Catalogue

1 Technical data and operating conditions…………………………………01

2 Description of accessories…………………………………………………02

3 Mechanical installation…………………………………………………03-10

3.1 Installation example………………………………………………………03

3.2 Base plate installation… … … … … … … … … … … … … … … … … …04-05

3.3 Pull arm installation………………………………………………………06

3.4 Push arm installation…………………………………………………07-08

3.5 Drive system installation…………………………………………………09

3.6 Hood installation… … … … … … … … … … … … … … … … … … … … … …09

3.7 Connection of drive system and pull arm ………………………………10

4 Safety precautions for vector controller……………………………………11

5 Digital display and operation instructions… … … … … … … … … … … …11

6 Function selection and terminal block……………………………………12

7 Wiring diagram… … … … … … … … … … … … … … … … … … … … … …12-13

 1 Wiring diagram
Supply voltage
Power frequency
Rated power
Fuse protection A slow action
temperature range
Wiring diagram

Humidity range Relative humidity is not more than 85%

1.1 Product features

The use of brushless motor planetary gear reduction technology and ultra-quiet operation
make your use more perfect and convenient; Multi-functional interface and full-function
remote control technology have adjustable functions such as double-door interlock and
position feedback with excellent reliability and durability.

1.2 Performance parameters

Applicable Swinging doors of various
swinging door Door width 600~1200 mm
materials
Automatic door
opening angle 90 degree Door weight less than 120 kg
Door opening
holding time 0.5~10 second
Opening speed Adjustable
closing speed

This swinging door operator also has the following six functions:
1. Remote closing and door opening and closing prohibited
2. Buffer function
3. Automatic overload protection
4. The locking force adjustment function is continuously adjustable
5. Intelligent obstacle protection
6. Intelligent overheat protection
The overall dimension of the host is 565mm long, 80mm wide, and 104mm thick. The
input power is static (maximum) 65~90W, and the power supply is AC220, AC18V.
Work program door opening signal -- control unlocking -- door opening -- brake stopping
-- door opening and holding -- automatic door closing -- buffer -- door locking

1.3 Application
The application market of automatic door operator is very broad, which can be widely
used in swinging doors of various systems such as access control, building intercom,
and induction door. It also has functions such as pushing to open, pushing into energy-
saving effect, and is very suitable for places with disabled people! It can also be widely
used in automatic doors of purification rooms and shower rooms, high-tech R&D centers,
bank headquarters self-service bank entrances and exits, supermarket entrances and
exits, high-end hospitals, restaurants, private clubs, clubs, museums, and public
restrooms doors of high-end office buildings and department stores, factory workshop
doors, isolation doors of hospital corridors, doors of clinical treatment rooms, operating
rooms, and examination rooms, public offices, secret institutions, business hotels,
airports, Public places, senior apartments, leaders' offices.

01
2 Description of accessories

Power cord hole Sensor iso-wire hole

Base plate

Hood

Power wiring base Motor Controller

Drive Output shaft

Pull arm (or push arm)

Remote control

Push arm (or pull arm)

02
3 Mechanical installation

3.1 Installation example

Pull arm installation: suitable for opening the door wing inwards
(the drive system is inside)

Push arm installation: suitable for opening door wing outward

(drive system is inside)

03
 3 Mechanical installation

3. 2 Base plate installation

Pull-arm installation
∅ ∅ 20 sensor wire entry
20
po
we
r li
ne
en
try

The base plate is fastened to the door

frame with eight countersunk wood
screws according to the dimensions
shown in the figure (for steel structure,
it is fastened with countersunk screws)

Right installation of automatic door

∅
20 ∅ 20 sensor wire entry
po
we
r li
ne
en
try

The base plate is fastened to the door frame

with eight countersunk wood screws according
to the dimensions shown in the figure (for steel
structure, it is fastened with countersunk screws)

