;yy; ®
MATERIAL SAFETY DATA SHEET
Product Health and Safety Data
PRODUCT: HF-95X, HF-95Y, HF-95Z
SECTION I – IDENTIFICATION OF THE SUBSTANCE/PREPARATIONS/SUPPLIER
;yy;
P.O. Box 3241
Milwaukee, WI 53201-3341, USA
PRODUCT: HF-95X, HF-95Y, HF-95Z
SUPPLIER: Enerpac B.V., Storkstraat 25, 3905 KX Veenendaal, The Netherlands,
Tel.: +31 318 535 911
PRODUCT CODE: BSL919885
DESCRIPTION: Hydraulic Fluid
For specific application advice see the appropriate Instruction Sheet or contact your Enerpac representative.
REVISION: 4 April 2002
SUPERSEDES: 12 NOVEMBER 1996
REVISION CHANGES:
Updated.
EMERGENCY TELEPHONE NUMBERS:
Netherlands: 010 4175 111 NVIC: 030 274 88 88 [This number should be called, in case of an
emergency, only by the referred medical doctor in charge.)
Belgium: 03 286 08 11 A + E centre: 070 245 245
SECTION II – COMPOSITION/INFORMATION ON INGREDIENTS
CHEMICAL COMPOSITION: Highly refined oil (IP 346 DMSO extract <3%)
Proprietary performance additives.
HAZARDOUS INGREDIENT: No component is present at sufficient concentration to require a hazardous
classification.
SECTION III – HAZARD IDENTIFICATION
This material is not considered to be hazardous, but should be handled in accordance with good industrial hygiene
and safety practices. In common with most mineral oils, prolonged and repeated skin contact may cause dermatitis.
Note: High Pressure Applications
Injections through the skin resulting from contact with the product at high pressure constitute a major medical
emergency.
See "Medical Advice" Under First-Aid Measures, Section 4 of this Safety Data Sheet.
Handling precautions should be strictly observed.
SECTION IV – FIRST AID MEASURES
EYES:
Wash eye thoroughly with copious quantities of water, ensuring eyelids are held open. Obtain medical advice if any
pain or redness develops or persists.
(1)
;yy; ®
MATERIAL SAFETY DATA SHEET
Product Health and Safety Data
PRODUCT: HF-95X, HF-95Y, HF-95Z
SECTION IV – FIRST AID, cont.
;yy;
P.O. Box 3241
Milwaukee, WI 53201-3341, USA
SKIN CONTACT:
Wash skin thoroughly with soap and water as soon as reasonably practicable. Remove heavily contaminated clothing
and wash underlying skin.
INGESTION:
If contamination of the mouth occurs, wash out thoroughly with water.
Except as a deliberate act, the ingestion of large amounts of product is unlikely. If it should occur, do not induce
vomiting; obtain medical advice.
MEDICAL ADVICE:
Treatment should in general be symptomatic and directed to relieving any effects.
Note: High Pressure Applications
Injections through the skin, resulting from contact with the product at high pressure, constitute a major medical
emergency. Injuries may not appear serious at first but within a few hours tissue becomes swollen, discolored and
extremely painful with extensive subcutaneous necrosis.
Surgical exploration should be undertaken without delay. Thorough and extensive debridement of the wound and
underlying tissue is necessary to minimize tissue loss and prevent or limit permanent damage. Note that high
pressure may force the product considerable distances along tissue planes.
SECTION V – FIRE-FIGHTING MEASURES
Use foam, dry powder or water fog. DO NOT USE water jets.
Fires in confined spaces should be dealt with by trained personnel wearing approved breathing apparatus.
Water may be used to cool nearby heat exposed areas/objects/packages. Avoid spraying directly into storage
containers because of the danger of boil-over.
COMBUSTION PRODUCTS:
Toxic fumes may be evolved on burning or exposure to heat.
See Stability and Reactivity, Section 10 of this Safety Data Sheet.
SECTION VI – ACCIDENTAL RELEASE MEASURES
PERSONAL PRECAUTIONS: See Section 8.
Contain and recover spilled material using sand or other suitable inert absorbent material.
It is advised that stocks of suitable absorbent material should be held in quantities sufficient to deal with any spillage
which may be reasonably anticipated.
Spilled material may make surfaces slippery.
Protect drains from potential spills to minimize contamination. Do not wash product into drainage system.
In the case of large spills contact the appropriate authorities.
In the case of spillage on water, prevent the spread of product by the use of suitable barrier equipment. Recover
product from the surface. Protect environmentally sensitive areas and water supplies.
(2)
;yy; ®
MATERIAL SAFETY DATA SHEET
Product Health and Safety Data
PRODUCT: HF-95X, HF-95Y, HF-95Z
SECTION VII – HANDLING AND STORAGE
;yy;
P.O. Box 3241
Milwaukee, WI 53201-3341, USA
HANDLING PRECAUTIONS:
Avoid contact with eyes. If splashing is likely to occur wear a full face visor or chemical goggles as appropriate.
Avoid frequent or prolonged skin contact with fresh or used product.
Good working practices, high standards of personal hygiene and plant cleanliness must be maintained at all times.
Wash hands thoroughly after contact.
Use disposable cloths and discard when soiled. Do not put soiled cloths into pockets.
FIRE PREVENTION:
Product contaminated rags, paper or material used to absorb spillage, represent a fire hazard, and should not be
allowed to accumulate. Dispose of safely immediately after use.
STORAGE CONDITIONS:
Store under cover and protect from heat and sources of ignition.
LOAD/UNLOAD TEMPERATURE deg. C: Ambient to 40
STORAGE TEMPERATURE deg. C: Ambient to 40
SPECIAL PRECAUTIONS:
Keep containers closed when not in use.
