HCD-XB6K

SERVICE MANUAL E Model

HCD-XB6K is the tuner, deck, CD and

amplifier section in LBT-XB6K.

Model Name Using Similar Mechanism HCD-XB6

CD CD Mechanism Type CDM37L-5BD29AL
Section Base Unit Name BU-5BD29AL
Optical Pick-up Name KSS-213D/Q-NP
Tape deck Model Name Using Similar Mechanism HCD-XB6
Section Tape Transport Mechanism Type TCM-220WR2

SPECIFICATIONS
Amplifier section Laser output Max. 44.6µF*
Continuous RMS power output *This output is the value measured at a distance
100+100 watts of 200 mm from the objective lens surface on the
(8 ohms at 1kHz, 10% THD) Optical Pick-up Block with 7 mm aperture.
Peak music power output 1400 watts Wavelength 780 - 790 nm
Inputs Frequency response 2 Hz - 20 kHz (±0.5 dB)
PHONO IN (phono jacks): sensitivity 3 mV, impedance 47 kilohms Signal-to-noise ratio More than 90 dB
VIDEO (AUDIO) IN (phono jacks):sensitivity 250 mV, impedance 47 Dynamic range More than 90 dB
kilohms
MIX MIC (phono jack): sensitivity 1 mV, impedance 10 kilohms Tape player section
Outputs Recording system 4-track 2-channel stereo
PHONES (stereo phone jack): accepts headphones of 8 ohms or more Frequency response (DOLBY NR OFF)
SPEAKER: accepts impedance of 8 to 16 ohms 60 - 13,000 Hz (±3 dB), using a Sony
SURROUND SPEAKER: accepts impedance of 16 ohms TYPE I cassette
60 - 14,000 Hz (±3 dB), using a Sony
CD player section TYPE II cassette
System Compact disc and digital audio system
Laser Semiconductor laser (λ = 780nm). – Continued on next page –
Emission duration: continuous

COMPACT DISC DECK RECEIVER

MICROFILM
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range 87.5 -108.0 MHz (50 kHz step)
Antenna FM wire antenna
Antenna terminals 75 ohm unbalanced
Intermediate frequency 10.7 MHz
AM tuner section
Tuning range 531 - 1,602 kHz
(with the tuning interval set at 9 kHz)
530 - 1,710 KHz
(with the tuning interval set at 10 kHz)
Antenna AM loop antenna, External antenna terminals
Intermediate frequency 450 kHz

General
Power requirements
Malaysian model: 220 - 240 V AC, 50/60 Hz
Other models: 110 - 120 V or 220 - 240 V AC, 50/60 Hz
Adjustable with voltage selector
Power consumption 190 watts
Dimensions (w/h/d) Approx. 355 x 425 x 435 mm (14 x 16 3/4 x 17 1/
4 in) incl. projecting parts and controls
Mass Approx. 12.5 kg (27 lb 9 oz.)
Supplied accessories: AM loop antenna (1)
Remote RM-SD70 (1)
Sony SUM-3 (NS) batteries (2)
FM wire antenna (1)
Speaker cords (2)

Design and specifications are subject to change without notice.

–2–
 CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.

Notes on chip component replacement

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.

This appliance is classified as a CLASS 1 LASER product.

The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.

Laser component in this product is capable of emitting radiation

exceeding the limit for Class 1.

The following caution label is located inside the unit.

Dolby noise reduction manufactured under license from Dolby

Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol a are trademarks of
Dolby Laboratories Licensing Corporation.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK ! OR DOTTED
LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.

–3–
 TABLE OF CONTENTS SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
1. GENERAL BLOCK OR BASE UNIT
Getting Started ................................................................... 5
Basic Operations ................................................................ 8 The laser diode in the optical pick-up block may suffer electro-
The CD Player ................................................................. 12 static break-down because of the potential difference generated
The Tape Deck ................................................................. 14 by the charged electrostatic load, etc. on clothing and the human
DJ Effects ........................................................................ 15 body.
Sound Adjustment ........................................................... 16 During repair, pay attention to electrostatic break-down and also
Other Features ................................................................. 18 use the procedure in the printed matter which is included in the
Additional Information .................................................... 21 repair parts.
The flexible board is easily damaged and should be handled with
care.
2. DISASSEMBLY .......................................................... 22
NOTES ON LASER DIODE EMISSION CHECK
3. TEST MODE ............................................................... 30
The laser beam on this model is concentrated so as to be focused
4. MECHANICAL ADJUSTMENTS ......................... 32 on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
5. ELECTRICAL ADJUSTMENTS sion, observe from more than 30 cm away from the objective lens.
DECK Section ................................................................. 32
TUNER Section ............................................................... 35 MODEL IDENTIFICATION
CD Section ....................................................................... 37 – BACK PANEL –

6. DIAGRAMS
6-1. Block Diagrams
TUNER Section ............................................................... 40
CD Section ....................................................................... 41
PARTS No.
DECK Section ................................................................. 42
MAIN Section ................................................................. 43
6-2. Schematic Diagram – KEY CONTROL Section – .......... 45
6-3. Printed Wiring Board – KEY CONTROL Section – ....... 45
6-4. Schematic Diagram – BD Section – ................................ 47
6-5. Printed Wiring Board – BD Section – ............................. 49
6-6 Schematic Diagram – CD MOTOR Section – ................ 51
6-7. Printed Wiring Boards – CD MOTOR Section – ........... 53
6-8. Schematic Diagram – TUNER Section – ....................... 55
6-9. Printed Wiring Board – TUNER Section – .................... 57
6-10. Printed Wiring Boards – DECK Section – ..................... 59
6-11. Schematic Diagram – DECK Section – .......................... 61 MODEL PARTS No.
6-12. Schematic Diagram – MAIN Section – .......................... 65 E, Indonesia models 4-987-926-4π
6-13. Printed Wiring Board – MAIN Section – ....................... 69
Saudi Arabia model 4-987-926-5π
6-14. Printed Wiring Boards – PANEL Section – ..................... 72
6-15. Schematic Diagrm – PANEL Section – ........................... 75 Singapore model 4-987-926-6π
6-16. Printed Wiring Boards – POWER Section – ................... 79 Malaysian model 4-987-926-7π
6-17. Schematic Diagram – POWER Section – ........................ 81
6-18. IC Pin Function Description ............................................ 89

7. EXPLODED VIEWS ................................................. 93

8. ELECTRICAL PARTS LIST ................................ 102

–4–
SECTION 1
GENERAL This section is extracted
from instruction manual.

–5–
–6–
–7–
–8–
–9–
– 10 –
– 11 –
– 12 –
– 13 –
– 14 –
– 15 –
– 16 –
– 17 –
– 18 –
– 19 –
– 20 –
– 21 –
 SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.

FRONT PANEL MAIN CD MECHANISM OPTICAL

CASE BASE UNIT BD BOARD
SECTION SECTION DECK SECTION PICK-UP
(Page 22) (Page 27) (Page 28)
(Page 23) (Page 24) (Page 24) (Page 28)
SLED
DISC TABLE MOTOR
(Page 27) (Page 28)

TAPE MECHANISM AUDIO BOARD CAPSTAN MOTOR

DECK SECTION (Page 29) (Page 29)
(Page 25)
CASSETTE
LID ASS’Y
(Page 25)

CD LID ASS’Y PANEL (A)/(B)

SECTION SUB ASS’Y
(Page 26) (Page 26)

MAIN BOARD
(Page 23)

Note: Follow the disassembly procedure in the numerical order given.

CASE

3 case 1 three screws

(case 3 point)

1 three screws
(case 3 point)

2 seven screws
(BVTT 3 × 6)

– 22 –
FRONT PANEL SECTION

1 three frat wires

(CN102, 205, 206)

3 front panel section

2 four screws
(BVTP 3 × 8)

MAIN BOARD

6 back panel

5 power cord

4 ereven screws
(BVTP 3 × 8)

3 connector
(CN901)
1 two flat wires
(CN1, 202)

9 MAIN board

IC201

8 connector
(CN101)

2 connector 7 two screws

(CN203) (BVTP 3 × 8)

– 23 –
MAIN SECTION

1 flat wire (CN202)

2 connector
(CN203)

4 main section

3 two screws
(BVTP 3 × 8)

3 screw
(BVTP 3 × 8)

3 two screws
(BVTP 3 × 8)

CD MECHANISM DECK SECTION

3 five screws
(BVTP 3 × 8)

4 CD mechanism
deck section

2 flat wire
and lead wire

1 Open the clamp.

– 24 –
TAPE MECHANISM DECK SECTION

4 three screws 4 three screws

(BVTP 2.6 × 8) (BVTP 2.6 × 8)

5 Remove the tape mechanism

deck section to direction of the arrow A.

3 two flat wires

(CN601, 1001)
A
2 Open the
cassette lids.

1 Push the
two buttons.

CASSETTE LID ASS’Y

3 two brackets

2 two screws
(BVTP 2.6 × 8)
1 two springs

– 25 –
CD LID ASS’Y SECTION

6 four screws
5 connector (BVTP 2.6 × 8)
(CN671)

7 CD lid ass’y

4 connector
(CN661)

2 four screws
(BVTP 2.6 × 8)

3 CD-B1 SW board

1 connector
(CN642)

PANEL (A) / (B) SUB ASS’Y

1 connector
(CN612)

3 two claws

2 four screws
(BVTP 2.6 × 8)

4 panel (A) sub ass’y

5 two claws

6 panel (B) sub ass’y

– 26 –
BASE UNIT

3 base unit

1 yoke bracket

2 boss

DISC TABLE

Note:
When the disc table is installed, adjust the positions
of roller cam and mark z as shown in the figure, then
set to the groove of disc table.

3 step screw
1 screw
(BVTP 3 × 8)

2 bracket (BU)
1 screw
(BVTP 3 × 8) 4 disc table

– 27 –
BD BOARD

1 two screws
(PTPWH M2.6 × 6) 1 two screws
(PTPWH M2.6 × 6)

2 optical pick-up
section
3 two springs

3 two springs
5 screw
(BVTP 2.6 × 8)

4 flat wire
(CN101)

6 Removal
the four solders.
7 BD board

limit switch

OPTICAL PICK-UP, SLED MOTOR

3 optical pick-up

4 two screws
(P2 × 3)

2 sled shaft

5 sled motor

1 claw

– 28 –
AUDIO BOARD

2 two rivets
1 connector
(CN651)

4 four screws
(BTP 2.6 × 4)

3 Break the soldering of two

flexible flat cables.

5 AUDIO board

CAPSTAN MOTOR
2 two screws
4 Removal the capstan motor (BTP 2.6 × 8)
to direction of the arrow.

1 Break the soldering of

motor lead.

3 claw

5 Hang the
two belts.

– 29 –
 SECTION 3
TEST MODE

[MC Cold Reset] [LED and Fluorescent Indicator Tube All Lit, Key Check
• The cold reset clears all data including preset data stored in the Mode]
RAM to initial conditions. Execute this mode when returning Procedure:
the set to the customer. 1. Press three buttons SPECTRUM ANALYZER , ENTER ,
Procedure: and DISC 3 simultaneously.
1. Press three buttons SPECTRUM ANALYZER , ENTER , 2. LEDs and fluorescent indicator tube are all turned on.
and DISC 1 simultaneously. Press DISC 2 button, and the key check mode is activated.
2. The fluorescent indicator tube becomes blank instantaneously, 3. In the key check mode, the fluorescent indicator tube displays
and the set is reset. “K 1 V0 J0”. Each time a button is pressed, “K”value in-
creases. However, once a button is pressed, it is no longer taken
[CD Delivery Mode] into account.
• This mode moves the pick-up to the position durable to vibra- “J” Value increases like 1, 2, 3 ... if rotating JOG knob in “+”
tion. Use this mode when returning the set to the customer after direction, or it decreases like 0, 9, 8 ... if rotating in “–” direc-
repair. tion.
Procedure: “V” Value increases like 1, 2, 3 ... if rotating VOLUME knob
1. Press POWER button to turn the set ON. in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “–
2. Press PLAY MODE button and POWER button simulta- ” direction.
neously. 4. To exit from this mode, press three buttons in the same man-
3. A message “LOCK” is displayed on the fluorescent indicator ner as step 1, or disconnect the power cord.
tube, and the CD delivery mode is set.

[MC Hot Reset]

• This mode resets the set with the preset data kept stored in the
memory. The hot reset mode functions same as if the power
cord is plugged in and out.
Procedure:
1. Press three buttons SPECTRUM ANALYZER , ENTER ,
and DISC 2 simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset.

[Sled Servo Mode]

• This mode can run the CD sled motor freely. Use this mode, for
instance, when cleaning the pick-up.
Procedure:
1. Select the function “CD”.
2. Press three buttons SPECTRUM ANALYZER , ENTER ,
and FUNCTION simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the
fluorescent indicator tube.
4. With the CD in stop status, press ) button in CD section
to move the pick-up to outside track, or 0 button to inside
track.
5. To exit from this mode, perform as follows:
1) Move the pick-up to the most inside track.
2) Press three buttons in the same manner as step 2.
Note:
• Always move the pick-up to most inside track when exiting from
this mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can
be chipped.

[Change-over of AM Tuner Step between 9kHz and 10kHz]

• A step of AM channels can be changed over between 9kHz and
10kHz.
Procedure:
1. Press POWER button to turn the set ON.
2. Select the function “TUNER”, and press TUNER/BAND
button to select the BAND “AM”.
3. Press POWER button to turn the set OFF.
4. Press ENTER/NEXT and POWER buttons simultaneously,
and the display of fluorescent indicator tube changes to “AM
9k STEP” or “AM 10k STEP”, and thus the channel step is
changed over.

– 30 –
[Aging Mode] 2-2. Operation during Aging Mode
This mode can be used for operation check of CD section and tape In the aging mode, the program is executed in the following se-
deck section. quence.
• If an error occurred: 1. A tape on FWD side is played for one minute.
The aging operation stops. 2. PAUSE STOP is made.
• If no error occurs: 3. Recording is made for 3 minutes. (For the deck not having
The aging operation continues repeatedly. the record function, the play is executed.)
4. FF is executed up to the end of tape.
1. Aging Mode in CD Section 5. A tape is reversed, and the tape on REV side is played for
1-1. Operating Method of Aging Mode one minute.
1. Set discs in DISC 1 and DISC 3 trays. 6. PAUSE STOP is made.
2. Select the function “CD”. 7. Recording is made for 3 minutes. (For the deck not hav-
3. Press three buttons SPECTRUM ANALYZER , ENTER ing the record function, the play is executed.)
, and KARAOKE PON/MPX simultaneously. 8. FF is executed up to the end of tape.
4. The aging mode is activated, if a roulette mark on the fluo- 9. Steps 1 through 8 are executed for the other deck.
rescent indicator tube is blinking. 10. Steps 1 through 9 are repeated unless an alarm occurred.
5. In the aging mode, the aging is executed in a sequence
given in “1-2. Operation during Aging Mode”. 2-3. Deck Selection Sequence
The aging continues unless an alarm occurred. • During the aging mode, decks are selected in the following se-
6. To exit from the aging mode, press POWER button to turn quence:
the set OFF. Deck A (FWD) → Deck A (REV)
• If a button other than buttons In CD section is pressed during ↑ ↓
aging, the aging in the CD section is finished. Deck B (REV) ← Deck B (FWD)
• To execute aging to the tape deck section successively, press ·
button in the deck A.
“AGING” is displayed on the fluorescent indicator tube. (For
the aging in tape deck, see “2. Aging Mode in Tape Deck Sec-
tion”.

1-2. Operation during aging Mode

In the aging mode, the program is executed in the following se-
quence.
1. The disc tray turns to select a disc. (For a disc selection
sequence, see Section 1-3.)
2. TOC of disc is read.
3. The pick-up accesses to the last track.
4. Steps 1 through 3 are repeated.

1-3. Disc Selection Sequence

• During the aging mode, discs are selected in the following se-
quence:
Disc 1 → Disc 3
↑ ↓
Disc 3 ← Disc 1

2. Aging Mode in Tape Deck Section

2-1. Operating Method of Aging Mode
1. Load a commercially available 10-minute tape into the
decks A and B respectively.
(If a 10-minute tape is not available, another tape may be
used but a cycle time will be longer.)
2. Select the function “TAPE”.
3. Rewind tapes in advance by pressing 0 button respec-
tively on decks A and B.
4. Press three buttons SPECTRUM ANALYZER , ENTER
, and KARAOKE PON/MPX simultaneously.
5. Press · button on deck A. (This button triggers the ag-
ing mode.)
6. The aging mode is activated if “AGING A” is displayed on
the fluorescent indicator tube.
7. In the aging mode, the aging is executed in a sequence
given in “2-2. Operation during Aging Mode”.
The aging continues unless an alarm occurred.
8. To exit from the aging mode, press POWER button to turn
the set OFF.

– 31 –
 SECTION 4 SECTION 5
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS
PRECAUTION DECK SECTION 0 dB=0.775 V
1. Clean the following parts with a denatured-alcohol-moistened
swab: 1. Demagnetize the record/playback head with a head demagne-
record/playback head pinch roller tizer. (Do not bring the head demagnetizer close to the erase
erase head rubber belts head.)
capstan idlers 2. Do not use a magnetized screwdriver for the adjustments.
2. Demagnetize the record/playback head with a head demagne- 3. After the adjustments, apply suitable locking compound to the
tizer. parts adjust.
3. Do not use a magnetized screwdriver for the adjustments. 4. The adjustments should be performed with the rated power
4. After the adjustments, apply suitable locking compound to the supply voltage unless otherwise noted.
parts adjusted. 5. The adjustments should be performed in the order given in
5. The adjustments should be performed with the rated power this service manual. (As a general rule, playback circuit ad-
supply voltage unless otherwise noted. justment should be completed before performing recording
circuit adjustment.)
• Torque Measurement 6. The adjustments should be performed for both L-CH and R-
Torque Torque Meter Meter Reading ch.
7. Switches and controls should be set as follows unless other-
36 to 61g•cm wise specified.
Forward CQ-102C
(0.50 – 0.84 oz•inch) 8. Set to test mode.
Forward 2 to 6g•cm (Press key switch same time SPECTRUM ANALYZER
CQ-102C
Back Tension (0.026 – 0.082 oz•inch) ENTER and EFFECT button.)
36 to 61g•cm
Reverse CQ-102RC • Test Tape
(0.50 – 0.84 oz•inch)
Reverse 2 to 6g•cm Tape Signal Used for
CQ-102RC
Back Tension (0.026 – 0.082 oz•inch) P-4-A100 10 kHz, –10 dB Azimuth Adjustment
61 to 143g•cm WS-48B 3 kHz, 0 dB Tape Speed Adjustment
FF, REW CQ-201B
(0.85 – 1.98 oz•inch)
P-4-L300 315 Hz, 0 dB Level Adjustment
• Tape Tension Measurement
Record/Playback Head Azimuth Adjustment
Torque Tension Meter Meter Reading
DECK A DECK B
Forward CQ-403A more than 100 g (3.52 oz)
Note: Perform this adjustments for both decks
Reverse CQ-403R more than 100 g (3.52 oz) Procedure:

test tape MAIN board

P-4-A100 CN207
(10KHz, –10dB) Pin 1 (L-CH)
Pin 3 (R-CH) level meter

set
+
–
MAIN board
CN207
Pin 2

– 32 –
1. Mode: Playback (FWD) Tape Speed Adjustment DECK A
2. Turn the adjustment screw and check output peaks. If the peaks Note: Start the Tape Speed adjustment as below after setting to
do not match for L-CH and R-CH, turn the adjustment screw the test mode.
so that outputs match within 1dB of peak. In the test mode, the tape speed is high during pressing the
H. SPEED DUBB button.
Procedure:
1. Turn the power switch on.
within 2. Press the SPECTRUM ANALYZER button, ENTER button
L-CH 1dB
peak and EFFECT button simultaneously.
within To exit from the test mode, press the POWER button.
output 1dB
level Mode: Playback (FWD)
test tape
R-CH WS-48B frequency counter
peak (3 kHz, 0 dB)
Screw Screw
position L-CH R-CH position +
peak peak set
–
3. Mode: Playback (FWD) MAIN board
CN207 (Pin 1 : L-CH)
test tape (Pin 3 :R-CH)
P-4-A100
(10kHz, –10dB) oscilloscope
pin 1 1. Insert the WS-48B into the deck A and the blank tape into the
L-CH
deck B.
pin 2
MAIN L 2. Press the REC button and · button on the deck B. Then
board V H
the deck B is at recording mode.
CN207
set R 3. Set the deck A to playback mode.
4. Keep pressing the H. SPEED DUBB button in playback mode.
R-CH
Then at HIGH speed mode.
pin 3
5. Adjust RV652 on the AUDIO board do that frequency counter
reads 6,000 ± 90 Hz.
waveform of oscilloscope
6. Take off the H. SPEED DUBB button.
Then at NORMAL speed mode.
7. Adjust RV651 on the AUDIO board so that frequency counter
in phase 45° 90° 135° 180°
reads 3,000 ± 90 Hz.
good wrong 8. Frequency difference between deck A and deck B the begin-
ning of the tape should be within ± 1.5%.
4. Repeat steps 1 to 3 in playback (REV) mode. Adjustment Location: AUDIO board
5. After the adjustments, apply suitable locking compound to the
pats adjusted. Sample Value of Wow and flutter: 0.3% or less W.RMS (WS-48B)
Adjustment Location: Record/Playback Head (Deck A and B)
and MAIN board. Playback level Adjustment DECK A DECK B
Procedure:
Mode: Playback (FWD)

test tape
P-4-L300 level meter
(315 Hz, 0 dB)

set +
–
reverse
MAIN board
CN207 (Pin 1 : L-CH)
(Pin 3 : R-CH)

Deck A is RV311 (L-CH) and RV411 (R-CH), Deck B is RV301 (L-

CH) and RV401 (R-CH) so that adjustment within adjustment level
as follows.
Adjustment Level:
CN207 PB level: 301.5 to 338.3 mV (–8.2 to –7.2 dB) level
forward difference between the channels: within ±0.5 dB
Adjustment Location: AUDIO and MAIN boards

– 33 –
Record bias Current Adjustment DECK B Adjustment Location:
Procedure: [MAIN BOARD] (Component Side)
1. Mode: Record
RV1501
Pin 6 (L-CH) of IC1501 on the MAIN board.
Pin #¶ (R-CH) of IC1501 on the MAIN board. 1 IC1501
3
1) 315 Hz  CN207 CN205
2) 10 kHz  50 mV (–23.8 dB) IC301
 IC201 RV1551
AF OSC blank tape
600 Ω CN-123 Record Level
attenuator Adjustment
set

Pin 2 (GND) of ICN207 on the MAIN board.

