https://DNCdevice.
com
DNC Transmitter
TITAN
User manual
https://DNCdevice.com
1. Design Features & Features
https://DNCdevice.com
2.4 inch LCD screen, 65536 colors: program display, File & Folder list, intuitive and dynamic ...
2Gb / 4Gb / 8Gb internal memory for storing and
Power ON / OFF switch managing the program
Two USB 2.0 ports
RS232 and Parallel 50-pin communication
04 magnets for easy installation
06 button: RESET, FUNCTION, BACK, SET, UP, DOWN
Functions: COPY-PASTE, CUT-PASTE, RENAME, NEW FOLDER, DELETE File & Folder
management, USB data management and MEMORY
AUTO CUTTING feature - Allows you to set Cut Per Percentage (%) and Cut Number by Line
Number (N); View the content of the program after cutting
SEND feature - Transmit program for CNC machine, view G-code content being transmitted
FORCED SEND - Forces the program into a CNC machine
RECEIVE - Receive program / Parameter from CNC machine
2. Power to TITAN
2.1. Used from CNC machine
TITAN can be powered by CNC machines via data cables.
For RS232 serial communication, most CNC transmitters through this port simultaneously
provide DC24V power. Pinning one 25-pin cable to the CNC machine, the other 9-pin cable
pinned to TITAN for power.
When pinning the RS232 cable that can not power TITAN, the installer can manually
connect DC24V power from the CNC machine to the 25 pin of DB25.
For parallel transmission, the CNC machine is powered by a 50-pin cable. Pin the cable to
TITAN for power.
2.2. External power supply
When it is not possible to obtain power from a CNC machine, it is necessary to provide
external power to TITAN using a separate power supply.
Input 100 ÷ 240 VAC
50/60 Hz
Way out 7 ÷ 40 VDC
Use 12V or 24V
Output ≥ 1.5A
current
https://DNCdevice.com
It is recommended to use Adapter with wide input voltage range to take advantage of 100VAC
1A available on CNC machine.
Note at a time only power supply for TITAN in a single way.
3. File contained in USB and MEMORY
In a folder, TITAN can display File no more than 24, Folder number not more than 24.
That means there are up to 24 files and 24 folders in a folder.
Up to 10 class folders.
It can read up to the files contained in USB or MEMORY
4. Installation instructions
Way to install:
Press the RESET button and then hold down the SET button until the setting appears.
Or press the FUCTIONS button, select the item:
https://DNCdevice.com
4.1. Save & Exit
- After install complete, select 1. Save & Exit to save the information and exit from install pages.
- Or click node BACK at Main Menu with the Save & Exit.
4.2. Load Default
- If you want to keep the previous settings information, select NO.
- If you want to enter the default value, select YES.
- SET button to select.
Default value table of the parameters:
Drive MEMORY & USB
Communication/Protocol RS232
Communication/Flow Control SOFTWARE
Communication/Code ASCII/ISO
Communication/Baud Rate 9600
Communication/Data Bits 7
Communication/Parity EVEN
Communication/Stop Bits 2
Communication/Line Delay 0
4.3. Drive
MEMORY & USB: Use USB and MEMORY.
USB ONLY: Use only USB.
MEMORY ONLY: Use only MEMORY.
https://DNCdevice.com
4.4. Communication
Protocol
RS232 PARALLEL
Flow Control SOFTWARE Speed F1 (350bytes/s)
HARDWARE F2 (400bytes/s)
F3 (450bytes/s)
F4 (500bytes/s)
F5 (550bytes/s)
F6 (600bytes/s)
F7 (650bytes/s)
Code ASCII / ISO Code ISO
EIA EIA
Baudrate 1200
2400
4800
9600
19200
38400
115200
Data Bits 7
8
Parity NONE
EVEN
ODD
Stop Bits 1
2
Line Delay (EOL) 0 ÷ 255
https://DNCdevice.com
4.5. Miscellaneous
Memory Capacity: Check the capacity of MEMORY
USB Capacity: Check USB storage
Format Drive:
If open in MEMORY, selecting this entry will go to Format MEMORY again.
If open in USB, when selecting this item will go to Format USB again.
