Maxim > App Notes > INTERFACE CIRCUITS

Keywords: RS-485, RS485, RS-422, RS422, EIA/TIA-485, EIA/TIA-422, differential data transmission, full- Mar 16, 2001
duplex, half-duplex, unit load, fractional unit load, EMI, ESD protection, electro-static discharge, electro-
magnetic interference

APPLICATION NOTE 736

RS-485 (EIA/TIA-485) Differential Data Transmission System Basics

Abstract: Electrical specifications are presented for the RS-422 unidirectional, RS-485 full-duplex and PROFIBUS
data transmission systems. Electrostatic discharge (ESD) protection, data rates, and loading conditions are
considered. The concept of fractional unit loading is introduced.

The RS-485 standard was developed jointly by two trade associations: the Electronic Industries Association (EIA)
and the Telecommunications Industry Association (TIA). The EIA once labeled all its standards with the prefix
"RS" (Recommended Standard). Many engineers continue to use this designation, but the EIA/TIA has officially
replaced "RS" with "EIA/TIA" to help identify the origin of its standards. Today, various extensions of the RS-485
standard accommodate a large variety of applications.

The RS-485 and RS-422 standards share many of the same attributes, and are often confused for that reason.
The table below compares the different standards. The RS-485, which specifies bi-directional and half-duplex
data transmission, is the only EIA/TIA standard that allows multiple receivers and drivers in "bus" configurations.
Conversely RS-422 EIA/TIA standard specifies a single, unidirectional driver with multiple receivers. Therefore
RS-485 parts are backward compatible and interchangeable with their RS-422 counterparts. However, RS-422
drivers should not be used in an RS-485 system for they cannot relinquish control of the bus.

RS-485 and RS-422 Standards

RS-422 RS-485 PROFIBUS

Differential Unidirectional Differential Full Duplex Differential Full Duplex
Mode of operation
Multipoint Multipoint Multipoint
Allowed no. of Tx and Rx 1 Tx, 10 Rx 32 Tx, 32 Rx 32 Tx, 32 Rx
Maximum cable length 4000ft length 4000ft length 4000ft length
Maximum data rate 10Mbps 10Mbps 40Mbps
Minimum driver output range ±2V ±1.5V ±2.1V
Maximum driver output range ±5V ±5V ±5V
Maximum driver short-circuit current 150mA 250mA 250mA
Tx load impedance 100Ω 54Ω 54Ω
Rx input sensitivity ±200mV ±200mV ±200mV
Maximum Rx input resistance 4kΩ 12kΩ 12kΩ
Rx input voltage range ±7V -7V to +12V -7V to +12V
Rx logic high >200mV >200mV >200mV
Rx logic low <200mV <200mV <200mV

PROFIBUS

PROFIBUS is a communication standard built upon an RS-485 type transceiver. It is intended for industrial
control networks. The PROFIBUS specification covers the software protocol, the connector type, and a differential
termination network.

ESD Protection

The differential signal paths of RS-485 and RS-422 systems provide reliable data transmission in the presence of
noise and are also capable of rejecting large common-mode voltages. To guard against the much higher voltage
levels associated with electrostatic discharge (ESD), a different class of protection is needed.

The charged capacitance of a human body enables a person to destroy integrated circuits with a single touch.
Such a contact can easily occur during the installation of an interface cable. To prevent ESD damage, Maxim's
interface ICs incorporate "ESD structures." The ESD structures protect the transmitter outputs, receiver inputs,
digital interface connections, and analog connections to the RS-422/RS-485 transceivers against ESD levels up
to ±15kV.

Maxim guarantees the specified ESD protection by repeatedly testing the IC terminals in 200V increments to
verify a sequence of levels up to ±15kV. Devices with this rating (per the Human Body Model or the IEC 1000-4-
2 specification) are designated by an additional "E" suffix on the part number. For more information on ESD
protection, refer to the application note titled "Maxim Leads the Way in ESD Protection".

Data Rates and Driver Loading

The load presented to an RS-485/RS-422 driver is quantified in terms of the unit load, which is defined as the
input impedance for one standard RS-485 receiver (12kΩ). Thus, a standard RS-485 driver is capable of driving
32 unit loads (32 12kΩ loads in parallel) or 375Ω. The input impedance for certain RS-485 receivers is 48kΩ (1/4
unit load) or even 96kΩ (1/8 unit load), and as many as 128 or 256 respective receivers, can be connected to a
single RS-485 bus. Any combination of receiver types can be connected together, provided their parallel
impedance does not exceed 32 unit loads (RLoad > 375Ω).

Consequences of High Data Rates

Faster transmissions require higher slew rates at the driver output, and higher slew rates produce higher levels
of electromagnetic interference (EMI). Some RS-485 transceivers minimize EMI by limiting their slew rates.
Lower slew rates also help to control the reflections caused by fast transitions, high data rates, or long cables.
Essential for minimizing reflections are termination resistors that match the cable's characteristic impedance.
Common RS-485 cables (a twisted pair of 24AWG wires) should be terminated with a 120Ω resistor at both ends.

For more about RS-485 designs, refer to Methods for Trimming the Power Required in RS-485 Systems and
Selecting and Using RS-232, RS-422, and RS-485 Serial Data Standards.

Application Note 736: http://www.maxim-ic.com/an736

More Information
For technical questions and support: http://www.maxim-ic.com/support
For samples: http://www.maxim-ic.com/samples
Other questions and comments: http://www.maxim-ic.com/contact

Related Parts
MAX1480E: QuickView -- Full (PDF) Data Sheet
MAX1490E: QuickView -- Full (PDF) Data Sheet -- Free Samples
MAX3070E: QuickView -- Full (PDF) Data Sheet -- Free Samples
MAX3080E: QuickView -- Full (PDF) Data Sheet -- Free Samples
MAX3157: QuickView -- Full (PDF) Data Sheet -- Free Samples

MAX3440E: QuickView -- Full (PDF) Data Sheet -- Free Samples

MAX3460: QuickView -- Full (PDF) Data Sheet -- Free Samples

MAX3465: QuickView -- Full (PDF) Data Sheet -- Free Samples

AN736, AN 736, APP736, Appnote736, Appnote 736

Copyright © by Maxim Integrated Products
Additional legal notices: http://www.maxim-ic.com/legal