = Cross-section area of the i-th reinforcement ( m^2.)
Fsi = Tensile strength of the i-th reinforcement ( kN.)
dzi = Distance from the center of the section to the i-th reinforcement in the element local z-ax
is ( m.)
dyi = Distance from the center of the section to the i-th reinforcement in the element local y-ax
is ( m.)
M_nPyi = Flexural strength about the element local y-axes in the i-th reinforcement ( kN-m.)
M_nPzi = Flexural strength about the element local z-axes in the i-th reinforcement ( kN-m.)
---------------------------------------------------------------------------------------------------
-----------
-. Ps = SUM [ Fsi ] = 631.96 kN.
-. MnPy = SUM [ MnPyi ] = 558.03 kN-m.
-. MnPz = SUM [ MnPzi ] = 131.09 kN-m.

( ). Compute nominal capacity(Pb,Mb) of Balanced Condition.

-. Pb = Cc + Ps = 7060.66 kN.
-. Mny = MnCy + MnPy = 1787.26 kN-m.
-. Mnz = MnCz + MnPz = 356.33 kN-m.
-. Mb = SQRT(Mny^2+Mnz^2) = 1822.44 kN-m.

( ). Compare actual eccentricity with balanced eccentricity.

-. Balanced eccentricity : eb = Mb/Pb = 0.258 m.
-. Minimum eccentricity : Emin (not defined) = 0.000 m.
-. Actual eccentricity : Eccn = Mu/Pu = 0.990 m.
-. eb < Eccn ---> Tension controls.

----------------------------------------------------------------------------
*. Final analysis with searched neutral axis.

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/01/2025 17:49
http://www.MidasUser.com
Gen 2021 - 6 / 10 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

----------------------------------------------------------------------------

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/01/2025 17:49
http://www.MidasUser.com
Gen 2021 - 7 / 10 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

( ). Search for neutral axis...... Unit : kN., m.

-. P-M calculation method : Keep M/P constant
-------------------------------------------------------------------------------
Trial c Pn Mn Ecn Eccn Ratio
-------------------------------------------------------------------------------
1-st 0.328 1548.06 1402.82 0.906 0.990 90.80
2-nd 0.312 1285.77 1337.19 1.040 0.990 95.15
3-rd 0.320 1417.69 1370.51 0.967 0.990 97.64
4-th 0.316 1351.93 1353.97 1.002 0.990 98.81
-------------------------------------------------------------------------------

( ). Compute capacity of compression stress block.

-. a = beta1*c = 0.269 m.
-. Acom = 0.129 m^2.
-. DCcy = 0.100 m.
-. DCcz = 0.330 m.
-. Cc = 0.85*fc*Acom = 2260.46 kN.
-. MnCy = Cc*DCcz = 745.24 kN-m.
-. MnCz = Cc*DCcy = 225.24 kN-m.

( ). Compute capacity of reinforcement.

------------------------------------------------------------------------------------------------
i dsi esi fsi Asi Fsi dzi MnPyi dyi MnPzi
------------------------------------------------------------------------------------------------
1 0.949 -0.006000 -275790.38 8.042e-04 -221.80 -0.349 77.37 -0.324 71.82
2 0.727 -0.003889 -275790.38 8.042e-04 -221.80 -0.116 25.79 -0.324 71.82
3 0.504 -0.001777 -275790.38 8.042e-04 -221.80 0.116 -25.79 -0.324 71.82
4 0.281 0.000335 66910.99 8.042e-04 53.81 0.349 18.77 -0.324 -17.42
5 0.219 0.000923 184626.64 8.042e-04 148.49 0.349 51.79 -0.108 -16.03
6 0.157 0.001512 275790.38 8.042e-04 221.80 0.349 77.37 0.108 23.94
7 0.095 0.002100 275790.38 8.042e-04 221.80 0.349 77.37 0.324 71.82
8 0.318 -0.000011 -2252.35 8.042e-04 -1.81 0.116 -0.21 0.324 -0.59
9 0.540 -0.002123 -275790.38 8.042e-04 -221.80 -0.116 25.79 0.324 -71.82
10 0.763 -0.004234 -275790.38 8.042e-04 -221.80 -0.349 77.37 0.324 -71.82
11 0.825 -0.004823 -275790.38 8.042e-04 -221.80 -0.349 77.37 0.108 -23.94
12 0.887 -0.005412 -275790.38 8.042e-04 -221.80 -0.349 77.37 -0.108 23.94
------------------------------------------------------------------------------------------------
-.Where,
di = Distance from the section's neutral axis to the i-th reinforcement ( m.)
esi = Strain in the i-th reinforcement
fsi = Stress in the i-th reinforcement ( KPa.)
Asi = Cross-section area of the i-th reinforcement ( m^2.)
Fsi = Tensile strength of the i-th reinforcement ( kN.)
dzi = Distance from the center of the section to the i-th reinforcement in the element local z-ax
is ( m.)
dyi = Distance from the center of the section to the i-th reinforcement in the element local y-ax
is ( m.)
M_nPyi = Flexural strength about the element local y-axes in the i-th reinforcement ( kN-m.)
M_nPzi = Flexural strength about the element local z-axes in the i-th reinforcement ( kN-m.)
---------------------------------------------------------------------------------------------------
-----------
-. Ps = SUM [ Fsi ] = -908.53 kN.
-. MnPy = SUM [ MnPyi ] = 560.33 kN-m.
-. MnPz = SUM [ MnPzi ] = 133.54 kN-m.

( ). Compute nominal capacity(Pn,Mn) of given neutral axis.

-. Pn = Cc + Ps = 1351.93 kN.
-. Mny = MnCy + MnPy = 1305.57 kN-m.
-. Mnz = MnCz + MnPz = 358.79 kN-m.
-. Mn = SQRT(Mny^2+Mnz^2) = 1353.97 kN-m.

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/01/2025 17:49
http://www.MidasUser.com
Gen 2021 - 8 / 10 -
midas Gen RC Column Checking Result

PROJECT TITLE :
Company Integritus Consultancy Client
Author asus File Name Eastgrove China-roof-07-01-25.rcs

( ). Compute strength reduction factor.

-. et = 0.00600
-. et_min = 0.00138
-. et_max = 0.00500
-. et > et_max ---> phi =0.900

( ). Compute axial load and moment capacities(phiPn,phiMn).

-. phiPn = phi*Pn = 1216.74 kN.
-. phiMn = phi*Mn = 1218.58 kN-m.
-. phiMny = phi*Mny = 1175.01 kN-m.
-. phiMnz = phi*Mnz = 322.91 kN-m.

( ). Check ratios of axial load and moment capacity.

-. Rat_P = Pu/phiPn = 0.348 < 1.000 ---> O.K.
-. Rat_M = Mc/phiMn = 0.344 < 1.000 ---> O.K.

( ). Compute maximum spacing of ties.

-. smax = MIN[ 16*Dbar, 48*Dstir, Hc, Bc ] = 0.480 m.

( ). Compute concrete shear strength in local-z direction.

( LCB = 7, POS = I )
-. Applied axial force : Pu = 936.07 kN.
-. Applied shear force : Vuz = 132.39 kN.
-. d = Hc-do = 0.774 m.
-. Bw = Bc = 0.800 m.
-. Acv = Bw*d = 0.619 m^2.
-. Vc = 1/6*(1+Pu/(14*Ag))*SQRT(fc)*Acv = 515.37 kN.
-. phi = 0.75
-. phiVc = phi*Vc = 386.53 kN.
-. Vuz < phiVc/2 ---> Shear reinforcement is not required.

