CROUSE-HINDS

MEDC signalling and alarms SERIES

BG2 range
manual call point
Ex de, Ex ia, weatherproof

Overview Features
This manual fire alarm call point has • Zone 0, Zone 1 and Zone 2 use • Corrosion resistant red painted
been designed for use in flammable GRP
atmospheres and harsh • Ex de, Ex ia or weatherproof
• Retained stainless steel cover
environmental conditions. • ATEX approved - Ex II 1GD (Ex ia) screws
The GRP enclosure is suitable for - Ex II 2GD (Ex de) • Optional lift flap
use offshore or onshore where
lightweight combined with a high • IP66 and IP67 • Key operated test facility
level of corrosion resistance is • Certified temperature from -40°C • Lightweight and robust
required. to +70°C*

*Model dependent

Eaton
Unit B, Sutton Parkway
Oddicroft Lane
Sutton in Ashfield
United Kingdom © 2019 Eaton
NG17 5FB All Rights Reserved
Printed in UK Eaton is a registered trademark.
T: +44 (0) 1623 444 400 Publication
www.crouse-hinds.com/hac No.DSMC0006/B All other trademarks are property
[email protected] May 2019 of their respective owners.
All specifications, dimensions, weights and tolerances are nominal (typical) and Eaton reserve the right to vary all data without prior notice.
No liability is accepted for any consequence of use.
 Certifications General arrangement drawing (all dimensions in mm)
ATEX Ex de Cert. no. BAS02ATEX2105X. ATEX Approved Ex II 2GD
Certified to: EN60079-0, EN60079-1, EN60079-7, EN60079-18, EN60079-31
Ex db eb IIC T6 Gb, Ex tb IIIC T85°C Db (switch only)
Ex db eb mb IIC T4 Gb, Ex tb IIIC T135°C Db (with resistors & diodes)
ATEX Ex ia Cert no. Baseefa 03ATEX0084X. ATEX Approved Ex II 1 GD
Certified to: EN60079-0, EN60079-11
Ex ia IIC T4 Ga, Ex ia IIIC T135°C Da
Specifications
Material Anti static UV resistant glass reinforced polyester
Finish Painted red
Certified temp -40°C to +70°C
Voltage Up to 250Vac. Up to 50Vdc (model dependent)
Weight 1.2Kg
Ingress protection IP66 and IP67
Cable entries 2 x M20 bottom
Terminals 6 x 2.5 mm²
Resistors values Ex de - 100Ω minimum, 39 KΩ maximum
Ex ia - 470Ω minimum
Switch ratings Switch only 30Vdc 5A (resistive) or 3A (inductive)
30-50Vdc 1A (resistive or inductive)
250Vac 5A (resistive or inductive)
Resistor(s) 24Vdc 0.05A

ALL CIRCUITS SHOWN WITH GLASS INTACT

Ordering requirements
The following code is designed to help in selection of the correct unit. Build up the reference number by inserting the code for each component into the appropriate box

Model Options Flap Finish

Model Code Options Code Flap Code Finish Code

BG2W - ac or dc BG2WNN Switch only 1 Fitted F* Red painted R
BG2I - Up to 28V (I.S.) BG2INN End of line resistor 2* Not fitted N
BG2E - dc BG2EDC In line resistor 3* *Polycarbonate lift flap
BG2E - ac BG2EAC In line and end of line resistor 4*
Diode (specify location & value) 5
*Specify resistor values

The Eaton BG range of manual alarm call point caters for numerous
options such as variety of colours, LED indication, earth continuity,
double switch, etc. See separate catalogue sheet for details

DSMC0006/B 05/19
 DO NOT SCALE

120 2 75 2 1. TYPE BG2E/I/W

2. CERTIFICATION:
BG2E:
ATEX: Baseefa02ATEX2105X
STANDARD: Ex de IIC T6 Gb (-40 $ C to +70 $ C)
Ex tb IIIC T85 $ C Db IP66/67 (-40 $ C to +70)

72 # 1 RESISTOR/DIODE: Ex de mb IIC T4 Gb (-40 $ C to +70 $ C)

Ex tb IIIC T135 $ C Db IP66/67 (-40 $ C to +70)
126 2 FIXING
CENTRES
BG2I:
ATEX: Baseefa03ATE0084X
II 1 GD Ex ia IIC T4 Ga (-40 $ C to +70 $ C)
Ex ia IIIC T135 $ C Da (-40 $ C to +70 $ C)

BG2W: INDUSTRIAL

3. WEIGHT: 1.2 # 0.2Kg

4. MATERIAL: GLASS REINFORCED POLYESTER
5. FUNCTION LABEL LETTER SIZE 5mm MAX.
25 # 1
6. OPTIONAL CLEAR POLYCARBONATE LIFT FLAP
1 2 GLAND
AVAILABLE ON REQUEST
67 2 CENTRE
2
7. TERMINAL SUITABLE FOR UP TO 2.5MM CABLE
16 1 16 1
8. 2 x M20 CABLE ENTRIES AVAILABLE AT

92 # 1 POSITIONS '1' & '2'

FIXING CENTRES
Cooper MEDC Ltd, Unit B, Sutton Parkway,
Oddicroft Lane, Sutton-in-Ashfield, DESIGNERS & MANUFACTURERS
OF ELECTRICAL & ELECTRONIC
Nottinghamshire, NG17 5FB, U.K.
FIXING HOLES: n 6.0 (4 POSITIONS) EQUIPMENT & SYSTEMS FOR
Tel:+ 44 (0) 1623 444400 HAZARDOUS AREAS
web: www.coopermedc.com

THIS DRAWING IS CONFIDENTIAL DRAWN BY: DATE: TITLE

ALL DIMENSIONS ARE AND IS THE PROPERTY OF MEDC P.FISHWICK 03-04-14
IN MILLIMETRES UNLESS
CHECKED BY: DATE:
OTHERWISE STATED AND MUST NOT BE REPRODUCED BG2E/I/W ATEX
B. 03-06-16 PF
ISSUES

D.COATES 03-04-14
EITHER WHOLLY OR PARTLY. CUSTOMER GA
APPROVED BY: DATE:
REMOVE ALL BURRS
ALL RIGHTS IN RESPECT OF
AND SHARP CORNERS P.FISHWICK 03-04-14
PATENTS, DESIGNS AND
DRG No.
A4
SCALE: SIZE: ISSUE
MACHINE
SYMBOLS THUS COPYRIGHT ARE RESERVED 480-366 B
 DO NOT SCALE

CURRENT

PRODUCTION COPY

MEDC, Colliery Road, Pinxton, DESIGNERS & MANUFACTURERS

Nottingham NG16 6JF, U.K. OF ELECTRICAL & ELECTRONIC
Tel: +44 (0)1773 812249 EQUIPMENT & SYSTEMS FOR
fax: +44 (0)1773 580282 HAZARDOUS AREAS
ALL DIMENSIONS ARE DRAWN BY: DATE: TITLE
IN MILLIMETRES UNLESS THIS DRAWING IS CONFIDENTIAL
OTHERWISE STATED AND IS THE PROPERTY OF MEDC
CHECKED BY: DATE:
AND MUST NOT BE REPRODUCED
REMOVE ALL BURRS EITHER WHOLLY OR PARTLY.
AND SHARP EDGES APPROVED BY: DATE:
ALL RIGHTS IN RESPECT OF
PATENTS, DESIGNS AND
MACHINE SCALE: SIZE DRG No. ISSUE
COPYRIGHT ARE RESERVED.
SYMBOLS THUS µm A4
 Certificate Number Issued 1 November 2021
BAS21UKEX0544X Page 1 of 4

1 UK-TYPE EXAMINATION CERTIFICATE

2 Equipment or Protective System Intended for use in Potentially Explosive Atmospheres
UKSI 2016:1107 (as amended) – Schedule 3A, Part 1
3 UK-Type Examination BAS21UKEX0544X
Certificate Number:
4 Product: Break Glass Unit -BGE, BG2E & PBE
5 Manufacturer: Eaton MEDC Limited
6 Address: Unit B, Sutton Parkway, Oddicroft Lane, Sutton-in-Ashfield, NG17 5FB
7 This product and any acceptable variation thereto is specified in the schedule to this certificate and the documents
therein referred to.
8 SGS Baseefa, Approved Body number 1180, in accordance with Regulation 43 of the Equipment and Protective
Systems Intended for Use in Potentially Explosive Atmospheres Regulations 2016, UKSI 2016:1107 (as amended),
certifies that this product has been found to comply with the Essential Health and Safety Requirements relating to the
design and construction of products intended for use in potentially explosive atmospheres given in Schedule 1 of the
Regulations.
The examination and test results are recorded in confidential Report No. 21(C)0385
9 Compliance with the Essential Health and Safety Requirements has been assured by compliance with:
EN IEC 60079-0: 2018 EN 60079-1: 2014 EN IEC 60079-7: 2015 + A1: 2018 EN 60079-18: 2015
EN 60079-31: 2014
except in respect of those requirements listed at item 18 of the Schedule.
10 If the sign “X” is placed after the certificate number, it indicates that the product is subject to the Specific Conditions
of Use specified in the schedule to this certificate.
11 This UK-TYPE EXAMINATION CERTIFICATE relates only to the design and construction of the specified product.
Further requirements of the Regulations apply to the manufacturing process and supply of this product. These are not
covered by this certificate.
12 The marking of the product shall include the following:

See Schedule

SGS Baseefa Customer Reference No. 0676 Project File No. 21/0385

This document is issued by the Company subject to its General Conditions for Certification Services accessible at http://www.sgs.com/en/Terms-and-
Conditions.aspx and the Supplementary Terms and Conditions accessible at http://www.sgs.com/SGSBaseefa/Terms-and-Conditions.aspx. Attention is
drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained
herein reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. It does not necessarily indicate
that the equipment may be used in particular industries or circumstances. The Company’s sole responsibility is to its Client and this document does not
exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced
except in full, schedule included, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or
appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

SGS Baseefa Limited

Rockhead Business Park, Staden Lane,
Buxton, Derbyshire SK17 9RZ
Telephone +44 (0) 1298 766600 Fax +44 (0) 1298 766601
e-mail [email protected] web site www.sgs.co.uk/sgsbaseefa
Registered in England No. 4305578. R S SINCLAIR
Registered address: Rossmore Business Park, Ellesmere Port, Cheshire, CH65 TECHNICAL MANAGER
3EN 0191 On behalf of SGS Baseefa Limited
BAS-CertUK-001 SGS Fimko OY is an associate of SGS Baseefa Limited
Issue 2
 Certificate Number Issued 1 November 2021
BAS21UKEX0544X Page 2 of 4

13 Schedule
14 Certificate Number BAS21UKEX0544X

15 Description of Product
The BGE, BG2E and PBE models are non-metallic enclosure, containing separately certified rail or direct mount terminals and
optionally fitted separately certified encapsulated resistors and diode assemblies. (See Table 4 below.)

Models BGE and BG2E utilise a top shell with an external recess, which houses an emergency break glass pane, in which the
release actuator is housed. Optionally, a separately certified LED indicator assembly may be fitted.

Model PBE utilise a top shell with a mounted push-button momentary-release or latching actuator; optionally, a separately
certified LED indicator assembly may be fitted.

All models provide an ingress protection levels of IP66 and IP67 and internal and optional external earthing facilities. Refer to
certificate annex for electrical supply ratings and list of permitted separately certified devices.

Table 1
Maximum Electrical Supply Ratings
Units fitted with up to 2 micro switches
Voltage d.c. Resistive load Amps Inductive load Amps
30 5 3
50 1 1
75 0.75 0.75
125 0.5 0.03
250 0.25 0.03
Voltage a.c. Resistive load Amps Inductive load Amps
125 5 5
250 5 5

Table 2
Units fitted with the encapsulated resistors/LED
Maximum Electrical Supply Ratings based on devices fitted.
LED: 24VDC 30 mA
Resistor/Diode: 1.2W max per resistor or diode fitted.
Voltage Current
6 VDC 200 mA
24 VDC 50mA
48 VDC 25mA
60 VDC 20mA
80 VDC 15mA

BAS-CertUK-001 SGS Fimko OY is an associate of SGS Baseefa Limited

Issue 2
 Certificate Number Issued 1 November 2021
BAS21UKEX0544X Page 3 of 4

Table 3
Minimum Resistor
Values

R1Min R2Min

A 100 Ω 180 Ω

B 250 Ω 47 Ω

Table 4
ASSOCIATED CERTIFIED ELECTRICAL COMPONENTS
The following certified components may be incorporated into the equipment
Certificate No. IECEx/ATEX Description Manufacturer Type Designation
BAS01ATEX2358U Micro Switch SAIA-Burgess E1V3CS/XXXX
Baseefa13ATEX0067U Encapsulated LED and Eaton MEDC Encapsulated
Resistor Units Resistor/Diode assembly
TUV 18 ATEX 8221U Terminal Weidmuller AKZ 4
AKZ 2.5
TUV 18 ATEX 8209U Terminal Weidmuller BK 6/E

KEMA03ATEX2380U Terminal Phoenix MBK2.5/E

The terminals as listed in Table 4 above, are reviewed against the latest requirements of EN IEC 60079-0:2018 and EN 60079-
7:2015 and are considered suitable for the assembly.
In addition the AKZ 4 AKZ 2.5 and BK 6/E terminals show compliance with EN IEC 60079-7:2015+A1:2018
All models are permitted to be fitted with type BK6/E terminal strip as detailed in Table 4.

ELECTRICAL SUPPLY RATINGS

a) For versions which are equipped with up to two micro switches only – the maximum values for each switch fitted are
as specified in table 1.
b) For versions which are equipped with encapsulated housing – the maximum system values are detailed in table 2
together with alternative resistor values and electrical ratings in Table 3.
MARKING: Models BGE, BG2E, PBE
LEDs Resistors LEDs & Resistors Switches only

II 2 GD II 2 GD II 2 GD II 2 GD

Ex db eb mb IIC T6 Gb Ex db eb mb IIC T4 Gb Ex db eb mb IIC T4 Gb Ex db eb IIC T6 Gb
Ex tb IIIC T85°C Db Ex tb IIIC T135°C Db Ex tb IIIC T135°C Db Ex tb IIIC T85°C Db
IP66/67 IP66/67 IP66/67 IP66/67
(Tamb = -35°C to +70°C) (Tamb = -40°C to +70°C) (Tamb = -35°C to +70°C) (Tamb = -40°C to +70°C)

16 Report Number
SGS Baseefa Certification Report 21(C)0385

BAS-CertUK-001 SGS Fimko OY is an associate of SGS Baseefa Limited

Issue 2
 Certificate Number Issued 1 November 2021
BAS21UKEX0544X Page 4 of 4

17 Specific Conditions of Use

1. The units must be incorporated in systems which limit the electrical supply ratings to the values above.
2. The wiring loom between the fixed and detachable enclosure shell must be located during assembly such that the
conductors and the restraint loop are not trapped in the sealing face between the shells.
3. Cable glands installed on the PBE, BGE and BG2E models are to be provided with sealing washers to maintain the
IP66 rating of the enclosure.
4. The encapsulated LED and encapsulated resistor/diode units shall be protected by a fuse rated for a prospective short
circuit current of at least 1500A.

18 Essential Health and Safety Requirements

In addition to the Essential Health and Safety Requirements (EHSRs) covered by the standards listed at item 9, the following
are considered relevant to this product, and conformity is demonstrated in the report:
Clause Subject

1.2.7 LVD type requirements

1.2.8 Overloading of equipment (protection relays, etc.)

1.4.2 Aggressive substances, etc.

19 Drawings and Documents

Number Sheet Issue Date Description

480-775 1 of 1 A 18/08/21 BGE/BG2E Breakglass UKEX Cert Label

480-776 1 of 1 A 18/08/21 PBE Push Button UKEX Cert Label
IECEx BAS 18.0100X
BAS02ATEX2105X

BAS-CertUK-001 SGS Fimko OY is an associate of SGS Baseefa Limited

Issue 2
 Certificado de
Conformidade
Certificate of Conformity
Reconhecer que o Solicitante / Acknowledge that the Certificate
Holder

CROUSE HINDS COMÉRCIO DE

PRODUTOS ELÉTRICOS LTDA.
Certificado/Certificate avaliou o produto / has had
UL-BR 15.0936X / 00

Revisão/Review Ponto de Chamada Manual e Botoeira

06 com Quebra de Vidro / Break Glass and
Push Button Manual Call Points
Emissão/Issue o qual atende aos requisitos do Programa de Certificação ou
26 de abril de 2016 Portaria / evaluated and meets the requirements of the
April 26, 2016 Certification Program or Decree

Validade/Expiration Portaria INMETRO no. 115:2022

25 de abril de 2028
April 25, 2028
INMETRO Ordinance no. 115:2022
e pode ostentar o Selo de Identificação da Conformidade do Sistema
Brasileiro de Avaliação da Conformidade (SBAC) sobre o(s) produto(s)
relacionado(s) neste certificado. / and can display the Conformity
Identification Seal of the Brazilian Conformity Assessment System
(SBAC) on the product(s) listed in this certificate.

Digitally signed by
RAFAEL DE OLIVEIRA
Rafael Parada PARADA:32218566877
Program Owner Date: 2025.04.30 17:33:56
-03'00'

UL do Brasil Certificações, organismo acreditado pela Coordenação

Geral de Acreditação do INMETRO – CGCRE, segundo o registro Nº
OCP-0029./ UL do Brasil Certificações, Certification Body accredited by
Coordenação Geral de Acreditação do INMETRO - CGCRE according to
the register Nr OCP-0029.

