1/31/2020 Reinforced Concrete Water Tank Design Requirements

🔍 Search 📰 Shop Mer

⌂ Home / Structural Engineering / Structural Design / Reinforced Concrete Water Tank Design Requirements

SPONSORED SEARCHES

how to make concrete water tank size of overhead water tank

underground water reservoir tank water tank rectangular design

Posted in Structural Design, Structural Engineering, Water Tank Design

Reinforced Concrete Water Tank Design Requirements

Reinforced concrete water tanks are constructed for storing water. The design of reinforced concrete water tank is based on IS 3370: 2009 (Par
– IV). The design depends on the location of tanks, i.e. overhead, on ground or underground water tanks.

×
Get Notifications
The tanks can be made in different shapes usually circular and rectangular shapes are mostly used. The tanks can be made of reinforced
concrete or even of steel. The overhead tanks (elevated tanks) are usually elevated from the rooftop through column. In the other hand the
underground tanks are rested on the foundation.

In this article, Design requirements of reinforced concrete water tanks are discussed.

1.Types of RCC water tank

Based on the water tank location and their shapes, they are classified as shown in Table 1:

Table 1 types of RCC water tank based on their location and shapes

SPONSORED SEARCHES

reinforced concrete water tank design

minimum grade of concrete for water tank

types of rcc water tank

minimum reinforcement in water tank

plastic water tank project report



https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 1/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

☰
Types of water tanks

Based on water tank location Based on water tank shape

Underground tanks Rectangular tank

Tank resting on grounds Circular tank

Overhead tanks* Spherical tank

Intze tank

Circular tank with conical bottom

*the aesthetical view of the surroundings and the design of the construction controls shape of the overhead tanks.

×
Get Notifications
Fig.1:above ground RCC water tank

Fig.2:under ground RCC water tank

Fig.3:overhead RCC water tank

2.Basis of concrete water tank design

RCC water tank design should be based on sufficient resistance to cracking to avoid leakage and adequate strength. For achieving these follow

assumptions are made:

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 2/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

Plain section before bending remains plain after bending

Both concrete and steel are perfectly elastic and modular ratio value has a value given in IS 456- Table 21.

In calculation of stresses. Both for flexural and direct tension or combination thereof relating to resistance to cracking, the entire section
concrete including the cover together with reinforcement can be taken into consideration provided that tensile stress in concrete limited
values provided in Table 2.

Neglect concrete tensile strength during strength calculation.

×
Get Notifications
Fig.4:Stresses in a RCC water tank

3.Permissible stress on concrete

Permissible stress for resistance of cracking
Water tank concrete shall be free of leakage. This may be achieved by selecting concrete M 20 grade and greater, and concrete near water face
need to such that no crack occurs.

So, to make concrete crack free at water face, water tank wall thickness shall be designed so that stress on concrete is smaller than values
provided in Table 2.

In members less than 225mm. thick and in contact with liquid on one side these permissible stresses in bending apply also to the face remote
from the liquid.

Table 2 Permissible Stresses in Concrete (For calculations relating to resistance to concrete)

Permissible Concrete Stresses

Grade of Concrete
Direct Tension N/mm2 Tension due to bending N/mm2


M15 1.1 1.5

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 3/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

M20 1.2 1.7

☰

M25 1.3 1.8

M30 1.5 2.0

M35 1.6 2.2

M40 1.7 2.4

Permissible stress for strength calculation

In strength calculation, permissible concrete stresses should be in accordance with values provided in Table 3 and Table 4.

Table 3 permissible stresses in concrete for strength calculation

×
Get Notifications
Permissible stress in compression, N/mm2
Permissible stress in bond (Average) for plain bars in
Grade of concrete
tension, N/mm2
Direct Bending

M25 6 8.5 0.9

M30 8 10 1

M35 9 11.5 1.1

M40 10 13 1.2

M45 11 14.5 1.3

M50 12 16 1.4

Table 4 Permissible shear stress in concrete

Permissible shear stress in concrete, N/mm2

100*As/bd
M25 M30 M35 M40 and above

?0.15 0.19 0.20 0.200 0.20

0.25 0.23 0.23 0.230 0.23



https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 4/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

0.50 0.31 0.310 0.31 0.32

☰
0.75 0.36 0.37 0.37 0.38

1 0.40 0.41 0.42 0.42

1.25 0.44 0.45 0.45 0.46

1.50 0.46 0.48 0.49 0.49

1.75 0.49 0.50 0.52 0.52

2 0.51 0.53 0.54 0.55

2.25 0.53 0.55 0.56 0.57

2.50 0.55 0.57 0.58 0.60

2.75 0.56 0.58 0.60 0.62

3 and above 0.57 0.60 0.62 0.63

As: longitudinal tension reinforcement area

4.Permissible stress in steel

×
Get Notifications
The stress in steel must not be allowed to exceed the following values under different positions to prevent cracking of concrete.