Select YES to start Format.
View mode:
Choose how to display the program when transmitting.
SEND Monitoring ON: During RS232 transmission, the program will display the screen
during transmission.
https://DNCdevice.com
SEND Monitoring OFF: RS232 transmission will not show the program but only show
transmitted percentage (%) and number of transmitted commands (N).
When transmitting at high speed (Baudrate> 19200), SEND Monitoring OFF should be
selected so that the baud rate is guaranteed.
5. FUNCTIONS – The functions of the TITAN transmitter
1. COPY – PASTE
Use COPY-PASTE to copy a file from the source folder to the destination folder.
Step 1: Use the UP / DOWN / BACK / SET buttons to select the file to copy.
Step 2: Press the FUNCTIONS button,
select COPY
Step 3: Use the UP / DOWN / BACK / SET buttons to navigate to the destination folder.
Step 4: Press the FUNCTIONS button,
select PASTE
https://DNCdevice.com
Step 5: Wait for the copy process to
proceed
Note:
- The file copy speed is 30Mbytes / min (0.5Mb / s).
- If there is a file with the same name as the duplicate file, it will be overwritten do not ask.
2. CUT – PASTE
Use CUT-PASTE to cut a file from the source folder to the destination folder.
Step1: Use the UP / DOWN / BACK / SET buttons to select the file you want to cut.
Step 2: Press the FUNCTIONS button,
select CUT
Step 3: Use the UP / DOWN / BACK / SET buttons to navigate to the destination folder.
Step 4: Press the FUNCTIONS button,
select PASTE
Step 5: Wait for the cutting process to
proceed
Note: If the CUT-PASTE process takes
place within the USB or internal
MEMORY, the MOVING display.
3. RENAME
Use RENAME to rename the file or folder.
Step 1: Use the UP / DOWN / BACK / SET buttons to select the file / folder to rename.
https://DNCdevice.com
Step 2: Press the FUNCTIONS button,
select RENAME
Step 3: Name new keyboard:
- Use the UP / DOWN buttons to move to
the desired character.
- Press SET to select the character.
- Press the BACK button to backspace.
- Press the FUNCTIONS button to create
a blank space.
- Select ENTER to complete the naming.
When renaming files, only change the name, can not change the file extension.
4. NEW FOLDER
Use to create a new folder
Step 1: Use the UP / DOWN / BACK / SET buttons to navigate to the directory.
Step 2: Press the FUNCTIONS button,
select NEW FOLDER
Step 3: Name new keyboard:
- Use the UP / DOWN buttons to move to
the desired character.
- Press SET to select the character.
- Press the BACK button to backspace.
- Press the FUNCTIONS button to create
a blank space.
- Select ENTER to complete the naming.
The default name is automatically set to New Folder x, where x is the sequence number.
If you want to get the default name, press the SET button.
5. DELETE
Use to delete File or Folder
Step 1: Use the buttons: UP / DOWN / BACK / SET to go to File / Folder to delete.
Step 2: Press the FUNCTIONS button,
select DELETE
https://DNCdevice.com
Only delete empty folders
6. SEND
Transfer program to CNC machine
Step 1: Use the buttons: UP / DOWN /
BACK / SET to open the program to
transmit.
Step 2: TITAN is now ready for
transmission. Can operate on CNC
machine to start transmission.
(Or press the FUNCTIONS button, select
SEND, then the READY display - ready
to transmit)
Step 3: Transmission process, the
display:
- The name of the program being
transmitted.
- Communication parameters (RS232 /
PARALLEL).
- Percentage (%) of transmitted
programs.
- The number of lines (Lines) passed.
- Tx transfer, where x is the sequence
number.
- The program is streaming.
- scroll bar.
https://DNCdevice.com
Step 4: After completing transmission,
TITAN will automatically READY for the
next transmission (T number increases
by one unit).
Continue transmission, or press the
BACK button to exit.
7. FORCED SEND
Forcing a program into a CNC machine without the required signal from a CNC machine (Skip
XON)
Step 1: Use the buttons: UP / DOWN /
BACK / SET to open the program to
transmit.