Página/Page: 1 / 9

Certificado de conformidade válido somente acompanhado das páginas de 1 a 9 © 2023 UL LLC. All rights reserved.
Certificate of Conformity valid only if accompanied from pages 1 to 9 Form-ULID-017660 – Rev. 3.0
 Certificado de Conformidade
Certificate of Conformity
Certificado/Certificate: UL-BR 15.0936X / 00
Emissão/Issue Revisão/Review: 06 Validade/Expiration
26 de abril de 2016 25 de abril de 2028
April 26, 2016 April 25, 2028

Solicitante/Certificate holder Crouse Hinds Comércio de Produtos Elétricos Ltda

Party number 1229739 Rod. Marechal Rondon SN KM 125 Parte D. Avecuia
Porto Feliz – SP – 18546-412 – Brasil
CNPJ: 00.142.341/0004-44

Fabricante/Manufacturer Eaton MEDC Ltd.

Party number 643453 Unit B, Sutton Parkway, Oddicroft Lane, Sutton-In-Ashfield, NG17 5FB GB
CNPJ: Não aplicável / Not applicable

Modelo de certificação/ 5
Certification model

Norma(s) aplicável(is)/ ABNT NBR IEC 60079-0:2020 Versão Corrigida:2024

Applicable standards ABNT NBR IEC 60079-1:2016 Versão Corrigida:2020
ABNT NBR IEC 60079-7:2018 Versão Corrigida:2022
ABNT NBR IEC 60079-18:2020
ABNT NBR IEC 60079-31:2014 Versão Corrigida:2021

Identificação UL/ BR3821 / Vol.1 / Sec.1

UL identification

Identificação do modelo de produto(s) certificado(s)/Identification of the model of certified product(s):

Marca/ Modelo/ Descrição/ Código de barras/
Brand name Model Description Bar code number
EATON BGE
Ponto de Chamada Manual e Botoeira com Quebra de Vidro
EATON BG2E N/A
Break Glass and Push Button Manual Call Points
EATON PBE

Os modelos BGE, BG2E e PBE são invólucros não metálicos, contendo terminais de montagem direta em trilho ou BK6
separadamente certificados e opcionalmente instalados com resistores e conjuntos de diodos encapsulados certificados
separadamente.

Os modelos BGE e BG2E utilizam um invólucro com um recesso externo, que abriga uma janela de vidro de ruptura de
emergência, na qual o atuador está alojado. Opcionalmente, pode ser montado com um conjunto de LED indicador
certificado separadamente.

O Modelo PBE utiliza um invólucro montado com um botão de pressão de liberação momentânea ou trava de atuação.
Opcionalmente, pode ser montado com um conjunto de LED indicador certificado separadamente.

Todos os modelos possuem grau de proteção IP66 e IP67 e são fornecidos com terminais de aterramento interno e
externo.

Consulte o item “CARACTERÍSTICAS ELÉTRICAS” a seguir para determinação dos valores da alimentação de energia
elétrica e para a lista de dispositivos certificados separadamente permitidos.
The BGE, BG2E and PBE models are non-metallic enclosure, containing separately certified rail or BK6 direct mount terminals and optionally fitted
separately certified encapsulated resistors and diode assemblies.

Models BGE and BG2E utilize a top shell with an external recess, which houses an emergency break glass pane, in which the actuator is housed.
Optionally, a separately certified LED indicator assembly may be fitted.

UL do Brasil Certificações – CNPJ 04.830.102/0001-95

Av. Engenheiro Luís Carlos Berrini, 105 – 23º Andar
Página/Page: 2 / 9
São Paulo – SP – Brasil - 04571-010 – https://latam.ul.com/
Form-ULID-017660 – Rev. 3.0
 Certificado de Conformidade
Certificate of Conformity
Certificado/Certificate: UL-BR 15.0936X / 00
Emissão/Issue Revisão/Review: 06 Validade/Expiration
26 de abril de 2016 25 de abril de 2028
April 26, 2016 April 25, 2028

Model PBE utilize a top shell with a mounted push-button momentary-release or latching actuator; optionally, a separately certified LED indicator assembly
may be fitted.

All models provide an ingress protection levels of IP66 and IP67 and internal and external earthing facilities.

Refer to ELECTRICAL CHARACTERISTICS for electrical supply ratings and list of permitted separately certified devices.

MARCAÇÃO Ex / Ex MARKING:
Modelos BGE, BG2E e PBE fornecidos com LEDs:
Ex db eb mb IIC T6 Gb
Ex tb IIIC T85°C Db IP66
Tamb = -35°C a +70°C

Modelos BGE, BG2E e PBE fornecidos com Resistores:

Ex db eb mb IIC T4 Gb
Ex tb IIIC T135°C Db IP66
Tamb = -40°C a +70°C

Modelos BGE, BG2E e PBE fornecidos com LEDs e Resistores:

Ex db eb mb IIC T4 Gb
Ex tb IIIC T135°C Db IP66
Tamb = -35°C a +70°C

Modelos BGE, BG2E e PBE fornecidos somente com interruptores (sem LEDs ou Resistores):
Ex db eb IIC T6 Gb
Ex tb IIIC T85°C Db IP66
Tamb = -40°C a +70°C

BGE, BG2E and PBE models fitted with LEDs:

Ex db eb mb IIC T6 Gb
Ex tb IIIC T85°C Db IP66/IP67
Tamb = -35°C to +70°C

BGE, BG2E and PBE models fitted with Resistors:

Ex db eb mb IIC T4 Gb
Ex tb IIIC T135°C Db IP66/IP67
Tamb = -40°C to +70°C

BGE, BG2E and PBE models fitted with LEDs and Resistors:
Ex db eb mb IIC T4 Gb
Ex tb IIIC T135°C Db IP66/IP67
Tamb = -35°C to +70°C

BGE, BG2E and PBE models fitted only with Switches (no LEDs or Resistors):
Ex db eb IIC T6 Gb
Ex tb IIIC T85°C Db IP66/IP67
Tamb = -40°C to +70°C

UL do Brasil Certificações – CNPJ 04.830.102/0001-95

Av. Engenheiro Luís Carlos Berrini, 105 – 23º Andar
Página/Page: 3 / 9
São Paulo – SP – Brasil - 04571-010 – https://latam.ul.com/
Form-ULID-017660 – Rev. 3.0
 Certificado de Conformidade
Certificate of Conformity
Certificado/Certificate: UL-BR 15.0936X / 00
Emissão/Issue Revisão/Review: 06 Validade/Expiration
26 de abril de 2016 25 de abril de 2028
April 26, 2016 April 25, 2028

CARACTERÍSTICAS ELÉTRICAS / ELECTRICAL CHARACTERISTICS:

Tabela 1 / Table 1
Valores Máximos da Alimentação Elétrica
Maximum Electrical Supply Ratings

Unidades instaladas com até 2 micro switches

Corrente / Current
Tensão / Voltage
Carga Resistiva / Resistive Load Carga Indutiva / Inductive Load
(Vcc/dc)
(A) (A)
30 5,00 3,00
50 1,00 1,00
75 0,75 0,75
125 0,50 0,03
250 0,25 0,03
Tensão/ Voltage Carga Resistiva / Resistive Load Carga Indutiva / Inductive Load
(Vca/ac) (A) (A)
125 5,00 5,00
250 5,00 5,00

Tabela 2 / Table 2
Unidades fornecidas com resistores/LED encapsulados
Units fitted with encapsulated resistors/LED
Valores Máximos da Alimentação Elétrica com base nos dispositivos instalados.

LED: 24 VCC 30 mA

Resistor/Diodo: 1,2 W max. por resistor ou diodo montado.

Maximum Electrical Supply Ratings based on devices fitted.

LED: 24VDC 30 mA

Resistor/Diode: 1.2W max per resistor or diode fitted.

Tensão / Voltage Corrente / Current
6 Vcc/dc 200 mA
24 Vcc/dc 50 mA
48 Vcc/dc 25 mA
60 Vcc/dc 20 mA
80 Vcc/dc 15 mA

UL do Brasil Certificações – CNPJ 04.830.102/0001-95

Av. Engenheiro Luís Carlos Berrini, 105 – 23º Andar
Página/Page: 4 / 9
São Paulo – SP – Brasil - 04571-010 – https://latam.ul.com/
Form-ULID-017660 – Rev. 3.0
 Certificado de Conformidade
Certificate of Conformity
Certificado/Certificate: UL-BR 15.0936X / 00
Emissão/Issue Revisão/Review: 06 Validade/Expiration
26 de abril de 2016 25 de abril de 2028
April 26, 2016 April 25, 2028

Tabela 3 / Table 3
COMPONENTES ELÉTRICOS CERTIFICADOS ASSOCIADOS
ASSOCIATED CERTIFIED ELECTRICAL COMPONENTS

Os seguintes componentes certificados podem ser incorporados ao equipamento:

The following certified components may be incorporated into the equipment:

Certficado No. IECEx/ATEX Descrição Fabricante Designação de Tipo

Certificate No. IECEx/ATEX Description Manufacturer Type Designation

IECEx BAS 17.0070U Micro interruptor SAIA-Burgess E1V3CS/XXXX

Micro Switch
Unidades LED e Resistores Montagem Encapsulada
IECEx BAS 13.0012U Encapsulados EATON MEDC Resistor/Diodo
Encapsulated LED and Resistor Units Encapsulated Resistor/Diode assembly
AKZ 4EX
IECEx SIR 05.0038U Terminal Weidmuller
AKZ 2.5
IECEx SIR 05.0035U Terminal Weidmuller BK 6
IECEx KEM 07.0061U Terminal Phoenix MBK2.5/E
AKZ 4
IECEx TUR 18.0024U Terminal Weidmuller
AKZ 2.5
IECEx TUR 18.0019U Terminal Weidmuller BK 6/E

O invólucro pode ser fornecido como uma moldagem pigmentada preta sem tratamento de superfície adicional ou pode ser fornecido
revestido externamente com uma tinta epóxi pigmentada ou acrílica.

