DATA SHEET FOR GLOBE VALVES
1. Valve Manufacturer :
2. Size : 2" and above Rating : ANSI 300# Design Standard : BS:5352
3. Purchaser's Specification : Refer Technical notes for Gate & Globe Valves
4. Design Pressure : 49 kg/cm2(g) Design Temperature : -29oC to + 65°C
5. Corrosion Allowance : 1.5mm Service : Natural Gas
6. End Connections : Flanged both ends as per ASME B 16.5
Butt Weld both ends as A-16.25
Flanged one end butt weld other end
Socket weld both ends as per ASME B16.11
7. Flanges (where applicable) : a) RF FF RTJ
b) Serrated Smooth (125 to 200 AARH)
8. Connecting Pipe Specification :
9. Valve Material Specification :
Part Material Material Offered (Equivalent or Superior)
9.1 Body ASTM A 216 Gr.WCB
9.2 Bonnet (Bolted) ASTM A 216 Gr.WCB
9.3 Stem (Rising) 13% Cr. Steel (No Casting)
9.4 Disc(Loose Plug/Ball Type) (ASTM A 216 Gr. WCB + 13% Cr Steel Facing) /
13% Cr Steel (Stellited)
9.5 Body Seat Ring ASTM A 216 Gr. WCB+13% Cr Steel Facing (Stellited)
9.6 Stem Packing (Renewable Corrosion inhibited die formed flexible
with valve open on stream) graphite with braided anti extrusion rings
9.7 Hand Wheel (Rising) Malleable Iron/ Cast Steel/ Fab. Steel
9.8 Bonnet Bolts A 193 Gr. B7
9.9 Bonnet Nuts A194 Gr. 2H
9.10 Bonnet Gasket Spiral Wound SS 316 + Grafoil
10. Hydrostatic Test Pressure
a) Body : 76 kg/cm2(g)
b) Seat : 57 kg/cm2(g)
11. PnuematicTest Pressure with : 5.6 - 7 kg/cm2 (g).
Air
12. Painting Specifications:
i) Surface preparation by Short Blasting as per grade SA 2 1/2, Swedish Standard SIS-055 909.
ii) For above ground installation-Three coats of corrosion resistant paint shall be applied with minimum thickness of 300 micron
( Permissible thickness in each coat shall be within 80 to 120 micron).
Notes:
1. Valve specification sheet shall be read in conjunction with technical notes for Gate and Globe valves.
2. Valve shall be designed for intrinsically fire safe.
3. Testing shall be as per BS EN 12266-1,approved QAP,this specification and other relevant standards.
4. Bidder shall clearly write all/ any deviation against each part/ material of valve in the space provided for .
Wherever bidder agrees with MECON's data sheet, bidder shall clearly indicate "agreed".
5. Charpy 'V' notch test on each heat of base material shall be conducted for all pressure containing parts such as body, end flange,
welding ends as well as the bolting material as per ASTM A370. The test shall be conducted at 0°C. The minimum average
absorbed energy per set of three specimen shall be 27 J with an individual minimum per specimen of 22 J.
6. Hardness test shall be carried out on each heat of base material for all pressure containing parts of the valve. A full thickness
cross section shall be taken for this purpose and the maximum hardness shall not exceed 248 HV10 based on minimum four
measurements representing the entire thickness.
7. Stem packing shall be renewable with valve open on stream .
8. Painting procedure of the valves shall be as per Manufacturer's Standard.
9. Material Test Certificates and Hydro Test Reports shall be furnished prior to dispatch.
REV. NO. DATE ZONE DESCRIPTIONS BY APPRD
REFERENCES DRG. NO.
SECTION PROCESS & PIPING CLIENT :
NAME DATE CHKD DATE SUPPLIER :
DSGN PM AKJ SUB SUPPLIER : MECON LIMITED
DRWN PROJECT :
SCALE : REV
APPROVED O. P. JAIN DATA SHEET FOR GLOBE VALVES DATA SHEET NO.:MEC/05/21/M/005/DS/GV/77 0
(NB ≥ 2")