( ). Compute concrete shear strength in local-y direction.

( LCB = 7, POS = I )
-. Applied axial force : Pu = 936.07 kN.
-. Applied shear force : Vuy = 79.88 kN.
-. d = Bc-do = 0.724 m.
-. Bw = Hc = 0.850 m.
-. Acv = Bw*d = 0.615 m^2.
-. Vc = 1/6*(1+Pu/(14*Ag))*SQRT(fc)*Acv = 512.20 kN.
-. phi = 0.75
-. phiVc = phi*Vc = 384.15 kN.
-. Vuy < phiVc/2 ---> Shear reinforcement is not required.

Modeling, Integrated Design & Analysis Software Print Date/Time : 07/01/2025 17:49
http://www.MidasUser.com
Gen 2021 - 9 / 10 -
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

1. General Information
(1) Design Code : AISC-LRFD10M
(2) Code Unit : N, mm
[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material 0.550

(1) Base Plate : A36 (Fy = 248,211KPa, Es = 199,948,024KPa) 0.350

(2) Rib / Wing : A36

(3) Anchor Bolt : A325 0.0100
(4) Concrete : 27,579KPa

0.350
0.550
3. Section
(1) Column : HW 350x350x12/19

0.0500
(2) Base Plate : 0.550x0.550x0.0320t (Rectangle)
(3) Anchor Bolt : 12-M27 (Pos.(x) : 0.0500m, Pos.(y) : 0.0500m)
(4) Rib Plate : 0.400x0.0120t (No(x) : 3EA, No(y) : 3EA) 0.0500

4. Design Forces
(1) Pu : 79.68kN
(2) Mux : 128kN·m
(3) Muy : 320kN·m
(4) Vux : 113kN

0.400
(5) Vuy : 59.00kN

0.0100
5. Check bearing stress of base plate
(1) Bearing Stress
0.0100
fmax = 26,789N (Area = 0.00000100m²)
fmin = 36.18N (Area = 0.00000100m²)
σmax = 26,789KPa
σmin = 36.18KPa
(2) Calculate Bearing Stress of Concrete
Φ = 0.650
A1 = 0.302m², A2 = 1.210m²
Fn = 0.85 fck A2 / A1 = 46,884KPa
øFn = 30,475KPa
(3) Calculate ratio
σmax / øFn = 0.879 < 1.000 → O.K

2025-07-03 10:50 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

26.79

3.35 7.37 11.39 15.40 19.42 23.44

0.00 5.36 9.38 13.39 17.41 21.43 26.79

6. Check tension stress of anchor bolt

2025-07-03 10:50 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

-110.69 -45.98

-133.51

-156.33

-179.15 -114.44 -49.74

-164.22 -134.36 -104.50 -74.64 -44.79 -14.93

-179.15 -149.29 -119.43 -89.57 -59.72 -29.86 0.00

(1) Tension Forces

Tu.max = -179kN
Tu.min = -45.98kN
(2) Check Tensile Strength
Φ = 0.750
Fnt = 620,528KPa
Ab = 0.000573m²
Rnt = Fnt x Ab = 355kN
øRnt = 266kN
(3) Calculate ratio
Tu.max / øRnt = 0.672 < 1.000 → O.K

7. Check base plate

(1) Moment Diagram ( Element Force. Nodal Average is not Applied. )
Moment Diagram (Mxx)

2025-07-03 10:50 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

-30.99kN·m/m

-8.21 -4.24 -0.28 3.68 7.64 11.60

-49.00 -6.23 -2.26 1.70 5.66 9.62 68.25

Moment Diagram (Myy)

2025-07-03 10:50 4
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

-55.29kN·m/m

-14.39 -8.70 -3.01 2.68 8.37 14.06

-75.70 -11.54 -5.85 -0.17 5.52 11.21 68.15

(2) Shear Force Diagram

Shear Force Diagram (Vxx)

2025-07-03 10:50 5
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

-384.87 -205.38 -25.88 153.62 333.12 512.62

-4021.25 -295.13 -115.63 63.87 243.37 422.87 5437.81

Shear Force Diagram (Vyy)

2025-07-03 10:50 6
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

-627.51 -366.07 -104.63 156.81 418.24 679.68

-3724.46 -496.79 -235.35 26.09 287.52 548.96 4484.17

(3) Design Moment (Use Average)

Mux = -30.99kN·m/m
Muy = -55.29kN·m/m
Mu = max( Mux , Muy ) = -55.29kN·m/m
(4) Calculate moment strength
Φ = 0.900
Zbp = (tbp )2 / 4 = 0.000256 m3 /m
Mn = Fy x Zbp = 63.54kN·m/m
øMn = 57.19kN·m/m
(5) Calculate ratio
Mu / øMn = 0.967 < 1.000 → O.K

8. Force Diagram ( Rib Plate )

(1) Force Diagram
Moment Diagram

2025-07-03 10:50 7
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

4.69 13.69 22.69 31.69 40.69 49.69

0.19 9.19 18.19 27.19 36.19 45.19 54.19

Shear Force Diagram

2025-07-03 10:50 8
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

29.32 83.73 138.14 192.55 246.96 301.37

2.12 56.53 110.93 165.34 219.75 274.16 328.57

9. Check rib plate ( Moment Strength )

(1) Design Forces
Mu = 54.19kN·m
(2) Calculate nominal flexural strength for Yielding (Y)
Mp = Fy Zx = 119kN·m
My = Fy Sx = 79.43kN·m
Mn1 = min(Mp , 1.6My ) = 119kN·m
(3) Calculate nominal flexural strength for Lateral-torsional buckling (LTB)
0.08 Es Lb d 1.9 Es
= 64.44 < 2 = 736 < = 1,531
Fy t Fy
Lb d
Mn = Cb ( 1.52 - 0.274 ( 2 ) Fy ) My = 101kN·m
t
Mn2 = min( Mn , Mp ) = 101kN·m
(4) Calculate flexural strength about major axis
Mnx = min(Mn1 , Mn2 ) = 101kN·m
Resistance factor for flexure : ø = 0.900
øMnx = 90.76kN·m
Mux / øMnx = 0.597 < 1.000 → O.K

10. Check rib plate ( Shear Strength )

(1) Design Forces
Vu = 329kN
(2) Calculate the web plate buckling coefficient (kv )
kv = 5.000 (for stiffened webs)
(3) Calculate the web shear coefficient (Cv )

2025-07-03 10:50 9
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP1

for webs of all other doubly/singly symmetric shapes and channels

h / tw = 0.000 < 1.10 kv Es / Fy = 69.81
Cv = 1.000
(4) Calculate shear strength in local-y direction
Aw = 0.00480m²
Vny = 0.6 Fy Aw Cv = 715kN
Resistance factor for shear : ø = 0.900
øVny = 643kN
Vuy / øVny = 0.511 < 1.000 → O.K

11. Check anchor bolt (Cast-In-Place)

(1) Design Force
Number of Anchor Bolt = 12EA
Tu.max = -179kN
Vu = 127kN
Vu1 = 10.62kN
(2) Check Shear Strength
Φ = 0.750
Ab = 0.000573m²
Fnv = 330,948KPa
Rnv = Fnv x Ab = 189kN
øRnv = 142kN
Vu1 / øRnv = 0.075 < 1.000 → O.K
(3) Check Tensile Strength
Φ = 0.750
Ab = 0.000573m²
Fnt = 620,528KPa
fv = Vu1 / Ab = 18,554KPa
Fnt
Fnt ' = 1.3Fnt - fv ≤ Fnt
øFnv
Fnt ' = 620,528KPa
Rnt = Fnt ' x Ab = 355kN
øRnt = 266kN
Tu.max / øRnt = 0.672 < 1.000 → O.K