Step 2: Press the FUNCTIONS button,
select FORCED SEND
Step 3: The transmission process takes
place.
After the transmission ends, TITAN
automatically exits the file list.
8. RECEIVE
Get program / parameter from CNC machine
Step 1: Use the buttons: UP / DOWN / BACK / SET to go to the desired folder containing the
receiving file.
Step 2: Press the FUNCTIONS button,
select RECEIVE
https://DNCdevice.com
Step 3: Name the file received by
the keyboard:
- Use the UP / DOWN buttons to
move to the desired character.
- Press SET to select the
character.
- Press the BACK button to
backspace.
- Press the FUNCTIONS button to
create a blank space.
- - Select ENTER to complete the
naming.
The default name is automatically
set to Receive x.txt, where x is the
sequence number. If you want to get the
default name, press the SET button.
Step 4: READY display - ready to receive
the program from the CNC machine
Step 5: Manipulate the CNC machine to
output the program.
At this point the display shows the
reception process:
- The number of bytes received.
- Show the current program
https://DNCdevice.com
Step 6: Wait for the reception process to
finish, then the FINISH display and
automatically exit.
9. AUTO CUTTING
Automatic program cut feature
Step 1: Use the UP / DOWN / BACK / SET buttons to select the file you want to cut.
Step 2: Press the FUNCTIONS button,
select AUTO CUTTING
Step 3: Option to cut in percentage or by
number of commands.
Step 4: Use the numeric keypad to set
the percentage or number of statements.
https://DNCdevice.com
Step 5: Wait for the cutting process to
proceed.
The execution speed is about
20Mbytes / min.
Step 6: After the cutting process is
complete, a folder called "Auto Cutting"
will be automatically created at the root
directory, containing new programs
created after cutting.
The name of the newly created file will
include the cut percentage or the number
of cut statements.
Notes about the automatic cutting program of TITAN
• If the percentage setting and command count are too small, TITAN will automatically get the
smallest percentage of 0.1% and the smallest statement is N100.
• TITAN can cut the program containing the following code:
% % Start% (required)
O Name of the program. Example: O001
S Spindle speed. Example: S800
F Processing speed. For example: F500.
M Effective M-code includes: M00, M01, M03 / M04, M05, M06, M08 / M09
Other M-codes, if present in the program, should be removed after cutting.
T The knife switch comes with M06.
G Effective G-code includes: G00, G01, G02, G03, G17/G18/G19, G28, G40,
G43, G49, G54/G55/G56/G57/G58/G59, G80, G90/G91, G92 .
If in the program to cut out the other G-code, TITAN will not be able to cut.
Note:
https://DNCdevice.com
When the program has G28, TITAN will transmit the following code:
G28Z0
G28X0Y0
When the program has G43 (eg G43H1), TITAN will transmit the
following code:
G0G43H1Z50.0
At the beginning of the program after cutting, TITAN always performs the structured
program as follows:
% % Early program
… … Pass the code needed (S, M, G, T ...)
F1000 F1000 Run to the point (X, Y) at the speed of
G1XxxxYxxx F1000, where (X, Y) is the starting
G1XxxxYxxx
coordinates of the next machining.
F100
F100 Down the Z axis at a speed of F100 to
Zxxx the depth of further processing
Zxxx
Fxxx
Fxxx Get the right speed at the starting point
…
… Continue to transmit the remaining
processing program
Warnings during cutting:
Error : “Not support Gxx” The cutting process detected in the
program that needs to be cut out
containing non-G-code (eg G81,
G83 ...) will warn the error: can not
cut because this G-code is not
supported.
Error: “Sign % Not Found” Could not find% top of program.
Error: “Line number too large” If you set the number of commands
larger than the actual command
https://DNCdevice.com
number of the program, then the
error.
Error: “Create File is corrupted” File creation failed.
For machining programs with multiple knives, the cutting process will allow the CNC
machine to replace the current knife to the knife.
After the cut is complete, the machine runs in Single Block and Dry Run mode to
execute each statement in advance, to check the optimal cutting percentage.
10. SETTINGS
Go to the settings page.
Press the FUNCTIONS button, select
https://DNCdevice.com