When steel is placed near the face of the members in contact with liquid 115 N/mm2 for mild steel Bars and 150 N/mm2 for high strength

deformed bars.

If steel is placed on the face away from the liquid for members 225 mm or more in thickness then permissible stress in steel shall be 125
mm2 for mild steel bars and 190 N/ mm2 for high strength deformed bars.

When steel is placed on face away from liquid for members less than 225 mm in thickness same as earlier.

Fig.5:Reinforcement in water tanks

5. Stress due to temperature or moisture variations 

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 5/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

It is not required to perform separate calculation for stress due to moisture and temperature variation in concrete provided that the following
☰
conditions are met:

The reinforcement provided is not less than minimum reinforcement which described in the sections below.

IS 3370 (Part 1) recommendations regarding movement joint provisions and for a suitable sliding layer beneath the water tank are execu
properly.

The tank shall be applied for the storage of water or aqueous liquids at or near surrounding temperature

concrete shall never dry out.

Suitable measures are taken to prevent cracking of the concrete during the construction period and until the tank is put into use.

Nonetheless, separate computation for moisture and temperature variation shall be conducted if:

Assumed shrinkage coefficient is .

Permeable lining used for the water tank. In this case, possible dry out of the tank shall be taken into consideration.

Note: cement content with a range from 330Kg/m3 to 550Kg/m3 shall be used to reduce shrinkage to as minimum as possible.

6. Floors of Reinforced Concrete Water Tank

Movement joints
Movement joints should be provided in accordance with IS 3770 (part I)

×
Get Notifications
Fig.6:Various movement joints in water tank floor

Floor of RCC water tank rest on the ground

Place layer of lean concrete not less than 75 mm thick over the ground.

Commonly, use M15 for lean concrete

Employ M20 for lean concrete in the presence of aggressive soils or harmful water

Consider sulfate resisting concrete if required

Install polyethylene sheet layer between lean concrete and the floor

Cast the floor in single layer

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 6/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

Fig.7:Reinforced concrete water tank floor above ground

Floor of tanks rest on support

It should be designed for bending moments due to dead load and water load.

Special attention shall be practice during the design of floor of multi-cell water tank

Lastly, when walls and floor are connected rigidly, then moment at the junction in combination with other transferred loads shall be
considered in floor design.

×
Get Notifications
Fig.8:above head water tank floor

7. Concrete Water Tank Walls

Provision of joints
sliding joints may be used if:

It is desired to permit the walls to expand or contract separately from the floor.

To prevent moments at the base of the wall because of fixity to the floor.


Fig.9:Sliding joint in water tank

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 7/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

☰
Pressure on RCC water tank wall
gas pressure, which is developed due to the presence of fixed or floated tank cover, shall be added to the liquid pressure.

When water tank constructed in ground or earth embanked against it, then earth pressure shall be accounted in wall design.

Fig.10:Earth fill imposed earth pressure on RCC water

tank wall

8. RCC water tank roof

To avoid the possibility of sympathetic cracking it is important to ensure that movement joints in the roof correspond with those in the walls, i
roof and walls are monolithic.

×
Get Notifications
However, provision is made by means of a sliding joint for movement between the roof and the wall, Correspondence of joints is not so
important.

Moreover, in case of tanks intended for the storage of water for domestic purpose, the roof must be made water-tight.

This may be achieved by limiting the stresses as for the rest of the tank, or by the use of the covering of the waterproof membrane or by
providing slopes to ensure adequate drainage.

Fig.11:RCC water tank roof

9. Minimum reinforcement for RCC water tank

Minimum reinforcement required for 199mm thick sections is 0.3 % of the area of concrete section which reduced linearly to 0.2% for 450 mm
thick sections.

Moreover, in case of floor slab for tank resting on ground the minimum reinforcement from practical consideration should not be less than 0.3
of the gross sectional area of the floor slab.