12. Check Development Length of Anchor Bolt

(1) Check Development Length (Hooked Bar)
Φ = 0.750
Lanc = 0.756m
Tanc = ø Fanc Aanc = 266kN
Lh1 = ( Tanc / 2 ) / ( 0.70 fck danc ) = 0.256m
Lh2 = 17 danc = 0.459m
Lreq = Lh1 + Lh2 = 0.715m
Lreq / Lanc = 0.945 < 1.000 → O.K

2025-07-03 10:50 10
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

1. General Information
(1) Design Code : AISC-LRFD10M
(2) Code Unit : N, mm
[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material 0.800

(1) Base Plate : A36 (Fy = 248,211KPa, Es = 199,948,024KPa) 0.302

(2) Rib / Wing : A36

(3) Anchor Bolt : A325
(4) Concrete : 20,684KPa 0.0100
3. Section

0.850
0.594
(1) Column : HM 594x302x14/23
(2) Base Plate : 0.800x0.850x0.0320t (Rectangle)
(3) Anchor Bolt : 18-M27 (Pos.(x) : 0.0500m, Pos.(y) : 0.0500m)

0.0500
(4) Rib Plate : 0.300x0.0160t (No(x) : 0EA, No(y) : 3EA)

4. Design Forces
0.0500
(1) Pu : -89.00kN
(2) Mux : -94.00kN·m
(3) Muy : 391kN·m
(4) Vux : 123kN
(5) Vuy : 270kN

5. Check bearing stress of base plate

0.300
(1) Bearing Stress 0.0100
fmax = 9,196N (Area = 0.00000100m²)
fmin = 5.638N (Area = 0.00000100m²) 0.0100
σmax = 9,196KPa
σmin = 5.638KPa
(2) Calculate Bearing Stress of Concrete
Φ = 0.650
A1 = 0.680m², A2 = 2.720m²
Fn = 0.85 fck A2 / A1 = 35,163KPa
øFn = 22,856KPa
(3) Calculate ratio
σmax / øFn = 0.402 < 1.000 → O.K

2025-07-03 11:14 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

9.20

1.15 2.53 3.91 5.29 6.67 8.05

0.00 1.84 3.22 4.60 5.98 7.36 9.20

6. Check tension stress of anchor bolt

2025-07-03 11:14 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

-94.05 -67.46 -40.86 -14.27

-89.97

-85.89

-81.80

-77.72

-73.64 -47.05 -20.46

-86.21 -70.54 -54.86 -39.19 -23.51 -7.84

-94.05 -78.37 -62.70 -47.02 -31.35 -15.67 0.00

(1) Tension Forces

Tu.max = -94.05kN
Tu.min = -14.27kN
(2) Check Tensile Strength
Φ = 0.750
Fnt = 620,528KPa
Ab = 0.000573m²
Rnt = Fnt x Ab = 355kN
øRnt = 266kN
(3) Calculate ratio
Tu.max / øRnt = 0.353 < 1.000 → O.K

7. Check base plate

(1) Moment Diagram ( Element Force. Nodal Average is not Applied. )
Moment Diagram (Mxx)

2025-07-03 11:14 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

17.06kN·m/m

-8.26 -5.13 -1.99 1.14 4.27 7.41

-18.90 -6.69 -3.56 -0.43 2.71 5.84 30.61

Moment Diagram (Myy)

2025-07-03 11:14 4
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

-46.10kN·m/m

-24.05 -17.52 -11.00 -4.48 2.05 8.57

-59.09 -20.78 -14.26 -7.74 -1.21 5.31 31.11

(2) Shear Force Diagram

Shear Force Diagram (Vxx)

2025-07-03 11:14 5
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

-175.69 -96.93 -18.18 60.58 139.34 218.10

-1127.90 -136.31 -57.55 21.20 99.96 178.72 2182.22

Shear Force Diagram (Vyy)

2025-07-03 11:15 6
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

-453.34 -268.41 -83.49 101.43 286.35 471.28

-1783.63 -360.87 -175.95 8.97 193.89 378.81 2013.72

(3) Design Moment (Use Average)

Mux = 17.06kN·m/m
Muy = -46.10kN·m/m
Mu = max( Mux , Muy ) = -46.10kN·m/m
(4) Calculate moment strength
Φ = 0.900
Zbp = (tbp )2 / 4 = 0.000256 m3 /m
Mn = Fy x Zbp = 63.54kN·m/m
øMn = 57.19kN·m/m
(5) Calculate ratio
Mu / øMn = 0.806 < 1.000 → O.K

8. Force Diagram ( Rib Plate )

(1) Force Diagram
Moment Diagram

2025-07-03 11:15 7
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

10.84 20.56 30.28 40.00 49.72 59.44

5.98 15.70 25.42 35.14 44.86 54.58 64.30

Shear Force Diagram

2025-07-03 11:15 8
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

48.68 96.02 143.35 190.69 238.03 285.37

25.01 72.35 119.68 167.02 214.36 261.70 309.04

9. Check rib plate ( Moment Strength )

(1) Design Forces
Mu = 64.30kN·m
(2) Calculate nominal flexural strength for Yielding (Y)
Mp = Fy Zx = 89.36kN·m
My = Fy Sx = 59.57kN·m
Mn1 = min(Mp , 1.6My ) = 89.36kN·m
(3) Calculate nominal flexural strength for Lateral-torsional buckling (LTB)
0.08 Es Lb d 1.9 Es
= 64.44 < 2 = 457 < = 1,531
Fy t Fy
Lb d
Mn = Cb ( 1.52 - 0.274 ( 2 ) Fy ) My = 81.29kN·m
t
Mn2 = min( Mn , Mp ) = 81.29kN·m
(4) Calculate flexural strength about major axis
Mnx = min(Mn1 , Mn2 ) = 81.29kN·m
Resistance factor for flexure : ø = 0.900
øMnx = 73.16kN·m
Mux / øMnx = 0.879 < 1.000 → O.K

10. Check rib plate ( Shear Strength )

(1) Design Forces
Vu = 309kN
(2) Calculate the web plate buckling coefficient (kv )
kv = 5.000 (for stiffened webs)
(3) Calculate the web shear coefficient (Cv )

2025-07-03 11:15 9
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : BP2

for webs of all other doubly/singly symmetric shapes and channels

11. Check anchor bolt (Cast-In-Place)

(1) Design Force
Number of Anchor Bolt = 18EA
Tu.max = -94.05kN
Vu = 297kN
Vu1 = 16.48kN
(2) Check Shear Strength
Φ = 0.750
Ab = 0.000573m²
Fnv = 330,948KPa
Rnv = Fnv x Ab = 189kN
øRnv = 142kN
Vu1 / øRnv = 0.116 < 1.000 → O.K
(3) Check Tensile Strength
Φ = 0.750
Ab = 0.000573m²
Fnt = 620,528KPa
fv = Vu1 / Ab = 28,789KPa
Fnt
Fnt ' = 1.3Fnt - fv ≤ Fnt
øFnv
Fnt ' = 620,528KPa
Rnt = Fnt ' x Ab = 355kN
øRnt = 266kN
Tu.max / øRnt = 0.353 < 1.000 → O.K

12. Check Development Length of Anchor Bolt

(1) Check Development Length (Hooked Bar)
Φ = 0.750
Lanc = 0.810m
Tanc = ø Fanc Aanc = 266kN
Lh1 = ( Tanc / 2 ) / ( 0.70 fck danc ) = 0.341m
Lh2 = 17 danc = 0.459m
Lreq = Lh1 + Lh2 = 0.800m
Lreq / Lanc = 0.987 < 1.000 → O.K