2. Mode: Playback
recorded level meter
portion [AUDIO BOARD] (Conductor Side)

+ Record Bias Current

set Tape Speed Adjustment
– Adjustment


















R L (NORMAL) (HIGH)
CN207 (Pin 1 : L-CH) RV301®L
(Pin 3 : R-CH) RV651 RV652
RV401®R RV441 RV341
® ®




 
Confirm playback the signal recorded in step 1 become adjustable  RV311
Playback Level
limits as follows. Adjustment
Playback Level  L®

If these levels do not adjustable limits, adjustment the RV341 (L- Adjustment RV411
– DECK B – 
CH) and RV441 (R-CH) on the AUDIO board to repeat steps 1 and R®
2. – DECK A –
Adjustable limits: Playback output of 315 Hz to playback output
of 10kHz: 0±0.5 dB
Adjustment Location: AUDIO and MAIN boards

Record Level Adjustment DECK B

Pin 6 (L-CH) of IC1501 on the MAIN board.

Pin #¶ (R-CH) of IC1501 on the MAIN board.
315 Hz, 50 mV (–23.8 dB)
AF OSC
blank tape
600 Ω CS-123
attenuator
set

Pin 2 (GND) of CN207 on the MAIN board.

Procedure:
recorded level meter
portion

set +
–

CN207 (Pin 1 : L-CH)

(Pin 3 : R-CH)
1. Mode: Record
2. Mode: Playback
Confirm playback the signal recorded in step 1 become adjustable
limits as follows.
If these levels do not adjustable limits, adjustment the RV1501
(L-CH) and RV1551 (R-CH) on the MAIN board to repeat steps 1
and 2.
Adjustable limits:
CN207 PB level: 47.3 to 53.1 mV (–24.3 to –23.3 dB)
Adjustment Location: MAIN board

– 34 –
 TUNER SECTION 0dB=1µV

Note: As a front-end (FE1) is difficult to repair if faulty, replace

it with new one.

AM Section Adjustment
Setting:

loop antenna
loop antenna (Supplied accessories)

AM RF SSG

set

30% amplitude
modulation by
400 Hz signal 60 cm AM ANTENNA
terminal (TM1)
Field strength dB (µV/m) =SSG output level dB (µV/m) –26 dB.
AM Tuned Level Adjustment
Band: AM
Procedure:
Adjustment Location:
1. Set the output of SSG so that the input level of the set be-
comes 55 dB. [TCB BOARD] (Component Side)
2. Tune the set to 999 kHz.
3. Adjust RV42 to the point (moment) when the TUNED indica- IC2
tor will change from going off to going on. RV42
AM Tuned
RV41 Level
Adjustment Location : TCB board FM Tuned Level Adjustment
Adjustment
FM Section Adjustment
Note: This adjustment should be performed after the AM Tuned
Level Adjustment due to the same adjustment element. TM1
Setting:

FM RF stereo signal FE1

generator
75 Ω coaxial

set
Carrier frequency : 98 MHz
Modulation : AUDIO 1 kH, 75 kHz
deviation (100%) FM ANTENNA terminal
(TM1) (75 Ω open)

FM Tuned Level Adjustment

Band: FM
Procedure:
1. Supply a 25dBµ 98 MHz signal from the ANTENNA termi-
nal.
2. Tune the set to 98 MHz.
3. If the TUNED indicator does not light, adjust RV41 to the
point (moment) when the TUNED indicator will change from
going off to going on.
Adjustment Location: TCB board

– 35 –
 CD SECTION S Curve Check
Note: oscilloscope
1. CD Block is basically designed to operate without adjustment. BD board
Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. TP (FEO) +
3. Use an oscilloscope with more than 10M impedance. TP (VC) –
4. Clean the object lens by an applicator with neutral detergent
Procedure:
when the signal level is low than specified value with the fol-
1. Connect oscilloscope to test point TP (FEO).
lowing checks.
2. Connect between test point TP (FOK) and GND by lead wire.
3. Turn Power switch on.
Focus Bias check
oscilloscope 4. Put disc (YEDS-18) in and turned Power switch on again and
actuate the focus search. (actuate the focus search when disc
BD board table is moving in and out.)
TP (FEO) + 5. Check the oscilloscope waveform (S-curve) is symmetrical
TP (VC) – between A and B. And confirm peak to peak level within 3±1
Vp-p.
Procedure: S-curve waveform
symmetry
1. Connect oscilloscope to test point TP (RF). (GND terminal :
VC)
2. Turned Power switch on. A
3. Put disc (YEDS-18) in and playback. within 3 ± 1 Vp-p
4. Confirm that the shape “≈” can be clearly distinguished at the B
center of the waveform and check the RF signal level.

• RF signal 6. After check, remove the lead wire connected in step 2.

VOLT/DIV: 200 mV Note: • Try to measure several times to make sure than the ratio
TIME/DIV: 500 ns of A : B or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the
brightness to obtain best waveform.
level:
1.3 ± 0.3 Vp-p
RF Level Check
oscilloscope
BD board

TP (RF) +
TP (VC) –

Procedure:
1. Connect oscilloscope to test point TP (RF) on BD board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that oscilloscope waveform is clear and check RF sig-
nal level is correct or not.
• RF signal
VOLT/DIV: 200 mV
TIME/DIV: 500 ns

level:
1.3 ± 0.3 Vp-p

Note:
Clear RF signal waveform means that the shape “≈” can be
clearly distinguished at the center of the waveform.

– 36 –
E-F Balance (1 Track Jump) check Adjustment Location:
(Without remote commander)
[BD BOARD] (Conductor Side)
oscilloscope
BD board
RF
TP (TEO) + VC
TP (VC) – FOK

CNU101
Procedure: IC
IC101
1. Connect oscilloscope to test point TP (TEO) on BD board. I02
2. Turned Power switch on.
3. Put disc (YEDS-18) in to play the number five track.
TEO
4. Press the “P (Pause)” button. (Becomes the 1 track jump
mode) FEO
GND
5. Check the level B of the oscilloscope's waveform and the A
(DC voltage) of the center of the Traverse waveform.
Confirm the following:
IC103
A–B × 100 = ±7 (%)
2 (A + B)
1 track jump waveform
Center of the waveform

B CNU102

A (DC voltage)
0V

symmetry
level : 500 mV ± 100 mVp-p

– 37 –
 SECTION 6
DIAGRAMS
• Circuit Board Location

TRANS board

PANEL board TCB board

KEY CON board

MAIN board

HEADPHONE-MIC
board

TC-A SW
board
POWERAMP
board

LED board

CD-A SW board TC-B SW board

CD-B1 SW board
DOOR SW board
CD-B2 SW board

MOTOR board

LEAF SWITCH
board

CD MOTOR board

BD board

AUDIO board

TABLE SENSOR board BD LED board

– 38 –
• Waveforms
— BD Section—
1 IC101 #£ pin (PLAY MODE) 6 IC103 ^™ pin (RFCK) !¡ IC301 !£ pin (XT2)

Approx. 1.3 Vp-p

5.6 V 4.6 Vp-p

135.5 µsec 31.3 µsec

2 IC101 2 pin (FEI) (PLAY MODE) 7 IC103 &¢ pin (WFCK) — TUNER Section—
!™ IC1 @¢ pin (XOUT)

Approx. 0.1 V 5.6 V

4.8 Vp-p

135.5 µsec

3 IC101 $¶ pin (TEI) (PLAY MODE) 8 IC103 *ª pin (XTAI)

222 nsec

!£ IC2 @£ pin (VCO)

Approx. 0.2 V 10 V

4.8 Vp-p

59.8 nsec

4 IC103 @¶ pin (MDP)

— PANEL Section— 2.2 nsec
9 IC601 !¤ pin (X-OUT)

2.4 V

4.3 V

7.8 µsec

125 nsec
5 IC103 ^º pin (XPCK)
— MAIN Section—
0 IC301 0 pin (X2)

7V

5.7 V

230 nsec

200 nsec

– 39 –
 HCD-XB6K

6-1. BLOCK DIAGRAMS

– TUNER SECTION –

ST +10V

Q5 22 MPX IN AMP OUT L 16

TM1 FE1 AM / FM 24
ANTENNA FM FRONT END CF1 CF2
10.7MHz OUT L 20 LPF 18 AMP IN L
IF AMP IF AMP 10.7MHz
FM 75Ω ANT IN IF OUT 1 FM IN
Q1,2 Q3,4
F OUT

OUT R 21 RCH
VT

A
AM MAIN SECTION
(page 43)
IC2
FM / AM MPX

STEREO 70
4 REG ST LED 8
TUNED 69
TUNED 7

AM MIX 2 AM IF 5 AM IF
IFT41

AM
FE2 SD 12
AM FRONTEND
7 RV42
B+ AM
TUNED
F OUT 9 29 AM OSC LEVEL
3 ANT IN
9 DET
X42
RF OUT 13 27 AM RF IN 10.7MHz
AM 13
VCO STOP

SD
AM / FM

X43
IF BUFF
FM SD

MUTE

450KHz
VT 23 VCO
14 X41
30 14 15 11
456KHz

RV41
FM
TUNED MUTE 72
LEVEL B
MAIN
SECTION
(page 44)

X21
4.5MHz

10 15 19 14 7 2 12 8 1 24
ST-CE 68
X OUT
FM

X IN
PD1
FM OSC

VCO STOP
AM OSC

IF REQ
FM

IF

CE 3
COM-DIN 67
DI 4
PLL
IC1 COM-CLK 65
CL 5
COM-DATA 66
DO 6

• R CH:Same as L CH
• SIGNAL PATH
:FM

:AM

– 40 –
– CD SECTION – – DECK SECTION –

RV311 MAIN
IC611 REC REC
PB LEVEL 6 F SECTION
PBEQ 70 (page 43)
DOL
3 1 2 DOLBY PB
AMP MAIN
HP101 B 8 G
PB SECTION
PLAYBACK HEAD (page 43)
OPTICAL PICK-UP BLOCK 120 PAS
X101 (A DECK) R-CH IC601 4
IC101(1/2) 16.9344MHz
PBEQ RV301
FOCUS/TRACKING 5 7
B+ AMP PB LEVEL
DETECTOR K /SLED/SERVO IC602
RF AMP PB / REC SW
89 90 HRPE101
E RV105 9
1
1 38 PD1 RFO 33 44 RF REC LEVEL
A 35 PB R-CH
4 MAIN REC/PB HEAD
C,OUT 24 14 CNIN LOUT1 86 E SECTION (B DECK) 2 10 IC1501
2 39 PD2 4
A D SENS1 25 13 SEIN (page 43) R-CH HEAD AMP 37 REC R-CH
D IC103
5 DECK PROCES
FOK 27 23 FOK DIGITAL SIGNAL
B C 10 41 F PROCESSOR R-CH 3
C DATA 22 15 DATAO C331,L331
6 42 E ERASE RV341
XLT 21 16 XLTO (HEAD) X BIAS REC
LOUT2 93 R-CH REC BIAS 11
B CLK 20 17 CLKO TRAP EQ
LOCK 19 29 LOCK Q621,622

NORM/CROM/METAL
F BIAS OSC

CLOCK
FE-O 6 T621

SPOD

SCOR

SQCK
XRST

SENS
SQS0
DATA
XLAT
MDP
NORM
25

REC/PB/PASS
FE-M 7 Q623 BIAS

BIAS ON/OFF
NORM/HIGH

RM ON/OFF

LM ON/OFF
NR ON/OFF
21 27 75 100 12 11 10 9 8 7 SWITCH 24 SW

A120/170
CROM

PB A/B
TA-M 12

57

47
74
18

48
58

34
36
TA-O 13 S101 +7V 22
LIMIT SWITCH
12 13 14 15 16 17 18 19 20
Q101 36 LD S1005
LD DRIVE 73 MAIN
XRST SENS2 26 C SECTION A CrO2
37 PD (page 43)
LASER S1008
DIODE B CrO2

96
23

87

88

89
90
91
92
93
Q1531,Q1532 MAIN
H
CAPSTAN MOTOR SECTION
FOCUS TRACKING 9 (page 43)
COIL COIL SWITCH 86
MUTE
T- RV652
15 TRACKING M1 B+
COIL DRIVE 27 HIGH SPEED
16 CAPSTAN M (+12V)
MOTOR Q651
Q1533
FOCUS / TRAKING CAPSTAN MOTOR
T+ SWITCH 82
COIL DRIVE RV651 CONTROL
IC102 (1 / 2 ) NORMAL SPEED
2-AXIS
DEVICE Q1534,Q1535
F- IC1502 85
18 FOCUS 2 4 SWITCH
26 M2 TRIGGER
F+ COIL DRIVE
17 TRIGGER M MOTOR 5 83
MOTOR 10 DRIVE 61
84
S1001
A PLAY
SLED / SPINDLE 94
MOTOR DRIVE SLED
IC102 (2 / 2) SERVO S1002 95
IC101 (2 / 2)
B PLAY
M102 S1004
12
SLED MOTOR M . SLED MOTOR
DRIVE
6 16 SLO SL-P 14 (A HALF) 97
11
S1007
(B HALF)
M101 14 28
SPINDLE MOTOR M .
13
SPINDLE MOTOR 3
S1006
DRIVE MAIN
(REC A) +5V I
SECTION
S1009 (page 43) • R CH : Same as L CH
(REC B) • SIGNAL PATH
77 :PB (DECK A)
S201 MAIN
UP SWITCH D SECTION
:PB (DECK B)
(page 43)
:REC (DECK B)
IC202 76
DISC TABLE
SENSOR

Q201 62
SWITCH • R CH:Same as L CH
• SIGNAL PATH
61 :CD
3 IC201 1
M201
TABLE MOTOR
M 7
MOTOR
9
60
DRIVE

– 41 – – 42 –
– MAIN SECTION –

IC231
SPEANA MIX R-CH
J760
2
+ PHONES
J101 (1 / 2) IC101 – 1
PHONO 3
PHONO AMP + L-CH
IC102 INPUT SELECTOR IC801
65 64 POWER AMP
DECK SECTION 15 TM131
(page 42) G 69 -
+ RY141 SPEAKER
CD SECTION E 14 13 71 45 44 43 42 38 3 +
(page 41) – 12 -
A 4 – Q801
28 R-CH
TUNER SECTION A 11 B MICON EQ Q204 OVER LOAD
(page 40) 29 INTERFACE + R-CH
R-CH 19 + DET R-CH

BUF IN1
C IC201 MUTE
J101 (2 / 2) 12 3 R-CH 30 15 R-CH

BB22

BB12
EQUALIZER/VOLUME 20 –
VIDEO (AUDIO) MUTE Q851
A
4 10 8 OVER LOAD
B 32 33 34 62 39 40 41 Q231
R-CH 5 9 DET
SWITCH + L-CH
2 C
6
Q283
Q232 MUTE Q282 - TM132
Q201 Q202 Q203 Q141,Q142
SWITCH OVER LOAD SORROUND
DECK SECTION F SWITCH DBFB SWITCH FEED BACK RELAY DRIVE
DET -
(page 42)

99
45
44

2
3
R-CH + R-CH
2 1 4
Q281 IC281
7
SWITCH PROTECTOR
IC502 6
MULTIPLEXER

5 4

22 LPF1 IN MPX OUT 15 3

44
45
99

3
2
20 HPF IN 14 R-CH
STORE BE 9

44
45

4
5
9
TUNER B

87
88
89
90
91
92
93
96

55
56
+5V 14 VCC DATA 7 CD SECTION C
Q502 (page 41) SECTION
(page 40)

18
34
36
47
48
57
58

73
74
IC501 SWITCH

65
66
67
68
69
70
72
KEY CONTRTOL
Q501 18 34 36 47 48 57 58 73 74 99 2 87 88 89 90 91 92 93 96 3 44 45 4 5 65 66 67 68 69 70 72 55 56 100 6 1
SWITCH

SCOR
SQ-DATA-IN
SQCLK
CD DATA
CD CLOCK
XRST
XLT

SENS2
SENS

SW-F-CON
DBFB H/L

PB A/B
EQ-H/N
BIAS
REC-MUTE
NR ON/OFF
R/P-PASS
TC-MUTE
REALY

427LAT

COM DOUT
COM CLK

KEY-CON LAT
KEY-CON ON

ST-CLK
ST-DIN
ST-DOUT
ST-CE
TUNED
STEREO
ST MUTE

11C-DATA
11C-CLK

STK MUTE

F-RELAY

TA MUTE
45

44
4

IC301

CD-POWER
CAP-M-ON/OFF
RV761 MAIN CONTROL

A-SHUT

B-SHUT

POWER

AC CUT
A HALF

B HALF

RESET
A-PLAY-SW
B-PLAY-SW
IC761 ECHO LEVEL

TRAY-LED

TRG-LOW

XT2

XT1
CAP-H/N

X2

X1
J762

T-SENS
UP SW

B-TRG
A-TRG
TBL-R
TBL-L
MIC2 1 8 97 28 26 27 46 10 11 13 14 98 15 20

KEY CONTROL 77 76 62 61 60 86 85 84 83 82 94 95
X301 X302

77
76

62
61
60
RV706 Q301
IC760 (1 / 2) IC760 (2 / 2) 5MHz 32.768KHz
MIC AMP MIC LEVEL MIC AMP SWITCH
CD SECTION D Q1001 Q1002
Q901 Q901
J761 (page 41) REEL REEL
Q902 Q902
MIC1 DET DET
SWITCH SWITCH

86
85
84
83
82

94
95

97

28
DECK SECTION I IC302
(page 42) Q907 Q905 RESET
SWITCH Q906
SWITCH
H +5V
55
56

DECK
SECTION (page 42)
S691
LED DRIVE DOOR SW
S601-S607,S609-S625 AMS VOLUME
D611-D625 S627-S634 OPEN
Q604-Q608
D628 Q609-Q611 S641-S647,S651-S659 JOG § ROTARY
D631,D632 S661-S668,S676-S679 S711 ENCODER +35V D901
Q613-Q615
D635-D638 Q617-Q619 S681-S686 S701 -35V RECT
D641 Q621,Q622
D645-D647 • R CH : Same as L CH
+7V IC901 T901 • SIGNAL PATH
3-10 • 15-16 • 18-23 • 25 • 47 33 - 37 26 • 41 38 24 40
-7V REG POWER TRANSFORMER
LED KEY1-KEY5 JOG A•B
DOOR SW

VOL-A

VOL-B
AC -IN :FM
SELECT SWITCH D902
Q601-Q603 29 LED SELECT
IC601 IC902 |
CD MOTOR +7V :PB
DISPLAY CONTROL REG D905
27 CLOCK RECT :REC (DECK B)
SPEANA4
SPEANA3
SPEANA2
SPEANA1

IC903
V-LOAD

28 DATA +5V
RESET
SIRCS
X OUT

REG :CD
X IN

GR1-GR16 SEG1-SEG35 D906

Q903 IC904 S901
51- 66 67-100 • 1 2 12 13 45 44 43 42 39 14 ST +10V
REG REG
D907 VOLTAGE • Abbreviation
RECT SELECTOR : Saudi arabia model
TC MOTOR EA
IC602 +12V SP : Singapore model
VP Q904 E,EA,SP,IA
SIRCS VP IA : Indonesia model
BACK LIGHT REG
FL601 X601
VF F1 VF
VF 8MHz LOW FREQ
FRUORESCENT INDICATOR TUBE
-7V +7V F2
HIGH FREQ
D671-D674 F3
F4

