DIRECTIONS: Choose the letter of the best answer.

1. What was one significant development in the history of Industrial Arts?

A. Introduction of digital technology
B. Development of basic hand tools
C. Emergence of industrial machinery
D. Establishment of trade schools

2. Which of the following areas is NOT part of Industrial Arts?

A. Carpentry
B. Culinary arts
C. Automotive repair
D. Electrical wiring

3. How does Industrial Arts support career education?

A. By focusing on theoretical knowledge
B. By offering practical skills applicable in various trades
C. By specializing solely in digital technologies
D. By limiting career opportunities to academia

4. Which of the following is a potential career opportunity in Industrial Arts?

A. Mechanical engineering
B. Software development
C. Agricultural management
D. Plumbing and pipe fitting

5. What is the main purpose of building codes in the Philippines?

A. To ensure safety and structural integrity
B. To promote aesthetic design
C. To reduce construction costs
D. To limit architectural creativity

6. Which government agency regulates building codes in the Philippines?

A. Department of Trade and Industry (DTI)
B. National Building Code of the Philippines (NBCP)
C. Department of Public Works and Highways (DPWH)
D. Bureau of Fire Protection (BFP)

7. The Electrical Code in the Philippines is intended to:

A. Increase the cost of electrical goods
B. Standardize electrical installations and ensure safety
C. Focus on aesthetic design of electrical systems
D. Promote outdated electrical practices

8. Why is adherence to traffic and road signs important?

A. To ensure smooth traffic flow and safety
B. To increase revenue from traffic fines
C. To reduce vehicle emissions
D. To minimize construction costs

9. Which agency oversees the implementation of traffic codes in the Philippines?

A. Department of Transportation (DOTr)
B. Department of Public Works and Highways (DPWH)
C. National Bureau of Investigation (NBI)
D. Philippine National Police (PNP)

10. What is the primary function of traffic and road signs?

A. To provide instructions and warnings for safe driving
B. To display advertisements
C. To increase vehicle speed
D. To beautify roadways

11. What is essential for maintaining hand tools?

A. Regular lubrication and cleaning
B. Leaving them exposed to elements
C. Using them with damaged parts
D. Ignoring manufacturer instructions

12. Which tool is classified as a power tool?

A. Hammer
B. Drill
C. Screwdriver
D. Pliers

13. What should be done if a power tool shows signs of malfunction?

A. Continue using it until it breaks
B. Stop using it and report it for repair
C. Use it with caution without reporting
D. Attempt to fix it without proper tools

14. What is a key maintenance task for power tools?

A. Regular inspection for damage
B. Using them without maintenance
C. Storing them in a damp environment
D. Ignoring calibration procedures

15. How often should hand tools be inspected for safety?

A. Only when they appear damaged
B. Regularly, as part of a maintenance schedule
C. Once a year
D. Whenever they are used

16. Which tool is used for tightening bolts and nuts?

A. Pliers
B. Wrench
C. Screwdriver
D. Hammer

17. How would you classify a circular saw?

A. Hand tool
B. Power tool
C. Measuring instrument
D. Safety equipment

18. What category does a hammer fall into?

A. Power tool
B. Hand tool
C. Instrument
D. Equipment

19. Which of the following tools is used for precision cutting and measuring?
A. Circular saw
B. Measuring tape
C. Hammer
D. Wrench

20. A digital multimeter is primarily used to:

A. Measure electrical parameters such as voltage, current, and resistance
B. Measure the speed of rotation
C. Measure temperature changes
D. Measure length and width

21. How should safety precautions be applied when performing measurements?

A. Ignoring safety guidelines
B. Using appropriate personal protective equipment and tools
C. Using tools with visible damage
D. Working in an unventilated area

22. What is the correct way to convert English measurements to Metric units?
A. Using outdated conversion tables
B. Estimating measurements
C. Using accurate conversion factors
D. Ignoring standard units

23. Which of the following is a correct method for converting measurements?

A. Rounding to the nearest whole number
B. Using a conversion chart
C. Estimating values
D. Ignoring conversion rules

24. What does Ohm’s Law state about the relationship between voltage, current, and
resistance?
A. Voltage = Current ÷ Resistance
B. Voltage = Current + Resistance
C. Voltage = Current × Resistance
D. Voltage = Resistance ÷ Current

25. How is a fraction converted to a decimal?

A. By multiplying the numerator by 100
B. By dividing the numerator by the denominator
C. By adding the numerator to the denominator
D. By subtracting the numerator from the denominator