2025-07-03 11:15 10
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1

1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ]
5.00
2. Material 2.50 2.50
(1) F'c : 20,684KPa
(2) Fy : 227,600KPa

3. Section

2.50
(1) Section Size
Depth : 0.400m
Cover : 0.0800m

5.00
(2) Column Section
Shape of Column : Rectangle Y1
Section : 0.550x0.550m
2.50
4. Rebar X1
(1) Direction Y
Layer 1 : #[email protected] (As = 0.000305m²)
Layer 2 : #[email protected] (As = 0.000305m²)
(2) Direction X
Layer 1 : #[email protected] (As = 0.000305m²)
Layer 2 : #[email protected] (As = 0.000305m²)
2.10

5. Foundation
(1) Foundation Size
0.40

Lx : 5.000m
Ly : 5.000m
fe : 80.34kN/m²

6. Design Load
(1) Service Load
Ps : 339kN
Msx : 330kN·m
Msy : 82.00kN·m
(2) Factored Load
Pu : 413kN
Mux : 464kN·m
Muy : 116kN·m
(3) Surcharge Load
Surface Load : 0.000kN/m²
Weight Density : 18.00kN/m³
Soil Height : 2.100m
(4) Self weight is considered.

7. Check Soil Capacity

(1) Calculate actual soil stress
qs,top-left = 72.38kN/m² qs,top-right = 80.25kN/m²
qs,bot-left = 40.70kN/m² qs,bot-right = 48.57kN/m²
qs,max = 80.25kN/m²
qs,max / fe = 0.999 → O.K
(2) Calculate factored soil stress
qu,top-left = 105kN/m² qu,top-right = 116kN/m²

2025-07-01 18:42 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1

qu,bot-left = 60.14kN/m² qu,bot-right = 71.23kN/m²

qu,max = 116kN/m² qu,min = 60.14kN/m²

8. Check Shear
(1) Calculate one-way shear
ø = 0.750
Vux = 79.52kN øVcx = 884kN
Vux / øVcx = 0.0900 → O.K
Vuy = 186kN øVcy = 839kN
Vuy / øVcy = 0.221 → O.K
(2) Calculate two-way shear
b0 Vc1 Vc2 Vc3 Vc Vu øVc
- Ratio
(m) (kN) (kN) (kN) (kN) (kN) (kN)
Interior 3.448 2,438 2,284 1,625 1,625 401 1,219 0.329
Edge(X) 6.724 4,755 2,688 3,170 2,688 244 2,016 0.121
Edge(Y) 6.724 4,755 2,688 3,170 2,688 244 2,016 0.121
Corner 5.862 4,145 2,117 2,763 2,117 0.000 1,588 0.000

INTERIOR EDGE( X ) EDGE( Y ) CORNER

ø = 0.750
d = 0.312m
4
Vc1 = ( 2 + ) f'c b0 d
β
as d
Vc2 = ( + 2 ) f'c b0 d
b0
Vc3 = 4 f'c b0 d
Vc = min(Vc1 , Vc2 , Vc3 )
Vu = 401kN
Vu / øVc = 0.329 → O.K

9. Check Moment Capacity

(1) Calculate moment capacity (Direction X)
ø = 0.900
Muy = 15.42kN·m øMny = 38.94kN·m
Muy / øMny = 0.396 → O.K
(2) Calculate moment capacity (Direction Y)
ø = 0.900
Mux = 24.30kN·m øMnx = 36.95kN·m
Mux / øMnx = 0.658 → O.K

10. Check Rebar

(1) Calculate minimum rebar area required
As,min = 0.00200D = 0.000244m²
2025-07-01 18:42 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1

(2) Calculate minimum rebar space required (Direction Y)

As = 0.000200m² (#[email protected])
sreq. = 0.250m
sx = 0.200m < sreq. = 0.250m → O.K
(3) Calculate minimum rebar space required (Direction X)
As = 0.000200m² (#[email protected])
sreq. = 0.250m
sy = 0.200m < sreq. = 0.250m → O.K

2025-07-01 18:42 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1-A

1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material
(1) F'c : 20,684KPa
(2) Fy : 227,600KPa

3. Design Load
(1) Column 1
Ps : 183kN
Pu : 214kN
(2) Column 2
Ps : 378kN
Pu : 511kN
(3) Surcharge Load
Surface Load : 0.000kN/m²
Weight Density : 18.00kN/m³
Soil Height : 2.000m
(4) Self weight is considered.

4. Foundation
(1) Foundation Size
Lx : 7.250m
Ly : 3.500m
Depth : 0.500m
Cover : 0.102m
(2) Soil Bearing Capacity
fe : 80.34kN/m²

5. Column
No. Shape Section Lxi
1 Rectangle 0.550x0.550m 2.100m
2 Rectangle 0.550x0.550m 3.050m

2025-07-04 21:59 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1-A

137.80

X
2025-07-04 21:59 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1-A

6. Rebar
(1) Direction X
Cantilever(L) : #[email protected] (As = 0.000305m²)
Colm (1) : #[email protected] (As = 0.000305m²)
Span (1-2) : #[email protected] (As = 0.000305m²)
Colm (2) : #[email protected] (As = 0.000305m²)
Cantilever(R) : #[email protected] (As = 0.000305m²)
(2) Direction Y
Colm (1) : #[email protected] (As = 0.000305m²)
Colm (2) : #[email protected] (As = 0.000865m²)

7. Check Soil Capacity

(1) Calculate actual soil stress
qs,left = 59.83kN/m² qs,right = 79.19kN/m²
qs,max = 79.19kN/m²
qs,max / fe = 0.986 → O.K
(2) Calculate factored soil stress
qu,left = 13.80kN/m² qu,right = 43.34kN/m²
qu,max = 43.34kN/m² qu,min = 13.80kN/m²

8. Check Shear
(1) Calculate one-way shear
ø = 0.750
Vux = 203kN øVcx = 774kN
Vux / øVcx = 0.262 → O.K
(2) Calculate two-way shear
b0 Vc1 Vc2 Vc3 Vc Vu øVc
Column Position Ratio
(m) (kN) (kN) (kN) (kN) (kN) (kN)
1 Interior 3.730 3,233 3,288 2,155 2,155 189 1,617 0.117
2 Interior 3.727 3,224 3,276 2,149 2,149 486 1,612 0.302

ø = 0.750
d = 0.000m
4
Vc1 = ( 2 + ) f'c b0 d
β
as d
Vc2 = ( + 2 ) f'c b0 d
b0
Vc3 = 4 f'c b0 d
Vc = min(Vc1 , Vc2 , Vc3 )
Vu = 486kN
Vu / øVc = 0.302 → O.K

9. Check Moment Capacity

(1) Calculate moment capacity (Direction X)
Position Top/Bottom ø Mu(kN·m/m) øMn(kN·m/m) Ratio Remark
Cantilever(L) Bottom 0.900 8.263 23.97 0.345 OK
Colm (1) Bottom 0.900 9.511 23.97 0.397 OK
Span (1-2) Top 0.900 0.000 23.97 0.000 OK
Colm (2) Bottom 0.900 22.25 23.97 0.928 OK
Cantilever(R) Bottom 0.900 20.74 23.97 0.865 OK

(2) Calculate moment capacity (Direction Y)