– 43 – – 44 –
• IC Block Diagrams –BD Section –

IC101 CXA1992AR

RF_M

RF_O
RFTC

RF_I
PD2

PD1

CC1

CC2

FOK
PD

LD

CP

CB
39 38 37 36 35 34 33 32 31 30 29 28 27
VEE

–
+
–
+

–
+

–
+
RF SUMMING
PD2 IV PD1 IV

–
+
AMP
AMP AMP

–
+
+
–
FE_BIAS 40 26 SENS2

–
+
VCC +

+
–
APC –

VEE IIL
F 41 – ↓ 25 SENS1
+ LASER POWER CONTROL
TTL
F IV AMP VCC

–
+

+
–
+
VCC FE AMP VCC
E 42 – 24 C. OUT

–
+

–
+
+
E IV AMP
VEE

–
+

+
–
DFCT
–
+

EI 43 23 XRST

–
+
IFB4
IFB5
IFB2
IFB3

IFB6
IFB1
BAL1
BAL2
BAL3
BAL4

+
VEE

–
+
–
LEVEL S
VEE
TGFL

VEE
VEE 44 VEE 22 DATA
TOG4
TOG3
TOG2
TOG1

FO. BIAS

–
–

+
+
WINDOW VCC
–
+

MIRR IIL
+ COMP. ↓
–
+
– TTL TTL
TEO 45 + TRK. GAIN FOK ↓ 21 XLT
– WINDOW COMP. IIL
+ +
– –

DFCT1
LDON

E-F BALANCE

MIRR
LPCL

TGFL
LPC

CC1
LPFI 46 + WINDOW COMP. 20 CLK
+
– FOH
–
FOL
TGH
TGL IIL DATA REGISTER
TEI 47 19 LOCK
BALH INPUT SHIFT REGISTER
– ADDRESS DECODER
+ BALL
SENS SELECTOR
ATSC
OUTPUT DECODER
TZC
ATSC 48 – FZC VCC 18 VCC
+
ATSC
WINDOW
COMP.
DFCTO IFB1-6 FS1-4 TG1-2 TM1-7 PS1-4
TZC 49 – BAL1-4 ISET 17 ISET
+ TOG1-4
DFCT
TZC COMP.
TM1
VCC VCC
TDFCT 50 TRACKING 16 SL_O
VCC TG1 PHASE COMPENSATION
TM4 TM6

+
VC 51 – 15 SL_M
VCC
TM7
VCC VEE
FOCUS FS1 TM5
PHASE COMPENSATION TM3 –
FZC 52 + + 14 SL_P
–
VEE VEE
+ FS2 TM2
DFCT – Charge
up FSET
FZC COMP.
TG2
–

FS4
+

VEE
1 2 3 4 5 6 7 8 9 10 11 12 13
FEO

FEI

FDFCT

FGD

FLB

FE_O

FE_M

SRCH

TGU

TG2

FSET

TA_M

TA_O

– 83 –
 IC102 BA5941FP

OP IN (–)

OP IN (+)
OP OUT

OUT3A

OUT3B

OUT4A

OUT4B
IN4B

IN4A

IN3B

IN3A

GND

VCC
NC
28 27 26 25 24 23 22 21 20 19 18 17 16 15
NC
– +
Vcc + – + – + – + –

–
+ LEVEL SHIFT
–
+ LEVEL SHIFT

+
LEVEL SHIFT
–
+
LEVEL SHIFT
–

– + + – – + + –
Vcc MUTE Vcc

1 2 3 4 5 6 7 8 9 10 11 12 13 14
VCC

BIAS IN

IN1B

IN1A

IN2B

IN2A

GND

GND

MUTE

VCC

OUT2A

OUT2B

OUT1A

OUT1B
IC103 CXD2519Q
PCMDI
EMPHI

PCMD
LRCKI
SYSM

EMPH
WFCK

MNT0
MNT1
MNT3
SCOR

DOUT
SBSO

GTOP
XPCK
XROF
C2PO

XUGF
EXCK

RFCK
XTSL
FSTT

BCKI
C4M
VDD

VDD
VSS

VSS

BCK
GFS

80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51

NC 81 50 LRCK
AVSS 82 49 WDCK
AVDD 83 48 ASYE
AOUT1 84 47 ASYO
– ASYMMETRY
AIN1 85 46 ASYI
– CORRECTOR
PWM

+
3RD-ORDER NOISE SHAPER

LOUT1 86 + 45 BIAS
AVSS 87 44 RF
ERROR
XVDD 88 CORRECTOR 43 AVDD
D/A
XTAI 89 EFM INTERFACE 42 CLTV
DEMODURATOR DIGITAL
XTAO 90 – 41 AVSS
PLL
PWM

XVSS 91 – + 40 FILI
+
AVSS 92 16K RAM DIGITAL OUT 39 FILO
LOUT2 93 38 PCO
AIN2 94 OSC 37 VCTL
AOUT2 95 36 V16M
AVDD 96 35 VCKI
SERIAL-IN OVER SAMPLING SUB CODE
CLOCK
AVSS 97 INTERFACE DIGITAL FILTER PROCESSOR 34 VPCO1
GENERATOR
NC 98 33 VPCO2
NC 99 TIMING SERVO 32 TES1
LOGIC CPU
XRST 100 AUTO DIGITAL CLV 31 TES0
INTERFACE
SEQUENCER

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
VDD
VSS
LMUT
RMUT
TES2
CKOUT
SQCK
SQSO
SENS
DATA
XLAT
CLOK
SEIN
CNIN
DATO
XLTO
CLKO
SPOA
SPOB
SPOC
SPOD
XLON
FOK
VDD
VSS
MON
MDP
MDS
LOCK
PWMI

– 84 –
– CD MOTOR Section –

IC201 TA8409S

VREF
STANDBY BLOCK
BLOCK

HEAT
CUT OFF
BLOCK

1 2 3 4 5 6 7 8 9
IN2 VCC OUT2 NC GND VS OUT1 VREF IN1

– TUNER Section –

IC1 LC72130
AOUT2

AOUT1
XOUT

AMIN
FMIN
AIN2

AIN1

VDD
VSS

PD2

PD1

IO2

24 23 22 21 20 19 18 17 16 15 14 13

PHASE DETECTOR
CHARGE PUMP

UNLOCK POWER
DETECTOR ON 1/2
RESET
REFERENCE SWALLOW COUNTER
DIVIDER 1/16, 1/17 4BITS

12BITS PROGRAMMABLE
DRIVER

C 2B UNIVERSAL
I/F DATA SHIFT REGISTER LATCH
COUNTER

1 2 3 4 5 6 7 8 9 10 11 12
XIN
BO5
CE
D1
CL
D0

BO1

BO2

BO3

BO4

IO1

IFIN

– 85 –
IC2 LA1835

AMP-IN R
AM-RF-IN

AMP-IN L
AM. CUT
AM-OSC

FM-AFC

MPX-IN
AM/FM
FM-SD

OUT R

OUT L
AGC

VCO

R
L
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16

ALC AM AM AM DECODER
OSC MIX RF. AMP ANTI BIRDIE
BUFF
STEREO
AGC SW
S METER STEREO
DRIVE
TRIG MUTE
FM AM
IF DET FF FF FF

AM/FM VCO
PILOT
LEVEL IF COMP DET
S-CURVE BUFF
DET AM/FM PHASE
TUNING SW DET
FM FM DRIVE AM
IF DET
FM
REG GND VCC

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
FM-IN

AM-MIX
IF

REG
AM-IF

GND

TU-LED

ST-LED

DET

VCC

IF-BUFF

AM. SD

AM. SD

AM/FM

VCO-STOP

– DECK Section –

IC602 µPC1330HA

INVERTER

COMPARATER

1 2 3 4 5 6 7 8 9
SW R1 GND SW P1 CONT GND VCC SW P2 GND SW R2

IC1502 LB1641

T.S.D O.C.P

MOTOR MOTOR
DRIVE DRIVE

FWD/REV/STOP
CONTROL LOGIC

1 2 3 4 5 6 7 8 9 10
FILTER
MOTOR
GND

FILTER

CLAMP

FWD.IN

REV.IN

VCC 1

VCC 2

MOTOR
NOISE
NOISE
DRIVE

DRIVE

– 86 –
– MAIN Section –

IC102 MC14052BCP

16 13 10 3 6 7 8
VDD SELECT A INH 7 VEE VSS

0 1 2 3 SELECT B 0 1 2 3
12 14 15 11 9 1 5 2 4

IC201 M6247FP

VOL OUT2
KEY OUT2

VOL IN2
REC 2A

REC 2B

REC 2C

F OUT2
F1 IN2

F2 IN2

F3 IN2

F4 IN2

BBIN2
F1 O2

F2 O2

F3 O2

F4 O2
F1 F2

F2 F2

F3 F2

F4 F2

F5 F2

BB12
NC7

NC6

64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41

KEY IN2 65 SBAND GRAPHIC EQUALIZER 40 BB22

–
BPF OUT 66 + 39 BUF IN1
+
–
BPF IN 67 38 BUF OUT1

NC8 68 37 NC5

–
+
IN 2B 69 + 36 AVDD
+ +
–
NC9 70 – – 35 DGND

IN 2A 71 – 34 LATCH
U-CON
+
AVSS 72 – – INTER 33 DATA
+ + FACE
AGND 73 32 CLOCK

IN 1A 74 31 DVDD

NC1 75 – – 30 PORT C
+ +
+
IN 1B 76 – 29 PORT B
+
–

NC2 77 28 PORT A

DELAY IN 78 – 27 BUFOUT1
+
– +
DELAY OUT 79 26 BUFIN1

KEY IN1 80 SBAND GRAPHIC EQUALIZER 25 BB21

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
REC 1A

REC 1C
KEY OUT1

NC3

REC 1B

NC4

F1 F1

F1 O1

F2 F1

F2 O1

F2 IN1

F3 F1

F3 O1

F3 IN1

F4 F1

F4 O1

F4 IN1

F5 F1

F OUT1

VOL IN1

VOL OUT1

BBIN1
F1 IN1

BB11

IC281 µPC1237HA

OVER LOAD DET

VCC ON
F/F MUTE
OFFSET DET

LATCH/
AUTORESET

AC OFF
DET

VCC
1 2 3 4 5 6 7 8

– 87 –
IC501 M65847FP-TP 26 DAIINTOUT
– PANEL Section –

IC761 M65850P
24 ADINTOUT

21 LPF1OUT

17 LPF2OUT
25 DAIINTIN

23 ADINTIN

19 HPFOUT

15 MIXOUT
28 MODE2

27 MODE1

22 LPF1IN

18 LPF2IN
20 HPFIN

16 MIXIN

LPF2OUT
OP2OUT
LPF2IN
CLOCK

OP2IN
VCC

REF
14 13 12 11 10 9 8
– – – –
A/D +

+
OSCILLATOR
LPF1 HPF LPF2 MIX D/A LPF2
REF REF REF REF
1/2 VCC

CLOCK CLOCK DO1

RESET RAM MO
GENERATOR AUTO MAIN 20KBIT
RESET
RESET CONTROL SRAM
D/A REF MI
LOGIC D1 DO0

A/D
1 2 3 4 5 6 7 8 9 10 11 12 13 14 LPF1
ADCONT

DA1CONT

DA2CONT

KEY DOWN

KEY UP

CLKO/KEY0

SDATA/KEY1

SCK/KEY2

STROBE/KEY3

KEY4

KEY5

REF

GND

VCC
1 2 3 4 5 6 7

LPF1IN

LPF1OUT

OP1OUT
OP1IN
CC1

CC2

GND
IC502 MC14053BCP

B1 1 16 VDD

B0 2 15 B.COM
OPEN
C1 3 14 A.COM

C.COM 4 13 A1
OPEN
CO 5 12 A0

INH 6 11 A

VEE 7 10 B
OPEN

VSS 8 9 C

IC901 LA5617

CURRENT CURRENT START

ON/OFF ON/OFF
LIMITER LIMITER CIRCUIT
COMPARATER

VMUTE VCC VREF

~140uA

OVER HEAT
VREF VCC PROTECT
_

ERROR VREF
AMP ~_1.8V
ERROR
AMP

1 2 3 4 5 6 7 8 9 10
VO1

VCC

CN1
EN

EN DISPLAY

GND

NC

CN2

VEE

VO2

– 88 –
6-18. IC PIN FUNCTION DESCRIPTION
MAIN BOARD IC301 µPD780018Y (MAIN CONTROL)

Pin No. Pin Name I/O Function

1 TA-MUTE O Line mute signal output
2 DBFB-H/L O DBFB H/L select signal output
3 427-LT O Latch signal output for IC201 (62427)
4 KCON-LT O Latch signal output for IC501 (Key Control)
5 KCON-ON/OFF O Key control ON/OFF signal output
6 F-RELAY O Front speaker relay control output
7 R-RELAY O
Not used
8 PL-RELAY O
9 TEST I Connected ground
10 X2 O
X’tal (5MHz)
11 X1 I
12 VDD – Power supply (+5V)
13 XT2 O
X’tal (32.768 KHz)
14 XT1 I
15 RESET I Reset signal input
16 INT/IN I
Connected ground
17 INT/IN/OUT I
18 SCOR O Subcode data request signal output
19 SOFT-TEST O Software test port
20 AC-CUT I Back up signal input
21 RDS-INT I
Not used
22 RDS-DATA I
23 VDD – Power supply (+5V)
24 AVDD I Analog reference voltage input
25 ADJ I CD adjust point port
26 A-SHUT I A Deck reel pulse detector
27 B-SHUT I B Deck reel pulse detector
28 B-HALF I Half detector signal input
29 CLK-CHECK I Connected ground
30 SPEC-IN I Version select signal input
31 ADJ 2 I Connected ground
32 DEMO-MODE I Connected ground
33 AVss – Ground
34 SQ-DATA-IN I Subcode Q data input
35 — – Not used
36 SQ-CLK I Subcode Q data clock input
37 SW-ON/OFF O Not used
38, 39 FUNC 1, 2 I Connected ground
40 Vss – Ground
41 VOL-LAT O
Not used
42 PL-LAT O
43 COM-DIN I Connected ground
44 COM-DOUT O Common serial data output

– 89 –
Pin No. Pin Name I/O Function
45 COM-CLK O Common serial clock output
46 CD-POWER O CD power on signal output
47 CD-DATA O CD data output
48 CD-CLOK O CD clock output
49 MSM-CMD O Not used
50 MSM-BUSY I Connected ground
51 MSM-LT O
52 MSM-NAR I Not used
53 MSM-CH O
54 INPUT-CHANGE O Not used
55 11C-DATA O Data output for IC601
56 11C-CLK O Clock output for IC601
57 XRST O CD reset signal output
58 XLT O CD latch signal output
59 FOUCUS-SW O Not used
60 TBL-L O
Table motor control output
61 TBL-R O
62 TRAY-LED O CD tray LED ON/OFF output
63 LOAD-OUT O
Not used
64 LOAD-IN O
65 ST-CLK O Tuner clock output
66 ST-DIN I Tuner data input
67 ST-DOUT O Tuner data output
68 ST-CE O Tuner chip enable output
69 TUNED I Tuned detection for tuner
70 STEREO I Stereo detection for tuner
71 Vss – Ground
72 ST-MUTE O Tuner mute signal output
73 SENS2 I
BD Condition signal input
74 SENS I
75 DISC-SENS I Not used
76 T-SENS I CD table detection signal input
77 UP-SW I Up SW (S201) signal input
78 ENC 3 I
79 ENC 2 I Not used
80 ENC 1 I
81 OUT-OPEN I Not used
82 CAP-M-H/N O Capstan motor H/N speed select signal output
83 B-TRG O Trigger motor control output
84 A-TRG O Trigger motor control output
85 TRG-LOW O Trigger motor control output
86 CAP-M-ON/OFF O Capstan motor ON/OFF signal output
87 PB-A/B O PB Deck A/Deck B select output

– 90 –
Pin No. Pin Name I/O Function
88 EQ-H/N O Equalizer H/N select output
89 BIAS O Bias ON/OFF signal output
90 REC-MUTE O REC mute ON/OFF selection output
91 NR-ON/OFF O NR ON/OFF signal output
92 R/P-PASS O REC/PB/PASS selection output
93 TC-MUTE O TC mute ON/OFF selection output
94 A-PLAY-SW I Deck A play detect
95 B-PLAY-SW I Deck B play detect
96 TC-RELAY O REC/PB head selection output for IC602
97 A-HALF I Deck A cassette detect
98 POWER O POWER ON/OFF signal output
99 SW-F-CHG O Super woofer mode signal output
100 STK-MUTE O Power amp ON/OFF signal output

– 91 –
PANEL BOARD IC601 TMP87CM75 (DISPLAY CONTROL)

Pin No. Pin Name I/O Function

1 SEG-35 O FL segment signal output
2 V-LOAD – –25V driving power for FL
3-10 LED1-LED8 O LED driver signal output
11 Vss – Ground
12 X-OUT O X’tal (8MHz)
13 X-IN I X’tal (8MHz)
14 RESET I Reset signal input
15.16 LED9•10 O LED driver signal output
17 TEST I Conected ground
18-23 LED11-16 O LED driver signal output
24 VOL-A I Volume encoder signal input
25 LED17 O LED driver signal output
26 JOG-A I Jog dial encoder signal input
27 CLOCK I Serial clock input from main comtroller
28 DATA I Serial data input from main comtroller
29 LED SELECT O LED select signal output
30 VDD – +5V
31 VSS – Ground
32 MODEL I Version select signal input
33-37 KEY1-KEY5 I Key matrix input
38 DOOR SW I Door swith ON/OFF signal input
39 SIRCS I Remote commander signal input
40 VOL-B I Volume encoder signal input
41 JOG-B I Jog dial encoder signal input
42-45 SPEANA1-4 I Spectrum analyzer input
46 L+R I Spectrum analyzer (L,R) input
47 LED18 O LED driver signal output
48 VASS – Ground
49 VA REF – Analog reference volltage (+5v)
50 VDD – +5V
51-66 GR1-16 O FL grid signal output
67-100 SEG1-34 O FL segment signal output

– 92 –
 SECTION 7
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they • Abbreviation The components identified by mark
may have some difference from the original EA : Saudi Arabia model ! or dotted line with mark ! are
SP : Singapore model critical for safety.
one. Replace only with part number
• Items marked “*” are not stocked since they IA : Indonesian model specified.
are seldom required for routine service. Some MY : Malaysia model
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference num-
ber in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.