Os terminais listados na Tabela 3 acima são analisados de acordo com os requisitos mais recentes da IEC 60079-0: 2017 Edição 7 e
IEC 60079-7: 2015 Edição 5 e considerados adequados para a montagem.

Além disso, os terminais AKZ 4 AKZ 2.5 e BK 6 / E mostram conformidade com IEC 60079-7: 2017 Edição 5.1

O invólucro pode ser fornecido como o molde pigmentado preto sem tratamento de superfície adicional ou pode ser fornecido revestido
externamente com um sistema de tinta epóxi ou acrílica pigmentada.

The enclosure may be supplied as the black pigmented moulding without additional surface treatment or may be supplied coated externally with a
pigmented epoxy or acrylic paint system.

The terminals as listed in Table 3 above, are reviewed against the latest requirements of IEC 60079-0:2017 Edition 7 and IEC 60079-7:2015 Edition 5
and considered suitable for the assembly.

In addition the AKZ 4 AKZ 2.5 and BK 6/E terminals show compliance with IEC 60079-7:2017 Edition 5.1

The enclosure may be supplied as the black pigmented molding without additional surface treatment or may be supplied coated externally with a
pigmented epoxy or acrylic paint system.

VALORES DA ALIMENTAÇÃO ELÉTRICA:

a) Para versões equipadas com até dois micro-interruptores somente - os valores máximos para cada interruptor instalado são os
especificados na Tabela 1.

b) Para versões equipadas com invólucro encapsulado - os valores máximos do sistema são detalhados na Tabela 2; consulte a Tabela
4 para obter valores de resistência alternativos.

ELECTRICAL SUPPLY RATINGS:

a) For versions which are equipped with up to two micro switches only – the maximum values for each switch fitted are as specified in Table 1.

b) For versions which are equipped with encapsulated housing – the maximum system values are detailed in Table 2; refer to Table 4 for alternative
resistor values.

UL do Brasil Certificações – CNPJ 04.830.102/0001-95

Av. Engenheiro Luís Carlos Berrini, 105 – 23º Andar
Página/Page: 5 / 9
São Paulo – SP – Brasil - 04571-010 – https://latam.ul.com/
Form-ULID-017660 – Rev. 3.0
 Certificado de Conformidade
Certificate of Conformity
Certificado/Certificate: UL-BR 15.0936X / 00
Emissão/Issue Revisão/Review: 06 Validade/Expiration
26 de abril de 2016 25 de abril de 2028
April 26, 2016 April 25, 2028

Tabela 4 / Table 4
Valores Mínimos dos Resistores
Minimum Resistor Values

R1Min R2Min
A 100 Ω 180 Ω
B 250 Ω 47 Ω

CONDIÇÕES ESPECÍFICAS DE UTILIZAÇÃO PARA EQUIPAMENTOS Ex ou LISTA DE LIMITAÇÕES PARA

COMPONENTES Ex:
SPECIFIC CONDITIONS OF USE FOR Ex EQUIPMENT or SCHEDULE OF LIMITATIONS FOR Ex COMPONENTS:

1. As unidades devem ser incorporadas em sistemas que limitem os valores elétricos de alimentação – ver tabelas sob
“CARACTERÍSTICAS ELÉTRICAS”.

2. As terminações de cabos entre as partes fixas e móveis dos invólucros devem ser alojadas, durante a montagem, de forma que
os condutores e seus reforços não fiquem presos na face de conexão entre os invólucros.

3. Os prensa-cabos instalados nos modelos BGE, BG2E e PBE devem ser fornecidos com anéis de vedação para manter a
classificação IP66 do invólucro.

4. As unidades LED encapsuladas e as unidades resistor/diodo encapsuladas devem ser protegidas por um fusível adequado para
corrente de curto-circuito de, no mínimo, 1500 A.

1. The units must be incorporated in systems which limit the electrical supply ratings - see Tables under “ELECTRICAL CHARACTERISTICS”.

2. The wiring loom between the fixed and detachable enclosure shell must be located, during assembly, such that the conductors and the restraint
loop are not trapped in the sealing face between the shells.

3. The cable glands installed on the BGE, BG2E and PBE models are to be provided with sealing washers to maintain the IP66 rating of the enclosure.

4. The encapsulated LED and an encapsulated resistor/diode units shall be protected by a fuse rated for a prospective short circuit current of at least
1500A.

ENSAIOS DE ROTINA / ROUTINE TESTS:

Nenhum / None

LISTA DE DOCUMENTOS / DOCUMENTS LIST:

☒Description ILL# Revisão ou Data:

Desenho Nº
☐TestRef ILL# Título / Title:
Drawing No.: Issue or Date
(DD/MM/YYYY)
01 Certification Wiring Diagrams BGE/BG2E/PBE 280-665 D
02 ATEX/IECEx Certification GA BGE/BG2E Break Glass 280-656 J
03 ATEX/IECEx Certification GA PBE Push Button 380-447 H
04 BGE/BG2E Break Glass INMETRO Certification Label 280-960 H
05 PBE Push Button INMETRO Certification Label 380-935 G
06 Technical Manual BG/PB – Ex e versions (English / Portuguese) TM349 A (2022-06)
07 General arrangement INMETRO packaging box label 322-145 B

UL do Brasil Certificações – CNPJ 04.830.102/0001-95

Av. Engenheiro Luís Carlos Berrini, 105 – 23º Andar
Página/Page: 6 / 9
São Paulo – SP – Brasil - 04571-010 – https://latam.ul.com/
Form-ULID-017660 – Rev. 3.0
 Certificado de Conformidade
Certificate of Conformity
Certificado/Certificate: UL-BR 15.0936X / 00
Emissão/Issue Revisão/Review: 06 Validade/Expiration
26 de abril de 2016 25 de abril de 2028
April 26, 2016 April 25, 2028

CERTIFICADO DE CONFORMIDADE, RELATÓRIOS DE ENSAIO / CERTIFICATE OF CONFORMANCE, TEST

REPORTS:

☒TestRec DS# Revisão ou Data:

Título/Descrição: Documento Nº
☐TestRef DS#
Title/Description: Document No.: Issue or Date
(DD/MM/YYYY)
01 IECEx BAS 18.0100X 2020-09-17
Certificado IECEx, emitido por SGS Baseefa Limited
Issue No. 1
02 Relatório de ensaio, emitido por SGS Baseefa Limited GB/BAS/ExTR18.0326/00 2019-03-08
03 Relatório de ensaio, emitido por SGS Baseefa Limited 16(C)0089 2016-05-19
04 Relatório de ensaio, emitido por SGS Baseefa Limited 12(C)1004 2013-08-20
05 Relatório de ensaio, emitido por Baseefa 10(C)0640 2012-07-12
06 Relatório de ensaio, emitido por Baseefa 01(C)1067 2002-05-08
07 Relatório de ensaio, emitido por Baseefa 05(T)0051 2011-11-23
08 Relatório de ensaio, emitido por Baseefa 93(C)042 1993-04-05
09 Relatório de ensaio, emitido por Baseefa 93(C)225 1993-07-30
10 Relatório de ensaio, emitido por Baseefa 94(C)0129 1995-07-31
11 Relatório de ensaio, emitido por SGS Baseefa Limited GB/BAS/ExTR13.0019/00 2013-08-20
12 Relatório de ensaio, emitido por SGS Baseefa Limited GB/BAS/ExTR15.0237/00 2015-08-25
13 Relatório de ensaio, emitido por SGS Baseefa Limited GB/BAS/ExTR17.0043/00 2017-02-08
14 Relatório de ensaio, emitido por SGS Baseefa Limited GB/BAS/ExTR18.0222/00 2018-09-03
15 Relatório de ensaio, emitido por SGS Baseefa Limited GB/BAS/ExTR20.0145/00 2020-09-17

Informações de auditoria/Audit information:

Local da auditoria/Audit location Data de realização/Perform date
Tratamento de reclamações/ 13 de dezembro de 2023
Complaint handling December 13, 2023
(UL Audit File: A28685)
Fabricante/ 23 de fevereiro de 2023
Manufacturer February 23, 2023
(UL Audit File: A28386)

UL do Brasil Certificações – CNPJ 04.830.102/0001-95

Av. Engenheiro Luís Carlos Berrini, 105 – 23º Andar
Página/Page: 7 / 9
São Paulo – SP – Brasil - 04571-010 – https://latam.ul.com/
Form-ULID-017660 – Rev. 3.0
 Certificado de Conformidade
Certificate of Conformity
Certificado/Certificate: UL-BR 15.0936X / 00
Emissão/Issue Revisão/Review: 06 Validade/Expiration
26 de abril de 2016 25 de abril de 2028
April 26, 2016 April 25, 2028

Observações/Observations:
1. A validade deste Certificado de Conformidade está atrelada à realização das avaliações de manutenção e tratamento
de possíveis não conformidades de acordo com as orientações da UL do Brasil Certificações previstas no RAC
específico. Para verificação da condição atualizada de regularidade deste Certificado de Conformidade deve ser
consultado o banco de dados de produtos e serviços certificados do Inmetro.
The validity of this Certificate of Conformity is linked to the performance of maintenance assessments and treatment of possible non-
conformities in accordance with the guidelines of UL do Brasil Certifications provided for in the specific Conformity Assessment
Regulation. To check the updated condition of regularity of this Certificate of Conformity, the Inmetro database of certified products
and services must be consulted.

