Quick Start Guide

24” / 32” LED HD TV

LT-24C490 / LT-32C490 / LT-32C491

Thank you for purchasing your new JVC TV.

Your new TV incorporates the latest technology to enhance your viewing
experience. We would suggest that you allow about 20 mins for initial setup.
Please follow this guide for a successful first time installation.

The latest eco-friendly power-saving technology will switch off the TV if device is
left on and idle for 4 hours or it does not receive an input signal for serveral minutes.
Please refer to “Eco Friendly / Auto Standby Function” section of the instruction manual
for more detail.

For Help and Support Call

UK: 0344 561 1234
Ireland: 1890 818 575
1 Unpacking
Remove all packaging from the TV. Retain the packaging. If you
dispose of it please do so according to any local regulations.

TV TV Stand Base Screw x 4

TITLE

ASPECT S.MODE P.MODE GUIDE

LIST

MENU INPUT

OK

BACK PROG EXIT

ANGLE
TV.RD

SETUP

FAV

HOLD REVEAL SUBPAGE INDEX

MENU
TEXT S
CANCEL MIX SIZE
OK

AUDIO
ZOOM STEP

GOTO SLOW REPEAT A-B

Remote Control AAA Batteries x 2 Instruction Manual

Quick Start Guide

If items are missing, or damaged please contact Partmaster (UK only).

Tel: 0344 800 3456 for assistance.
2 Operating Your Remote Control
Installing Batteries
1. Press and lift the back
cover to open the
battery compartment of
the remote control.

2. Insert two AAA size

batteries. Close the
battery compartment
cover.

Install the batteries correctly by following the polarity (+ and -) indications in the
battery compartment.

Operation Range
Point the remote control at the TV no
more than 5 metres from the remote
control sensor on the TV and within
60° in front of the TV. The operating
distance may vary depending on the
brightness of the room.

30° 30°
5M
TITLE

ASPECT S.MODE P.MODE GUIDE

LIST

MENU INPUT

OK

BACK PROG EXIT

ANGLE
TV.RD

SETUP

FAV

HOLD REVEAL SUBPAGE INDEX

MENU
TEXT S
CANCEL MIX SIZE
OK

AUDIO
ZOOM STEP

GOTO SLOW REPEAT A-B

3 Installing the Base Stand
1. Lay the TV down on a flat surface with the back side facing up, and ideally at the edge of a table so that the base of the TV slightly overhangs on it. Please
make sure a soft cushioned material (such as a towel or thick piece of foam) is placed beneath the screen. Leave the protective bag on your TV until you
have fully attached the TV stand.
2. Attach the TV stand to the TV. Align the screw holes, then secure with a screw driver (not included) using the 4 screws provided.

TV Stand Base Front

(included)

4 Connecting the Aerial and the Mains Socket

1. Connect one end of the RF coaxial cable to the aerial socket on the wall and the other end of the cable to the RF (75Ω) socket at the rear right side of your
TV.
2. Connect the mains cable to the mains socket after you have completed all the connections.
3. At this stage, the TV switches to standby mode. The red LED indicator will illuminate on the front panel of the TV.
4. In standby mode, press the button at the bottom of the TV or on the remote control to turn the TV on. The red LED indicator will turn off.

OR

RF coaxial cable
(not included)

To the mains socket

1 2
COMMON INTERFACE (CI)

USB

LAN HDMI2 RF HEADPHONES 5V 500mA Digital Output

• Do not connect the TV to the mains supply until you have completed all the connections.
• If you watch TV using a set-top box, simply connect your TV and set-top box via a HDMI cable and select HDMI in the Input Source menu.
5 Turning the TV On for the First Time
The first time you turn the TV on, it will go straight into the First Time Installation menu.

1. Please ensure the aerial is plugged in and then press the OK button.
First Time Installation
Please ensure aerial is plugged in!
If you are going to watch TV using a set-top box, press the EXIT button on the remote control
then skip this section. Then press the INPUT button on the remote control to select HDMI mode.

OK Confirm

2. Press the buttons to select the country where you will operate the TV. Press the
First Time Installation
OK button to confirm.

Country UK
OSD Language English
Home/Store Mode Home Mode
Tune Type DTV
OK Confirm

3. Press the button to select OSD Language, then press the buttons to select
First Time Installation
your desired language to be displayed on the menu. The default on-screen menu
language is set as English. Press the OK button to confirm.
Country UK
OSD Language English
Home/Store Mode Home Mode
Tune Type DTV
OK Confirm

4. Press the button to select Home/Store Mode. Press the buttons to select your
desired mode and then press the OK button. A pop-up message will be displayed. First Time Installation
Press the buttons to select Yes to confirm or No to cancel. Press the OK button to
return to the Mode Select menu. Country UK

Home Mode Intended for use in home environment.

OSD Language English

Shop Mode Intended for use in retail environment.

Home/Store Mode Home Mode
Tune Type DTV
OK Confirm

5. Press the button to select Tune Type, then press the buttons to select DTV /
First Time Installation
ATV / DTV + ATV. Press the OK button to confirm.

Country UK
OSD Language English
Home/Store Mode Home Mode
Tune Type DTV
OK Confirm

6. Channel tuning will commence. This operation may take a few minutes. The display
will show the progress of the tuning and the number of channels found. Channel Tuning

TV 0 Channel(s)
DTV 0 Channel(s)
Radio 0 Channel(s)
Data 0 Channel(s)
DTV UHF 36
6 Target Region Setting (UK only)
During tuning your TV may have received signals from more than one transmitter. If this has occurred the Target Region Setting screen will be displayed. This
will enable you to select the correct regional transmission for the local news service that you require.
1. Press the buttons to select the Country then press the buttons to select Primary
Choose Your Prefered Region
Region / Secondary Region / Tertiary Region.
2. Press the buttons to select your preferred region then press the OK button to confirm. Country UK

Country Code This will be shown as GBR for the UK. Primary Region England
Secondary Region London
Primary Region This will show the regional country (e.g. England, Wales, Scotland, NI).
Tertiary Region Cambridge
This will allow you to set the region for your local news service on BBC and
Secondary Region OK Confirm
ITV (e.g. London, Beds and Cambs etc).

You may receive signals from more than one transmitter within the
Tertiary Region
Secondary Region, (e.g Beds and Cambs may have Luton or Sandy Heath).

Well done, your new TV is now ready to use. You will find that there are many exciting features available. To get to know all these features, please
take some time to read the instruction manual provided with your TV.
If after reading the instruction manual you have additional questions related to the use of your TV please call:
• UK Call Centre on 0344 561 1234. • Ireland Call Center on 1 890 818 575.
(QSG-LT-24C490_32C490_32C491-190823V3)