(1) CASE, REAR PANEL SECTION

#2

2
#2

1
#2 #3

1 #1

#1

5 4

#1

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 4-929-973-01 SCREW (CASE, 3 POINT) * 3 4-987-926-61 PANEL, BACK (SP)
* 2 4-987-052-31 CASE * 3 4-987-926-71 PANEL, BACK (MY)
* 3 4-987-926-41 PANEL, BACK (E,IA) * 4 A-4303-512-A TCB BOARD, COMPLETE
* 3 4-987-926-51 PANEL, BACK (EA) 5 1-769-974-11 WIRE (FLAT TYPE) (13 CORE)

– 93 –
(2) FRONT PANEL SECTION-1

58
59 73
TCM-220WR2 57
61
57 57
57
60 62 not
supplied
55 #1 57

56 62

57
65 not 63
supplied
66 57
54 64

67 57
57
75
53 70 74
supplied 68
with S711
57
71
52 69
51 72

57

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 4-987-995-01 SPRING (CD EJECT), COMPRESSION 64 4-987-038-31 LID DISK
52 4-987-001-01 BUTTON (EJECT CD) * 65 4-987-933-01 BRACKET (TA)
* 53 1-664-019-11 CD-A SW BOARD 66 4-987-000-02 BUTTON (EJECT B)
54 X-4948-348-1 PANEL (A) SUB ASSY * 67 1-664-013-11 TC-B SW BOARD
* 55 1-664-012-11 TC-A SW BOARD * 68 1-664-020-11 CD-B1 SW BOARD

56 4-986-999-02 BUTTON (EJECT A) 69 X-4947-969-1 BUTTON (CD STOP) ASSY

57 4-951-620-01 SCREW (2.6X8), +BVTP 70 4-987-037-01 KNOB (JOG)
58 1-773-161-11 WIRE (FLAT TYPE) (21 CORE) 71 X-4948-296-1 PANEL (B) SUB ASSY
59 1-769-949-11 WIRE (FLAT TYPE) (11 CORE) * 72 1-664-021-11 CD-B2 SW BOARD
60 3-354-963-01 DAMPER 73 A-4384-681-A LID ASSY, CD

* 61 1-664-017-11 LED BOARD 74 4-987-014-01 INDICATOR (CD)

62 4-957-577-01 SCREW PTP WH (2.6X8) (DIA. 10) 75 4-987-002-01 BUTTON (CD,PLAY)
* 63 1-664-016-11 DOOR SW BOARD

– 94 –
(3) FRONT PANEL SECTION-2

Supplied with 111 110

Supplied with 110
RV760
J761 not 120
supplied

112
109
supplied with
J760
115
114
108
106 118
113 119
117 110 121
107
116

105
123 122

124
104
125

126
127
supplied
with S701 not supplied 127
not
supplied 110
not supplied

102
103
128
101

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 A-4384-405-A PANEL ASSY, FRONT (E,EA,SP,IA) 115 X-4947-965-1 BUTTON (SOUND) ASSY
101 A-4384-729-A PANEL ASSY, FRONT (MY) 116 4-986-990-01 BUTTON (CURSOR)
102 4-987-036-01 KNOB (VOL) 117 4-978-683-01 SPRING, COMPRESSION
103 X-4947-961-1 LID ASSY, CASSETTE * 118 4-987-041-01 COVER, CURSOR
104 4-987-032-01 DISPLAY (TA) 119 X-4947-963-1 BUTTON (FUNCTION) ASSY

105 4-987-028-01 DISPLAY (ST) * 120 A-4392-472-A PANEL BOARD, COMPLETE

106 4-987-021-01 INDICATOR (TC A) 121 1-773-051-11 WIRE (FLAT TYPE) (17 CORE)
107 4-986-997-01 BUTTON (DECK.A) 122 X-4947-962-1 BUTTON (TUNER) ASSY
108 4-963-404-21 EMBLEM (5-A), SONY 123 4-987-013-01 INDICATOR (TUNER)
109 4-973-644-01 KNOB (MIC) 124 X-4947-968-1 BUTTON (WOOFER) ASSY

110 4-951-620-01 SCREW (2.6X8), +BVTP 125 X-4947-967-1 BUTTON (DECK B) ASSY
* 111 A-4398-651-A HEADPHONE-MIC BOARD, COMPLETE 126 4-987-022-01 INDICATOR (TC B)
112 4-986-986-01 BUTTON (POWER) 127 4-987-996-01 SPRING (TC LID), TENSION
113 4-987-017-01 INDICATOR (KEY CONTROL) 128 4-948-236-01 CUSHION (107)
114 4-987-012-01 INDICATOR (TA)

– 95 –
(4) CHASSIS SECTION

not supplied
151 #1
#2

#1
not supplied
#1
T901

161
#4 E, IA
153
154
#1
156 159
not
supplied CNP901
155 EA, MY, SP EA, SP
CDM37L-5BD29AL
#1

#1 160
#1
CNP901

#1

157

not supplied

158
The components identified by
mark ! or dotted line with
#1 mark ! are critical for safety.
not supplied Replace only with part number
specified.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 151 1-664-014-11 TRANS BOARD 159 1-569-007-11 ADAPTOR, CONVERSION 2P (E,IA)
153 3-703-244-00 BUSHING (FBS001), CORD (MY) 160 1-569-008-11 ADAPTOR, CONVERSION 2P (EA,SP)
153 4-966-266-01 BUSHING (S) (FBS002), CORD (EXCEPT MY) * 161 4-988-533-01 HOLDER, PCB (MALAYSIA PRODUCT)
* 154 A-4392-436-A POWERAMP BOARD, CONPLETE * 161 4-988-533-11 HOLDER, PCB (EXCEPT MALAYSIA PRODUCT)
* 155 A-4392-469-A MAIN BOARD, CONPLETE ! CNP901 1-558-943-41 CORD, POWER (E,IA)

* 156 A-4392-488-A KEY CON BOARD ! CNP901 1-575-651-21 CORD, POWER (EA,SP,MY)
157 1-777-868-11 WIRE (FLAT TYPE) (19 CORE) ! T901 1-431-052-11 TRANSFORMER, POWER
158 X-4941-228-1 FOOT (F22125H-M)

– 96 –
(5) TAPE MECHANISM DECK SECTION-1
(TCM-220WR2)

208

202

209

206

210
#5
#5

#5
207 206
208

204 203
not supplied

205

#2

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
202 X-4947-943-1 HOLDER (L) ASSY, CASSETTE * 207 4-980-439-01 FULCRUM, HOLDER
203 X-4947-944-1 HOLDER (R) ASSY, CASSETTE 208 3-354-957-01 JOINT (LOCK LEVER)
204 4-959-231-11 SPRING (L), TORSION 209 3-354-953-01 LEVER (LOCK LEVER L)
205 4-959-232-11 SPRING (R), TORSION 210 3-354-954-01 LEVER (LOCK LEVER R)
206 3-354-963-01 DAMPER

– 97 –
(6) TAPE MECHANISM DECK SECTION-2
(TCM-220WR2)

#6

270 269
(including r C)
273
rA
#6

265 271
264

not supplied 272

HP101 266
(including r A)
rA
257 263 269 rB
262
261 265
258 264
256
259 272
267
rB
260 not supplied 266 269
255 not supplied
HRPE101 268 262
254 (including r B) 257
not supplied 253 263
256 261
not supplied 259
255
252 258
#7 260
251
254
not supplied 253
not supplied
252 #7
251

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
251 3-908-560-01 SPRING, AZIMUTH ADJUSTMENT 263 X-3369-908-1 PINCH LEVER (FWD) ASSY
252 3-919-684-01 SCREW, AZIMUTH ADJUSTMENT 264 3-908-613-01 GEAR (S), REEL
253 X-3373-113-1 SLIDER (HEAD) ASSY 265 3-917-141-01 SPRING, COMPRESSION
254 3-908-556-01 SPRING, HEAD TOGGLE 266 X-3371-305-1 REEL (T) ASSY
255 3-908-558-02 FITTING BLOCK, HEAD 267 3-669-465-01 WASHER (1.5), STOPPER

256 3-908-557-02 ROTARY BLOCK, HEAD 268 X-3370-173-1 TU ASSY

* 257 3-908-559-01 STOPPER, AZIMUTH 269 3-939-862-01 CLIP
258 3-908-555-01 SLIDER (REV SLIDER) * 270 A-2007-131-A AUDIO BOARD, COMPLETE
259 3-917-143-11 SPRING, TENSION 271 3-930-972-01 DETENT, HALF
260 3-388-848-01 SCREW (P2X6) (B TIGHT) 272 3-917-142-01 SPRING, COMPRESSION

261 3-939-371-01 SPRING (1), TENSION 273 3-938-863-01 STOPPER

262 X-3369-909-1 PINCH LEVER (REV) ASSY HP101 1-500-093-11 HEAD, MAGNETIC (PLAYBACK)
HRPE1011-500-094-11 HEAD, MAGNETIC (REC/PB/ERASE)

– 98 –
(7) TAPE MECHANISM DECK SECTION-3
(TCM-220WR2)
r C : MOTOR board (supplied with AUDIO board) M2

rC

318
319

#10
#11

310 321
317 320
#10

302 311

321
309 316 310
#7 325
313
315
308
306
307 319
323
305

312
322 307
304
314
313 #8

303
#9 301
#9
302

M1 not supplied

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
301 3-908-597-01 CAM (A) 315 3-908-600-01 LEVER (REV-B)
302 3-908-608-11 SCREW, STEP * 316 1-650-669-11 LEAF SWITCH BOARD
303 X-3372-930-1 ARM (A) ASSY, FR 317 3-908-598-01 CAM (B)
304 X-3370-882-1 FLYWHEEL (AR) ASSY 318 X-3372-931-1 ARM (B) ASSY, FR
305 3-928-047-01 PULLEY, TENSION 319 3-914-111-01 SPRING (FR), TORSION

306 3-908-599-01 LEVER (REV-A) 320 3-908-604-01 LEVER (TRIGGER B)

307 3-908-601-01 SPRING (REV LEVER), TORSION 321 3-911-115-01 WASHER, STOPPER
308 3-908-603-01 LEVER (TRIGGER A) 322 3-917-176-11 BELT (B)
309 X-3367-108-1 FLYWHEEL (BF) ASSY 323 X-3370-172-1 FLYWHEEL (AF) ASSY
310 3-908-605-01 SPRING (TRIGGER), TORSION
325 X-3371-441-1 CHASSIS ASSY, MECHANICAL
311 3-908-609-01 GEAR, TRIGGER M1 X-3371-223-1 MOTOR ASSY, CAPSTAN
312 3-913-845-11 BELT (A) M2 A-2004-410-A MOTOR ASSY, DC (TRIGGER)
313 3-913-846-11 BELT (FR)
314 X-3370-171-1 FLYWHEEL (BR) ASSY

– 99 –
(8) CD MECHANISM DECK SECTION
(CDM37L-5BD29AL)

352 358 351

351
351

355
353

354 356
359
357 #1
360
361
360
359 359

360
375
373
362 372 374

352
368
M201 368
367 368 BU-5BD29AL
369
not 369
supplied

363 365 #1

361
370
#1 366
#1 #1
364 371

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
351 4-987-976-01 SCREW, STEP * 364 A-4673-765-A CD MOTOR BOARD, COMPLETE
352 4-944-490-01 BELT (TIMING) 365 4-978-426-01 INDICATOR (NO.)
353 A-4660-978-A GEAR (PULLEY) ASSY * 366 1-659-059-13 BD LED BOARD
354 4-978-421-01 GEAR (MID) * 367 1-659-058-13 TABLE SENSOR BOARD
355 4-978-425-01 ROLLER (CAM) 368 4-933-134-01 SCREW (+PTPWH M2.6X6)

356 4-978-420-01 CAM (HOLDER) 369 4-958-593-01 SPRING (BU), COMPRESSION

357 1-452-538-11 MAGNET * 370 4-978-419-01 HOLDER (BU-5)
358 4-978-417-01 TABLE, DISC 371 4-917-583-71 BRACKET, YOKE
359 4-934-376-01 SHAFT (ROLLER) * 372 4-989-493-01 SLIDER (37)
360 X-4924-457-1 ROLLER ASSY 373 4-989-494-01 SCREW (SLIDER), STEP

* 361 4-978-583-01 BRACKET (BU) 374 4-989-819-01 SPRING, TENSION

* 362 4-978-418-01 CHASSIS * 375 4-989-491-21 COVER, LENS
* 363 4-980-385-01 HOLDER(SW) M201 A-4660-977-A MOTOR ASSY (TABLE)

– 100 –
(9) BASE UNIT SECTION
(BU-5BD29AL)

401

402

#12

403

M101 404
405
M102

404

406

407

408

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
! 401 8-820-020-01 OPTICAL PICK-UP KSS-213D/Q-NP 406 4-917-564-01 GEAR (P), FLATNESS
402 1-769-069-11 WIRE (FLAT TYPE) (16 CORE) * 407 A-4699-522-A BD BOARD, COMPLETE
403 4-917-567-21 GEAR (M) 408 4-951-620-01 SCREW (2.6X8), +BVTP
404 4-951-940-01 INSULATOR (BU) M101 X-4917-504-1 MOTOR ASSY (SPINDLE)
405 4-917-565-01 SHAFT, SLED M102 X-4917-523-4 MOTOR ASSY (SLED)

The components identified by

mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number
specified.

– 101 –
 SECTION 8
AUDIO ELECTRICAL PARTS LIST

NOTE:
• Due to standardization, replacements in the • SEMICONDUCTORS The components identified by mark
parts list may be different from the parts speci- In each case, u: µ, for example: ! or dotted line with mark ! are
fied in the diagrams or the components used on uA. . : µA. . uPA. . : µPA. . critical for safety.
the set. uPB. . : µPB. . uPC. . : µPC. . Replace only with part number
specified.
uPD. . : µPD. .
• -XX and -X mean standardized parts, so they
may have some difference from the original one. • CAPACITORS
uF: µF When indicating parts by reference
• RESISTORS number, please include the board.
All resistors are in ohms. • COILS
METAL: Metal-film resistor. uH: µH
METAL OXIDE: Metal oxide-film resistor.
• Abbreviation
F: nonflammable
EA : Saudi arabia
• Items marked “*” are not stocked since they
SP : Singapore
are seldom required for routine service.
IA : Indonesia
Some delay should be anticipated when order-
MY : Malaysia
ing these items.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* A-2007-131-A AUDIO BOARD, COMPLETE < CONNECTOR >
*********************
(including MOTOR BOARD) CN601 1-695-382-31 PIN, CONNECTOR (PC BOARD) 21P
CN602 1-564-718-11 PIN, CONNECTOR (SMALL TYPE) 2P
< CAPACITOR > * CN651 1-564-521-11 PLUG, CONNECTOR 6P

C301 1-162-289-31 CERAMIC 390PF 10% 50V < IC >

C302 1-126-968-11 ELECT 100uF 20% 6.3V
C303 1-162-282-31 CERAMIC 100PF 10% 50V IC601 8-759-111-44 IC uPC4570C-1
C304 1-130-483-00 MYLAR 0.01uF 5% 50V IC602 8-759-143-54 IC uPC1330HA
C305 1-107-715-11 ELECT 22uF 20% 16V IC611 8-759-111-44 IC uPC4570C-1

C311 1-162-289-31 CERAMIC 390PF 10% 50V < COIL >

C313 1-162-282-31 CERAMIC 100PF 10% 50V
C314 1-130-487-00 MYLAR 0.022uF 5% 50V L331 1-410-780-11 INDUCTOR 27mH
C315 1-126-233-11 ELECT 22uF 20% 50V L431 1-410-780-11 INDUCTOR 27mH
C331 1-137-427-11 FILM 120PF 5% 50V
< TRANSISTOR >
C332 1-162-288-31 CERAMIC 330PF 10% 50V
C333 1-162-209-31 CERAMIC 27PF 5% 50V Q621 8-729-142-46 TRANSISTOR 2SC2001-LK
C401 1-162-289-31 CERAMIC 390PF 10% 50V Q622 8-729-142-46 TRANSISTOR 2SC2001-LK
C402 1-126-968-11 ELECT 100uF 20% 6.3V Q623 8-729-801-93 TRANSISTOR 2SD1387
C403 1-162-282-31 CERAMIC 00PF 10% 50V Q651 8-729-900-65 TRANSISTOR DTA144ES

C404 1-130-483-00 MYLAR 0.01uF 5% 50V < RESISTOR >

C405 1-107-715-11 ELECT 22uF 20% 16V
C411 1-162-289-31 CERAMIC 390PF 10% 50V R301 1-247-881-00 CARBON 120K 5% 1/4W
C413 1-162-282-31 CERAMIC 100PF 10% 50V R302 1-249-409-11 CARBON 220 5% 1/4W
C414 1-130-487-00 MYLAR 0.022uF 5% 50V R303 1-249-433-11 CARBON 22K 5% 1/4W
R304 1-247-889-00 CARBON 270K 5% 1/4W
C415 1-126-233-11 ELECT 22uF 20% 50V R305 1-247-858-11 CARBON 13K 5% 1/4W
C431 1-137-427-11 FILM 120PF 5% 50V
C432 1-162-288-31 CERAMIC 330PF 10% 50V R311 1-247-881-00 CARBON 120K 5% 1/4W
C433 1-162-209-31 CERAMIC 27PF 5% 50V R312 1-247-807-31 CARBON 100 5% 1/4W
C601 1-104-396-11 ELECT 10uF 20% 16V R314 1-247-882-11 CARBON 130K 5% 1/4W
R315 1-247-850-11 CARBON 6.2K 5% 1/4W
C602 1-104-396-11 ELECT 10uF 20% 16V R331 1-249-430-11 CARBON 12K 5% 1/4W
C611 1-124-907-11 ELECT 10uF 20% 50V
C612 1-124-907-11 ELECT 10uF 20% 50V R401 1-247-881-00 CARBON 120K 5% 1/4W
C621 1-137-150-11 FILM 0.01uF 5% 100V R402 1-249-409-11 CARBON 220 5% 1/4W
C622 1-126-961-11 ELECT 2.2uF 20% 50V R403 1-249-433-11 CARBON 22K 5% 1/4W
R404 1-247-889-00 CARBON 270K 5% 1/4W
C623 1-136-155-00 FILM 0.015uF 5% 50V R405 1-247-858-11 CARBON 13K 5% 1/4W
C624 1-130-481-00 MYLAR 0.0068uF 5% 50V
C625 1-130-481-00 MYLAR 0.0068uF 5% 50V R411 1-247-881-00 CARBON 120K 5% 1/4W
C627 1-124-903-11 ELECT 1uF 20% 50V R412 1-247-807-31 CARBON 100 5% 1/4W
C628 1-136-153-00 FILM 0.01uF 5% 50V R414 1-247-882-11 CARBON 130K 5% 1/4W
R415 1-247-850-11 CARBON 6.2K 5% 1/4W
C642 1-104-664-11 ELECT 47uF 20% 16V R431 1-249-430-11 CARBON 12K 5% 1/4W
C651 1-161-494-00 CERAMIC 0.022uF 25V
R601 1-249-409-11 CARBON 220 5% 1/4W
R602 1-249-409-11 CARBON 220 5% 1/4W

– 102 –
 AUDIO BD
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R608 1-249-409-11 CARBON 220 5% 1/4W C127 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
R609 1-249-433-11 CARBON 22K 5% 1/4W C128 1-163-135-00 CERAMIC CHIP 560PF 5% 50V
R611 1-249-409-11 CARBON 220 5% 1/4W C129 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C130 1-164-336-11 CERAMIC CHIP 0.33uF 25V
R612 1-249-409-11 CARBON 220 5% 1/4W C131 1-164-346-11 CERAMIC CHIP 1uF 16V
! R621 1-212-851-00 FUSIBLE 5.6 5% 1/4W F
! R622 1-212-851-00 FUSIBLE 5.6 5% 1/4W F C140 1-110-501-11 CERAMIC CHIP 0.33uF 10% 16V
R623 1-249-432-11 CARBON 18K 5% 1/4W C154 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
R624 1-249-432-11 CARBON 18K 5% 1/4W C161 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C162 1-164-232-11 CERAMIC CHIP 0.01uF 50V
R625 1-249-429-11 CARBON 10K 5% 1/4W C163 1-163-117-00 CERAMIC CHIP 100PF 5% 50V
R651 1-247-856-00 CARBON 11K 5% 1/4W
R652 1-247-856-00 CARBON 11K 5% 1/4W C164 1-163-145-00 CERAMIC CHIP 0.0015uF 5% 50V
R653 1-249-441-11 CARBON 100K 5% 1/4W C165 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C166 1-163-137-00 CERAMIC CHIP 680PF 5% 50V
C167 1-163-121-00 CERAMIC CHIP 150PF 5% 50V
< VARIABLE RESISTOR > C168 1-163-137-00 CERAMIC CHIP 680PF 5% 50V

RV301 1-238-598-11 RES, ADJ, CARBON 2.2K C169 1-163-121-00 CERAMIC CHIP 150PF 5% 50V
RV311 1-238-598-11 RES, ADJ, CARBON 2.2K C170 1-163-099-00 CERAMIC CHIP 18PF 5% 50V
RV341 1-238-551-11 RES, ADJ, CARBON 220K C171 1-163-237-11 CERAMIC CHIP 27PF 5% 50V
RV401 1-238-598-11 RES, ADJ, CARBON 2.2K C173 1-163-038-91 CERAMIC CHIP 0.1uF 25V
RV411 1-238-598-11 RES, ADJ, CARBON 2.2K C174 1-163-038-91 CERAMIC CHIP 0.1uF 25V

RV441 1-238-551-11 RES, ADJ, CARBON 220K C175 1-163-038-91 CERAMIC CHIP 0.1uF 25V
RV651 1-238-599-11 RES, ADJ, CARBON 4.7K C176 1-163-038-91 CERAMIC CHIP 0.1uF 25V
RV652 1-238-599-11 RES, ADJ, CARBON 4.7K C177 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C178 1-163-038-91 CERAMIC CHIP 0.1uF 25V
< TRANSFORMER > C179 1-163-038-91 CERAMIC CHIP 0.1uF 25V

T621 1-423-980-11 TRANSFORMER, BIAS OSCILLATION C181 1-126-205-11 ELECT CHIP 47uF 20% 6.3V
************************************************************ C182 1-126-393-11 ELECT 33uF 20% 10V
C183 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
* A-4699-522-A BD BOARD, COMPLETE C185 1-164-232-11 CERAMIC CHIP 0.01uF 50V
******************* C188 1-163-235-11 CERAMIC CHIP 22PF 5% 50V

< CAPACITOR > C189 1-163-235-11 CERAMIC CHIP 22PF 5% 50V

C101 1-126-607-11 ELECT CHIP 47uF 20% 4V < CONNECTOR >

C102 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
C103 1-164-346-11 CERAMIC CHIP 1uF 16V CNU101 1-777-937-11 CONNECTOR, FFC/FPC 16P
C105 1-163-038-91 CERAMIC CHIP 0.1uF 25V CNU102 1-778-874-11 CONNECTOR, FFC(LIF(NON-ZIF))19P
C106 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
< FERRITE BEAD >
C107 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
C108 1-164-232-11 CERAMIC CHIP 0.01uF 50V FB101 1-414-234-11 INDUCTOR, FERRITE BEAD
C109 1-164-232-11 CERAMIC CHIP 0.01uF 50V FB103 1-414-234-11 INDUCTOR, FERRITE BEAD
C110 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V
C111 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V < IC >

C112 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V IC101 8-752-080-62 IC CXA1992AR