2. Este certificado aplica-se aos equipamentos (produtos) idênticos ao protótipo avaliado e certificado, manufaturados
na(s) unidade(s) fabril(is) mencionada (s) acima.
This certificate applies to the products that are identical to the prototype investigated, certified and manufactured at the production
site mentioned in this certificate.

3. Qualquer alteração no produto, incluindo a marcação, invalidará o presente certificado, salvo se o solicitante informar
por escrito à UL do Brasil Certificações sobre esta modificação, a qual procederá à avaliação e decidirá quanto à
continuidade da validade do certificado.
Any non-authorized changes performed in the product, including marking, will invalidate this certificate. UL do Brasil Certificações
must be notified about any desired change. This notification will be analyzed by UL do Brasil Certificações that will decide about
certificate force.

4. Esta autorização está vinculada a um contrato e para o escopo acima citado.

This license is related to a commercial proposal and to the scope above cited.

5. Somente as unidades comercializadas durante a vigência deste certificado estarão cobertas por esta certificação.
Only the products placed into the market during the validity of this certificate will be covered by this certification.

6. Os equipamentos devem ser instalados em atendimento às Normas pertinentes em Instalações Elétricas em

Atmosferas Explosivas, ABNT NBR IEC 60079-14.
The equipment shall be installed according to the relevant Standards in Electrical Installation for Explosive Atmospheres, ABNT NBR
IEC 60079-14.

7. As atividades de instalação, inspeção, manutenção, reparo, revisão e recuperação dos equipamentos são de
responsabilidade dos usuários e devem ser executadas de acordo com os requisitos das normas técnicas vigentes e
com as recomendações do fabricante.
The installation, inspection, maintenance, repair, review and rebuild equipment activities are responsibility of the end user and must
be performed in accordance with the requirements of the standards and manufacturer's recommendation.

UL do Brasil Certificações – CNPJ 04.830.102/0001-95

Av. Engenheiro Luís Carlos Berrini, 105 – 23º Andar
Página/Page: 8 / 9
São Paulo – SP – Brasil - 04571-010 – https://latam.ul.com/
Form-ULID-017660 – Rev. 3.0
 Certificado de Conformidade
Certificate of Conformity
Certificado/Certificate: UL-BR 15.0936X / 00
Emissão/Issue Revisão/Review: 06 Validade/Expiration
26 de abril de 2016 25 de abril de 2028
April 26, 2016 April 25, 2028

Histórico de revisões/Revisions history:

Revisão/ Data/ Descrição da revisão/
Review Date Revision description
Project 4791535038.8.1:
Atualização do certificado de acordo com os requisitos mais recentes da
Portaria INMETRO 115:2022, incluindo atualização do Solicitante,
atualização para as últimas edições das normas de avaliação, atualização
30 de abril de 2025 das etiquetas de marcação (produto e embalagem), atualização do manual
06
April 30, 2025 de instruções do produto e extensão da data de validade do certificado.
Update of the certificate in accordance with the latest requirements of INMETRO Portaria
115:2022, covering update of Certificate Holder, update of evaluation standard versions,
update to marking labels (product and package), update of product’s instructions and extension
of certificate validity date.

31 de março de 2022 Project 4790348952:

05 Renovação do Certificado.
March 31, 2022
Certificate Renewal.
Project 4789800223:
22 de abril de 2021 Revisão do certificado cobrindo atualização de desenhos e correção da
04 referência do número de terminais usado no produto.
April 22, 2021
Certificate revision to reflect the amend drawings to correctly reference new certification
numbers of the terminals used within the product.
Project 4788718828.9.1:
Atualizações cobrindo: 1) Alteração da referência ao certificado de origem
26 de maio de 2019 (de ATEX para IECEx), 2) Atualização das normas de referência,
03
May 26, 2019 3) Alteração geral da descrição do produto.
Updates covering: 1) Change of the origin certificate reference (from ATEX to IECEx), 2)
Update on standard references, 3) Overall product description updates.

23 de abril de 2019 Project 5108100.1197408:

02 Renovação do Certificado.
April 23, 2019
Certificate Renewal.
Project 4787873572.16.1:
Revisão do certificado para refletir a alteração do nome do
17 de janeiro de 2018 solicitante/fabricante de Cooper MEDC Limited para Eaton MEDC Limited
01
January 17, 2018 e atualização da marcação Ex e parâmetros elétricos.
Certificate revision to reflect applicant/manufacturer name change from Cooper MEDC Limited
to Eaton MEDC Limited and updates on the Ex marking and electrical parameters.

26 de abril de 2016 Project 4787042099.11.1:

00 Emissão Inicial
April 26, 2016
Initial issue
A última revisão substitui e cancela as anteriores/
The last review replaces and cancels the previous ones

UL do Brasil Certificações – CNPJ 04.830.102/0001-95

Av. Engenheiro Luís Carlos Berrini, 105 – 23º Andar
Página/Page: 9 / 9
São Paulo – SP – Brasil - 04571-010 – https://latam.ul.com/
Form-ULID-017660 – Rev. 3.0
 Print Back

Government of India
Ministry of Commerce & Industry
Petroleum & Explosives Safety Organisation (PESO)
5th Floor, A-Block, CGO Complex, Seminary Hills,
Nagpur - 440006

E-mail : [email protected]
Phone/Fax No : 0712 -2510248, Fax-2510577

Approval No : A/P/HQ/TN/104/6267 (P549522) Dated : 27/10/2022

To,
M/s. Eaton MEDC Limited,
Unit B, Sutton Parkway, Oddicroft Lane,,Sutton-in-Ashfield
NG17 5FB
UK

Sub : Approval of Flame Proof, Encapsulated, Increased Safety Type Electrical Equipment under Petroleum Rules
2002- Regarding.
Sir(s),
Please refer to your letter No. OIN1177171 dated 10/10/2022 on the subject.
The following Ex electrical equipment(s) manufactured by you according to IEC 60079-0 : 2017, IEC 60079-1
: 2014-06, IEC 60079-7 : 2017, IS/IEC 60079-18 : 2014, standards and covered under SGS Baseefa
Limited Test reports mentioned below is/are approved for use in Zone 2 of Gas IIC hazardous areas
coming under the the Petroleum Rules, 2002 administered by this Organization.

Equipment Test Agency

Sr. Safety Drawing
Description reference Certificate Certificate
No Protection Name no
Number No. Date
Ex db eb IECEx BAS As per
BG2E model fitted with SGS Baseefa
1 mb IIC T4 P549522/1 18.0100X 17/09/2020 test
LEDs and Resistors Limited
Gb Issue 1 report
Ex db eb IECEx BAS As per
BG2E model fitted with SGS Baseefa
2 mb IIC T6 P549522/2 18.0100X 17/09/2020 test
LEDs Limited
Gb Issue 1 report
Ex db eb IECEx BAS As per
BGE model fitted with SGS Baseefa
3 mb IIC T4 P549522/3 18.0100X 17/09/2020 test
Resistors Limited
Gb Issue 1 report
Ex db eb IECEx BAS As per
PBE model fitted with SGS Baseefa
4 mb IIC T4 P549522/4 18.0100X 17/09/2020 test
LEDs and Resistors Limited
Gb Issue 1 report
Ex db eb IECEx BAS As per
PBE model fitted with SGS Baseefa
5 mb IIC T6 P549522/5 18.0100X 17/09/2020 test
LEDs Limited
Gb Issue 1 report
Ex db eb IECEx BAS As per
BGE model fitted with SGS Baseefa
6 mb IIC T4 P549522/6 18.0100X 17/09/2020 test
LEDs and Resistors Limited
Gb Issue 1 report
BGE model fitted only IECEx BAS As per
Ex db eb SGS Baseefa
7 with Switches (no LEDs P549522/7 18.0100X 17/09/2020 test
IIC T6 Gb Limited
or Resistors) Issue 1 report
Ex db eb IECEx BAS As per
BG2E model fitted with SGS Baseefa
8 mb IIC T4 P549522/8 18.0100X 17/09/2020 test
Resistors Limited
Gb Issue 1 report
 Ex db eb IECEx BAS As per
PBE model fitted with SGS Baseefa
9 mb IIC T4 P549522/9 18.0100X 17/09/2020 test
Resistors Limited
Gb Issue 1 report
PBE model fitted only IECEx BAS As per
Ex db eb SGS Baseefa
10 with Switches (no LEDs P549522/10 18.0100X 17/09/2020 test
IIC T6 Gb Limited
or Resistors) Issue 1 report
BG2E model fitted only IECEx BAS As per
Ex db eb SGS Baseefa
11 with Switches (no LEDs P549522/11 18.0100X 17/09/2020 test
IIC T6 Gb Limited
or Resistors) Issue 1 report
Ex db eb IECEx BAS As per
BGE model fitted with SGS Baseefa
12 mb IIC T6 P549522/12 18.0100X 17/09/2020 test
LEDs Limited
Gb Issue 1 report

This Approval is granted subject to observance of the following conditions:-

1)The design and construction of the equipment shall be strictly in accordance with description, condition and
drawings as mentioned in the SGS Baseefa Limited Test Reports referred to above.