Prevent small spills and leakages to avoid slip hazard.
SECTION VIII – EXPOSURE CONTROLS AND PERSONAL PROTECTION
EXPOSURE LIMITS:
There is no appropriate occupational exposure limit for this material.
Ensure good ventilation.
Avoid, as far as reasonably practicable, inhalation of vapor, mists or fumes generated during use.
If vapor, mists or fumes are generated, their concentration in the workplace air should be controlled to the lowest
reasonably practicable level.
PROTECTIVE CLOTHING:
Wear face visor or goggles in circumstances where eye contact can accidentally occur.
If skin contact is likely, wear impervious protective clothing and/or gloves.
Protective clothing should be regularly laundered or dry cleaned. Change heavily contaminated clothing as soon as
reasonably possible; dry clean, launder and preferably starch before re-use. Wash any contaminated underlying skin
with soap and water.
RESPIRATORY PROTECTION:
Respiratory protection is unnecessary, provided the concentration or vapor, mists or fumes is adequately controlled.
The use of respiratory equipment must be strictly in accordance with the manufactures’ instructions and any
statutory requirements governing its selection and use.
(3)
;yy; ®
MATERIAL SAFETY DATA SHEET
Product Health and Safety Data
PRODUCT: HF-95X, HF-95Y, HF-95Z
SECTION IX – PHYSICAL AND CHEMICAL PROPERTIES
;yy;
P.O. Box 3241
Milwaukee, WI 53201-3341, USA
TYPICAL VALUES
Grades: Test Method Units
Physical state liquid
Color blue
Odor oily
Density @ 15°C ASTM D 1298 kg/m3 878
Kinematic viscosity @ 40°C ASTM D 445 mm2/s 32
Pour point ASTM D 97 %C max –30
SECTION X – STABILITY AND REACTIVITY
Products of this type are stable and unlikely to react in a hazardous manner under normal conditions of use.
Hazardous polymerization reactions will not occur.
This material is combustible.
MATERIALS TO AVOID:
Avoid contact with strong oxidizing agents.
HAZARDOUS DECOMPOSITION PRODUCTS:
Thermal decomposition products will vary with conditions.
Incomplete combustion will generate smoke, carbon dioxide and hazardous gases, including carbon monoxide.
SECTION XI – TOXICOLOGICAL INFORMATION
EYES:
Unlikely to cause more than transient stinging or redness if accidental eye contact occurs.
SKIN:
Unlikely to cause harm to the skin on brief or occasional contact but prolonged or exposure may lead to dermatitis.
INGESTION:
Unlikely to cause harm if accidentally swallowed in small doses, though larger quantities may cause nausea and
diarrhea.
INHALATION:
At normal ambient temperatures this product will be unlikely to presents an inhalation hazard because of its
volatility.
May cause irritation to eyes, nose and throat due to exposure to vapor, mists or fumes. May be harmful by
inhalation if exposure to vapor, mists or fumes thermal decomposition products occurs.
(4)
;yy; ®
MATERIAL SAFETY DATA SHEET
Product Health and Safety Data
PRODUCT: HF-95X, HF-95Y, HF-95Z
SECTION XII – ECOLOGICAL INFORMATION
;yy;
P.O. Box 3241
Milwaukee, WI 53201-3341, USA
MOBILITY:
Spillage may penetrate the soil causing ground water contamination
PERSISTENCE AND DEGRADABILITY:
This product is inherently biodegradable.
BIO-ACCUMULATIVE POTENTIAL:
There is no evidence to suggest bio-accumulation will occur.
AQUATIC TOXICITY:
Spill may form a film on water surfaces causing physical damage to organisms. Oxygen transfer could also be
impaired.
SECTION XIII – DISPOSAL CONSIDERATIONS
Where possible, arrange for product to be recycled.
Dispose of via an authorized person/licensed waste disposal contractor in accordance with local regulations.
Incineration may be carried out under controlled conditions provided that local regulations for emissions are met.
SECTION XIV – TRANSPORT INFORMATION
Not classified as hazardous for transport (ADR, RID,UN, IMO, IATA/ICAO)
Rail cars, tank trucks, drums. All firmly closed during transportation with zero leakage. Shipping containers have to
be fully resistant against highly refined mineral-based oils.
TRANSPORT TEMPERATURE deg. C: Ambient to 40ºC
SECTION XV – REGULATORY INFORMATION
Not classified as hazardous for supply.
Refer to your national legislation implementing the EC Directive 91/155/EG
(5)
;yy; ®
MATERIAL SAFETY DATA SHEET
Product Health and Safety Data
PRODUCT: HF-95X, HF-95Y, HF-95Z
SECTION XVI – OTHER INFORMATION
;yy;
P.O. Box 3241
Milwaukee, WI 53201-3341, USA
Translated by:
Enerpac B.V.
Storkstraat 25
3905 KX Veenendaal
The Netherlands
This data sheet and the health, safety and environmental information it contains is considered to be accurate as of
the date specified above. We have reviewed any information contained herein which we received from sources
outside Enerpac and the Actuant Corp. However, no warranty or representation, express or implied is made as to
the accuracy or completeness of the data and information contained in this data sheet.
Health an safety precautions and environmental advice noted in this data sheet may not be accurate for all
individuals and/or situations. It is the user’s obligation to evaluate and use this product safely and to comply with all
applicable laws and regulations.
No statement made in this data sheet shall be construed as a permission, recommendation or authorization given
or implied to practice any patented invention without a valid license. Enerpac and the Actuant Corp. shall not be
responsible for any damage or injury resulting from abnormal use of the material, from any failure to adhere to
recommendations, or from any hazards inherent in the nature of the material.
(6)