C113 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V IC102 8-759-429-32 IC BA5941FP-E2
C114 1-164-005-11 CERAMIC CHIP 0.47uF 25V IC103 8-752-378-66 IC CXD2519Q
C115 1-126-607-11 ELECT CHIP 47uF 20% 4V
C116 1-163-016-00 CERAMIC CHIP 0.0039uF 10% 50V < JUMPER RESISTOR >

C117 1-164-005-11 CERAMIC CHIP 0.47uF 25V JW101 1-216-295-91 CONDUCTOR, CHIP (2012)
C118 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V JW104 1-216-295-91 CONDUCTOR, CHIP (2012)
C119 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C120 1-124-779-00 ELECT CHIP 10uF 20% 16V < TRANSISTOR >
C121 1-163-038-91 CERAMIC CHIP 0.1uF 25V
Q101 8-729-010-08 TRANSISTOR MSB710-R
C122 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C123 1-163-038-91 CERAMIC CHIP 0.1uF 25V < RESISTOR >
C124 1-126-607-11 ELECT CHIP 47uF 20% 4V
C125 1-164-232-11 CERAMIC CHIP 0.01uF 50V R102 1-216-001-00 METAL CHIP 10 5% 1/10W
C126 1-163-038-91 CERAMIC CHIP 0.1uF 25V R104 1-216-093-00 METAL CHIP 68K 5% 1/10W
R105 1-216-088-00 METAL CHIP 43K 5% 1/10W

The components identified by

mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number
specified.
– 103 –
 BD BD LED CD MOTOR CD-A SW
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R106 1-216-088-00 METAL CHIP 43K 5% 1/10W < SWITCH >
R107 1-216-088-00 METAL CHIP 43K 5% 1/10W
S101 1-572-085-11 SWITCH, LEAF
R108 1-216-088-00 METAL CHIP 43K 5% 1/10W
R109 1-216-093-00 METAL CHIP 68K 5% 1/10W < VIBRATOR >
R114 1-216-101-00 METAL CHIP 150K 5% 1/10W
R115 1-216-101-00 METAL CHIP 150K 5% 1/10W X101 1-767-408-21 VIBRATOR, CRYSTAL (16.9344MHz)
R116 1-216-061-00 METAL CHIP 3.3K 5% 1/10W ************************************************************

R117 1-216-069-00 METAL CHIP 6.8K 5% 1/10W * 1-659-059-13 BD LED BOARD

R118 1-216-063-91 METAL GLAZE 3.9K 5% 1/10W ************
R119 1-216-085-00 METAL CHIP 33K 5% 1/10W
R120 1-216-089-91 METAL GLAZE 47K 5% 1/10W * 4-980-385-01 HOLDER (SW)
R121 1-216-114-00 METAL GLAZE 510K 5% 1/10W
< DIODE >
R122 1-216-097-91 METAL GLAZE 100K 5% 1/10W
R123 1-216-099-00 METAL CHIP 120K 5% 1/10W D201 8-719-032-98 DIODE SEL5820A
R124 1-216-091-00 METAL CHIP 56K 5% 1/10W
R125 1-216-069-00 METAL CHIP 6.8K 5% 1/10W < TRANSISTOR >
R126 1-216-063-91 METAL GLAZE 3.9K 5% 1/10W
Q201 8-729-119-78 TRANSISTOR 2SC403SP-51
R127 1-216-089-91 METAL GLAZE 47K 5% 1/10W
R128 1-216-098-00 METAL CHIP 110K 5% 1/10W < RESISTOR >
R129 1-216-025-91 METAL GLAZE 100 5% 1/10W
R130 1-216-079-00 METAL CHIP 18K 5% 1/10W R201 1-247-863-91 CARBON 22K 5% 1/4W
R131 1-216-079-00 METAL CHIP 18K 5% 1/10W R202 1-249-411-11 CARBON 330 5% 1/4W
R203 1-249-437-11 CARBON 47K 5% 1/4W
R132 1-216-061-00 METAL CHIP 3.3K 5% 1/10W ************************************************************
R133 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R134 1-216-065-00 METAL CHIP 4.7K 5% 1/10W * A-4673-765-A CD MOTOR BOARD, COMPLETE
R135 1-216-065-00 METAL CHIP 4.7K 5% 1/10W *************************
R136 1-216-073-00 METAL CHIP 10K 5% 1/10W
< CAPACITOR >
R137 1-216-065-00 METAL CHIP 4.7K 5% 1/10W
R138 1-216-025-91 METAL GLAZE 100 5% 1/10W C201 1-124-907-11 ELECT 10uF 20% 50V
R156 1-216-081-00 METAL CHIP 22K 5% 1/10W C202 1-164-159-21 CERAMIC 0.1uF 50V
R157 1-216-069-00 METAL CHIP 6.8K 5% 1/10W C203 1-124-907-11 ELECT 10uF 20% 50V
R158 1-216-001-00 METAL CHIP 10 5% 1/10W
< CONNECTOR >
R159 1-216-121-91 METAL GLAZE 1M 5% 1/10W
R161 1-216-097-91 METAL GLAZE 100K 5% 1/10W * CN201 1-568-947-11 PIN, CONNECTOR 9P
R162 1-216-073-00 METAL CHIP 10K 5% 1/10W
R163 1-216-121-91 METAL GLAZE 1M 5% 1/10W < IC >
R164 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
IC201 8-759-365-94 IC TA8409S
R165 1-216-049-91 METAL GLAZE 1K 5% 1/10W
R166 1-216-073-00 METAL CHIP 10K 5% 1/10W < COIL >
R167 1-216-081-00 METAL CHIP 22K 5% 1/10W
R168 1-216-073-00 METAL CHIP 10K 5% 1/10W L201 1-408-117-00 INDUCTOR 10uH
R169 1-216-079-00 METAL CHIP 18K 5% 1/10W
< RESISTOR >
R170 1-216-081-00 METAL CHIP 22K 5% 1/10W
R171 1-216-073-00 METAL CHIP 10K 5% 1/10W R205 1-249-427-11 CARBON 6.8K 5% 1/4W
R172 1-216-079-00 METAL CHIP 18K 5% 1/10W R206 1-249-425-11 CARBON 4.7K 5% 1/4W
R173 1-216-025-91 METAL GLAZE 100 5% 1/10W
R174 1-216-033-00 METAL CHIP 220 5% 1/10W < SWITCH >

R175 1-216-025-91 METAL GLAZE 100 5% 1/10W S201 1-762-587-11 SWITCH, PUSH (1 KEY)
R176 1-216-025-91 METAL GLAZE 100 5% 1/10W ************************************************************
R177 1-216-025-91 METAL GLAZE 100 5% 1/10W
R178 1-216-025-91 METAL GLAZE 100 5% 1/10W * 1-664-019-11 CD-A SW BOARD
R179 1-216-025-91 METAL GLAZE 100 5% 1/10W *************

R180 1-216-025-91 METAL GLAZE 100 5% 1/10W < DIODE >

R181 1-216-025-91 METAL GLAZE 100 5% 1/10W
R188 1-216-037-00 METAL CHIP 330 5% 1/10W D641 8-719-058-04 DIODE SEL5223S-TP15 (NON-STOP)
R190 1-216-097-91 METAL GLAZE 100K 5% 1/10W
R191 1-216-105-91 METAL GLAZE 220K 5% 1/10W < RESISTOR >

R731 1-249-411-11 CARBON 330 5% 1/4W

R732 1-249-413-11 CARBON 470 5% 1/4W

– 104 –
 CD-A SW CD-B1 SW CD-B2 SW DOOR SW HEADPHONE-MIC

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R733 1-249-415-11 CARBON 680 5% 1/4W S686 1-554-303-21 SWITCH, TACTILE (0)
R734 1-249-417-11 CARBON 1K 5% 1/4W S711 1-467-968-11 ENCODER, ROTARY (≠ AMS ±)
R735 1-249-419-11 CARBON 1.5K 5% 1/4W ************************************************************

R736 1-249-421-11 CARBON 2.2K 5% 1/4W * 1-664-016-11 DOOR SW BOARD

R737 1-249-417-11 CARBON 1K 5% 1/4W ***************
R741 1-247-807-31 CARBON 100 5% 1/4W
< CAPACITOR >
< SWITCH >
C691 1-164-159-21 CERAMIC 0.1uF 50V
S661 1-554-303-21 SWITCH, TACTILE (DISC 1)
S662 1-554-303-21 SWITCH, TACTILE (DISC 2) < CONNECTOR >
S663 1-554-303-21 SWITCH, TACTILE (DISC 3)
S664 1-554-303-21 SWITCH, TACTILE (DISC 4) CN661 1-506-481-11 PIN, CONNECTOR 2P
S665 1-554-303-21 SWITCH, TACTILE (DISC 5)
< SWITCH >
S666 1-554-303-21 SWITCH, TACTILE (FLASH)
S667 1-554-303-21 SWITCH, TACTILE (NON-STOP) S691 1-771-057-11 SWITCH, PUSH (1 KEY) (6 OPEN)
S668 1-554-303-21 SWITCH, TACTILE (LOOP) ************************************************************
************************************************************
* A-4392-486-A HEADPHONE-MIC BOARD, COMPLETE
* 1-664-020-11 CD-B1 SW BOARD *******************************
**************
* 1-690-880-21 LEAD (WITH CONNECTOR)
< CONNECTOR >
< CAPACITOR >
* CN642 1-568-943-11 PIN, CONNECTOR 5P
C760 1-162-306-11 CERAMIC 0.01uF 20% 16V
< DIODE > C761 1-126-961-11 ELECT 2.2uF 20% 50V
C762 1-162-306-11 CERAMIC 0.01uF 30% 16V
D645 8-719-057-29 DIODE SML78423C-TP15 (·) C763 1-126-961-11 ELECT 2.2uF 20% 50V
D646 8-719-057-97 DIODE SEL5923A-TP15 (P) C764 1-162-294-31 CERAMIC 0.001uF 10% 50V
D647 8-719-057-29 DIODE SML78423C-TP15 (·)
C765 1-162-215-31 CERAMIC 47PF 5% 50V
< RESISTOR > C766 1-162-290-31 CERAMIC 470PF 10% 50V
C767 1-162-215-31 CERAMIC 47PF 5% 50V
R745 1-247-815-91 CARBON 220 5% 1/4W C768 1-126-961-11 ELECT 2.2uF 20% 50V
R746 1-249-411-11 CARBON 330 5% 1/4W C769 1-162-282-31 CERAMIC 100PF 10% 50V
R747 1-249-413-11 CARBON 470 5% 1/4W
R748 1-249-415-11 CARBON 680 5% 1/4W C770 1-126-961-11 ELECT 2.2uF 20% 50V
R749 1-247-807-31 CARBON 100 5% 1/4W C771 1-126-959-11 ELECT 0.47uF 20% 50V
C773 1-126-964-11 ELECT 10uF 20% 50V
R750 1-247-807-31 CARBON 100 5% 1/4W C774 1-126-964-11 ELECT 10uF 20% 50V
R751 1-247-807-31 CARBON 100 5% 1/4W C775 1-162-294-31 CERAMIC 0.001uF 10% 50V

< SWITCH > C776 1-162-294-31 CERAMIC 0.001uF 10% 50V

C777 1-126-960-11 ELECT 1uF 20% 50V
S676 1-554-303-21 SWITCH, TACTILE (·) C778 1-162-305-11 CERAMIC 6800pF 30% 16V
S677 1-554-303-21 SWITCH, TACTILE (p) C779 1-162-294-31 CERAMIC 0.001uF 10% 50V
S678 1-554-303-21 SWITCH, TACTILE (P) C780 1-136-495-11 FILM 0.068uF 5% 50V
S679 1-554-303-21 SWITCH, TACTILE (DISC SKIP)
************************************************************ C781 1-126-957-11 ELECT 0.22uF 20% 50V
C782 1-126-957-11 ELECT 0.22uF 20% 50V
* 1-664-021-11 CD-B2 SW BOARD C783 1-126-967-11 ELECT 47uF 20% 10V
************** C784 1-136-495-11 FILM 0.068uF 5% 50V
C785 1-162-305-11 CERAMIC 6800pF 30% 16V
< RESISTOR >
C786 1-162-294-31 CERAMIC 0.001uF 10% 50V
R752 1-249-417-11 CARBON 1K 5% 1/4W C787 1-124-250-11 ELECT 0.15uF 20% 50V
R753 1-249-419-11 CARBON 1.5K 5% 1/4W C788 1-126-960-11 ELECT 1uF 20% 50V
R754 1-249-421-11 CARBON 2.2K 5% 1/4W C789 1-161-494-00 CERAMIC 0.022uF 25V
R755 1-247-843-11 CARBON 3.3K 5% 1/4W C790 1-126-967-11 ELECT 47uF 20% 10V
R756 1-249-427-11 CARBON 6.8K 5% 1/4W
C791 1-164-159-21 CERAMIC 0.1uF 50V
< SWITCH > C794 1-164-159-21 CERAMIC 0.1uF 50V
C795 1-164-159-21 CERAMIC 0.1uF 50V
S681 1-554-303-21 SWITCH, TACTILE ())
S682 1-554-303-21 SWITCH, TACTILE (REPEAT) < CONNECTOR >
S683 1-554-303-21 SWITCH, TACTILE (PLAY MODE)
S684 1-554-303-21 SWITCH, TACTILE (1/ALL DISCS) * CN701 1-568-935-11 PIN, CONNECTOR 8P
S685 1-554-303-21 SWITCH, TACTILE (EDIT)

– 105 –
 HEADPHONE-MIC KEY CON

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< DIODE > C512 1-162-284-31 CERAMIC 150pF 10% 50V
C513 1-136-165-00 FILM 0.1uF 5% 50V
D761 8-719-200-82 DI0DE 11ES2-NTA1B C514 1-136-165-00 FILM 0.1uF 5% 50V
D762 8-719-200-82 DI0DE 11ES2-NTA1B C515 1-162-294-31 CERAMIC 0.001uF 10% 50V
D763 8-719-200-82 DI0DE 11ES2-NTA1B
C516 1-162-294-31 CERAMIC 0.001uF 10% 50V
< IC > C517 1-162-294-31 CERAMIC 0.001uF 10% 50V
C518 1-162-306-11 CERAMIC 0.01uF 30% 16V
IC760 8-759-634-51 IC M5218AP C519 1-162-294-31 CERAMIC 0.001uF 10% 50V
IC761 8-759-450-96 IC M65850P C520 1-126-964-11 ELECT 10uF 20% 50V

< JACK > C521 1-162-291-31 CERAMIC 560pF 10% 50V

C522 1-162-600-11 CERAMIC 0.0047uF 30% 16V
J760 1-770-226-11 JACK (LARGE TYPE) (PHONES) C523 1-162-290-31 CERAMIC 470pF 10% 50V
J761 1-770-226-11 JACK (LARGE TYPE) (MIC1) C524 1-126-964-11 ELECT 10uF 20% 50V
J762 1-770-226-11 JACK (LARGE TYPE) (MIC2) C525 1-126-964-11 ELECT 10uF 20% 50V

< COIL > C526 1-126-964-11 ELECT 10uF 20% 50V

C527 1-126-964-11 ELECT 10uF 20% 50V
L761 1-410-521-11 INDUCTOR 100uH C1439 1-126-964-11 ELECT 10uF 20% 50V

< RESISTOR > < CONNECTOR >

R760 1-249-429-11 CARBON 10K 5% 1/4W CN501 1-566-999-11 PIN,CONNECTOR 13P

R761 1-249-417-11 CARBON 1K 5% 1/4W
R762 1-249-429-11 CARBON 10K 5% 1/4W < IC >
R763 1-249-417-11 CARBON 1K 5% 1/4W
R764 1-249-441-11 CARBON 100K 5% 1/4W IC501 8-759-370-84 IC M65847FP-TP
IC502 8-759-140-53 IC uPD4053BC
R765 1-249-417-11 CARBON 1K 5% 1/4W
R766 1-249-437-11 CARBON 47K 5% 1/4W < COIL >
R767 1-249-429-11 CARBON 10K 5% 1/4W
R768 1-249-431-11 CARBON 15K 5% 1/4W L501 1-410-521-11 INDUCTOR 100uH
R769 1-247-885-00 CARBON 180K 5% 1/4W
< TRANSISTOR >
R770 1-247-807-31 CARBON 100 5% 1/4W
R771 1-247-863-91 CARBON 22K 5% 1/4W Q501 8-729-119-78 TRANSISTOR 2SC403SP-51
R772 1-247-863-91 CARBON 22K 5% 1/4W Q502 8-729-900-80 TRANSISTOR DTC114ES
R773 1-247-863-91 CARBON 22K 5% 1/4W
R774 1-247-881-00 CARBON 120K 5% 1/4W < RESISTOR >

R775 1-247-863-91 CARBON 22K 5% 1/4W R501 1-247-807-31 CARBON 100 5% 1/4W
R776 1-247-863-91 CARBON 22K 5% 1/4W R502 1-249-429-11 CARBON 10K 5% 1/4W
R777 1-247-863-91 CARBON 22K 5% 1/4W R503 1-247-807-31 CARBON 100 5% 1/4W
R778 1-249-437-11 CAABON 47K 5% 1/4W R504 1-249-425-11 CARBON 4.7K 5% 1/4W
R779 1-249-431-11 CARBON 15K 5% 1/4W R505 1-247-903-00 CARBON 1M 5% 1/4W

< VARIABLE RESISTOR > R506 1-249-429-11 CARBON 10K 5% 1/4W

R507 1-249-425-11 CARBON 4.7K 5% 1/4W
RV760 1-225-366-11 RES, VAR, CARBON 50K (MIC LEVEL) R508 1-249-429-11 CARBON 10K 5% 1/4W
RV761 1-225-366-11 RES, VAR, CARBON 50K (ECHO LEVEL) R509 1-249-434-11 CARBON 27K 5% 1/4W
************************************************************ R510 1-249-426-11 CARBON 5.6K 5% 1/4W

* A-4392-488-A KEY CON BOARD R511 1-249-424-11 CARBON 3.9K 5% 1/4W

************** R512 1-249-431-11 CARBON 15K 5% 1/4W
R513 1-249-429-11 CARBON 10K 5% 1/4W
< CAPACITOR > R514 1-247-863-91 CARBON 22K 5% 1/4W
R515 1-249-429-11 CARBON 10K 5% 1/4W
C501 1-124-584-00 ELECT 100uF 20% 6.3V
C502 1-164-159-21 CERAMIC 0.1uF 50V R516 1-249-441-11 CARBON 100K 5% 1/4W
C503 1-126-967-11 ELECT 47uF 20% 10V R517 1-247-863-91 CARBON 22K 5% 1/4W
C504 1-164-159-21 CERAMIC 0.1uF 50V R518 1-247-863-91 CARBON 22K 5% 1/4W
C505 1-162-600-11 CERAMIC 0.0047uF 30% 16V R519 1-249-441-11 CARBON 100K 5% 1/4W
R520 1-249-441-11 CARBON 100K 5% 1/4W
C506 1-162-286-21 CERAMIC 220pF 10% 50V
C507 1-162-286-21 CERAMIC 220pF 10% 50V R521 1-249-429-11 CARBON 10K 5% 1/4W
C508 1-136-495-11 FILM 0.068uF 5% 50V R522 1-249-425-11 CARBON 4.7K 5% 1/4W
C509 1-136-495-11 FILM 0.068uF 5% 50V R523 1-249-425-11 CARBON 4.7K 5% 1/4W
C510 1-136-495-11 FILM 0.068uF 5% 50V R524 1-249-429-11 CARBON 10K 5% 1/4W
R525 1-249-417-11 CARBON 1K 5% 1/4W
C511 1-164-159-21 CERAMIC 0.1uF 50V ***************************************************************

– 106 –
 LEAF SWITCH LED MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 1-650-669-11 LEAF SWITCH BOARD C152 1-162-282-31 CERAMIC 100PF 10% 50V
*****************
C153 1-162-282-31 CERAMIC 100PF 10% 50V
< CONNECTOR > C154 1-126-962-11 ELECT 3.3uF 20% 50V
C155 1-162-600-11 CERAMIC 0.0047uF 30% 16V
* CN1001 1-568-854-11 SOCKET, CONNECTOR 11P C156 1-162-301-11 CERAMIC 0.0015uF 30% 16V
C157 1-126-956-91 ELECT 0.1uF 20% 50V
< TRANSISTOR >
C171 1-162-286-21 CERAMIC 220PF 10% 50V
Q1001 8-749-010-90 TRANSISTOR PHOTO REFLECTOR C173 1-162-306-11 CERAMIC 0.01uF 20% 16V
NJL5165KA-H C201 1-136-167-00 FILM 0.15uF 5% 50V
Q1002 8-749-010-90 TRANSISTOR PHOTO REFLECTOR C202 1-136-167-00 FILM 0.15uF 5% 50V
NJL5165KA-H C203 1-130-493-00 MYLAR 0.068uF 5% 50V