Position Top/Bottom ø Mu(kN·m/m) øMn(kN·m/m) Ratio Remark

2025-07-04 21:59 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1-A

Colm (1) Bottom 0.900 21.93 22.98 0.954 OK

Colm (2) Bottom 0.900 52.45 62.85 0.834 OK

10. Check Rebar

(1) Calculate minimum rebar area required
As,min = 0.00200D = 0.000305m²
(2) Calculate minimum rebar space required (Direction X)
Position Top/Bottom Rebar As(m²) Smax(m) Sreq(m) Remark
Cantilever(L) Bottom #[email protected] 0.000200 0.457 0.200 NG
Colm (1) Bottom #[email protected] 0.000200 0.457 0.200 NG
Span (1-2) Top #[email protected] 0.000200 0.457 0.200 NG
Colm (2) Bottom #[email protected] 0.000200 0.457 0.200 NG
Cantilever(R) Bottom #[email protected] 0.000200 0.457 0.200 NG

(3) Calculate minimum rebar space required (Direction Y)

Position Top/Bottom Rebar As(m²) Smax(m) Sreq(m) Remark
Colm (1) Bottom #[email protected] 0.000200 0.457 0.200 NG
Colm (2) Bottom #[email protected] 0.000284 0.457 0.284 OK

2025-07-04 21:59 4
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1-B

1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ]

2. Material
(1) F'c : 20,684KPa
(2) Fy : 227,600KPa

3. Design Load
(1) Column 1
Ps : 296kN
Pu : 368kN
(2) Column 2
Ps : 430kN
Pu : 515kN
(3) Surcharge Load
Surface Load : 0.000kN/m²
Weight Density : 18.00kN/m³
Soil Height : 2.000m
(4) Self weight is considered.

4. Foundation
(1) Foundation Size
Lx : 8.400m
Ly : 3.500m
Depth : 0.500m
Cover : 0.102m
(2) Soil Bearing Capacity
fe : 80.34kN/m²

5. Column
No. Shape Section Lxi
1 Rectangle 0.550x0.550m 2.300m
2 Rectangle 0.550x0.550m 3.800m

2025-07-04 21:56 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1-B

137.80

21.6

Y
X

2025-07-04 21:56 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1-B

6. Rebar
(1) Direction X
Cantilever(L) : #[email protected] (As = 0.000305m²)
Colm (1) : #[email protected] (As = 0.000305m²)
Span (1-2) : #[email protected] (As = 0.000305m²)
Colm (2) : #[email protected] (As = 0.000406m²)
Cantilever(R) : #[email protected] (As = 0.000406m²)
(2) Direction Y
Colm (1) : #[email protected] (As = 0.000577m²)
Colm (2) : #[email protected] (As = 0.000865m²)

7. Check Soil Capacity

(1) Calculate actual soil stress
qs,left = 65.88kN/m² qs,right = 78.27kN/m²
qs,max = 78.27kN/m²
qs,max / fe = 0.974 → O.K
(2) Calculate factored soil stress
qu,left = 23.27kN/m² qu,right = 36.84kN/m²
qu,max = 36.84kN/m² qu,min = 23.27kN/m²

8. Check Shear
(1) Calculate one-way shear
ø = 0.750
Vux = 203kN øVcx = 774kN
Vux / øVcx = 0.262 → O.K
(2) Calculate two-way shear
b0 Vc1 Vc2 Vc3 Vc Vu øVc
Column Position Ratio
(m) (kN) (kN) (kN) (kN) (kN) (kN)
1 Interior 3.727 3,224 3,276 2,149 2,149 342 1,612 0.212
2 Interior 3.727 3,224 3,276 2,149 2,149 489 1,612 0.304

ø = 0.750
d = 0.000m
4
Vc1 = ( 2 + ) f'c b0 d
β
as d
Vc2 = ( + 2 ) f'c b0 d
b0
Vc3 = 4 f'c b0 d
Vc = min(Vc1 , Vc2 , Vc3 )
Vu = 489kN
Vu / øVc = 0.304 → O.K

9. Check Moment Capacity

(1) Calculate moment capacity (Direction X)
Position Top/Bottom ø Mu(kN·m/m) øMn(kN·m/m) Ratio Remark
Cantilever(L) Bottom 0.900 15.23 23.97 0.635 OK
Colm (1) Bottom 0.900 16.10 23.97 0.671 OK
Span (1-2) Top 0.900 0.000 23.97 0.000 OK
Colm (2) Bottom 0.900 23.49 31.79 0.739 OK
Cantilever(R) Bottom 0.900 22.34 31.79 0.703 OK

(2) Calculate moment capacity (Direction Y)

Position Top/Bottom ø Mu(kN·m/m) øMn(kN·m/m) Ratio Remark

2025-07-04 21:56 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F1-B

Colm (1) Bottom 0.900 37.81 42.63 0.887 OK

Colm (2) Bottom 0.900 52.89 62.85 0.841 OK

10. Check Rebar

(1) Calculate minimum rebar area required
As,min = 0.00200D = 0.000305m²
(2) Calculate minimum rebar space required (Direction X)
Position Top/Bottom Rebar As(m²) Smax(m) Sreq(m) Remark
Cantilever(L) Bottom #[email protected] 0.000200 0.457 0.200 NG
Colm (1) Bottom #[email protected] 0.000200 0.457 0.200 NG
Span (1-2) Top #[email protected] 0.000200 0.457 0.200 NG
Colm (2) Bottom #[email protected] 0.000200 0.457 0.200 OK
Cantilever(R) Bottom #[email protected] 0.000200 0.457 0.200 OK

(3) Calculate minimum rebar space required (Direction Y)

Position Top/Bottom Rebar As(m²) Smax(m) Sreq(m) Remark
Colm (1) Bottom #[email protected] 0.000284 0.457 0.284 OK
Colm (2) Bottom #[email protected] 0.000284 0.457 0.284 OK

2025-07-04 21:56 4
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F2

1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ] 3.20
1.60 1.60
2. Material
(1) F'c : 20,684KPa
(2) Fy : 227,600KPa

1.60
3. Section
(1) Section Size

3.20
Depth : 0.600m
Cover : 0.0800m Y1
(2) Column Section

1.60
Shape of Column : Rectangle
X1
Section : 0.850x0.800m

4. Rebar
(1) Direction Y
Layer 1 : #[email protected] (As = 0.000406m²)
Layer 2 : #[email protected] (As = 0.000406m²)
(2) Direction X
2.60

Layer 1 : #[email protected] (As = 0.000406m²)

Layer 2 : #[email protected] (As = 0.000406m²)

5. Foundation
(1) Foundation Size
0.60

Lx : 3.200m
Ly : 3.200m
fe : 427kN/m²

6. Design Load
(1) Service Load
Ps : 2,506kN
Msx : 16.43kN·m
Msy : 424kN·m
(2) Factored Load
Pu : 2,801kN
Mux : 29.85kN·m
Muy : 577kN·m
(3) Surcharge Load
Surface Load : 0.000kN/m²
Weight Density : 18.00kN/m³
Soil Height : 2.600m
(4) Self weight is considered.