2)The equipment shall be used only with approved type of accessories and associated apparatus.

3)Each equipment shall be marked either by raised lettering cast integrally or by plate attached permanently to the
main structure to indicate conspicuously:-
(a) Name of the manufacturer
(b) Name and number by which the equipment is identified.
(c) Number & date of the test report of the SGS Baseefa Limited applicable to the equipment.
(d) Equipment reference number of this letter by which use of apparatus is approved.
(e) Protection level.

4) A certificate to the effect that the equipment has been manufactured strictly in accordance with the drawing
referred to in the SGS Baseefa Limited Test report and is identical with the one tested and certified at SGS
Baseefa Limited shall be furnished with each equipment.
5) The customer shall be supplied with a copy of this letter, an extract of the conditions and maintenence
schedule, if any, recommended by SGS Baseefa Limited in their test reports and copy of instructions booklet
detailing operation & maintenance of the equipment so as to maintain its Flame Proof characterestics.
6) The After sales service and maintanance of subject equipment shall be looked after by your representative MTL
Instruments Private Limited, 3, Old Mahabalipuram Road, Sholinganallur, Chennai 600119

Conditions of the Approval:-

The approval for above equipment is subject to validity of IECEx Quality Assessment Report No.
GB/BAS/QAR06.0023.

This approval also covers the permissible variations as approved under the SGS Baseefa Limited test reports
referred above. This approval is liable to be cancelled if any of the conditions of the approval is violated or not
complied with . The approval may also be amended or withdrawn at any time, if considered necessary in the interest
of safety.

The field performance report from actual users/your customers of the subject equipment may please be
collected and furnished to this office for verification and record on annual basis.
The Approval is Valid upto 31/12/2026

Yours faithfully,

(A.B. Tamgadge)
Dy. Chief Controller of Explosives
For Chief Controller of Explosives
Nagpur
Copy to :
1. Jt. Chief Controller of Explosives, South Circle Office, CHENNAI
2. MTL Instruments Private Limited,3, Old Mahabalipuram Road, Sholinganallur, Chennai 600119
for Chief Controller of Explosives
Nagpur
(For more information regarding status,fees and other details please visit our website http://peso.gov.in)
This is System Generated document. Signature is not required.
Disclaimer : This page gives the latest action taken by this organization on your application. This page is
made available for the information of concerned applicant/licensee only. All efforts have been made to secure
this information. However, PESO will not be responsible for any misuse of the information by unauthorized
persons including the hackers.
 Print Back

Government of India
Ministry of Commerce & Industry
Petroleum & Explosives Safety Organisation (PESO)
5th Floor, A-Block, CGO Complex, Seminary Hills,
Nagpur - 440006

E-mail : [email protected]
Phone/Fax No : 0712 -2510248, Fax-2510577

Approval No : A/P/HQ/TN/104/6267 (P549522) Dated : 27/10/2022

To,
M/s. Eaton MEDC Limited,
Unit B, Sutton Parkway, Oddicroft Lane,,Sutton-in-Ashfield
NG17 5FB
UK

Sub : Approval of Flame Proof, Encapsulated, Increased Safety Type Electrical Equipment under Petroleum Rules
2002- Regarding.
Sir(s),
Please refer to your letter No. OIN1177171 dated 10/10/2022 on the subject.
The following Ex electrical equipment(s) manufactured by you according to IEC 60079-0 : 2017, IEC 60079-1
: 2014-06, IEC 60079-7 : 2017, IS/IEC 60079-18 : 2014, standards and covered under SGS Baseefa
Limited Test reports mentioned below is/are approved for use in Zone 2 of Gas IIC hazardous areas
coming under the the Petroleum Rules, 2002 administered by this Organization.

Equipment Test Agency

Sr. Safety Drawing
Description reference Certificate Certificate
No Protection Name no
Number No. Date
Ex db eb IECEx BAS As per
BG2E model fitted with SGS Baseefa
1 mb IIC T4 P549522/1 18.0100X 17/09/2020 test
LEDs and Resistors Limited
Gb Issue 1 report
Ex db eb IECEx BAS As per
BG2E model fitted with SGS Baseefa
2 mb IIC T6 P549522/2 18.0100X 17/09/2020 test
LEDs Limited
Gb Issue 1 report
Ex db eb IECEx BAS As per
BGE model fitted with SGS Baseefa
3 mb IIC T4 P549522/3 18.0100X 17/09/2020 test
Resistors Limited
Gb Issue 1 report
Ex db eb IECEx BAS As per
PBE model fitted with SGS Baseefa
4 mb IIC T4 P549522/4 18.0100X 17/09/2020 test
LEDs and Resistors Limited
Gb Issue 1 report
Ex db eb IECEx BAS As per
PBE model fitted with SGS Baseefa
5 mb IIC T6 P549522/5 18.0100X 17/09/2020 test
LEDs Limited
Gb Issue 1 report
Ex db eb IECEx BAS As per
BGE model fitted with SGS Baseefa
6 mb IIC T4 P549522/6 18.0100X 17/09/2020 test
LEDs and Resistors Limited
Gb Issue 1 report
BGE model fitted only IECEx BAS As per
Ex db eb SGS Baseefa
7 with Switches (no LEDs P549522/7 18.0100X 17/09/2020 test
IIC T6 Gb Limited
or Resistors) Issue 1 report
Ex db eb IECEx BAS As per
BG2E model fitted with SGS Baseefa
8 mb IIC T4 P549522/8 18.0100X 17/09/2020 test
Resistors Limited
Gb Issue 1 report
 Ex db eb IECEx BAS As per
PBE model fitted with SGS Baseefa
9 mb IIC T4 P549522/9 18.0100X 17/09/2020 test
Resistors Limited
Gb Issue 1 report
PBE model fitted only IECEx BAS As per
Ex db eb SGS Baseefa
10 with Switches (no LEDs P549522/10 18.0100X 17/09/2020 test
IIC T6 Gb Limited
or Resistors) Issue 1 report
BG2E model fitted only IECEx BAS As per
Ex db eb SGS Baseefa
11 with Switches (no LEDs P549522/11 18.0100X 17/09/2020 test
IIC T6 Gb Limited
or Resistors) Issue 1 report
Ex db eb IECEx BAS As per
BGE model fitted with SGS Baseefa
12 mb IIC T6 P549522/12 18.0100X 17/09/2020 test
LEDs Limited
Gb Issue 1 report

This Approval is granted subject to observance of the following conditions:-

1)The design and construction of the equipment shall be strictly in accordance with description, condition and
drawings as mentioned in the SGS Baseefa Limited Test Reports referred to above.

2)The equipment shall be used only with approved type of accessories and associated apparatus.

3)Each equipment shall be marked either by raised lettering cast integrally or by plate attached permanently to the
main structure to indicate conspicuously:-
(a) Name of the manufacturer
(b) Name and number by which the equipment is identified.
(c) Number & date of the test report of the SGS Baseefa Limited applicable to the equipment.
(d) Equipment reference number of this letter by which use of apparatus is approved.
(e) Protection level.

4) A certificate to the effect that the equipment has been manufactured strictly in accordance with the drawing
referred to in the SGS Baseefa Limited Test report and is identical with the one tested and certified at SGS
Baseefa Limited shall be furnished with each equipment.
5) The customer shall be supplied with a copy of this letter, an extract of the conditions and maintenence
schedule, if any, recommended by SGS Baseefa Limited in their test reports and copy of instructions booklet
detailing operation & maintenance of the equipment so as to maintain its Flame Proof characterestics.
6) The After sales service and maintanance of subject equipment shall be looked after by your representative MTL
Instruments Private Limited, 3, Old Mahabalipuram Road, Sholinganallur, Chennai 600119

Conditions of the Approval:-

The approval for above equipment is subject to validity of IECEx Quality Assessment Report No.
GB/BAS/QAR06.0023.

This approval also covers the permissible variations as approved under the SGS Baseefa Limited test reports
referred above. This approval is liable to be cancelled if any of the conditions of the approval is violated or not
complied with . The approval may also be amended or withdrawn at any time, if considered necessary in the interest
of safety.