Left installation of automatic door

04
 3 Mechanical installation

3. 2 Base plate installation

Push arm installation

∅ ∅ 20 sensor wire entry

20
po
we
r li
ne
en
try

Note: The base plate and door frame are aligned

The base plate is fastened to the door

frame with eight countersunk wood
screws according to the dimensions
shown in the figure (for steel structure,
it is fastened with countersunk screws)

Right installation of automatic door

∅
20 ∅ 20 sensor wire entry
po
we
r li
ne
en
try

Note: The base plate and door frame are aligned

The base plate is fastened to the door frame

with eight countersunk wood screws according
to the dimensions shown in the figure (for steel
structure, it is fastened with countersunk screws)

Left installation of automatic door

05
3 Mechanical installation

3.3 Pull arm installation

10mm from door frame

100

The pull arm fixed seat is

fastened on the door wing
as shown in the figure

Move the stop block to adjust

the door opening angle
(when installed on the left,
the stop block is on the left)

Right installation of automatic door

06
3 Mechanical installation

3.4 Push arm installation

The fixed seat of push arm is fastened to the

door wing with two round wood screws
according to the dimensions shown in the
figure (for steel doors, cross pan head
screws are used for fastening)

According to the depth L of the door frame,

loosen the three clamping bolts to adjust
the length of the push arm so that the
included angle between the push arm and
the door body is 90 ° as shown in the figure.

Right installation of automatic door

07
3 Mechanical installation

3.4 Push arm installation

Stop block

Adjust the stop block in the U-shaped

hole to the position shown in the figure

08
3 Mechanical installation

3.5 Drive system installation

Hook the drive system on the installed base plate as shown in

the figure and fasten it with eight hexagon socket head bolts.

3.6 Hood installation

The way to open the hood

09
3 Mechanical installation

3.7 Connection of drive system and pull arm

Drive shaft extension

device

10
Power supply, touch switch selection, digital display and

4 Safety precautions for vector controller

·Please entrust electrical engineering professionals to carry out wiring operation,
otherwise electric shock and fire may be caused!
·For safety, please cut off the power supply or restart the equipment after the door is
closed in place!
·Non-professional personnel are not allowed to maintain, check and replace parts!

·It is forbidden to disassemble and transform this product!

·Do not use the door leaf that exceeds the specified weight, otherwise it will cause
failure!
function description

·Please select 12V for electric lock!

5 Digital display and operation instructions

0 represents door opening speed 5 represents the value of door opening speed is 5

Fault code 0: Door opening speed (0-9 adjustable)

05
1. Electric lock
Remote control

E1: Overvoltage 1: Closing speed (0-9 adjustable)

E2:Undervoltage 2. GND
E3:Motor fault 2: Buffer speed (0-9 adjustable)
E5:Memory failure 3: Buffer distance (0-9 adjustable) 3. GND

4: Door opening holding time (0-9 seconds adjustable) 4. Access control

Status code 5. Safety beam
【】 ：
In operation 5: Anti-trap sensitivity (0-9 adjustable)
CH: Close the door in place 6: Half opening amplitude (not adjustable) Menu +/- Confirmation/test 6. Radar
OH: Open the door in place 7. Interlock
H1: Normally open after power failure 7: Motor direction (O: right; 1: left)
A 485 8. GND
H2:Half open
B communication 8: Primary/secondary (1: primary: 2: secondary)
H3:Normally open
9.12V
H4:Lock 9: Battery mode (O: power off normally open; 1: automatic)
H5:Interlock 10.12V
H6:Safety light
A: Remote control input (0: external remote control; 2; five-gear switch)
正 H7:Access control C: Main control and auxiliary control (0: main control; 1: auxiliary control)
负 Battery H8:Radar L
E: Sequential switch amplitude Power Supply
H9:Stop N

Menu switch function options from 0-E

+/-Set the adjustable parameters of the function
Confirm/Test represents saving the modified data