26. What is an essential practice when converting between different measurement

systems?
A. Using rough estimates
B. Ignoring standard units
C. Ensuring accuracy with correct conversion factors
D. Using outdated tables

27. When solving circuit problems using Ohm’s Law, which formula correctly
represents the calculation for voltage?
A. Voltage = Current ÷ Resistance
B. Voltage = Resistance × Current
C. Voltage = Current + Resistance
D. Voltage = Resistance ÷ Current

28. What is a key consideration when performing mensuration?

A. Ensuring measurements are precise and accurate
B. Rushing through calculations
C. Using approximations
D. Ignoring measurement standards

29. What safety measure should be followed when handling electrical tools?
A. Ignoring safety certifications
B. Using tools with exposed wires
C. Ensuring tools are properly insulated and grounded
D. Operating tools with wet hands

30. Why is it crucial to follow the building codes in construction?

A. To increase the cost of construction
B. To ensure safety and compliance with legal standards
C. To limit the use of new materials
D. To simplify the design process

31. What is a critical aspect of using an ampere meter correctly?

A. Measuring voltage levels
B. Measuring electrical current accurately
C. Measuring temperature
D. Measuring rotational speed

32. Which instrument is used to measure the speed of rotation?

A. Multimeter
B. Tachometer
C. Oscilloscope
D. Ampere meter
33. How is an oscilloscope used in practice?
A. To diagnose signal waveform issues
B. To measure electrical current
C. To test insulation resistance
D. To measure the speed of a rotating object

34. What part of an oscilloscope shows the waveform of electrical signals?

A. Input terminal
B. Power switch
C. Display screen
D. Voltage control knob

35. What should be checked to interpret readings accurately on a measuring

instrument?
A. Adjust the instrument settings as needed
B. Ignore the calibration process
C. Use the instrument in dim light
D. Use the instrument without reading the manual

36. How often should hand tools be inspected for safety?

A. Once a year
B. Whenever they are used
C. Only when they appear damaged
D. Regularly, as part of a maintenance schedule

37. What role does mensuration play in Industrial Arts?

A. Tests material durability
B. Provides design inspiration
C. Ensures precise measurement and calculation for projects
D. Repairs equipment

38. What is a key task in maintaining power tools?

A. Using them without maintenance
B. Storing them in a damp environment
C. Regular inspection for damage
D. Ignoring calibration procedures

39. Which tool is classified as a power tool?

A. Screwdriver
B. Drill
C. Hammer
D. Pliers

40. What should be done if a power tool shows signs of malfunction?

A. Continue using it until it breaks
B. Stop using it and report it for repair
C. Use it with caution without reporting
D. Attempt to fix it without proper tools
41. What is the primary function of a tachometer?
A. To measure the speed of rotation
B. To measure electrical resistance
C. To measure voltage
D. To measure temperature

42. What part of the oscilloscope is used to adjust the time base?
A. Time/div knob
B. Volts/div knob
C. Intensity control
D. Trigger control

43. What is the function of an oscilloscope in electrical measurements?

A. To measure electrical current
B. To visualize waveforms of electrical signals
C. To measure resistance
D. To measure temperature

1. 44. How should tools and equipment be maintained for optimal performance?
A. Regular cleaning and timely repairs
B. Using them without maintenance
C. Storing them in damp conditions
D. Ignoring manufacturer instructions

45. What is a critical practice when converting decimal numbers to fractions?

A. Dividing the decimal by 1 and simplifying
B. Using a conversion table
C. Multiplying the decimal by 100
D. Adding the decimal to 1

46. What is a major advantage of using an oscilloscope?

A. Measuring voltage accurately
B. Visualizing and analyzing signal waveforms
C. Measuring rotational speed
D. Measuring current

47. Which government agency regulates the implementation of building codes in the
Philippines?
A. National Building Code of the Philippines (NBCP)
B. Department of Trade and Industry (DTI)
C. Department of Public Works and Highways (DPWH)
D. Bureau of Fire Protection (BFP)

48. When solving circuit problems using Ohm’s Law, what should be the first step?
A. Determine the current and resistance
B. Measure voltage with a multimeter
C. Identify the power rating of the circuit
D. Check the insulation of the wiring

49. How often should measuring instruments be calibrated?

A. Only when they show signs of malfunction
B. Periodically, as part of a maintenance schedule
C. Once a year
D. Only when purchased

50. What is the primary role of a multimeter?

A. To measure temperature
B. To measure electrical parameters such as voltage, current, and resistance
C. To visualize signal waveforms
D. To measure rotational speed