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 8/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

Finally, if the thickness of the section (wall, floor or roof slab of the tank) works out to be 225 mm and above two layers of reinforcing steel sha
☰
be placed, one near each of the section to make up the minimum reinforcement requirements.

 Share This Article  Facebook   

Madeh Izat Hamakareem ✓

×
Get Notifications
Madeh is a Structural Engineer who works as Assistant Lecturer in Koya University. He is the author, editor and partner at theconstructor.org.

← Previous article

Reinforcement Detailing of Reinforced Concrete Slabs

Next article

Planning of a Construction Pro

Related Posts

Euler's Theory of Column Buckling Pre-Engineered Steel Building - Components and Advantage

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 9/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

ATLAS Weathering Design of Reinforced Worlds Leading Sump Water Tank Design
Instruments Concrete Wall - Repair - Fittings-
Guidelines, Concept,… cracks-holes-covers

Ad www.atlas-mts.com theconstructor.org Ad icontainment.com theconstructor.org

Become an SAP 450+hrs of Online Design of Rectangular Reinforced Concrete

Consultant Training Reinforced Concrete Slab Design and
Beam Detailing Guide…

Ad TimesPro Ad www.edureka.co theconstructor.org theconstructor.org

10 Comments

Yogesh Joshi

Added a comment on September 30, 2014 at 12:01 pm

good guide for learner

🔒 Login to Reply  Share

×
Get Notifications
Lateef Lawal

Added a comment on September 13, 2014 at 7:33 am

good

🔒 Login to Reply  Share

Costantine Tungaraza

Added a comment on August 6, 2014 at 5:48 am

good work

🔒 Login to Reply  Share

Costantine Tungaraza

Added a comment on August 5, 2014 at 7:02 am



https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 10/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

thanks for good selection

☰
🔒 Login to Reply  Share

Santhanam Velayutham

Added a comment on July 31, 2014 at 6:23 am

a good guide for design

🔒 Login to Reply  Share

Uday Ramteke

Added a comment on May 5, 2014 at 10:13 pm

Hmmm… How Much o.O ..??

🔒 Login to Reply  Share

Murtza Ahmed S

Added a comment on November 16, 2013 at 3:14 am

thanks

×
Get Notifications
🔒 Login to Reply  Share

Shiba Nanda Mridha

Added a comment on September 28, 2013 at 6:01 pm

more improvement divn

🔒 Login to Reply  Share

Aki Pandey

Added a comment on September 27, 2013 at 6:21 pm

nice

🔒 Login to Reply  Share

Marzok Boles

Added a comment on September 27, 2013 at 4:52 pm

wer drawing of tanks and rainforced of it

🔒 Login to Reply  Share

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 11/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

☰
Leave a comment

You must login or register to add a new comment.

Login with:

Secured by OneAll Social Login

×
Get Notifications

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 12/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

×
Get Notifications

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 13/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

×
Get Notifications

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 14/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

×
Get Notifications

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 15/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

×
Get Notifications

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 16/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

×
Get Notifications

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 17/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

×
Get Notifications

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 18/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

×
Get Notifications

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 19/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements

×
Get Notifications
📖 Popular Articles

Concrete Mix Design

Calculation for M20, M25, M30
Concrete with

Calculate Quantities of
Materials for Concrete -
Cement, Sand, Aggregates

Quantity of Cement and Sand

Calculation in Mortar

Preparation of Bar Bending

Schedule (BBS) and Its
Advantages 

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 20/21
1/31/2020 Reinforced Concrete Water Tank Design Requirements
Civil Engineering Tips - Points
☰ to Remember for Civil Site

📖 Recent Articles

Cost Estimation of
Construction Projects

Engineering Hydrology -
Features and Applications

Water Requirement of Crops -

Delta and Duty of Water

Techniques of Water
Distribution in Irrigation
Engineering

Contractor Roles and

Responsibilities in
Construction

Popular Answers

×
Get Notifications
What are the difference
between Tender and Contract
Documents?

What are Bearing Capacity

Values of Different Types of
Soil?

What should be Minimum

Ceiling Height for a Large
Bedroom?

fly Ash Percentage in PPC

Cements

Which Softwares are used to

Estimate Project Time and
Quantity in Construction?

About Us - Contact Us -

Privacy Policy

© 2009-2020 The Constructor. All Rights

Reserved.

https://theconstructor.org/structural-engg/rcc-water-tank-design-requirements/6717/ 21/21