7. Check Soil Capacity

(1) Calculate actual soil stress
qs,top-left = 231kN/m² qs,top-right = 386kN/m²
qs,bot-left = 225kN/m² qs,bot-right = 380kN/m²
qs,max = 386kN/m²
qs,max / fe = 0.903 → O.K
(2) Calculate factored soil stress
qu,top-left = 265kN/m² qu,top-right = 476kN/m²

2025-07-01 18:19 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F2

qu,bot-left = 254kN/m² qu,bot-right = 465kN/m²

qu,max = 476kN/m² qu,min = 254kN/m²

8. Check Shear
(1) Calculate one-way shear
ø = 0.750
Vux = 609kN øVcx = 928kN
Vux / øVcx = 0.656 → O.K
Vuy = 481kN øVcy = 899kN
Vuy / øVcy = 0.534 → O.K
(2) Calculate two-way shear
b0 Vc1 Vc2 Vc3 Vc Vu øVc
- Ratio
(m) (kN) (kN) (kN) (kN) (kN) (kN)
Interior 5.348 5,962 6,029 4,137 4,137 2,312 3,103 0.745
Edge(X) 5.874 6,548 5,242 4,544 4,544 1,872 3,408 0.549
Edge(Y) 5.874 6,548 5,242 4,544 4,544 1,843 3,408 0.541
Corner 4.537 5,058 3,735 3,509 3,509 1,087 2,632 0.413

INTERIOR EDGE( X ) EDGE( Y ) CORNER

ø = 0.750
d = 0.512m
4
Vc1 = ( 2 + ) f'c b0 d
β
as d
Vc2 = ( + 2 ) f'c b0 d
b0
Vc3 = 4 f'c b0 d
Vc = min(Vc1 , Vc2 , Vc3 )
Vu = 2,312kN
Vu / øVc = 0.745 → O.K

9. Check Moment Capacity

(1) Calculate moment capacity (Direction X)
ø = 0.900
Muy = 74.35kN·m øMny = 84.50kN·m
Muy / øMny = 0.880 → O.K
(2) Calculate moment capacity (Direction Y)
ø = 0.900
Mux = 60.93kN·m øMnx = 81.85kN·m
Mux / øMnx = 0.744 → O.K

10. Check Rebar

(1) Calculate minimum rebar area required
As,min = 0.00200D = 0.000366m²
2025-07-01 18:19 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F2

(2) Calculate minimum rebar space required (Direction Y)

As = 0.000200m² (#[email protected])
sreq. = 0.167m
sx = 0.150m < sreq. = 0.167m → O.K
(3) Calculate minimum rebar space required (Direction X)
As = 0.000200m² (#[email protected])
sreq. = 0.167m
sy = 0.150m < sreq. = 0.167m → O.K

2025-07-01 18:19 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F3

1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ] 3.20
2.68 0.52
2. Material
(1) F'c : 20,684KPa
(2) Fy : 227,600KPa

1.60
3. Section
(1) Section Size

3.20
Depth : 0.450m
Cover : 0.0800m Y1
(2) Column Section

1.60
Shape of Column : Rectangle
X1
Section : 0.850x0.800m
Eccentricity (X) : 1.075m
Eccentricity (Y) : 0.000m

4. Rebar
(1) Direction Y
Layer 1 : #[email protected] (As = 0.000305m²)
2.75

Layer 2 : #[email protected] (As = 0.000305m²)

(2) Direction X
Layer 1 : #[email protected] (As = 0.000305m²)
Layer 2 : #[email protected] (As = 0.000305m²)
0.45

5. Foundation
(1) Foundation Size
Lx : 3.200m
Ly : 3.200m
fe : 427kN/m²

6. Design Load
(1) Service Load
Ps : 464kN
Msx : 55.38kN·m
Msy : 571kN·m
(2) Factored Load
Pu : 546kN
Mux : 76.47kN·m
Muy : 761kN·m
(3) Surcharge Load
Surface Load : 0.000kN/m²
Weight Density : 18.00kN/m³
Soil Height : 2.750m
(4) Self weight is considered.

7. Check Soil Capacity

(1) Calculate actual soil stress
qs,top-left = 0.000kN/m² qs,top-right = 390kN/m²
qs,bot-left = 0.000kN/m² qs,bot-right = 354kN/m²
qs,max = 390kN/m²
qs,max / fe = 0.913 → O.K

2025-07-01 18:21 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F3

(2) Calculate factored soil stress

qu,top-left = 0.000kN/m² qu,top-right = 531kN/m²
qu,bot-left = 0.000kN/m² qu,bot-right = 482kN/m²
qu,max = 531kN/m² qu,min = 0.000kN/m²

8. Check Shear
(1) Calculate one-way shear
ø = 0.750
Vux = 0.000kN øVcx = 656kN
Vux / øVcx = 0.000 → O.K
Vuy = 365kN øVcy = 628kN
Vuy / øVcy = 0.582 → O.K
(2) Calculate two-way shear
b0 Vc1 Vc2 Vc3 Vc Vu øVc
- Ratio
(m) (kN) (kN) (kN) (kN) (kN) (kN)
Interior 4.748 3,743 3,279 2,597 2,597 471 1,948 0.242
Edge(X) 3.424 2,699 2,422 1,873 1,873 485 1,405 0.345
Edge(Y) 5.574 4,394 3,009 3,049 3,009 292 2,257 0.129
Corner 3.312 2,611 1,896 1,811 1,811 318 1,359 0.234

INTERIOR EDGE( X ) EDGE( Y ) CORNER

ø = 0.750
d = 0.362m
4
Vc1 = ( 2 + ) f'c b0 d
β
as d
Vc2 = ( + 2 ) f'c b0 d
b0
Vc3 = 4 f'c b0 d
Vc = min(Vc1 , Vc2 , Vc3 )
Vu = 485kN
Vu / øVc = 0.345 → O.K

9. Check Moment Capacity

(1) Calculate moment capacity (Direction X)
ø = 0.900
Muy = 0.000kN·m øMny = 45.18kN·m
Muy / øMny = 0.000 → O.K
(2) Calculate moment capacity (Direction Y)
ø = 0.900
Mux = 37.52kN·m øMnx = 43.20kN·m
Mux / øMnx = 0.869 → O.K

10. Check Rebar

2025-07-01 18:21 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F3

(1) Calculate minimum rebar area required

As,min = 0.00200D = 0.000274m²
(2) Calculate minimum rebar space required (Direction Y)
As = 0.000200m² (#[email protected])
sreq. = 0.222m
sx = 0.200m < sreq. = 0.222m → O.K
(3) Calculate minimum rebar space required (Direction X)
As = 0.000200m² (#[email protected])
sreq. = 0.222m
sy = 0.200m < sreq. = 0.222m → O.K

2025-07-01 18:21 3
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F4

1. General Information
(1) Design Code : ACI318-14
(2) Code Unit : lbf, in
[ User defined unit system is applied. ( Unit System : kN, m ) ] 3.00
2.58 0.42
2. Material
(1) F'c : 20,684KPa
(2) Fy : 227,600KPa

3. Section
(1) Section Size

2.58
3.00
Depth : 0.600m
Cover : 0.0800m Y1
(2) Column Section
Shape of Column : Rectangle

0.42
X1
Section : 0.850x0.800m

4. Rebar
(1) Direction Y
Layer 1 : #[email protected] (As = 0.000865m²)
Layer 2 : #[email protected] (As = 0.000865m²)
(2) Direction X
2.60

Layer 1 : #[email protected] (As = 0.000406m²)

Layer 2 : #[email protected] (As = 0.000406m²)

5. Foundation
(1) Foundation Size
0.60

Lx : 3.000m
Ly : 3.000m
fe : 427kN/m²

6. Design Load
(1) Service Load
Ps : 222kN
Msx : 88.65kN·m
Msy : 390kN·m
(2) Factored Load
Pu : 273kN
Mux : 116kN·m
Muy : 538kN·m
(3) Surcharge Load
Surface Load : 0.000kN/m²
Weight Density : 18.00kN/m³
Soil Height : 2.600m
(4) Self weight is considered.