< RESISTOR > C204 1-130-493-00 MYLAR 0.068uF 5% 50V

C205 1-130-486-00 MYLAR 0.018uF 10% 50V
R1001 1-247-818-11 CARBON 300 5% 1/4W C206 1-130-486-00 MYLAR 0.018uF 10% 50V
R1002 1-247-820-11 CARBON 360 5% 1/4W C207 1-130-480-00 MYLAR 0.0056uF 5% 50V
R1003 1-249-414-11 CARBON 560 5% 1/4W C208 1-130-479-00 MYLAR 0.0047uF 5% 50V
R1004 1-247-834-11 CARBON 1.3K 5% 1/4W
R1005 1-247-818-11 CARBON 300 5% 1/4W C209 1-130-474-00 MYLAR 0.0018uF 5% 50V
C210 1-126-964-11 ELECT 10uF 20% 50V
< SWITCH > C211 1-126-964-11 ELECT 10uF 20% 50V
C212 1-130-483-00 MYLAR 0.01uF 5% 50V
S1001 1-692-832-11 SWITCH, PUSH (1 KEY) (A PLAY) C213 1-136-171-00 FILM 0.33uF 5% 50V
S1002 1-692-832-11 SWITCH, PUSH (1 KEY) (B PLAY)
S1003 1-572-248-11 SWITCH, LEAF (A HALF) C214 1-136-171-00 FILM 0.33uF 5% 50V
S1004 1-571-281-21 SWITCH, LEAF (A CrO2) C215 1-162-294-31 CERAMIC 0.001uF 10% 50V
S1005 1-571-281-21 SWITCH, LEAF (REC A) C216 1-136-167-00 FILM 0.15uF 5% 50V
C221 1-126-967-11 ELECT 47uF 20% 10V
S1006 1-572-248-11 SWITCH, LEAF (B HALF) C222 1-126-967-11 ELECT 47uF 20% 10V
S1008 1-571-281-21 SWITCH, LEAF (B CrO2)
S1009 1-571-281-21 SWITCH, LEAF (REC B) C223 1-126-964-11 ELECT 10uF 20% 50V
************************************************************ C224 1-162-290-31 CERAMIC 470PF 10% 50V
C226 1-126-964-11 ELECT 10uF 20% 50V
* 1-664-017-11 LED BOARD C227 1-164-159-21 CERAMIC 0.1uF 50V
********* C231 1-126-960-11 ELECT 1uF 20% 50V

< CONNECTOR > C251 1-136-167-00 FILM 0.15uF 5% 50V

C252 1-136-167-00 FILM 0.15uF 5% 50V
CN671 1-506-481-11 PIN, CONNECTOR 2P C253 1-130-493-00 MYLAR 0.068uF 5% 50V
C254 1-130-493-00 MYLAR 0.068uF 5% 50V
< DIODE > C255 1-130-486-00 MYLAR 0.018uF 10% 50V

D671 8-719-058-03 DIODE SEL5423E-TP15 C256 1-130-486-00 MYLAR 0.018uF 10% 50V
D672 8-719-058-03 DIODE SEL5423E-TP15 C257 1-130-480-00 MYLAR 0.0056uF 5% 50V
D673 8-719-058-03 DIODE SEL5423E-TP15 C258 1-130-479-00 MYLAR 0.0047uF 5% 50V
D674 8-719-058-03 DIODE SEL5423E-TP15 C259 1-130-474-00 MYLAR 0.0018uF 5% 50V
C260 1-126-964-11 ELECT 10uF 20% 50V
< RESISTOR >
C261 1-126-964-11 ELECT 10uF 20% 50V
R791 1-249-412-11 CARBON 390 5% 1/4W C262 1-130-483-00 MYLAR 0.01uF 5% 50V
************************************************************ C263 1-136-171-00 FILM 0.33uF 5% 50V
C264 1-136-171-00 FILM 0.33uF 5% 50V
* A-4392-469-A MAIN BOARD, COMPLETE C276 1-126-964-11 ELECT 10uF 20% 50V
*********************
C281 1-126-933-11 ELECT 100uF 20% 10V
* 4-870-539-11 PLATE, GROUND C282 1-126-961-11 ELECT 2.2uF 20% 50V
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S C283 1-126-933-11 ELECT 100uF 20% 10V
C284 1-126-923-11 ELECT 220uF 20% 10V
< CAPACITOR > C291 1-126-959-11 ELECT 0.47uF 20% 50V

C102 1-162-282-31 CERAMIC 100PF 10% 50V C301 1-126-967-11 ELECT 47uF 20% 10V
C103 1-162-282-31 CERAMIC 100PF 10% 50V C302 1-164-159-21 CERAMIC 0.1uF 50V
C104 1-126-962-11 ELECT 3.3uF 20% 50V C303 1-136-165-00 FILM 0.1uF 5% 50V
C105 1-162-600-11 CERAMIC 0.0047uF 30% 16V C304 1-126-926-11 ELECT 1000uF 20% 10V
C106 1-162-301-11 CERAMIC 0.0015uF 30% 16V C305 1-162-306-11 CERAMIC 0.01uF 20% 16V

C107 1-126-956-91 ELECT 0.1uF 20% 50V C309 1-102-514-11 CERAMIC 22PF 5% 50V
C121 1-162-286-21 CERAMIC 220PF 10% 50V C310 1-102-514-11 CERAMIC 22PF 5% 50V
C123 1-162-306-11 CERAMIC 0.01uF 20% 16V C311 1-164-159-21 CERAMIC 0.1uF 50V

– 107 –
 MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C315 1-126-933-11 ELECT 100uF 20% 10V < DIODE >
C390 1-126-933-11 ELECT 100uF 20% 10V
D141 8-719-987-63 DIODE 1N4148M
C393 1-126-925-11 ELECT 470uF 20% 10V D281 8-719-815-85 DIODE 1S1585
C394 1-164-159-21 CERAMIC 0.1uF 50V D291 8-719-987-63 DIODE 1N4148M
C396 1-126-961-11 ELECT 2.2uF 20% 50V D301 8-719-200-82 DIODE 11ES2
C398 1-126-961-11 ELECT 2.2uF 20% 50V D302 8-719-200-82 DIODE 11ES2
C903 1-136-165-00 FILM 0.1uF 5% 50V
D303 8-719-987-63 DIODE 1N4148M
C904 1-126-937-11 ELECT 4700uF 20% 16V D304 8-719-987-63 DIODE 1N4148M
C906 1-126-933-11 ELECT 100uF 20% 10V D305 8-719-987-63 DIODE 1N4148M
C909 1-126-964-11 ELECT 10uF 20% 50V D306 8-719-987-63 DIODE 1N4148M
C910 1-126-933-11 ELECT 100uF 20% 10V D307 8-719-987-63 DIODE 1N4148M
C911 1-126-964-11 ELECT 10uF 20% 50V
D309 8-719-987-63 DIODE 1N4148M
C912 1-126-916-11 ELECT 1000uF 20% 6.3V D902 8-719-200-82 DIODE 11ES2
C913 1-126-943-11 ELECT 2200uF 20% 25V D903 8-719-200-82 DIODE 11ES2
C914 1-126-767-11 ELECT 1000uF 20% 16V D904 8-719-200-82 DIODE 11ES2
C915 1-126-967-11 ELECT 47uF 20% 16V D905 8-719-200-82 DIODE 11ES2
C916 1-164-159-21 CERAMIC 0.1uF 50V
D906 8-719-200-82 DIODE 11ES2
C917 1-126-968-11 ELECT 100uF 20% 50V D907 8-719-200-82 DIODE 11ES2
C918 1-126-968-11 ELECT 100uF 20% 50V D908 8-719-200-82 DIODE 11ES2
C919 1-126-964-11 ELECT 10uF 20% 50V D909 8-719-200-82 DIODE 11ES2
C920 1-126-947-11 ELECT 47uF 20% 35V D910 8-719-012-45 DIODE UZ-33BSC-TA
C953 1-136-165-00 FILM 0.1uF 5% 50V
D911 8-719-010-43 DIODE UZ-5.6BSC
C954 1-126-768-11 ELECT 2200uF 20% 16V D912 8-719-987-63 DIODE 1N4148M
C956 1-126-933-11 ELECT 100uF 20% 10V D913 8-719-200-82 DIODE 11ES2
C1501 1-130-479-00 MYLAR 0.0047uF 5% 50V D914 8-719-200-82 DIODE 11ES2
C1502 1-162-290-31 CERAMIC 470PF 10% 50V D915 8-719-001-43 DIODE UZL-11M1-TA
C1503 1-164-159-21 CERAMIC 0.1uF 50V
D951 8-719-987-63 DIODE 1N4148M
C1504 1-126-960-11 ELECT 1uF 20% 50V D952 8-719-987-63 DIODE 1N4148M
C1505 1-126-964-11 ELECT 10uF 20% 50V
C1506 1-126-964-11 ELECT 10uF 20% 50V < FERRITE BEAD >
C1507 1-126-960-11 ELECT 1uF 20% 50V
C1508 1-126-933-11 ELECT 100uF 20% 10V FB301 1-412-473-21 INDUCTOR 0UH

C1522 1-126-964-11 ELECT 10uF 20% 50V < IC >

C1523 1-126-933-11 ELECT 100uF 20% 16V
C1531 1-164-159-21 CERAMIC 0.1uF 50V IC101 8-759-634-50 IC M5218AL
C1532 1-164-159-21 CERAMIC 0.1uF 50V IC102 8-759-000-48 IC MC14052BCP
C1533 1-164-159-21 CERAMIC 0.1uF 50V IC201 8-759-460-02 IC M62427FP-A
IC231 8-759-634-50 IC M5218AL
C1534 1-126-935-11 ELECT 470uF 20% 16V IC281 8-759-111-68 IC uPC1237HA
C1551 1-130-479-00 MYLAR 0.0047uF 5% 50V
C1552 1-162-290-31 CERAMIC 470PF 10% 50V IC301 8-759-468-71 IC uPD780018YGF-019-3BA
C1553 1-164-159-21 CERAMIC 0.1uF 50V IC302 8-759-635-63 IC M51943BSL
C1554 1-126-960-11 ELECT 1uF 20% 50V IC901 8-759-288-53 IC LA5617
IC902 8-759-604-86 IC M5F7807L
C1555 1-126-964-11 ELECT 10uF 20% 50V IC903 8-759-231-53 IC TA7805S
C1556 1-126-964-11 ELECT 10uF 20% 50V
C1557 1-126-960-11 ELECT 1uF 20% 50V IC904 8-759-231-58 IC TA7812S
C1558 1-126-933-11 ELECT 100uF 20% 10V IC1501 8-759-363-21 IC HA12203NT
IC1502 8-759-822-09 IC LB1641
< CONNECTOR >
< JACK >
CN101 1-778-982-11 CONNECTOR, BOARD TO BOARD 13P
* CN102 1-568-836-11 SOCKET, CONNECTOR 17P J101 1-695-188-31 JACK, PIN 4P (IN PHONO, VIDEO(AUDIO))
* CN201 1-568-832-11 SOCKET, CONNECTOR 13P
CN202 1-568-802-11 SOCKET, CONNECTOR 19P < COIL >
* CN203 1-568-936-11 PIN, CONNECTOR 9P
L301 1-410-509-11 INDUCTOR 10uH
CN205 1-568-838-11 SOCKET, CONNECTOR 21P L393 1-410-515-11 INDUCTOR 33uH
* CN206 1-568-830-11 SOCKET, CONNECTOR 11P
* CN207 1-568-449-11 HOUSING, CONNECTOR(PC BOARD)3P < TRANSISTOR >

Q141 8-729-140-82 TRANSISTOR 2SA988-PAFAEA

Q142 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
Q201 8-729-900-36 TRANSISTOR DTC124ES

– 108 –
 MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
Q202 8-729-119-78 TRANSISTOR 2SC403SP-51 R206 1-249-421-11 CARBON 2.2K 5% 1/4W
Q203 8-729-119-78 TRANSISTOR 2SC403SP-51 R207 1-249-431-11 CARBON 15K 5% 1/4W
R209 1-249-441-11 CARBON 100K 5% 1/4W
Q204 8-729-141-30 TRANSISTOR 2SC3623A-LK R210 1-247-887-00 CARBON 220K 5% 1/4W
Q231 8-729-900-63 TRANSISTOR DTA124ES R211 1-247-891-00 CARBON 330K 5% 1/4W
Q232 8-729-900-63 TRANSISTOR DTA124ES
Q251 8-729-900-36 TRANSISTOR DTC124ES R212 1-249-411-11 CARBON 330 5% 1/4W
Q252 8-729-119-78 TRANSISTOR 2SC403SP-51 R213 1-249-429-11 CARBON 10K 5% 1/4W
R214 1-249-437-11 CARBON 47K 5% 1/4W
Q253 8-729-119-78 TRANSISTOR 2SC403SP-51 R215 1-247-903-00 CARBON 1M 5% 1/4W
Q254 8-729-141-30 TRANSISTOR 2SC3623A-LK R216 1-249-429-11 CARBON 10K 5% 1/4W
Q281 8-729-900-36 TRANSISTOR DTC124ES
Q282 8-729-900-63 TRANSISTOR DTA124ES R217 1-249-437-11 CARBON 47K 5% 1/4W
Q283 8-729-900-36 TRANSISTOR DTC124ES R222 1-249-425-11 CARBON 4.7K 5% 1/4W
R226 1-249-421-11 CARBON 2.2K 5% 1/4W
Q301 8-729-119-78 TRANSISTOR 2SC403SP-51 R227 1-249-441-11 CARBON 100K 5% 1/4W
Q901 8-729-040-20 TRANSISTOR RT1P137L-TP R228 1-249-429-11 CARBON 10K 5% 1/4W
Q902 8-729-900-36 TRANSISTOR DTC124ES
Q903 8-729-030-18 TRANSISTOR 2SD2525 R231 1-249-437-11 CARBON 47K 5% 1/4W
Q904 8-729-030-19 TRANSISTOR 2SB1640 R232 1-249-437-11 CARBON 47K 5% 1/4W
R234 1-247-886-11 CARBON 200K 5% 1/4W
Q905 8-729-040-20 TRANSISTOR RT1P137L-TP R235 1-249-421-11 CARBON 2.2K 5% 1/4W
Q906 8-729-900-63 TRANSISTOR DTA124ES R236 1-249-441-11 CARBON 100K 5% 1/4W
Q907 8-729-119-78 TRANSISTOR 2SC403SP-51
Q1531 8-729-801-93 TRANSISTOR 2SD1387 R253 1-249-441-11 CARBON 100K 5% 1/4W
Q1532 8-729-900-80 TRANSISTOR DTC114ES R257 1-249-431-11 CARBON 15K 5% 1/4W
R259 1-249-441-11 CARBON 100K 5% 1/4W
Q1533 8-729-900-80 TRANSISTOR DTC114ES R260 1-247-887-00 CARBON 220K 5% 1/4W
Q1534 8-729-119-77 TRANSISTOR 2SA1175-FEK R261 1-247-891-00 CARBON 330K 5% 1/4W
Q1535 8-729-900-80 TRANSISTOR DTC114ES
R262 1-249-411-11 CARBON 330 5% 1/4W
< RESISTOR > R263 1-249-429-11 CARBON 10K 5% 1/4W
R264 1-249-437-11 CARBON 47K 5% 1/4W
R102 1-249-417-11 CARBON 1K 5% 1/4W R265 1-247-903-00 CARBON 1M 5% 1/4W
R103 1-249-437-11 CARBON 47K 5% 1/4W R266 1-249-429-11 CARBON 10K 5% 1/4W
R104 1-249-417-11 CARBON 1K 5% 1/4W
R105 1-247-897-11 CARBON 560K 5% 1/4W R267 1-249-437-11 CARBON 47K 5% 1/4W
R106 1-249-437-11 CARBON 47K 5% 1/4W R272 1-249-425-11 CARBON 4.7K 5% 1/4W
R276 1-249-421-11 CARBON 2.2K 5% 1/4W
R107 1-249-417-11 CARBON 1K 5% 1/4W R277 1-249-441-11 CARBON 100K 5% 1/4W
R108 1-249-441-11 CARBON 100K 5% 1/4W R278 1-249-429-11 CARBON 10K 5% 1/4W
R121 1-249-424-11 CARBON 3.9K 5% 1/4W
R122 1-247-887-00 CARBON 220K 5% 1/4W R281 1-249-429-11 CARBON 10K 5% 1/4W
R133 1-260-091-11 CARBON 220 5% 1/2W R282 1-249-429-11 CARBON 10K 5% 1/4W
R283 1-249-435-11 CARBON 33K 5% 1/4W
R134 1-260-091-11 CARBON 220 5% 1/2W R284 1-247-791-91 CARBON 22 5% 1/4W
R140 1-249-429-11 CARBON 10K 5% 1/4W R285 1-249-441-11 CARBON 100K 5% 1/4W
R141 1-249-437-11 CARBON 47K 5% 1/4W
R142 1-249-429-11 CARBON 10K 5% 1/4W R286 1-249-429-11 CARBON 10K 5% 1/4W
! R147 1-215-893-11 METAL OXIDE 1.5K 5% 2W F R287 1-249-429-11 CARBON 10K 5% 1/4W
R288 1-249-438-11 CARBON 56K 5% 1/4W
R152 1-249-417-11 CARBON 1K 5% 1/4W R289 1-249-437-11 CARBON 47K 5% 1/4W
R153 1-249-437-11 CARBON 47K 5% 1/4W R291 1-247-863-91 CARBON 22K 5% 1/4W
R154 1-249-417-11 CARBON 1K 5% 1/4W
R155 1-247-897-11 CARBON 560K 5% 1/4W R292 1-247-863-91 CARBON 22K 5% 1/4W
R156 1-249-437-11 CARBON 47K 5% 1/4W R293 1-249-416-11 CARBON 820 5% 1/4W
R294 1-249-441-11 CARBON 100K 5% 1/4W
R157 1-249-417-11 CARBON 1K 5% 1/4W R295 1-247-903-00 CARBON 1M 5% 1/4W
R158 1-249-441-11 CARBON 100K 5% 1/4W R301 1-249-413-11 CARBON 470 5% 1/4W
R171 1-249-424-11 CARBON 3.9K 5% 1/4W
R172 1-247-887-00 CARBON 220K 5% 1/4W R302 1-249-425-11 CARBON 4.7K 5% 1/4W
R183 1-260-091-11 CARBON 220 5% 1/2W R303 1-249-437-11 CARBON 47K 5% 1/4W
R304 1-249-437-11 CARBON 47K 5% 1/4W
R184 1-260-091-11 CARBON 220 5% 1/2W R305 1-249-429-11 CARBON 10K 5% 1/4W
R201 1-249-429-11 CARBON 10K 5% 1/4W R311 1-247-807-31 CARBON 100 5% 1/4W
R202 1-247-863-91 CARBON 22K 5% 1/4W
R203 1-249-441-11 CARBON 100K 5% 1/4W R312 1-247-807-31 CARBON 100 5% 1/4W
R205 1-247-863-91 CARBON 22K 5% 1/4W R313 1-247-807-31 CARBON 100 5% 1/4W

The components identified by mark

! or dotted line with mark ! are
critical for safety.
Replace only with part number
specified.
– 109 –
 MAIN PANEL
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R316 1-249-429-11 CARBON 10K 5% 1/4W R1507 1-249-428-11 CARBON 8.2K 5% 1/4W
R318 1-249-429-11 CARBON 10K 5% 1/4W R1521 1-249-430-11 CARBON 12K 5% 1/4W
R319 1-249-429-11 CARBON 10K 5% 1/4W R1522 1-249-426-11 CARBON 5.6K 5% 1/4W
R1524 1-249-429-11 CARBON 10K 5% 1/4W
R320 1-249-429-11 CARBON 10K 5% 1/4W
R322 1-249-425-11 CARBON 4.7K 5% 1/4W R1525 1-249-432-11 CARBON 18K 5% 1/4W
R323 1-247-807-31 CARBON 100 5% 1/4W R1526 1-249-429-11 CARBON 10K 5% 1/4W
R325 1-249-431-11 CARBON 15K 5% 1/4W R1527 1-249-429-11 CARBON 10K 5% 1/4W
R326 1-249-415-11 CARBON 680 5% 1/4W R1531 1-247-843-11 CARBON 3.3K 5% 1/4W
R1532 1-249-411-11 CARBON 330 5% 1/4W
R327 1-247-807-31 CARBON 100 5% 1/4W
R328 1-247-807-31 CARBON 100 5% 1/4W R1533 1-249-427-11 CARBON 6.8K 5% 1/4W
R330 1-247-807-31 CARBON 100 5% 1/4W R1534 1-249-429-11 CARBON 10K 5% 1/4W
R331 1-247-807-31 CARBON 100 5% 1/4W R1535 1-249-425-11 CARBON 4.7K 5% 1/4W
R332 1-247-807-31 CARBON 100 5% 1/4W R1536 1-249-425-11 CARBON 4.7K 5% 1/4W
R1541 1-249-425-11 CARBON 4.7K 5% 1/4W
R333 1-247-807-31 CARBON 100 5% 1/4W
R339 1-247-807-31 CARBON 100 5% 1/4W R1542 1-249-425-11 CARBON 4.7K 5% 1/4W
R340 1-247-807-31 CARBON 100 5% 1/4W R1543 1-249-425-11 CARBON 4.7K 5% 1/4W
R341 1-247-807-31 CARBON 100 5% 1/4W R1544 1-249-417-11 CARBON 1K 5% 1/4W
R342 1-247-807-31 CARBON 100 5% 1/4W R1545 1-249-437-11 CARBON 47K 5% 1/4W
R1546 1-249-437-11 CARBON 47K 5% 1/4W
R344 1-247-807-31 CARBON 100 5% 1/4W
R345 1-247-807-31 CARBON 100 5% 1/4W R1547 1-249-437-11 CARBON 47K 5% 1/4W
R346 1-247-807-31 CARBON 100 5% 1/4W R1548 1-249-437-11 CARBON 47K 5% 1/4W
R349 1-247-807-31 CARBON 100 5% 1/4W R1551 1-247-863-91 CARBON 22K 5% 1/4W
R350 1-247-807-31 CARBON 100 5% 1/4W R1552 1-249-417-11 CARBON 1K 5% 1/4W
R1553 1-249-426-11 CARBON 5.6K 5% 1/4W
R351 1-247-807-31 CARBON 100 5% 1/4W
R352 1-247-807-31 CARBON 100 5% 1/4W R1554 1-247-840-00 CARBON 2.4K 5% 1/4W
R353 1-247-807-31 CARBON 100 5% 1/4W R1555 1-247-863-91 CARBON 22K 5% 1/4W
R354 1-247-807-31 CARBON 100 5% 1/4W R1556 1-249-421-11 CARBON 2.2K 5% 1/4W
R355 1-247-807-31 CARBON 100 5% 1/4W R1557 1-249-428-11 CARBON 8.2K 5% 1/4W

