Certification Warranty Keysight £44161 Keysight Technologies certifies that this product met its published specifications at the time of shipment fram the factory. Keysight Technologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology, to the extent allowed by the Institute's calibration facility, and to the calibration facilities of other International Standards Organization members. This Keysight Technologies instrument product is warranted against defects in material and workmanship for a period of one year from date of shipment. During the warranty period, Keysight Technologies will at its option, either repair or replace products which prove to be defective. For warranty service or repair, this product must be returned to a service facility designated by Keysight Technologies. Buyer shall prepay shipping charges to Keysight Technologies and Keysight Technologies shall pay shipping charges, duties, and taxes for products returned to Keysight Technologies from another country. Keysight Technologies warrants that its software and firmware designated by Keysight Technologies for use with an instrument will execute its programming instructions when properly installed on that instrument. Keysight Technologies does not warrant that the operation of the inetrument, or firmware will bo uninterrupted or error froo E4417 Power Meters Service GuideLimitation of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by Buyer, Buyer-supplied software or interfacing, unauthorized modification or misuse, operation outside of the environmental specifications for the product, or improper site preparation or maintenance. NO OTHER WARRANTY IS EXPRESSED OR IMPLIED. KEYSIGHT TECHNOLOGIES SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Exclusive Remedies THE REMEDIES PROVIDED HEREIN ARE BUYER'S SOLE AND EXCLUSIVE REMEDIES. KEYSIGHT TECHNOLOGIES SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON CONTRACT, TORT, OR ANY OTHER LEGAL THEORY. Warnings and Cautions This gui 2 uses warnings and cautions to denote hazards. ‘Awarning calls attention to a procedure, practice or the like, which, if not correctly performed or adhered to, could result in injury or the loss of life. Do not proceed beyond a warning until the indicated conditions are fully understood and met. A caution calls attention to a procedure, practice or the like which, if not correctly performed or adhered to, could result in damage to or the destruction of part or all of the equipment. Do not proceed beyond a caution until the indicated conditions are fully understood and met. Keysight £4416A/E4417A Power Meters Service GuideSafety Symbols The following symbol on the instrument and in the documentation indicates precautions that must be taken to maintain safe operation of the instrument. Caution risk of danger. The Instruction Documentation Symbol. The product is marked wit this symbol ‘when it is necessary forthe user to refer tothe instructions in the supplied documentation. ‘This symbol indicates the operating switch for ‘Stand-by’ mode. Note the instrument is NOT isolated from the mains when the switch is pressed. To isolate the instrument, the mains coupler (mains input cord) should be removed ‘rom the power supa. Ne Altemating current AC). This symbol indicates the operating switch for ‘Or’ mode). External Protective Earth Terminal While this is@ Class product, provided with a protective earthing conductor in a power cord, an extemal protective earthing terminal has also been [rewided hie trminal ie fr ise where tha earthing eanant he accired At lact an ‘TEAWG earthing conductor should be used in such an instance, to ground the instrument to an assured earth terminal. Keysight E4416A/E4417A Power Meters Service Guide 5Personal Safety Considerations This is a Safety Class | product (provided with a protective earthing ground incorporated in the power cord). The mains plug shall only be inserted in a socket outlet provided with a protective earth contact. Any interruption of the protective conductor, inside or outside the instrument, is likely to make the instrument dangerous. Intentional interruption is prohibited If this instrument is not used as specified, the protection provided by the cquipment could be impaired. This instrument must be used in a normal condition (in which all means of protection are intact) only. No operator serviceable parts inside. Refer servicing to qualified personnel. To prevent electrical shock, do not remove covers. For continued protection against fire hazard, replace the line fuse(s) only with fuses of the same type and rating (for example, normal blow, time delay, etc.). The use of other fuses or material is prohibited. General Safety Considerations CIID Before this instrument is switched on, make sure it has been properly grounded through the protective conductor of the ac power cable toa socket outlet provided with protective earth contact. Any interruption of the protective (grounding) conductor, inside or outside the instrument, or disconnection of the protective earth terminal can result in personal injury. Any adjustments or service procedures that require operation of the instrument with protective covers removed should be performed only by trained service personnel. Keysight £4416A/E4417A Power Meters Service GuideRegulatory Markings Tho CE mark shows that the product complise with all the relevant Europoan legal Directives (if accompanied by a year, it signifies when the design was proven. ICESINMB-001 This ISM device complies with Canadian ICES-001 Cet appareil ISM est conforme & la norme NMB-UI du Canada ROUP 1 ISM oe Thisis the symbol ofan industrial Scintfic and Medical Group 1 Cass & product. CLASS A Keysight E4416A/E4417A Power Meters Service Guide 7IEC 1010-1 Compliance This instrument has been designed and tested in accordance with IEC Publication 1010-1 +A1:1992 Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use and has been supplied in a safe condition. The instruction documentation contains information and warnings which must be followed by the user to ensure safe operation and to maintain the instrument in a safe condition. Recommended Calibration Interval Keysight Technologies recommends a two-year calibration cycle for the E4416A and E4417A power meter. 8 Keysight £4416A/E4417A Power Meters Service GuideSales and Service Offices By Internet, phone, or fax, get assistance with all your test and measurement needs. In any correspondence or telephone conversations, refer to the power sensor by HE ie rccer number ana fat sora number With tis information, the Keysight Technologies representative can quickly determine whether your unit is still within its warranty period. Coy United States Canada China Europe Japan Korea Latin america Taiwan Other Asia Pacific Countries: Eoctns 1800829 4444 877 894 4414 800810 0189 3120547 2111 (61) 426 56 7832 (080) 763 0800 (30s) 26y /200 (0800 047 866 (65) 6375 8100 Peng 800 829 4433) 800 746 4866 800 820 2816 (61) 426 56 7840 (080) 763 0900 (0800 286 331 (65) 6755 0042 Keysight E4416A/E4417A Power Meters Service GuideReturning Your Power Meter for Service Use the information in this section if you need to return your power meter to Keysight Technologies. Package the Power Meter for Shipment Use the following steps to package the power meter for shipment to Keysight Technologies for service: |. Fill in a blue service tag (available at the end of this guide) and attach it to the power meter. Please be as specific as possible about the nature of the problem, Send a copy of any or all of the following information: — Any error messages that appeared on the power meter display. — Any information on the performance of the power meter. Power meter damage can result from using packaging materials other than those specified. Never use styrene pellets in any shape as packaging materials. They do not adequately cushion the power meter or prevent it from shifting in the carton. Styrene pellets cause power meter damage by generating static electricity and by lodging in the rear panel. 2, Use the original packaging materials or a strong shipping container that is made of double-walled, corrugated cardboard with 159 kg (350 lb) bursting strength. The carton must be both large enough and strong enough to accommodate the power meter and allow at least 3 to 4 inches on all sides of the power meter for packing materia. 10 Keysight £4416A/E4417A Power Meters Service Guide