The field performance report from actual users/your customers of the subject equipment may please be
collected and furnished to this office for verification and record on annual basis.
The Approval is Valid upto 31/12/2026

Yours faithfully,

(A.B. Tamgadge)
Dy. Chief Controller of Explosives
For Chief Controller of Explosives
Nagpur
Copy to :
1. Jt. Chief Controller of Explosives, South Circle Office, CHENNAI
2. MTL Instruments Private Limited,3, Old Mahabalipuram Road, Sholinganallur, Chennai 600119
for Chief Controller of Explosives
Nagpur
(For more information regarding status,fees and other details please visit our website http://peso.gov.in)
This is System Generated document. Signature is not required.
Disclaimer : This page gives the latest action taken by this organization on your application. This page is
made available for the information of concerned applicant/licensee only. All efforts have been made to secure
this information. However, PESO will not be responsible for any misuse of the information by unauthorized
persons including the hackers.
 Certificate Num ber
Baseefa03ATEX0084X Issued 14 Septem ber 2016
Issue 6 Page 1 of 3

1 ED - TYPE EXAMINATION CERTIFICATE

2 Equipment or Protective System I ntended for use in Potentially Explosive Atmospheres
Directive 2014/34/EU
3 EU - Type Examination Certificate Baseefa03ATEX0084X - Issue 6
Number:

3.1 In accordance with Article 41 of Directive 20 14/34/EU , EC-Type Examination Certificates referring to 94/9/EC that were in
existence prior to the date of application of2014/34/EU (20 April 2016) may be referenced as if they were issued in accordance
with Directive 20 l4/34/EU. Supplementary Certificates to such EC-Type Examination Certificates, and new issues of such
certificates, may continue to bear the original certificate number issued prior to 20 April 2016.

4 Product: M anua l Call Point Type P BI 1BG I

5 Manufacturer: Eaton M EDC Limited

6 Address: Unit B, Sutton Parkway, Oddicroft Lane, Sutton-in-Ashfield, NG175FB

7 This re-issued certificate extends EC Type Examination Certificate No. Baseefa03ATEX0084X to apply to product designed
and constructed in accord ance with the specification set out in the Schedule of the said certificate but having an y variations
specified in the Schedule attached to this certificate and the documents therein referred to.

8 SOS Baseefa, Notified Body number 1180, in accordance with Article 17 of Directive 20 14/34/EU of the European Parliament
and of the Council, dated 26 February 2014 , certifies that this product has been found to comply with the Essential Health and
Safety Requirements relating to the design and construction of products intended for use in potentially explosive atmospheres
given in Annex II to the Directive.

The examination and test results are recorded in confidenti al Report No. See Certificate History

9 Compliance with the Essential Health and Safety Requirements has been assured by compliance with:

EN 60079-0:2012+All :20 13 EN 60079-11:2012

except in respect of those requirements listed at item 18 of the Schedule.

10 If the sign "X" is placed after the certificate number, it indicates that the product is subject to the Specific Conditions of Use
specified in the schedule to this certificate.

11 This EU - TYP E EXAMINATION CERTIFICATE relates only to the design and construction of the specified product.
Further requirements of the Directive appl y to the manufacturing process and suppl y of this product. These are not covered by
this certi ficate.

12 The marking of the product shall include the following:

® II 1 GD Ex ia II C T4 Ga

Ex ia IIIC T 135°C Da

SOS Baseefa Customer Reference No. 0676 Project File No. 16/0088

This document is issued by the Company subject to its General Conditions for Certification Services accessible at http ://www.sgs .com/enrrerms-and-
Conditions.aspx and the Supplementary Terms and Conditions accessible at http ://www .sgs .com/SGSBaseefafferms-and-Conditions.aspx Attention is drawn to
the limitation of liability , indemnification and jurisdiction issues defined therein . Any holder of this document is advised that information contained herein
reflects the Company's findings at the time of its intervention only and within the limits of Client's instructions, if any. It does not necessarily indicate that the
equipment may be used in particular industries or circum stanc es. The Company' s sole responsibility is to its Client and this document does not exonerate
parties to a tran saction from exercising all their right s and obli gations under the transaction documents. This document cannot be reproduced except in full,
schedule included , without prior written approval of the Company. Any unauth or ized alteration, forgery or falsific ation of the content or appearance of this
docum ent is unlawful and offe nders may be prosecuted to the fullest extent of the law.

SGS Baseefa Lim ited

Rockhead Business Park, Staden Lane,
JJ&~vd
Buxton , Derbyshire SK17 9RZ
Telephone +44 (0) 1298 766600 Fax +44 (0) 1298 766601
e-mail baseefa@sgs .com web site www .sgs.co.uk/baseefa
R S SINCLAIP W~Av?U;:"j
TECHNICAL MANAGER
Registered in England No. 4305578.
Registered addr ess: Rossmore Business Park, Ellesmere Port, Cheshire, CH65 3EN
On behalf of SGS Baseefa Limited
 Certificate Num ber
Iss ued 14 September 2016
Baseefa03ATEX0084X
Page 2 of 3
Issue 6

13 Sc ed ule
14 Certificate Number Baseefa03ATEX0084X - Issue 6

15 Descript ion of Product

The Manual Call Po int Type PBI / BGI is designed to initiate an elect rical signal when the alarm switch is operate d.
Alternative versions can provide local LED indication.

The unit comprises of a polyester enclosure with an optional epoxy or acrylic paint finish, terminal block and a push button
switch under a flap or a break glass switch unit. Different versions contain resistors and / or zener diodes. These
components may optionally be mounted on an encapsulated PCB. An optional end-o f-line resistor may be added.

External connections are made at the terminals via gland entries at the bottom of the unit.

Input Paramet ers

Group IIC (Ex ia IIC T4 Ga)

Vi 30V C o
I1 147mA I-I o
p I. 0.8W

Group IIIC (Ex ia IIIC T 135°C Da)

28V o
93mA o
0.65W

16 Rep ort Number

GB/BAS /ExTRI6.0249/00

17 Sp ecifi c Conditions of Use

1. The Manual Call Point has a plastic enclosure which must only be cleaned with a damp cloth to avo id the danger
of ignition due to a build-up of an electrostatic charge.
2. The Manual Call Point must only be fitted with approved Ex e glands and blanking plugs that will maintain the
ingress protection to at least IP6X.

18 Essential Hea lth and Sa fety Requirements

In addition to the Essential Health and Safety Requi rements (EH SRs) covered by the standards listed at item 9, the
following are considered relevant to this product:

Clause Subj ect Compliance

1.2.7 LVD type requi rements Manufacturer responsibility

1.2.8 Overloading of equipment (protection relays , etc.) User/Installer responsibility
1.4. 1 External effects User/Installer responsibility
1.4.2 Agg ressive substances, etc. User/Installer responsibility

19 Drawings and Documents

New dra wing s submitted for this issue of cert ificate :

Numbe r Shee t Issu e Date Description

280-657 1 of 1 D 29-01-16 General Assembly - BG I/BG2 I Break Gla ss

 Certificate Number
Baseefa03ATEX0084X Issue d 14 Septem ber 2016
Issue 6 Page 3 of 3

Current drawings which remain unaffected by this issue:

Number Sheet Issue Date Description

122-808 1 of 1 1 05-03-07 Addition of Optional Acrylic Paint

280-658 1 of 1 B 22-04-02 BGI/BG21 Breakglass ATEX Cert Label
280-676 1 to 5 A 17-04-02 Wiring Diagram
380-448 1 of 1 A 22-04-02 General Assembly
380-456 1 of 1 B 22-04-02 PBI Pushbutton ATEX Cert Label
All drawings are common to, and held with, IECEx BAS 12.0093X.

20 Certificate History
Certificate No. Date Comments
The release of the prime certificate. The associated test and
assessment against the requirements of EN 50014: 1997 + Amd 1 &
Baseefa03ATEX0084X 27 February 2003 2, EN 50020: 2002 , EN 50284: 1999 & EN 50281- 1-1: 1998 is
documented in Test Report No. 02(C)0186. Project File No.
02/0186.
To permit modifications to introduce the BGI break glass call point.
Baseefa03ATEX0084X/l 28 April 2003
Project File No. 03/0236.