Mode 1: single door opening setting (factory default): C0

Mode 2: double doors are set to open/close simultaneously (connect two 485 communication
lines of two controllers):
Main controller: C0, E0
Auxiliary controller: C1, E0
All external signals are connected to the main controller
Mode 3: double doors are set to open/close simultaneously (connect two 485 communication
lines of two controllers):
Main controller: C0, E0 (E0 represents simultaneous opening of double doors)
Auxiliary controller: C1, E2 (E2 represents the difference between the closing sequence of
two doors by about 5 times 2=10 degrees)
All external signals are connected to the main controller
Note: 1. In the double-door mode, if 485 communication is not connected, the main control
door will move and the auxiliary control door will not move (display H9).
2. Without receiving the safety light, if the door encounters a physical obstacle during
the opening process, the door will stop and automatically give an opening signal every
5 seconds. If the door still cannot pass the obstacle after five opening signals, it will stop
at the obstacle position and wait for the external signal command.
3. Without receiving the safety light, if the door encounters physical obstacles during
closing, the door will open the door. If the door still cannot pass the obstacles after five
times of closing, it will stop at the obstacle position f and wait for the external signal
command.

11
6 Function selection and terminal block
11. Function selection and terminal description
1. Place the door leaf in the middle, connect the 220V power line to the controller, turn
on the power switch, and the door will execute the slow closing action.
2. If the door is opened after power-on, you need to adjust the motor direction: press

Function selection and terminal block

the menu continuously → turn to 7 (representing the motor direction) 1 (representing
the left turn of the motor) → press+/- to change to 7 (representing the motor direction)
0 (representing the right turn of the motor) → press Confirmation → power off and
power on again.
3. After the door is slowly closed in place, carry out the self-learning of door opening
by pressing the test. The door will slowly execute the door opening action to the open
position, and the above completes the self-inspection.
Parameter statement:

-Attachment: The opening of the collection mode needs to be explained in

advance with the manufacturer
-For fault codes and signal codes received by the controller, please refer to
the instructions on the label paper

7 Wiring diagram

1. Radar wiring diagram

Power Power
Signal Signal supply supply

Radar 1: Electric lock

2: GND

10 9 8 7 6 5 4 3 2 1 3: GND
4: Access control
5: Safety beam
6: Radar
7: Interlock
Motor
8: GND
220V
Power supply 9: 12V
10: 12V

Right side of the controoler

12
Installation and function description of remote control

2. Access control wiring diagram

COM NO 12V GND

Access control 1: Electric lock

2: GND
3: GND
10 9 8 7 6 5 4 3 2 1
4: Access control
5: Safety beam
6: Radar
7: Interlock
Motor
8: GND
220V
Power supply 9: 12V
10: 12V

Right side of the controoler

3.Safety light wiring diagram

COM NO 12V GND

Safety light 1: Electric lock

2: GND
3: GND
10 9 8 7 6 5 4 3 2 1
4: Access control
5: Safety beam
6: Radar
7: Interlock
Motor
8: GND
220V
Power supply 9: 12V
10: 12V

Right side of the controoler

4.Electric lock(12V) wiring diagram
Red Black
line line

Electric lock 1: Electric lock

2: GND
3: GND
10 9 8 7 6 5 4 3 2 1
4: Access control
5: Safety beam
6: Radar
7: Interlock
Motor
8: GND
220V
Power supply 9: 12V
10: 12V

Right side of the controoler

5.Backup battery (lithium battery) wiring diagram

Remote
control
485
communication line

Battery +-

Backup battery +-

Left side of the controller

6.Double-door interconnection wiring diagram

Remote Remote
control control
485 485
communication line communication line

Battery +- Battery +-

Left side of the controller Left side of the auxilliary controller

13
This manual is for user reference only. The company has the right to modify the contents of
this manual at any time. Without the written permission of the company, it is not allowed to
control any part of the contents of this manual in mechanical, electronic or any other form.
Patented products, counterfeiting must be investigated!