7. Check Soil Capacity

(1) Calculate actual soil stress
qs,top-left = 0.000kN/m² qs,top-right = 204kN/m²
qs,bot-left = 0.000kN/m² qs,bot-right = 305kN/m²
qs,max = 305kN/m²
qs,max / fe = 0.715 → O.K
(2) Calculate factored soil stress
qu,top-left = 0.000kN/m² qu,top-right = 281kN/m²

2025-07-02 15:23 1
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F4

qu,bot-left = 0.000kN/m² qu,bot-right = 439kN/m²

qu,max = 439kN/m² qu,min = 0.000kN/m²

8. Check Shear
(1) Calculate one-way shear
ø = 0.750
Vux = 0.000kN øVcx = 870kN
Vux / øVcx = 0.000 → O.K
Vuy = 813kN øVcy = 841kN
Vuy / øVcy = 0.968 → O.K
(2) Calculate two-way shear
b0 Vc1 Vc2 Vc3 Vc Vu øVc
- Ratio
(m) (kN) (kN) (kN) (kN) (kN) (kN)
Interior 5.348 5,962 6,029 4,137 4,137 218 3,103 0.0704
Edge(X) 3.524 3,929 4,334 2,726 2,726 259 2,044 0.127
Edge(Y) 3.524 3,929 4,334 2,726 2,726 257 2,044 0.126
Corner 2.187 2,438 2,826 1,692 1,692 290 1,269 0.229

INTERIOR EDGE( X ) EDGE( Y ) CORNER

ø = 0.750
d = 0.512m
4
Vc1 = ( 2 + ) f'c b0 d
β
as d
Vc2 = ( + 2 ) f'c b0 d
b0
Vc3 = 4 f'c b0 d
Vc = min(Vc1 , Vc2 , Vc3 )
Vu = 290kN
Vu / øVc = 0.229 → O.K

9. Check Moment Capacity

(1) Calculate moment capacity (Direction X)
ø = 0.900
Muy = 0.000kN·m øMny = 84.50kN·m
Muy / øMny = 0.000 → O.K
(2) Calculate moment capacity (Direction Y)
ø = 0.900
Mux = 115kN·m øMnx = 167kN·m
Mux / øMnx = 0.690 → O.K

10. Check Rebar

(1) Calculate minimum rebar area required
As,min = 0.00200D = 0.000366m²
2025-07-02 15:23 2
MIDASIT http://www.midasuser.com
TEL:1-646-852-9286

MEMBER NAME : F4

(2) Calculate minimum rebar space required (Direction Y)

As = 0.000284m² (#[email protected])
sreq. = 0.237m
sx = 0.100m < sreq. = 0.237m → O.K
(3) Calculate minimum rebar space required (Direction X)
As = 0.000200m² (#[email protected])
sreq. = 0.167m
sy = 0.150m < sreq. = 0.167m → O.K