R356 1-247-807-31 CARBON 100 5% 1/4W < VARIABLE RESISTOR >

R357 1-247-807-31 CARBON 100 5% 1/4W
R359 1-247-807-31 CARBON 100 5% 1/4W RV1501 1-238-598-11 RES, ADJ, CARBON 2.2K
R360 1-247-807-31 CARBON 100 5% 1/4W RV1551 1-238-598-11 RES, ADJ, CARBON 2.2K
R366 1-247-807-31 CARBON 100 5% 1/4W
< RELAY >
R367 1-249-429-11 CARBON 10K 5% 1/4W
R368 1-247-843-11 CARBON 3.3K 5% 1/4W RY141 1-755-141-11 RELAY
R369 1-249-429-11 CARBON 10K 5% 1/4W
R381 1-247-807-31 CARBON 100 5% 1/4W < TERMINAL >
R384 1-249-429-11 CARBON 10K 5% 1/4W
TM131 1-537-240-31 TERMINAL BOARD (CHECKER PIN)
R395 1-247-807-31 CARBON 100 5% 1/4W (SPEAKER)
R396 1-249-435-11 CARBON 33K 5% 1/4W TM132 1-537-240-31 TERMINAL BOARD (CHECKER PIN)
R397 1-247-807-31 CARBON 100 5% 1/4W (SURROUND)
R398 1-249-435-11 CARBON 33K 5% 1/4W
R417 1-249-441-11 CARBON 100K 5% 1/4W < VIBRATOR >

R913 1-247-815-91 CARBON 220 5% 1/4W X301 1-760-489-11 VIBRATOR, CERAMIC (5MHz)
R914 1-249-417-11 CARBON 1K 5% 1/4W X302 1-567-098-41 VIBRATOR, CRYSTAL (32.768KHz)
R915 1-249-425-11 CARBON 4.7K 5% 1/4W ************************************************************
R916 1-247-815-91 CARBON 220 5% 1/4W
R917 1-247-815-91 CARBON 220 5% 1/4W * A-4392-472-A PANEL BOARD, COMPLETE
**********************
R918 1-249-425-11 CARBON 4.7K 5% 1/4W
R920 1-249-417-11 CARBON 1K 5% 1/4W * 4-986-870-11 HOLDER, FL TUBE
R921 1-247-895-91 CARBON 470K 5% 1/4W
R951 1-249-425-11 CARBON 4.7K 5% 1/4W < CAPACITOR
R952 1-249-425-11 CARBON 4.7K 5% 1/4W
C601 1-126-967-11 ELECT 47uF 20% 50V
R1501 1-249-435-11 CARBON 33K 5% 1/4W C602 1-162-306-11 CERAMIC 0.01uF 20% 16V
R1502 1-249-417-11 CARBON 1K 5% 1/4W C603 1-126-963-11 ELECT 4.7uF 20% 50V
R1503 1-249-426-11 CARBON 5.6K 5% 1/4W C604 1-126-960-11 ELECT 1uF 20% 50V
R1504 1-247-840-00 CARBON 2.4K 5% 1/4W C606 1-126-960-11 ELECT 1uF 20% 50V
R1505 1-247-863-91 CARBON 22K 5% 1/4W
C608 1-124-584-00 ELECT 100uF 20% 10V
R1506 1-249-421-11 CARBON 2.2K 5% 1/4W C610 1-162-306-11 CERAMIC 0.01uF 20% 16V

– 110 –
 PANEL

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C611 1-162-306-11 CERAMIC 0.01uF 20% 16V D621 8-719-058-04 DIODE SEL5223S-TP15 (FILE 4)
C612 1-126-967-11 ELECT 47uF 20% 50V D622 8-719-058-04 DIODE SEL5223S-TP15 (FILE 5)
C613 1-164-159-21 CERAMIC 0.1uF 50V D623 8-719-058-04 DIODE SEL5223S-TP15 (P.FILE)

C621 1-126-960-11 ELECT 1uF 20% 50V D624 8-719-058-04 DIODE SEL5223S-TP15 (MENU 2)
C622 1-136-161-00 FILM 0.047uF 5% 50V D625 8-719-058-04 DIODE SEL5223S-TP15 (MENU 1)
C623 1-126-957-11 ELECT 0.22uF 20% 50V D628 8-719-058-04 DIODE SEL5223S-TP15 (KEY CONTROL)
C624 1-126-957-11 ELECT 0.22uF 20% 50V
C625 1-162-306-11 CERAMIC 0.01uF 20% 16V < FERRITE BEAD >

C626 1-126-957-11 ELECT 0.22uF 20% 50V FB601 1-412-473-21 INDUCTOR 0UH
C627 1-136-159-00 FILM 0.033uF 5% 50V
C628 1-162-302-11 CERAMIC 0.0022uF 30% 16V < FILTER >
C629 1-126-957-11 ELECT 0.22uF 20% 50V
C630 1-162-293-31 CERAMIC 820PF 10% 50V FL601 1-517-617-11 INDICATOR TUBE, FLUORESCENT

C631 1-126-957-11 ELECT 0.22uF 20% 50V < IC >

C632 1-126-957-11 ELECT 0.22uF 20% 50V
C641 1-162-286-21 CERAMIC 220PF 10% 50V IC601 8-759-462-83 IC TMP87CM75F-6542
C642 1-162-286-21 CERAMIC 220PF 10% 50V IC602 8-759-459-84 IC NJL56H400
C643 1-162-286-21 CERAMIC 220PF 10% 50V
< COIL >
C644 1-162-286-21 CERAMIC 220PF 10% 50V
C645 1-162-286-21 CERAMIC 220PF 10% 50V L601 1-410-509-11 INDUCTOR 10uH
C646 1-162-286-21 CERAMIC 220PF 10% 50V
C647 1-162-286-21 CERAMIC 220PF 10% 50V < TRANSISTOR >
C648 1-162-286-21 CERAMIC 220PF 10% 50V
Q601 8-729-119-78 TRANSISTOR 2SC403SP-51
C649 1-162-286-21 CERAMIC 220PF 10% 50V Q602 8-729-118-00 TRANSISTOR 2SB1116-L
C650 1-162-286-21 CERAMIC 220PF 10% 50V Q603 8-729-118-00 TRANSISTOR 2SB1116-L
C651 1-162-286-21 CERAMIC 220PF 10% 50V Q604 8-729-119-77 TRANSISTOR 2SA1175-FEK
C652 1-162-286-21 CERAMIC 220PF 10% 50V Q605 8-729-119-77 TRANSISTOR 2SA1175-FEK
C653 1-162-286-21 CERAMIC 220PF 10% 50V
Q606 8-729-119-77 TRANSISTOR 2SA1175-FEK
C654 1-162-286-21 CERAMIC 220PF 10% 50V Q607 8-729-119-77 TRANSISTOR 2SA1175-FEK
C655 1-162-286-21 CERAMIC 220PF 10% 50V Q608 8-729-119-77 TRANSISTOR 2SA1175-FEK
C656 1-162-286-21 CERAMIC 220PF 10% 50V Q609 8-729-119-77 TRANSISTOR 2SA1175-FEK
C695 1-164-159-21 CERAMIC 0.1uF 50V Q610 8-729-119-77 TRANSISTOR 2SA1175-FEK
C696 1-164-159-21 CERAMIC 0.1uF 50V
Q611 8-729-119-77 TRANSISTOR 2SA1175-FEK
C697 1-162-294-31 CERAMIC 0.001uF 10% 50V Q613 8-729-119-77 TRANSISTOR 2SA1175-FEK
Q614 8-729-119-77 TRANSISTOR 2SA1175-FEK
< CONNECTOR > Q615 8-729-119-77 TRANSISTOR 2SA1175-FEK
Q617 8-729-119-77 TRANSISTOR 2SA1175-FEK
* CN601 1-568-836-11 SOCKET, CONNECTOR 17P
* CN602 1-568-947-11 PIN, CONNECTOR 9P Q618 8-729-119-77 TRANSISTOR 2SA1175-FEK
CN603 1-506-486-11 PIN, CONNECTOR 7P Q619 8-729-119-77 TRANSISTOR 2SA1175-FEK
* CN604 1-568-947-11 PIN, CONNECTOR 9P Q621 8-729-119-77 TRANSISTOR 2SA1175-FEK
Q622 8-729-119-77 TRANSISTOR 2SA1175-FEK
< DIODE >
< RESISTOR >
D601 8-719-987-63 DIODE 1N4148M
D602 8-719-987-63 DIODE 1N4148M R601 1-249-427-11 CARBON 6.8K 5% 1/4W
D603 8-719-987-63 DIODE 1N4148M R602 1-249-435-11 CARBON 33K 5% 1/4W
D604 8-719-987-63 DIODE 1N4148M R603 1-247-903-00 CARBON 1M 5% 1/4W
D605 8-719-987-63 DIODE 1N4148M R606 1-249-429-11 CARBON 10K 5% 1/4W
R607 1-249-429-11 CARBON 10K 5% 1/4W
D606 8-719-987-63 DIODE 1N4148M
D607 8-719-987-63 DIODE 1N4148M R608 1-249-429-11 CARBON 10K 5% 1/4W
D611 8-719-057-29 DIODE SML78423C-TP15 (TUNER/BAND) R609 1-249-429-11 CARBON 10K 5% 1/4W
D612 8-719-057-29 DIODE SML78423C-TP15 (TUNER/BAND) R610 1-249-429-11 CARBON 10K 5% 1/4W
D613 8-719-058-04 DIODE SEL5223S-TP15 (ENTER/NEXT) R611 1-247-843-11 CARBON 3.3K 5% 1/4W
R612 1-247-843-11 CARBON 3.3K 5% 1/4W
D614 8-719-058-04 DIODE SEL5223S-TP15 (GROOVE)
D615 8-719-058-04 DIODE SEL5223S-TP15 (SUPER WOOFER) R613 1-249-401-11 CARBON 47 5% 1/4W
D616 8-719-058-04 DIODE SEL5223S-TP15 (EFFECT) R614 1-249-429-11 CARBON 10K 5% 1/4W
D617 8-719-058-04 DIODE SEL5223S-TP15 (ENTER) R615 1-249-429-11 CARBON 10K 5% 1/4W
D618 8-719-058-04 DIODE SEL5223S-TP15 (FILE 1) R617 1-249-429-11 CARBON 10K 5% 1/4W
R621 1-249-421-11 CARBON 2.2K 5% 1/4W
D619 8-719-058-04 DIODE SEL5223S-TP15 (FILE 2)
D620 8-719-058-04 DIODE SEL5223S-TP15 (FILE 3) R622 1-249-437-11 CARBON 47K 5% 1/4W

– 111 –
 PANEL
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R623 1-247-895-91 CARBON 470K 5% 1/4W R686 1-247-807-31 CARBON 100 5% 1/4W
R624 1-249-421-11 CARBON 2.2K 5% 1/4W R687 1-247-807-31 CARBON 100 5% 1/4W
R625 1-249-437-11 CARBON 47K 5% 1/4W R688 1-247-807-31 CARBON 100 5% 1/4W
R626 1-247-895-91 CARBON 470K 5% 1/4W R689 1-247-807-31 CARBON 100 5% 1/4W
R690 1-247-807-31 CARBON 100 5% 1/4W
R627 1-249-421-11 CARBON 2.2K 5% 1/4W
R628 1-249-437-11 CARBON 47K 5% 1/4W R691 1-247-807-31 CARBON 100 5% 1/4W
R629 1-247-895-91 CARBON 470K 5% 1/4W R692 1-247-807-31 CARBON 100 5% 1/4W
R631 1-249-437-11 CARBON 47K 5% 1/4W R693 1-247-807-31 CARBON 100 5% 1/4W
R632 1-247-895-91 CARBON 470K 5% 1/4W R694 1-247-807-31 CARBON 100 5% 1/4W
R695 1-247-807-31 CARBON 100 5% 1/4W
R633 1-247-897-11 CARBON 560K 5% 1/4W
R634 1-247-897-11 CARBON 560K 5% 1/4W R696 1-247-807-31 CARBON 100 5% 1/4W
R635 1-247-897-11 CARBON 560K 5% 1/4W R697 1-247-807-31 CARBON 100 5% 1/4W
R636 1-247-897-11 CARBON 560K 5% 1/4W R698 1-247-807-31 CARBON 100 5% 1/4W
R637 1-247-895-91 CARBON 470K 5% 1/4W R699 1-247-807-31 CARBON 100 5% 1/4W
R700 1-247-807-31 CARBON 100 5% 1/4W
R638 1-249-435-11 CARBON 33K 5% 1/4W
R641 1-249-419-11 CARBON 1.5K 5% 1/4W R703 1-247-807-31 CARBON 100 5% 1/4W
R642 1-249-401-11 CARBON 47 5% 1/4W
R643 1-249-403-11 CARBON 68 5% 1/4W < SWITCH >
R644 1-247-807-31 CARBON 100 5% 1/4W
S601 1-554-303-21 SWITCH, TACTILE (ENTER/NEXT)
R645 1-249-407-11 CARBON 150 5% 1/4W S602 1-554-303-21 SWITCH, TACTILE (TUNER MEMORY)
R646 1-249-407-11 CARBON 150 5% 1/4W S603 1-554-303-21 SWITCH, TACTILE (TUNING MODE)
R647 1-247-815-91 CARBON 220 5% 1/4W S604 1-554-303-21 SWITCH, TACTILE (TUNER/BAND)
R648 1-249-411-11 CARBON 330 5% 1/4W S605 1-554-303-21 SWITCH, TACTILE (TUNING +)
R649 1-249-413-11 CARBON 470 5% 1/4W
S606 1-554-303-21 SWITCH, TACTILE (TUNING –)
R650 1-249-415-11 CARBON 680 5% 1/4W S607 1-554-303-21 SWITCH, TACTILE (STEREO/MONO)
R651 1-249-417-11 CARBON 1K 5% 1/4W S609 1-554-303-21 SWITCH, TACTILE (FUNCTION)
R652 1-249-419-11 CARBON 1.5K 5% 1/4W S610 1-554-303-21 SWITCH, TACTILE (GROOVE)
R653 1-249-421-11 CARBON 2.2K 5% 1/4W S611 1-554-303-21 SWITCH, TACTILE (GEQ ¢)
R654 1-247-843-11 CARBON 3.3K 5% 1/4W
S612 1-554-303-21 SWITCH, TACTILE (GEQ ª)
R655 1-249-427-11 CARBON 6.8K 5% 1/4W S613 1-554-303-21 SWITCH, TACTILE (GEQ ·)
R656 1-249-431-11 CARBON 15K 5% 1/4W S614 1-554-303-21 SWITCH, TACTILE (GEQ ›)
R657 1-249-419-11 CARBON 1.5K 5% 1/4W S615 1-554-303-21 SWITCH, TACTILE (SUPER WOOFER)
R658 1-249-401-11 CARBON 47 5% 1/4W S616 1-554-303-21 SWITCH, TACTILE (S/W MODE)
R659 1-249-403-11 CARBON 68 5% 1/4W
S617 1-554-303-21 SWITCH, TACTILE (N)
R660 1-247-807-31 CARBON 100 5% 1/4W S618 1-554-303-21 SWITCH, TACTILE (˜)
R661 1-249-407-11 CARBON 150 5% 1/4W S619 1-554-303-21 SWITCH, TACTILE (GEQ CONTROL)
R662 1-249-407-11 CARBON 150 5% 1/4W S620 1-554-303-21 SWITCH, TACTILE (ENTER)
R663 1-249-419-11 CARBON 1.5K 5% 1/4W S621 1-554-303-21 SWITCH, TACTILE (EFFECT)
R664 1-249-401-11 CARBON 47 5% 1/4W
S622 1-554-303-21 SWITCH, TACTILE (WAVE)
R665 1-249-403-11 CARBON 68 5% 1/4W S623 1-554-303-21 SWITCH, TACTILE (KARAOKE PON/MPX)
R666 1-247-807-31 CARBON 100 5% 1/4W S624 1-554-303-21 SWITCH, TACTILE (SURROUND)
R667 1-249-407-11 CARBON 150 5% 1/4W S625 1-554-303-21 SWITCH, TACTILE (P. FILE MEMORY)
R668 1-249-407-11 CARBON 150 5% 1/4W S627 1-554-303-21 SWITCH, TACTILE (SPECTRUM ANALYZER)
R669 1-249-419-11 CARBON 1.5K 5% 1/4W
S628 1-554-303-21 SWITCH, TACTILE (DISPLAY/DEMO)
R670 1-249-401-11 CARBON 47 5% 1/4W S629 1-554-303-21 SWITCH, TACTILE (POWER)
R671 1-249-403-11 CARBON 68 5% 1/4W S630 1-554-303-21 SWITCH, TACTILE (CLOCK SET)
R672 1-247-807-31 CARBON 100 5% 1/4W S631 1-554-303-21 SWITCH, TACTILE (REC)
R673 1-249-407-11 CARBON 150 5% 1/4W S632 1-554-303-21 SWITCH, TACTILE (DAILY 1)
R674 1-249-407-11 CARBON 150 5% 1/4W
S633 1-554-303-21 SWITCH, TACTILE (DAYLY 2)
R675 1-247-815-91 CARBON 220 5% 1/4W S634 1-554-303-21 SWITCH, TACTILE (SLEEP)
R676 1-249-411-11 CARBON 330 5% 1/4W S701 1-473-392-11 ENCODER, ROTARY (VOLUME)
R677 1-249-413-11 CARBON 470 5% 1/4W
R678 1-249-415-11 CARBON 680 5% 1/4W < VIBRATOR >
R679 1-249-419-11 CARBON 1.5K 5% 1/4W
X601 1-579-125-11 VIBRATOR, CERAMIC (8MHz)
R681 1-249-429-11 CARBON 10K 5% 1/4W ************************************************************
R682 1-249-421-11 CARBON 2.2K 5% 1/4W
R683 1-247-887-00 CARBON 220K 5% 1/4W
R684 1-249-421-11 CARBON 2.2K 5% 1/4W
R685 1-247-815-91 CARBON 220 5% 1/4W