Baseefa03ATEX0084X/2 24 April 2007 To permit the use of epoxy or acrylic paint processes. Project File
No. 07/0181.
Baseefa03ATEX0084X/3 4 January 2008 To permit the use of an alternative enclosure material. Project File
No. 07/0852.
To permit minor drawing changes and to confirm that the original
Baseefa03ATEX0084X/4 2 September 2010 special condition of safe use stated at 17.3 (UV exposure) no longer
applies. Project File No.1 0/0075 .
To confirm that the equipment meets the requirements of IEC
60079-0:2011/EN 60079-0:201 2 & EN 60079-11 :2012, including
Baseefa03ATEX0084X/5 3 September 2012
revision of the marking. Report No . GB/BAS /ExTRI2.0220/00.
Project File No . 12/0715.
This issue of the certificate incorporates previousl y issued primary
& supplementary certificates into one certificate, perm its minor
mechanical changes and confirms the current design meets the
Baseefa03ATEX0084X requirements of EN 60079-0:2012+All :2013. Report No .
14 September 2016
Issue 6 GB/BAS/ExTRI6.0249/00. Project File No. 16/0088. A lso to
permit existing information (for example on Schedule Drawings) to
be replaced by the revised certificate holders name. No other
changes may be made to the certified design
For drawings applicable to each issue, see original of that issue.
 Certificate Number
Issued 1 November 2021
Baseefa03ATEX0084X
Page 1 of 3
Issue 7

1 EU - TYPE EXAMINATION CERTIFICATE

2 Equipment or Protective System Intended for use in Potentially Explosive Atmospheres
Directive 2014/34/EU
3 EU - Type Examination Certificate Baseefa03ATEX0084X – Issue 7
Number:
3.1 In accordance with Article 41 of Directive 2014/34/EU, EC-Type Examination Certificates referring to 94/9/EC that were in
existence prior to the date of application of 2014/34/EU (20 April 2016) may be referenced as if they were issued in accordance
with Directive 2014/34/EU. Supplementary Certificates to such EC-Type Examination Certificates, and new issues of such
certificates, may continue to bear the original certificate number issued prior to 20 April 2016.
4 Product: Manual Call Point Type PBI / BGI
5 Manufacturer: Eaton MEDC Limited
6 Address: Unit B, Sutton Parkway, Oddicroft Lane, Sutton-in-Ashfield, NG17 5FB
7 This re-issued certificate extends EC Type Examination Certificate No. Baseefa03ATEX0084X to apply to product designed
and constructed in accordance with the specification set out in the Schedule of the said certificate but having any variations
specified in the Schedule attached to this certificate and the documents therein referred to.
8 SGS Fimko Oy, Notified Body number 0598, in accordance with Article 17 of Directive 2014/34/EU of the European
Parliament and of the Council, dated 26 February 2014, certifies that this product has been found to comply with the Essential
Health and Safety Requirements relating to the design and construction of products intended for use in potentially explosive
atmospheres given in Annex II to the Directive.
8.1 The original certificate was issued by SGS Baseefa Ltd (UK Notified Body 1180). It, and any supplements previously issued by
SGS Baseefa Ltd have been transferred to the supervision of SGS Fimko Oy (EU Notified Body 0598). The original certificate
number is retained.
The examination and test results are recorded in confidential Report No. – See Certificate History
9 Compliance with the Essential Health and Safety Requirements has been assured by compliance with:
EN IEC 60079-0: 2018 EN 60079-11: 2012
except in respect of those requirements listed at item 18 of the Schedule.
10 If the sign “X” is placed after the certificate number, it indicates that the product is subject to the Specific Conditions of Use
specified in the schedule to this certificate.
11 This EU - TYPE EXAMINATION CERTIFICATE relates only to the design and construction of the specified product. Further
requirements of the Directive apply to the manufacturing process and supply of this product. These are not covered by this
certificate.
12 The marking of the product shall include the following:

II 1 GD Ex ia IIC T4 Ga (-40°C ≤ Ta ≤ +70°C)

 Ex ia IIIC T135°C Da (-40°C ≤ Ta ≤ +70°C)

SGS Fimko Oy Customer Reference No. 0676 Project File No. 21/0385

This document is issued by the Company subject to their General Conditions for Certification Services accessible at http://www.sgs.com/en/Terms-and-
Conditions.aspx . Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is
advised that information contained herein reflects the Company’s findings at the time of their intervention only and within the limits of Client’s instructions,
if any. It does not necessarily indicate that the equipment may be used in particular industries or circumstances. The Company’s sole responsibility is to
its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents.
This document cannot be reproduced except in full, schedule included, without prior written approval of the Company. Any unauthorized alteration, forgery
or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law .

SGS Fimko Oy
Takomotie 8
FI-00380 Helsinki, Finland
Telephone +358 (0)9 696 361
e-mail [email protected]
web site www.sgs.fi Tuomas Hänninen
Business ID 0978538-5 Member of the SGS Group (SGA SA) SGS Fimko Oy
BAS-CERT-081 SGS Baseefa Limited is an associate of SGS Fimko OY Issue 3
 Certificate Number
Issued 1 November 2021
Baseefa03ATEX0084X
Page 2 of 3
Issue 7

13 Schedule
14 Certificate Number Baseefa03ATEX0084X – Issue 7

15 Description of Product
The Manual Call Point Type PBI / BGI is designed to initiate an electrical signal when the alarm switch is operated. Alternative
versions can provide local LED indication.

The unit comprises of a polyester enclosure with an optional epoxy or acrylic paint finish, terminal block and a push button
switch under a flap or a break glass switch unit. Different versions contain resistors and / or zener diodes. These components
may optionally be mounted on an encapsulated PCB. An optional end-of-line resistor may be added.

External connections are made at the terminals via gland entries at the bottom of the unit.

Input Parameters
Group IIC (Ex ia IIC T4 Ga)

Ui = 30V Ci = 0
Ii = 147mA Li = 0
Pi = 0.8W

Group IIIC (Ex ia IIIC T135°C Da)

Ui = 28V Ci = 0
Ii = 93mA Li = 0
Pi = 0.65W

16 Report Number
See Certificate History

17 Specific Conditions of Use

1. The Manual Call Point has a plastic enclosure which must only be cleaned with a damp cloth to avoid the danger of
ignition due to a build-up of an electrostatic charge.
2. The Manual Call Point must only be fitted with approved Ex e glands and blanking plugs that will maintain the
ingress protection to at least IP6X.

18 Essential Health and Safety Requirements

In addition to the Essential Health and Safety Requirements (EHSRs) covered by the standards listed at item 9, the following
are considered relevant to this product, and conformity is demonstrated in the report:

Clause Subject Compliance

1.2.7 LVD type requirements Manufacturer responsibility

1.2.8 Overloading of equipment (protection relays, etc.) User/Installer responsibility
1.4.1 External effects User/Installer responsibility
1.4.2 Aggressive substances, etc. User/Installer responsibility

BAS-CERT-081 SGS Baseefa Limited is an associate of SGS Fimko OY Issue 3

 Certificate Number
Issued 1 November 2021
Baseefa03ATEX0084X
Page 3 of 3
Issue 7

19 Drawings and Documents

New drawings submitted for this issue of certificate:
None.
Current drawings which remain unaffected by this issue:
Number Sheet Issue Date Description

280-657 1 of 1 D 29-01-16 General Assembly - BGI/BG2I Break Glass

122-808 1 of 1 1 05-03-07 Addition of Optional Acrylic Paint
280-658 1 of 1 B 22-04-02 BGI/BG2I Breakglass ATEX Cert Label
280-676 1 to 5 A 17-04-02 Wiring Diagram
380-448 1 of 1 A 22-04-02 General Assembly
380-456 1 of 1 B 22-04-02 PBI Pushbutton ATEX Cert Label

All drawings are common to, and held with, IECEx BAS 12.0093X.

20 Certificate History
Certificate No. Date Comments
The release of the prime certificate. The associated test and
assessment against the requirements of EN 50014: 1997 + Amd 1 &
Baseefa03ATEX0084X 27 February 2003
2, EN 50020: 2002, EN 50284: 1999 & EN 50281-1-1: 1998 is
documented in Test Report No. 02(C)0186. Project File No. 02/0186.
To permit modifications to introduce the BGI break glass call point.
Baseefa03ATEX0084X/1 28 April 2003
Project File No. 03/0236.

Baseefa03ATEX0084X/2 24 April 2007 To permit the use of epoxy or acrylic paint processes. Project File
No. 07/0181.
Baseefa03ATEX0084X/3 4 January 2008 To permit the use of an alternative enclosure material. Project File
No. 07/0852.
To permit minor drawing changes and to confirm that the original
Baseefa03ATEX0084X/4 2 September 2010 special condition of safe use stated at 17.3 (UV exposure) no longer
applies. Project File No. 10/0075.
To confirm that the equipment meets the requirements of IEC 60079-
0:2011/EN 60079-0:2012 & EN 60079-11:2012, including revision
Baseefa03ATEX0084X/5 3 September 2012
of the marking. Report No. GB/BAS/ExTR12.0220/00. Project File
No. 12/0715.
This issue of the certificate incorporates previously issued primary
& supplementary certificates into one certificate, permits minor
mechanical changes and confirms the current design meets the
Baseefa03ATEX0084X
14 September 2016 requirements of EN 60079-0:2012+A11:2013. Report No.
Issue 6 GB/BAS/ExTR16.0249/00. Project File No. 16/0088. Also to
permit existing information (for example on Schedule Drawings) to
be replaced by the revised certificate holders name. No other
changes may be made to the certified design
Baseefa03ATEX0084X
1 November 2021 To assess the product against the requirements of EN IEC 60079-0:
Issue 7 2018. SGS Baseefa Certification Report 21(C)0385/01
For drawings applicable to each issue, see original of that issue.

BAS-CERT-081 SGS Baseefa Limited is an associate of SGS Fimko OY Issue 3