2025-07-02 15:23 3
LOWER GROUND PLAN

UPPER GROUND PLAN

2nd FLOOR PLAN & CANOPY

3RD FLOOR PLAN

ROOF BEAM PLAN

ROOF FRAMING PLAN

COLUMNS

Eastgrove (Summary) Final 1 66
No ratings yet
Eastgrove (Summary) Final 1 66
66 pages
Eastgrove Summary 07.16.25
No ratings yet
Eastgrove Summary 07.16.25
144 pages
Structural Analysis AND Design For The Proposed Three (3) - Storey Commercial Building With Roofdeck
No ratings yet
Structural Analysis AND Design For The Proposed Three (3) - Storey Commercial Building With Roofdeck
155 pages
Structural Wind Load Analysis
No ratings yet
Structural Wind Load Analysis
89 pages
WLX Calc
No ratings yet
WLX Calc
2 pages
WX Specification
No ratings yet
WX Specification
5 pages
Midas Gen: Project Title
No ratings yet
Midas Gen: Project Title
3 pages
WIND
No ratings yet
WIND
3 pages
Wind Load Cal. Sheet
No ratings yet
Wind Load Cal. Sheet
3 pages
Wind Load Analysis for Engineers
No ratings yet
Wind Load Analysis for Engineers
3 pages
Viento
No ratings yet
Viento
4 pages
Engsolutions RCB: Wind Loads Nsr-10
No ratings yet
Engsolutions RCB: Wind Loads Nsr-10
4 pages
Wind Load Analysis for Project VIENTO
No ratings yet
Wind Load Analysis for Project VIENTO
4 pages
Analisis de Viento
No ratings yet
Analisis de Viento
4 pages
Viento Re
No ratings yet
Viento Re
4 pages
Wind Load On The Roof
No ratings yet
Wind Load On The Roof
14 pages
MecaWind Tank Output
No ratings yet
MecaWind Tank Output
3 pages
Structural Load Analysis Report
100% (2)
Structural Load Analysis Report
48 pages
Wind Load Analysis for Flat Roofs
No ratings yet
Wind Load Analysis for Flat Roofs
5 pages
WPFOutpu
No ratings yet
WPFOutpu
2 pages
Paseo Curtain Wall Strutural Calculation
100% (2)
Paseo Curtain Wall Strutural Calculation
79 pages
An Example Problem On Wind Load Calculation According To NSCP 2010
89% (9)
An Example Problem On Wind Load Calculation According To NSCP 2010
32 pages
An Example Problem On Wind Load Calculation According To NSCP 2010
No ratings yet
An Example Problem On Wind Load Calculation According To NSCP 2010
32 pages
Wndload - Monoslope - ASCE 7-22
No ratings yet
Wndload - Monoslope - ASCE 7-22
5 pages
Structural Calcs SHED
No ratings yet
Structural Calcs SHED
24 pages
Wind Loading in Accordance With ASCE7-10 Using The Directional Design Method
No ratings yet
Wind Loading in Accordance With ASCE7-10 Using The Directional Design Method
6 pages
Structural Analysis: One-Storey Building
50% (2)
Structural Analysis: One-Storey Building
26 pages
NSCP 2010 Wind Load Calculation Example
No ratings yet
NSCP 2010 Wind Load Calculation Example
32 pages
WH04.Wind Loads
No ratings yet
WH04.Wind Loads
6 pages
WindBBV1.0 Thinh
No ratings yet
WindBBV1.0 Thinh
2 pages
Wind Load Analysis for Engineers
100% (1)
Wind Load Analysis for Engineers
6 pages
Binder 1
No ratings yet
Binder 1
34 pages
Wind Load Analysis per IS 875 Guidelines
75% (4)
Wind Load Analysis per IS 875 Guidelines
51 pages
As-Nz 1170.2.2002 - Windload
100% (1)
As-Nz 1170.2.2002 - Windload
24 pages
Roof Structural Analysis PDF
No ratings yet
Roof Structural Analysis PDF
11 pages
WPFOutput2024 09 27 15 22 24 945
No ratings yet
WPFOutput2024 09 27 15 22 24 945
5 pages
Wind Loading ASCE 17-16
100% (5)
Wind Loading ASCE 17-16
18 pages
Wind Load Parameters NSR-10
No ratings yet
Wind Load Parameters NSR-10
9 pages
Wind Load
No ratings yet
Wind Load
11 pages
Wind Loading (ASCE7)
No ratings yet
Wind Loading (ASCE7)
7 pages
Wind Load Calculation for Low-Rise Buildings
No ratings yet
Wind Load Calculation for Low-Rise Buildings
10 pages
Structural Analysis - 17 Storey Apartment Building PDF
No ratings yet
Structural Analysis - 17 Storey Apartment Building PDF
107 pages
Sachpazis - Wind Loading Analysis - Design For A Hipped Roof Example According To En1991 1 4 - Apr 2016
No ratings yet
Sachpazis - Wind Loading Analysis - Design For A Hipped Roof Example According To En1991 1 4 - Apr 2016
7 pages
Duopitch Roof Example
100% (1)
Duopitch Roof Example
6 pages
Site Criteria and Loads On Structure
No ratings yet
Site Criteria and Loads On Structure
7 pages
Estimation of Wind Loads: CE 115 Structural Theory Ii
No ratings yet
Estimation of Wind Loads: CE 115 Structural Theory Ii
13 pages
Estimation of Wind Loads: CE 115 Structural Theory Ii
No ratings yet
Estimation of Wind Loads: CE 115 Structural Theory Ii
12 pages
Wind Asce7 16 5 PDF Free
No ratings yet
Wind Asce7 16 5 PDF Free
18 pages
Wind Load Calculation IS:875 Software
100% (2)
Wind Load Calculation IS:875 Software
46 pages
Solved Examples Based On Draft IS875pt.3-2nd Ed
No ratings yet
Solved Examples Based On Draft IS875pt.3-2nd Ed
94 pages
Solved Examples Based On Draft IS875pt.3-1st Ed
100% (1)
Solved Examples Based On Draft IS875pt.3-1st Ed
85 pages
Wind Load Calculations Report
No ratings yet
Wind Load Calculations Report
5 pages
Wind Load Calculation Report
100% (4)
Wind Load Calculation Report
26 pages
V Class: Client: Date: Author: Job #: Project: Subject: Webinar Example 1 References
No ratings yet
V Class: Client: Date: Author: Job #: Project: Subject: Webinar Example 1 References
16 pages
Wind Load Calculation
No ratings yet
Wind Load Calculation
3 pages
Eastgrove Summary 07.22.25 2.4kpa-1-84
No ratings yet
Eastgrove Summary 07.22.25 2.4kpa-1-84
84 pages
Bs1 Footing Sum
No ratings yet
Bs1 Footing Sum
2 pages
Plans S1
No ratings yet
Plans S1
1 page
B1 Sum
No ratings yet
B1 Sum
1 page
B1 Sum
No ratings yet
B1 Sum
1 page
Ground Floorplan Second Floorplan Second Floorplan: Scale: 1:250 MTS Scale: 1:250 MTS Scale: 1:250 MTS
No ratings yet
Ground Floorplan Second Floorplan Second Floorplan: Scale: 1:250 MTS Scale: 1:250 MTS Scale: 1:250 MTS
5 pages
Refresher4A - MSTHC.v2
No ratings yet
Refresher4A - MSTHC.v2
11 pages
Plans P2
No ratings yet
Plans P2
1 page
Actual Alignment
No ratings yet
Actual Alignment
1 page
Angle
No ratings yet
Angle
1 page
Plans S3
No ratings yet
Plans S3
1 page
Plans P3
No ratings yet
Plans P3
1 page
Lunar Tix
No ratings yet
Lunar Tix
1 page
Green Engineering Principles
No ratings yet
Green Engineering Principles
13 pages
HW350X350
No ratings yet
HW350X350
9 pages
Boundary Alignment
No ratings yet
Boundary Alignment
1 page
L1 Sum
No ratings yet
L1 Sum
1 page
Terrace
No ratings yet
Terrace
1 page
Midas Gen: Project Title
No ratings yet
Midas Gen: Project Title
8 pages
Office Floor Plan Layout
No ratings yet
Office Floor Plan Layout
1 page
New GRND
No ratings yet
New GRND
1 page
1
No ratings yet
1
1 page
AC Circuits Review Items
No ratings yet
AC Circuits Review Items
2 pages
Weather Maps & Station Models
No ratings yet
Weather Maps & Station Models
25 pages
Master Thesis - Laser Weld Heat Distortions in Thin Plates - Valter Sousa Carrolo
No ratings yet
Master Thesis - Laser Weld Heat Distortions in Thin Plates - Valter Sousa Carrolo
100 pages
Physics Problems for JEE Advanced
No ratings yet
Physics Problems for JEE Advanced
83 pages
I-P A19 Ch6 Indoor Swimming Pools
No ratings yet
I-P A19 Ch6 Indoor Swimming Pools
9 pages
Lecture 5
No ratings yet
Lecture 5
39 pages
History and Concepts of Biofluid Mechanics
No ratings yet
History and Concepts of Biofluid Mechanics
53 pages
Understanding Redox Reactions
No ratings yet
Understanding Redox Reactions
11 pages
Rectangular Sedimentation Tank Overview
No ratings yet
Rectangular Sedimentation Tank Overview
5 pages
Magnetism and Electromagnetism Concepts
No ratings yet
Magnetism and Electromagnetism Concepts
34 pages
An Electrically and Mechanically Self-Healing Composite With Pressure - and Flexion-Sensitive Properties For Electronic Skin Applications
No ratings yet
An Electrically and Mechanically Self-Healing Composite With Pressure - and Flexion-Sensitive Properties For Electronic Skin Applications
8 pages
K04 - Variable Acceleration (Split Journey) QP
No ratings yet
K04 - Variable Acceleration (Split Journey) QP
6 pages
ESQch 7
No ratings yet
ESQch 7
5 pages
Quantum Mechanics Take-Home Exam
No ratings yet
Quantum Mechanics Take-Home Exam
2 pages
Mance Qualification Tests. They Are Given To Find Out: 900 Chapter 28 Joint Design, Testing, and Inspection
No ratings yet
Mance Qualification Tests. They Are Given To Find Out: 900 Chapter 28 Joint Design, Testing, and Inspection
9 pages
2025 Wassce Physics 2 Solution
No ratings yet
2025 Wassce Physics 2 Solution
6 pages
Cambridge International AS & A Level: GEOGRAPHY 9696/11
No ratings yet
Cambridge International AS & A Level: GEOGRAPHY 9696/11
4 pages
Semiconductor Physics Basics
No ratings yet
Semiconductor Physics Basics
5 pages
10 Different Welding Tools and Equipment
81% (16)
10 Different Welding Tools and Equipment
3 pages
l12 BRG BL MH SH & Plume Rise
No ratings yet
l12 BRG BL MH SH & Plume Rise
58 pages
Quanta Windows 7 User Operation Manual
No ratings yet
Quanta Windows 7 User Operation Manual
234 pages
Ch. 1
No ratings yet
Ch. 1
3 pages
29 Morkel
No ratings yet
29 Morkel
14 pages
Abdullah Diploma 2021.06.11
No ratings yet
Abdullah Diploma 2021.06.11
90 pages
Synthesis of New Kind of Macroporous Polyvinyl-Alcohol Formaldehyde Based Sponges and Its Water Superabsorption Performance
No ratings yet
Synthesis of New Kind of Macroporous Polyvinyl-Alcohol Formaldehyde Based Sponges and Its Water Superabsorption Performance
11 pages
12 Physics Part 01
No ratings yet
12 Physics Part 01
21 pages
Structural Steel Design Training Course
No ratings yet
Structural Steel Design Training Course
9 pages
Cadiangullong Dam RCC Thermal Stress Analysis
No ratings yet
Cadiangullong Dam RCC Thermal Stress Analysis
13 pages
Base Plate Bearing on Concrete Analysis
No ratings yet
Base Plate Bearing on Concrete Analysis
2 pages
IB Chemistry Chapter 7 Definition List
No ratings yet
IB Chemistry Chapter 7 Definition List
6 pages
1 s2.0 S135964621730101X Main
No ratings yet
1 s2.0 S135964621730101X Main
5 pages