– 112 –
 POWERAMP TABLE SENSOR TC-A SW

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* A-4392-436-A POWERAMP BOARD, COMPLETE R812 1-249-431-11 CARBON 15K 5% 1/4W
***************************** R813 1-249-441-11 CARBON 100K 5% 1/4W
R814 1-260-103-11 CARBON 2.2K 5% 1/2W
< CAPACITOR > R816 1-260-103-11 CARBON 2.2K 5% 1/2W
! R820 1-202-972-61 FUSIBLE 1 5% 1/4W F
C801 1-128-582-11 ELECT 10uF 20% 100V
C802 1-162-286-21 CERAMIC 220PF 10% 50V R841 1-249-425-11 CARBON 4.7K 5% 1/4W
C803 1-162-282-31 CERAMIC 100PF 10% 50V R842 1-247-885-00 CARBON 180K 5% 1/4W
C804 1-126-967-11 ELECT 47uF 20% 50V R843 1-249-421-11 CARBON 2.2K 5% 1/4W
C806 1-126-967-11 ELECT 47uF 20% 50V R844 1-249-429-11 CARBON 10K 5% 1/4W
R851 1-249-417-11 CARBON 1K 5% 1/4W
C807 1-128-560-11 ELECT 22uF 20% 100V
C809 1-128-560-11 ELECT 22uF 20% 100V R852 1-249-437-11 CARBON 47K 5% 1/4W
C810 1-164-159-21 CERAMIC 0.1uF 50V R853 1-249-413-11 CARBON 470 5% 1/4W
C811 1-130-493-00 MYLAR 0.068uF 5% 50V R854 1-249-437-11 CARBON 47K 5% 1/4W
C812 1-130-493-00 MYLAR 0.068uF 5% 50V R855 1-260-107-11 CARBON 4.7K 5% 1/2W
R856 1-260-107-11 CARBON 4.7K 5% 1/2W
C814 1-162-306-11 CERAMIC 0.01uF 20% 16V
C841 1-126-925-11 ELECT 470uF 20% 10V ! R857 1-212-881-11 FUSIBLE 100 5% 1/4W F
C851 1-128-582-11 ELECT 10uF 20% 100V ! R858 1-217-156-00 WIREWOUND 0.22 10% 5W F
C852 1-162-286-21 CERAMIC 220PF 10% 50V R859 1-260-076-11 CARBON 10 5% 1/2W
C853 1-162-282-31 CERAMIC 100PF 10% 50V R861 1-249-417-11 CARBON 1K 5% 1/4W
R862 1-249-431-11 CARBON 15K 5% 1/4W
C854 1-126-967-11 ELECT 47uF 20% 50V
C856 1-126-967-11 ELECT 47uF 20% 50V R863 1-249-441-11 CARBON 100K 5% 1/4W
C857 1-128-560-11 ELECT 22uF 20% 100V ************************************************************
C861 1-130-493-00 MYLAR 0.068uF 5% 50V
C862 1-130-493-00 MYLAR 0.068uF 5% 50V * 1-659-058-13 TABLE SENSOR BOARD
******************
C901 1-104-482-11 ELECT 4700uF 20% 63V
C902 1-130-777-00 FILM 0.1uF 10% 100V < IC >
C951 1-104-482-11 ELECT 4700uF 20% 63V
C952 1-130-777-00 FILM 0.1uF 10% 100V IC202 8-749-924-18 IC PHOTO INTERRUPTER RPI-1391

< CONNECTOR > < RESISTOR >

CN801 1-778-981-11 CONNECTOR, BOARD TO BOARD 13P R207 1-249-416-11 CARBON 820 5% 1/4W
************************************************************
< DIODE >
* 1-664-012-11 TC-A SW BOARD
D801 8-719-815-85 DIODE 1S1585 *************
D841 8-719-987-63 DIODE 1N4148M
D842 8-719-987-63 DIODE 1N4148M < CONNECTOR >
D851 8-719-815-85 DIODE 1S1585
D901 8-719-510-68 DIODE D5SBA20F01 CN612 1-506-486-11 PIN, CONNECTOR 7P

< IC > < DIODE >

IC801 8-749-921-68 IC STK-4231MK2 D631 8-719-057-29 DIODE SML78423C-TP15 (·)

D632 8-719-057-29 DIODE SML78423C-TP15 (ª)
< TRANSISTOR >
< RESISTOR >
Q801 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
Q851 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA R705 1-249-401-11 CARBON 47 5% 1/4W
R706 1-249-403-11 CARBON 68 5% 1/4W
< RESISTOR > R707 1-247-807-31 CARBON 100 5% 1/4W
R708 1-249-407-11 CARBON 150 5% 1/4W
R801 1-249-417-11 CARBON 1K 5% 1/4W R709 1-249-407-11 CARBON 150 5% 1/4W
R802 1-249-437-11 CARBON 47K 5% 1/4W
R803 1-249-413-11 CARBON 470 5% 1/4W R710 1-247-815-91 CARBON 220 5% 1/4W
R804 1-249-437-11 CARBON 47K 5% 1/4W R711 1-247-807-31 CARBON 100 5% 1/4W
R805 1-260-107-11 CARBON 4.7K 5% 1/2W R712 1-247-807-31 CARBON 100 5% 1/4W
R713 1-247-807-31 CARBON 100 5% 1/4W
R806 1-260-107-11 CARBON 4.7K 5% 1/2W R714 1-247-807-31 CARBON 100 5% 1/4W
! R807 1-212-881-11 FUSIBLE 100 5% 1/4W F
! R808 1-217-156-00 WIREWOUND 0.22 10% 5W F < SWITCH >
R809 1-260-076-11 CARBON 10 5% 1/2W
R811 1-249-417-11 CARBON 1K 5% 1/4W S641 1-554-303-21 SWITCH, TACTILE (·)

The components identified by mark

! or dotted line with mark ! are
critical for safety.
Replace only with part number
specified.
– 113 –
 TC-A SW TC-B SW TCB

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
S642 1-554-303-21 SWITCH, TACTILE (ª) C22 1-164-159-21 CERAMIC 0.1uF 50V
S643 1-554-303-21 SWITCH, TACTILE (p) C23 1-162-306-11 CERAMIC 0.01uF 20% 16V
S644 1-554-303-21 SWITCH, TACTILE (0) C24 1-126-967-11 ELECT 47uF 20% 16V
S645 1-554-303-21 SWITCH, TACTILE ())
C25 1-162-306-11 CERAMIC 0.01uF 20% 16V
S646 1-554-303-21 SWITCH, TACTILE (DOLBY NR) C26 1-126-964-11 ELECT 10uF 20% 50v
S647 1-554-303-21 SWITCH, TACTILE (DIRECTION) C27 1-164-159-21 CERAMIC 0.1uF 50V
************************************************************ C28 1-126-961-11 ELECT 2.2uF 20% 50V
C29 1-102-518-11 CERAMIC 33PF 5% 50V
* 1-664-013-11 TC-B SW BOARD
************* C30 1-162-294-31 CERAMIC 0.001uF 10% 50V
C31 1-162-306-11 CERAMIC 0.01uF 20% 16V
< DIODE > C41 1-126-933-11 ELECT 100uF 20% 10V
C42 1-162-306-11 CERAMIC 0.01uF 20% 16V
D635 8-719-057-29 DIODE SML78423C-TP15 (ª) C43 1-126-962-11 ELECT 3.3uF 20% 50V
D636 8-719-057-29 DIODE SML78423C-TP15 (·)
D637 8-719-058-17 DIODE LNG401NPYJA (P) C44 1-162-306-11 CERAMIC 0.01uF 20% 16V
D638 8-719-057-09 DIODE LNJ801LPDJA (r REC) C45 1-124-589-11 ELECT 47uF 20% 16V
C46 1-162-600-11 CERAMIC 4700PF 10% 16V
< RESISTOR > C47 1-162-294-31 CERAMIC 0.001uF 10% 50V
C48 1-126-160-11 ELECT 1uF 20% 50V
R715 1-247-815-91 CARBON 220 5% 1/4W
R716 1-249-411-11 CARBON 330 5% 1/4W C49 1-136-159-00 METALIZED PE FILM 0.033uF 5% 16V
R717 1-249-413-11 CARBON 470 5% 1/4W C50 1-136-159-00 METALIZED PE FILM 0.033uF 5% 16V
R718 1-249-415-11 CARBON 680 5% 1/4W C51 1-162-600-11 CERAMIC 4700PF 10% 16V
R719 1-249-417-11 CARBON 1K 5% 1/4W C52 1-162-600-11 CERAMIC 4700PF 10% 50V
C53 1-126-964-11 ELECT 10uF 20% 50V
R720 1-249-419-11 CARBON 1.5K 5% 1/4W
R721 1-249-421-11 CARBON 2.2K 5% 1/4W C54 1-126-157-11 ELECT 10uF 20% 16V
R722 1-247-843-11 CARBON 3.3K 5% 1/4W C55 1-126-964-11 ELECT 10uF 20% 50V
R723 1-247-807-31 CARBON 100 5% 1/4W C56 1-126-964-11 ELECT 10uF 20% 50V
R724 1-247-807-31 CARBON 100 5% 1/4W C57 1-164-159-21 CERAMIC 0.1uF 50V
C58 1-162-306-11 CERAMIC 0.01uF 20% 16V
R725 1-247-807-31 CARBON 100 5% 1/4W
R726 1-247-807-31 CARBON 100 5% 1/4W C59 1-164-159-21 CERAMIC 0.1uF 50V
R727 1-247-807-31 CARBON 100 5% 1/4W C61 1-164-159-21 CERAMIC 0.1uF 50V
R728 1-247-807-31 CARBON 100 5% 1/4W C62 1-126-967-11 ELECT 47uF 20% 16V
C63 1-164-159-21 CERAMIC 0.1uF 50V
< SWITCH > C64 1-126-959-11 ELECT 0.47uF 20% 50V

S651 1-554-303-21 SWITCH, TACTILE (·¯ ) C65 1-126-960-11 ELECT 1.0uF 20% 50V
S652 1-554-303-21 SWITCH, TACTILE (ª) C66 1-126-960-11 ELECT 1.0uF 20% 50V
S653 1-554-303-21 SWITCH, TACTILE ()) C67 1-126-964-11 ELECT 10uF 20% 50V
S654 1-554-303-21 SWITCH, TACTILE (0) C68 1-162-306-11 CERAMIC 0.01uF 20% 16V
S655 1-554-303-21 SWITCH, TACTILE (p) C69 1-162-306-11 CERAMIC 0.01uF 20% 16V

S656 1-554-303-21 SWITCH, TACTILE (P) C70 1-162-306-11 CERAMIC 0.01uF 20% 16V
S657 1-554-303-21 SWITCH, TACTILE (r REC) C71 1-162-306-11 CERAMIC 0.01uF 20% 16V
S658 1-554-303-21 SWITCH, TACTILE (H.SPEED DUBB) C73 1-162-306-11 CERAMIC 0.01uF 20% 16V
S659 1-554-303-21 SWITCH, TACTILE (CD SYNC) C74 1-126-964-11 ELECT 10uF 20% 50V
************************************************************
< FILTER >
* A-4303-512-A TCB BOARD,COMPLETE
******************* CF1 1-567-389-11 FILTER, CERAMIC
CF2 1-567-389-11 FILTER, CERAMIC
< CAPACITOR >
< CONNECTOR >
C1 1-162-294-31 CERAMIC 0.001uF 10% 50V
C2 1-126-967-11 ELECT 47uF 20% 16V * CN1 1-568-832-11 SOCKET, CONNECTOR 13P
C3 1-164-159-21 CERAMIC 0.1uF 50V
C5 1-162-306-11 CERAMIC 0.01uF 20% 16V < DIODE >
C6 1-162-306-11 CERAMIC 0.01uF 16V
D1 8-719-933-33 DIODE UZL-6L1-TA
C7 1-101-004-00 CERAMIC 0.01uF 50V D2 8-719-987-63 DIODE 1N4148M-TA
C8 1-162-306-11 CERAMIC 0.01uF 20% 16V
C9 1-162-306-11 CERAMIC 0.01uF 20% 16V < FRONTEND >
C11 1-164-159-21 CERAMIC 0.1uF 50V
C12 1-162-198-31 CERAMIC 8.2PF 10% 50V FE1 1-233-533-11 ENCAPSULATED COMPONENT
FE2 1-239-260-11 ENCAPSULATED COMPONENT
C14 1-162-306-11 CERAMIC 0.01uF 20% 16V
C21 1-102-514-11 CERAMIC 22PF 5% 50V

– 114 –
 TCB TRANS
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< IC > R43 1-247-843-11 CARBON (SMALL)3.3K 5% 1/4W

IC1 8-759-288-54 IC LC72130 R44 1-247-843-11 CARBON (SMALL)3.3K 5% 1/4W

IC2 8-759-176-03 IC LA1835 R46 1-249-442-11 CARBON 510 5% 1/4W
R47 1-249-399-11 CARBON 33 5% 1/4W
< IFT > R48 1-247-843-11 CARBON (SMALL)3.3K 5% 1/4W
R49 1-249-393-11 CARBON 10 5% 1/4W
IFT41 1-409-636-11 TRANSFORMER, IF (CERAMIC FILTER)
R50 1-249-429-11 CARBON 10K 5% 1/4W
< COIL > R51 1-249-441-11 CARBON 100K 5% 1/4W
R52 1-249-429-11 CARBON 10K 5% 1/4W
L41 1-410-119-11 MICRO INDUCTOR (EL TYPE) 1mH R53 1-249-425-11 CARBON 4.7K 5% 1/4W
R54 1-249-425-11 CARBON 4.7K 5% 1/4W
< FILTER >
R99 1-249-399-11 CARBON 33 5% 1/4W
LPF41 1-239-845-11 FILTER, LOW PASS
LPF42 1-239-845-11 FILTER, LOW PASS < VARIABLE RESISTOR >

< TRANSISTOR > RV41 1-238-600-11 ADJ, CARBON 10K

RV42 1-238-601-11 ADJ, CARBON 22K
Q1 8-729-230-99 TRANSISTOR 2SC2669OY-TPE4
Q2 8-729-230-99 TRANSISTOR 2SC2669OY-TPE4 < TERMINAL >
Q3 8-729-230-99 TRANSISTOR 2SC2669OY-TPE4
Q4 8-729-230-99 TRANSISTOR 2SC2669OY-TPE4 TM1 1-537-238-21 TERMINAL BOARD (ANTENNA)
Q5 8-729-422-57 TRANSISTOR BN1A4M-TP
< VIBRATOR >
< RESISTOR >
X21 1-760-549-11 VIBRATOR, CRYSTAL (4.5MHz)
R1 1-249-401-11 CARBON 47 5% 1/4W X41 1-577-075-11 OSCILLATOR, CERAMIC (456KHz)
R2 1-249-411-11 CARBON 330 5% 1/4W X42 1-760-220-11 FILTER, CERAMIC
R3 1-249-411-11 CARBON 330 5% 1/4W X43 1-527-981-00 FILTER, CERAMIC
R5 1-249-411-11 CARBON 330 5% 1/4W ************************************************************
R6 1-247-863-91 CARBON (SMALL)22K 5% 1/4W
* 1-664-014-11 TRANS BOARD
R7 1-249-411-11 CARBON 330 5% 1/4W ***********
R8 1-249-411-11 CARBON 330 5% 1/4W
R9 1-247-863-91 CARBON (SMALL)22K 5% 1/4W 1-533-399-31 HOLDER, FUSE
R10 1-249-411-11 CARBON 330 5% 1/4W
R11 1-247-863-91 CARBON (SMALL)22K 5% 1/4W < CONNECTOR >

R12 1-249-411-11 CARBON 330 5% 1/4W * CN901 1-564-522-11 PLUG, CONNECTOR 7P

R13 1-249-411-11 CARBON 330 5% 1/4W * CN902 1-564-518-11 PLUG, CONNECTOR 3P
R14 1-247-863-91 CARBON (SMALL)22K 5% 1/4W CN903 1-774-108-11 PIN, CONNECTOR (PC BOARD)
R15 1-249-429-11 CARBON 10K 5% 1/4W
R16 1-249-437-11 CARBON 47K 5% 1/4W < CONNECTOR >

R19 1-249-399-11 CARBON 33 5% 1/4W ! CNP901 1-558-943-41 CORD, POWER (E, IA)
R21 1-247-807-31 CARBON (SMALL)100 5% 1/4W ! CNP901 1-575-651-21 CORD, POWER (EA, SP, MY)
R22 1-249-425-11 CARBON 4.7K 5% 1/4W
R23 1-249-425-11 CARBON 4.7K 5% 1/4W < FUSE >
R24 1-249-425-11 CARBON 4.7K 5% 1/4W
! F901 1-532-388-31 FUSE, TIME-LAG (2A, 250V)
R25 1-247-807-31 CARBON (SMALL)100 5% 1/4W ! F902 1-532-504-31 FUSE, TIME-LAG (4A, 250V) (E, EA, SP, IA)
R26 1-249-411-11 CARBON 330 5% 1/4W
R27 1-249-425-11 CARBON 4.7K 5% 1/4W < RESISTOR >
R28 1-247-843-11 CARBON (SMALL)3.3K 5% 1/4W
R29 1-249-417-11 CARBON 1K 5% 1/4W ! R901 1-219-119-81 FUSIBLE 0.1 5% 1/4W F
(MY)
R30 1-249-417-11 CARBON 1K 5% 1/4W ! R901 1-219-124-11 FUSIBLE 0.68 5% 1/4W F
R31 1-249-417-11 CARBON 1K 5% 1/4W (EXCEPT MY)
R32 1-249-417-11 CARBON 1K 5% 1/4W ! R902 1-219-119-81 FUSIBLE 0.1 5% 1/4W F
R33 1-247-807-31 CARBON (SMALL)100 5% 1/4W (MY)
R34 1-249-429-11 CARBON 10K 5% 1/4W ! R902 1-219-124-11 FUSIBLE 0.68 5% 1/4W F
(EXCEPT MY)
R35 1-249-429-11 CARBON 10K 5% 1/4W ! R903 1-219-119-81 FUSIBLE 0.1 5% 1/4W F
R36 1-249-437-11 CARBON 47K 5% 1/4W (EXCEPT MY)
R37 1-249-417-11 CARBON 1K 5% 1/4W
R41 1-249-429-11 CARBON 10K 5% 1/4W

The components identified by mark

! or dotted line with mark ! are
critical for safety.
Replace only with part number
specified.
– 115 –
HCD-XB6K

TRANS
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
! R903 1-219-120-11 FUSIBLE 0.15 5% 1/4W F
(MY) ***************
! R904 1-219-119-81 FUSIBLE 0.1 5% 1/4W F HARDWARE LIST
(EXCEPT MY) ***************
! R904 1-219-120-11 FUSIBLE 0.15 5% 1/4W F
(MY) #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
#2 7-685-871-01 SCREW +BVTT 3X6 (S)
< SWITCH > #3 7-685-872-09 SCREW +BVTT 3X8 (S)
#4 7-685-650-79 SCREW +BVTP 3X16 TYPE2 N-S
! S901 1-762-753-11 SWITCH, VOLTAGE SELECTION #5 7-685-862-09 SCREW +BVTT 2.6X6 (S)
(VOLTAGE SELECTOR) (EXCEPT MY)
#6 7-685-131-19 SCREW +BTP 2.6X4 TYPE2 N-S
< TRANSFORMER > #7 7-685-533-19 SCREW +BTP 2.6X6 TYPE2 N-S
#8 7-621-775-10 SCREW +B 2.6X4
! T901 1-431-052-11 TRANSFORMER, POWER #9 7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S
************************************************************ #10 7-623-921-01 RING,RETAINGNG, CAPSTAN

************** #11 7-621-775-00 SCREW +B 2.6X3

MISCELLANEOUS #12 7-621-255-15 SCREW +P 2X3
************** ************************************************************

11 1-769-974-11 WIRE (FLAT TYPE) (13 CORE) *******************************

11 1-773-006-11 WIRE (FLAT TYPE) (15 CORE) ACCESSORIES & PACKING MATERIALS
58 1-773-161-11 WIRE (FLAT TYPE) (21 CORE) *******************************
59 1-769-949-11 WIRE (FLAT TYPE) (11 CORE)
120 1-773-051-11 WIRE (FLAT TYPE) (17 CORE) 1-475-115-11 REMOTE COMMANDER (RM-SD70)
1-501-374-11 ANTENNA, LOOP
156 1-777-868-11 WIRE (FLAT TYPE) (19 CORE) 1-501-659-41 ANTENNA (FM)
! 159 1-569-007-11 ADAPTOR, CONVERSION 2P (E,IA) 3-859-536-11 MANUAL, INSTRUCTION (ENGLISH)
! 160 1-569-008-11 ADAPTOR, CONVERSION 2P (EA, SP) 3-859-536-31 MANUAL, INSTRUCTION (FRENCH, SPANISH)
357 1-452-538-11 MAGNET (E, EA, SP)
! 401 8-820-020-01 OPTICAL PICK-UP KSS-213D/Q-NP
3-859-536-41 MANUAL, INSTRUCTION (CHINESE)
402 1-769-069-11 WIRE (FLAT TYPE) (16 CORE) 3-859-536-51 MANUAL, INSTRUCTION (ARABIC) (EA)
! CNP901 1-558-943-41 CORD, POWER (E, IA) 4-991-151-01 COVER, BATTERY (for RM-SD70)
! CNP901 1-575-651-21 CORD, POWER (EA, MY, SP)
HP101 1-500-093-11 HEAD, MAGNETIC (PLAYBACK)
HRPE1011-500-094-11 HEAD, MAGNETIC (REC/PB/ERASE)

M1 X-3371-223-1 MOTOR ASSY, CAPSTAN

M2 A-2004-410-A MOTOR ASSY, DC (TRIGGER)
M201 A-4660-977-A MOTOR ASSY (TABLE)
M101 X-4917-504-1 MOTOR ASSY (SPINDLE)
M102 X-4917-523-4 MOTOR ASSY (SLED) The components identified by mark
! or dotted line with mark ! are
critical for safety.
! T901 1-431-052-11 TRANSFORMER, POWER Replace only with part number
************************************************************ specified.

Sony Corporation 97E057023-1

Printed in Singapore © 1997. 5
9-960-925-11 Home A&V Products Company
Published by General Engineering Dept.
(Shibaura)
– 116 –